Cdp neighbour shows the same switch as neighbour and the connected switch

Hi
I have a problem here , cdp neighbor  shows the same switch as the neighbor and the real connected switchh . I know it will show only the real connected switch if i shut and no sh . What i just want know is it a symptom for something else 
Dist#sh cdp neighbors   Gig 10/10       
Capability Codes: R - Router, T - Trans Bridge, B - Source Route Bridge
                  S - Switch, H - Host, I - IGMP, r - Repeater, P - Phone,
                  D - Remote, C - CVTA, M - Two-port Mac Relay
Device ID        Local Intrfce     Holdtme    Capability  Platform  Port ID
Sw1
                 Gig 10/10        130              S I   WS-C3560- Gig 0/3
Dist
                 Gig 10/10         156             R S I  WS-C6513    Gig 10/10
Thank you

HI,
Did you did shut and no shut in the interface. ?
Is it working fine.?
is it fiber connected cable connected with these devices ?
Regards,
Gurudath K S

Similar Messages

  • I can not restore my Iphone 3gs i can turn it off an on but itunes cant connect because i have a lock on it but at the same time it shows the connect to itunes screen

    I cant restore my iphone becasue its locked an it keeps showing the Connect to itunes screeen

    Hello louii23,
    Try reconnecting it in Recovery Mode as described in this article.
    http://support.apple.com/kb/ht1808
    B-rock

  • My ipad is showing the connect to itunes and will not move from there.

    After trying to update my ipad. I recieved an "unable to update" error message. Now all my ipad will do is show the connect to itunes symbols. I cannot get is to restart or restore. itunes is not recognizing the ipad.

    You will probably need to restore using Recovery Mode. You can read about it here.
    http://support.apple.com/kb/ht4097
    Or you can follow these Recovery Mode Instructions
    Disconnect the USB cable from the iPad, but leave the other end of the cable connected to your computer's USB port.
    Turn off iPad: Press and hold the Sleep/Wake button for a few seconds until the red slider appears, then slide the slider. Wait for iPad to turn off.
    If you cannot turn off iPad using the slider, press and hold the Sleep/Wake and Home buttons at the same time. When the iPad turns off, release the Sleep/Wake and Home buttons.
    While pressing and holding the Home button, reconnect the USB cable to iPad. When you reconnect the USB cable, iPad should power on.
    Continue holding the Home button until you see the "Connect to iTunes" screen. When this screen appears you can release the Home button.
    If necessary, open iTunes. You should see the recovery mode alert that iTunes has detected an iPad in recovery mode.
    Use iTunes to restore iPad.

  • HT201210 My iPod constantly shows the 'connect to iTunes' sign, how to fix this?

    My iPod is showing the 'connect to iTunes' sign, even when I connect to iTunes and do everything it says to do. I have repeated this process several times and still no change. I believe it has wiped everything off of my iPod but I can't access anything on it as it is always on the same screen. Can it be fixed?

    Maybe:
    Restore loop (being prompted to restore again after a restore successfully completes)
    Troubleshoot your USB connection. If the issue persists, out-of-date or incorrectly configured third-party security software may be causing this issue. Please follow Troubleshooting security software issues. .
    Next try placing in DFU mode and then restoring.
    How to put iPod touch / iPhone into DFU mode « Karthik's scribblings
    Then try restoring on another computer.
    Last, make an appointment at the Genius Bar of an Apple store.
    Apple Retail Store - Genius Bar

  • Hey my iPod is not showing up on iTunes and my computer doesn't recognize it. It runs out of battery very fast and only shows the 'Connect to iTunes" screen. What do I do?

    Hey my iPod is not showing up on iTunes and my computer doesn't recognize it. It runs out of battery very fast and only shows the 'Connect to iTunes" screen. What do I do?

    http://support.apple.com/kb/ht1808
    http://support.apple.com/kb/ts1567
    Basic troubleshooting steps  
    17" 2.2GHz i7 Quad-Core MacBook Pro  8G RAM  750G HD + OCZ Vertex 3 SSD Boot HD 
    Got problems with your Apple iDevice-like iPhone, iPad or iPod touch? Try Troubleshooting 101

  • Is there a way to ensure that data has been wiped from my iphone 3g. It shows the "connect to itunes" screen when turned on.

    Is there a way to ensure that data has been wiped from my iphone 3g. It shows the "connect to itunes" screen when turned on.

    That is how it appears brand new out of the box.

  • My ipod touch is not getting recognised after the update in my itunes library. the library is updated. and it shows the connect to itunes sign.

    my ipod touch is not getting recognised after the update in my itunes library. i have updated my library as well. but it shows the connect to itunes sign on my ipod.

