Cisco AIR-LAP1041N-E-K9 not working with WLC 4402 version 7.0.116.0

Hi All,
appreciate your support for a problem i started facing today. i have a Cisco WLC 4402 running version 7.0.116.0 and it is working great with 25 Cisco 1252 APs. we have recieved a new 20 Cisco 1041N APs today and i installed one in our site but it doesn't work. it worked fine and loaded the image from flash and got the WLC ip address through DHCP option and started showing the below error:
*Mar  1 00:00:10.021: %SOAP_FIPS-2-SELF_TEST_IOS_SUCCESS: IOS crypto FIPS self test passed
*Mar  1 00:00:10.033: *** CRASH_LOG = YES
*Mar  1 00:00:10.333: Port 1 is not presentSecurity Core found.
Base Ethernet MAC address: C8:9C:1D:53:57:5E
*Mar  1 00:00:11.373: %SOAP_FIPS-2-SELF_TEST_RAD_SUCCESS: RADIO crypto FIPS self test passed on interface Dot11Radio 0
*Mar  1 00:00:11.465: %LWAPP-3-CLIENTEVENTLOG: Read and initialized AP event log (contains, 1088 messages)
*Mar  1 00:00:11.494:  status of voice_diag_test from WLC is false
*Mar  1 00:00:12.526: %LINK-3-UPDOWN: Interface GigabitEthernet0, changed state to up
*Mar  1 00:00:13.594: %LINEPROTO-5-UPDOWN: Line protocol on Interface GigabitEthernet0, changed state to up
*Mar  1 00:00:13.647: %SYS-5-RESTART: System restarted --
Cisco IOS Software, C1040 Software (C1140-K9W8-M), Version 12.4(23c)JA2, RELEASE SOFTWARE (fc3)
Technical Support: http://www.cisco.com/techsupport
Copyright (c) 1986-2011 by Cisco Systems, Inc.
Compiled Wed 13-Apr-11 12:50 by prod_rel_team
*Mar  1 00:00:13.647: %SNMP-5-COLDSTART: SNMP agent on host APc89c.1d53.575e is undergoing a cold start
*Mar  1 00:08:59.062: %CAPWAP-5-CHANGED: CAPWAP changed state to DISCOVERY
*Mar  1 00:08:59.062: bsnInitRcbSlot: slot 1 has NO radio
*Mar  1 00:08:59.138: %LINK-5-CHANGED: Interface Dot11Radio0, changed state to reset
*Mar  1 00:08:59.837: %SSH-5-ENABLED: SSH 2.0 has been enabled
*Mar  1 00:09:00.145: %LINEPROTO-5-UPDOWN: Line protocol on Interface Dot11Radio0, changed state to down
*Mar  1 00:09:09.136: %DHCP-6-ADDRESS_ASSIGN: Interface GigabitEthernet0 assigned DHCP address 172.16.26.81, mask 255.255.255.0, hostname APc89c.1d53.575e
*Mar  1 00:09:17.912: %PARSER-4-BADCFG: Unexpected end of configuration file.
*Mar  1 00:09:17.912:  status of voice_diag_test from WLC is false
*Mar  1 00:09:17.984: Logging LWAPP message to 255.255.255.255.
*Mar  1 00:09:19.865: %CDP_PD-4-POWER_OK: Full power - NEGOTIATED inline power source
*Mar  1 00:09:19.886: %LINK-3-UPDOWN: Interface Dot11Radio0, changed state to up
*Mar  1 00:09:20.873: %LINEPROTO-5-UPDOWN: Line protocol on Interface Dot11Radio0, changed state to up
*Mar  1 00:09:20.874: %SYS-6-LOGGINGHOST_STARTSTOP: Logging to host 255.255.255.255 started - CLI initiated
Translating "CISCO-CAPWAP-CONTROLLER.atheertele.com"...domain server (172.16.40.240)
*Mar  1 00:09:29.029: %CAPWAP-5-DHCP_OPTION_43: Controller address 172.16.100.102 obtained through DHCP
*May 25 08:27:02.000: %CAPWAP-5-DTLSREQSEND: DTLS connection request sent peer_ip: 172.16.100.101 peer_port: 5246
*May 25 08:27:02.001: %CAPWAP-5-CHANGED: CAPWAP changed state to
