Centralized Time Machine Backup on RAID 6 enable NAS

Hello. I have over 100 Mac computers on my network. I want to have Time Machine backups on each of these machine to a Centralized RAID 6 enabled NAS. All Machines are running Snow Leopard. Can anyone please guide me how to setup this. Thank you in Advance.

Sorry, but you're going to need another solution. Time Machine doesn't back-up to NAS devices: http://support.apple.com/kb/HT1733

Similar Messages

Restore Time Machine backup to Raid 0 (Striped set)?

I've been struggling with setting up my Mac mini (late 2012) server with a Striped RAID set and then restoring a Time Machine backup to the new RAID 0 volume. Here are the steps I have undertaken:
Bought a 3TB Airport Time Capsule and created a full restore of my existing Time Machine backups to it.
My Mac mini has dual 1TB hard drives. Pressed Command + R on bootup and entered recovery mode.
Using Disk Utility, I created a Striped RAID set by adding both my 1TB drives as slices to a new RAID set and clicked on Create.
After the RAID set was created, I exited Disk Utility.
Clicked on Restore from Time Machine Backup.
The process fails as it cannot create a Recovery Partition on a RAID set.
After much exploration, I think the problem can be resolved by attempting to Reinstall OS X on Step 5 and then attempting a Time Machine restore after the core OS is in place. Thoughts?

Additional Information
A Recovery partition cannot be created on RAID volumes. If your startup device is a RAID volume, you back up and reconfigure your computer to use a non-RAID boot volume. If needed, create a separate RAID volume for data which is not the target of the OS X installation. You can also create an external, bootable drive with a Recovery partition, as described above.
See this article if the following message appears during the install process:
"Install Failed: OS X could not be installed on your computer. OS X can't be installed on the disk because a recovery system can't be created. Visit www.apple.com/support/no-recovery to learn more"
From:
http://support.apple.com/kb/HT4649

How can i access the Time Machine backup on my QSAN NAS device?

Hi
I have a QSAN TS412 TurboNas. I have set it up to be used for Time Machine backup and it works fine.
I have anothe device with over a year worth of backups on it and i would like to transfer them to the QSAN device, however the TimeMachine location is not accessible in finder, only the TM app can access it.
I am not the farmiliar with MAC's but am sure there must be a way to get the files where i want them.
Any help is much appreciated.
Ben

Byocky wrote:
Hi
I have been trying to talk to QSAN, but it is very tedious. They are not the most helpful of companies.
I have 10.7.4, it is supported by QSAn, but they just say that it cannot be accessed by finder.
I though a "wiz kid" in the forum may know what to do.
Ben
Gotcha, well good luck...maybe someone has experience with them.

Help Incomplete Time Machine Backup and I can't set ownership options

Two days ago my iMac HD stopped working and I decided it was time to upgrade my machine so I purchased a new iMac with Mavericks installed. I seem to only have a partial Time Machine Backup located on my NAS drive, so I read various threads about how to manually retrieve files from the .inprogress file. I was able to browse the package contents and when I navigated to Macintosh HD the folder was greyed out and when I attempt to open the folder it looks empty. When I select get info the Macintosh HD folder shows almost 80GB and over 160,000 files inside. I tried copying the folder onto the desktop which failed and also onto an external drive formatted the same way as the NAS - Mac OS Extended (Journaled, Case Sensitive). Everytime I try it says something along the lines of me not having the ownership rights to copy the file over.
I tried going to the NAS drive and the mounted sparsefile and couldn't figure out how to get the ignore ownership on this volume option. When I go to Disk Utility it says Owners Enabled Yes, I can't figure out how to turn that off to let me copy the file over. I tried some recommendations about creating an Alias to Macintosh HD and also setting up Automator actions Get Selected Finder Items > Get Folder Contents > Open Finder Items > Copy Finder Items (to desktop or external drive) both of these failed.
I also don't understand why I can't view the files inside the greyed out Macintosh HD as get info shows many files inside. The sharing and permissions already says everyone can read. Is there anyway I can recover some of the files? It would be so great!
Thanks for helping me.

