Can't boot iMac, problem started after loading OSX. When I press power button I see Apple logo, twirl and a bar. Looks like is loading but after few seconds it shuts it self off
I can't boot my IMac. I loaded OSX and first mail then contacts start acting up.
I shut down and now the iMac won't boot. When I press the power botton it comes on, I see Apple logo, swirl and a bar which saw loading for a few seconds and then shuts it self off.
HELP!
Try an SMC reset first, and if that doesn't help, follow up with a PRAM reset:
https://discussions.apple.com/docs/DOC-3603
If you're still having problems try a 'Safe Boot' - restart holding down the shift key until you see a grey progress bar. Once booted restart as normal from the Apple menu.
If that doesn't work, boot into the Recovery HD, launch Disky Utility and check the Macintosh HD using the 'repair disk' option. If anything gets fixed click on repair disk again until you get a clean pass, then restart as normal from the Apple menu.
To start into the Recovery HD restart holding down Command + r
More about the Recovery HD here: http://support.apple.com/kb/HT4718?viewlocale=en_US&locale=en_US
Similar Messages
-
My mini ipod appears off and not respond to any commands when pressed the buttons to reset, apple logo appeared and then the apple support site and it shuts down. already tried all the steps, but none worked, and when I plug it into my computer it does not appear in the iTunes bar. what do I do?
If MacKeeper corrupted the Recovery partition then even I underestimated its potential for damage. Garbage "cleaning" apps will cause misery but I have not found that the Recovery partition to have been affected by using MacKeeper or anything like it. I doubt that it did so, but I have learned not to underestimate the potential for such things to result in system corruption.
Before concluding your Mac has a hardware failure, try booting OS X Internet Recovery by holding command option r on startup (three fingers). That will force your iMac to bypass the Recovery partition altogether, and convey the ability to create a new one.
An Internet connection will be required (wired or wireless).
At the Mac OS X Utilities screen, select Disk Utility. Select your startup volume (usually named "Macintosh HD") and click the Repair Disk button. Describe any errors it reports in red. If Disk Utility reports "The volume Macintosh HD appears to be OK" in green then you can be reasonably (though not completely) assured your hard disk is in good working order.
Assuming the HD remains usable you can then use Disk Utility to erase it. Reinstall OS X, restore your essential software and other files, and don't reinstall the junk. -
My new HP Split X2 2 in 1 is not starting all the time when I press power button.
I brought HP Split X2 2 in 1 (tablet com laptop)1one week back and I have the prob from day 1. Press the power button for 1 sec to 10 sec for 100 tmes a day, it is starting only once per day. No one knows at which attempt it may started it may be 10th or 50th or 100th. Certenly in the begining of the day it is not startng. If it starts by luck, then it works. After it start, even if u do a shutdown and restart, it works. But go to sleep and wake up in the morning, my attempts starts. Customer care talks to you politly but each time each member has diffrent solutions. Its a defective piece..
Any suggestons would be appritated. It has 2 batteries, 1 in touch panel and the other in key board.If you have a fairly new Mac...
You are still under warranty. Call Apple Care. Make sure you get a case number as all repairs have an additional 90 days of warranty.
#1 - You have 14 days from the date of purchase to return your computer with no questions asked.
#2 - You have 90 days of FREE phone tech support.
#3 - You have the standard one year Apple warranty.
#4 - If you've purchased an AppleCare Protection Plan, your warranty last for 3 years. You can obtain AppleCare anytime up to the first year of the purchase of your computer.
Take FULL advantage of your warranty. Posting on a message board should be done as a last resort and if you are out of warranty or Apple Care has expired. -
When I use Siri, my screen goes blank and the apple logo appears and disappears. I've reset it, but problem still occurs. How can I fix this?
Did you reset your iPad like this: Press and hold the Home and Sleep buttons simultaneously until the Apple logo appears. Let go of the buttons and let the device restart.
