Cisco 2702 not joining controller
Controller code vs. 7.6.120.0
From the controller:
(Cisco Controller) >debug capwap packet enable
Warning! Enabling this debug with large number of AP's connected, May flood console with message logs !!!.
Are you sure you want to continue? (y/N)y
(Cisco Controller) >*spamApTask3: Mar 05 13:38:13.317: <<<< Start of CAPWAP Packet >>>>
*spamApTask3: Mar 05 13:38:13.317: CAPWAP Control mesg Recd from 192.168.1.28, Port 43295
*spamApTask3: Mar 05 13:38:13.317: HLEN 4, Radio ID 0, WBID 1
*spamApTask3: Mar 05 13:38:13.317: Msg Type : CAPWAP_DISCOVERY_REQUEST
*spamApTask3: Mar 05 13:38:13.317: Msg Length : 165
*spamApTask3: Mar 05 13:38:13.317: Msg SeqNum : 0
*spamApTask3: Mar 05 13:38:13.317:
*spamApTask3: Mar 05 13:38:13.317: Type : CAPWAP_MSGELE_DISCOVERY_TYPE, Length 1
*spamApTask3: Mar 05 13:38:13.317: Discovery Type : CAPWAP_DISCOVERY_TYPE_UNKNOWN
*spamApTask3: Mar 05 13:38:13.317:
*spamApTask3: Mar 05 13:38:13.317: Type : CAPWAP_MSGELE_WTP_BOARD_DATA, Length 62
*spamApTask3: Mar 05 13:38:13.317: Vendor Identifier : 0x00409600
*spamApTask3: Mar 05 13:38:13.317: WTP_SERIAL_NUMBER : AIR-CAP2702I-A-K9
*spamApTask3: Mar 05 13:38:13.317:
*spamApTask3: Mar 05 13:38:13.317: Type : CAPWAP_MSGELE_WTP_DESCRIPTOR, Length 40
*spamApTask3: Mar 05 13:38:13.317: Maximum Radios Supported : 0
*spamApTask3: Mar 05 13:38:13.317: Radios in Use : 0
*spamApTask3: Mar 05 13:38:13.317: Encryption Capabilities : 0x00 0x01
*spamApTask3: Mar 05 13:38:13.317:
*spamApTask3: Mar 05 13:38:13.317: Type : CAPWAP_MSGELE_WTP_FRAME_TUNNEL, Length 1
*spamApTask3: Mar 05 13:38:13.317: WTP Frame Tunnel Mode : NATIVE_FRAME_TUNNEL_MODE
*spamApTask3: Mar 05 13:38:13.317:
*spamApTask3: Mar 05 13:38:13.317: Type : CAPWAP_MSGELE_WTP_MAC_TYPE, Length 1
*spamApTask3: Mar 05 13:38:13.317: WTP Mac Type : SPLIT_MAC
*spamApTask3: Mar 05 13:38:13.317:
*spamApTask3: Mar 05 13:38:13.317: Type : CAPWAP_MSGELE_VENDOR_SPECIFIC_PAYLOAD, Length 10
*spamApTask3: Mar 05 13:38:13.317: Vendor Identifier : 0x00409600
*spamApTask3: Mar 05 13:38:13.317:
IE : UNKNOWN IE 207
*spamApTask3: Mar 05 13:38:13.317: IE Length : 4
*spamApTask3: Mar 05 13:38:13.317: Decode routine not available, Printing Hex Dump
*spamApTask3: Mar 05 13:38:13.317: 00000000: 01 00 00 01 ....
*spamApTask3: Mar 05 13:38:13.317:
*spamApTask3: Mar 05 13:38:13.317: Type : CAPWAP_MSGELE_VENDOR_SPECIFIC_PAYLOAD, Length 22
*spamApTask3: Mar 05 13:38:13.317: Vendor Identifier : 0x00409600
*spamApTask3: Mar 05 13:38:13.317:
IE : RAD_NAME_PAYLOAD
*spamApTask3: Mar 05 13:38:13.317: IE Length : 16
*spamApTask3: Mar 05 13:38:13.317: Rad Name :
*spamApTask3: Mar 05 13:38:13.317: AP1c6a.7aba.91ec
*spamApTask3: Mar 05 13:38:13.317: <<<< End of CAPWAP Packet >>>>
*spamApTask3: Mar 05 13:38:13.317: 1c:6a:7a:ba:91:e0 Discovery Request from 192.168.1.28:43295
*spamApTask3: Mar 05 13:38:13.317: 1c:6a:7a:ba:91:e0 Join Priority Processing status = 0, Incoming Ap's Priority 1, MaxLrads = 5, joined Aps =0
*spamApTask3: Mar 05 13:38:13.317: apModel: AIR-CAP2702I-A-K9
*spamApTask3: Mar 05 13:38:13.317: apType = 41 apModel: AIR-CAP2702I-A-K9
*spamApTask3: Mar 05 13:38:13.317: 1c:6a:7a:ba:91:e0 Discovery Response sent to 192.168.1.28 port 43295
*spamApTask3: Mar 05 13:38:13.317: 1c:6a:7a:ba:91:e0 Discovery Response sent to 192.168.1.28:43295
*spamApTask3: Mar 05 13:38:13.317: <<<< Start of CAPWAP Packet >>>>
*spamApTask3: Mar 05 13:38:13.318: CAPWAP Control mesg Recd from 192.168.1.28, Port 43295
*spamApTask3: Mar 05 13:38:13.318: HLEN 4, Radio ID 0, WBID 1
*spamApTask3: Mar 05 13:38:13.318: Msg Type : CAPWAP_DISCOVERY_REQUEST
*spamApTask3: Mar 05 13:38:13.318: Msg Length : 165
*spamApTask3: Mar 05 13:38:13.318: Msg SeqNum : 0
*spamApTask3: Mar 05 13:38:13.318:
*spamApTask3: Mar 05 13:38:13.318: Type : CAPWAP_MSGELE_DISCOVERY_TYPE, Length 1
*spamApTask3: Mar 05 13:38:13.318: Discovery Type : CAPWAP_DISCOVERY_TYPE_STATIC_CONFIG
*spamApTask3: Mar 05 13:38:13.318:
*spamApTask3: Mar 05 13:38:13.318: Type : CAPWAP_MSGELE_WTP_BOARD_DATA, Length 62
*spamApTask3: Mar 05 13:38:13.318: Vendor Identifier : 0x00409600
*spamApTask3: Mar 05 13:38:13.318: WTP_SERIAL_NUMBER : AIR-CAP2702I-A-K9
*spamApTask3: Mar 05 13:38:13.318:
*spamApTask3: Mar 05 13:38:13.318: Type : CAPWAP_MSGELE_WTP_DESCRIPTOR, Length 40
*spamApTask3: Mar 05 13:38:13.318: Maximum Radios Supported : 0
*spamApTask3: Mar 05 13:38:13.318: Radios in Use : 0
*spamApTask3: Mar 05 13:38:13.318: Encryption Capabilities : 0x00 0x01
*spamApTask3: Mar 05 13:38:13.318:
*spamApTask3: Mar 05 13:38:13.318: Type : CAPWAP_MSGELE_WTP_FRAME_TUNNEL, Length 1
*spamApTask3: Mar 05 13:38:13.318: WTP Frame Tunnel Mode : NATIVE_FRAME_TUNNEL_MODE
*spamApTask3: Mar 05 13:38:13.318:
*spamApTask3: Mar 05 13:38:13.318: Type : CAPWAP_MSGELE_WTP_MAC_TYPE, Length 1
*spamApTask3: Mar 05 13:38:13.318: WTP Mac Type : SPLIT_MAC
*spamApTask3: Mar 05 13:38:13.318:
*spamApTask3: Mar 05 13:38:13.318: Type : CAPWAP_MSGELE_VENDOR_SPECIFIC_PAYLOAD, Length 10
*spamApTask3: Mar 05 13:38:13.318: Vendor Identifier : 0x00409600
*spamApTask3: Mar 05 13:38:13.318:
IE : UNKNOWN IE 207
*spamApTask3: Mar 05 13:38:13.318: IE Length : 4
*spamApTask3: Mar 05 13:38:13.318: Decode routine not available, Printing Hex Dump
*spamApTask3: Mar 05 13:38:13.318: 00000000: 01 00 00 01 ....
*spamApTask3: Mar 05 13:38:13.318:
*spamApTask3: Mar 05 13:38:13.318: Type : CAPWAP_MSGELE_VENDOR_SPECIFIC_PAYLOAD, Length 22
*spamApTask3: Mar 05 13:38:13.318: Vendor Identifier : 0x00409600
*spamApTask3: Mar 05 13:38:13.318:
IE : RAD_NAME_PAYLOAD
*spamApTask3: Mar 05 13:38:13.318: IE Length : 16
*spamApTask3: Mar 05 13:38:13.318: Rad Name :
*spamApTask3: Mar 05 13:38:13.318: AP1c6a.7aba.91ec
*spamApTask3: Mar 05 13:38:13.318: <<<< End of CAPWAP Packet >>>>
*spamApTask3: Mar 05 13:38:13.318: 1c:6a:7a:ba:91:e0 Discovery Request from 192.168.1.28:43295
*spamApTask3: Mar 05 13:38:13.318: 1c:6a:7a:ba:91:e0 Join Priority Processing status = 0, Incoming Ap's Priority 1, MaxLrads = 5, joined Aps =0
*spamApTask3: Mar 05 13:38:13.318: apModel: AIR-CAP2702I-A-K9
*spamApTask3: Mar 05 13:38:13.318: apType = 41 apModel: AIR-CAP2702I-A-K9
*spamApTask3: Mar 05 13:38:13.318: 1c:6a:7a:ba:91:e0 Discovery Response sent to 192.168.1.28 port 43295
*spamApTask3: Mar 05 13:38:13.318: 1c:6a:7a:ba:91:e0 Discovery Response sent to 192.168.1.28:43295
*spamApTask3: Mar 05 13:38:13.318: <<<< Start of CAPWAP Packet >>>>
*spamApTask3: Mar 05 13:38:13.318: CAPWAP Control mesg Recd from 192.168.1.28, Port 43295
*spamApTask3: Mar 05 13:38:13.318: HLEN 4, Radio ID 0, WBID 1
*spamApTask3: Mar 05 13:38:13.318: Msg Type : CAPWAP_DISCOVERY_REQUEST
*spamApTask3: Mar 05 13:38:13.318: Msg Length : 165
*spamApTask3: Mar 05 13:38:13.318: Msg SeqNum : 0
*spamApTask3: Mar 05 13:38:13.318:
*spamApTask3: Mar 05 13:38:13.318: Type : CAPWAP_MSGELE_DISCOVERY_TYPE, Length 1
*spamApTask3: Mar 05 13:38:13.318: Discovery Type : CAPWAP_DISCOVERY_TYPE_UNKNOWN
*spamApTask3: Mar 05 13:38:13.318:
*spamApTask3: Mar 05 13:38:13.318: Type : CAPWAP_MSGELE_WTP_BOARD_DATA, Length 62
*spamApTask3: Mar 05 13:38:13.318: Vendor Identifier : 0x00409600
*spamApTask3: Mar 05 13:38:13.318: WTP_SERIAL_NUMBER : AIR-CAP2702I-A-K9
*spamApTask3: Mar 05 13:38:13.318:
*spamApTask3: Mar 05 13:38:13.318: Type : CAPWAP_MSGELE_WTP_DESCRIPTOR, Length 40
*spamApTask3: Mar 05 13:38:13.318: Maximum Radios Supported : 0
*spamApTask3: Mar 05 13:38:13.318: Radios in Use : 0
*spamApTask3: Mar 05 13:38:13.318: Encryption Capabilities : 0x00 0x01
*spamApTask3: Mar 05 13:38:13.318:
*spamApTask3: Mar 05 13:38:13.318: Type : CAPWAP_MSGELE_WTP_FRAME_TUNNEL, Length 1
*spamApTask3: Mar 05 13:38:13.318: WTP Frame Tunnel Mode : NATIVE_FRAME_TUNNEL_MODE
*spamApTask3: Mar 05 13:38:13.318:
*spamApTask3: Mar 05 13:38:13.318: Type : CAPWAP_MSGELE_WTP_MAC_TYPE, Length 1
*spamApTask3: Mar 05 13:38:13.318: WTP Mac Type : SPLIT_MAC
*spamApTask3: Mar 05 13:38:13.318:
*spamApTask3: Mar 05 13:38:13.318: Type : CAPWAP_MSGELE_VENDOR_SPECIFIC_PAYLOAD, Length 10
*spamApTask3: Mar 05 13:38:13.318: Vendor Identifier : 0x00409600
*spamApTask3: Mar 05 13:38:13.318:
IE : UNKNOWN IE 207
*spamApTask3: Mar 05 13:38:13.318: IE Length : 4
*spamApTask3: Mar 05 13:38:13.319: Decode routine not available, Printing Hex Dump
*spamApTask3: Mar 05 13:38:13.319: 00000000: 01 00 00 01 ....
*spamApTask3: Mar 05 13:38:13.319:
*spamApTask3: Mar 05 13:38:13.319: Type : CAPWAP_MSGELE_VENDOR_SPECIFIC_PAYLOAD, Length 22
*spamApTask3: Mar 05 13:38:13.319: Vendor Identifier : 0x00409600
*spamApTask3: Mar 05 13:38:13.319:
IE : RAD_NAME_PAYLOAD
*spamApTask3: Mar 05 13:38:13.319: IE Length : 16
*spamApTask3: Mar 05 13:38:13.319: Rad Name :
*spamApTask3: Mar 05 13:38:13.319: AP1c6a.7aba.91ec
*spamApTask3: Mar 05 13:38:13.319: <<<< End of CAPWAP Packet >>>>
*spamApTask3: Mar 05 13:38:13.319: 1c:6a:7a:ba:91:e0 Discovery Request from 192.168.1.28:43295
*spamApTask3: Mar 05 13:38:13.319: 1c:6a:7a:ba:91:e0 Join Priority Processing status = 0, Incoming Ap's Priority 1, MaxLrads = 5, joined Aps =0
*spamApTask3: Mar 05 13:38:13.319: apModel: AIR-CAP2702I-A-K9
*spamApTask3: Mar 05 13:38:13.319: apType = 41 apModel: AIR-CAP2702I-A-K9
*spamApTask3: Mar 05 13:38:13.319: 1c:6a:7a:ba:91:e0 Discovery Response sent to 192.168.1.28 port 43295
*spamApTask3: Mar 05 13:38:13.319: 1c:6a:7a:ba:91:e0 Discovery Response sent to 192.168.1.28:43295
*spamApTask0: Mar 05 13:38:13.319: 1c:6a:7a:ba:91:ec Received LWAPP DISCOVERY REQUEST to 6c:fa:89:da:ff:00 on port '1'
*spamApTask0: Mar 05 13:38:13.319: Start of Packet
*spamApTask0: Mar 05 13:38:13.319: Ethernet Source MAC (LRAD): 1C:6A:7A:BA:91:ED
*spamApTask0: Mar 05 13:38:13.319: Msg Type :
*spamApTask0: Mar 05 13:38:13.319: DISCOVERY_REQUEST
*spamApTask0: Mar 05 13:38:13.319: Msg Length : 70
*spamApTask0: Mar 05 13:38:13.319: Msg SeqNum : 0
*spamApTask0: Mar 05 13:38:13.319:
IE : UNKNOWN IE 58
*spamApTask0: Mar 05 13:38:13.319: IE Length : 1
*spamApTask0: Mar 05 13:38:13.319: Decode routine not available, Printing Hex Dump
*spamApTask0: Mar 05 13:38:13.319: 00000000: 01 .
*spamApTask0: Mar 05 13:38:13.319:
IE : UNKNOWN IE 50
*spamApTask0: Mar 05 13:38:13.319: IE Length : 46
*spamApTask0: Mar 05 13:38:13.319: Decode routine not available, Printing Hex Dump
*spamApTask0: Mar 05 13:38:13.319: 00000000: 00 00 00 00 00 00 00 00 00 00 00 00 46 54 58 31 ............FTX1
00000010: 38 33 30 53 34 50 39 00 00 00 00 00 00 00 00 00 830S4P9.........
