Cinema Display 30" and MBP - No Picture

I have a 2.16 Core Duo Macbook Pro 17". Today I purchased a 30" Cinema Display at the Apple store.
Because of issues I had heard about I had the Apple employees help me open the box and plug in the monitor to a Macbook Pro on the floor to check for dead and hot pixels and other screen problems. None found. I was so psyched!
I get it home and set it up. I run the DVI cable over to my Macbook Pro and nothing... The MBP screen goes blue and then refreshes when the monitor is attached or detached like it detects it, but under system profiler it never registers an additional display (and I did refresh the info). The soft power button on the Cinema Display triggers my computer to give me the shut down/sleep dialog so something is registering.
Basically everything works on the display but the picture. I just get a black screen. I hooked up my wife's G4 1.67 and it drives the screen just fine with a picture.
Any thoughts?

I have owned a MacBook Pro (15" / 2.16GHz / 2GB) and 30" Cinema HD Display since September 2006.
The display's DVI, USB, and FireWire cables are all connected to the MacBook Pro. A keyboard (with mouse) and iPod dock are connected to the display's USB ports, and two LaCie D2 drives are connected to the display's FireWire ports.
The display has remained blank at start-up on two occasions, both since upgrading to Mac OS X 10.5, though that may be coincidental. In any event, unplugging the display's USB cable from the MacBook Pro had the effect of waking the display; plugging the display's USB cable back into the MacBook Pro put the display to sleep.
Try disconnecting the USB and FireWire cables from the MacBook Pro and unplugging any peripherals attached to the display. I found that everything worked fine when reconnected.

Similar Messages

Using only an Apple Cinema Display connected to MBP (w/ the lid closed)

Hi,
Could someone please help me on a small but rather annoying problem?
I have a Mac Book Pro 17" connected to an Apple Cinema Display 24". All I would like to do is to just use the Cinema Display, close the laptop lid, and for the MBP not to go into sleep mode (taking the Apple Display away with it).
I've looked in the Display and Energy Saver settings and have trawled through the online forums but as yet have not had any luck.
Can someone point me in the right direction?
Many thanks, M>/.

Apple supports using an external keyboard/mouse to wake the MBP in clamshell mode.
http://support.apple.com/kb/HT3131
The other option is 3rd party software to disable lid-closed sleep:
InsomniaX
SleepLess

27 LED Cinema Display Audio and Brightness when powering MacBook Pro

When my 27 LED Cinema Display is powering my (or another) 2009 13" MacBook Pro, I have experienced three issues:
1. The dropped audio problem other users have mentioned. Shutdown, then disconnect power/usb/displayport, then wait ~15s, then reconnect and reboot temporarily fixes the problem.
2. I also have the sluggish keyboard behavior when adjusting the volume that others have mentioned.
3. I have experienced shifts in display brightness which are obvious when the display is dimmed. I have disabled the ambient light sensor as well as any interfering power management or energy saver settings. Opening apps, scrolling and other normal activities seem to aggravate this behavior.
This last strange behavior inspired me to try using a power adapter for the MacBook Pro instead of display's laptop power connector. *Doing so seems to have resolved all three issues.*
It seems that this may indicate an underlying problem with the display's power supply. Can anyone confirm?

mmayo wrote:
I am having the same issues & with a 1 day old display. I am using a 15" MBP. The screen is killing me when it dims down when no lights are on. I didn't notice the issue when the screen is brighter with the lights on. Anyone know if this is a hardware or software issue? I'd like to utilize the ambient light sensor but not if its going to make my screen flicker when it is dim....
(1) I have never had any deaths associated with my screen, but on rare occasions my display's brightness will flicker when I manually adjust the brightness. The fix I have found for this is to increase the brightness one more setting or decrease it one more setting. Changing the screen from full dim to full bright and then setting the brightness I want sometimes helps, too.
(2) You can check whether this software update has been applied to your 27-inch:
http://support.apple.com/kb/HT4293
(3) Your Apple Service Provider could tell you whether your problem is related to hardware or software.
Mac Pro Quad Core (Early 2009) 2.93Ghz Mac OS X (10.6.4); MacBook Pro (13 inch, Mid 2009) 2.26GHz (10.6.4)
LED Cinema Display; G4 PowerBook 1.67GHz (10.4.11); iBookSE 366MHz (10.3.9); External iSight; iPod touch 4.1

Macbook Air - using Cinema Display usb and firewire?

