Cannot establish wireless connection with WRT54G after power-off
My WRT54G (firmware v7.00.0) is connected to cable TV modem and
usually the wireless connection works fine, but after swiching off and later
on the power to WRT54G a laptop cannot establish WiFi connection to internet.
I can see in Odyssey software (for wireless communication) that my laptop
found the right network (SSID) but in status it says 'waiting for keys'.
I use WPA2 (TKIP). The laptop does not connect to internet.
When I connect it by cable (ethernet) the internet works fine, I have noticed
that by accessing the web-page utility of the router and simply clicking
save changes on wireless-settings page (without making any changes in
the settings) my laptop instantly establishes wireles connection and
everything works fine till next power swich-off.
Thanks for reply! I have my network in preffered, and the software/laptop locks on
the network (see it, says it have excellent signal strenght) and gives note
'waiting for keys' (the WPA2 encription key is in the settings - both of router and laptop client - Odyssey).
I've got firmware ver.7 so it is probably the latest.
Similar Messages
-
Cannot establish wireless connection with Macbook
I bought Belkin ADSL2+ Wireless 802.11g Modem Router recently and have problems connecting via Airport.
However, the signal for the Macbook is strong and generally, I could connect for about 10-15 seconds. Afterwhich, a dialog box that states that there is an error connecting to the wireless network appears and the connection disappears.
It should not be a modem problem as I could connect to the internet via wireless on my PC and can even connect to VPN with the same router.
What could be the likely problem? Please help.
Thanks!Thanks for reply! I have my network in preffered, and the software/laptop locks on
the network (see it, says it have excellent signal strenght) and gives note
'waiting for keys' (the WPA2 encription key is in the settings - both of router and laptop client - Odyssey).
I've got firmware ver.7 so it is probably the latest. -
Cannot establish wireless connection with printer
HP Photosmart C4780/Windows 7 64 bit/no error messages
This printer was previously running on this PC via a network router. I replaced the router with a new one and have not been able to reconnect the printer to the new network. The printer works when connected via the USB cable. The blue wireless light is ON on the printer panel.
Following the troubleshooting guidance of HP on line, I disconnected the USB cable and put in the printer install disk, hit launch pad/Configure Network Device which goes to a window "Reconfiguring Network Device". This runs for hours and never gives me the next step (never asks me to connect the USB cable).
I was able to print out a Printer Status Report when the printer was connected via the USB cable.
Thank you
CobiYou have to run the Wireless setup wizard from your printer to connect it to the network with your new router-
You will have to enter the SSID & WEP/WPA KEY
Although I work for HP, I am speaking for myself and not for HP.
Kudos! If you feel my post has helped you please click the White Kudos! Star just below my name : )
If you feel my answer has fixed your problem please click 'Mark As Solution' and make it easier for others to find help quickly : ) -
Adobeconnect outlook add-ins version 3.5 cannot establish the connection with the server
i am using outlook 2010 and i have installed the outlook add-ins ver3.5 to my laptop. i was trying to login the server through add-ins with my login details. But it popup"cannot establish the connection to server, please check your server address and account", the server i am using is "intercall-apac.adobeconnect.com". Just want to know is there any port should be opened on the firewall?
Try putting https:// in the URL for the server instead of http:// (or check the box for a secure connection)
-
ITunes cannot establish secure connection with server
Why am I not able to establish secure connection with server?
Hi,
We support IMAP (yahoo/gmail/hotmail), I apologize for the inconvenience.
Best regards,
Michelle -
Hiya!
This issue has been answered numerous times for Office 2010 and Office 2007, but I have yet to any solutions or Hotfixes that work for Office 2013 (x64) on Win7.
How to replicate the issue:
Open a file from a network share.
Edit file.
Leave computer on with file open. Computer goes to sleep or into stand-by mode.
Wait a bit
Wake up computer
CPU opens file in Read-Only mode and gives you the following error "Word cannot establish a network connection with this document after the system resumed from suspend mode. Save the document into a different file to keep any changes."