I solved the problem and I hope this solution can help others with incomplete Time Machine Backups.
1. I made sure hidden files were shown by pasting the following line into Terminal:
defaults write com.apple.finder AppleShowAllFiles -boolean true ; killall Finder
2. On NAS drive I have a folder called Time Machine Backup and inside that folder it lists the different users with Time Machine Backups. I double clicked the user with the incomplete time machine backup to mount it.
3. Once mounted there should be a folder called backups.backupdb > machine name > dateandtime.inprogress. I right click that .inprogress file and selected show package contents. This lead to another folder randomly named with numbers and text. Inside that folder you should see a greyed out Macintosh HD folder. The date of the greyed out Macintosh HD folder might read something like January 24th, 1984. This appears to be the date that the Macintosh 128k was first introduced. I read on another thread that the creation date of the folder is incorrectly set after a crash resulting in the greyed out folder.
4. Due to the NAS having ownership issues I was not able to drag either the greyed out Macintosh HD or the folder above it to an external drive or the desktop of my new computer. Automator didn't work either. Here is what did work: I trashed the folder with the greyed out Macintosh HD inside from the NAS and dragged it from the trash onto my desktop. The move took a few hours to complete and the files were now all successfully on the new computer.
5. Once on the desktop the Macintosh HD folder was still greyed out. The solution was to select in the finder: View > Show Path Bar, then search for any file you remember inside your backup. For example I searched the word download and files inside the greyed out Macintosh HD folder showed up. Left clicking the file confirmed the path, that it was from the greyed out Macintosh HD folder. Now you can simply right click one of the folders in the Path Bar and open in new tab if you have Mavericks. I still couldn't directly open the Macintosh HD folder in a new tab, but I could open any of the subfolders inside in a new tab, including the users which lets you access all the backup files. I tested in Mountain Lion that you can also choose Open in Enclosing Folder by right clicking the file that you searched for or right clicking the folder in the bottom of the Path Bar.
6. Once I was done organizing backup files, I turned off hidden files by pasting this line into Terminal:
defaults write com.apple.finder AppleShowAllFiles -boolean false ; killall Finder
This took me days to figure out how to make use of an .inprogress file and greyed out Macintosh HD folder.
Hope this helps!!!

Limiting Time Machine backup size onto external drive

I have a 6TB RAID LaCie external drive that I would like to use with Time Machine. My mac has a 1TB HD which is not full. I do not want Time Machine to fill up my external drive with multiple backups. Is there some way to limit how much space Time Machine will use on an external drive? My understanding is that Time Machine will fill up the drive completely, then start overwriting the oldest files.
I do not think that I could partition the drive. But I am not sure how to do that, if it works with mac, and if I can do it now without reformating the drives. I am looking to see if there is a solution on the Time Machine software side.

Try Use Terminal to limit Time Machine sparcebundle size on timecapsule,
should work to limit Time Machine backup size on any NAS or external disk (or not...)
sudo defaults write /Library/Preferences/com.apple.TimeMachine MaxSize500000
to return to ilimited
sudo defaults delete /Library/Preferences/com.apple.TimeMachine MaxSize
if you want to reclame deleted files space shrink it use
hdiutil resize -size 500g -shrinkonly /Volumes/TimeMachineYOURNAME/YOURNAME.sparsebundle/
Regards

