Cat0-3750 upgrade. Error: system number 1 does not support the same feature

I am trying to upgrade or rather downgrade from ipadvservices (inadvertently upgraded to) to ipservices on a stack of Cat-3750s, but I get the following error message:
Ios Image File Size: 0x00877A00
Total Image File Size: 0x00B04200
Minimum Dram required: 0x08000000
Image Suffix: ipservicesk9-122-37.SE1
Image Directory: c3750-ipservicesk9-mz.122-37.SE1
Image Name: c3750-ipservicesk9-mz.122-37.SE1.bin
Image Feature: IP|LAYER_3|PLUS|SSH|3DES|MIN_DRAM_MEG=128
Error: The image in the archive which would be used to upgrade
Error: system number 1 does not support the same feature set.
Any ideas?
Chris

I was having the same issue even with entering the following:
archive download-sw /overwrite /allow-feature-upgrade tftp://172.18.108.26/c3kx-sm10g-tar.150-2.SE7.tar
I noticed the image which was running on the switch was correct without the ".bin" at the end:
3560#sh ver | i image
System image file is "flash:c3560e-universalk9-mz.150-2.SE7"
I uploaded a fresh IOS image from CCO and made sure the image name had ".bin" at the end. Seems trivial except the error is produced through a sanity check. See below (please excuse the extra unplugging in the output):
3560#sh ver | i image
System image file is "flash:c3560e-universalk9-mz.150-2.SE7.bin"
3560#$de tftp://172.18.108.26/c3kx-sm10g-tar.150-2.SE7.tar
Loading c3kx-sm10g-tar.150-2.SE7.tar from 172.18.108.26 (via Vlan1): !!!!!!!!!!!!!!!!!!!!!!!!!!!!!!!!!!!!!!!!!                             !!!!!!!!!
Mar 30 01:33:35.480: %USBFLASH-5-CHANGE: usbflash0 has been removed!!!!!!!!!!!!!!!!!!!!!!!!!!!!!!!!!!!!!!
Mar 30 01:34:15.636: %PLATFORM_ENV-1-FRU_PS_ACCESS: FRU Power Supply is not responding!!!!!!!!!!!
[OK - 24893440 bytes]
Loading c3kx-sm10g-tar.150-2.SE7.tar from 172.18.108.26 (via Vlan1): !!!
Mar 30 01:34:35.593: %PLATFORM_ENV-6-FRU_PS_OIR: FRU Power Supply 2 removed!!!!!!!!!!!!!!!!!!!!!!!!!!!!!!!!!!!                             !!!!!!!!!!!!!!!!!!!!!!!!!!!!!!!!!!!!!!!!!!!!!!!!!!!!!!!!!!!!
examining image...
extracting info (100 bytes)
extracting c3kx-sm10g-mz.150-2.SE7/info (499 bytes)
extracting info (100 bytes)
System Type:             0x00010002
Ios Image File Size:   0x017BDA00
Total Image File Size: 0x017BDA00
Minimum Dram required: 0x08000000
Image Suffix:          sm10g-150-2.SE7
Image Directory:       c3kx-sm10g-mz.150-2.SE7
Image Name:            c3kx-sm10g-mz.150-2.SE7.bin
Image Feature:         IP|LAYER_3|MIN_DRAM_MEG=128
FRU Module Version:    03.00.78
Updating FRU Module on switch 1...
Updating FRU FPGA image...
FPGA image update complete.
All software images installed.
Worked for me, hope this helps.

Similar Messages

Installed graphics card does not support the opengl features recommended

I've installed FCP6 on my PowerMac (PPC G4 DP 1.25GHz), and when I run it, I get a warning ("...installed graphics card does not support the opengl features recommended...") and the program ends. The graphics card is the ATI Radeon 9000 Pro (64MB)
I'm looking for a definitive answer regarding my hardware compatibility with FCS2 (specifically, FCP6). I'm NOT looking for an answer along the lines of: your system is too old to run this.
I've checked the minimum system requirements from the apple website (http://www.apple.com/finalcutstudio/specs/
and http://www.apple.com/finalcutstudio/download/):
* A Macintosh computer with a 1.25GHz or faster PowerPC G4, PowerPC G5, Intel Core Duo, or Intel Xeon processor
* 1GB of RAM
* An AGP or PCI Express Quartz Extreme graphics card (Final Cut Studio is not compatible with integrated Intel graphics processors)
* A display with 1024-by-768 resolution or higher
* Mac OS X v10.4.11 or later
* QuickTime 7.3 or later
* DVD drive for installation
I have all that stuff. What I'd like is to know which component of my system is FCP6 complaining about (vis-a-vis the error message above), alternatively, if someone has had success with a similar configuration, I'd like to know anything they think might help.
Thanks in advance for any helpful advice you may have.