    If it happened after updating iTunes on the computer see:
    iOS: Device not recognized in iTunes for Windows
    or
    iPhone, iPad, iPod touch: Device not recognized in iTunes for Mac OS X
    If after updating the iOS on your iPod:
    Try:
    - iOS: Not responding or does not turn on
    - Also try DFU mode after try recovery mode
    How to put iPod touch / iPhone into DFU mode « Karthik's scribblings
    - If not successful and you can't fully turn the iOS device fully off, let the battery fully drain. After charging for an least an hour try the above again.
    - If still not successful that usually indicates a hardware problem and an appointment at the Genius Bar of an Apple store is in order.
    Apple Retail Store - Genius Bar       

  • HT201263 my ipad still will not start. When connected to wall charger it shows the connect to itunes. When connected to computer it is a black screen and slightly blinks

    my ipad still will not start. When connected to wall charger it shows the connect to itunes. When connected to computer it is a black screen and slightly blinks

    Frozen or unresponsive iPad
    Resolve these most common issues:
        •    Display remains black or blank
        •    Touch screen not responding
        •    Application unexpectedly closes or freezes
    http://www.apple.com/support/ipad/assistant/ipad/
    iPad Frozen, not responding, how to fix
    http://appletoolbox.com/2012/07/ipad-frozen-not-responding-how-to-fix/
    iPad Frozen? How to Force Quit an App, Reset or Restart Your iPad
    http://ipadacademy.com/2010/11/ipad-frozen-how-to-force-quit-an-app-reset-or-res tart-your-ipad
    Black or Blank Screen on iPad or iPhone
    http://appletoolbox.com/2012/10/black-or-blank-screen-on-ipad-or-iphone/
    What to Do When Your iPad Won't Turn On
    http://ipad.about.com/od/iPad_Troubleshooting/ss/What-To-Do-When-Your-Ipad-Wo-No t-Turn-On.htm
    iOS: Not responding or does not turn on
    http://support.apple.com/kb/TS3281
    Home button not working or unresponsive, fix
    http://appletoolbox.com/2013/04/home-button-not-working-or-unresponsive-fix/
    iPad: Basic troubleshooting
    http://support.apple.com/kb/TS3274
    Using iPhone/iPad Recovery Mode
    http://ipod.about.com/od/iphonetroubleshooting/a/Iphone-Recovery-Mode.htm
     Cheers, Tom

  • My phone has been set up previously for itunes on my lap top but my phone now shows the connect to itunes message even though the phone is connected....Ive tried every thing I can think of ...now I cant use my phone ..please help ?

    My phone has been set up previously for itunes on my lap top but my phone now shows the connect to itunes message even though the phone is connected....Ive tried every thing I can think of ...now I cant use my phone ..please help ?

    Turn your phone off and connect your cable to the computer, but not the device just yet. Start up iTunes. Now, hold down the home button on your phone and plug it in to the cable - don't let go of the button until iTunes tells you it's detected a phone in recovery mode. Now you can restore to factory settings.
    Unfortunately, the data on your phone is already gone if you're seeing the connect to iTunes logo.

  • I have an Iphone 4 and it keeps kicking in the 3G instead of using my wifi. My wifi works well with all other devices and the password is fine. I connect and it show the connection then goes back to 3G.   Thank you

    I have an Iphone 4 and it keeps kicking in the 3G instead of using my wifi. My wifi works well with all other devices and the password is fine. I connect and it show the connection then goes back to 3G.   Thank you

    This crap just happened to me this morning where I was sent 90% data plan threshold warningfrom AT&T (while sleeping at 7:09am) then 5 minutes later getting the Overage data plan warning from AT&T.  This is all while I'm asleep right next to my phone plugged into a (non-Apple) dock on my clock radio.
    Android has a limiting feature, why can't the "smart" guys at Apple learn from this??

  • I updated my iPhone today over wifi.  It downloaded 6.1.3 completely and started then installed it.  After the install all it does is show the connect to iTunes screen.  What did I do wrong and now do I have to completely restore the phone?

    I updated my iPhone today over wifi.  It downloaded 6.1.3 completely and started then installed it.  After the install all it does is show the connect to iTunes screen.  What did I do wrong and now do I have to completely restore the phone?

    Next question.... I did an iCloud save point earlier today so in theory everything should have been saved and the restore won't be a complete loss right?  Please tell me my pics aren't gone.....
    Thanks for the help.

  • Its just on the screen that shows the connect to itunes thing, someone pleaseee help ?