What I've tried:
http://support.microsoft.com/kb/2434898 - Office 2007 registry fixes. Does not apply.
http://support.microsoft.com/kb/2413659 - Office 2010 problem. This exact issue. Says 'No microsoft products that match this hotfix are installed'
Work Around:
I can saving new versions of these files overrides this issue, but this is sometimes not possible for end-users who only have specific access to ONE SPECIFIC FILE in a particular network share.
Please let me know how I can alleviate this issue!
Thanks
-ChrisHi,
Are those problematic documents created via previous versions of Office?
Please also try to run a repair of your Office 2013 installtion and check if it helps. See:
http://office.microsoft.com/en-in/excel-help/repair-office-programs-HA010357402.aspx
Regards,
Steve Fan
TechNet Community Support -
Cannot establish wireless connection
I installed a wireless g router (wrt54g) and it was working fine. Then I had some problems with my pc,,,and had to re-install windows and my linksys software. Now I cannot connect wireless. My router is working fine, but I have to keep the network cable connected between my laptop and port 1 of the router. It still tries to connect to my wireless network that was set up before(ryan). It is stuck on "aquiring network address. I get 0.00.00.0 for my ip addy the wireless network is using. I have tried to "repair" the wireless connection,,,and it freezes up and says it cannot renew my ip addy. I am connected to the internet just fine. I have tried the reset button on the back of my router. What am I not doing right? I cannot delete the wireless network from my windows that I was using before, and start all over which I thought would work. The router and my wireless network are not communicating with each other.
Im using windows xp, with the linksys wireless g 2.4GHz router. I have my cable modem, my laptop and my router. Not trying to add more pc's. Just tryin to turn my laptop back into wireless. Please help.When you pushed the reset button on your router you set it's configuration back to the factory defaults. Whatever settings you had originally modified on your router when you first set it up have been blown away. Since the router is now running on the original factory settings, you can easily get back into the router and reconfigure it. With your pc hardwired to one of the four ports on the back of the router, fire up your browser and enter 192.168.1.1 as the URL then press ENTER. It will prompt you for a username and password. Leave the username blank, enter the word admin for the password. Change the SSID field to whatever name you want to use for your wireless network. Sounds like you used 'ryan' before. If so, use that. If not, make something up other than 'linksys'. Make sure the SSID Broadcast option is ENABLED. Save the changes, reboot your router. Disconnect the network wire from your pc and reboot the pc. You should now be able to see your network, whatever you named the SSID. You should be able to connect to it. If you get the pc and the router talking wirelessly, you then want to think about going back into the router and setting up wirelss security to keep the rest of the world out. Read the router manual to see what the options are and how to go about doing it.
-
I cannot establish VPN connection with rv120w to shrew soft client
1. I bought 2 rv120w router and install one direct to WAN and one behind router-hub.
2. one behind router is set DMZ, and each are conneted Site to Site vpn
3. I need to connect each site with my mobile devices(1 notebook, 2 Win8 tablets, 2 android devices )
4. i use wibro mobile router, win8 devices're behind router, and their fort is fowarded(DMZ)
5. I'll take care of Android devices later, here now, my trouble is Win8 devices
6. i installed cisco QuickVPN software. frankly,that software is shit. i don't know why but it even cannot reach router, no log generated on rv120w. and i dont want PPTP connection. sorry for criticism but I'm sure many of QuickVPN users(and people who fail to be a user) agree with me. it's 2014. not 1998.
Cisco should be shamed for that software. it looks like a second grade collage student's 2nd semester project(Many of them're batter nowadays.) and doesn't work.
more amazing fact is that's only software that RV series provides officialy. What the...so in conclusion, Cisco does not provide any IPSec client connection tool at all. does that makes any sense?
7. i tried 10 or more hours to make IPSec client connection with many vpn client soft ware, this is my closest shot.