*May 25 08:27:03.175: %CAPWAP-5-DTLSREQSUCC: DTLS connection created sucessfully peer_ip: 172.16.100.101 peer_port: 5246
*May 25 08:27:03.177: %CAPWAP-5-SENDJOIN: sending Join Request to 172.16.100.101
*May 25 08:27:03.177: %CAPWAP-5-CHANGED: CAPWAP changed state to JOIN
*May 25 08:27:03.329: %CAPWAP-5-CHANGED: CAPWAP changed state to CFG
*May 25 08:27:03.333: %DTLS-5-ALERT: Received WARNING : Close notify alert from 172.16.100.101
*May 25 08:27:03.333: %DTLS-5-PEER_DISCONNECT: Peer 172.16.100.101 has closed connection.
*May 25 08:27:03.333: %DTLS-5-SEND_ALERT: Send FATAL : Close notify Alert to 172.16.100.101:5246
*May 25 08:27:03.378: %CAPWAP-5-CHANGED: CAPWAP changed state to DISCOVERY
*May 25 08:27:03.378: %CAPWAP-5-CHANGED: CAPWAP changed state to DISCOVERY
*May 25 08:27:03.378: bsnInitRcbSlot: slot 1 has NO radio
*May 25 08:27:03.448:  status of voice_diag_test from WLC is false
*May 25 08:27:14.000: %CAPWAP-5-DTLSREQSEND: DTLS connection request sent peer_ip: 172.16.100.101 peer_port: 5246
*May 25 08:27:14.001: %CAPWAP-5-CHANGED: CAPWAP changed state to
*May 25 08:27:15.185: %CAPWAP-5-DTLSREQSUCC: DTLS connection created sucessfully peer_ip: 172.16.100.101 peer_port: 5246
*May 25 08:27:15.186: %CAPWAP-5-SENDJOIN: sending Join Request to 172.16.100.101
*May 25 08:27:15.186: %CAPWAP-5-CHANGED: CAPWAP changed state to JOIN
*May 25 08:27:15.330: %CAPWAP-5-CHANGED: CAPWAP changed state to CFG
*May 25 08:27:15.333: %DTLS-5-ALERT: Received WARNING : Close notify alert from 172.16.100.101
*May 25 08:27:15.334: %DTLS-5-PEER_DISCONNECT: Peer 172.16.100.101 has closed connection.
*May 25 08:27:15.334: %DTLS-5-SEND_ALERT: Send FATAL : Close notify Alert to 172.16.100.101:5246
*May 25 08:27:15.379: %CAPWAP-5-CHANGED: CAPWAP changed state to DISCOVERY
*May 25 08:27:15.379: %CAPWAP-5-CHANGED: CAPWAP changed state to DISCOVERY
*May 25 08:27:15.379: bsnInitRcbSlot: slot 1 has NO radio
*May 25 08:27:15.450:  status of voice_diag_test from WLC is false
*May 25 08:27:26.000: %CAPWAP-5-DTLSREQSEND: DTLS connection request sent peer_ip: 172.16.100.101 peer_port: 5246
*May 25 08:27:26.001: %CAPWAP-5-CHANGED: CAPWAP changed state to
*May 25 08:27:27.182: %CAPWAP-5-DTLSREQSUCC: DTLS connection created sucessfully peer_ip: 172.16.100.101 peer_port: 5246
*May 25 08:27:27.183: %CAPWAP-5-SENDJOIN: sending Join Request to 172.16.100.101
*May 25 08:27:27.184: %CAPWAP-5-CHANGED: CAPWAP changed state to JOIN
*May 25 08:27:27.329: %CAPWAP-5-CHANGED: CAPWAP changed state to CFG
*May 25 08:27:27.333: %DTLS-5-ALERT: Received WARNING : Close notify alert from 172.16.100.101
*May 25 08:27:27.333: %DTLS-5-PEER_DISCONNECT: Peer 172.16.100.101 has closed connection.
*May 25 08:27:27.333: %DTLS-5-SEND_ALERT: Send FATAL : Close notify Alert to 172.16.100.101:5246
*May 25 08:27:27.377: %CAPWAP-5-CHANGED: CAPWAP changed state to DISCOVERY
*May 25 08:27:27.377: %CAPWAP-5-CHANGED: CAPWAP changed state to DISCOVERY
*May 25 08:27:27.377: bsnInitRcbSlot: slot 1 has NO radio
*May 25 08:27:27.433: %LINK-5-CHANGED: Interface Dot11Radio0, changed state to administratively down
*May 25 08:27:27.446: %PARSER-4-BADCFG: Unexpected end of configuration file.