Hello,
This is the first post for me, however the answer will determine whether I make the jump for an air.
Will the usb hub on the cinema displays work with the macbook air dvi output connector. (essential for me to purchase) would firewire work (bonus if it does)
Unfortunately I have to have ethernet connection because of the setup in my office, and some of the software I use has usb hardware dongles. The ethernet adapter is fine but I also need usb.
When I am on the go the single usb will suffice.
Any advice would be really appreciated.

USB hub works fine on my 23 Cinema display with the Air, haven't tried the others but I use the USB on display to plug in my mobile broadband ( live out in the sticks and don't get cable or DSL ) and it lets me switch between my Air and MB Pro fine.

23" cinema Display flickers and goes to black

Hey all,
I am running two 23" cinema displays and one of them is flickering and going to black. Here is a video of it.
http://larskoerkemeier.com/MVI_0972.MOV
The curved bands arent there thats just from the filming but what happens is the entire image shifts up very quickly and what you see flash on the bottom is actually the top. It repeats this a couple times and then turns off and then it repeats and after a couple times the display just stays off.
System:
Model Name: Mac Pro
Processor Name: Dual-Core Intel Xeon
Processor Speed: 2.66 GHz
Memory: 6 GB
Graphics Card: NVIDIA GeForce 7300 GT
Thanks,
-Lars

Hi-
Try switching the power adapters to see if the problem moves to the other display.
Of course, reconnecting/double checking all connections is a good idea.
Other than that, any references in Console/Logs regarding graphics driver errors?

Older Apple HD Cinema Display is detected but no picture

Forgive me, as I know this is an often-asked question but I have searched and can't find a response that fixes the issue.
Yet.
So I have a Mac Pro (circa 2008) that works fine. The Apple Cinema Display is even older from about 2004 (I think).
Everything was working fine and I was video editing and Photopshopping to my hearts content.
I had noticed that recently the display would not come back from sleep without rebooting the computer.
So that might have been an early clue.
Then this morning I came home from taking the kids to school and the Mac Pro fan was running loud and no image on screen.
I rebooted the computer. This time the monitor displayed black and white vertical lines.
"Oh joy," thought I.
I rebooted again.
This time nothing but the heart of darkness.
Nothing.
I reseated the video card (as that has been a culprit in the past) and rebooted. Still no image. Did all the PRAM, unplugging the computer, waiting a minute plugging back in, plus all the other keyboard tricks one reads about. Still no joy.
I then tried the monitor on my MacBook Pro to see if it was a computer issue or monitor issue. No image from the MacBook Pro either.
The Macbook Pro did detect the display though and showed it along side theMacbook Pro screen is the Display Prefences.
I also ran the MacBook Pro in Traget Mode to the laptop so i could run diagnostic checks and repairs uisng Apple Utilities and Disk Warrior. No problems were detected on the Mac Pro (tower).
I then connected a Samsung monitor (that the kids watch Netflix on) and that worked fine on both the laptop and the Mac Pro tower.
So I have isolated the cause to the Apple HD Cinema Display. The video card and other hardware tested out fine.
Any thoughts on a fix or what the issue might be?. I can get by with Samsung as I am on deadline - but would rather have my trusty Apple Cinema screen back.
Many thanks.
And good karma to all who give it a head scratch.
A

Yeah I use my screen saver more often now and yes it's the white windows and desktop icons that ghost the most not horrible and my warrant is a few years past. The genius is wrong to accuse you that's just plain silly. The first apple 30 inch I bought had green lines and after a few trips to the store they sent it off to be repaired but in the end I think I got a different monitor back. Three and a half years later this started to happen. It's like short term burn and it's pretty subtle. I'm an audio guy so if I were a graphics person and this was my main rig I would be more upset. I just hope it does not continue to get worse. I have an older 22 inch with the clear plastic and it does not have the issue. It only starts to do it after it's been n for few hours.
Good to know I'm not the only one, thanks for posting.

