Changing CAS e&m-wink-start to a PRI on voice gateway

Cisco IOS Software, C3900 Software (C3900-UNIVERSALK9-M), Version 15.1(4)M4, RELEASE SOFTWARE (fc1)
I want to change a CAS e&m-wink-start to a PRI on controller T1 0/1/0 using mgcp below. I am posting the new configuration below the current e&m-wink-start configuration on the voice gateway router.
Current
controller T1 0/1/0
cablelength long 0db
ds0-group 1 timeslots 1-24 type e&m-wink-start
description
New configuration
Router(config)# no contoller T1 0/1/0
Router(config)# no interface Serial0/1/0
Router(config)#controller t1 0/1/0
Router(config-controller)#cablelength long 0db
Router(config-controller)#framing esf
Router(config-controller)#linecode b8zs
Router(config-controller)#clock source line
Router(config-controller)#pri-group timeslots 1-24 service mgcp
Router(config-controller)#description circuit ID
Router(config-if)# interface serial0/1/0
Router(config-if)# no ip address
Router(config-if)# encapsulation hdlc
Router(config-if)# isdn switch-type primary-4ess
Router(config-if)# isdn incoming-voice voice
Router(config-if)# isdn bind-l3 ccm-manager

Hi,
You need additional configs for this to work..You also need to configure the isdn bind on the D-channel not as you have it..
Router(config-if)# interface serial0/1/0:23
Router(config-if)# no ip address
Router(config-if)# encapsulation hdlc
Router(config-if)# isdn switch-type primary-4ess
Router(config-if)# isdn incoming-voice voice
Router(config-if)# isdn bind-l3 ccm-manager
Additional configs....change ip to suit your needs
ccm-manager redundant-host 192.168.103.114
ccm-manager mgcp
ccm-manager music-on-hold bind xxx--put relevant interface
mgcp
mgcp call-agent 192.168.103.115 2427 service-type mgcp version 0.1
mgcp dtmf-relay voip codec all mode out-of-band
mgcp rtp unreachable timeout 1000 action notify
mgcp modem passthrough voip mode nse
mgcp modem passthrough voip codec g711alaw
mgcp modem passthrough voip redundancy
mgcp ip qos dscp af31 media
mgcp ip qos dscp cs3 signaling
mgcp package-capability rtp-package
mgcp package-capability sst-package
mgcp package-capability pre-package
mgcp default-package dtmf-package
no mgcp package-capability res-package
no mgcp package-capability fxr-package
mgcp tse payload 100
no mgcp timer receive-rtcp
mgcp sdp simple
mgcp fax t38 inhibit
mgcp rtp payload-type g726r16 static
mgcp bind control source-interfacexx -----------------------put relevant interfcae here
mgcp bind media source-interface xxx--------------------same
Please rate all useful posts
"opportunity is a haughty goddess who waste no time with those who are unprepared"

Similar Messages

"completion insight" and "change case as you type" won't work for sql file

Hi there,
Just updated to 3.1 on my Mac Lion. It's very likely a bug since it used the work with 3.0.
I have a "temp.sql" file where I store several queries. I start SQL Developer, open "temp.sql", connect to a DB but "completion insight" and "change case as you type" won't work anymore.
If I click in "Unshared SQL Worksheet", the new worksheet tab will work fine with completion and change case, but I want to use my temp.sql and save things there when closing the application.
To reproduce yourself the issue:
Open SQL Dev, connect to a DB (it will open a worksheet), do some queries and check that change case and completion are working, quit SQL Dev, but save the worksheet in a sql file before. Re-open SQL Dev and open the sql file. Connect to the same DB and try to change the queries or create another. Completion and change case won't work anymore.
About
Oracle SQL Developer 3.1.07
Version 3.1.07
Build MAIN-07.42
Copyright © 2005, 2011 Oracle. All Rights Reserved.
IDE Version: 11.1.1.4.37.59.48
Product ID: oracle.sqldeveloper
Product Version: 11.2.0.07.42
Version
Component     Version
=========     =======
Java(TM) Platform     1.6.0_31
Oracle IDE     3.1.07.42
Versioning Support     3.1.07.42

Well, it's partially working, if your sql file is big (like mine), say with more than 1000 lines, then, maybe because of memory usage, the automatic completion won't work as expected, though, sometimes, after a while, crtl-space would stil work.
So, the problem may have been addressed, but I believe this feature can be definitely improved.