RV120W log :
2014-10-02 15:03:05: [rv120w][IKE] INFO: Configuration found for 175.xxx.xxx.xxx[500].
2014-10-02 15:03:05: [rv120w][IKE] INFO: Received request for new phase 1 negotiation: 11x.xxx.xxx.xxx[500]<=>175.xxx.xxx.xxx[500]
2014-10-02 15:03:05: [rv120w][IKE] INFO: Beginning Aggressive mode.
2014-10-02 15:03:05: [rv120w][IKE] INFO: Received Vendor ID: draft-ietf-ipsra-isakmp-xauth-06.txt
2014-10-02 15:03:05: [rv120w][IKE] INFO: Received unknown Vendor ID
2014-10-02 15:03:05: [rv120w][IKE] INFO: Received unknown Vendor ID
2014-10-02 15:03:05: [rv120w][IKE] INFO: Received Vendor ID: draft-ietf-ipsec-nat-t-ike-02
2014-10-02 15:03:05: [rv120w][IKE] INFO: Received unknown Vendor ID
2014-10-02 15:03:05: [rv120w][IKE] INFO: Received Vendor ID: RFC 3947
2014-10-02 15:03:05: [rv120w][IKE] INFO: Received unknown Vendor ID
2014-10-02 15:03:05: [rv120w][IKE] INFO: Received Vendor ID: DPD
2014-10-02 15:03:05: [rv120w][IKE] INFO: Received Vendor ID: DPD
2014-10-02 15:03:05: [rv120w][IKE] INFO: Received unknown Vendor ID
2014-10-02 15:03:05: [rv120w][IKE] INFO: Received unknown Vendor ID
2014-10-02 15:03:05: [rv120w][IKE] INFO: Received unknown Vendor ID
2014-10-02 15:03:05: [rv120w][IKE] INFO: Received Vendor ID: CISCO-UNITY
2014-10-02 15:03:05: [rv120w][IKE] INFO: Received unknown Vendor ID
2014-10-02 15:03:05: [rv120w][IKE] INFO: For 175.xxx.xxx.xxx[500], Selected NAT-T version: RFC 39472014-10-02 15:03:06: [rv120w][IKE] INFO: Floating ports for NAT-T with peer 175.xxx.xxx.xxx[4500]
2014-10-02 15:03:06: [rv120w][IKE] INFO: NAT-D payload does not match for 11x.xxx.xxx.xxx[4500]
2014-10-02 15:03:06: [rv120w][IKE] INFO: NAT-D payload does not match for 175.xxx.xxx.xxx[4500]
2014-10-02 15:03:06: [rv120w][IKE] INFO: NAT detected: Local is behind a NAT device. and alsoPeer is behind a NAT device
2014-10-02 15:03:06: [rv120w][IKE] INFO: Sending Xauth request to 175.xxx.xxx.xxx[4500]
2014-10-02 15:03:06: [rv120w][IKE] INFO: ISAKMP-SA established for 11x.xxx.xxx.xxx[4500]-175.xxx.xxx.xxx[4500] with spi:90dd9f6bf4d51d95:70f7c62456edef9e
2014-10-02 15:03:06: [rv120w][IKE] INFO: Received attribute type "ISAKMP_CFG_REPLY" from 175.xxx.xxx.xxx[4500]
2014-10-02 15:03:06: [rv120w][IKE] INFO: Login succeeded for user "fxxxxxxxxX1"
2014-10-02 15:03:06: [rv120w][IKE] INFO: Received attribute type "ISAKMP_CFG_REQUEST" from 175.xxx.xxx.xxx[4500]
2014-10-02 15:03:06: [rv120w][IKE] ERROR: Local configuration for 175.xxx.xxx.xxx[4500] does not have mode config
2014-10-02 15:03:06: [rv120w][IKE] WARNING: Ignored attribute 5
2014-10-02 15:03:06: [rv120w][IKE] ERROR: Local configuration for 175.xxx.xxx.xxx[4500] does not have mode config
2014-10-02 15:03:06: [rv120w][IKE] ERROR: Local configuration for 175.xxx.xxx.xxx[4500] does not have mode config
2014-10-02 15:03:06: [rv120w][IKE] ERROR: Local configuration for 175.xxx.xxx.xxx[4500] does not have mode config
2014-10-02 15:03:06: [rv120w][IKE] ERROR: Local configuration for 175.xxx.xxx.xxx[4500] does not have mode config
2014-10-02 15:03:06: [rv120w][IKE] WARNING: Ignored attribute 28678