24" Cinema Display flickering and eventually going dark

I am having a repeat of a problem with my Apple 24" Cinema Display. The symptoms are the display will go black and come back on (flicker) and sometimes it takes a few seconds for it to come back. All USB devices connected to the Cinema Display become disconnected from my MacBook Pro when this happens.
Last time this happened it started slowly and as time passed it happened more frequently. When I brought it into the store they were able to reproduce the problem immediately. They replaced the logic board in the monitor.
I contacted support again. The display is still under warrantee. They scheduled an appointment for me to bring the display in. I am seeing the same behavior where the frequency of this problem increases as time passes.
I am concerned they will be unable to quickly reproduce the problem again and not fix it, or fix it and the problem will come back again in a few months. I am afraid that I will still be having this problem after the warrantee expires.
I've purchased many displays over the years (including Apple) and this is the first time I have ever had a problem. I think I may have had a lemon.
I originally posted in these now archived threads:
http://discussions.apple.com/thread.jspa?messageID=12175983#12175983
and
http://discussions.apple.com/message.jspa?messageID=12311032#12311032

Just a quick update. I brought the display into my local Apple store. After they reviewed the records from the previous repair and my description of the problem they believe it could be a power supply problem inside the monitor. The power supply may have caused the logic board to go bad. Replacing the logic board last time fixed the problem but the bad power supply ended up causing the problem to return.
I let them know that I was concerned that this is a reoccurring problem and my warrantee expires in July. I don't want to see this problem come back after the warrantee expires.
I'm not sure what they will do if that happens. I hope this problem gets fixed this time around.

27" LED Cinema Display – noise and buzz

Hello,
I recently purchased a second hand 27" Apple LED Cinema Display, and I now started to have some issues.
The first issue started today, it is some kind of buzz that comes out of the right speaker whenever I lower the brightness of the screen. I have about the opposite happening for other people – whenever the brightness would be above 3/4, a buzz sound would come up. For me it's when the brightness is below 1/4. The lower the brightness, so higher the pitch of the buzz. How weird is that?
The second issue is that, whenever a sound is played, some kind of white noise starts coming from I believe both speakers of the display. Even if I just adjust the volume on the keyboard (which makes a sound as well), this white noise would come up. It would last around 15-30 seconds, and then it would disappear. If headphones are connected to the Mac Pro, it doesn't happen (and it can't be heard in the headphones either). I once hooked up the Mac Pro to a Panasonic TV to test, and there was no buzz coming from the TV either.
Now I just noticed that the white noise is constantly here since the buzz appeared today (when I lower the brightness). Something is failing here I believe. It could also be the graphics card I guess?
Sometimes I get a very quick weird flash on the screen (black & white stripes I believe) for half a second, then they're gone. It's quite rare so it's hard to troubleshoot. Maybe it has to do with the Cinema Display as well. Or perhaps it is my graphics card (It's a Sapphire HD 7950 3 GB – the Cinema Display is connected with Mini DisplayPort). Or it might just be bad drivers for this card – they were never that good apparently.
Perhaps someone knows more than I do
All helps is appreciated…
Cheers!

No ideas?

24in LED Cinema Display not charging MBP Late 2011

Hello All,
My new Macbook Pro (Late 2011) will not charge when connected to my 24in LED Cinema Display. The power indicator on the menu bar says "Not Charging" and the LED in the magsafe cable is dim. Is this a known limitation of the older Cinema Displays?
Thanks,
c.

I had the same problem. I found this
https://discussions.apple.com/thread/2006045?start=0&tstart=0
.. which suggestes "wiggling" the magsafe connector a little. It worked for me.

New Cinema Displays compatible with MBP 17 inch Core 2 Duo?