The minimum would probably be an nVidia Fx5200 or an ATI 9600...
Patrick

This app does not support the contract specified or is not installed

I was successfully creating Windows Store Apps using Visual Studio 2013, using my dev account. VS has recently re-registered my ID as well.
Today, any Strore App (including "Mail", "Store", "PC Settings"...) not running nor any of project is not launching when I start debugging. It gives dialog as shown below. Also, as the app starts showing as installed in the
start screen, when I tap it there, it doesn't run. Just splash screen flashes for a few seconds and then disappears.
Microsoft Visual Studio
Unable to activate Windows Store app '3a829624-c06f-426b-8186-9312684573a2_bs4v6h88qrjp4!App'. The activation request failed with error 'This app does not support the contract specified or is not installed'.
See help for advice on troubleshooting the issue.
OK Help
If a post solves the problem you asked, please mark it as Answer.

This question needs to be asked on answers.microsoft.com. It is not a development question.
Matt Small - Microsoft Escalation Engineer - Forum Moderator
If my reply answers your question, please mark this post as answered.
NOTE: If I ask for code, please provide something that I can drop directly into a project and run (including XAML), or an actual application project. I'm trying to help a lot of people, so I don't have time to figure out weird snippets with undefined
objects and unknown namespaces.

OATS CPU does not support the SSE2 instruction set required to run JRockit

Hello,
I am trying to get the OATS agents to work on some injector machines, however, when I try to start them I get the following error:
"[ERROR] Your CPU does not support the SSE2 instruction set required to run JRockit.
Could not create the Java Virtual Machine."
Is there a way to configure OATs to use the Sun JDK instead? I have the Sun JDK in my path and JAVA_HOME set accordingly, however that doesn't seem to make a difference. Alternatively, is there a workaround to this problem?
Thanks,
Michael.

Hi Tab,
In this case, SQL Server Analysis Services doesn’t support Distributed Transactions by design. Here is a similar thread about this issue for your reference, please see:
http://social.technet.microsoft.com/Forums/en-US/8b07be45-01b6-49d4-b773-9f441c0e44c9/olaplinked-server-error-msolap-for-linked-server-olaplinked-server-does-not-support-the?forum=sqlanalysisservices
One workaround is that use SQLCMD to execute the EXEC AT command and saved the results to a file, then import using SSIS.
If you have any feedback on our support, please click
here.
Regards,
Elvis Long
TechNet Community Support

I keep getting this error message "Your operating system does not support the 64-bit version of Silverlight" even though I have a 64 bit system?

Netflix requires Microsoft Silverlight plug in to view their videos. Every time I try to load it I get the following error message...Your operating system does not support the 64-bit version of Silverlight. I have a 64bit system with Windows Vista Home Premium. Firefox 33.0 is installed.
Any suggestions?

Your User Agent: Mozilla/5.0 (Windows NT 6.0; '''WOW64'''; rv:33.0) Gecko/20100101 Firefox/33.0
As said Firefox for Windows from mozilla.org is a 32-bit application. The WOW64 in UA means it is a 32-bit application on 64-bit Windows.
Before you ask if there will be a Win64 version of Firefox. If all goes well the first phase of having Win64 for Release may be as early as Firefox 37.0
https://wiki.mozilla.org/Firefox/win64

Error System "Item does not exist. It may have been deleted by another user"

Error System "Item does not exist. It may have been deleted by another user" in sharepoint 2010
This is problem show when User new item in List . User open new item page about 3 pages and User save each one page when page save complete , User will save another page.
Sometime User can not save item , it show that error
This List not have workflow and code
Please let me know what is the issue ?