Limiting Time Machine backup Size with WD MyBookLive and 10.8

I cannot take credit for the any part of this solution; merely for merging and clarifying how the solutions discovered by 2 Apple Support Communities contributors much smarter than I (namely “Pondini” – Florida and “himynameismarek”) - worked perfectly for my situation. All cudo’s to these two!
I have about average or better PC skills, but am an absolute newbie with Apple. This week I got a new iMac. Having a number of home PC’s all sharing files and back up space on a Western Digital MyBookLive (“WD MBL”) 3TB network drive (NAS), naturally I wanted to use it to backup the new Mac rather than rushing out to buy an Apple Time Capsule.
There are hundreds of threads on limiting size of a Time Machine (“TM”) backup, many of which required entries in “Terminal” or were devised on older versions of OSX. I’m running OSX Mountain Lion 10.8, so was concerned they may not work.
The issues I wanted to resolve were:
Time Machine will use up all of the space on my WD MBL if left to it’s own devices.
The WD MBL is compatible with Mac and PC’s… which is good… but unlike a back up in Windows 7 Pro which will allow you to make backups in a mapped “share” you create yourself, Apple TM Backups will not; they end up in a hidden folder on the NAS (much like PC backups done with WD Smartware)
At first I thought maybe I could limit the size of a share created in the MBL, but not possible, at least not that I've seen and I have searched for days.
The solutions:
First make sure you have the latest firmware for the WD MBL as of today it is MyBookLive 02.11.09-053. From what I’ve read Western Digital fixed the compatibility issues with 10.8 Mountain Lion just recently.
Next you need to start TM so that it starts to create a back up. You can stop the back up once you see files being copied. Do this before you walk thru the video tutorial by my Marek below. WD MBL will create the hidden folder you need to find for TM Backups. This folder is called “TimeMachine” but it is not visible even in the “MBL_NAME-backup” folder in Finder.
Open safari and type “ afp://xxx.xxx.x.xxx ” but use your own ip address of your MBL. Mine was 192.168.1.120, yours will be different.
It will ask how you want to connect. CHOOSE AS A GUEST even if your MBL is protected… I’m not sure why it works but it does. Then a window will come up asking which share you’d like to mount. You will see all of your own shares plus one called software and now one called “TimeMachine”. Choose that one.
Now in “Finder” you will see a mounted shared item called “YOUR_MBL_NAME-“ (the same as the one that is probably already there but with a dash(-) at the end). You’ll also see a new “device” in the device list called “Time Machine Backups” (If you already have watched the video tutorial by Marek, you’d know you are looking for a file called “YOUR_MACHINE_NAME.sparsebundle”. Well if you browse the folder “Backups.backupdb” in the Time Machine Backups device you won’t find it… again I don’t know why but you won’t. It resides in the hidden folder called “TimeMachine” that is now visible in the thing you just mounted in step 4)
NOW watch this video tutorial http://youtu.be/Nq7mSizqUSI and follow it step by step.
Voila... issues resolved. Thank you Pondini and Marek!

Try Use Terminal to limit Time Machine sparcebundle size on timecapsule,
should work to limit Time Machine backup size on any NAS or external disk (or not...)
sudo defaults write /Library/Preferences/com.apple.TimeMachine MaxSize 500000
to return to ilimited
sudo defaults delete /Library/Preferences/com.apple.TimeMachine MaxSize
if you want to reclame deleted files space shrink it use
hdiutil resize -size 500g -shrinkonly /Volumes/TimeMachineYOURNAME/YOURNAME.sparsebundle/
Regards

I want a new and more powerful (non-Apple) wireless router but I still want to use my existing Time Capsule to continue with my Time Machine backups and I still need the Time Capsule's Network Attached Storage (NAS) features and capabilities