Changing case in a style ?

In IDCS2, is there a way of using a style to change case of a piece of text, or would this have to be done by scripting?
Anyone know, please ?
Bran

You're right, mate, and I realise in hindsight I was inspecific in the wording of my first post.
What I was hoping to be able to do was toggle the case between lower, upper and title case, as needed.
I'm out of my depth with scripting -- I wouldn't have a clue where to start. But in any event, am I wrong in thinking that, except in cases where the required change was regular and predictable, a script would have to be invoked manually anyway ? For my purposes, for ad-hoc sub-editing and formatting, I'm guessing it would be just as easy to use the menu.
But thanks, jongware. I appreciate your comments.

How can change Case Sensitivity in MS SQL 2008

hi expert,
I want to change Case Sensitivity to Case Insensitivity in MS SQL 2008.
how can I do??
any help please
thanks and regards
jun

Hello,
there is no way to change this. The SQL Server itself and the SAP Database are installed in an case sensitive collation. If you were albe to change this, your installation will be no longer supported and will, in the worst case, generate incorrect data within the SAP database.
So, start live with it, there is no way to change it.
Best regards
Clas

I was at level 111 on My Tom app, but when i've changed my i Phone it starts from 1st level. How can i get back my level?

I was at level 111 on My Tom app, but when i've changed my i Phone it starts from 1st level. How can i get back my level?

"When you changed your iPhone". Do you mean you purchased a new phone? If that is the case, did you restore the new phone from a backup of the old phone? Is it possible that the app you are using does not save data in the iPhone backup? Have you contacted the app developer to ask them about it?

Answer Supervision dual wink start

I have a interesting problem. I have a circuit coming in CAS set up for E&M fgb.
to a Cisco 58xx
The problem is with the wink start. The origionating switch sees immediate answer supervision when a call is made. I beleve this is becuase the Cisco sets ABCD 1111 high for 200 ms to acknowledge that the cisco can take the call., then drops ABCD to 0000. THen the termination swith sets ABCD to 1111 when the call is answered and 0000 when the call is dropped. The problem is the origionation switch responds to the first 1111 as if it were answer supervision thus providing "false" answer supervision. THe problem then is that the CDR from the origionation switch show duration even on non-completed calls and adds duration to completed calls.
Is there anyway to no send wink back to the orgionation switch from the cisco gateway and only the wink from the termination switch ? This only happens on CAS trunks.
a normal call will give me 3 offhook events and 1 on hook event
1. Off hook with the origionation swith starts the digits
2. Off Hook event with the digits are complete (this is the one providing the false answer supervision)
3. Off Hook with the termination switch completes the call (this the one that should provide the answer supervision)
4. On hook when the call is complete (this is normal)
Any help

Even though these are cas trunks, you need to have direct-inward-dial under the pots dial peer that is matched when the call comes in. This is configured by default under the dial peers for 26/36xx series routers but need to be configured for 5xxx platforms. If it is not configured then answer supervision is sent back to the switch immediately as the call comes in, but with direct-inward-dial, the answer supervision is sent to the switch, when we get a connect message back from the terminating device.