Hi,
Greetings. THis is a known issue and see the links for resolution
http://support.microsoft.com/kb/972225
http://social.technet.microsoft.com/Forums/office/en-US/638e4aa0-527c-4b20-a899-a0cf181983ec/no-item-exists-at-it-may-have-been-deleted-or-renamed-by-another-user?forum=sharepointadminlegacy
Please remember to click 'Mark as Answer' on the answer if it helps you

Farm Remote App 2012 R : Your system administrator does not allow the use of default credentials to log on to Work Resources

Hi
Here is the situation:
I have a Farm with 3 servers W2012R2 in a Domain
Server1                           Server 2
Server3
RDSession Host            RDSession Host
RDSession Host
Connection Broker        Connection Broker (Passive)
RD Web Access
2 DNS Alias : - poc.mydomain.local (Use for the RD Web Access and points to Server1
                  -poccb.mydomain.local (Use for the Connection Broker and points to Server1)
I have setup the Connection broker in HA with Server2 as Passive Server : DNS Round Robin poccb.mydomain.local (Server1)
The certificate Manager has generated 2 CA certificates :
- 1 for the RD Web Acc (poc.mydomain.local
-1 for Connection Broker SSO and for publishing
I have created 1 Group Policy for these 3 servers and 1 GP for my client Windows 7 SP1.
Server GPO :
Computer/Administrative Templates/Windows Components/Remote Desktop Services/Remote Desktop Session Host/Security
Always prompt for password upon connection=Disabled
Require use of specific security layer for remote (RDP) connections : SSL (TLS 1.0)
Set client connection encryption level : High Level
Client GPO
Computer/Administrative Templates/System/Credentials Delegation = Allow delegating default credentials (Concatenate OS defaults with input above)
TERMSRV/POCCB.mydomain.local
I use no Gateway and in my collection,I have activated SSL (Like in my Server GPO)
I have now problem with SSO.
Connection with remote desktop client with server name = poccb.mydomain.local
Your system administrator does not allow you the use of default credentials to log on to the remote computer poccb.mydomain.local because its identity is not fully verified
If in my client GPO I add the physical name of the 3 servers, it works :
TERMSRV/Server1
TERMSRV/Server2
TERMSRV/Server3
Open RDP Files with server name = poccb.mydomain.local
if my connection broker connects me on Server1 , no problem
But If I arrive on Server2 & Server 3=
Your system administrator does not allow the use of default credentials to log on to Work Resources
I have searched on internet. No result for " to log on to Work Resources"
Any idea ? Thanks for your help

Hi,
Thank you for posting in Windows Server Forum.
Firstly check that, your user is using domain\username to enter the credential in the dialog box.
Now for a try, you can edit .rdp file with notepad and just place “enablecredsspsupport:i:0” line in it, save it an launch to check whether you are facing same issue.
As you are using windows 7 then upgrade to RDP 8.1. Also as you have already enter the FQDN name of server under “Allow delegating default credentials”. For a try please enable and configure for all the remaining settings as follow and check the result.
Start / Run / gpedit.msc / Computer Configuration / Administrative Templates / System / Credentials Delegation, and make sure you have the following four options enabled and configured:
Allow Delegating Default Credentials with NTLM-only Server Authentication
Allow Delegating Default Credentials
Allow Delegating Saved Credentials
Allow Delegating Saved Credentials with NTLM-only Server Authentication
Finally, open a command prompt and use “gpupdate /force” command to apply the policy directly.
More information:
Remote desktop credentials did not work
Hope it helps!
Thanks.
Dharmesh Solanki

Ever since enabling Soft Delete on one of my tables, the logs are flooded with "... does not support the 'deleted' system property"

I enabled Soft Delete on one of my Azure Mobile Services tables, and ever since then, the logs are flooded with tons of warnings that say something like this:
The table 'Section' does not support the 'deleted' system property.
Is there a way to suppress these warnings, or is it advisable to enable soft delete for all of my tables?
As a follow on, is there a way to export the logs so that it's easier to peruse through them and search?
Thanks :)

Hi
You can set your logging level in Azure Admin portal to be Error only, so it only logs errors and warnings will be ignored.
Regards
Aram

Native error code -2147217887 0x80040e21 Microsoft OLE DB Provider for ODBC Drivers: ODBC driver does not support the requested properties.