00000020: 00 00 00 00 01 01 00 0
*spamApTask0: Mar 05 13:38:13.319:
IE : RAD_PAYLOAD
*spamApTask0: Mar 05 13:38:13.319: IE Length : 14
*spamApTask0: Mar 05 13:38:13.319: H/W Version : 1
*spamApTask0: Mar 05 13:38:13.319: H/W Release : 0
*spamApTask0: Mar 05 13:38:13.319: H/W Maint : 0
*spamApTask0: Mar 05 13:38:13.319: H/W Build : 0
*spamApTask0: Mar 05 13:38:13.319: S/W Version : 7
*spamApTask0: Mar 05 13:38:13.319: S/W Release : 6
*spamApTask0: Mar 05 13:38:13.319: S/W Maint : 100
*spamApTask0: Mar 05 13:38:13.319: S/W Build : 0
*spamApTask0: Mar 05 13:38:13.319: Boot Version : 15
*spamApTask0: Mar 05 13:38:13.319: Boot Release : 2
*spamApTask0: Mar 05 13:38:13.319: Boot Maint : 4
*spamApTask0: Mar 05 13:38:13.319: Boot Build : 5
*spamApTask0: Mar 05 13:38:13.319: numSlots : 0
*spamApTask0: Mar 05 13:38:13.319: numFilledSlots : 0
*spamApTask0: Mar 05 13:38:13.319: End of Packet
*spamApTask0: Mar 05 13:38:13.319: 1c:6a:7a:ba:91:ec Discarding discovery request in LWAPP from AP supporting CAPWAP
(Cisco Controller) >
From the AP:
*Mar 5 19:48:43.007: LWAPP_CLIENT_EVENT: spamResolveStaticGateway - gateway found
*Mar 5 19:48:43.007: LWAPP_CLIENT_EVENT: spamResolveStaticGateway - gateway found
*Mar 5 19:48:43.007: LWAPP_CLIENT_EVENT: spamSendDiscoveryRequest: sending discovery type 1 to 192.168.1.40
*Mar 5 19:48:53.007: %CAPWAP-3-ERRORLOG: Go join a capwap controller
*Mar 5 19:50:53.000: %CAPWAP-5-DTLSREQSEND: DTLS connection request sent peer_ip: 192.168.1.1 peer_port: 5246
*Mar 5 19:51:22.999: DTLS_CLIENT_ERROR: ../capwap/base_capwap/dtls/base_capwap_dtls_connection_db.c:2176 Max retransmission count reached!
*Mar 5 19:51:52.999: %DTLS-5-SEND_ALERT: Send FATAL : Close notify Alert to 192.168.1.1:5246
*Mar 5 19:51:52.999: %CAPWAP-3-ERRORLOG: Go join a capwap controller
*Mar 5 19:50:53.000: %CAPWAP-5-DTLSREQSEND: DTLS connection request sent peer_ip: 192.168.1.1 peer_port: 5246
*Mar 5 19:51:22.999: DTLS_CLIENT_ERROR: ../capwap/base_capwap/dtls/base_capwap_dtls_connection_db.c:2176 Max retransmission count reached!
*Mar 5 19:51:52.999: %DTLS-5-SEND_ALERT: Send FATAL : Close notify Alert to 192.168.1.1:5246
*Mar 5 19:51:52.999: %CAPWAP-3-ERRORLOG: Go join a capwap controller
*Mar 5 19:50:53.000: %CAPWAP-5-DTLSREQSEND: DTLS connection request sent peer_ip: 192.168.1.1 peer_port: 5246
*Mar 5 19:51:22.999: DTLS_CLIENT_ERROR: ../capwap/base_capwap/dtls/base_capwap_dtls_connection_db.c:2176 Max retransmission count reached!
*Mar 5 19:51:52.999: %DTLS-5-SEND_ALERT: Send FATAL : Close notify Alert to 192.168.1.1:5246
*Mar 5 19:51:52.999: %SYS-3-MGDTIMER: Uninitialized timer, timer stop, timer = 3AFD270. -Process= "CAPWAP CLIENT", ipl= 0, pid= 74
-Traceback= 119AF80z 12A89C8z 12AA11Cz 16F512Cz 17645ECz 16FF088z 172810Cz 17299B4z 1720150z 1720228z 17204ECz 1717E50z 172F6A0z 173075Cz 1324C90z 1309B58z
*Mar 5 19:51:52.999: %LWAPP-3-CLIENTERRORLOG: LWAPP LED Init: incorrect led state 255
*Mar 5 19:51:52.999: %LWAPP-3-CLIENTERRORLOG: Config load from flash failed. Initialising Cfg
*Mar 5 19:51:52.999: %CAPWAP-3-ERRORLOG: Failed to load configuration from flash. Resetting to default config
*Mar 5 19:51:52.999: LWAPP_CLIENT_EVENT: parse_lwapp_config: hostname AP1c6a.7aba.91ec
end
*Mar 5 19:51:53.003: LWAPP_CLIENT_EVENT: lwapp_mesh_enable_dhcp - allow DHCP
*Mar 5 19:51:53.003: LWAPP_CLIENT_EVENT: parse_lwapp_config: cdp run
end
*Mar 5 19:51:53.003: LWAPP_CLIENT_EVENT: parse_lwapp_config: interface GigabitEthernet0
cdp enable
end
*Mar 5 19:51:53.003: LWAPP_CLIENT_EVENT: parse_lwapp_config: interface GigabitEthernet0.1
cdp enable
end
*Mar 5 19:51:53.003: LWAPP_CLIENT_EVENT: parse_lwapp_config: interface GigabitEthernet1
cdp enable
end
*Mar 5 19:51:53.007: %LWAPP-3-CLIENTERRORLOG: Config load from flash failed. Initialising Cfg
*Mar 5 19:51:53.007: LWAPP_CLIENT_EVENT: parse_lwapp_config: line vty 0 15
transport input all
exit
end
"test mesh mode local" is not a supported command on the AP. I tried to see if there was another syntax but couldn't find it.
AP1c6a.7aba.91ec#test mesh mode local
^
% Invalid input detected at '^' marker.
AP1c6a.7aba.91ec#test ?
GigabitEthernet GigabitEthernet IEEE 802.3z
Virtual-Template Virtual Template interface
aaa AAA Authentication, Authorization and Accounting
arp_retry Test ARP Retry
capwap CAPWAP test commands
cef Cisco Express Forwarding test command
cpuaccounting CPU Accounting test commands
cpurmi CPU RMI test commands
crypto Test crypto functions
dpaa DPAA test commands
dtls DTLS test commands
ecc ECC test commands
evtlog Evtlog test commands
ifs IFS TEST code
interfaces Network interfaces
iphc IPHC testing
opssl OPSSL Test
pb Test parameter block file system
persistent Persistent commands
process Create/kill test processes
rib RIB function test
rmi RMI test commands
rtcp Test RTCP SSM
save save load monitor snapshot
spanning-tree Spanning Tree Subsystem
ssm SSM test commands
tar test tar file system
topology Routing Topology test command
transport TACTIC - transport test commands
AP1c6a.7aba.91ec#test
From the AP:
AP1c6a.7aba.91ec#show version
Cisco IOS Software, C2700 Software (AP3G2-RCVK9W8-M), Version 15.2(4)JB5, RELEASE SOFTWARE (fc1)
Technical Support: http://www.cisco.com/techsupport
Copyright (c) 1986-2014 by Cisco Systems, Inc.
Compiled Thu 01-May-14 22:18 by prod_rel_team
ROM: Bootstrap program is C2700 boot loader
BOOTLDR: C2700 Boot Loader (AP3G2-BOOT-M) LoaderVersion 15.2(4)JB5m, RELEASE SOFTWARE (fc2)
AP1c6a.7aba.91ec uptime is 46 minutes
System returned to ROM by power-on
System image file is "flash:/ap3g2-rcvk9w8-mx/ap3g2-rcvk9w8-xx"
Last reload reason:
This product contains cryptographic features and is subject to United
States and local country laws governing import, export, transfer and
use. Delivery of Cisco cryptographic products does not imply
third-party authority to import, export, distribute or use encryption.
Importers, exporters, distributors and users are responsible for
compliance with U.S. and local country laws. By using this product you
agree to comply with applicable laws and regulations. If you are unable
to comply with U.S. and local laws, return this product immediately.
A summary of U.S. laws governing Cisco cryptographic products may be found at:
http://www.cisco.com/wwl/export/crypto/tool/stqrg.html
If you require further assistance please contact us by sending email to
[email protected].
cisco AIR-CAP2702I-A-K9 (PowerPC) processor (revision A0) with 204790K/57344K bytes of memory.
Processor board ID FTX1830S4P9
PowerPC CPU at 800MHz, revision number 0x2151
Last reset from power-on
LWAPP image version 7.6.100.0
1 Gigabit Ethernet interface
32K bytes of flash-simulated non-volatile configuration memory.
Base ethernet MAC Address: 1C:6A:7A:BA:91:EC
Part Number : 73-15824-03
PCA Assembly Number : 000-00000-00
PCA Revision Number :
PCB Serial Number : FOC182876JM
Top Assembly Part Number : 800-41174-01
Top Assembly Serial Number : FTX1830S4P9
Top Revision Number : A0
Product/Model Number : AIR-CAP2702I-A-K9
Configuration register is 0xF
AP1c6a.7aba.91ec#
From the WLC:
(Cisco Controller) >show sysinfo
Manufacturer's Name.............................. Cisco Systems Inc.
Product Name..................................... Cisco Controller
Product Version.................................. 7.6.130.0
Bootloader Version............................... 1.0.20
Field Recovery Image Version..................... 7.6.101.1
Firmware Version................................. PIC 16.0
Build Type....................................... DATA + WPS
System Name...................................... xxxxxxx_lab
System Location..................................
System Contact...................................
System ObjectID.................................. 1.3.6.1.4.1.9.1.1279
IP Address....................................... 192.168.1.40
Last Reset....................................... Software reset
System Up Time................................... 0 days 1 hrs 0 mins 6 secs
System Timezone Location......................... (GMT -6:00) Central Time (US and Canada)
System Stats Realtime Interval................... 5
System Stats Normal Interval..................... 180
--More-- or (q)uit
Configured Country............................... US - United States
Operating Environment............................ Commercial (0 to 40 C)
Internal Temp Alarm Limits....................... 0 to 65 C
Internal Temperature............................. +36 C
External Temperature............................. +41 C
Fan Status....................................... 4700 rpm
State of 802.11b Network......................... Enabled
State of 802.11a Network......................... Enabled
Number of WLANs.................................. 1
Number of Active Clients......................... 0
Burned-in MAC Address............................ 6C:FA:89:DA:FF:00
Maximum number of APs supported.................. 5
(Cisco Controller) >
Similar Messages
-
1242 is not joining controller
hello friends,
i have 1240 series access points which is not joining controller 5500 series..
here is logs at joining time below
AP503d.e56e.e7be#Xmodem file system is available.
flashfs[0]: 7 files, 2 directories
flashfs[0]: 0 orphaned files, 0 orphaned directories
flashfs[0]: Total bytes: 15998976
flashfs[0]: Bytes used: 2649600
flashfs[0]: Bytes available: 13349376
flashfs[0]: flashfs fsck took 25 seconds.
Base ethernet MAC Address: 50:3d:e5:6e:e7:be
Initializing ethernet port 0...
Reset ethernet port 0...
Reset done!
ethernet link up, 100 mbps, full-duplex
Ethernet port 0 initialized: link is up
button is pressed, wait for button to be released...
button pressed for 37 seconds
process_config_recovery: set IP address and config to default 10.0.0.1
process_config_recovery: image recovery
image_recovery: Download default IOS tar image tftp://255.255.255.255/c1240-k9w7-tar.default
examining image...
%Error opening (connection timed out)Loading "flash:/c1240-rcvk9w8-mx/c1240-rcvk9w8-mx"...#############################################################################################################################################
File "flash:/c1240-rcvk9w8-mx/c1240-rcvk9w8-mx" uncompressed and installed, entry point: 0x3000
executing...
Restricted Rights Legend
Use, duplication, or disclosure by the Government is
subject to restrictions as set forth in subparagraph
(c) of the Commercial Computer Software - Restricted
Rights clause at FAR sec. 52.227-19 and subparagraph
(c) (1) (ii) of the Rights in Technical Data and Computer
Software clause at DFARS sec. 252.227-7013.
cisco Systems, Inc.
170 West Tasman Drive
San Jose, California 95134-1706
Cisco IOS Software, C1240 Software (C1240-RCVK9W8-M), Version 12.4(21a)JA2, RELEASE SOFTWARE (fc1)
Technical Support: http://www.cisco.com/techsupport
Copyright (c) 1986-2009 by Cisco Systems, Inc.
Compiled Mon 02-Nov-09 18:40 by prod_rel_team
Proceeding with system init
Proceeding to unmask interrupts
Initializing flashfs...
flashfs[1]: 6 files, 2 directories
flashfs[1]: 0 orphaned files, 0 orphaned directories
flashfs[1]: Total bytes: 15998976
flashfs[1]: Bytes used: 2632192
flashfs[1]: Bytes available: 13366784
flashfs[1]: flashfs fsck took 4 seconds.
flashfs[1]: Initialization complete....done Initializing flashfs.
This product contains cryptographic features and is subject to United
States and local country laws governing import, export, transfer and
use. Delivery of Cisco cryptographic products does not imply
third-party authority to import, export, distribute or use encryption.
Importers, exporters, distributors and users are responsible for
compliance with U.S. and local country laws. By using this product you
agree to comply with applicable laws and regulations. If you are unable
to comply with U.S. and local laws, return this product immediately.
A summary of U.S. laws governing Cisco cryptographic products may be found at:
http://www.cisco.com/wwl/export/crypto/tool/stqrg.html
If you require further assistance please contact us by sending email to
[email protected].
cisco AIR-LAP1242AG-E-K9 (PowerPCElvis) processor (revision A0) with 24566K/8192K bytes of memory.
Processor board ID FCZ150482DL
PowerPCElvis CPU at 262Mhz, revision number 0x0950
Last reset from power-on
LWAPP image version 3.0.51.0
1 FastEthernet interface
32K bytes of flash-simulated non-volatile configuration memory.
Base ethernet MAC Address: 50:3D:E5:6E:E7:BE
Part Number : 73-10256-07
PCA Assembly Number : 800-26918-06
PCA Revision Number : A0
PCB Serial Number : FOC150158MH
Top Assembly Part Number : 800-29152-03
Top Assembly Serial Number : FCZ150482DL
Top Revision Number : A0
Product/Model Number : AIR-LAP1242AG-E-K9
% Please define a domain-name first.
Press RETURN to get started!
*Mar 1 00:00:05.426: %LWAPP-3-CLIENTEVENTLOG: Read and initialized AP event log (contains, 34 messages)
*Mar 1 00:00:07.500: %LINK-3-UPDOWN: Interface FastEthernet0, changed state to up
*Mar 1 00:00:07.526: %SYS-5-RESTART: System restarted --
Cisco IOS Software, C1240 Software (C1240-RCVK9W8-M), Version 12.4(21a)JA2, RELEASE SOFTWARE (fc1)
Technical Support: http://www.cisco.com/techsupport
Copyright (c) 1986-2009 by Cisco Systems, Inc.
Compiled Mon 02-Nov-09 18:40 by prod_rel_team
*Mar 1 00:00:07.601: %CAPWAP-5-CHANGED: CAPWAP changed state to DISCOVERY
*Mar 1 00:00:08.500: %LINEPROTO-5-UPDOWN: Line protocol on Interface FastEthernet0, changed state to down
*Mar 1 00:00:12.979: %LINEPROTO-5-UPDOWN: Line protocol on Interface FastEthernet0, changed state to up
AP503d.e56e.e7be#
*Mar 1 00:00:46.445: %CAPWAP-3-ERRORLOG: Not sending discovery request AP does not have an Ip !!
AP503d.e56e.e7be#
AP503d.e56e.e7be#
AP503d.e56e.e7be#sh ver
Cisco IOS Software, C1240 Software (C1240-RCVK9W8-M), Version 12.4(21a)JA2, RELEASE SOFTWARE (fc1)
Technical Support: http://www.cisco.com/techsupport
Copyright (c) 1986-2009 by Cisco Systems, Inc.
Compiled Mon 02-Nov-09 18:40 by prod_rel_team
ROM: Bootstrap program is C1240 boot loader
BOOTLDR: C1240 Boot Loader (C1240-BOOT-M) Version 12.4(13d)JA, RELEASE SOFTWARE (fc2)
AP503d.e56e.e7be uptime is 0 minutes
System returned to ROM by power-on
System image file is "flash:/c1240-rcvk9w8-mx/c1240-rcvk9w8-mx"
This product contains cryptographic features and is subject to United
States and local country laws governing import, export, transfer and
use. Delivery of Cisco cryptographic products does not imply
third-party authority to import, export, distribute or use encryption.
Importers, exporters, distributors and users are responsible for
compliance with U.S. and local country laws. By using this product you
agree to comply with applicable laws and regulations. If you are unable
to comply with U.S. and local laws, return this product immediately.
A summary of U.S. laws governing Cisco cryptographic products may be found at:
http://www.cisco.com/wwl/export/crypto/tool/stqrg.html
If you require further assistance please contact us by sending email to
[email protected].
cisco AIR-LAP1242AG-E-K9 (PowerPCElvis) processor (revision A0) with 24566K/8192K bytes of memory.
Processor board ID FCZ150482DL
PowerPCElvis CPU at 262Mhz, revision number 0x0950
Last reset from power-on
LWAPP image version 3.0.51.0
1 FastEthernet interface
32K bytes of flash-simulated non-volatile configuration memory.