*May 25 08:27:27.447:  status of voice_diag_test from WLC is false
*May 25 08:27:27.448: %LINK-3-UPDOWN: Interface Dot11Radio0, changed state to up
*May 25 08:27:27.456: %LINK-5-CHANGED: Interface Dot11Radio0, changed state to reset
*May 25 08:27:38.000: %CAPWAP-5-DTLSREQSEND: DTLS connection request sent peer_ip: 172.16.100.101 peer_port: 5246
*May 25 08:27:38.001: %CAPWAP-5-CHANGED: CAPWAP changed state to
*May 25 08:27:39.183: %CAPWAP-5-DTLSREQSUCC: DTLS connection created sucessfully peer_ip: 172.16.100.101 peer_port: 5246
*May 25 08:27:39.184: %CAPWAP-5-SENDJOIN: sending Join Request to 172.16.100.101
*May 25 08:27:39.184: %CAPWAP-5-CHANGED: CAPWAP changed state to JOIN
*May 25 08:27:39.326: %CAPWAP-5-CHANGED: CAPWAP changed state to CFG
*May 25 08:27:39.329: %DTLS-5-ALERT: Received WARNING : Close notify alert from 172.16.100.101
*May 25 08:27:39.329: %DTLS-5-PEER_DISCONNECT: Peer 172.16.100.101 has closed connection.
*May 25 08:27:39.330: %DTLS-5-SEND_ALERT: Send FATAL : Close notify Alert to 172.16.100.101:5246
*May 25 08:27:39.375: %CAPWAP-5-CHANGED: CAPWAP changed state to DISCOVERY
*May 25 08:27:39.375: %CAPWAP-5-CHANGED: CAPWAP changed state to DISCOVERY
*May 25 08:27:39.375: bsnInitRcbSlot: slot 1 has NO radio
*May 25 08:27:39.446:  status of voice_diag_test from WLC is false
*May 25 08:27:49.000: %CAPWAP-5-DTLSREQSEND: DTLS connection request sent peer_ip: 172.16.100.101 peer_port: 5246
*May 25 08:27:49.001: %CAPWAP-5-CHANGED: CAPWAP changed state to
*May 25 08:27:50.179: %CAPWAP-5-DTLSREQSUCC: DTLS connection created sucessfully peer_ip: 172.16.100.101 peer_port: 5246
*May 25 08:27:50.180: %CAPWAP-5-SENDJOIN: sending Join Request to 172.16.100.101
*May 25 08:27:50.180: %CAPWAP-5-CHANGED: CAPWAP changed state to JOIN
*May 25 08:27:50.323: %CAPWAP-5-CHANGED: CAPWAP changed state to CFG
*May 25 08:27:50.326: %DTLS-5-ALERT: Received WARNING : Close notify alert from 172.16.100.101
*May 25 08:27:50.326: %DTLS-5-PEER_DISCONNECT: Peer 172.16.100.101 has closed connection.
*May 25 08:27:50.326: %DTLS-5-SEND_ALERT: Send FATAL : Close notify Alert to 172.16.100.101:5246
*May 25 08:27:50.370: %CAPWAP-5-CHANGED: CAPWAP changed state to DISCOVERY
*May 25 08:27:50.370: %CAPWAP-5-CHANGED: CAPWAP changed state to DISCOVERY
*May 25 08:27:50.370: bsnInitRcbSlot: slot 1 has NO radio
*May 25 08:27:50.425: %LINK-5-CHANGED: Interface Dot11Radio0, changed state to administratively down
*May 25 08:27:50.438: %PARSER-4-BADCFG: Unexpected end of configuration file.
i searched for the regulatory domains difference between  AIR-LAP1041N-E-K9 and  AIR-LAP1041N-A-K9 and didn't find any difference that may affect the operation of this AP.
just to mention that our configuration in WLC for regulatory domains is:
Configured Country Code(s) AR 
Regulatory Domain  802.11a:  -A
                             802.11bg: -A
My question is, should i only include my country in the WLC (IQ) to add the requlatry domain (-E) to solve this problem? or changing the country will affect the operation of all working APs??
Appreciate your kind support,
Wisam Q.