I configured MySQL in TestStand and making a query in TestStand like this:
Command :=> "SELECT * FROM crc_table ; " or "SELECT CRC_Value FROM crc_table ; " returns the total number of records without any errors.
But when I add the "where" clause
"SELECT crc_table.CRC_Value FROM crc_table where crc_table.File_ID= Locals.File_ID and crc_table.Version_ID = Locals.Version_ID and crc_table.Link_ID = Locals.Link_ID; "
I get the error as:
Error, The following SQL command failed: 'SELECT crc_table.CRC_Value FROM crc_table where crc_table.File_ID= Locals.File_ID and crc_table.Version_ID = Locals.Version_ID and crc_table.Link_ID = Locals.Link_ID; ...' Native error code -2147217887 0x80040e21 Microsoft OLE DB Provider for ODBC Drivers: ODBC driver does not support the requested properties. [Error Code: -10, User-defined error code.]
I tried the same syntax in MySQL Query Browser and got the correct result:
SELECT crc_table.CRC_Value FROM crc_table where crc_table.File_ID= "FID1" and crc_table.Version_ID = "VID1" and crc_table.Link_ID = "L1";
I would appreciate your help.
Thank you,
Vidula

Vidula,
I am not completely sure if this is the cause of the error but it is something that will cause problems if it is not fixed. In your SQL statement you must properly concatenate your strings with your variables. In the statement you posted you were simply putting the variable names in the string, not actually pulling their values. To do so properly your query should look something like this:
"SELECT crc_table.CRC_Value FROM crc_table where crc_table.File_ID='"+Locals.File_ID+"' and crc_table.Version_ID = '"+ Locals.Version_ID+"' and crc_table.Link_ID = '"+Locals.Link_ID+"' ;"
This way we are using the values of the variables in conjunction with the text strings. In this case the usage of single quotes (') casts the variables as strings so you may need to change this character sequence, but from the second example you gave I think that your variables are of type string so this should work fine.
Message Edited by herosphro on 04-01-2008 03:52 PM
John B.
Applications Engineer
National Instruments

Win2012R2 error 364 Content file download failed.Reason: The server does not support the necessary HTTP protocol.

Im running WSUS on Windows 2012 R2. Installed over "Add Roles and Features". Configured, synchronisation works, but can not download any updates.
System
Provider
Name]
Windows Server Update
Services
EventID
364
Qualifiers]
0
Level
2
Task
2
Keywords
0x80000000000000
TimeCreated
SystemTime]
2014-08-27T06:43:36.000000000Z
EventRecordID
390
Channel
Application
Computer
wsus-server.murrcz.local
Security
EventData
Content file download
failed. Reason: The server does not support the necessary HTTP protocol.
Background Intelligent Transfer Service (BITS) requires that the server support
the Range protocol header. Source File:
/msdownload/update/software/crup/2011/03/windows6.1-kb2506014-x64_8c22199a738b51dbfe78262ca21ba98cf8bdeca2.cab
Destination File:
C:\WSUS-updates\WsusContent\A2\8C22199A738B51DBFE78262CA21BA98CF8BDECA2.cab
The online help not works:
Content download has failed. BITS service is not starting or is stopping during downloads.
Open a command window.
Type sc config bits start= auto
Type net stop bits && net start bits
Type net stop wsusservice && net start wsusservice
Start WSUS 3.0: Click Start, click Administrative Tools, then click
Microsoft Windows Server Update Services v3.0.
Click Synchronization Results.
In the Action pane, click Synchronize Now.
Verify
Look for the corresponding error event.
Open a command window.
Type cd <WSUSInstallDir>\Tools
Type wsusutil checkhealth
Type eventvwr
Review the Application log for the most recent events from source Windows Server Update Services and event id 10030.
The KB922330 not aplicable, ExecuteSQL.exe not present.
Please help.
Thanks

.\SQLCMD.EXE -S \\.\pipe\MICROSOFT##WID\tsql\query -d "SUSDB" -Q "update tbConfigurationC set BitDownloadPriorityForegroud=1"
This should be considered a temporary fix. It will saturate your Internet connection during periods of WSUS downloads in this configuration.
The correct and permanent fix should be to resolve the failure of your perimeter device to properly support the HTTP v1.1 protocol specification (which is now some 14 years old).
Either your device is misconfigured, or it needs a firmware update to support the full specification.
Lawrence Garvin, M.S., MCSA, MCITP:EA, MCDBA
SolarWinds Head Geek
Microsoft MVP - Software Packaging, Deployment & Servicing (2005-2014)
My MVP Profile: http://mvp.microsoft.com/en-us/mvp/Lawrence%20R%20Garvin-32101
http://www.solarwinds.com/gotmicrosoft
The views expressed on this post are mine and do not necessarily reflect the views of SolarWinds.