THE SHORTER STORY
My goal is to successfully use my existing Time Capsule (TC) with a new and more powerful wireless router. I need a new and more powerful wireless router in order to reach a distant Denon a/v receiver that is physically located in a master bedroom some 50 feet away from my modem. I need to provide this Denon a/v receiver with an Internet connection so that it can obtain its firmware updates and I need to connect this Denon a/v receiver to my network in order to use its AirPlay feature. I believe l still need the TC's Network Attached Storage (NAS) features because I am not sure if the new wireless router will provide me with the NAS like features / capabilities I need to share files between my two Apple laptops with OS X 10.8.2. And I know that I absolutely need my TC's seamless integration with Apple's Time Machine (TM) application in order to continue to make effortless backups of my two Apple laptops. To my knowledge nothing works with TM like Apple's TC. I also need the hard disk storage space built into the TC.
I cannot use a long wired Ethernet cable connection in this apartment and I cannot use power-line adapters. I have read that wireless range extenders and repeaters are difficult to successfully set-up and that they will reduce data speeds, especially so when incorrectly set-up. I cannot relocate my modem and/or primary base station wireless router.
In short, I want to use my TC with my new and more powerful wireless router. I need to stop using the TC to connect to the modem. However, I still need the TC for seamless TM backups. I also need to use the TC's built in hard drive for storage. And I may still need the TC's NAS capabilities to share files wirelessly between laptops because I am assuming the new wireless router will not provide NAS capabilities for OS X 10.8.2 (products like this/non-Apple products rarely seem to work with OS X 10.8.2/Macs to provide NAS features and capabilities). Finally, I want to continue to use my Apple laptop and AirPlay to wirelessly access and play my iTunes music collection stored on the TC's hard drive. I also want to continue to use my Apple laptop, AirPlay and Apple TV to wirelessly watch movies and TV shows stored on the additional external hard drive connected to the TC via USB. Can someone please advise on how to set-up my new Asus wireless router with my existing TC in such a way to accomplish all of this?
What is the best configuration or set-up to accomplish my above goals?
Thank you in advance for your assistance!!!
THE FULL STORY
I live in an apartment building where my existing Time Capsule (TC) is located in my living room and serves many purposes. Specially, my TC is at least all of the following:
(1) Wi-Fi router connected to Comcast Internet service via Motorola SB6121 cable modem - currently the TC is the Wi-Fi base station that connects to the modem and has the gateway address to the Internet. The TC now provides the DHCP service for the Wi-Fi network.
(2) Wireless router providing Internet and Wi-Fi network access to several Wi-Fi clients - two Apple laptop computers, an iPod touch, an iPad and an iPhone all connect wirelessly to the Internet via the TC.
(3) Wired Ethernet router providing Internet and Wi-Fi network access to three different devices - a Panasonic TV, LG Blu-Ray player and an Apple TV each use one of the three LAN ports on the back of the TC to gain access to the Internet.
(4) Primary base station in my attempt to extend my wireless network to a distant (located far away) Denon a/v receiver requiring a wired Ethernet connection - In addition to the TC, which is my primary base station, I am also using a second extended Wi-Fi base station (a Netgear branded product) to wirelessly extend my WiFi network to a Denon receiver located in the master bedroom and requiring a wired Ethernet connection. I cannot use a wired Ethernet connection to continuously travel from the living room to the master bedroom. The distance is too great as I cannot effectively hide the Ethernet cable in this apartment.
(5) Time Machine (TM) backup facilitator - I use my TC to wirelessly back-up two Apple laptops using Apple's Time Machine (TM) application. However, I ran out of storage space on my TC and therefore added external storage to it. Specifically, I added an external hard drive to my TC via the USB port on the back of the TC. I now use this added external hard drive connected to the TC via USB as the destination storage drive for my TM back-ups. I have partitioned the added external hard drive, and each of the several partitions all have enough storage space (e.g., each of the two partitions used by TM are sized at three times the hard drive space of each laptop, etc.). Everything works flawlessly.
(6) Network Attached Storage (NAS) - In addition to using the TC's Network Attached Storage (NAS) capabilities to wirelessly back-up two Apple laptops via TM, I also store other additional files on both (A) the hard drive built into the TC and (B) the additional external hard drive connected to the TC via USB (there are additional separate partitions on this drive for these other additional and non-TM backup files).