Updating Dave Saunders find style/change case script

How can I update a Dave Saunders script from CS1 and CS2 to CS5?
he wrote a brilliant script which searches for a paragraph style and changes the case to upper or lower.
However, it was for CS1 and CS2.   I can 't get it to run on CS5.
it trips up on
app.findPreferences = null;
object does not support 'findPreferences'
here is the script. thanks for your help!
//DESCRIPTION: Converts text in designated parastyle to designated case
if ((app.documents.length != 0) && (app.selection.length != 0)) {
myDoc = app.activeDocument;
myStyles = myDoc.paragraphStyles;
myStringList = myStyles.everyItem().name;
myCaseList = ["Uppercase","Lowercase", "Title case", "Sentence case"];
myCases = [ChangecaseMode.uppercase, ChangecaseMode.lowercase, ChangecaseMode.titlecase, ChangecaseMode.sentencecase];
var myDialog = app.dialogs.add({name:"Case Changer"})
with(myDialog){
with(dialogColumns.add()){
   with (dialogRows.add()) {
    with (dialogColumns.add()) {
     staticTexts.add({staticLabel:"Paragraph Style:"});
    with (dialogColumns.add()) {
     myStyle = dropdowns.add({stringList:myStringList,selectedIndex:0,minWidth:133});
   with (dialogRows.add()) {
    with (dialogColumns.add()) {
     staticTexts.add({staticLabel:"Change Case to:"});
    with (dialogColumns.add()) {
     myCase = dropdowns.add({stringList:myCaseList,selectedIndex:0,minWidth:133});
var myResult = myDialog.show();
if (myResult != true){
// user clicked Cancel
myDialog.destroy();
errorExit();
theStyle = myStyle.selectedIndex;
theCase = myCase.selectedIndex;
myDialog.destroy();
app.findPreferences = null;
app.changePreferences = null;
myFinds = myDoc.search('',false,false,undefined,{appliedParagraphStyle:myStyles[theStyle]});
myLim = myFinds.length;
for (var j=0; myLim > j; j++) {
   myFinds[j].texts[0].changecase(myCases[theCase]);
} else {
errorExit();
// +++++++ Functions Start Here +++++++++++++++++++++++
function errorExit(message) {
if (arguments.length > 0) {
if (app.version != 3) { beep() } // CS2 includes beep() function.
alert(message);
exit(); // CS exits with a beep; CS2 exits silently.

I've adapted seddybell's new script so that it works with paragraph styles instead of character styles. Hope that's useful to someone.
//DESCRIPTION: Update of Dave Saunder's ChangeCaseOfSelectedStyle script for CS5 and later
//jblondie: Fork of seddybell's update so that you can select by Paragraph Style instead of Character Style.
if ((app.documents.length != 0) && (app.selection.length != 0)) {
myDoc = app.activeDocument;
myStyles = myDoc.paragraphStyles; //jblondie: replaced character with paragraph
myStringList = myStyles.everyItem().name;
myCaseList = ["UPPERCASE","lowercase", "Title Case", "Sentence case"]; //jblondie: Changed myCaseList so it's consistent with InDesign's built in Change Case tool
myCases = [ChangecaseMode.uppercase, ChangecaseMode.lowercase, ChangecaseMode.titlecase, ChangecaseMode.sentencecase];
var myDialog = app.dialogs.add({name:"Case Changer"})
with(myDialog){
with(dialogColumns.add()){
   with (dialogRows.add()) {
    with (dialogColumns.add()) {
     staticTexts.add({staticLabel:"Paragraph Style:"}); //jblondie: replaced Character with Paragraph
    with (dialogColumns.add()) {
     myStyle = dropdowns.add({stringList:myStringList,selectedIndex:0,minWidth:133}) ;
   with (dialogRows.add()) {
    with (dialogColumns.add()) {
     staticTexts.add({staticLabel:"Change Case to:"});
    with (dialogColumns.add()) {
     myCase = dropdowns.add({stringList:myCaseList,selectedIndex:0,minWidth:133});
var myResult = myDialog.show();
if (myResult != true){
// user clicked Cancel
myDialog.destroy();
errorExit();
theStyle = myStyle.selectedIndex;
theCase = myCase.selectedIndex;
myDialog.destroy();
app.findTextPreferences = NothingEnum.NOTHING;
app.changeTextPreferences = NothingEnum.NOTHING;
app.findTextPreferences.appliedParagraphStyle = myStyles [theStyle]; var myFinds = myDoc.findText(); //jblondie: replaced Character with Paragraph
myLim = myFinds.length;
for (var j=0; myLim > j; j++) {
   myFinds[j].texts[0].changecase(myCases[theCase]);
} else {
errorExit();
// +++++++ Functions Start Here +++++++++++++++++++++++
function errorExit(message) {
if (arguments.length > 0) {
if (app.version != 3) { beep() }
alert(message);
exit();