2014-10-02 15:03:06: [rv120w][IKE] ERROR: Local configuration for 175.xxx.xxx.xxx[4500] does not have mode config
2014-10-02 15:03:06: [rv120w][IKE] ERROR: Local configuration for 175.xxx.xxx.xxx[4500] does not have mode config
2014-10-02 15:03:06: [rv120w][IKE] ERROR: Local configuration for 175.xxx.xxx.xxx[4500] does not have mode config
2014-10-02 15:03:06: [rv120w][IKE] ERROR: Local configuration for 175.xxx.xxx.xxx[4500] does not have mode config
2014-10-02 15:03:06: [rv120w][IKE] INFO: Purged ISAKMP-SA with proto_id=ISAKMP and spi=90dd9f6bf4d51d95:70f7c62456edef9e.
2014-10-02 15:03:07: [rv120w][IKE] INFO: ISAKMP-SA deleted for 11x.xxx.xxx.xxx[4500]-175.xxx.xxx.xxx[4500] with spi:90dd9f6bf4d51d95:70f7c62456edef9e
Phase 1 Setting
Selected IKE Policy View
General
Policy Name
FDCStD
Direction / Type
Responder
Exchange Mode
Aggresive
Enable XAUTH Client
Local Identification
Identifier Type
Local Wan IP
FQDN
112.167.xxx.xxx
Peer IKE Identification
Identifier Type
Remote Wan IP
FQDN
175.xxx.xxx.xxx
IKE SA Parameters
Encryption Algorithm
3DES
Authentication Algorithm
SHA-1
Authentication Method
Pre-Shared Key
Pre-Shared Key
qpwoeiruty
Diffie-Hellman (DH) Group
Group 2 (1024bit )
SA-Lifetime
28800 Seconds
Phase2 setting
Add / Edit VPN Policy Configuration
Policy Name
Policy Type
Auto Policy Manual Policy
Remote Endpoint
IP Address FQDN
NETBIOS
Enable
Local Traffic Selection
Local IP
Any Single Range Subnet
Start Address
End Address
Subnet Mask
Remote Traffic Selection
Remote IP
Any Single Range Subnet
This field is not editable, because netbios is selected.
Start Address
End Address
Subnet Mask
Split DNS
Split DNS
Enable
Domain Name Server 1
Domain Name Server 2
(Optional)
Domain Name 1
Domain Name 2
(Optional)
Manual Policy Parameters
SPI-Incoming
SPI-Outgoing
Encryption Algorithm
3DES None DES AES-128 AES-192 AES-256 AES-CCM AES-GCM
Key-In
Key-Out
Integrity Algorithm
SHA-1 SHA2-256 SHA2-384 SHA2-512 MD5
Key-In
Key-Out
Auto Policy Parameters
SA-Lifetime
Seconds KBytes
Encryption Algorithm
3DES None DES AES-128 AES-192 AES-256 AES-CCM AES-GCM
Integrity Algorithm
SHA-1 SHA2-256 SHA2-384 SHA2-512 MD5
PFS Key Group
Enable
DH-Group 1 (768 bit) DH-Group 2 (1024 bit) DH-Group 5 (1536 bit)
Select IKE Policy
FDCStSFKS FDCStD
Shres client setting
Phase 1 Setting
Selected IKE Policy View
General
Policy Name
FDCStD
Direction / Type
Responder
Exchange Mode
Aggresive
Enable XAUTH Client
Local Identification
Identifier Type
Local Wan IP
FQDN
112.167.xxx.xxx
Peer IKE Identification
Identifier Type
Remote Wan IP
FQDN
175.xxx.xxx.xxx
IKE SA Parameters
Encryption Algorithm
3DES
Authentication Algorithm
SHA-1
Authentication Method
Pre-Shared Key
Pre-Shared Key
qpwoeiruty
Diffie-Hellman (DH) Group
Group 2 (1024bit )
SA-Lifetime
28800 Seconds
Phase2 setting
Add / Edit VPN Policy Configuration
Policy Name
Policy Type
Auto Policy Manual Policy
Remote Endpoint
IP Address FQDN
NETBIOS
Enable
Local Traffic Selection
Local IP
Any Single Range Subnet
Start Address
End Address
Subnet Mask
Remote Traffic Selection
Remote IP
Any Single Range Subnet
This field is not editable, because netbios is selected.