I use the TC's NAS feature with my Apple laptop and AirPlay to wirelessly access and play my iTunes music collection stored on the TC's hard drive. I also use my Apple laptop, AirPlay and Apple TV to wirelessly watch movies and TV shows stored on the additional external hard drive connected to the TC via USB. Again, everything works wirelessly and flawlessly. (Note: the Apple TV is connected to the network via Ethernet and a LAN port on the back of the TC).
The issue I am having is when I try to listen to music via Apple's AirPlay in the master bedroom. This master bedroom is located at a distance of two rooms away from the TC's current location in the living room, which is a distance of about 50 feet. This apartment has a long rectangular floor plan where each room is connected to the next in a straight line. In order to use AirPlay in the master bedroom I am using a second extended Wi-Fi base station (a Netgear branded product) to wirelessly extend my WiFi network to a Denon receiver located in the master bedroom and requiring a wired Ethernet connection. This additional base station connects wirelessly to the WiFi network provided by my TC and then gives my Denon receiver the wired Ethernet connection it needs to use AirPlay. I have tried moving my iTunes music directly onto my laptop's hard drive, and then I used AirPlay on this same laptop to connect to the Denon receiver. I always get a successful connection and the song plays, but the problem is that the connection inevitably drops.
I live in an apartment building and all of the many wireless routers in this building create a great deal of WiFi interference on both the 2.4 GHz and 5GHz bands. I have tried connecting the Netgear product to each the 2.4 and 5 GHz bands, but neither band can successfully maintain a wireless connection between the TC and the Netgear product. I also attempted to maintain a wireless connection to an iPod touch using the 2.4 GHz band and AirPlay on this iPod touch to play music on the Denon receiver. Again, I was able to establish a connection and successfully play music, but after a few minutes the connection dropped and the music stopped playing. I therefore have concluded that I have a poor wireless connection in the master bedroom. I can establish a connection, but it is intermittent with frequent drops. I have verified this with both laptops by working in the master bedroom for an entire day on both laptops. The Internet connection in this master bedroom proved to drop out frequently - about once an hour with the laptops. The wireless connection and the frequency of its dropout are far worse with the iPod touch and an iPhone.
I cannot relocate the TC. Also, this is an apartment and I therefore cannot extend the range of my network with Ethernet cable (I cannot drill through walls/ceilings, etc.). It is an old building with antiquated wiring and power-line adapters are not likely to function properly, nor can I spare the direct power outlet required with a power-line adapter. I simply need every outlet I can get and cannot afford to block any direct outlet.
My solution is to use a more powerful wireless router. I found the ASUS RT-AC66U Dual-Band Wireless-AC1750 Gigabit Router which will likely provide a better connection to my wireless Internet in the master bedroom than the TC. The 802.11ac band of this Asus wireless router is totally useless to me, but based on what I have read I believe this router will provide a stronger connection at greater distances then my TC. And I will be ready for 802.11ac when it becomes more widely available.
However, I still need to maintain the TC's ability to work seamlessly with TM to backup my two laptops. Also, I doubt the new Asus router will provide OS X 10.8.2 with NAS like features and capabilities. Therefore, I still would like to use the TC's NAS capabilities to share files on my network wirelessly assuming the Asus wireless router fails to provide this feature. I need a new and more powerful wireless router, but I need to maintain the TC's NAS features and seamless integration with TM. Finally, I want to continue to use my Apple laptop and AirPlay to wirelessly access and play my iTunes music collection stored on the TC's hard drive. I also want to continue to use my Apple laptop, AirPlay and Apple TV to wirelessly watch movies and TV shows stored on the additional external hard drive connected to the TC via USB. Can someone advise on how to set-up my existing TC with this new Asus wireless router in such a way to accomplish all of this?
Modem
Motorola SB6121 SURFboard DOCSIS 3.0 Cable Modem
Existing Wireless Router and Primary Wi-Fi Base Station - Apple Time Capsule
Apple Time Capsule MC343LL/A 1TB Sim DualBand (purchased June 2010, likely the Winter 2009 Model)
Desired New Wireless Router and Primary Wi-Fi Base Station - Non-Apple Asus
ASUS RT-AC66U Dual-Band Wireless-AC1750 Gigabit Router
Extended Wi-Fi Base Station - Provides an Ethernet Connection to a Denon A/V Receiver Two Rooms Away from the Modem
Netgear Universal Dual Band Wireless Internet Adapter for TV & Blu-Ray (WNCE3001)
Addition External Hard Drive Attached to the Existing Apple Time Capsule via USB
WD My Book Studio 4TB Mac External Hard Drive Storage USB 3.0
Existing Laptops on the Wireless Network Requiring Time Machine Backups
MacBook Air (11-inch, Mid 2012) OS X 10.8.2
MacBook Pro (13-inch Mid 2010) OS X 10.8.2
Other Existing Apple Products (Clients) on the Wireless Network
iPod Touch (second generation) is model A1288.
iPad (1st generation)
Apple TV (3rd generation) - Quantity two (2)