    Okay my ipod needs to be restored, but I have a passcode on it, and it wont let me do anything because i have a passcode.its just on the screen that shows the connect to itunes thing, someone please help? i would greatly appreciate it (:

    Connect in recovery mode and restore.
    If you cannot remember the passcode, you will need to restore your device using the computer with which you last synced it. This allows you to reset your passcode and resync the data from the device (or restore from a backup). If you restore on a different computer that was never synced with the device, you will be able to unlock the device for use and remove the passcode, but your data will not be present. Refer to Updating and restoring iPhone and iPod touch software.
    If the issue continues after updating and restoring your device, refer to this document
    iPhone and iPod touch: Wrong passcode results in red disabled screen

  • My iphone 4S only start whit cable plug in and then show battery very low (with red line end) then try to turn on but show searching in operator name command and not connecting and no work properly and when I plug out it turn off!!! what should I do?

    My iphone 4S only start whit cable plug in and then show battery very low (with red line end) then try to turn on but show searching in operator name command and not connecting and no work properly and when I plug out it turn off!!! what should I do?

    I'm afraid you'll have to get the phone serviced, dropping the phone must have damaged additional parts inside the phone.
    But Apple will not service the phone anymore, opening the phone and replacing the battery should only be done by authorized personal, not by users.
    You'll have to look for a 3rd party repair shop and see if they can fix this, sorry.

  • My touch shows the connect to itunes with usb on screen however when i try to do so it says it cannot connect because it is locked with a passcode. It will not let me enter the code on the ipod or computer. so i cant do anything. Any ideas?

    I have tried rebooting it. nothing seems to help. it always ends up with the same screen a picture prompting me to hook up via usb to itunes.Then without fail i get an error message. itunes connpt connect to the ipod touch because it is locked with a passcode. you need to enter the passcode on the ipod touch first. unfortunately the touch will not show any other screen but the connect to itunes.

    Connect the iPod touch to your iTunes library in Recovery Mode and restore it to factory setting.  See this article for instructions on getting your device into Recovery Mode.
    http://support.apple.com/kb/ht1808
    B-rock

  • Tried to restore my iPod touch, it now shows the 'connect to itunes' graphic on the screen but nothing happens when I do

    I basically restored my iPod to start my music collection from scratch because I got a new PC.
    I plugged the 32gb iPod touch into my PC and the USB connection sound went on to indicate that it is connected to the PC but the 'Connect To iTunes' graphic is on, even when it is connected to the PC and iTunes is open it doesn't show any devices connected. After a while the iPod shuts itself off, and when I turn it on again the same thing happens. Graphic. Not found in iTunes. Turns off. I think but I can't remember if I updated the iPod's operating system prior to the restore (this all happened 2 weeks ago).
    I'm not sure of the model/generation of the iPod. I got it brand new for Christmas of 2009 in Australia.
    Any help would be appreciated!

    Try here:
    iOS: Device not recognized in iTunes for Windows
    Also include manually placing the iPod in Recovery mode and then try a restore
    Then try DFU mode and restore.
    How to put iPod touch / iPhone into DFU mode « Karthik's scribblings
    Further, try another computer to help determine if yu have a compter or iPod problem.

  • TS3682 my iPad does not appear in the iTune device and it shows the "connect to iTunes" all the time.

    during the update of my iPad some error report came and after that it is not working. i have tried pressing the off key and home key at the same time. i also reinstalled the iTunes bt it is not showing any results.
    please let me know what to do?

    If you are seeing the "connect to iTunes" message - You probably need to restore your iPad using Recovery Mode. Here are the instructions.
    http://support.apple.com/kb/ht4097

Maybe you are looking for

  • How do i delete multiple playlists at one time

    I created a playlist and itunes copied it somehow like over a 1000 times and it is very difficult to delte them all i think  as i am deleting them it keeps making more how can i locate the file that is recreating them with out deleting itunes and sta

  • [Urgent]   sending a custom report to 200+ users

    Hi, I am new to BO and wanted to know if there is an option in BO to Automate report to be sent to a group of users. Say for example, if there is a report with details of Employees. Assume there are n number of managers, each manager should get a rep

  • Solo Safe Mode - How to Disable It Forever and Ever?

    The little red line over the Solo button keeps reappearing, often without my notice, so when I go to bounce some other track, say, a kick, there's a ukelele, say, playing along. Is there some easy way to disable this "feature" of Logic Pro 8?

  • Shuttle Item in 3.1

    I noticed that since the last update I have problems with the shuttle item receiving an error Bad Request Your browser sent a request that this server could not understand. mod_plsql: /pls/otn/wwv_flow.accept HTTP-400 Too many arguments passed in. Go

  • USBTMC Gaussmeter

    Hey everybody! I'm a total LabView newbie, so I've got a feeling that my question is probably answered in about a dozen places.  All help is appreciated, and please feel free to point me to other threads/tutorials/examples. My company is using LabVie