Start Address
End Address
Subnet Mask
Split DNS
Split DNS
Enable
Domain Name Server 1
Domain Name Server 2
(Optional)
Domain Name 1
Domain Name 2
(Optional)
Manual Policy Parameters
SPI-Incoming
SPI-Outgoing
Encryption Algorithm
3DES None DES AES-128 AES-192 AES-256 AES-CCM AES-GCM
Key-In
Key-Out
Integrity Algorithm
SHA-1 SHA2-256 SHA2-384 SHA2-512 MD5
Key-In
Key-Out
Auto Policy Parameters
SA-Lifetime
Seconds KBytes
Encryption Algorithm
3DES None DES AES-128 AES-192 AES-256 AES-CCM AES-GCM
Integrity Algorithm
SHA-1 SHA2-256 SHA2-384 SHA2-512 MD5
PFS Key Group
Enable
DH-Group 1 (768 bit) DH-Group 2 (1024 bit) DH-Group 5 (1536 bit)
Select IKE Policy
FDCStSFKS FDCStD
Shres client setting
8. in rv120w setting for advanced seup> Policy Type>
there's two option FQDN and IP Adress
when I'm in none static IP Adress environment, how should I set that field?
RV120w do not support none static IP Adress?Hi kastwf001,
My name is Mehdi from Cisco Technical Support, just want to inform you regarding QuickVPN is an light software using IPsec service of windows, so here it depend of windows and firewall ... IPsec setting on windows, encryption ...
anyhow for RV120W it's open for 3rd party software as ShrewVPN , TheGreenBow ... and working as expected since those software are using their ip sec services ..
Please follow configuration steps on RV120W and ShrewVPN (screenshots taken from you post) :
Please let me know if you have any question
Please rate the post or mark as answered to help other Cisco Customers
Regards
Mehdi -
After authentication, the connection is reset and the page fails to load. Or, it takes a very long time to establish the session. Earlier versions of ffx didn't have this problem and IE access these site just fine at the same time when ffx fails.
I had the exact problem. It seems when connecting from firefox i was getting directed to onlineeast2 and then the connection would reset. When connecting from IE i was getting directed to onlineeast3 and the connection was fine. So I edited my hosts file to force onlineeast2 to resolve to the ip address of onlineeast3. This is working for me. here is what i put in my hosts file:
171.159.66.159 onlineeast2.bankofamerica.com
171.159.66.159 onlineeast3.bankofamerica.com
The hosts file can be found here:
C:\WINDOWS\system32\drivers\etc\hosts -
Establishing a connection with Facebook on my BRAND NEW iMac
I cannot get the Facebook page to open. Safari tells me that it cannot establish a connection with facebook.com! What is up with this. I have a brand new iMac! How do I fix this?
Are "Parental Controls" set to block Facebook?
-
I cannot open my Yahoo Mail but everything else is OK. When I click Yahoo Mail Icon, I get this error message "Safari Cannot open this page. Safari can not establish secure connection with Yahoo Mail.