Thanks Bob Timmons.
In regards to a Plan B, I hear ya brother. I am already on what feels like Plan Z. Getting WiFi to a far off room in an apartment building crowded with WiFi routers is a major pain.
I am basing my thoughts on the potential of a new and more powerful router reaching the far off master bedroom based on positive reviews on cnet.com, pcmag.com and pcworld.com. All 3 of these web sites have reviewed the Asus RT-AC66U 802.11AC wireless router as well as its virtual twin cousin 802.11n router. What impressed me is that all 3 sites rated this router #1 overall in terms of both range and speed (in both the 802.11n and 802.11AC flavors). They tested the router in real world scenarios where the router needed to compete with a lot of other wireless routers. One of the sites even buried this Asus router in a media room with thick walls and inside a media cabinet. This Asus router should be able to serve my 2.4 GHz band wireless clients (iPod Touch and iPhone 4) with a 2.4GHz Wireless-N band offering some 50 feet of dependable range and a 60 Mbps throughput at that range. I am hoping that works, but it's borderline for my master bedroom. My 5 GHz wireless clients (laptops) will enjoy a 5GHz Wireless-N band offering 150 feet of range and a 200 Mbps throughput at that range. I have no idea what most of that stuff means, but I did also read that Asus could reach 300 feet and I got really excited. My mileage may vary of course and I'm sure I'm making some mistakes in my interpretation of their data. However, my Winter 2009 Time Capsule was rated by cnet.com to deliver real world performance of less than that, and 802.11AC may or may not be useful to me someday. But when this Asus arrives and provides anything other than an excellent and consistent wireless signal without drops in the master bedroom it's going right back!
Your solution sounds great, but I have some questions. I'm using OS X 10.8.2 and Airport Utility (version 6.1 610.31) and on its third tab labeled "Wireless" the top option enables you to set "Network Mode" to either:
Create a wireless network
Extend a wireless network
Off
Given your advice to "Turn off the wireless on the TC," should I set Network Mode to Off? Sorry, I'm clueless in regards to how to turn off the wireless on the TC any other way. Can you provide specific steps on how to turn off the wireless on the TC? If what I wrote is correct then what should the rest of this Wireless tab look like, or perhaps it is irrelevant when wireless is off?
Next, what do you mean by "Configure the TC in Bridge Mode?" Under Airports Utility's fourth tab labeled "Network" the top option "Router Mode" allows for either:
DHCP and Nat
DHCP Only
Off (Bridge Mode)
Is your advice to Configure the TC in Bridge Mode as simple as setting Router Mode to Off (Bridge Mode)? If yes, then what should the rest of this "Network" tab look like? Anything else involved in configuring the TC in Bridge Mode or is it really as simple as setting the Router Mode to "Off (Bridge Mode)"?
How about the other tabs in Airport Utility, can they all stay as is assuming I use the same network name and password for the new Asus wireless router? Or do I need to make any other changes to the TC via Airport Utility?
Finally, in regards to your Plan B suggestion. I agree. But do you have a Plan B for me? I would greatly appreciate any alternative you could provide. Specifically, if you needed a TC's Internet connection to reach a far off corner of your home how would you do it? In the master bedroom I need both a wired Ethernet connection for the Denon a/v receiver and wireless Internet connection for the iPhone and iPod Touch.
Power-Line Adapters - High Cost, Blocks at Least One Wall Outlet and Does Not Solve the Wireless Need
I actually like exactly one power-line adapter, which is the D-Link DHP-540 PowerLine AV 500 4-Port Gigabit Switch. This D-Link power-line adapter plugs into your wall outlet with a normal sized plug (regular standard power cord much like any other electronic device) instead of all of the other recommended power-line adapters that not only use at least one wall outlet but also often block the second outlet. You cannot use a power strip with a power-line adapter which is very impractical for me. And everything about my home is strange and upside down. The wiring here is a disaster and I don't have faith in its ability to carry Internet access from the living room to the master bedroom. And this D-Link power-line adapter costs $90 each and I need at least two to make the connection to the Denon A/V receiver. So, $180 on this solution and I still don't have a dependable drop free wireless connection in the master bedroom. The Denon might get its Ethernet Internet connection from the power-line adapter, but if I want to use an iPhone 4 or iPod Touch to stream AirPlay music to the Denon wirelessly (Pandora/iTunes, etc.) from the master bedroom the wireless connection will not be stable in there and I've already spent $190 on just the two power-line adapters needed.
Extenders / Repeaters / Wirelessly Extending the Wireless Network
I have also read great things about the Amped Wireless High Power Wireless-N 600mW Gigabit Dual Band Range Extender (Repeater) SR20000G and the My Net Wi-Fi Range Extender. The former is very powerful and the latter is easier to install. Both cost about $150 ish so similar to a new Asus router. However, everything I read about Range Extenders points to them not being very effective for a far off corner of your house wherein it's apparently hard to place the range extender in the sweet spot where it both gets a strong enough signal to actually effectively extend the wireless signal and otherwise does not reduce network throughput speeds to unacceptable speeds.
Creating a Roaming Network By Hard Wiring with Ethernet Cable - Wife Would Say, "**** No!"
Even Apple seems to warn against wirelessly extending your network (see: http://support.apple.com/kb/HT4145#) and otherwise strongly recommends a roaming network where Ethernet cable is used to connect two wireless base stations. However, I am in an apartment where stringing together two wireless base stations with Ethernet cable would have an extremely low wife acceptance factor (WAF). I cannot (both contractually and from a skill prospective) hide Ethernet wire in the walls or ceiling. And having visible Ethernet cable running from room-to-room would be unacceptable, especially to the wife.
So what is left? Do you have a Plan B for me? Thanks in advance for your help!