Base ethernet MAC Address: 50:3D:E5:6E:E7:BE
Part Number : 73-10256-07
PCA Assembly Number : 800-26918-06
PCA Revision Number : A0
PCB Serial Number : FOC150158MH
Top Assembly Part Number : 800-29152-03
Top Assembly Serial Number : FCZ150482DL
--More--
*Mar 1 00:00:56.445: %CAPWAP-3-ERRORLOG: Not sending discovery request AP does not haveTop Revision Number : A0
Product/Model Number : AIR-LAP1242AG-E-K9
Configuration register is 0xF
AP503d.e56e.e7be#
*Mar 1 00:01:06.445: %CAPWAP-3-ERRORLOG: Not sending discovery request AP does not have an Ip !!
any advice please??
thanksIt sounds like you are still working out IP connectivity, but I also noticed your AP is not for US regulatory domain.
Can you confirm that your WLC is ready to accept an AP with country code -E?
Your AP model: AIR-LAP1242AG-E-K9
From the WLC CLI
>show country
If you are in US, you should only have -A available. If this AP is intended to be used the US, then you will need to acquire an AP with the correct country code, as -E would not be supported in the US -A regulatory domain and should not be used. Perhaps this is for another location, so you may need to add the applicable regulatory domain support.
This link provides the list of the respective country codes and compatbility/etc.
http://www.cisco.com/en/US/prod/collateral/wireless/ps5679/ps5861/product_data_sheet0900aecd80537b6a_ps6087_Products_Data_Sheet.html -
i am trying to troubleshoot a 2125 WLC alongside a 1252 access point. The access point is not joining and the y both
have the same software image. See logs below:
(Cisco Controller) >show sysinfo
Manufacturer's Name.............................. Cisco Systems Inc.
Product Name..................................... Cisco Controller
Product Version.................................. 5.2.193.0
RTOS Version..................................... 5.2.193.0
Bootloader Version............................... 4.0.191.0
Emergency Image Version.......................... 6.0.199.4
Build Type....................................... DATA + WPS
System Name...................................... Cisco_f4:f7:c0
System Location..................................
System Contact...................................
System ObjectID.................................. 1.3.6.1.4.1.9.1.828
IP Address....................................... 192.168.1.5
System Up Time................................... 6 days 2 hrs 42 mins 39 secs
System Timezone Location.........................
Current Boot License Level.......................
Next Boot License Level..........................
Configured Country............................... SI - Slovenia
Operating Environment............................ Commercial (0 to 40 C)
Internal Temp Alarm Limits....................... 0 to 65 C
--More-- or (q)uit
Internal Temperature............................. +49 C
State of 802.11b Network......................... Enabled
State of 802.11a Network......................... Enabled
Number of WLANs.................................. 3
3rd Party Access Point Support................... Disabled
Number of Active Clients......................... 0
Burned-in MAC Address............................ C8:4C:75:F4:F7:C0
(Cisco Controller) >show network summary
RF-Network Name............................. law school
Web Mode.................................... Disable
Secure Web Mode............................. Enable
Secure Web Mode Cipher-Option High.......... Disable
Secure Web Mode Cipher-Option SSLv2......... Enable
Secure Shell (ssh).......................... Enable
Telnet...................................... Disable
Ethernet Multicast Mode..................... Disable
Ethernet Broadcast Mode..................... Disable
AP Multicast Mode........................... Multicast Address : 0.0.0.0
IGMP snooping............................... Disabled
IGMP timeout................................ 60 seconds
User Idle Timeout........................... 300 seconds
ARP Idle Timeout............................ 300 seconds
Cisco AP Default Master..................... Disable
AP Join Priority............................ Disable
Mgmt Via Wireless Interface................. Enable
Mgmt Via Dynamic Interface.................. Enable
Bridge MAC filter Config.................... Enable
Bridge Security Mode........................ EAP
Mesh Full Sector DFS........................ Enable
Kindly advice what is missing?
many thanksConsole into the AP and post the output to the following commands:
1. sh version;
2. sh ip interface brief -
Reset 1510 AP not joining controller
Hi
I have a 3750 Controller with 1510 access points. I have 1 access point that will not join. I think it was configured as a remote with a fixed IP address but I don't know what that address is, and I think that it is not the right subnet. I think I need to re-prime the AP with new settings.
Unfortunately I suspect that it because it has a set IP address it will now not try to get a DHCP address and thus I cannot prime it using that method. Is there another way to reset the IP address on these units?
Many Thanks
LPHi Laurie,
We do not run 1510's so I can't verify this, but I did come across this info;
Misconfigured Access Point IP address
IP address misconfiguration can occur when you are re-addressing a segment of your mesh network and you start at the mesh access point connected to the wired network (RAP). To avoid this problem, always start the IP addressing changes from the farthest access point and work your way back to the root access point. This problem might also happen if you move equipment such as uninstalling an mesh access point and then redeploying with a different IP subnet in another physical location on the mesh network.
Another option to fix this misconfigured IP address is to physically take a controller in Layer 2 mode with a root access point to the location of the misconfigured mesh access point. Set the bridge group name for the root access point to match the misconfigured access point. Add the access point's MAC address to the controller's filter list and enable Zero Touch Configuration. When the misconfigured access point appears in the controller's Summary page, configure the access point with an IP address.
From this doc;
http://www.cisco.com/en/US/products/ps6548/products_quick_start09186a00806b5d00.html#wp39368
Hope this helps!
Rob -
Wireless AP not joining Controller
Hi,
I am facing an issue with my AP not joining the controller.
Following is the error log
Mar 1 00:01:11.923: %CAPWAP-3-ERRORLOG: Could Not resolve CISCO-CAPWAP-CONTROLLER
*Mar 1 00:01:21.923: %CAPWAP-3-ERRORLOG: Go join a capwap controller
*Apr 3 08:10:04.000: %CAPWAP-5-DTLSREQSEND: DTLS connection request sent peer_ip: 10.146.47.150 peer_port: 5246
*Apr 3 08:10:26.775: %CDP_PD-4-POWER_OK: Full power - NEGOTIATED inline power source
*Apr 3 08:10:33.999: DTLS_CLIENT_ERROR: ../capwap/base_capwap/dtls/base_capwap_dtls_connection_db.c:2051 Max retransmission count reached!
*Apr 3 08:11:03.999: %DTLS-5-SEND_ALERT: Send FATAL : Close notify Alert to 10.146.47.150:5246
*Apr 3 08:11:03.999: %CAPWAP-3-ERRORLOG: Go join a capwap controller
*Apr 3 08:10:04.000: %CAPWAP-5-DTLSREQSEND: DTLS connection request sent peer_ip: 10.146.47.150 peer_port: 5246Hi Guys,
Thanks for your inputs.
I investigated the issue suspecting a problem with the communication between the WLC and the APs. Actually the WLC is connected to 2 6506 chassis with the 1st chassis as the root.
I discovered a minor error on the module in the 1st chassis. When i connected to the 2nd chassis. The AP was able to join the controller. Outputs for the faulty module as below:
Looks like I will need to RMA the module.
Router#sh module
Mod Ports Card Type Model Serial No.
1 48 CEF720 48 port 10/100/1000mb Ethernet WS-X6748-GE-TX SAL1743F20V
2 16 CEF720 16 port 10GE WS-X6716-10GE SAL1746G9RS
3 16 CEF720 16 port 10GE WS-X6716-10GE SAL1746G9QR
5 5 Supervisor Engine 720 10GE (Active) VS-S720-10G SAL1746GC1G
Mod MAC addresses Hw Fw Sw Status
1 7c69.f690.8908 to 7c69.f690.8937 4.3 12.2(18r)S1 12.2(33)SXJ6 Ok
2 7c69.f690.badc to 7c69.f690.baeb 2.1 12.2(18r)S1 12.2(33)SXJ6 Ok
3 e4d3.f1a4.39f8 to e4d3.f1a4.3a07 2.1 12.2(18r)S1 12.2(33)SXJ6 Ok
5 5057.a8e3.394a to 5057.a8e3.3951 4.1 8.5(4) 12.2(33)SXJ6 Ok
Mod Sub-Module Model Serial Hw Status
1 Centralized Forwarding Card WS-F6700-CFC SAL1746GAAX 4.1 Ok
2 Distributed Forwarding Card WS-F6700-DFC3C SAL1746G6T1 1.6 Ok
3 Distributed Forwarding Card WS-F6700-DFC3C SAL1746G844 1.6 Ok
5 Policy Feature Card 3 VS-F6K-PFC3C SAL1746GBJK 1.2 Ok
5 MSFC3 Daughterboard VS-F6K-MSFC3 SAL1746GAGT 5.1 Ok
Mod Online Diag Status
1 Minor Error
2 Pass
3 Pass
5 Pass
Router#sh diagnostic result module 1
Current bootup diagnostic level: minimal
Module 1: CEF720 48 port 10/100/1000mb Ethernet SerialNo : SAL1743F20V
Overall Diagnostic Result for Module 1 : MINOR ERROR
Diagnostic level at card bootup: minimal
Test results: (. = Pass, F = Fail, U = Untested)
1) TestLoopback:
Port 1 2 3 4 5 6 7 8 9 10 11 12 13 14 15 16 17 18 19 20 21 22 23 24
Port 25 26 27 28 29 30 31 32 33 34 35 36 37 38 39 40 41 42 43 44 45 46 47 48
2) TestTxPathMonitoring ------------> .
3) TestSynchedFabChannel -----------> .
4) TestL3VlanMet -------------------> F
5) TestIngressSpan -----------------> .
6) TestEgressSpan ------------------> .
7) TestAsicMemory ------------------> U
8) TestEobcStressPing --------------> U
9) TestFirmwareDiagStatus ----------> .
10) TestAsicSync --------------------> .
11) TestUnusedPortLoopback:
Port 1 2 3 4 5 6 7 8 9 10 11 12 13 14 15 16 17 18 19 20 21 22 23 24
U U U U U U U U U U U . U U U U U U U U U U U .
Port 25 26 27 28 29 30 31 32 33 34 35 36 37 38 39 40 41 42 43 44 45 46 47 48
U U U U U U U U U U U . U U U U U U U U U U U .
12) TestOBFL ------------------------> .
13) TestErrorCounterMonitor ---------> .
14) TestPortTxMonitoring:
Port 1 2 3 4 5 6 7 8 9 10 11 12 13 14 15 16 17 18 19 20 21 22 23 24
U U U U U U U U U U U U U U U U U U U U U U U U
Port 25 26 27 28 29 30 31 32 33 34 35 36 37 38 39 40 41 42 43 44 45 46 47 48
U U U U U U U U U U U U U U U U U U U U U U U U
15) TestLtlFpoeMemoryConsistency ----> .
16) TestRwEngineOverSubscription ----> U
Router#sh diagnostic result module 1 detail
Current bootup diagnostic level: minimal
Module 1: CEF720 48 port 10/100/1000mb Ethernet SerialNo : SAL1743F20V
Overall Diagnostic Result for Module 1 : MINOR ERROR
Diagnostic level at card bootup: minimal
Test results: (. = Pass, F = Fail, U = Untested)
1) TestLoopback:
Port 1 2 3 4 5 6 7 8 9 10 11 12 13 14 15 16 17 18 19 20 21 22 23 24
Port 25 26 27 28 29 30 31 32 33 34 35 36 37 38 39 40 41 42 43 44 45 46 47 48
Error code ------------------> 0 (DIAG_SUCCESS)
Total run count -------------> 1
Last test testing type ------> Bootup
Last test execution time ----> Apr 01 2014 10:55:39
First test failure time -----> n/a
Last test failure time ------> n/a
Last test pass time ---------> Apr 01 2014 10:55:39
Total failure count ---------> 0
Consecutive failure count ---> 0
2) TestTxPathMonitoring ------------> .
Error code ------------------> 0 (DIAG_SUCCESS)
Total run count -------------> 40
Last test testing type ------> Health Monitoring
Last test execution time ----> Apr 01 2014 10:57:30
First test failure time -----> n/a
Last test failure time ------> n/a
Last test pass time ---------> Apr 01 2014 10:57:30
Total failure count ---------> 0
Consecutive failure count ---> 0
3) TestSynchedFabChannel -----------> .
Error code ------------------> 0 (DIAG_SUCCESS)
Total run count -------------> 39
Last test testing type ------> Health Monitoring
Last test execution time ----> Apr 01 2014 10:57:30
First test failure time -----> n/a
Last test failure time ------> n/a
Last test pass time ---------> Apr 01 2014 10:57:30
Total failure count ---------> 0
Consecutive failure count ---> 0
4) TestL3VlanMet -------------------> F
Error code ------------------> 54 (DIAG_CHECK_UDP_PAK_ERROR)
Total run count -------------> 1
Last test testing type ------> Bootup
Last test execution time ----> Apr 01 2014 10:55:53
First test failure time -----> Apr 01 2014 10:55:53
Last test failure time ------> Apr 01 2014 10:55:53
Last test pass time ---------> n/a
Total failure count ---------> 1
Consecutive failure count ---> 1
5) TestIngressSpan -----------------> .
Error code ------------------> 0 (DIAG_SUCCESS)
Total run count -------------> 1
Last test testing type ------> Bootup
Last test execution time ----> Apr 01 2014 10:56:05
First test failure time -----> n/a
Last test failure time ------> n/a
Last test pass time ---------> Apr 01 2014 10:56:05
Total failure count ---------> 0
Consecutive failure count ---> 0
6) TestEgressSpan ------------------> .
Error code ------------------> 0 (DIAG_SUCCESS)
Total run count -------------> 1
Last test testing type ------> Bootup
Last test execution time ----> Apr 01 2014 10:56:05
First test failure time -----> n/a
Last test failure time ------> n/a
Last test pass time ---------> Apr 01 2014 10:56:05
Total failure count ---------> 0
Consecutive failure count ---> 0
7) TestAsicMemory ------------------> U
Error code ------------------> 3 (DIAG_SKIPPED)
Total run count -------------> 0
Last test testing type ------> n/a
Last test execution time ----> n/a
First test failure time -----> n/a
Last test failure time ------> n/a
Last test pass time ---------> n/a
Total failure count ---------> 0
Consecutive failure count ---> 0
8) TestEobcStressPing --------------> U
Error code ------------------> 3 (DIAG_SKIPPED)
Total run count -------------> 0
Last test testing type ------> n/a
Last test execution time ----> n/a
First test failure time -----> n/a
Last test failure time ------> n/a
Last test pass time ---------> n/a
Total failure count ---------> 0
Consecutive failure count ---> 0
9) TestFirmwareDiagStatus ----------> .
Error code ------------------> 0 (DIAG_SUCCESS)
Total run count -------------> 1
Last test testing type ------> Bootup
Last test execution time ----> Apr 01 2014 10:56:05
First test failure time -----> n/a
Last test failure time ------> n/a
Last test pass time ---------> Apr 01 2014 10:56:05
Total failure count ---------> 0
Consecutive failure count ---> 0
10) TestAsicSync --------------------> .
Error code ------------------> 0 (DIAG_SUCCESS)
Total run count -------------> 5
Last test testing type ------> Health Monitoring
Last test execution time ----> Apr 01 2014 10:57:21
First test failure time -----> n/a
Last test failure time ------> n/a
Last test pass time ---------> Apr 01 2014 10:57:21
Total failure count ---------> 0
Consecutive failure count ---> 0
11) TestUnusedPortLoopback:
Port 1 2 3 4 5 6 7 8 9 10 11 12 13 14 15 16 17 18 19 20 21 22 23 24
U U U U U U U U U U U . U U U U U U U U U U U .
Port 25 26 27 28 29 30 31 32 33 34 35 36 37 38 39 40 41 42 43 44 45 46 47 48
U U U U U U U U U U U . U U U U U U U U U U U .
Error code ------------------> 0 (DIAG_SUCCESS)
Total run count -------------> 1
Last test testing type ------> Health Monitoring
Last test execution time ----> Apr 01 2014 10:57:06
First test failure time -----> n/a
Last test failure time ------> n/a
Last test pass time ---------> Apr 01 2014 10:57:06
Total failure count ---------> 0
Consecutive failure count ---> 0
12) TestOBFL ------------------------> .
Error code ------------------> 0 (DIAG_SUCCESS)
Total run count -------------> 1
Last test testing type ------> Bootup
Last test execution time ----> Apr 01 2014 10:56:05
First test failure time -----> n/a
Last test failure time ------> n/a
Last test pass time ---------> Apr 01 2014 10:56:05
Total failure count ---------> 0
Consecutive failure count ---> 0
13) TestErrorCounterMonitor ---------> .
Error code ------------------> 0 (DIAG_SUCCESS)
Total run count -------------> 2
Last test testing type ------> Health Monitoring
Last test execution time ----> Apr 01 2014 10:57:06
First test failure time -----> n/a
Last test failure time ------> n/a
Last test pass time ---------> Apr 01 2014 10:57:06
Total failure count ---------> 0
Consecutive failure count ---> 0
Error Records ---------------> n/a
14) TestPortTxMonitoring:
Port 1 2 3 4 5 6 7 8 9 10 11 12 13 14 15 16 17 18 19 20 21 22 23 24
U U U U U U U U U U U U U U U U U U U U U U U U
Port 25 26 27 28 29 30 31 32 33 34 35 36 37 38 39 40 41 42 43 44 45 46 47 48
U U U U U U U U U U U U U U U U U U U U U U U U
Error code ------------------> 0 (DIAG_SUCCESS)
Total run count -------------> 1
Last test testing type ------> Health Monitoring
Last test execution time ----> Apr 01 2014 10:57:21
First test failure time -----> n/a
Last test failure time ------> n/a
Last test pass time ---------> Apr 01 2014 10:57:21
Total failure count ---------> 0
Consecutive failure count ---> 0
15) TestLtlFpoeMemoryConsistency ----> .