Hi, I want one of the new Cinema Displays to act as external monitor for my 4 year old Macbook Pro 17 inch Core 2 Duo. Is there a dongle adaptor yet that will connect the display's Mini DisplayPort with my computer's Dual Link DVI? Or am I SOL.?
Thanks

A component such as this one can be used to connect that display to a DVI port.
(52211)

30" Cinema Display Vsync and Hsync

What are the hsync and vsync values for the 30" display? I'm using it with my linux computer as well, and I'm not sure what to tell it.

Here is a text dump from the EDID contained on a Cinema 30's ROM. The first timing is suitable for single-link DVI and results in a low resolution. The second timing is the Cinema's full resolution but it only works for dual-link DVI enabled graphics cards.
Descriptor #0 is Timing definition:
Mode = 1280 x 800 @ 60Hz
H. Active...............1280 pixels
H. Blanking.............160 pixels
V. Active...............800 lines
V. Blanking.............23 lines
HSync Offset............48 pixels
HSync Pulse Width.......32 pixels
VSync Offset............3 lines
VSync Pulse Width.......6 lines
Pixel Clock.............71.00MHz
Horizontal freq.........49.31kHz
Vertical freq...........59.91Hz
H Image Size............641mm
V Image Size............401mm
H Border................0 pixels
V Border................0 lines
Non-Interlaced
Sync: Digital separate with
* Positive vertical polarity
* Negative horizontal polarity
Descriptor #1 is Timing definition:
Mode = 2560 x 1600 @ 60Hz
H. Active...............2560 pixels
H. Blanking.............160 pixels
V. Active...............1600 lines
V. Blanking.............46 lines
HSync Offset............48 pixels
HSync Pulse Width.......32 pixels
VSync Offset............3 lines
VSync Pulse Width.......6 lines
Pixel Clock.............268.00MHz
Horizontal freq.........98.53kHz
Vertical freq...........59.86Hz
H Image Size............641mm
V Image Size............401mm
H Border................0 pixels
V Border................0 lines
Non-Interlaced
Sync: Digital separate with
* Positive vertical polarity
* Negative horizontal polarity

IMovie displaying incorrect and mixed up pictures

I am currently creating a project that consists of a number of still frames. Unfortunately, when I insert a picture whether from finder or iPhoto, the incorrect picture is often inserted. How can I fix this?

Hello, I see this post is pretty old, but in case you're still having this issue, or if anyone else lands here, there are some workarounds/fixes and helpful hints for this bug over in this thread.

MBP and LED Cinema Display Color Washed Out After Screen Saver

When coming out of screen saver, often the color profile on either my LED Cinema Display or the MBP LCD is messed up. The color looks washed out. Simply going to the Color tab in the Displays preference pane fixes this.
How do I get this to stop?
Thanks,
Bobby

My 13" MBP has now started to do the same thing as described. The thing is, it has never done this since I bought it in late July 2009. I have iWork installed, Firefox, Skype, and Pixelmator. I may have a clue, however, for the Apple people: my MBP never did this until last night and this morning. The only thing I changed yesterday was removing the 2 gig of memory and installing 4 gig. I also tried the translation widget for the first time.

Mid-2012 MBP with 27" Cinema Display SCREEN GOES BLACK WHEN USING USB PERIPHERALS IN DOCK

