Cannot connect using Accessing the Router's Web-Based

I'm trying to update firmware, I have done all the step to access the router's web-based.. I connected DSL to the Ethernet port on the router, from the router I used another Ethernet cable to connect the router to my laptop.. I can't get an internet connection.  The reason why I'm doing the update I have been using WRT54G2 V1 with no problems, all at once I can't connect to the internet using the router.  I was told that I need to perform a firmware update.
Thank you for the help

What' s the ip address and the default gateway are you getting on the computer ?
Connect the DSL modem to the Internet port of the router then use port number one on the router to connect the computer.
Click on Start > Run > type CMD hit Enter command promt window will appear on the screen.
In the command promt window tupe "ipconfig" hit Enter. Now you will see the ip address and the default gateway on the screen. Use the default gateway to open the setup page of the router.

Similar Messages

  • WRT54GX4 - Difficulties Accessing the Router's Web-Based Setup Page

    WRT54GX4 - Difficulties Accessing the Router's Web-Based Setup Page.
    I have tried everything posted to the forums and the Knowledge Base for several weeks now with no luck.  I can power push router and gain access to router's web-base interface but only for a few minutes than it quits loading part way through and or does not load at all.  If I turn off the wireless side I can access the router at will with no problems. My warranty is almost over. I am at my wits end. I would like to get it replaced under warranty if I can. (^8
    Solved!
    Go to Solution.

    Thank you for your recommendations peanuts. (^8
    I bought the router back in December 10, 2006. 
    I updated the firmware to v1.00.20 back in June 2007. After I did a successful firmware upgrade I reset the router to factory default settings and then reconfigured it. It has worked Ok till a couple of months ago.
    I have read everything I can find here on the support forum and in the Knowledge Base several times.
    I have tried changing all the different settings to the different recommendations posted here and in Knowledge Base with no success. Each time I would do a long reset back to factory defaults, let it soak for a few hours and then make one change at a time and let it soak.
    I have been monitoring 6 other wireless AP(s) around me (none mine) for a couple of months too. None of them are strong enough to connect to. My SSID is different from them. I have tried all the channels. My router is passworded and MAC'd.
    It is looking like it is time to call support and try to get a replacement under warranty while it is still in affect.

  • Unable to access the Router's Web-Based Setup Page

    Hey, I found a little problem when I tried to change the configurartions to my Linksys WRT54GS ver- 6.0 router. Problem is that I can not acces to setup, nor can I connect to Internet trough wire. Can somebody help me with my problem?
    Pasi

    To view the router's web pages:
    You do not need an Internet connection. The router's "web pages" are built into the router.
    Use Internet Explorer, it usually works.
    JavaScript must be enabled.
    Use a computer that is wired to the router.
    In the non-working computer, temporarily turn off your software firewall.
    Point your browser to 192.168.1.1 , then login to your router. Your user name should be left blank. Your password is "admin" (with no quotes), unless you changed it.
    If you are using Zone Alarm, right click on the ZA icon in the system tray (lower right corner of screen) and then click "Shutdown ZoneAlarm", and see if this fixes your problem. If this does not work, try the following with Zone Alarm: Open the ZAISS control center, go to Privacy, then temporarily turn off Ad Blocking and Cookie Control, and see if that fixes your problem.
    If you are using Noton Internet Security with the Add-on Pack, be sure to turn off the Pop-up Blocker, and the Ad blocker. Some users have reported that they needed to uninstall the entire Norton Add-on Pack.
    If you cannot get anything at 192.168.1.1 then perhaps this is not your router's address. Go to "Start" > All Programs > Accessories > Command Prompt.
    A black DOS box will appear. Type in "ipconfig" (with no quotes), then hit the Enter key. Look at the "Default Gateway". Is it 192.168.1.1 ? Point your browser to the "Default Gateway", then login to your router.
    If the above fails, disconnect your modem from the router, and try again. If this corrects your problem, then most likely you have a "modem-router" rather than an ordinary modem. Report back with this problem, and also state the make and exact model number of your modem (not the router).
    If all of the above fails, power down your entire system, unplug it from the wall, wait one minute, then power up and try again.
    If all of the above tips fail, then reset the router to factory defaults: Power down the router and disconnect all wires from it. Wait one minute. Power up the router, allow it to fully boot (1-2 minutes), then press and hold the reset button for 30 seconds, then release the button and allow the router to reset and reboot ( 2-3 minutes). Power down router. Wait one minute. Connect one computer, by wire, to a LAN port on the router. Boot up system. It should work.
    If the reset does not fix your system, then you need to download and install (or re-install) the latest firmware for your router. After the firmware upgrade, you must reset the router to factory defaults, then setup the router again from scratch. If you saved a router configuration file, DO NOT use it.