Error code ------------------> 0 (DIAG_SUCCESS)
Total run count -------------> 5
Last test testing type ------> Health Monitoring
Last test execution time ----> Apr 01 2014 10:57:21
First test failure time -----> n/a
Last test failure time ------> n/a
Last test pass time ---------> Apr 01 2014 10:57:21
Total failure count ---------> 0
Consecutive failure count ---> 0
16) TestRwEngineOverSubscription ----> U
Error code ------------------> 3 (DIAG_SKIPPED)
Total run count -------------> 0
Last test testing type ------> n/a
Last test execution time ----> n/a
First test failure time -----> n/a
Last test failure time ------> n/a
Last test pass time ---------> n/a
Total failure count ---------> 0
Consecutive failure count ---> 0
Router#sh diagnostic result module 1 failure
Current bootup diagnostic level: minimal
Module 1: CEF720 48 port 10/100/1000mb Ethernet SerialNo : SAL1743F20V
Overall Diagnostic Result for Module 1 : MINOR ERROR
Diagnostic level at card bootup: minimal
Test results: (. = Pass, F = Fail, U = Untested)
4) TestL3VlanMet -------------------> F -
LWAP not joining controller, but has downloaded software
Hi All,
I have four APs that when I powered on individually, they went into the downloading state and rebooted, now have the mac address APxxxx.xxxx.xxxx.cisco.com and can see this on my switch and cdp is working, but has not joined the controller?
I know that DHCP is set correctly as I have another AP on the switch/VLAN that is working?
Any ideas?
Many thx indeed,
KenTo answer your specific question, there's no need to clear anything on the WLC. The access points should simply connect.
Did you upgrade these access points, and could this be a certificate issue? If they are upgraded 1100s or 1200s, you may need to add the SSCs generated during the upgrade process into the controller. This can be done under the Security tab.
If that's not the issue, I would try to connect the access points more directly by placing them on the management subnet. This will hopefully tell you whether there's a problem with your discovery method.
Have you looked at the access points to see their status according to their LEDs? Are they still seeking a controller? Is it possible that they've found a different controller somewhere else on the network? -
Mesh AP 1524SB Not Joining Controller
Hello,
I'm just getting started here and have run into some problems.
I have a WLC 5508 running 7.0.116.0 and 1524SB access points.
I have a 3750 switch sitting between them hosting the DHCP.
The switch is using VLAN 1 and the management interface of the WLC is untagged.
The problem is that my APs will not join the controller. I don't even think they are getting an IP address.
When I console into the AP it seems to me that the boot process is interupted and the AP reboots.
I get this message:
*Mar 1 00:00:34.375: %SYS-5-RELOAD: Reload requested by Adj Process. Reload Reason: Mesh Reboots AP ....
*Mar 1 00:00:34.375: %LWAPP-5-CHANGED: CAPWAP changed state to DOWNWriting out the event log to nvram...
And then it reboots. I have attached the entire boot sequence.
Could someone help me out please?
Thanks,
Justin
PS if needed here is the dhcp config:
ip dhcp pool dhcp
network 10.0.0.0 255.255.255.0
default-router 10.0.0.254
option 60 ascii "Cisco AP c1520"
option 43 ip 10.0.0.1
where 10.0.0.1 is the ip of the management interface.Assuming 10.0.0.1 is the controller's management IP address. For 1524SB Mesh AP, you can't use format of "option 43 ip 10.0.0.1", change it to "option 43 hex f1040a000001" on the 3750 switch and try again.
-
1140 AP not joining controller
I have 3 AP's setup on my network and each port is configured the same exact way on the switches. One AP joined the controller fine but the other two are not joning it. They get the IP address but that is about it. When I go and check for the statistics on the WLC it tells me that they are not joined. Here is what the DEBUG shows:
*spamApTask5: Apr 18 18:13:01.198: c4:71:fe:8f:da:dc CAPWAP Control Msg Received from 10.230.129.113:60844
*spamApTask5: Apr 18 18:13:01.198: c4:71:fe:8f:da:dc packet received of length 97 from 10.230.129.113:60844
*spamApTask5: Apr 18 18:13:01.198: c4:71:fe:8f:da:dc Msg Type = 1 Capwap state = 0
*spamApTask5: Apr 18 18:13:01.198: c4:71:fe:8f:da:dc Discovery Request from 10.230.129.113:60844
*spamApTask5: Apr 18 18:13:01.198: c4:71:fe:8f:da:dc msgEleLength = 1 msgEleType = 20
*spamApTask5: Apr 18 18:13:01.198: c4:71:fe:8f:da:dc Total msgEleLen = 68
*spamApTask5: Apr 18 18:13:01.198: c4:71:fe:8f:da:dc msgEleLength = 40 msgEleType = 39
*spamApTask5: Apr 18 18:13:01.198: c4:71:fe:8f:da:dc Total msgEleLen = 24
*spamApTask5: Apr 18 18:13:01.198: c4:71:fe:8f:da:dc msgEleLength = 1 msgEleType = 41
*spamApTask5: Apr 18 18:13:01.198: c4:71:fe:8f:da:dc Total msgEleLen = 19
*spamApTask5: Apr 18 18:13:01.198: c4:71:fe:8f:da:dc msgEleLength = 1 msgEleType = 44
*spamApTask5: Apr 18 18:13:01.198: c4:71:fe:8f:da:dc Total msgEleLen = 14
*spamApTask5: Apr 18 18:13:01.199: c4:71:fe:8f:da:dc msgEleLength = 10 msgEleType = 37
*spamApTask5: Apr 18 18:13:01.199: c4:71:fe:8f:da:dc Vendor specific payload from AP C4:71:FE:8F:DA:DC validated
*spamApTask5: Apr 18 18:13:01.199: c4:71:fe:8f:da:dc Total msgEleLen = 0
*spamApTask5: Apr 18 18:13:01.199: c4:71:fe:8f:da:dc Join Priority Processing status = 0, Incoming Ap's Priority 1, MaxLrads = 12, joined Aps =1
*spamApTask5: Apr 18 18:13:01.199: c4:71:fe:8f:da:dc 1. 1 0
*spamApTask5: Apr 18 18:13:01.199: c4:71:fe:8f:da:dc 2. 232 3
*spamApTask5: Apr 18 18:13:01.199: c4:71:fe:8f:da:dc 3. 1 0
*spamApTask5: Apr 18 18:13:01.199: c4:71:fe:8f:da:dc 4. 12 0
*spamApTask5: Apr 18 18:13:01.199: c4:71:fe:8f:da:dc Discovery resp: AC Descriptor message element len = 40
*spamApTask5: Apr 18 18:13:01.199: c4:71:fe:8f:da:dc acName = WLCNAME
*spamApTask5: Apr 18 18:13:01.199: c4:71:fe:8f:da:dc Discovery resp:AC Name message element length = 56
*spamApTask5: Apr 18 18:13:01.199: c4:71:fe:8f:da:dc Discovery resp: WTP Radio Information msg length = 65
*spamApTask5: Apr 18 18:13:01.199: c4:71:fe:8f:da:dc Discovery resp: CAPWAP Control IPV4 Address len = 85
*spamApTask5: Apr 18 18:13:01.199: c4:71:fe:8f:da:dc Discovery resp: CAPWAP Control IPV6 Address len = 107
*spamApTask5: Apr 18 18:13:01.199: c4:71:fe:8f:da:dc Discovery resp: Mwar type payload len = 118
*spamApTask5: Apr 18 18:13:01.199: c4:71:fe:8f:da:dc Discovery resp: Time sync payload len = 133
*spamApTask5: Apr 18 18:13:01.199: c4:71:fe:8f:da:dc Discovery Response sent to 10.230.129.113:60844
*spamApTask5: Apr 18 18:13:01.199: c4:71:fe:8f:da:dc WTP already released
Note: I have one "management interface" configured on 10.230.129.xxx network" Then I created two "AP Manager interfaces on the 10.230.129.xxx network and enabled dynamic AP Management on them".Ok, right, thats because whenever you type ANY number it TAGs the packets with that vlan id. 0 leaves the traffic untagged.
So even if it that IP belongs to vlan 10, if the port is as native (untagged) then on the WLC side should be 0
Thats how it was designed. -
Hi guys,
I am in the process of configuring a WLC and got stuck due to APs are not joining the WLC.
I have configure DHCP server on the Gateway router and the WLC management interface is pointing to the Gateway as DHCP Server.
I have multiple Dynamic interfaces configured on the WLC and Interface group has been configured and mapped to Management Interface.
For each WLAN, a separate DHCP pool has been created on the router.
LAG has been configured and working fine. Connectivity works fine in the network and I can ping all devices and vlans from WLC.
Now, the APs are not joining the WLC. The error I am getting
" 44:03:a7:f1:b4:40 Received a Discovery Request from 44:03:A7:F1:B4:40 via IP broadcast address but the source IP address (10.xx.xx.xx) is not in any of the configured subnets. Dropping it "
Some one help me troubleshooting this issue with DHCP IP Assignment.
Thanks,
CJIf you are using Broadcast method to discover WLC to AP then you need to ensure following is correctly configured.
1. Unders the switch SVI defined for AP-management (10.38.11.x) you have to configure "ip helper-address "
2. In switch global config "ip forward-protocol udp 5246"
Refer this for more detail
http://mrncciew.com/2013/05/04/wlc-discovery-via-broadcast/
There are other methods available as well (static, DNS, DHCP option 43) for the WLC discovery purpose. To verify there is no configuration issues at WLC end, you can simply configure the WLC details on AP statically & check wether AP get register to WLC. To do this you can enter following CLI commands on AP console priviledge mode.
debug capwap console cli
capwap ap ip address 10.38.11.x 255.255.255.x
capwap ap ip default-gateway 10.38.11.y
capwap ap controller ip address
In this way your AP should get registered to WLC (if no config issue at WLC end). Refer this for more detail
http://mrncciew.com/2013/03/17/ap-registration/
If you have so many APs, then as Steve pointed configuring DHCP-Option 43 would be a good option
Regards
Rasika
**** Pls rate all useful responses **** -
hi All,
I have a scenario where my 2602E is not joining a controller in US. AP is in Netherlands.
AP: AIR-CAP2602E-E-K9
Logs on WLC 5508:
*spamApTask4: Jan 29 10:26:37.398: 18:9c:5d:9b:4d:00 Bridge AP can not join MultiCountry Controller: Bridge mode AP 10.130.90.11:63313 cannot be supported on Multi Country Controll
*spamApTask4: Jan 29 10:26:37.406: 18:9c:5d:9b:4d:00 State machine handler: Failed to process msg type = 3 state = 0 from 10.130.90.11:63313
is there a way i can change the bridge mode from this AP to normal or Local so that it can be useD?
Any help will be great.
thanks
Roycecheck the following.
-
Flexconnect AP not joining Controller
Hi Community ,
I have some flexconnect APs in remote side . But they are not able to join controller 5508 (7.6) and flexconnect is also showing down in PI.
Any reason ??Hi Adam ,
Thanks for your reply .
Scenario is that we have 2 controllers in HQ . Controllers running IOS code 7.6 . APs are 1242 LAP . They were working fine just one week ago . But now I can see them they are not in the controller , though up . When I checked in PI , Flexconnect status showing down . Hope this will help . -
APs not joining controller errors
I keep getting errors on different APs not joining controllers:
Jan 5 15:54:40.097: %CAPWAP-3-ERRORLOG: Go join a capwap controller
*Jan 5 15:54:40.000: %CAPWAP-5-DTLSREQSEND: DTLS connection request sent peer_ip: 10.x.x.x peer_port: 5246
*Jan 5 15:54:40.001: %CAPWAP-5-CHANGED: CAPWAP changed state to
*Jan 5 15:54:41.778: %CAPWAP-5-DTLSREQSUCC: DTLS connection created sucessfully peer_ip: 10.x.x.x peer_port: 5246
*Jan 5 15:54:41.780: %CAPWAP-5-SENDJOIN: sending Join Request to 10.x.x.x
*Jan 5 15:54:41.780: %CAPWAP-5-CHANGED: CAPWAP changed state to JOIN
*Jan 5 15:54:41.787: %DTLS-5-ALERT: Received WARNING : Close notify alert from 10.x.x.x
*Jan 5 15:54:41.788: %DTLS-5-PEER_DISCONNECT: Peer 10.x.x.x has closed connection.
*Jan 5 15:54:41.788: %DTLS-5-SEND_ALERT: Send WARNING : Close notify Alert to 10.x.x.x :5246.
Any ideas? I'm not sure why the peer is disconnecting the connection. The controller that is linked to It happens on 1242 and 1231 APs mostly. I've had it happen on a 1142 and 1252 once, but after a reboot it joined fine.
I'm running 6.0.188.0 on 6 WISMs. The ap-manager that these APs keep trying to join only has 5 APs on it.Can you get a sniffer trace of the port-channel to one of the WiSM, and if possible, the console of the AP? Also, check the MAC address of the AP(s) that are not joining to see if they start with something other than 00:, you may also want to check the MAC of the gw for those AP for the same thing.
The defect I'm thinking of is CSCte01087 -
Cisco 7925 not joining WLAN Network
hi
I have one 7925G-E phone, 1142-E LAP & WLC 5508 & CME 71. in a 3900 router. I am trying to join the phone with CME but the
phone is not joining the WLAN network.
showing error msg connection failed, i have tried with WEP, Open, Open+WEP option on the phone and WLC but still facing problem,.
Thanks
Saurav
I have tried with WPA-PSK and tried the notebook to join it is joining but the Phone is not joiining getting the same error.
connection failed.