Hi Ramon,
thank you for the reply but as shown in the below link:
http://www.cisco.com/en/US/docs/wireless/controller/release/notes/crn7.0.html#wp233793
the WLC in version 7.0.116.0 supports Cisco 1040 seiries APs.
Thanks,
Wisam Q.

Similar Messages

  • I have laptop with digital persona (finger scanning) to automatic feed the passwords. it was working properly with the older version of firefox but is not working with the latest version of the firefox. why? give me a solution.

    i have laptop with digital persona (finger scanning) to automatic feed the passwords. it was working properly with the older version of firefox but is not working with the latest version of the firefox. why? give me a solution.

    Please authorize ADE 3 with same credentials that you used with older version of ADE

  • 10g JSpell PJC does not work with latest JSpell version

    Looks like latest (10g) forms demo - Spell check with JSpell does not work with the latest version of the JSpell software (does not look like this demo been changed from the previous version).
    Does anybody has a success running this or have any suggestions how to integrate it together?
    Thanks for any input.

    We're in contact with JSpell on this issue and will revise the integration code as soon as we recieve the relevant updates from them.

  • A website that i use quite frequently will not work with the newer versions of firefox. Is there a compatability mode of some way to get the newer version to work?

    All the website says is this browser is not supported. Only version 3.5 is. I can list the url because it is a work url

    You can install the portable Firefox 3.6.x version to access websites that do not work with Firefox 5+.
    *http://portableapps.com/apps/internet/firefox_portable#legacy
    *http://portableapps.com/apps/internet/firefox_portable/localization#legacy36

  • I'm big fan of Google Toolbar but is does not work with the latest version of Firefox??

    I made an update yesterday and all of a sudden the Google Toolbar did not match with the latest version of Firefox...??
    Will that be solve or is my time with Firefox over???

    whatever you are trying for me to see, it blips up on my screen for a half a second and then it goes immediately to the reply page, can you type out or cut and past the entire link or tell me the title of what the post or article is? This is even worse, Firefox doesn't work within Firefox!! now that is sad

  • Before I downloaded the latest version of Firefox I could us the Norton Idnetity Safe. It will not work with the new version. What do I have to do to make it work?

    I am not sure if this is a plugin or extension. All I know is that it worked with the old version of Firefox. It is very important to me to be able to use this feature. Any help would be appreciated.

    THIS ISSUE IS RESOLVED FOR ME.
    When I opened this pop-up to view the settings (File > Page Setup > "Format & Options": Scale ), the Scale value was 40%. Changing it to 100% corrected the issue I observed.
    To my knowledge, I have not been inside this pop-up window before to set the Scale option. Could this value be affected by other actions within Firefox? I noticed this while using v12 which was installed 24Apr2012.I know it worked correctly since that installation, so why did the Scale value change?
    UPDATE: I just realized that the Scale option in print preview sets the Scale value in the settings. NOTE TO ALL: This is a sticky setting, not just a setting for a specific output request.