-
What could be wrong with my iMac? When switched on the screen displays the apple logo with a busy bar at the bottom of the screen. This displays the progress of the computer trying to do something. To fill the bar takes about 30 mins and then switches off
Which OS X is installed?
-
When i press power button i hear several click sounds before start up?
When I press power button I hear several click sounds before start up begins. Shortly after Apple logo appears it clicks off.
Which MacBook Pro do you have? If it has an optical drive then that is just the optical drive checking if there is a disk inserted.
-
I dropped my iphone 5 in the water, its dead and when I try to charge it the apple logo comes and goes, thats my only sign of life, I've done many after market repairs but what I want to know is if I should replace the ligntning port or the battery... or just buy a galaxy s5?
If you dropped it in water, and then plugged it in, you may very well have destroyed the battery and/or the logic board. Charging/plugging in to a power source is very damaging to wet electronic devices. There is not much you can do but replace the entire iPhone...and since you did repairs yourself Apple will not do an out-of-warranty replacement.
You can try replacing the battery, the lightning port is another issue, but I would not expect that iPhone to work again. -
Have plugged it into my pc as well and nothing happens except that.
Hold down power and home till it restarts and release after seeing the apple logo.
Still won't start? You can put it in recovery mode by holding power and home for 10 seconds and release only power after 10 seconds but keep holding home till iTunes recognizes your phone on recovery mode and restore iphone. -
I just turn my MacBook Pro on after charging it and the mouse was not responding,after carefully closing the it the power went off and not turning on again,really frustrating
Hello Kimo12,
The article linked below provides some useful troublehsooting steps that can help get your Mac powered back on.
Troubleshooting: My computer won't turn on
http://support.apple.com/kb/TS1367
Cheers,
Allen -
White screen during booting up then after few seconds turned off
Hi All, Please help me out. I uninstall itunes in my MBP using one application called AppZapper. I then wanted to restart the MBP but the computer unable to restart to the OS. It just shows a white screen with an Apple logo and progressing icon, then after few seconds it shut down by itself. I am so sad. Please help me. Thanks
II'm having the same problem, except I've not installed anything new.
AS soon soon as I power on my MacBook Pro ( running OS Maverick ) it boots up for two minutes and powers itself off suddenly. All I see is the white screen with the Apple logo and a bar underneath indicating the upload progress. -
Hi
I have recently bought a white iPhone 4S on Tuesday, and it has been repeatedly loosing all connection and just suddenly switching off.
When this happens I am unable to turn the phone back on again without a power source plugged into it. When I try to remove the phone from the power source it goes completely dead again.
However, the most recent time this has happened (today), as soon as I returned home the phone had no problem starting up as normal when I pressed the power button.
The signal was working fine even though it says 'searching' in the left hand top corner of the screen. I am wondering if my WIFI at home is influencing the phone to work inside the household?
This is a problem that needs to be sorted out ASAP because the phone is not working the majority of the time when I need it to.
Please if you have any suggestions or know the cause of this problem inform me straight away.
Would be much appreciated.
Thank you.Try connecting it to your iTunes library in Recovery Mode and restoring it. See this article for help on getting your iPod into Recovery Mode.
http://support.apple.com/kb/ht1808
B-rock -
I have an ipad 1 and all was fine until the other day and now I can't connect to itunes a box pops up saying cannot allocate memory, what does this mean and howdo I fix it
Try quitting all apps and restart your iPad. Maybe you are running out of memory on the iPad. It's worth a try.
Go to the home screen first by tapping the home button. Quit/close open apps by double tapping the home button and the task bar will appear with all of you recent/open apps displayed at the bottom. Tap and hold down on any app icon until it begins to wiggle. Tap the minus sign in the upper left corner to close the apps. Restart the iPad.
Restart the iPad by holding down on the sleep button until the red slider appears and then slide to shut off. To power up hold the sleep button until the Apple logo appears and let go of the button.