Time Capsule as central storage in addition to Time Machine backups?

I have been using a MacBook and just recently bought my wife the new aluminum MacBook to replace our old PC Desktop. I am considering buying the 1TB Time Capsule as well. I understand it can backup both machines via Time Machine.
My question:
I have iTunes & iPhoto databases on my MacBook which I modify, edit, and use routinely. Can I set Capsule up so that I can continue to house those databases on my laptop, but any changes sync with centrally stored databases on Capsule that my wife can access through iPhoto and iTunes on her new MacBook. She wouldn't be doing any editing or updating to either, other than use for viewing or syncing her iPod, etc.
Is this within Capsule's capabilities or is is it like my current Time Machine External HD that can only be used for Time Machine backups?
Thank you, any help would be much appreciated before I decide whether or not to make this purchase.

I don't want to discourage you from getting a Time Capsule (TC), but from my experience its primary purpose is to be the target of Time Machine backups. It can also perform as a NAS device, but it does not seem to be well suited as a media server. Sharing a single iTunes or iPhoto Library is, in my opinion, not something I would recommend, especially when streaming iTunes during Time Machine (default: once per hour) backups are running. Also you won't be able to stream the iTunes content from the TC to a media extender, like the AppleTV.
However, there's a lot of opinions out there on this topic. Here are just a few articles to get you started:
o Apple Discussions Topic : Time capsule as a media server
o Engadget: Time Capsule: everything you wanted to know
o theAppleBlog: Using Time Capsule as a Media Drive

Time Machine Backup on a NAS

Hello,
I've recently started using Time Machine to backup my iMac to my external NAS (WD MyBookLive).
The backup was done correctly, however I want to know why can't I find the backup folders & files when I browse the NAS. Instead, the Time Machine backup appears as a separate "mount" among my Devices.
I know the backup is on the NAS, judging by the free space there, but I want to know why I can't locate and browse the folder & files of the backup there (even though I've enabled the hidden folders).
Regards,

http://pondini.org/TM/2.html

How to move existent Time Machine backups to a NAS?

Hello everybody
I am not sure if I am posting this discussion in the correct community, so please move it to the right one in case you need.
Currently I am using a 1TB external hard drive to store all my time machine backups. This drive also contains other information (movies, photos etc). I bought a Western Digital MyBook World Edition II which is a NAS. I want it to move my Time Machine backups to my NAS. How can I do it? Just copy over the backups folder from the external hard drive to the NAS?
Thank you!
Gilson

That's just crazy slow.
It won't be fast, as the data can't go directly from the old disk to the new one. It must pass through your Mac, so is on the network twice, slowing the effective speed by roughly half. But that's awful.
There could be any number of causes, from bad ports or cables to problems with either drive or controller. I don't have any experience with modern RAID systems, but some of the older ones were extremely slow when there was a problem with one of the drives.
And it may get worse -- if the backups are damaged, the copy will fail and the result won't be useable.
About all I can recommend is the usual: it's always prudent to keep secondary backups. If you don't have any, I'd strongly recommend getting a (plain) external HD and making a "bootable clone" on it ASAP (that will probably slow the copy down somewhat). See Time Machine - Frequently Asked Question #27 for details and some suggestions.
It wouldn't have to be a 2 TB drive, just the same size as your internal HD (or at least 10% larger than the data on it). You might consider getting a portable drive, so you can take it to a secure off-site location once you get your TM backups working to the new WD box. Then update it periodically.

Can Synology NAS serve both time machine backup and video/audio servers?

I'm looking for a NAS box such as Synology 2 bay solution. I've seen the box can be used as Samba server to store network folders and files; and also there is discussions on Mac Time Machine backup using the Synology boxes; I'm wonder if the RAID disks can be partitioned to do both, some space for the backup from time machine and others with regular NAS services as network disk space, and if you can share your experience if you have done that.

Your answer is found on the Synology website with this link:
http://www.synology.com/en-global/support/tutorials/481

Time capsule as time machine backup and NAS?