  • Cisco css http keepalive is not working with GET command

    Dear all
    i have Cisco Css connected to Dell Server (via switch)
    Cisco CSS - 192.168.1.3 and Dell Server - 192.168.1.5
    Dell server is setup with windows 2009R2 and Apache HTTPD is version 2.2
    This server is dedicated to host multiple doamins with Apache lik
    www.abc.co.uk
    www.xyz.co.uk
    Now the clinet wants to setup the http keepalive  with specfic web page like /testpage.html  for all these domains. i have teseed with single URI. it is working the comamnds are
    config)# service serv1
    (config-service[serv1])# ip address 192.168.1.5
    (config-service[serv1])# keepalive type http
    (config-service[serv1])# keepalive method head    ( get i have not used due to hash mismatch with apche server, if i use GET it is not working)
    (config-service[serv1])# keepalive uri "/testpage.html"
    (config-service[serv1])# active
    It is working with single URI.  but how can i do the same thing for multiple doamins ?
    for multiple doamins do i need use script ? or can i use with commands ?
    if i need to use script the script is
    !no echo
    ! Filename: httptag-test
    ! Parameters: HostName WebPage HostTag
    ! Description:
    !       This script will connect to the remote host and do an HTTP
    !   GET method upon the web page that the user has asked for.
    !   This script also adds a host tag to the GET request.
    ! Failure Upon:
    !   1. Not establishing a connection with the host.
    !       2. Not receiving an HTTP status "200 OK"
    if ${ARGS}[#] "NEQ" "3"
            echo "Usage: httptag-test \'Hostname WebPage HostTag\'"
            exit script 1
    endbranch
    ! Defines:
    set HostName "${ARGS}[1]"
    set WebPage "${ARGS}[2]"
    set HostTag "${ARGS}[3]"
    ! Connect to the remote Host
    set EXIT_MSG "Connection Failure"
    socket connect host ${HostName} port 80 tcp
    ! Send the GET request for the web page
    set EXIT_MSG "Send: Failed"
    socket send ${SOCKET} "GET ${WebPage} HTTP/1.1\nHost: ${HostTag}\n\n"
    ! Send the HEAD request for the web page
    set EXIT_MSG "Send: Failed"
    socket send ${SOCKET} "HEAD ${WebPage} HTTP/1.1\nHost: ${HostTag}\n\n"
    ! Wait for a good status code
    set EXIT_MSG "Waitfor: Failed"
    socket waitfor ${SOCKET} "200 OK"
    no set EXIT_MSG
    socket disconnect ${SOCKET}sh w
    exit script 0
    in the script i have not used GET becasue, when CSS send GET request to apache it use hash, but apache is not able to respond with same hash and it shows that website is down. more information- click below url
    http://www.cisco.com/en/US/docs/app_ntwk_services/data_center_app_services/css11500series/v7.40/command/reference/CmdKeepC.html#wp1139668
    (config-keepalive) method
    I have uploaded in CSS with httptag-test file and applied these commands
    service comp.brit.co.uk-80
      keepalive port 80
      ip address 192.168.1.5
      keepalive frequency 10
    keepalive maxfailure 2
    keepalive retryperiod 10
    keepalive type script httptag-test "192.168.1.5 /testpage.html  www.abc.co.uk
    keepalive type script httptag-test "192.168.1.5 /testpage.html  www.xyz.co.uk
    but this script is not working
    my question is:
    1.do i need use script only to setup http keepalvie with webpage for multiple domains ?
    2.with out using script is there any solution like CICSCO  CSS commands  to setup http uril for multiple domains which are on 1 singl server.
    please help me asap