Can anyone tell me what this Time Machine error means? The network backup disk does not support the required AFP features?

Can anyone tell me what this Time Machine error means? The network backup disk does not support the required AFP features?

AFP - Apple Filing Protocol
The Network Attached Storage (NAS) that you are pointing Time Machine at does not have the features needed by Time Machine in order to do its Thing. Time Machine needs some specific features that are not typically available on generic networked storage devices.
There are manufactures that support the Mac OS X HFS+ file system formats and implement all the needed AFP protocol packets necessary so that they can be used with Time Machine, but apparently yours does not.
If you are not using a networked mounted volume for Time Machine, then more information will be needed about your Time Machine setup.

Getting error:- Your CPU does not support long mode. Use a 32bit distribution--? on OEL 64 bit host for OEL 64 bitguest

Getting error:- Your CPU does not support long mode. Use a 32bit distribution--?
I am using entire Oracle Stack..OEL, ORACLE VBOX
Trying to install guest OEL 5.6 x86-64 bit on virtualbox 4.3 on a (Dell 2950 Server with host OS OEL 5.6 x86-64 bit) .
and it complains of -->Your CPU does not support long mode. Use a 32bit distribution
I am struck and unsure how to proceed . I appreciate any help regarding this.
I enabled the VT (Virtualization Technology) option in the BIOS and then gave it a try. Does not work?

Hi
Looks like the 64 Bit operating system is not supported. Enable the VT (Virtualization Technology) option in the BIOS and then give a try again.
Edited by: 891882 on Oct 28, 2011 1:21 PM

Error: Current provider does not support returning multiple recordsets from a single execution

Hello,
The following piece of code which has been working for the
past five years suddenly started giving me the following error:
Current provider does not support returning multiple recordsets
from a single execution
We have recenlty moved this site to a new server. Could this
error be related to their CFAdmin settings? Eveything else on the
site seems to be working fine. Or am I using an outdated tag or
something?
Any light in this direction is appreciated, thanks.
Here's the code:

There doesn't seem to be anything that seems wrong with the
code. It might have something to do with the Max Pooled Statements
or Number of Connections settings in the CF Administrator, but it
could just as easily have something to do with a setting on the
database. I would check with your provider.

HT3275 Since updating OS to Mountain Lion from leopard, I get the following error message when trying to backup with time machine on external drive. Could not complete backup to media share. The network backup disk does not support the required AFP feat

Since updating OS to Mountain Lion from leopard, I get the following error message when trying to backup with time machine on external drive. "Could not complete backup to media share. The network backup disk does not support the required AFP features." What are AFP features and how do I get Time Machine to backup to my current external backup?

This means that your NAS does not support the required encryption. Update your NAS to the latest firmware or ditch it and buy a Time Capsule (they are the most reliable when using TM).

Using time warner road runner. when I try to open up safari to home page I get error message that this version does not support the "community toolbar" can't proceed until closing the error message. sick of seeing it

using time warner road runner. when I try to open up safari to home page I get error message that this version does not support the "community toolbar" can't proceed until closing the error message. sick of seeing it

That toolbar/ct plugin seems to cause problems for all who install it!
Close Safari, then locate and delete the following files and it should be gone:
/Library/Application Support/Conduit
/Library/InputManagers/CTLoader
/Library/Receipts/ctloader.pkg
/Library/Receipts/<Toolbar name>.pkg
/Library/Application Support/SIMBL/Plugins/CT2285220.bundle
/Users/<User name>/Library/Application Support/Conduit
where / is the root library on your Hard Disk.
If you are running Snow Leopard you should also look here:
Library/launchAgents/com.conduit.loader.agent.plist
Library/Application support/conduit plugins
Also, as mentioned by Gilli2000:
Library/Receipts - If you read it, it has information in it at the bottom referring extensively to "CT" and "community toolbar".
Maybe it is harmless, but trash those items anyway!
Note: Safari does not support any third-party toolbars except those supplied as an extension to Safari via the Extension Gallery.

Cat0-3750 upgrade. Error: system number 1 does not support the same feature

Similar Messages

Maybe you are looking for