Chat not working after nokia C3-01 software update...

Chat not working after nokia C3-01 software update from 5.65 to nokia 6.00

when is there's gonna this be fixed it has been more than a month
satisfaction level is decreasing with the product

Similar Messages

Droid Pro not working after yesterday's system software update

I downloaded it last night and now my Outlook exchange mail account shows no messages. I can send an email from my Droid Pro Outlook account but it does not receive any.
Checked with corporate IT and there were no changes overnight to our corporate email system. My personal POP mail still works. Also Calendar is not syncing from corporate back to the Droid or from the Droid.
Even more disturbing is the phone is running Hot and I can not get the charge above 20%
I have restarted several times and all the settings are pre update.

Hello:
I think you interrupted the update. The behavior you describe happened to me as well, but the update eventually finished.
I would unplug the Apple TV for 30 seconds or so to see if that helps.
This article describes how to reset to factory settings:
http://support.apple.com/kb/HT4367
Barry
Message was edited by: Barry Hemphill

C1-01 not working after Nokia update

Hi,
C1-01 not working after Nokia update.
Message shows "Updating" then blank screen, any ideas?

How did you start the update? OTA or using Nokia Suite?
Try to run the update through Nokia Suite again.
If I have helped you, please hit the star at the bottom of my posts - it's appreciated!
Don't forget if your problem is solved to press the "Accept as Solution" button.

HT4623 my phone main button not working after installed new version software 7.0.6

my phone main button not working after installed new version software 7.0.6

Arrange some liquid like petrol spirit and w 40
two drops in to home button.
30 times press slowly slowly and then restart your apply iphone.
You will get ready.
I am sure. Thanking you...

HT5654 my ipad is not working i just install a software update after that it ask for restore ipad when i did that it show error 3194?

my ipd is stop working after i install a software updates it ask for restore ipad when i did that it show error 3194?

savvyfromvic wrote:
... error 3194?
Please see the More Like This section on the right.
Also... see item 3 Here > Community etiquette

GPS not working on Nokia C7 since Belle Update

GPS IS NOT WORKING SINCE NOKIA C7 IS UPDATED FROM ANNA TO BELLE.
ON ANNA IT WAS WORKING PERFECTLY FINE..
PLEASE GUIDE ME THE SOLUTION.

Hi matemale,
If you are using just Internal GPS, could be that the location information got wiped when you did the update. In this case give the device some time to get the location, this can take relatively long time (the first time), so little patience is needed.
If you are using AGPS and Network based navigation, then do the following actions and in between them test if the device works.
Make sure the internet is on in Maps > Options (3 lines) > Settings > General > Connection > Online. Also check that the network destination is correct.
Make a back up with Nokia Suite. Type in *#7780# = soft reset, no data lost.
You can also reinstall the phone software. The process is the same as when updating with Nokia Suite, but at the end select "Reinstall".
If it's still the same, type in *#7370# = hard reset, phone memory will be wiped. Restore back up.
Hope you get the navigation working again!
Jampe
If the answer solves your issue, please click the ACCEPT AS SOLUTION button so other users can benefit from it as well. Giving a kudos (the white star) if my answer has helped will be appreciated.

Car kit microphone not working after nokia softwar...

I have a Nokia 5800 Express Music. It was working perfect in my car Bluetooth system. Recently I updated my software version to 60.0.003. Now the microphone is not working while using the car Bluetooth system. I can hear the caller voice but they can’t listen what I say. All other phones are still working perfect with Bluetooth System. Therefore I think some bug is there with this software update. I tried changing Accessories settings to Headset, Wireless Car Kit etc., but still the problem exist.
Please me to find some way to make the mic working or else help me to downgrade my phone software to earlier version.

please somebody help.......

HDMI output not working after 1.0.8.6067 update on sharp LCD TV's

Have three TV's two of which are Sharps Aquos and the other is a Samsung. After updating to 1.0.8.6067 the Playbook cannot detect the two Sharps(each different model #'s) . I have three different cables that worked fine before the update and all three cables still work perfectly with the Samsung TV. This issue has been giving me trouble from when i got the device. I even sent the unit back to RIM and of course it was no fault found. About a month ago it suddenly started to work on the Sharps. i've been using the playbook daily on these TV's without incident until the latest software update. It now only works on the Samsung. Obviously something is going on with the playbook HDMI software driver. RIM support was unable to get it working reliable during my 3 month support window. Of course it started to work on the last day of my support but the recent update has put me back to square one. Any suggestions?
Tony