*May 02 15:37:52.629: %LWAPP-3-WLAN_ERR2: spam_lrad.c:20904 Unable to find WLAN 7 to be deleted; AP 00:3a:98:0d:e9:90
*May 02 15:37:52.629: %LWAPP-3-WLAN_ERR2: spam_lrad.c:21261 Unable to find WLAN 7 to be deleted; AP 00:3a:98:0d:e9:90
*May 02 15:37:52.628: %LWAPP-3-WLAN_ERR2: spam_lrad.c:20904 Unable to find WLAN 7 to be deleted; AP 00:3a:98:0d:e8:b0
*May 02 15:37:52.628: %LWAPP-3-WLAN_ERR2: spam_lrad.c:21261 Unable to find WLAN 7 to be deleted; AP 00:3a:98:0d:e8:b0
*May 02 15:37:52.628: %LWAPP-3-WLAN_ERR2: spam_lrad.c:20904 Unable to find WLAN 7 to be deleted; AP 00:3a:98:0d:e5:c0
*May 02 15:37:52.628: %LWAPP-3-WLAN_ERR2: spam_lrad.c:21261 Unable to find WLAN 7 to be deleted; AP 00:3a:98:0d:e5:c0
*May 02 15:37:52.626: %LWAPP-3-WLAN_ERR2: spam_lrad.c:20904 Unable to find WLAN 7 to be deleted; AP 00:3a:98:0d:e2:50
*May 02 15:37:52.626: %LWAPP-3-WLAN_ERR2: spam_lrad.c:21261 Unable to find WLAN 7 to be deleted; AP 00:3a:98:0d:e2:50
*May 02 15:37:52.625: %LWAPP-3-WLAN_ERR2: spam_lrad.c:20904 Unable to find WLAN 7 to be deleted; AP 00:3a:98:08:2f:70
*May 02 15:37:52.625: %LWAPP-3-WLAN_ERR2: spam_lrad.c:21261 Unable to find WLAN 7 to be deleted; AP 00:3a:98:08:2f:70
*May 02 15:37:52.623: %LWAPP-3-WLAN_ERR2: spam_lrad.c:20904 Unable to find WLAN 7 to be deleted; AP 00:3a:98:08:2f:60
*May 02 15:37:52.623: %LWAPP-3-WLAN_ERR2: spam_lrad.c:21261 Unable to find WLAN 7 to be deleted; AP 00:3a:98:08:2f:60
*May 02 15:27:36.864: %LWAPP-3-WLAN_ERR2: spam_lrad.c:20904 Unable to find WLAN 7 to be deleted; AP 00:3a:98:0d:e9:90
*May 02 15:27:36.864: %LWAPP-3-WLAN_ERR2: spam_lrad.c:21261 Unable to find WLAN 7 to be deleted; AP 00:3a:98:0d:e9:90
*May 02 15:27:36.863: %LWAPP-3-WLAN_ERR2: spam_lrad.c:20904 Unable to find WLAN 7 to be deleted; AP 00:3a:98:0d:e8:b0
*May 02 15:27:36.863: %LWAPP-3-WLAN_ERR2: spam_lrad.c:21261 Unable to find WLAN 7 to be deleted; AP 00:3a:98:0d:e8:b0
*May 02 15:27:36.861: %LWAPP-3-WLAN_ERR2: spam_lrad.c:20904 Unable to find WLAN 7 to be deleted; AP 00:3a:98:0d:e5:c0
*May 02 15:27:36.861: %LWAPP-3-WLAN_ERR2: spam_lrad.c:21261 Unable to find WLAN 7 to be deleted; AP 00:3a:98:0d:e5:c0
*May 02 15:27:36.859: %LWAPP-3-WLAN_ERR2: spam_lrad.c:20904 Unable to find WLAN 7 to be deleted; AP 00:3a:98:0d:e2:50
*May 02 15:27:36.859: %LWAPP-3-WLAN_ERR2: spam_lrad.c:21261 Unable to find WLAN 7 to be deleted; AP 00:3a:98:0d:e2:50
*May 02 15:27:36.857: %LWAPP-3-WLAN_ERR2: spam_lrad.c:20904 Unable to find WLAN 7 to be deleted; AP 00:3a:98:08:2f:70
*May 02 15:27:36.857: %LWAPP-3-WLAN_ERR2: spam_lrad.c:21261 Unable to find WLAN 7 to be deleted; AP 00:3a:98:08:2f:70
*May 02 15:27:36.856: %LWAPP-3-WLAN_ERR2: spam_lrad.c:20904 Unable to find WLAN 7 to be deleted; AP 00:3a:98:08:2f:60
*May 02 15:27:36.855: %LWAPP-3-WLAN_ERR2: spam_lrad.c:21261 Unable to find WLAN 7 to be deleted; AP 00:3a:98:08:2f:60
*May 02 15:22:35.811: %LWAPP-3-WLAN_ERR2: spam_lrad.c:20904 Unable to find WLAN 7 to be deleted; AP 00:3a:98:0d:e9:90
*May 02 15:22:35.811: %LWAPP-3-WLAN_ERR2: spam_lrad.c:21261 Unable to find WLAN 7 to be deleted; AP 00:3a:98:0d:e9:90
*May 02 15:22:35.809: %LWAPP-3-WLAN_ERR2: spam_lrad.c:20904 Unable to find WLAN 7 to be deleted; AP 00:3a:98:0d:e8:b0
*May 02 15:22:35.809: %LWAPP-3-WLAN_ERR2: spam_lrad.c:21261 Unable to find WLAN 7 to be deleted; AP 00:3a:98:0d:e8:b0
*May 02 15:22:35.808: %LWAPP-3-WLAN_ERR2: spam_lrad.c:20904 Unable to find WLAN 7 to be deleted; AP 00:3a:98:0d:e5:c0
*May 02 15:22:35.808: %LWAPP-3-WLAN_ERR2: spam_lrad.c:21261 Unable to find WLAN 7 to be deleted; AP 00:3a:98:0d:e5:c0
*May 02 15:22:35.806: %LWAPP-3-WLAN_ERR2: spam_lrad.c:20904 Unable to find WLAN 7 to be deleted; AP 00:3a:98:0d:e2:50
*May 02 15:22:35.806: %LWAPP-3-WLAN_ERR2: spam_lrad.c:21261 Unable to find WLAN 7 to be deleted; AP 00:3a:98:0d:e2:50
*May 02 15:22:35.804: %LWAPP-3-WLAN_ERR2: spam_lrad.c:20904 Unable to find WLAN 7 to be deleted; AP 00:3a:98:08:2f:70
*May 02 15:22:35.804: %LWAPP-3-WLAN_ERR2: spam_lrad.c:21261 Unable to find WLAN 7 to be deleted; AP 00:3a:98:08:2f:70
*May 02 15:22:35.802: %LWAPP-3-WLAN_ERR2: spam_lrad.c:20904 Unable to find WLAN 7 to be deleted; AP 00:3a:98:08:2f:60
*May 02 15:22:35.802: %LWAPP-3-WLAN_ERR2: spam_lrad.c:21261 Unable to find WLAN 7 to be deleted; AP 00:3a:98:08:2f:60
*May 02 15:18:32.227: %APF-1-PROC_RSN_WARP_IE_FAILED: apf_80211.c:2235 Could not process the RSN and WARP IEs. station not using WPA or WPA2 on WLAN requiring WPA and/or WPA2.MobileStation: 00:21:6b:39:a1:ac, SSID:voip,AP: c4:7d:4f:4b:a4:40.
*May 02 15:18:32.082: %APF-1-PROC_RSN_WARP_IE_FAILED: apf_80211.c:2235 Could not process the RSN and WARP IEs. station not using WPA or WPA2 on WLAN requiring WPA and/or WPA2.MobileStation: 00:21:6b:39:a1:ac, SSID:voip,AP: c4:7d:4f:4b:a4:40.
*May 02 15:18:31.995: %LWAPP-3-WLAN_ERR2: spam_lrad.c:20904 Unable to find WLAN 7 to be deleted; AP 00:3a:98:0d:e9:90
*May 02 15:18:31.995: %LWAPP-3-WLAN_ERR2: spam_lrad.c:21261 Unable to find WLAN 7 to be deleted; AP 00:3a:98:0d:e9:90
*May 02 15:18:31.993: %LWAPP-3-WLAN_ERR2: spam_lrad.c:20904 Unable to find WLAN 7 to be deleted; AP 00:3a:98:0d:e8:b0
*May 02 15:18:31.993: %LWAPP-3-WLAN_ERR2: spam_lrad.c:21261 Unable to find WLAN 7 to be deleted; AP 00:3a:98:0d:e8:b0
*May 02 15:18:31.992: %LWAPP-3-WLAN_ERR2: spam_lrad.c:20904 Unable to find WLAN 7 to be deleted; AP 00:3a:98:0d:e5:c0
*May 02 15:18:31.992: %LWAPP-3-WLAN_ERR2: spam_lrad.c:21261 Unable to find WLAN 7 to be deleted; AP 00:3a:98:0d:e5:c0
*May 02 15:18:31.989: %LWAPP-3-WLAN_ERR2: spam_lrad.c:20904 Unable to find WLAN 7 to be deleted; AP 00:3a:98:0d:e2:50
*May 02 15:18:31.989: %LWAPP-3-WLAN_ERR2: spam_lrad.c:21261 Unable to find WLAN 7 to be deleted; AP 00:3a:98:0d:e2:50
*May 02 15:18:31.984: %LWAPP-3-WLAN_ERR2: spam_lrad.c:20904 Unable to find WLAN 7 to be deleted; AP 00:3a:98:08:2f:70
*May 02 15:18:31.984: %LWAPP-3-WLAN_ERR2: spam_lrad.c:21261 Unable to find WLAN 7 to be deleted; AP 00:3a:98:08:2f:70
*May 02 15:18:31.979: %LWAPP-3-WLAN_ERR2: spam_lrad.c:20904 Unable to find WLAN 7 to be deleted; AP 00:3a:98:08:2f:60
*May 02 15:18:31.979: %LWAPP-3-WLAN_ERR2: spam_lrad.c:21261 Unable to find WLAN 7 to be deleted; AP 00:3a:98:08:2f:60
*May 02 15:17:49.474: %LWAPP-3-WLAN_ERR2: spam_lrad.c:20904 Unable to find WLAN 7 to be deleted; AP c4:7d:4f:4b:a6:d0
*May 02 15:17:49.474: %LWAPP-3-WLAN_ERR2: spam_lrad.c:21261 Unable to find WLAN 7 to be deleted; AP c4:7d:4f:4b:a6:d0
*May 02 15:17:49.472: %LWAPP-3-WLAN_ERR2: spam_lrad.c:20904 Unable to find WLAN 7 to be deleted; AP c4:7d:4f:4b:a4:40
*May 02 15:17:49.472: %LWAPP-3-WLAN_ERR2: spam_lrad.c:21261 Unable to find WLAN 7 to be deleted; AP c4:7d:4f:4b:a4:40
*May 02 15:17:49.470: %LWAPP-3-WLAN_ERR2: spam_lrad.c:20904 Unable to find WLAN 7 to be deleted; AP c4:7d:4f:4b:98:40
*May 02 15:17:49.470: %LWAPP-3-WLAN_ERR2: spam_lrad.c:21261 Unable to find WLAN 7 to be deleted; AP c4:7d:4f:4b:98:40
*May 02 15:17:49.468: %LWAPP-3-WLAN_ERR2: spam_lrad.c:20904 Unable to find WLAN 7 to be deleted; AP c4:7d:4f:46:f1:b0
*May 02 15:17:49.468: %LWAPP-3-WLAN_ERR2: spam_lrad.c:21261 Unable to find WLAN 7 to be deleted; AP c4:7d:4f:46:f1:b0
*May 02 15:17:49.465: %LWAPP-3-WLAN_ERR2: spam_lrad.c:20904 Unable to find WLAN 7 to be deleted; AP c4:7d:4f:46:f0:d0
*May 02 15:17:49.465: %LWAPP-3-WLAN_ERR2: spam_lrad.c:21261 Unable to find WLAN 7 to be deleted; AP c4:7d:4f:46:f0:d0
*May 02 15:17:49.460: %LWAPP-3-WLAN_ERR2: spam_lrad.c:20904 Unable to find WLAN 7 to be deleted; AP c4:7d:4f:46:e3:80
*May 02 15:17:49.460: %LWAPP-3-WLAN_ERR2: spam_lrad.c:21261 Unable to find WLAN 7 to be deleted; AP c4:7d:4f:46:e3:80
*May 02 15:17:49.457: %LWAPP-3-WLAN_ERR2: spam_lrad.c:20904 Unable to find WLAN 7 to be deleted; AP 00:3a:98:0d:e9:90
*May 02 15:17:49.457: %LWAPP-3-WLAN_ERR2: spam_lrad.c:21261 Unable to find WLAN 7 to be deleted; AP 00:3a:98:0d:e9:90
*May 02 15:17:49.456: %LWAPP-3-WLAN_ERR2: spam_lrad.c:20904 Unable to find WLAN 7 to be deleted; AP 00:3a:98:0d:e8:b0
*May 02 15:17:49.456: %LWAPP-3-WLAN_ERR2: spam_lrad.c:21261 Unable to find WLAN 7 to be deleted; AP 00:3a:98:0d:e8:b0
*May 02 15:17:49.452: %LWAPP-3-WLAN_ERR2: spam_lrad.c:20904 Unable to find WLAN 7 to be deleted; AP 00:3a:98:0d:e5:c0
*May 02 15:17:49.452: %LWAPP-3-WLAN_ERR2: spam_lrad.c:21261 Unable to find WLAN 7 to be deleted; AP 00:3a:98:0d:e5:c0
*May 02 15:17:49.447: %LWAPP-3-WLAN_ERR2: spam_lrad.c:20904 Unable to find WLAN 7 to be deleted; AP 00:3a:98:0d:e2:50
*May 02 15:17:49.447: %LWAPP-3-WLAN_ERR2: spam_lrad.c:21261 Unable to find WLAN 7 to be deleted; AP 00:3a:98:0d:e2:50
*May 02 15:17:49.443: %LWAPP-3-WLAN_ERR2: spam_lrad.c:20904 Unable to find WLAN 7 to be deleted; AP 00:3a:98:08:2f:70
*May 02 15:17:49.443: %LWAPP-3-WLAN_ERR2: spam_lrad.c:21261 Unable to find WLAN 7 to be deleted; AP 00:3a:98:08:2f:70
*May 02 15:17:49.440: %LWAPP-3-WLAN_ERR2: spam_lrad.c:20904 Unable to find WLAN 7 to be deleted; AP 00:3a:98:08:2f:60
*May 02 15:17:49.440: %LWAPP-3-WLAN_ERR2: spam_lrad.c:21261 Unable to find WLAN 7 to be deleted; AP 00:3a:98:08:2f:60
*May 02 15:16:24.677: %APF-1-DISCONECT_MOBILE_DUE_TO_WLAN_SW: apf_policy.c:541 Disconnecting mobile 00:21:6b:39:a1:ac due to switch of WLANs from 6(cisco_test) to 7(voip)
*May 02 15:14:20.572: %LWAPP-3-WLAN_ERR2: spam_lrad.c:20904 Unable to find WLAN 7 to be deleted; AP c4:7d:4f:4b:a6:d0
*May 02 15:14:20.572: %LWAPP-3-WLAN_ERR2: spam_lrad.c:21261 Unable to find WLAN 7 to be deleted; AP c4:7d:4f:4b:a6:d0
*May 02 15:14:20.571: %LWAPP-3-WLAN_ERR2: spam_lrad.c:20904 Unable to find WLAN 7 to be deleted; AP c4:7d:4f:4b:a4:40
*May 02 15:14:20.571: %LWAPP-3-WLAN_ERR2: spam_lrad.c:21261 Unable to find WLAN 7 to be deleted; AP c4:7d:4f:4b:a4:40
*May 02 15:14:20.571: %LWAPP-3-WLAN_ERR2: spam_lrad.c:20904 Unable to find WLAN 7 to be deleted; AP c4:7d:4f:4b:98:40
*May 02 15:14:20.571: %LWAPP-3-WLAN_ERR2: spam_lrad.c:21261 Unable to find WLAN 7 to be deleted; AP c4:7d:4f:4b:98:40
*May 02 15:14:20.569: %LWAPP-3-WLAN_ERR2: spam_lrad.c:20904 Unable to find WLAN 7 to be deleted; AP c4:7d:4f:46:f1:b0
*May 02 15:14:20.569: %LWAPP-3-WLAN_ERR2: spam_lrad.c:21261 Unable to find WLAN 7 to be deleted; AP c4:7d:4f:46:f1:b0
*May 02 15:14:20.569: %LWAPP-3-WLAN_ERR2: spam_lrad.c:20904 Unable to find WLAN 7 to be deleted; AP c4:7d:4f:46:f0:d0
*May 02 15:14:20.569: %LWAPP-3-WLAN_ERR2: spam_lrad.c:21261 Unable to find WLAN 7 to be deleted; AP c4:7d:4f:46:f0:d0
*May 02 15:14:20.568: %LWAPP-3-WLAN_ERR2: spam_lrad.c:20904 Unable to find WLAN 7 to be deleted; AP c4:7d:4f:46:e3:80
*May 02 15:14:20.568: %LWAPP-3-WLAN_ERR2: spam_lrad.c:21261 Unable to find WLAN 7 to be deleted; AP c4:7d:4f:46:e3:80