Or try a reset,
Reset the iPad by holding down on the sleep and home buttons at the same time for about 10-15 seconds until the Apple Logo appears - ignore the red slider - let go of the buttons. -
Hi all,
I need help with my iphone4s.
When I turn on my iphone4s, the apple logo will show for a few seconds, and it will suddenly fade off to a blank screen, and not start up. It will then restart by itself, and the cycle repeats. Any suggestions on how I can troubleshoot this problem?
What seems to be the problem here?
thanks and regards
WanWanlucg wrote:
When I turn on my iphone4s, the apple logo will show for a few seconds, and it will suddenly fade off to a blank screen, and not start up. It will then restart by itself, and the cycle repeats.
Make sure you have the Current Version of iTunes Installed on your computer
iTunes free download from www.itunes.com/download
Then See Here > http://support.apple.com/kb/HT1808
You may need to try this More than Once... Be sure to Follow ALL the Steps...
Take your time... Pay particular attention to Steps 3 and 4.
After you have Recovered your Device...
Re-Sync your Content or Restore from the most recent Backup...
Restore from Backup > http://support.apple.com/kb/ht1766 -
Im having major problems syncing my iphone 4 to itunes, this problem started after upgrading to ios 5. I have upgraded my itunes, turned sync by wifi on and off but still nothing. Everytime I try to sync my iphone it just says sync cancelled. Please help.....
I'm having the same problem ! Each time the sync starts it suddenly stops and says finished syncing
-
My Imac doesnt start after de pasword, It continuos asking for it again and again, what can I do to start it?
First, make sure caps lock is not on.
Another reason why your password might not be recognized is that the keyboard layout (input source) has been switched without your realizing it. At the login screen, you can cycle through the available layouts by pressing the key combination command-space or command-option-space. See this support article.
If the user account is associated with an Apple ID, and you know the Apple ID password, then maybe the Apple ID can be used to reset your user account password.
Otherwise*, start up in Recovery mode. When the OS X Utilities window appears, select
Utilities ▹ Terminal
from the menu bar at the top of the screen—not from any of the items in the OS X Utilities window.
In the window that opens, type this:
res
Press the tab key. The partial command you typed will automatically be completed to this:
resetpassword
Press return. A Reset Password window opens. Close the Terminal window to get it out of the way.
Select your startup volume ("Macintosh HD," unless you gave it a different name) if not already selected.
Select your username from the menu labeled Select the user account if not already selected.
Follow the prompts to reset the password. It's safest to choose a password that includes only the characters a-z, A-Z, and 0-9.
Select
▹ Restart
from the menu bar.
You should now be able to log in with the new password, but your Keychain will be reset (empty.) If you've forgotten the Keychain password (which is ordinarily the same as your login password), there's no way to recover it.
*Note: If you've activated FileVault, this procedure doesn't apply. Follow instead these instructions.
Maybe you are looking for
-
Use Camera RAW with Sony Nex-3
Hey Guys! I want to get out more details from my photos. Im using Adobe Photoshop CS5 Sony NEX-3 Compact Camera (listed in the camera raw compatibility list) First i changed the cameras picture format from jpg to RAW & made some photos. At home i tri
-
Why is text become blurry and out of focus?
Why is text become blurry and out of focus?
-
How do I get the student's answers to show on the next slide for drag and drop interaction?
I'm working with Captivate 7 on a computer running Windows 8. I created a simple, one-to-one drag and drop activity using the Drag and Drop Wizard. I want the student's answers to show on the next slide. Specifically, I want the drop source to show
-
Installing : error reading businessobjects.msi
Hi Gurus I am installing Business Objects Edge Series ( evaluation version). while installing it gives error "Error in reading BusinessObjects.msi file is missing or corupted " . while file is in place and its size is 15.8 MB. I have done the install
-
In order to use the flv progressibe download, you have to put the flv out on the server in its final location first, then build your movie. After doing so, I tested the URL and all is well. After makinga web service , then a portlet, the portal appea