I have not had any issue with any brand TV yet
I dont remember if I tried a sharp on not. I do know that teh several Samasung ones worked fine.
Click here to Backup the data on your BlackBerry Device! It's important, and FREE!
Click "Accept as Solution" if your problem is solved. To give thanks, click thumbs up
Click to search the Knowledge Base at BTSC and click to Read The Fabulous Manuals
BESAdmin's, please make a signature with your BES environment info.
SIM Free BlackBerry Unlocking FAQ
Follow me on Twitter @knottyrope
Want to thank me? Buy my KnottyRope App here
BES 12 and BES 5.0.4 with Exchange 2010 and SQL 2012 Hyper V

Sound not working after 10.9.4 Mavericks Update - HELP!

My sound does not seem to be working following the latest update to Mavericks (10.9.4). I am running a 2012 Retina Macbook Pro. Sound does not work with speakers, headphones or built-in sounds. Before anyone asks, no its not on mute, I have checked the Audio Midi setup and Sound settings and everything is as they were prior to the update, so the sound should still be working.
I have tried resetting the SMC and PRAM, no luck yet. Also tried re-installing the update but did not work.
Any help is greatly appreciated!

So I had the same problem; Actually other problems occurred after upgrade 10.9.2 (Thunderbolt related issues) and now after upgrading to 10.9.4 my internal sound disappeared.
The solutions described above made it worse; Sorry sykosoft .. but your solutions is even dangerous ;
I spend almost a Day finding out how to restore my internal audio devices ..
So what I discovered, this is a software issue;
Update on update on update without any clean install resulted in some filty .plist files
com.apple.audio.DevicesSettings.plist
com.apple.audio.SystemSettings.plist
looking in those files I discovered some settings pointing towards RabbitEars .. perhaps I tried it once in a previous life but now I do believe the upgrade took by incident the wrong 'device' as standard ..
So I looked up and the only thing I could do was finding .kext and other related stuff .. only able to remove it commando wise = terminal
after rebooting for the 722th time performing a SMC and PRAM for the 666th time the result was ... NO STANDARD devices detected
THe only solution working is :
A recovery install;
https://www.apple.com/osx/recovery/
In my case I encountered a problem; My recovery failed (reboot press and hold CMD+R, selecting install fresh OS X)
I find out it was due to my FileVault encrypted HD; So first I uncrypted (switched off FileVault) my HD, and even created a USB recovery disk (not needed)
Tadaaaa 45 minutes later all problems solved, without loosing data or reinstalling all programs ..
*feeling relieved* I thought sharing my pain and solution would save you hours finding out how to repair, hoping PRAM and SMC reset would solve it ..

Facetime, iMessage, and Mail not working after iOS 6.1.3 update

I've had my iPod touch 4th generation since Oct 2010 and never updated the iOS until very recently. Before the update, Facetime worked consistently and easily. After I finally got around to updating my iOS a week ago, my iPod has come into severe issues.
99% of the time, I cannot send or receive Facetime calls. If I try to make a call, it doesn't make the dial tone and eventually it just says "Connection Lost". Nothing happens if someone is trying to send me a call. I only Facetime with my boyfriend and his iPod hasn't changed since Facetime was last working. HIs other iPod is also updated with iOS 6.1.3.
I never used iMessage before the iOS update, but because it says on Apple support that it uses push notifications like Facetime does, so I tried it. Most of the time, I cannot send or receive messages. I rarely used Mail before the update, but I never had a problem with it. Now, when I enter my gmail password, it keeps saying my username and password are not correct, even though I haven't changed my credentials.
I only use my iPod for Facetime, iTunes, and Pandora. I don't need iMessage or Mail, but I am testing with those to see if this can help find the root cause of the problem. Pandora works smoothly so I know it's not a wifi connection issue. I have searched for remedies on end and tried:
1. Reset, turn off/restart, turn Facetime on and off, etc.
2. Changing the DNS server address to 8.8.8.8, which made Facetime work normally for one time and never again
3. Updating my Apple ID password online, then signing out and signing back in
4. Creating another Apple ID with my other gmail account. Maybe 1 out of 10 Facetime call attempts, I can generate the dial tone, but when my boyfriend clicks to receive the call, it says that I am unavailable. iMessage has about the same success rate. It seems when I miraculously can send or receive texts through iMessage, I can manage to get the dial tone when I try Facetime, though the call cannot go through.
This is of course extremely frustrating and I highly regret the update now. I was hoping for an improved iPod after the update, and now I have a near-dud! I did make sure to check my location and date and time, and both are correct (US, Central time). Any help would be greatly appreciated. Thank you.