*May 02 15:14:20.568: %LWAPP-3-WLAN_ERR2: spam_lrad.c:20904 Unable to find WLAN 7 to be deleted; AP 00:3a:98:0d:e9:90
*May 02 15:14:20.568: %LWAPP-3-WLAN_ERR2: spam_lrad.c:21261 Unable to find WLAN 7 to be deleted; AP 00:3a:98:0d:e9:90
*May 02 15:14:20.568: %LWAPP-3-WLAN_ERR2: spam_lrad.c:20904 Unable to find WLAN 7 to be deleted; AP 00:3a:98:0d:e8:b0
*May 02 15:14:20.568: %LWAPP-3-WLAN_ERR2: spam_lrad.c:21261 Unable to find WLAN 7 to be deleted; AP 00:3a:98:0d:e8:b0
*May 02 15:14:20.567: %APF-3-SET_VAP_STATUS_FAILED: apf_api.c:15464 Could not Set the Status of Virtual Access point Entry.Encryption mode for static WEP does not match encryption mode for dynamic WEP on WLAN.Static WEP:1.Dynamic WEP:2. WLAN:'voip'
*May 02 15:14:20.566: %LWAPP-3-WLAN_ERR2: spam_lrad.c:20904 Unable to find WLAN 7 to be deleted; AP 00:3a:98:0d:e5:c0
*May 02 15:14:20.566: %LWAPP-3-WLAN_ERR2: spam_lrad.c:21261 Unable to find WLAN 7 to be deleted; AP 00:3a:98:0d:e5:c0
*May 02 15:14:20.564: %LWAPP-3-WLAN_ERR2: spam_lrad.c:20904 Unable to find WLAN 7 to be deleted; AP 00:3a:98:0d:e2:50
*May 02 15:14:20.564: %LWAPP-3-WLAN_ERR2: spam_lrad.c:21261 Unable to find WLAN 7 to be deleted; AP 00:3a:98:0d:e2:50
*May 02 15:14:20.562: %LWAPP-3-WLAN_ERR2: spam_lrad.c:20904 Unable to find WLAN 7 to be deleted; AP 00:3a:98:08:2f:70
*May 02 15:14:20.562: %LWAPP-3-WLAN_ERR2: spam_lrad.c:21261 Unable to find WLAN 7 to be deleted; AP 00:3a:98:08:2f:70
*May 02 15:14:20.560: %LWAPP-3-WLAN_ERR2: spam_lrad.c:20904 Unable to find WLAN 7 to be deleted; AP 00:3a:98:08:2f:60
*May 02 15:14:20.560: %LWAPP-3-WLAN_ERR2: spam_lrad.c:21261 Unable to find WLAN 7 to be deleted; AP 00:3a:98:08:2f:60
*May 02 15:08:45.139: %LWAPP-3-WLAN_ERR2: spam_lrad.c:20904 Unable to find WLAN 7 to be deleted; AP c4:7d:4f:4b:a6:d0
*May 02 15:08:45.139: %LWAPP-3-WLAN_ERR2: spam_lrad.c:21261 Unable to find WLAN 7 to be deleted; AP c4:7d:4f:4b:a6:d0
*May 02 15:08:45.137: %LWAPP-3-WLAN_ERR2: spam_lrad.c:20904 Unable to find WLAN 7 to be deleted; AP c4:7d:4f:4b:a4:40
*May 02 15:08:45.137: %LWAPP-3-WLAN_ERR2: spam_lrad.c:21261 Unable to find WLAN 7 to be deleted; AP c4:7d:4f:4b:a4:40
*May 02 15:08:45.135: %LWAPP-3-WLAN_ERR2: spam_lrad.c:20904 Unable to find WLAN 7 to be deleted; AP c4:7d:4f:4b:98:40
*May 02 15:08:45.135: %LWAPP-3-WLAN_ERR2: spam_lrad.c:21261 Unable to find WLAN 7 to be deleted; AP c4:7d:4f:4b:98:40
*May 02 15:08:45.134: %LWAPP-3-WLAN_ERR2: spam_lrad.c:20904 Unable to find WLAN 7 to be deleted; AP c4:7d:4f:46:f1:b0
*May 02 15:08:45.133: %LWAPP-3-WLAN_ERR2: spam_lrad.c:21261 Unable to find WLAN 7 to be deleted; AP c4:7d:4f:46:f1:b0
*May 02 15:08:45.132: %LWAPP-3-WLAN_ERR2: spam_lrad.c:20904 Unable to find WLAN 7 to be deleted; AP c4:7d:4f:46:f0:d0
*May 02 15:08:45.132: %LWAPP-3-WLAN_ERR2: spam_lrad.c:21261 Unable to find WLAN 7 to be deleted; AP c4:7d:4f:46:f0:d0
*May 02 15:08:45.131: %LWAPP-3-WLAN_ERR2: spam_lrad.c:20904 Unable to find WLAN 7 to be deleted; AP c4:7d:4f:46:e3:80
*May 02 15:08:45.130: %LWAPP-3-WLAN_ERR2: spam_lrad.c:21261 Unable to find WLAN 7 to be deleted; AP c4:7d:4f:46:e3:80
*May 02 15:08:45.129: %LWAPP-3-WLAN_ERR2: spam_lrad.c:20904 Unable to find WLAN 7 to be deleted; AP 00:3a:98:0d:e9:90
*May 02 15:08:45.129: %LWAPP-3-WLAN_ERR2: spam_lrad.c:21261 Unable to find WLAN 7 to be deleted; AP 00:3a:98:0d:e9:90
*May 02 15:08:45.128: %LWAPP-3-WLAN_ERR2: spam_lrad.c:20904 Unable to find WLAN 7 to be deleted; AP 00:3a:98:0d:e8:b0
*May 02 15:08:45.128: %LWAPP-3-WLAN_ERR2: spam_lrad.c:21261 Unable to find WLAN 7 to be deleted; AP 00:3a:98:0d:e8:b0
*May 02 15:08:45.126: %LWAPP-3-WLAN_ERR2: spam_lrad.c:20904 Unable to find WLAN 7 to be deleted; AP 00:3a:98:0d:e5:c0
*May 02 15:08:45.126: %LWAPP-3-WLAN_ERR2: spam_lrad.c:21261 Unable to find WLAN 7 to be deleted; AP 00:3a:98:0d:e5:c0
*May 02 15:08:45.124: %LWAPP-3-WLAN_ERR2: spam_lrad.c:20904 Unable to find WLAN 7 to be deleted; AP 00:3a:98:0d:e2:50
*May 02 15:08:45.124: %LWAPP-3-WLAN_ERR2: spam_lrad.c:21261 Unable to find WLAN 7 to be deleted; AP 00:3a:98:0d:e2:50
*May 02 15:08:45.122: %LWAPP-3-WLAN_ERR2: spam_lrad.c:20904 Unable to find WLAN 7 to be deleted; AP 00:3a:98:08:2f:70
*May 02 15:08:45.122: %LWAPP-3-WLAN_ERR2: spam_lrad.c:21261 Unable to find WLAN 7 to be deleted; AP 00:3a:98:08:2f:70
*May 02 15:08:45.120: %LWAPP-3-WLAN_ERR2: spam_lrad.c:20904 Unable to find WLAN 7 to be deleted; AP 00:3a:98:08:2f:60
*May 02 15:08:45.120: %LWAPP-3-WLAN_ERR2: spam_lrad.c:21261 Unable to find WLAN 7 to be deleted; AP 00:3a:98:08:2f:60
*May 02 15:08:43.623: %APF-1-DISCONECT_MOBILE_DUE_TO_WLAN_SW: apf_policy.c:541 Disconnecting mobile 00:21:6b:39:a1:ac due to switch of WLANs from 4(CGC-7FL-WLAN) to 6(cisco_test)
*May 02 15:07:35.339: %APF-1-DISCONECT_MOBILE_DUE_TO_WLAN_SW: apf_policy.c:541 Disconnecting mobile 00:21:6b:39:a1:ac due to switch of WLANs from 7(voip) to 4(CGC-7FL-WLAN)
*May 02 15:06:55.072: %AAA-3-EAPMETHOD_ADD_FAILED: localeap_db.c:2716 Unable to add method 'peap' to EAP profile for user 'test'. method already exist.
*May 02 15:06:55.072: %AAA-3-EAPMETHOD_ADD_FAILED: localeap_db.c:2716 Unable to add method 'tls' to EAP profile for user 'test'. method already exist.
*May 02 15:06:55.072: %AAA-3-EAPMETHOD_ADD_FAILED: localeap_db.c:2716 Unable to add method 'fast' to EAP profile for user 'test'. method already exist.
*May 02 15:06:55.072: %AAA-3-EAPMETHOD_ADD_FAILED: localeap_db.c:2716 Unable to add method 'leap' to EAP profile for user 'test'. method already exist.
*May 02 15:06:27.672: %DOT1X-3-MAX_EAP_RETRIES: 1x_auth_pae.c:2872 Max EAP identity request retries (3) exceeded for client 00:21:6b:39:a1:ac
*May 02 15:05:27.648: %DOT1X-3-MAX_EAP_RETRIES: 1x_auth_pae.c:2872I have tried with WPA-PSK and tried the notebook to join it is joining but the Phone is not joiining getting the same error.
connection failed.
*May 02 15:37:52.629: %LWAPP-3-WLAN_ERR2: spam_lrad.c:20904 Unable to find WLAN 7 to be deleted; AP 00:3a:98:0d:e9:90
*May 02 15:37:52.629: %LWAPP-3-WLAN_ERR2: spam_lrad.c:21261 Unable to find WLAN 7 to be deleted; AP 00:3a:98:0d:e9:90
*May 02 15:37:52.628: %LWAPP-3-WLAN_ERR2: spam_lrad.c:20904 Unable to find WLAN 7 to be deleted; AP 00:3a:98:0d:e8:b0
*May 02 15:37:52.628: %LWAPP-3-WLAN_ERR2: spam_lrad.c:21261 Unable to find WLAN 7 to be deleted; AP 00:3a:98:0d:e8:b0
*May 02 15:37:52.628: %LWAPP-3-WLAN_ERR2: spam_lrad.c:20904 Unable to find WLAN 7 to be deleted; AP 00:3a:98:0d:e5:c0
*May 02 15:37:52.628: %LWAPP-3-WLAN_ERR2: spam_lrad.c:21261 Unable to find WLAN 7 to be deleted; AP 00:3a:98:0d:e5:c0
*May 02 15:37:52.626: %LWAPP-3-WLAN_ERR2: spam_lrad.c:20904 Unable to find WLAN 7 to be deleted; AP 00:3a:98:0d:e2:50
*May 02 15:37:52.626: %LWAPP-3-WLAN_ERR2: spam_lrad.c:21261 Unable to find WLAN 7 to be deleted; AP 00:3a:98:0d:e2:50
*May 02 15:37:52.625: %LWAPP-3-WLAN_ERR2: spam_lrad.c:20904 Unable to find WLAN 7 to be deleted; AP 00:3a:98:08:2f:70
*May 02 15:37:52.625: %LWAPP-3-WLAN_ERR2: spam_lrad.c:21261 Unable to find WLAN 7 to be deleted; AP 00:3a:98:08:2f:70
*May 02 15:37:52.623: %LWAPP-3-WLAN_ERR2: spam_lrad.c:20904 Unable to find WLAN 7 to be deleted; AP 00:3a:98:08:2f:60
*May 02 15:37:52.623: %LWAPP-3-WLAN_ERR2: spam_lrad.c:21261 Unable to find WLAN 7 to be deleted; AP 00:3a:98:08:2f:60
*May 02 15:27:36.864: %LWAPP-3-WLAN_ERR2: spam_lrad.c:20904 Unable to find WLAN 7 to be deleted; AP 00:3a:98:0d:e9:90
*May 02 15:27:36.864: %LWAPP-3-WLAN_ERR2: spam_lrad.c:21261 Unable to find WLAN 7 to be deleted; AP 00:3a:98:0d:e9:90
*May 02 15:27:36.863: %LWAPP-3-WLAN_ERR2: spam_lrad.c:20904 Unable to find WLAN 7 to be deleted; AP 00:3a:98:0d:e8:b0
*May 02 15:27:36.863: %LWAPP-3-WLAN_ERR2: spam_lrad.c:21261 Unable to find WLAN 7 to be deleted; AP 00:3a:98:0d:e8:b0
*May 02 15:27:36.861: %LWAPP-3-WLAN_ERR2: spam_lrad.c:20904 Unable to find WLAN 7 to be deleted; AP 00:3a:98:0d:e5:c0
*May 02 15:27:36.861: %LWAPP-3-WLAN_ERR2: spam_lrad.c:21261 Unable to find WLAN 7 to be deleted; AP 00:3a:98:0d:e5:c0
*May 02 15:27:36.859: %LWAPP-3-WLAN_ERR2: spam_lrad.c:20904 Unable to find WLAN 7 to be deleted; AP 00:3a:98:0d:e2:50
*May 02 15:27:36.859: %LWAPP-3-WLAN_ERR2: spam_lrad.c:21261 Unable to find WLAN 7 to be deleted; AP 00:3a:98:0d:e2:50
*May 02 15:27:36.857: %LWAPP-3-WLAN_ERR2: spam_lrad.c:20904 Unable to find WLAN 7 to be deleted; AP 00:3a:98:08:2f:70
*May 02 15:27:36.857: %LWAPP-3-WLAN_ERR2: spam_lrad.c:21261 Unable to find WLAN 7 to be deleted; AP 00:3a:98:08:2f:70
*May 02 15:27:36.856: %LWAPP-3-WLAN_ERR2: spam_lrad.c:20904 Unable to find WLAN 7 to be deleted; AP 00:3a:98:08:2f:60
*May 02 15:27:36.855: %LWAPP-3-WLAN_ERR2: spam_lrad.c:21261 Unable to find WLAN 7 to be deleted; AP 00:3a:98:08:2f:60
*May 02 15:22:35.811: %LWAPP-3-WLAN_ERR2: spam_lrad.c:20904 Unable to find WLAN 7 to be deleted; AP 00:3a:98:0d:e9:90
*May 02 15:22:35.811: %LWAPP-3-WLAN_ERR2: spam_lrad.c:21261 Unable to find WLAN 7 to be deleted; AP 00:3a:98:0d:e9:90
*May 02 15:22:35.809: %LWAPP-3-WLAN_ERR2: spam_lrad.c:20904 Unable to find WLAN 7 to be deleted; AP 00:3a:98:0d:e8:b0
*May 02 15:22:35.809: %LWAPP-3-WLAN_ERR2: spam_lrad.c:21261 Unable to find WLAN 7 to be deleted; AP 00:3a:98:0d:e8:b0
*May 02 15:22:35.808: %LWAPP-3-WLAN_ERR2: spam_lrad.c:20904 Unable to find WLAN 7 to be deleted; AP 00:3a:98:0d:e5:c0
*May 02 15:22:35.808: %LWAPP-3-WLAN_ERR2: spam_lrad.c:21261 Unable to find WLAN 7 to be deleted; AP 00:3a:98:0d:e5:c0
*May 02 15:22:35.806: %LWAPP-3-WLAN_ERR2: spam_lrad.c:20904 Unable to find WLAN 7 to be deleted; AP 00:3a:98:0d:e2:50
*May 02 15:22:35.806: %LWAPP-3-WLAN_ERR2: spam_lrad.c:21261 Unable to find WLAN 7 to be deleted; AP 00:3a:98:0d:e2:50
*May 02 15:22:35.804: %LWAPP-3-WLAN_ERR2: spam_lrad.c:20904 Unable to find WLAN 7 to be deleted; AP 00:3a:98:08:2f:70
*May 02 15:22:35.804: %LWAPP-3-WLAN_ERR2: spam_lrad.c:21261 Unable to find WLAN 7 to be deleted; AP 00:3a:98:08:2f:70
*May 02 15:22:35.802: %LWAPP-3-WLAN_ERR2: spam_lrad.c:20904 Unable to find WLAN 7 to be deleted; AP 00:3a:98:08:2f:60
*May 02 15:22:35.802: %LWAPP-3-WLAN_ERR2: spam_lrad.c:21261 Unable to find WLAN 7 to be deleted; AP 00:3a:98:08:2f:60
*May 02 15:18:32.227: %APF-1-PROC_RSN_WARP_IE_FAILED: apf_80211.c:2235 Could not process the RSN and WARP IEs. station not using WPA or WPA2 on WLAN requiring WPA and/or WPA2.MobileStation: 00:21:6b:39:a1:ac, SSID:voip,AP: c4:7d:4f:4b:a4:40.
*May 02 15:18:32.082: %APF-1-PROC_RSN_WARP_IE_FAILED: apf_80211.c:2235 Could not process the RSN and WARP IEs. station not using WPA or WPA2 on WLAN requiring WPA and/or WPA2.MobileStation: 00:21:6b:39:a1:ac, SSID:voip,AP: c4:7d:4f:4b:a4:40.