    Hello Muhammad,
    If you wish to use multiple domains for a URI  keep-alive check, and perform a HEAD request what Daniel mentioned is  correct.  You have to use a scripted keep-alive check on the service.  However, you should not use the default "ap-kal-httptag" script to do so  as it's limited to only 1 website (unless you modify the script).  You're best bet would be using the "ap-kal-httplist" script on the CSS  as it allows the checking of 2 different websites along with a webpage  to check for each site using HTTP HEAD method.
    !no echo
    ! Filename: ap-kal-httplist
    ! Parameters: Site1 WebPage1 Site2 WebPage2 [...]
    ! Description:
    !    This script will connect a list of sites/webpage pairs.  The
    !   user must simply supply the site, and then the webpage and
    !   we'll attempt to do an HTTP HEAD on that page.
    ! Failure Upon:
    !   1. Not establishing a connection with the host.
    !   2. Not receiving a status code 200 on the HEAD request on any
    !      one site.  If one fails, the script fails.
    ! Make sure the user has a qualified number of arguments
    if ${ARGS}[#] "LT" "2"
            echo "Usage: ap-kal-httplist \'WebSite1 WebPage1 WebSite2 WebPage2 ...'"
            exit script 1
    endbranch
    while ${ARGS}[#] "GT" "0"
            set Site "${ARGS}[1]"
        var-shift ARGS
        if ${ARGS}[#] "==" "0"
            set EXIT_MSG "Parameter mismatch: hostname present but webpage was not"
            exit script 1
        endbranch
        set Page "${ARGS}[1]"
        var-shift ARGS
        no set EXIT_MSG
        function HeadUrl call "${Site} ${Page}"
    endbranch
    exit script 0
    function HeadUrl begin
    ! Connect to the remote Host
    set EXIT_MSG "Connect: Failed to connect to ${ARGS}[1]"
    socket connect host ${ARGS}[1] port 80 tcp 2000
    ! Send the head request
    set EXIT_MSG "Send: Failed to send to ${ARGS}[1]"
    socket send ${SOCKET} "HEAD ${ARGS}[2] HTTP/1.0\n\n"
    ! Wait for the status code 200 to be given to us
    set EXIT_MSG "Waitfor: Failed to wait for '200' on ${ARGS}[1]"
    socket waitfor ${SOCKET} " 200 " 2000
    no set EXIT_MSG
    socket disconnect ${SOCKET}
    function HeadUrl end
    Rather  then modify the default "ap-kal-httplist" script on the CSS I would  simply define the arguments within the service configuration itself.   Something like the following (using your service example):
    service dell-192.168.1.5
    ip address 192.168.1.5
    keepalive type script ap-kal-httplist "www.abc.co.uk /testpage.html www.xyz.co.uk /testpage.html"
    active
    As  long as the server is configured to reply to host headers, and the page  is configured to retuen a "200 OK" the above service configuration  should work. If there are any errors simply run "show service  " to view why there was a failure. If there is a  failure, and the output from the command specified shows a line number  run the following command against the script to view at what point  (line) did the failure occur:
    show script ap-kal-httplist line-numbers
    Hope this helps!
    - Jason Espino

  • Flash, Adobe Air, Time Machine, Safari not  working with Snow Leopard

    Really need some help with this.
    Did an archive and install of Leopard then installed Snow Leopard. No problems yet.
    90% of Video sites would not work. Uninstalled and reinstalled Flash. Uninstalled ShockWave, could not reinstall with 10.6.1.
    Attempt to install adobe air, received this message: "couldn't write the application to hard drive - please verify and try again." performed verify disk, disk permissions, repair permissions all ok.
    Attempted to install Air again, same message.
    Tried to use Time Machine to open Safari from a week ago, received message: I did not have permission.
    Using Macbook Pro, 2g memory, 80g hd, with 42g free.
    Backed up on ext. HD,
    Oh, one more, getting a lot of spinning wheels when using Safari that causes a lockup and hard re-start.
    I have an expensive piece of software that uses adobe air and I create videos for my business and I'm not able to do so now.
    Can anyone give me any ideas what I can do.
    Thanks,
    Z

    After a couple of days of problems with Snow Leopard and flash, safari etc... I figured out the problem is with my account.
    I created a new admin account and everything seems to be working. Well almost.
    a couple of things I've noticed are right clicking on dock icons does nothing, no option to quit or keep in dock.
    Apple Techs', had me change my account months ago to fix a problem with safari crashing. It didn't really work and more problems resulted.
    *So now my big question is: How do I move need items over to the new account.* I don't want to move everything over as I might bring what caused the problem in the first place.
    What I need are several apps,(like ilife, iwork, firefox, devonthink, 1password etc.) downloads, desktop, docs, files, and book marks.
    *What is the best way for me to do this?* Is there anything I need to do re: Snow Leopard on the new account?
    I feel like I have a new and functioning Mac again just around the corner.
    Looking for your help, thanks,
    Z