  • WET 610N Cannot Connect after Replacing the Router

    Hello,
    WET610 has been working flawlessly with the old router.  Upon replacing the router however, I tried to set it up as was before by using the CD that came with WET610N.  I keep gettin the error 107.
    I would appreciate any and all suggestions.  Thank you all in advance.

    I’m not that familiar with error 109 but I believe it has something to do with the setup cd being corrupted. Good thing is that there is an option to setup the bridge manually. These links will guide you on how to setup the bridge manually: Manually configuring a Linksys Wireless-N Bridge to work with an access point and Configuring a Linksys Wireless-N Bridge through the web-based setup page. Before reconfiguring the settings of the bridge, make sure that the bridge has been reset to factory default settings (push and hold the reset button for 30 seconds then power it off for another 30 seconds; once the power light is solid, you can start the manual configuration).
    Other links for WET610N:
    WET610N Frequently Asked Questions
    What is a wireless bridge and how to use it

  • Need access the E1000's web-based setup page.

    I have a Linksys E1000 wireless router, and I seem to have either written down the password incorrectly or am using the wrong one. Regardless, I can not access the web-based setup for the router. Is there anyway to reset the username and password for it?
    Solved!
    Go to Solution.

    Yes, there is.  You'll have to reset the router back to defaults, which will reset the password back to the default password for your router.  Unfortunately , you'll also have to reconfigure the settings, since all settings go back to factory default.  Just hold press the recessed "reset" button for your router for about 30 seconds, then release it.  After the router has re-initialized itself, you'll be able to log in to the web GUI again with the default password.

  • WRT54GL - Cannot access the router

    I can't access the router "WRT54GL" from 192.168.1.1.
    I don't know username and password.
    Could you help me please?

    Before I suggest you for any troubleshooting steps. I would like to know few questions. Let me know the IP address from the router? Here are the steps to check the IP address.
    You can check the IP address in the following manner:
    # Click on Start -> All Programs -> Accessories -> Command Prompt.
    # A black pop up box should come up, type: "ipconfig /all" …
    There check the IP address and Default Gateway under LAN….
    If the Default gateway is '192.168.1.1' then in case once reset the router... Steps to reset the router:
    Push the reset button on router for 30 seconds, turn off the router wait for 30 seconds and then power it on.
    Power light should blink when you perform the reset process.
    The default password is “admin” and you may leave the User name field blank.
    Here is the link for accessing the router's web -based setup page: http://www6.nohold.net/Cisco2/ukp.aspx?pid=93&login=1&vw=1&app=search&articleid=3676&userrole=Linksy...

  • Cannot connect using new modem

    My sister spilled water on my modem so I dug up this older Westell Model 2200 modem which works fine with my desktop. However, when I plug the modem to the router, I don't get any internet signal anymore. I tried reconnecting all wires, rebooted everything.
    Also when I try to hit up the router's web based setup, it leads me to the Modem's intead when I type in 192.168.1.1
    When I try running ipconfig, the windows pops up for a split second and then disappears.
    HELP PLEASE!
    Message Edited by fobsternd on 08-27-2008 08:08 PM