Change Case in Column header when designing reports in BIDS

Hi
I have used a key short-cut to change the case of headers when adding them to the header of a Tablix, but I can't remember the key combination,
Any help much appretiated
Regards
Andy
CRM 4, SQL Server and .Net developer using C#

Hi Andy,
If I understand correctly, you want to know the shortcut key combination to switch the case of words in column headers of a tablix in Reporting Services Report Designer. As far as I know, there is no such key combination. In Microsoft Word/Outlook/PowerPoint,
we can use the Shift + F3 to change case of words. However, this doesn’t work in SSRS Report Designer.
To change the case of the words in column headers, you can either copy the text to Word and perform the case change there or use built-in functions such as LCase, Ucase, or StrConv to perform the case change by using expression. Here are the examples for
the three functions:
Expression: =LCase(“Sales territory country”)                           Result: sales territory country
Expression: =UCase(“Sales territory country”)                           Result: SALES TERRITORY COUNTRY
Expression: =StrConv(“Sales territory country”, vbProperCase)   Result: Sales Territory Country
Regards,
Mike Yin
If you have any feedback on our support, please click
here
Mike Yin
TechNet Community Support

Change case in paragraph style option

I use different types of headng styles in my document. I use ALL CAPS for my first level heading and TITLE CASE for second level heading and SENTENCE FOR third level heading. It will be helpful if I have change case options in paragraph sytle
Upper case
Lowera case
Title case
Sentence case
in paragaph style just like "BASIC CHARACTER FORMATS".
Thanks
Regards
arul

I think that's the wrong paradigm.
Styles are for changing the look of text -- not the content. the way change case works (in every app I've ever seen) is by changing the encoding of the text.
FWIW. I have a utility in my "Style Utilities" which can change case based on style: http://in-tools.com/products/plugins/style-utilities/
Harbs

My hard drive desktop suddenly will no longer hold or maintain the icons in place when I shut down and restart. The icons all change positions, alphabetically. Just started happening. Any thoughts?

My hard drive desktop suddenly will no longer hold or maintain the icons in place when I shut down and restart. The icons all change positions, alphabetically. Just started happening. I prefer the icons to a list format. Concerned this might be a symptom of a larger problem. Any thoughts?
revmandan

It's normal for the icons at the top level of the startup disk to revert to the same arrangement every time the Finder is relaunched. If it's important to you to arrange those icons in a persistent way, proceed as follows.
Back up all data.
Open the Info window on the startup disk (labeled "Macintosh HD" unless you gave it another name.) Click the lock icon in the lower right corner of the dialog and authenticate.
In the Sharing & Permissions section, click the plus-sign button to add an entry to the access list. Give yourself "Read and Write" access. This will be a temporary change. Leave the dialog open.
Open the Finder window and arrange the icons as you wish, then close the window.
In the Info dialog, use the minus-sign button to delete the entry you just added to the access list. Don't change anything else. When you're done, it should be the same as when you started. Close the Info dialog.

How do you change what programs open on starting up?

How do you change what programs open on start up?

By changing the list of login items for your user account in System Preferences, and if Lion is automatically reopening applications, which ones are running when the computer is shut down.
(64981)

Question for scripting gurus: GREP search, change case make Smallcaps

I have no knowledge of scripting at all, but this question keeps coming up during training sessions: is it possible to (java)script this:
- Do a GREP search \u\u+
- Change case to lowercase
- Apply SmallCaps (or: apply character style)
this would allow to search for acronyms and change them to smallcaps (or, even better: apply a character style with small caps and tracking)
I know it is easy for OpenType smallcaps (do a GREP search, change to OT smallcaps) but this doesn't really change case. And some fonts used aren't OT.
Anyone?
Would be VERY apreciated!!