It sounds as though a script on the site, or an advertisement, is not working quite right...
When you have a problem with one particular site, a good "first thing to try" is clearing your Firefox cache and deleting your saved cookies for the site.
(1) Bypass Firefox's Cache
Use Ctrl+Shift+r to reload the page fresh from the server.
(You also can clear Firefox's cache completely using:
orange Firefox button ''or'' Tools menu > Options > Advanced
On the Network mini-tab > Cached Web Content : "Clear Now")
(2) Remove the site's cookies using either of these. Save any pending work first.
While viewing a page on the site:
* right-click and choose View Page Info > Security > "View Cookies"
* Alt+t (open the classic Tools menu) > Page Info > Security > "View Cookies"
Then try reloading the page. Does that help? -
Any suggestions on retreiving wireless connection with airport extreme, have unlugged power to all sources and pressed reset button on router, still amber flashing light
Hello ebulloc,
It sounds like you are getting the flashing amber colored light and cannot connect to the internet with it. According to this article:
AirPort base stations: About AirPort base station status lights (LED)
http://support.apple.com/kb/ht4600
Flashing amber
Startup is complete, but the Wi-Fi base station has detected a condition that requires your assistance. To resolve flashing amber status light conditions click here to learn more. Launch AirPort Utility to find out what conditions are being reported.
This article should lead you to a resolution:
Wi-Fi base station: Understanding and resolving a blinking amber status light
http://support.apple.com/kb/TS1589
Thank you for using Apple Support Communities.
Take care,
Sterling -
WRT350N: Vista cannot get wireless connection
I recently got a laptop to use on a wireless connection to my WRT350N. When I first set it up, it easily got a wireless connection to the WRT350N. After a few weeks of reliable wireless operation, the wireless connection would occasionally disconnect without warning or any apparent reason. I was usually able to reconnect fairly quickly until a couple of days ago. From that point on, reconnection was not assured. I switched the wireless mode on the WRT350N from mixed to one of the other options and got my last successful connection. Soon after that, the wireless connection dropped again and I've never been able to reconnect since, no matter what settings I specify. Windows Vista sees other wireless networks available (from neighbors' homes), but does not see my WRT350N even when sitting right next to it.
I've tried the EasyLink Advisor and it just says: "EasyLink Advisor could not establish a wireless connection to the Router." That's not very helpful. How can I restore a wireless connection from my laptop to the WRT350N?
Message Edited by tocumen on 09-04-2007 01:19 AMThanks, Helm, for your reply. Before seeing your reply, I called Linksys tech support and we got it working again. Basically, they had me clear the list of wireless connections under "manage wireless networks" in Vista. They had me change the security settings from PSK2 Personal and enter a new key. With that, I was able to get a wireless connection again. I told the tech that I preferred to stick with PSK2. So I switched back while he was still on the phone and got a successful wireless connection with PSK2. He suggested that my loss of connection in the first place was caused by the key being changed under PSK2 / AES and it was related to the key renewal period. It wasn't clear how to avoid encountering the trouble again. But at least I know how to recover from it should it happen again.
-
Unstable WPA connection with WRT54G 2.2 (firmware 4.30.5)
Hello everybody,
I'm experiencing some unstability in my wireless connection with my WRT54G router.
By the past, the router was working perfectly. Last week I've upgraded the firmware to the version 4.30.5. Since then I have to power off the router every morning to connect my Centrino laptop to it.
FYI, my router is a WRT54G model 2.2. I'm using Mixed Mode (B+G) + WPA2 Personal (TKIP+AES) with a Group Key Renewal = 3600 seconds. My router is using the wifi channel 4 and there is no other access point on this channel. On my laptop, I'm running a Windows XP SP2 with the latest system patches.
Please also note that my router is now identifying itself as a WRT54GL (in its web pages) and not just WRT54G. Not sure if it's an issue or not.
Any help will be greatly appreciated.