I've read the TC section of the website and notice a blurb about computers able to connect to it as a HDD.
I realize the device has yet to be released but was wondering about this. I have a handfull of macs and a handfull of xp machines on my network (wired and wireless)
1 of my XP machine is just used as a file server. (1.5TB NTFS formated holding all video/audio/docs as well as having iTunes running to download HD podcast) All computers (Mac/XP) can access this. Five of my XP computers are MCE2005 which are configured to record SD and HD shows directly to this box.
I have yet to have a HFS formated drive to actually do time machine backups and I would like to start. I understand that going with TC I will loose some abilities I currently have by running a dedicated computer/file server but I like the fact that it is small and self contained.
I just want to make sure I understand the specifiations correctly. Can I make a various folders on TC and then map it to my Mac/XP machines via windows naming convention (ie \\TimeMachine\RecordedTV\)
I am in the process of upgrading my file server so this would be a perfect time to think about going this route. Should TC not meet my needs I will continue with my build of a Raid 5 server.

Until we get more information, at the present time the only certain thing we know about Time Capsule is that it will support TimeMachine backups.
What we don't know:
1. whether TimeMachine backups to network drives other than Time Capsule will ever be supported
2. whether the Time Capsule internal drive can be used for general file storage, or only Time Machine backups. Current information on Apple's web site could be interpreted either way. I suspect it can be used for general file storage - but that is just my opinion.
If it is not essential that you make a purchasing decision before Time Capsule ships within the next month (and more detailed information becomes available) I suggest you wait. My two cents worth of opinion - if it is general file storage that you want, and Time Machine automated backups are not a priority on the "wish list", then I think you would be far better off setting up your own network file server rather than using Time Capsule for this purpose.

Nas on airport extreme not recognized by time machine. same nas was previously used as time machine backup on different airport extreme. are there any configuration files that i can delete to fix this problem ?

nas on airport extreme not recognized by time machine. same nas was previously used as time machine backup on different airport extreme. are there any configuration files that i can delete to fix this problem ?

Time Machine has been working just fine, but in the last week or two it has given up the ghost. I reset the connections to the drive, and it will basically save a few bytes of data and then hang.
Although Apple originally announced, prior to the release of the first 802.11n AirPort Extreme Base Stations (AEBSn), that it would support Time Machine backups to AirPort Disks, they removed that option before they did finally release the base station for sale.
Since then, Apple has posted (as you have noted) that they DO NOT support Time Machine backups to AirPort Disks. As far as I know, they have not changed from that position and those who do these backups find that they become corrupted over time. Sorry, but it sounds like you just confirmed that for yourself.
1) Has one of the recent updates either on the AE (firmware) or OSX disabled this function?
No. Again, this feature has never been supported by Apple for every generation of AEBSn released.
2) Are there any changes I can make to get this working again?
If your data backups are critical to you, then you will want to use a different solution for your Time Machine backup destination drive strategy. I would suggest that you connect your WD My Book directly to your Mac in the mean time.
Your other options would be to either use a Time Capsule (which interestingly does support TM backups to AirPort Disks) or a non-Apple solution like the Drobo FS or HP MediaSmart server.

Time machine backup on NAS using WebDav?

Hi, I regularly use Time Machine to backup my mac on a NAS using my home network (Synology instructions are for configuration using the afp protocol). I have been travelling a lot lately and Time Machine backups on my NAS are not a choice. I’m using an external drive as a temporary strategy until back home. Anybody knows if it is possible to configure Time machine to backup on a NAS using WebDav protocol? If so, how to do it?
I appreciate any information / help with this.

Extremely unlikely.
It is possible to use Back to my Mac to back up to a Time Capsule over the Internet, but many folks can't get it to work; even when it does, it's very slow.
I've never seen any posts about it being done to any other Internet destination.

AEBS Ethernet NAS Hard Drive + USB Time Machine Backup

Hello,
I currently have an Airport Extreme Base Station, which I utilize the USB port for Wireless Time Machine Backups. However, I would like to know if it is possible to connect a NAS drive to the AEBS via Ethernet and still use the USB port for wireless backups for multiple Mac laptops simultaneously. The backups must also include whatever is on the NAS drive. Is this functionality possible?
Thanks!!

infamousirshad, Welcome to the discussion area!
...I would like to know if it is possible to connect a NAS drive to the AEBS via Ethernet and still use the USB port for wireless backups for multiple Mac laptops simultaneously.
Yes
The backups must also include whatever is on the NAS drive. Is this functionality possible?
No. Time Machine does not backup data FROM any network drive.

Centralized Time Machine Backup on RAID 6 enable NAS

Similar Messages

Maybe you are looking for