But Harbs is a seasoned scripter who knows he'll get flamed if one of his scripts "just does not work" ;)
Well, now that you mention it, the script is not really foolproof. It's a quick and dirty script which I threw together very quickly. It's missing any error checking, some of the variables global, and it's not in a private namespace. These are all things which could cause it to "just not work" ;-)
Here's a more foolproof construct... (and it'll work on the current story if selected, or the whole document if there's no story selected) It will create a new character style if one does not exist and work on character styles within style groups as well. I wrapped the whole script in an anonymous function to give it a unique namespace as well.
(function()
if(app.documents.length==0){return}
var doc=app.documents[0];
// Change the following to your style name!
var character_style_name = 'Small Caps';
try{var range = app.selection[0].parentStory}
catch (err){var range = doc}
//comment out next line if you do not want styles.
var charStyle = GetCharacterStyle(character_style_name,doc);
app.findGrepPreferences = null;
app.findGrepPreferences.findWhat="\\u\\u+";
var finds=range.findGrep();
for (var i=0;i<finds.length;i++){
finds[i].changecase(ChangecaseMode.lowercase);
//comment out next line if you do not want styles.
finds[i].applyCharacterStyle (charStyle)
//uncomment next line if you do not want styles.
//finds[i].capitalization=Capitalization.smallCaps;
function GetCharacterStyle(styleName,doc){
var charStyles=doc.allCharacterStyles;
for(var i=0;i<charStyles.length;i++){
if(charStyles[i].name==styleName){
return charStyles[i];
return doc.characterStyles.add({name:styleName,capitalization:Capitalization.smallCaps});

The Strange Case of Change Case

My company's name is MCS. When I'm writing in caps, and then I want to re-use that text in sentence case I use Indesign's change case feature to change caps to sentence case. When ever my company's name is in the copy, I always have to go back and re-write it as upper case. I'm afraid that one day Ill forget to do it.
Is there a setting that I could choose so that this particular combination of letters is always written in caps?

MagicToaster wrote:
My company's name is MCS. When I'm writing in caps, and then I want to re-use that text in sentence case I use Indesign's change case feature to change caps to sentence case. When ever my company's name is in the copy, I always have to go back and re-write it as upper case. I'm afraid that one day Ill forget to do it.
Is there a setting that I could choose so that this particular combination of letters is always written in caps?
In Preverences > Autocorrect, enter the lowercase as wrong and uppercase as correct.
Enable Edit > Spelling > Autocorrect - a check mark indicates it's enabled.
An alternate is to create a text variable and insert it where needed. You can speed up inserting a text variable by using Quick Apply.
Search Google for terms like "InDesign autocorrect tutorial," "InDesign text variable," and "InDesign preferences," without quotes, for details.
HTH
Regards,
Peter
Peter Gold
KnowHow ProServices
Message was edited by: peter at knowhowpro

Bug: Change Case as you Type

For some reason the option "Change case as you type" (Preferences > Code Editor > Completion Insight) keeps changing. It will remain the same for a while but changes at some random point. Each time I restart SQL Developer it seems to go back to "+Lower Keywords, Upper Identifiers+".
Here's the information about the current version that I'm using:
Oracle SQL Developer 3.0.04
Version 3.0.04
Build MAIN-04.34
OS: Windows 7 - 64bit
Martin
http://www.ClariFit.com
http://www.TalkApex.com

Try to set it right also at Preferences - Database - SQL Formatter - Oracle - Edit - Other - Case change.
Hope that helps,
K.

NB300 - Changing background on Windows 7 Starter

Hey,
I have useless windows 7 starter on my nb300 and wan to know if there's a toshiba driver on my harddrive that will let me change my background picture as starter doesnt allow it. i dont want to buy an upgrade as i just bought the pc! Help!

Hi Jessywolfe,
Normally its not possible to change the background on Windows 7 starter so maybe an upgrade to Home Premium would be an option.
If you search with Google you will find good tutorials how to change the background. There is an additional program called *Oceanis Change Background Windows 7* that can change the background.
Check this!!!

Changing CAS e&m-wink-start to a PRI on voice gateway

Similar Messages

Maybe you are looking for