  • WLC 2106_AP-1131_dell vostro 14 v3446 wifi not working with WLC

    Hi,
    I'm facing issue with newly purchased Dell laptops(dell vostro 14 v3446) are not able to join in WLC.
    I have check WLAN profile for these laptops ,all mapped correct,but laptops not able to join the same profile.
    Only one(newly purchased) laptop is working fine with WLC profile,remaining laptop all config is same but not getting connected with WLC. 
    Laptop wifi is working with another vendor APs.
    But this particular profile working with my exciting user's laptop perfectly.
    WLC/-AIR-WLC2106-K9-Firmware version—6.0.199.4
    AP-AIR-LAP1131AG-A-K9.
    Please advice me here to resolve this problem.
    regards,vijesh
    This was posted in lieu of blog https://supportforums.cisco.com/node/12292096  which was deleted since questions should be questions as discussions as not as blogs ;-) 

    Hi Leo,
    Thanks for your response.
    Client laptop trying to connect the SSID and once authentication key entered ,it will try for a while then error message come "could not connect...." 
    As our suggested,i will create new profile with open authentication,then try to connect the laptop.
    we have planned to upgrade WLC firmware in coming weekend.

  • My Labview Report generator is not working with 2013 excel version

    Hi All,
    My report generator tool kit which was developpend using labview 2011 was workign with excel 2010...after that i installed 2013 excel and the code is not working..
    Do i need to enable some setting to work with excel 2013.
    Basically this generator tool will copy the charts from excel and paste in power point...Please let me know.
    Thanks,
    Hareesh

    Ah, I understand now - I had assumed you were using the NI Toolkit.
    If you're not using the report generation toolkit, did you write your own VIs for communicating with Office or are you using a different toolkit? If you're using ActiveX to communicate with Office it may be that the ActiveX API has changed for Office 2013 - you will probably need to modify your program for the new calls.
    Since it wasn't as obvious as I thought with the report generation toolkit, it would help if you posted some code to try and understand what might be happening. Are you getting any errors in your application when you try to use Office 2013?
    Certified LabVIEW Architect, Certified TestStand Developer
    NI Days (and A&DF): 2010, 2011, 2013, 2014
    NI Week: 2012, 2014
    Knowledgeable in all things Giant Tetris and WebSockets

  • HP Protect tool password manager not working with the new version of Mozilla: I got this alert: "Firefox doesn't know how to open this address, because the protocol (dpql) isn't associated with any program." please help

    I have an HP ProBook 4520s. I have been using HP Protect tool's Password manager to store and manage my passords for all Login websites in Firefox 3.6. As a result, I just swiped my fingerprint to log on to any website.
    After I installed the version 4 of Firefox, my all my login details do not work anymore. I have tried to reset them but I repeatedly get this error: "Firefox doesn't know how to open this address, because the protocol (dpql) isn't associated with any program."
    something like this would have been passed onto the address: "dpql://c:\program%20files%20(x86)\hewlett-packard\hp%20protecttools%20security%20manager\bin\dpminionlineids.dll/qlinkload.htm#id=2".
    Although the password manager works with Internet Explorer 9, I need it to work with Firefox 4 as this is my preferred browser.
    Please help. Thank you!

    I guess this means that IE is more user friendly for HP Password Manager finger swipe recall of passwords, a favorite of mine. I still don't see a post from Firefox as to why they haven't produced fix. So I'll switch to IE until things change. I don't see value in downgrading to a Firefox version that's no longer going to be supported.