    Reset the router for few seconds ..... after reset .... try this settings .....
     Access the setup page of the router by launching an
    Browser and type on the address bar, 192.168.1.1 and press enter. When
    it prompts for the username and password, leave the username field
    empty and provide password as "admin" (Without quotes)
    click on ok.
    On the main setup page the ""Internet Connection Type"" should be
    on ""Obtain IP Automatically - DHCP “. Click on the Save Settings
    button.
    Now click on the sub tab ""MAC address clone"".
    - Click on enable
    Click Clone & click save settings
    Check WAN Ip on Status page of router ....
    If getting Valid Ip .... try going online
    If you are getting Ip - 192.168.1.X ...change the LAN Ip to 192.168.2.1 ....Power cycle for 3-4 minutes ...
    Try going online
    If still not working ...use Internet Connection type as PPPOE .... Use Username & Password provided by Service Provider ....
    Click save settings....
    Look for WAN IP address again under status page ....

  • Error in router's web-based setup page (WRT54G V5)

    Hi,
    My router’s web-based setup page is unable to load fully.
    There seems to be an error with some document.setup.save file.
    I have tried to reset my router but the router’s web-based setup page is still unable to load fully.
    Please help.
    Thanks.

    Try Internet Explorer, it usually works.
    JavaScript must be enabled.
    Temporarily turn off your computer's software firewall, and see if that corrects your problem.
    Hope this helps.

  • Need help accessing the router web page.  I have been tol...

    Need help accessing the router web page.  I have been told my router is acting like a switch and the IP address is not in the proper range.  I have tried reseting the router (hold for 30 sec and unplug for 5 mins).  Didn't work.
    thanks

    What router are you using?  Almost all Linksys routers use 192.168.1.1 as the default local IP address, but there is at least one that uses 192.168.16.1 , namely the WTR54GS  (not the WRT54GS).
    You need to try again to reset the router to factory defaults.
    To reset your router to factory defaults, use the following procedure:
    1) Power down all computers, the router, and the modem, and unplug them from the wall.
    2) Disconnect all wires from the router.
    3) Power up the router and allow it to fully boot (1-2 minutes).
    4) Press and hold the reset button for 30 seconds, then release it, then let the router reset and reboot (2-3 minutes).
    5) Power down the router.
    6) Connect one computer by wire to port 1 on the router (NOT to the internet port).
    7) Power up the router and allow it to fully boot (1-2 minutes).
    8) Power up the computer (if the computer has a wireless card, make sure it is off).
    9) Try to ping the router. To do this, click the "Start" button > All Programs > Accessories > Command Prompt. A black DOS box will appear. Enter the following: "ping 192.168.1.1" (no quotes), and hit the Enter key. You will see 3 or 4 lines that start either with "Reply from ... " or "Request timed out." If you see "Reply from ...", your computer has found your router.
    10) Open your browser and point it to 192.168.1.1. This will take you to your router's login page. Leave the user name blank (note: a few Linksys routers have a default user name of "admin" (with no quotes)), and in the password field, enter "admin" (with no quotes). This will take you to your router setup page. Note the version number of your firmware (usually listed near upper right corner of screen). Exit your browser.
    If you get this far without problems, try the setup disk (or setup the router manually, if you prefer), and see if you can get your router setup and working.
    If you cannot get "Reply from ..." in step 9 above, your router is dead.
    If you get a reply in step 9, but cannot complete step 10, then either your router is dead or the firmware is corrupt. In this case, use the Linksys tftp.exe program to try to reload your router with the latest firmware. After reloading the firmware, repeat the above procedure starting with step 1.
    If you need additional help, please state your ISP, the make and model of your modem, your router's firmware version, and the results of steps 9 and 10. Also, if you get any error messages, copy them exactly and report back.
    Please let me know how things turn out for you.
    Message Edited by toomanydonuts on 01-21-2008 04:40 AM

  • I recieved the following message when I connect my device to teh computer: This Ipod cannot be used because the apple mobile device service is not started.  What's wrong?

    I recieved the following message when I connect my device to the computer: This Ipod cannot be used because the apple mobile device service is not started.  What's wrong?

    http://support.apple.com/kb/TS1567
    There have been some problems accessing pages on the Apple web site.  If the hyperlink gives you a "We're sorry" message, try again.