I haven't been able to find any straightforward answer as to why this is happening and it's becoming one of the most infuriating things in my life, impeding my workflow and costing me unmeasurable time in waiting, rebooting, screwing with cables, etc.
I use my MBP as a DAW for multitracking live audio events to ProTools through a digital console where I work. Here's my gear list that I use every day:
Mid-2012 MBP - Yosemite, 8GB, i7 quad 2.5, mechanical hd
HengeDocks dock for my exact model machine - has set-screw jacks for CinemaDisplay power, Tbolt, FW800, USB, USB, SDcard, headphones, etc
USB wired keyboard
Anker 1x4 USB3.0 hub - I have a TimeMachine 1TB drive, 3TB project backup drive, audio interface and MIDI I/O or PT iLok, depending what I'm working on
Magic Mouse (BlueTooth)
Here's what's happening:
SCENARIO 1 - I insert the CinemaDisplay (cD) power connector and TBolt plugs into the dock, tighten the set screws, close the lid of my MBP (already logged into Yosemite & linked with MagicMouse [mM]) and stick the MBP into the dock... everything comes up on the cD and I can go about my day. At this point, I can plug the USB hub into the back of the cD and the system sees the hub & all peripherals listed just fine.
SCENARIO 2 - Install cD powercon, TBolt connector, USB3 hub, USB keyboard into the dock, close the lid on MBP (again, logged in), insert into dock... cD comes up, looks great for about 15 seconds then goes completely blank. No response from key presses, mouse clicks, threats with a hammer, etc. Then, of course, I have to yank the MBP out of the dock, which hard-disconnects the external drives (backup and TimeMachine... good for them, right?) and causes the MBP to flake, thinking it's still in the dock, then not, then logging me out & requiring a password (not a big deal- I deal with copyrighted stuff, so passwords aren't the issue).
***EVEN IF I DO NOT PLUG THE USB3 HUB INTO THE HENGE DOCK, THE cD STILL GOES BLANK AFTER 15 SEC... IT ONLY SEEMS TO LIKE THE TBOLT AND POWER... NO OTHER PERIPHERALS (fw800, USB, etc)***
It seems like the MBP freaks out when the lid is closed and there are USB/FW peripherals plugged in while using a secondary TBolt display as the main output... seems stupid... if I need a closed-lid dock, the MBP shouldn't care what I have plugged in while the lid is closed. I had the same issues with Mountain Lion & Mavericks and now it's being repeated with Yosemite.
My goal in this exercise is simply to free up the USB jacks on the back of the cD for two reasons - #1) from time to time, I have extra things to plug in and I don't want some massive USB 1x8 hub on my desk... looks stupid; #2) the bottleneck created by plugging in the hub to the back of the cD (another hub via TBolt) almost triples the time required to back up/copy files. I move files from system drive to backup drive & back VERY often due to the nature of my job... speeding up this process would greatly improve my efficiency in the matter. Why would Henge create a dock with all the jacks on it to allow someone to plug into a cD that won't frickin work with said cD? Every other dock I've found makes the user stick the MBP on a slanted, goofy-looking stand and have the lid open or something dumb like that... what I have is the setup I need... just need the USB stuff to work while lid is closed and everything from powercon & cD to USB3 hubs will work without making the cD freak out.
Any ideas out there?

Have now taken the 27" display into the repair shop and after 24 hrs got the phone call - "appears to be nothing wrong with it, will check again on Tuesday and let you know".
I can't seem to find anything on the net describing a similar problem. Everything is working fine right now with the Mac Pro connected to the older 20 inch Cinema Display. In fact, everything seems to be working about a second faster.
I was told by the local retailer that Apple no longer makes the 27 inch LED Cinema Display product and the new display, the "Thunderbolt" will not work with my 13 month old Mac Pro.
***??? In 20 years of owning Mac equipment, this is my first major "uh-oh".

How to Connect Early 2011 MBP 13" to Apple 20" Cinema Display at 1680x1050?

My early 2011 MacBookPro will only display 1280x800 on an external Apple 20" Cinema Display. The MBP's specs say that it will support dual displays and video mirroring simultaneously at full native resolution on the built-in display and up to 2560x1600 on an external display. The 20" Cinema Display specs indicates that it supports an optimum resolution of 1680x1050. The 20" display is connected to the MBP through it's Thunderbolt port using an Apple Mini Display Port to DVI connector. No luck.
I've tried using the latest version of SwitchResX set to 1680x1050. It says it is configured to 1680x1050 but the display does not respond.
Anyone had success setting up this combination of MPB and Cinema Display at the max resolution of 1680x1050?

To clarify. The MacBook Pro displays 1280x800 and the Apple Cinema Display mirrors it at 1280x800. I cannot get the ACD to display at it's max capable resolution of 1680x1050.
The MPB has 16GB ram so 512 SDRAM is available to the Intel HD Graphics 3000 chipset.

Cinema Display 30" and MBP - No Picture

Similar Messages

Maybe you are looking for