  • Automated Composite build/test not work with non-default version

    Hello,
    I have a BPEL composite and I am trying to setup maven and soapUI to build, deploy, test, and upon successful test, set it as the default version. The difficulty I am having is testing the composite before it becomes the default version. I am able to hit the endpoint using the full URL with the randomly generated ID in it using soapUI (see below), but not by using the shortened URL.
    Full URL: http://soabpm-vm:8001/soa-infra/services/default/Project1!0.0.12-SNAPSHOT*soa_13954572-b91f-480d-88d2-037e92083d72/bpelprocess1_client_ep
    Shortened URL: http://soabpm-vm:8001/soa-infra/services/default/Project1!0.0.12-SNAPSHOT/bpelprocess1_client_ep
    I tried hitting the shortened URL outside of the maven build, just using soapUI, and the response is empty. However, if I then mark this new version as default (through EM), and then mark a previous version as default (let's say 0.0.11), then the shortened URL for 0.0.12 can be successfully hit.
    It seems to me then that before the shortened URL above can be used, that specific version must have been set as the default version at some point. This would make an automated maven/soapUI test of new version (but not default) quite difficult, as it would have to somehow retrieve the full URL.
    Is this a bug or can it be fixed with a config setting change?
    Here are the steps in the process, maven build (using the Oracle provided ant sca files):
    1. Compile
    2. Package
    3. Deploy, not as default
    4. Test the new version (using soapUI plugin)
    5. If successful tests, mark new version as default
    The problem is with step 4, can't determine what the full URL is and the shortened URL does not work.
    Thanks
    Ben

    I found a similar issue in Oracle's support site, Patch 13774839 (based on bug 13569816). I will try that out and post the results here.

  • Juno does not work with the latest version of firefox Why?

    I would love to install the latest version of Firefox, but when I attempted to It indicated that It was not compatible with my Juno email service, why don't you guys ever include Juno when you do updates? Very frustrating as now my browser experience feels like my computer is dead. I finally gave up and installed Safari which is working at lightning speed. Don't suggest IE as I hate all Microsoft products,they are even worse at not testing things.

    whatever you are trying for me to see, it blips up on my screen for a half a second and then it goes immediately to the reply page, can you type out or cut and past the entire link or tell me the title of what the post or article is? This is even worse, Firefox doesn't work within Firefox!! now that is sad

  • Help,My vc2003 can not work with indesign debug version

    Hello everyone, I am a new developer of Indesign plugin, recently I got the problem as follows:
    I use vc2003 to open the SDK provided project, and click F5, then selected the Indesign as the programm to load this plug-in. However Indesign did not load the plugin and further more, non of the break-points I setted in the programm worked. It was very strange!
    Any one can help me? Thank you very much!

    Thank you very much for your reply!
    I had solved the problem.
    If you just put the plugin in the app's plugin folder, the VC2003 would be unable to work with your indesign.
    In order to debug my plugin with VC2003 and indesign, I edit the file in %Documents and Settings%\%user%\Application Data\Adobe\InDesign\Version 4.0 which named PlugInConfig, copy the PlugInConfig.out and renamed it as PlugInConfig.txt and Dlelte the content then add the following lines:
    =Path
    "your custome plugin folder".
    Problem solved!:)

  • The streamer (automatic updating) does not work with the last version

    the automatic updating of screens (streamers) do not work anymore with the new version. I use Windows sp3.

    the automatic updating of screens (streamers) do not work anymore with the new version. I use Windows sp3.

Maybe you are looking for

  • Lenovo G710 Battery not detected in Windows 8.1 64 bit

    Hi there, I have the Lenovo G710. I haven't used the battery for a while now and  I use the laptop by connecting the powerlead directly to mains power outlet.  I decided today to plug the battery in. The battery indicator lights up. Windows 8.1 does

  • Trying to restore Mail messages & folders

    Before doing a clean install of Leopard, I did a complete backup of my system. After restoring my data, I did not realize that I had a problem with Mail. Though many of my email messages are listed, I am missing all of the local sub-folders and their

  • Error with movie thumbnails in Library module

    Hello! I have a Nikon D7000 and I'm having problems with Lightroom's Library module: the preview of the movies doesn't work, I'm getting an error. I'm attaching a screenshot. Could this be fixed before Lightroom 3.4?

  • How to save a png with a straight or fat alpha?

    Long story short, work in broadcast and a new piece of gear prefers png files.  I know how to save png's with a transparency, that's not the problem.  What I don't know how to do or if it's possible is to save them with a straight or fat alpha.  Righ

  • Integration Server URL not being updated in SXMB_ADMIN

    I have changed an incorrect entry in the SLD for my business system for my XI installation (port was wrong).  When I go into SXMB_ADMIN --> Integration Engine --> Configuration --> Integration Engine Configuration The corresponding Integration Server