  • Everytime I connect my iPod to USB, iTunes says the following: This iPod cannot be used because the required software is not installed.  Run the iTunes installer to remove iTunes, then install the 64-bit version of iTunes.

    I have the latest 64-bit version of iTunes on Windows 7 Ultimate.  Everything was fine until recently.  Now when I connect my iPod Touch to the USB to sync with iTunes, I get the following message:  "This iPod cannot be used because the required software is not installed.  Run the iTunes installer to remove iTunes, then install the 64-bit version of iTunes"  I have removed, repaired, and installed the 64-bit version numerous times as well as disabled all antivirus / adware utilities.  Same message appears when I plug in my iPod.  Any help would be greatly appreciated.

    Did you try removing and reinstalling all the Apple software using these instructions:
    Removing and reinstalling iTunes, QuickTime, and other software components for Windows Vista or Windows 7

  • I have a new iPod touch and when I connect it to my pc and itunes, a window says "this ipod cannot be used because the Apple Mobile Device Service is not started."

    I have a new iPod touch and when I connect it to my pc and itunes, a window says "this ipod cannot be used because the Apple Mobile Device Service is not started."

    This might help restart it http://support.apple.com/kb/TS1567

  • I just got an iphone and am trying to connect it to my itunes account.  Getting the message " This iphone cannot be used because the Apple Mobile Device service is not started.  How do I start it?  Have already been back to the store with it and no change

    I just got an iphone and am trying to connect it to my itunes account.  Getting the message " This iphone cannot be used because the Apple Mobile Device service is not started.  How do I start it?  Have already been back to the store with it and no change.

    http://tinyurl.com/3hs3g2u

  • I restored my iPhone 3 g to its factory settings and I tryed to connect it to iTunes on my laptop and it said This iPhone cannot be used because the required software is not installed. Run the installer to remove iTunes. Then install iTunes again. HELP!!

    I restored my iPhone 3 g to its factory settings and I tryed to connect it to iTunes on my laptop and it said This iPhone cannot be used because the required software is not installed. Run the installer to remove iTunes. Then install iTunes again. HELP!! PLEASE!! Because I cannot get on my iPhone!!

    Hi, Mommacat26. 
    Thank you for visiting Apple Support Communities. 
    This usually means that a required component is missing.  Start with completely uninstalling iTunes and all of it's components in the order specified in the article below.  Once this is done, download and install iTunes.
    Removing and reinstalling iTunes and other software components for Windows Vista, Windows 7, or Windows 8
    http://support.apple.com/kb/HT1923
    Removing and Reinstalling iTunes and other software components for Windows XP
    http://support.apple.com/kb/ht1925
    If you receive any errors when uninstalling any components of iTunes, try the steps in the article below for each component that gives you an error.
    "The feature you are trying to use is on a network resource that is unavailable" alert appears when removing Apple software in Windows
    http://support.apple.com/kb/TS3704
    If the issue persists, try installing the Apple Mobile Device Support driver.  See the section labeled Verify that the Apple Mobile Device USB Driver is installed > For Windows XP or Vista, Windows 7, and Windows 8 > Update the Apple Mobile Device Driver.
    iOS: Device not recognized in iTunes for Windows
    http://support.apple.com/kb/TS1538
    Cheers,
    Jason H. 

  • Hi - a new and confusing message when I try to connect my iphone with itunes on my laptop:  "this iphone cannot be used because the Apple Mobile Device Service is not started".  Any idea of my way out of this cul-de-sac??  Brian

    Hi, I'm getting a new and confusing message when I connect my Ipad/phone to my laptop:  "This iphone cannot be used because the Apple Mobile Device Service  is not started" ... any idea, anyone, how I get out of this cul-de-sac.  Brian

    try this http://melchoi.wordpress.com/tag/this-iphone-cannot-be-used-because-the-apple-mo bile-device-service-is-not-started/
    Hope it's gonna help

Maybe you are looking for