*May 02 15:18:31.995: %LWAPP-3-WLAN_ERR2: spam_lrad.c:20904 Unable to find WLAN 7 to be deleted; AP 00:3a:98:0d:e9:90
*May 02 15:18:31.995: %LWAPP-3-WLAN_ERR2: spam_lrad.c:21261 Unable to find WLAN 7 to be deleted; AP 00:3a:98:0d:e9:90
*May 02 15:18:31.993: %LWAPP-3-WLAN_ERR2: spam_lrad.c:20904 Unable to find WLAN 7 to be deleted; AP 00:3a:98:0d:e8:b0
*May 02 15:18:31.993: %LWAPP-3-WLAN_ERR2: spam_lrad.c:21261 Unable to find WLAN 7 to be deleted; AP 00:3a:98:0d:e8:b0
*May 02 15:18:31.992: %LWAPP-3-WLAN_ERR2: spam_lrad.c:20904 Unable to find WLAN 7 to be deleted; AP 00:3a:98:0d:e5:c0
*May 02 15:18:31.992: %LWAPP-3-WLAN_ERR2: spam_lrad.c:21261 Unable to find WLAN 7 to be deleted; AP 00:3a:98:0d:e5:c0
*May 02 15:18:31.989: %LWAPP-3-WLAN_ERR2: spam_lrad.c:20904 Unable to find WLAN 7 to be deleted; AP 00:3a:98:0d:e2:50
*May 02 15:18:31.989: %LWAPP-3-WLAN_ERR2: spam_lrad.c:21261 Unable to find WLAN 7 to be deleted; AP 00:3a:98:0d:e2:50
*May 02 15:18:31.984: %LWAPP-3-WLAN_ERR2: spam_lrad.c:20904 Unable to find WLAN 7 to be deleted; AP 00:3a:98:08:2f:70
*May 02 15:18:31.984: %LWAPP-3-WLAN_ERR2: spam_lrad.c:21261 Unable to find WLAN 7 to be deleted; AP 00:3a:98:08:2f:70
*May 02 15:18:31.979: %LWAPP-3-WLAN_ERR2: spam_lrad.c:20904 Unable to find WLAN 7 to be deleted; AP 00:3a:98:08:2f:60
*May 02 15:18:31.979: %LWAPP-3-WLAN_ERR2: spam_lrad.c:21261 Unable to find WLAN 7 to be deleted; AP 00:3a:98:08:2f:60
*May 02 15:17:49.474: %LWAPP-3-WLAN_ERR2: spam_lrad.c:20904 Unable to find WLAN 7 to be deleted; AP c4:7d:4f:4b:a6:d0
*May 02 15:17:49.474: %LWAPP-3-WLAN_ERR2: spam_lrad.c:21261 Unable to find WLAN 7 to be deleted; AP c4:7d:4f:4b:a6:d0
*May 02 15:17:49.472: %LWAPP-3-WLAN_ERR2: spam_lrad.c:20904 Unable to find WLAN 7 to be deleted; AP c4:7d:4f:4b:a4:40
*May 02 15:17:49.472: %LWAPP-3-WLAN_ERR2: spam_lrad.c:21261 Unable to find WLAN 7 to be deleted; AP c4:7d:4f:4b:a4:40
*May 02 15:17:49.470: %LWAPP-3-WLAN_ERR2: spam_lrad.c:20904 Unable to find WLAN 7 to be deleted; AP c4:7d:4f:4b:98:40
*May 02 15:17:49.470: %LWAPP-3-WLAN_ERR2: spam_lrad.c:21261 Unable to find WLAN 7 to be deleted; AP c4:7d:4f:4b:98:40
*May 02 15:17:49.468: %LWAPP-3-WLAN_ERR2: spam_lrad.c:20904 Unable to find WLAN 7 to be deleted; AP c4:7d:4f:46:f1:b0
*May 02 15:17:49.468: %LWAPP-3-WLAN_ERR2: spam_lrad.c:21261 Unable to find WLAN 7 to be deleted; AP c4:7d:4f:46:f1:b0
*May 02 15:17:49.465: %LWAPP-3-WLAN_ERR2: spam_lrad.c:20904 Unable to find WLAN 7 to be deleted; AP c4:7d:4f:46:f0:d0
*May 02 15:17:49.465: %LWAPP-3-WLAN_ERR2: spam_lrad.c:21261 Unable to find WLAN 7 to be deleted; AP c4:7d:4f:46:f0:d0
*May 02 15:17:49.460: %LWAPP-3-WLAN_ERR2: spam_lrad.c:20904 Unable to find WLAN 7 to be deleted; AP c4:7d:4f:46:e3:80
*May 02 15:17:49.460: %LWAPP-3-WLAN_ERR2: spam_lrad.c:21261 Unable to find WLAN 7 to be deleted; AP c4:7d:4f:46:e3:80
*May 02 15:17:49.457: %LWAPP-3-WLAN_ERR2: spam_lrad.c:20904 Unable to find WLAN 7 to be deleted; AP 00:3a:98:0d:e9:90
*May 02 15:17:49.457: %LWAPP-3-WLAN_ERR2: spam_lrad.c:21261 Unable to find WLAN 7 to be deleted; AP 00:3a:98:0d:e9:90
*May 02 15:17:49.456: %LWAPP-3-WLAN_ERR2: spam_lrad.c:20904 Unable to find WLAN 7 to be deleted; AP 00:3a:98:0d:e8:b0
*May 02 15:17:49.456: %LWAPP-3-WLAN_ERR2: spam_lrad.c:21261 Unable to find WLAN 7 to be deleted; AP 00:3a:98:0d:e8:b0
*May 02 15:17:49.452: %LWAPP-3-WLAN_ERR2: spam_lrad.c:20904 Unable to find WLAN 7 to be deleted; AP 00:3a:98:0d:e5:c0
*May 02 15:17:49.452: %LWAPP-3-WLAN_ERR2: spam_lrad.c:21261 Unable to find WLAN 7 to be deleted; AP 00:3a:98:0d:e5:c0
*May 02 15:17:49.447: %LWAPP-3-WLAN_ERR2: spam_lrad.c:20904 Unable to find WLAN 7 to be deleted; AP 00:3a:98:0d:e2:50
*May 02 15:17:49.447: %LWAPP-3-WLAN_ERR2: spam_lrad.c:21261 Unable to find WLAN 7 to be deleted; AP 00:3a:98:0d:e2:50
*May 02 15:17:49.443: %LWAPP-3-WLAN_ERR2: spam_lrad.c:20904 Unable to find WLAN 7 to be deleted; AP 00:3a:98:08:2f:70
*May 02 15:17:49.443: %LWAPP-3-WLAN_ERR2: spam_lrad.c:21261 Unable to find WLAN 7 to be deleted; AP 00:3a:98:08:2f:70
*May 02 15:17:49.440: %LWAPP-3-WLAN_ERR2: spam_lrad.c:20904 Unable to find WLAN 7 to be deleted; AP 00:3a:98:08:2f:60
*May 02 15:17:49.440: %LWAPP-3-WLAN_ERR2: spam_lrad.c:21261 Unable to find WLAN 7 to be deleted; AP 00:3a:98:08:2f:60
*May 02 15:16:24.677: %APF-1-DISCONECT_MOBILE_DUE_TO_WLAN_SW: apf_policy.c:541 Disconnecting mobile 00:21:6b:39:a1:ac due to switch of WLANs from 6(cisco_test) to 7(voip)
*May 02 15:14:20.572: %LWAPP-3-WLAN_ERR2: spam_lrad.c:20904 Unable to find WLAN 7 to be deleted; AP c4:7d:4f:4b:a6:d0
*May 02 15:14:20.572: %LWAPP-3-WLAN_ERR2: spam_lrad.c:21261 Unable to find WLAN 7 to be deleted; AP c4:7d:4f:4b:a6:d0
*May 02 15:14:20.571: %LWAPP-3-WLAN_ERR2: spam_lrad.c:20904 Unable to find WLAN 7 to be deleted; AP c4:7d:4f:4b:a4:40
*May 02 15:14:20.571: %LWAPP-3-WLAN_ERR2: spam_lrad.c:21261 Unable to find WLAN 7 to be deleted; AP c4:7d:4f:4b:a4:40
*May 02 15:14:20.571: %LWAPP-3-WLAN_ERR2: spam_lrad.c:20904 Unable to find WLAN 7 to be deleted; AP c4:7d:4f:4b:98:40
*May 02 15:14:20.571: %LWAPP-3-WLAN_ERR2: spam_lrad.c:21261 Unable to find WLAN 7 to be deleted; AP c4:7d:4f:4b:98:40
*May 02 15:14:20.569: %LWAPP-3-WLAN_ERR2: spam_lrad.c:20904 Unable to find WLAN 7 to be deleted; AP c4:7d:4f:46:f1:b0
*May 02 15:14:20.569: %LWAPP-3-WLAN_ERR2: spam_lrad.c:21261 Unable to find WLAN 7 to be deleted; AP c4:7d:4f:46:f1:b0
*May 02 15:14:20.569: %LWAPP-3-WLAN_ERR2: spam_lrad.c:20904 Unable to find WLAN 7 to be deleted; AP c4:7d:4f:46:f0:d0
*May 02 15:14:20.569: %LWAPP-3-WLAN_ERR2: spam_lrad.c:21261 Unable to find WLAN 7 to be deleted; AP c4:7d:4f:46:f0:d0
*May 02 15:14:20.568: %LWAPP-3-WLAN_ERR2: spam_lrad.c:20904 Unable to find WLAN 7 to be deleted; AP c4:7d:4f:46:e3:80
*May 02 15:14:20.568: %LWAPP-3-WLAN_ERR2: spam_lrad.c:21261 Unable to find WLAN 7 to be deleted; AP c4:7d:4f:46:e3:80
*May 02 15:14:20.568: %LWAPP-3-WLAN_ERR2: spam_lrad.c:20904 Unable to find WLAN 7 to be deleted; AP 00:3a:98:0d:e9:90
*May 02 15:14:20.568: %LWAPP-3-WLAN_ERR2: spam_lrad.c:21261 Unable to find WLAN 7 to be deleted; AP 00:3a:98:0d:e9:90
*May 02 15:14:20.568: %LWAPP-3-WLAN_ERR2: spam_lrad.c:20904 Unable to find WLAN 7 to be deleted; AP 00:3a:98:0d:e8:b0
*May 02 15:14:20.568: %LWAPP-3-WLAN_ERR2: spam_lrad.c:21261 Unable to find WLAN 7 to be deleted; AP 00:3a:98:0d:e8:b0
*May 02 15:14:20.567: %APF-3-SET_VAP_STATUS_FAILED: apf_api.c:15464 Could not Set the Status of Virtual Access point Entry.Encryption mode for static WEP does not match encryption mode for dynamic WEP on WLAN.Static WEP:1.Dynamic WEP:2. WLAN:'voip'
*May 02 15:14:20.566: %LWAPP-3-WLAN_ERR2: spam_lrad.c:20904 Unable to find WLAN 7 to be deleted; AP 00:3a:98:0d:e5:c0
*May 02 15:14:20.566: %LWAPP-3-WLAN_ERR2: spam_lrad.c:21261 Unable to find WLAN 7 to be deleted; AP 00:3a:98:0d:e5:c0
*May 02 15:14:20.564: %LWAPP-3-WLAN_ERR2: spam_lrad.c:20904 Unable to find WLAN 7 to be deleted; AP 00:3a:98:0d:e2:50
*May 02 15:14:20.564: %LWAPP-3-WLAN_ERR2: spam_lrad.c:21261 Unable to find WLAN 7 to be deleted; AP 00:3a:98:0d:e2:50
*May 02 15:14:20.562: %LWAPP-3-WLAN_ERR2: spam_lrad.c:20904 Unable to find WLAN 7 to be deleted; AP 00:3a:98:08:2f:70
*May 02 15:14:20.562: %LWAPP-3-WLAN_ERR2: spam_lrad.c:21261 Unable to find WLAN 7 to be deleted; AP 00:3a:98:08:2f:70
*May 02 15:14:20.560: %LWAPP-3-WLAN_ERR2: spam_lrad.c:20904 Unable to find WLAN 7 to be deleted; AP 00:3a:98:08:2f:60
*May 02 15:14:20.560: %LWAPP-3-WLAN_ERR2: spam_lrad.c:21261 Unable to find WLAN 7 to be deleted; AP 00:3a:98:08:2f:60
*May 02 15:08:45.139: %LWAPP-3-WLAN_ERR2: spam_lrad.c:20904 Unable to find WLAN 7 to be deleted; AP c4:7d:4f:4b:a6:d0
*May 02 15:08:45.139: %LWAPP-3-WLAN_ERR2: spam_lrad.c:21261 Unable to find WLAN 7 to be deleted; AP c4:7d:4f:4b:a6:d0
*May 02 15:08:45.137: %LWAPP-3-WLAN_ERR2: spam_lrad.c:20904 Unable to find WLAN 7 to be deleted; AP c4:7d:4f:4b:a4:40
*May 02 15:08:45.137: %LWAPP-3-WLAN_ERR2: spam_lrad.c:21261 Unable to find WLAN 7 to be deleted; AP c4:7d:4f:4b:a4:40
*May 02 15:08:45.135: %LWAPP-3-WLAN_ERR2: spam_lrad.c:20904 Unable to find WLAN 7 to be deleted; AP c4:7d:4f:4b:98:40
*May 02 15:08:45.135: %LWAPP-3-WLAN_ERR2: spam_lrad.c:21261 Unable to find WLAN 7 to be deleted; AP c4:7d:4f:4b:98:40
*May 02 15:08:45.134: %LWAPP-3-WLAN_ERR2: spam_lrad.c:20904 Unable to find WLAN 7 to be deleted; AP c4:7d:4f:46:f1:b0
*May 02 15:08:45.133: %LWAPP-3-WLAN_ERR2: spam_lrad.c:21261 Unable to find WLAN 7 to be deleted; AP c4:7d:4f:46:f1:b0
*May 02 15:08:45.132: %LWAPP-3-WLAN_ERR2: spam_lrad.c:20904 Unable to find WLAN 7 to be deleted; AP c4:7d:4f:46:f0:d0
*May 02 15:08:45.132: %LWAPP-3-WLAN_ERR2: spam_lrad.c:21261 Unable to find WLAN 7 to be deleted; AP c4:7d:4f:46:f0:d0
*May 02 15:08:45.131: %LWAPP-3-WLAN_ERR2: spam_lrad.c:20904 Unable to find WLAN 7 to be deleted; AP c4:7d:4f:46:e3:80
*May 02 15:08:45.130: %LWAPP-3-WLAN_ERR2: spam_lrad.c:21261 Unable to find WLAN 7 to be deleted; AP c4:7d:4f:46:e3:80
*May 02 15:08:45.129: %LWAPP-3-WLAN_ERR2: spam_lrad.c:20904 Unable to find WLAN 7 to be deleted; AP 00:3a:98:0d:e9:90
*May 02 15:08:45.129: %LWAPP-3-WLAN_ERR2: spam_lrad.c:21261 Unable to find WLAN 7 to be deleted; AP 00:3a:98:0d:e9:90
*May 02 15:08:45.128: %LWAPP-3-WLAN_ERR2: spam_lrad.c:20904 Unable to find WLAN 7 to be deleted; AP 00:3a:98:0d:e8:b0
*May 02 15:08:45.128: %LWAPP-3-WLAN_ERR2: spam_lrad.c:21261 Unable to find WLAN 7 to be deleted; AP 00:3a:98:0d:e8:b0
*May 02 15:08:45.126: %LWAPP-3-WLAN_ERR2: spam_lrad.c:20904 Unable to find WLAN 7 to be deleted; AP 00:3a:98:0d:e5:c0
*May 02 15:08:45.126: %LWAPP-3-WLAN_ERR2: spam_lrad.c:21261 Unable to find WLAN 7 to be deleted; AP 00:3a:98:0d:e5:c0
*May 02 15:08:45.124: %LWAPP-3-WLAN_ERR2: spam_lrad.c:20904 Unable to find WLAN 7 to be deleted; AP 00:3a:98:0d:e2:50
*May 02 15:08:45.124: %LWAPP-3-WLAN_ERR2: spam_lrad.c:21261 Unable to find WLAN 7 to be deleted; AP 00:3a:98:0d:e2:50
*May 02 15:08:45.122: %LWAPP-3-WLAN_ERR2: spam_lrad.c:20904 Unable to find WLAN 7 to be deleted; AP 00:3a:98:08:2f:70
*May 02 15:08:45.122: %LWAPP-3-WLAN_ERR2: spam_lrad.c:21261 Unable to find WLAN 7 to be deleted; AP 00:3a:98:08:2f:70
*May 02 15:08:45.120: %LWAPP-3-WLAN_ERR2: spam_lrad.c:20904 Unable to find WLAN 7 to be deleted; AP 00:3a:98:08:2f:60
*May 02 15:08:45.120: %LWAPP-3-WLAN_ERR2: spam_lrad.c:21261 Unable to find WLAN 7 to be deleted; AP 00:3a:98:08:2f:60
*May 02 15:08:43.623: %APF-1-DISCONECT_MOBILE_DUE_TO_WLAN_SW: apf_policy.c:541 Disconnecting mobile 00:21:6b:39:a1:ac due to switch of WLANs from 4(CGC-7FL-WLAN) to 6(cisco_test)
*May 02 15:07:35.339: %APF-1-DISCONECT_MOBILE_DUE_TO_WLAN_SW: apf_policy.c:541 Disconnecting mobile 00:21:6b:39:a1:ac due to switch of WLANs from 7(voip) to 4(CGC-7FL-WLAN)
*May 02 15:06:55.072: %AAA-3-EAPMETHOD_ADD_FAILED: localeap_db.c:2716 Unable to add method 'peap' to EAP profile for user 'test'. method already exist.
*May 02 15:06:55.072: %AAA-3-EAPMETHOD_ADD_FAILED: localeap_db.c:2716 Unable to add method 'tls' to EAP profile for user 'test'. method already exist.
*May 02 15:06:55.072: %AAA-3-EAPMETHOD_ADD_FAILED: localeap_db.c:2716 Unable to add method 'fast' to EAP profile for user 'test'. method already exist.
*May 02 15:06:55.072: %AAA-3-EAPMETHOD_ADD_FAILED: localeap_db.c:2716 Unable to add method 'leap' to EAP profile for user 'test'. method already exist.
*May 02 15:06:27.672: %DOT1X-3-MAX_EAP_RETRIES: 1x_auth_pae.c:2872 Max EAP identity request retries (3) exceeded for client 00:21:6b:39:a1:ac
*May 02 15:05:27.648: %DOT1X-3-MAX_EAP_RETRIES: 1x_auth_pae.c:2872 -
I upgraded a controller yesterday 5508 it went from a low code version 6.x to 6.0.196.0 then to 7.0.116.0. However although all the access points joined code 6.0.196.0 they refused to join 7.0.116.0. The aps are all 1242s.
The country codes etc were all fine so I do not understand what was going on.
Any ideas?