Thank you in advance,
PatrickMessage Edited by pbateman on 11-07-200601:54 AMYou mean that on the setup page of the router its says WRT54GL instead of the actual model?
When you try to turn off your router are you still wilrelessly connected?
"Give them nothing... But take from them everything..."
-Leonidas "300" -
Hello, I have a sql 2005 server, and I am a developer, with the database on my own machine. It alwayws works for me but after some minutes the other developer cant work in the application
He got this error
Login failed for user ''. The user is not associated with a trusted SQL Server connection. [CLIENT: 192.168.1.140]
and When I see the log event after that error, it comes with another error.
SSPI handshake failed with error code 0x8009030c while establishing a connection with integrated security; the connection has been closed. [CLIENT: 192.168.1.140]
He has IIS5 and me too.
I created a user on the domain called ASPSYS with password, then in the IIS on anonymous authentication I put that user with that password, and it works, on both machines.
and in the connection string I have.
<add key="sqlconn" value="Data Source=ESTACION15;Initial Catalog=GescomDefinitiva;Integrated Security=SSPI; Trusted_Connection=true"/>
I go to the profiler, and I see that when he browses a page, the database is accesed with user ASPSYS, but when I browse a page, the database is accesed with user SE\levalencia.
Thats strange.
The only way that the other developer can work again on the project is to restart the whole machine. He has windows xp profession, I have windows 2000.
If you want me to send logs please tellmeWell here's my problem, maybe you can help. Intermittenly I get a login failed when connecting to a db engine through Server Management Studio using Windows authentication. When this happens the following entries are generated on the server's application event log:
Event Type: Error
Event Source: MSSQLSERVER
Event Category: (4)
Event ID: 17806
Date: 1/14/2009
Time: 10:41:31 AM
User: N/A
Computer: <server name>
Description:
SSPI handshake failed with error code 0x8009030c while establishing a connection with integrated security; the connection has been closed. [CLIENT: <ip address>]
Event Type: Failure Audit
Event Source: MSSQLSERVER
Event Category: (4)
Event ID: 18452
Date: 1/14/2009
Time: 10:41:31 AM
User: N/A
Computer: <server name>
Description:
Login failed for user ''. The user is not associated with a trusted SQL Server connection. [CLIENT: <ip address>]
I've already ensured that the server is set to mixed authentication mode. Oddly enough, the workaround that I've found is that if I remote desktop into the server, log in and then log back out, Management Studio is suddenly able to connect again. No idea why it works.
As I said before, it is intermitten. Some days it errors on login, other days it doesn't and there are no configuration changes between them. Also, both client and server are in the same domain and same site so there is no VPN or anything in between. I'm really quite stumped. Any help would be great, or if you can point me in the right direction of where to look. Thank you in advance!
Maybe you are looking for
-
Connecting Air to external monitor (Dell)
I am trying to help my boss connect his Air (2010 edition) to an old Dell monitor we have here at the office. I bought a Mini DisplayPort to VGA Adapter but when we connected everything his Mac screen didn't appear on the Dell. Is there something els
-
How to Copy the specific record of one table to other table(same structure)
Hello, i have develop a form and some buttons on it. Suppose that Form is based on TABLE_1, which has the fiollowing structure. ( Bill_No Number(5), Bill_Date Date, Bill_amount Number(6), Description Varchar2(60) My requirement is when i save the any
-
Hi all, I have some bad fund in my cube. So to correct these bad funds, I am using function exit in BPS. My question is: Do I need to implement the initialization function and exit function both. how could I write these function modules. does anybody
-
Every Version AF TER 11.2.202.233 is not working.
Hi there it makes me very Angry to see and notice that EVERY BETA/OFFICIAL Version after 11.2.202.233 is not working with Firefox on EVERY VERSION of Firefox-. But can u explain me WHY is working 11.2.202.233 Version of Flash like it should (PERFORMA
-
Hi all, I have to do a business study for an implementation project,,, can anyone tell me where can i get the details of ASAP methodology. regards, urendra [email protected]