I spoke too soon. I tried Facetime again last night and had the same problems. Another factory reset did not work. I think it may be time to just call Apple support.

Earbuds with Mic and Skip Functions not working after IOS 6.0.1 update?

I have earbuds with a mic and skip buttons functions and noticed that mic and the skip music functions stop working after updating to IOS 6.0.1. Now when I talk on the phone the mic on iPhone itself is working and not the mic on my earbuds. Also when playing music he skip functions has stop working. Has anyone noticed these problems?

Phone restart > if that doesn't work then do a reset of the settings. Full restore would be the last option.

Lighting cables and adapters are not working after the last iOS 7 update.

Looking for some help from Apple here. After the last iOS 7 update, some of my lightning cables and adapters have stopped working.
I have an iPhone 5 funning iOS 7.0.2.
I have a car charger/FM RF transmitter that has worked like a charm for years. Because none of these have been made with a lighting connector, I've had a genuine Apple adapter on it since I bought my iPhone 5 a year ago. Never had a problem until the last iOS update. Now when I plug it in, not connection is registered. I've verified the charger is working by removing the adapter and plugging the old iPhone connecting into an iPhone 4 running iOS 6. I've also verified the adapter is working by plugging the charger with adapter into an iPad mini running iOS 6.
I also have a Belkin USB car charger. This came with a black lighting cable. Also worked like a charm until the last update. Now, half the file when I plug it in, no conncetion is registered. The other half of the time, it says this cable is not supported but does not connect my phone or charge it. I've also verified that the cable is working by plugging it into an iPad mini running iOS 6.

I had the same bug. Powering off the phone and back on resolved the issue

Mac mail not working after OS 10.9.5 update

I have the same problem as other users.
Since last update of the OS to 10.9.5, the MAIL app does not send email.
It just does a few times a day, on and off.
I tried to take all accounts offline and then take all accounts online again, so many times, does not work.
I tried to reboot; does not work.
I tried deleting my accounts and creating them again, does not work.
I started to like that app, makes me sad to see how bad it got this week.
Does anyone know what is going on??
MacBook Air, OS X Mavericks (10.9.5)
HELP!
Re: Mail app drives me crazy, does not sync since last update 10.9.5

On and Off, that's the reason I am 100% convinced it is a software update issue.
It seems that Mail does not connect to servers as it used to.
Sometimes it would work great for a while, and turn back down again for no reason.
Apple will not read those comments as it is a place for mac users only. The only thing we can do is send 1 email per day, that's what i am doing, to "Provide Mail Feedback" in Mail on the bar to complain so they hear about the problem and try to solve it.
Any mac user of the community could help, apart from saying just do not use this app anymore?

Links to shortcuts not working after applying 8.2.4 update

After the 8.2.4 update was installed on my Vista computer, I can’t invoke links in my PDFs that specify an UNC\\pathname\shortcut.lnk. The hyperlink was originally created in Microsoft Office 2007. The file was then converted to PDF using the Adobe Acrobat add-in “Create PDF”. The error I’m getting is something like “Windows cannot find ‘shortcut.lnk’ could not open file ‘/UNC/pathname/shortcut.lnk’. Please note that these links work as expected on 8.2.3 and lower. Were new registry keys added? Was a bug introduced into the update? I’m lost…

A lot of people have been reporting broken links with the latest update, and it appears to be a bug that Adobe is reported to be working on.

Port Forwarding not working after 7.7.1 Firmware update

I bought the new 6th generation Airport Extreme today, and after I set it up, everything worked great. I have a VoIP phone that needs to have traffic on port 5060 forwarded to it, and that worked just fine as well.
However, I then updated to the 7.7.1 firmware, and the port forwarding stopped working. I tried a hard reset of the Airport and re-entered all the settings, but it still didn't work. I spent about 30 minutes on the phone with 2 Apple support people who tried hard, but couldn't help. They also couldn't find a way to download the 7.7 firmware, so there was no way to downgrade. They suggested I go back to the store and exchange it for another one, which I did, and now it all works again.
Has anyone else had issues with port forwarding on 7.7.1? I'm just wondering how I'll ever be able to update the firmware, since failure means having to get a new Airport.

Huh,
turns out the problem went away with another restart of the Mac Mini. I'm still uneasy about it though, as I do not understand how it went from working to not-working over night in the first place. But, at least for now, the problem seems gone.
Thanks for commenting.
Cheers
Niels Olof

Chat not working after nokia C3-01 software update...

Similar Messages

Maybe you are looking for