*spamApTask0: Jun 26 16:07:44.734: 00:3a:99:db:f3:20 Discovery Request from 10.0.0.183:55065
*spamApTask0: Jun 26 16:07:44.734: 00:3a:99:db:f3:20 Join Priority Processing status = 0, Incoming Ap's Priority 1, MaxLrads = 25, joined Aps =0
*spamApTask0: Jun 26 16:07:44.735: 00:3a:99:db:f3:20 Discovery Response sent to 10.0.0.183:55065
*spamApTask0: Jun 26 16:07:44.735: 00:3a:99:db:f3:20 Received LWAPP DISCOVERY REQUEST to e8:b7:48:9b:86:4f on port '13'
*spamApTask0: Jun 26 16:07:44.735: 00:3a:99:db:f3:20 Discarding discovery request in LWAPP from AP supporting CAPWAP
*spamApTask0: Jun 26 16:07:44.735: 00:3a:99:db:f3:20 Discovery Request from 10.0.0.183:55065
*spamApTask0: Jun 26 16:07:44.735: 00:3a:99:db:f3:20 Join Priority Processing status = 0, Incoming Ap's Priority 1, MaxLrads = 25, joined Aps =0
*spamApTask0: Jun 26 16:07:44.735: 00:3a:99:db:f3:20 Discovery Response sent to 10.0.0.183:55065
*spamApTask7: Jun 26 16:07:45.308: 00:3a:99:db:fa:20 Discovery Request from 10.0.0.95:55080
*spamApTask7: Jun 26 16:07:45.308: 00:3a:99:db:fa:20 Join Priority Processing status = 0, Incoming Ap's Priority 1, MaxLrads = 25, joined Aps =0
*spamApTask0: Jun 26 16:07:45.308: 00:3a:99:db:fa:20 Received LWAPP DISCOVERY REQUEST to e8:b7:48:9b:86:4f on port '13'
*spamApTask0: Jun 26 16:07:45.308: 00:3a:99:db:fa:20 Discarding discovery request in LWAPP from AP supporting CAPWAP
*spamApTask7: Jun 26 16:07:45.308: 00:3a:99:db:fa:20 Discovery Response sent to 10.0.0.95:55080
*spamApTask7: Jun 26 16:07:45.309: 00:3a:99:db:fa:20 Discovery Request from 10.0.0.95:55080
*spamApTask7: Jun 26 16:07:45.309: 00:3a:99:db:fa:20 Join Priority Processing status = 0, Incoming Ap's Priority 1, MaxLrads = 25, joined Aps =0
*spamApTask7: Jun 26 16:07:45.309: 00:3a:99:db:fa:20 Discovery Response sent to 10.0.0.95:55080
*spamApTask7: Jun 26 16:07:45.511: 00:13:c3:e1:4c:e0 Discovery Request from 10.0.1.232:20023
*spamApTask7: Jun 26 16:07:45.511: 00:13:c3:e1:4c:e0 Join Priority Processing status = 0, Incoming Ap's Priority 1, MaxLrads = 25, joined Aps =0
*spamApTask7: Jun 26 16:07:45.511: 00:13:c3:e1:4c:e0 Discovery Response sent to 10.0.1.232:20023
*spamApTask0: Jun 26 16:07:45.511: 00:13:c3:e1:4c:e0 Received LWAPP DISCOVERY REQUEST to e8:b7:48:9b:86:4f on port '13'
*spamApTask0: Jun 26 16:07:45.511: 00:13:c3:e1:4c:e0 Discarding discovery request in LWAPP from AP supporting CAPWAP
*spamApTask7: Jun 26 16:07:45.512: 00:13:c3:e1:4c:e0 Discovery Request from 10.0.1.232:20023
*spamApTask7: Jun 26 16:07:45.512: 00:13:c3:e1:4c:e0 Join Priority Processing status = 0, Incoming Ap's Priority 1, MaxLrads = 25, joined Aps =0
*spamApTask7: Jun 26 16:07:45.512: 00:13:c3:e1:4c:e0 Discovery Response sent to 10.0.1.232:20023
*spamApTask4: Jun 26 16:07:46.516: 00:3a:99:db:fa:10 DTLS connection not found, creating new connection for 10:0:0:101 (55079) 10:0:1:45 (5246)
*spamApTask4: Jun 26 16:07:46.708: 00:3a:99:db:fa:10 DTLS connection closed event receivedserver (10:0:1:45/5246) client (10:0:0:101/55079)
*spamApTask4: Jun 26 16:07:46.708: 00:3a:99:db:fa:10 No entry exists for AP (10:0:0:101/55079)
*spamApTask4: Jun 26 16:07:46.708: 00:3a:99:db:fa:10 No entry exists in database
*spamApTask4: Jun 26 16:07:47.759: 00:3a:99:db:fa:a0 Discovery Request from 10.0.0.184:55084
*spamApTask4: Jun 26 16:07:47.759: 00:3a:99:db:fa:a0 Join Priority Processing status = 0, Incoming Ap's Priority 1, MaxLrads = 25, joined Aps =0
*spamApTask0: Jun 26 16:07:47.760: 00:3a:99:db:fa:a0 Received LWAPP DISCOVERY REQUEST to e8:b7:48:9b:86:4f on port '13'
*spamApTask0: Jun 26 16:07:47.760: 00:3a:99:db:fa:a0 Discarding discovery request in LWAPP from AP supporting CAPWAP
*spamApTask4: Jun 26 16:07:47.760: 00:3a:99:db:fa:a0 Discovery Response sent to 10.0.0.184:55084
*spamApTask4: Jun 26 16:07:47.760: 00:3a:99:db:fa:a0 Discovery Request from 10.0.0.184:55084
*spamApTask4: Jun 26 16:07:47.760: 00:3a:99:db:fa:a0 Join Priority Processing status = 0, Incoming Ap's Priority 1, MaxLrads = 25, joined Aps =0
*spamApTask4: Jun 26 16:07:47.760: 00:3a:99:db:fa:a0 Discovery Response sent to 10.0.0.184:55084
*spamApTask7: Jun 26 16:07:49.471: 00:13:c3:e1:4d:c0 Discovery Request from 10.0.1.239:20032
*spamApTask7: Jun 26 16:07:49.471: 00:13:c3:e1:4d:c0 Join Priority Processing status = 0, Incoming Ap's Priority 1, MaxLrads = 25, joined Aps =0
*spamApTask7: Jun 26 16:07:49.471: 00:13:c3:e1:4d:c0 Discovery Response sent to 10.0.1.239:20032
*spamApTask0: Jun 26 16:07:49.471: 00:13:c3:e1:4d:c0 Received LWAPP DISCOVERY REQUEST to e8:b7:48:9b:86:4f on port '13'
*spamApTask0: Jun 26 16:07:49.471: 00:13:c3:e1:4d:c0 Discarding discovery request in LWAPP from AP supporting CAPWAP
*spamApTask7: Jun 26 16:07:49.472: 00:13:c3:e1:4d:c0 Discovery Request from 10.0.1.239:20032
*spamApTask7: Jun 26 16:07:49.472: 00:13:c3:e1:4d:c0 Join Priority Processing status = 0, Incoming Ap's Priority 1, MaxLrads = 25, joined Aps =0
*spamApTask7: Jun 26 16:07:49.472: 00:13:c3:e1:4d:c0 Discovery Response sent to 10.0.1.239:20032
*spamApTask1: Jun 26 16:07:52.222: 00:13:c3:e1:4d:80 Discovery Request from 10.0.1.230:20027
*spamApTask1: Jun 26 16:07:52.222: 00:13:c3:e1:4d:80 Join Priority Processing status = 0, Incoming Ap's Priority 1, MaxLrads = 25, joined Aps =0
*spamApTask1: Jun 26 16:07:52.223: 00:13:c3:e1:4d:80 Discovery Response sent to 10.0.1.230:20027
*spamApTask0: Jun 26 16:07:52.223: 00:13:c3:e1:4d:80 Received LWAPP DISCOVERY REQUEST to e8:b7:48:9b:86:4f on port '13'
*spamApTask0: Jun 26 16:07:52.223: 00:13:c3:e1:4d:80 Discarding discovery request in LWAPP from AP supporting CAPWAP
*spamApTask1: Jun 26 16:07:52.223: 00:13:c3:e1:4d:80 Discovery Request from 10.0.1.230:20027
*spamApTask1: Jun 26 16:07:52.223: 00:13:c3:e1:4d:80 Join Priority Processing status = 0, Incoming Ap's Priority 1, MaxLrads = 25, joined Aps =0
*spamApTask1: Jun 26 16:07:52.224: 00:13:c3:e1:4d:80 Discovery Response sent to 10.0.1.230:20027
*spamApTask5: Jun 26 16:07:52.267: 00:3a:99:da:c7:70 DTLS connection not found, creating new connection for 10:0:0:181 (34152) 10:0:1:45 (5246)
*spamApTask1: Jun 26 16:07:52.274: 00:3a:99:db:ff:20 Discovery Request from 10.0.0.182:55099
*spamApTask1: Jun 26 16:07:52.274: 00:3a:99:db:ff:20 Join Priority Processing status = 0, Incoming Ap's Priority 1, MaxLrads = 25, joined Aps =0
*spamApTask0: Jun 26 16:07:52.274: 00:3a:99:db:ff:20 Received LWAPP DISCOVERY REQUEST to e8:b7:48:9b:86:4f on port '13'
*spamApTask1: Jun 26 16:07:52.274: 00:3a:99:db:ff:20 Discovery Response sent to 10.0.0.182:55099
*spamApTask0: Jun 26 16:07:52.274: 00:3a:99:db:ff:20 Discarding discovery request in LWAPP from AP supporting CAPWAP
*spamApTask1: Jun 26 16:07:52.275: 00:3a:99:db:ff:20 Discovery Request from 10.0.0.182:55099
*spamApTask1: Jun 26 16:07:52.275: 00:3a:99:db:ff:20 Join Priority Processing status = 0, Incoming Ap's Priority 1, MaxLrads = 25, joined Aps =0
*spamApTask1: Jun 26 16:07:52.275: 00:3a:99:db:ff:20 Discovery Response sent to 10.0.0.182:55099
*spamApTask1: Jun 26 16:07:52.306: 00:3a:99:db:f2:40 DTLS connection not found, creating new connection for 10:0:0:100 (55069) 10:0:1:45 (5246)
*spamApTask5: Jun 26 16:07:52.463: 00:3a:99:da:c7:70 DTLS connection closed event receivedserver (10:0:1:45/5246) client (10:0:0:181/34152)
*spamApTask5: Jun 26 16:07:52.463: 00:3a:99:da:c7:70 No entry exists for AP (10:0:0:181/34152)
*spamApTask5: Jun 26 16:07:52.463: 00:3a:99:da:c7:70 No entry exists in database
*spamApTask1: Jun 26 16:07:52.501: 00:3a:99:db:f2:40 DTLS connection closed event receivedserver (10:0:1:45/5246) client (10:0:0:100/55069)
*spamApTask1: Jun 26 16:07:52.502: 00:3a:99:db:f2:40 No entry exists for AP (10:0:0:100/55069)
*spamApTask1: Jun 26 16:07:52.502: 00:3a:99:db:f2:40 No entry exists in databaseSomething "weird" is on the newest 7.0.X. Here's my situation:
1. It doesn't happen to all new APs. When I mean "new", I mean out from a box including APs from RMA.
2. I've seen this in 1240, 1250, 1140. Haven't seen it on a 3500.
3. Here's how it goes ... When the AP, fresh from a box, connects to the networks, sees the WLC/WiSM and downloads the full IOS (OK so far). After the reboot the AP in question loads the new IOS and shows up in the WLC/WiSM. When I check CDP neighbors, NOTHING. What the ... ?
4. Go to the switch and do command "sh cdp neighbor" and what do I get? NOTHING.
5. Check PoE and show that it's IEEE.
For unknown reason, APs in this "trance" shuts off the CDP. I currently have a Cisco TAC Case trying to iron out this "feature". Doesn't appear on the 7.0.96.0 but happens to the newer one. -
1130AG not joining controller - FAILED CRYPTO INIT
I am trying to join my 1130AG-E-K9 AP to my 2016 WLC, but it is stuck in a boot loop and will not connect to the controller. The error I'm getting is:
*Mar 1 00:00:29.584: %CAPWAP-3-ERRORLOG: Could Not resolve CISCO-CAPWAP-CONTROLLER
*Mar 1 00:00:29.585: %CAPWAP-5-CHANGED: CAPWAP changed state to DISCOVERY
*Mar 1 00:00:29.598: %LWAPP-3-CLIENTERRORLOG: LWAPP Crypto Init (SSC): no certs in the SSC Private File
*Mar 1 00:00:29.598: %LWAPP-3-CLIENTERRORLOG: LWAPP Crypto Init: could not start PKI session
*Mar 1 00:00:29.598: %LWAPP-3-CLIENTERRORLOG: Failed to initialize Crypto. Rebooting
*Mar 1 00:00:29.663: %SYS-4-PUPDATECLOCK: Periodic Clock update with ROMMON failed, because size left in ROMMON (4294967295), size needed (29), error code (-1)
*Mar 1 00:00:29.663: %SYS-5-RELOAD: Reload requested by CAPWAP CLIENT. Reload Reason: FAILED CRYPTO INIT.
*Mar 1 00:00:29.664: %LWAPP-5-CHANGED: CAPWAP changed state to DOWNXmodem file system is available.
I found some details here: http://www.cisco.com/en/US/products/ps6366/products_tech_note09186a00808f8599.shtml, but I'm not sure what it means that I have a 'SSC AP'. I am not local to this AP, though I do have a console connection to it-what do I need to do to get it working again? It just continually goes through this error and reboots every 30 seconds or so, so it's useless at the moment.
Thanks!While that did help me potentially debug the AP, it seems the AP can not/is not reaching the WLC. Debugs on the WLC show other APs talking to it, but the only signature I'm picking up on the WLC from this AP is:
*Aug 08 20:34:36.376: 00:13:5f:fb:b4:f0 Echo Request from 10.50.0.25:44194
*Aug 08 20:34:36.376: 00:13:5f:fb:b4:f0 Echo Response sent to 10.50.0.25:44194
And from the AP itself:
Translating "CISCO-LWAPP-CONTROLLER"...domain server (255.255.255.255)
*Mar 1 00:00:06.475: %LWAPP-3-CLIENTEVENTLOG: Read and initialized AP event (contains, 1024 messages)
*Mar 1 00:00:08.523: %LINK-3-UPDOWN: Interface FastEthernet0, changed state up
*Mar 1 00:00:08.548: %SYS-5-RESTART: System restarted --
Cisco IOS Software, C1130 Software (C1130-RCVK9W8-M), Version 12.4(21a)JA2, RASE SOFTWARE (fc1)
Technical Support: http://www.cisco.com/techsupport
Copyright (c) 1986-2009 by Cisco Systems, Inc.
Compiled Mon 02-Nov-09 18:17 by prod_rel_team
*Mar 1 00:00:09.523: %LINEPROTO-5-UPDOWN: Line protocol on Interface FastEthet0, changed state to down
*Mar 1 00:00:17.310: %LINEPROTO-5-UPDOWN: Line protocol on Interface FastEthet0, changed state to up
Translating "CISCO-CAPWAP-CONTROLLER"...domain server (255.255.255.255)
*Mar 1 00:00:20.591: %CAPWAP-3-ERRORLOG: Could Not resolve CISCO-LWAPP-CONTRER
Writing out the event log to nvram...
*Mar 1 00:00:29.591: %CAPWAP-3-ERRORLOG: Could Not resolve CISCO-CAPWAP-CONTLER
*Mar 1 00:00:29.592: %CAPWAP-5-CHANGED: CAPWAP changed state to DISCOVERY
*Mar 1 00:00:29.605: %LWAPP-3-CLIENTERRORLOG: LWAPP Crypto Init (SSC): no ce in the SSC Private File
*Mar 1 00:00:29.605: %LWAPP-3-CLIENTERRORLOG: LWAPP Crypto Init: could not st PKI session
*Mar 1 00:00:29.605: %LWAPP-3-CLIENTERRORLOG: Failed to initialize Crypto. Roting
*Mar 1 00:00:29.666: %SYS-4-PUPDATECLOCK: Periodic Clock update with ROMMON led, because size left in ROMMON (4294967295), size needed (29), error code (
*Mar 1 00:00:29.667: %SYS-5-RELOAD: Reload requested by CAPWAP CLIENT. Reloaeason: FAILED CRYPTO INIT.
*Mar 1 00:00:29.667: %LWAPP-5-CHANGED: CAPWAP changed state to DOWN
Is my only option at this point reverting back to a standalone image, then going back to a LW one?
Thanks again,
-Ryan
Maybe you are looking for
-
Need advice on restoring from TimeMachine after new harddrive install
I will be installing a larger hard drive in my MacBook Pro tomorrow. I have Time Machine backup on on an external drive. I would appreciate any tips on restoring once I get the new 500gb drive installed. I also have a full drag and drop backup on ano
-
How much RAM & CPU should I allocate for Windows 7 Ultimate?
I am in the process of setting up my new 27" iMac i7. I'm brand new to Apple computers so this is a learning curve for me! I have installed Parallels Desktop 5 so I can run Windows 7 side by side with Snow Leopard. Now I am trying to install Windows
-
Urgent : problem while migrating from forms 6i to 9i
We are trying to upgrade forms 6i to forms 9i. One of our forms is using the host command to call a shell script . This command worked successfully in the form when it was in character mode in forms 6i. But we are facing problems while deploying it o
-
SAP Interface to PathGuide Latitude WMS
Hi All, Has anyone ever have experience of interfacing to this Warehouse Management System software using SAP? If so, what ABAP technology are we talking about? BAPI? Flat file? Even IDocs? etc Thanks, Niall Message was edited by: Niall F
-
I'm not sure if this is an iPhoto 6 problem or a problem originating from my inexperience with Photoshop Elements 4. I've scanned some old B&W family images at 300dpi; tidied them up using Elements 4's healing tool, and imported them into iPhoto. The