Cisco AP1121G Workgroup Bridge Problem

Hello,
For reference I have attached the following:
Network Diagram
Ping Results Table
Configurations for 1811 router, ap1121g root access point, ap1121g wgb.
I am seeking assistance with the following problem.
Referring to the attached network diagram, I cannot communicate past the ap1121g-wgb in either direction.
Also attached is a result table of ping attempts through the ap1121wgb from each side.
I don't have a problem with the wireless connections. The ap1121g's associate ok.
Based on the ping results the problem appears to be in the ap1121g-wgb configuration, but I have run out of ideas.
The following two cisco documents have been my main reference, besides the cisco command lookup site.
http://www.cisco.com/en/US/customer/products/hw/wireless/ps430/products_configuration_example09186a00805b9b87.shtml
http://www.cisco.com/en/US/docs/wireless/access_point/12.4_21a_JA1/configuration/guide/scg12421aJA1-chap19-wgb-standby.pdf
Any insight will be greatly appreciated.
Thanks...

Robert,
Going back to your original post and looking through the example given in the first URL, I spotted a few lines in the example configurations which apply to older revisions of code, but not newer AP code, so they may be misleading. Based on the parameter availability of station-role workgroup-bridge in your last message, would you be wiling to try the following?
Reset both 1121 APs to factory default configuration (#write erase -- do not save config to startup if prompted)
Give each AP an IP address on BVI1 so that both APs are in the same subnet
Apply the following configuration to the infrastrucuture (root) AP:
dot11 ssid WGB-SSID
authentication open
interface dot11radio 0
ssid WGB-SSID
station-role root
no shutdown
Apply the following configuration to the workgroup-bridge (client) AP:
dot11 ssid WGB-SSID
authentication open
interface dot11radio 0
ssid WGB-SSID
station-role workgroup-bridge
no shutdown
The intended goal with this exercise is to get rid of all config and to try only basic required elements of a WGB configuration, starting with fresh factory defaults. Let's see if it will work for you as a bare-bones setup and then you can add other configuration like encryption and ACLs back in later.
Justin

Similar Messages

1602 AP - Workgroup Bridge Cannot Associate to Parent AP

Hi All,
For a few weeks now, I have been trying to connect a Cisco 1602 standalone AP to our unified wireless network as a workgroup bridge. Eventually this AP is to be moved to another wireless network where I will need it to run in universal workgroup bridge mode (for non Cisco wireless networks), so I just want to get this working in the office before I take it elsewhere and try to get that to work, as the configuration will be similar.
So far I've been unable to get this 1602 AP to associate to our network. The particular SSID I'm trying to set up is a BYO style SSID, normally if you connect a device you provide your Active Directory username / password and your laptop / phone / whatever connects. I know the username is fine because if I use it on another device it's not a problem.
The AP keeps repeating this message: %DOT11-4-CANT_ASSOC: Interface Dot11Radio0, cannot associate: Associating. Cisco.com tells me that this is to do with MFP, however I've changed a number of MFP settings in the SSID and this seems to have made no difference.
I'm thinking this is a problem with authentication or association. I have a question, why do I need to input Radius server information into the config (eap_methods)? When you connect a regular device to this SSID it doesn't require any Radius server settings in order to connect, I don't understand why the AP needs these settings. Also, when authenticating to AD, do you need to include the domain name as part of the username?
Wireless isn't my strong point unfortunately. Is anyone able to help with this? Config and log is below. Many thanks.
version 15.2
no service pad
service timestamps debug datetime msec
service timestamps log datetime msec
service password-encryption
hostname WGB-AP
logging buffered 10000
logging rate-limit console 9
enable secret 5 xxxx
aaa new-model
aaa user profile userprofilename
aaa group server radius rad_eap
aaa group server radius rad_mac
aaa group server radius rad_acct
aaa group server radius rad_admin
aaa group server tacacs+ tac_admin
aaa group server radius rad_pmip
aaa group server radius dummy
aaa authentication login eap_methods group rad_eap
aaa authentication login mac_methods local
aaa authorization exec default local
aaa accounting network acct_methods start-stop group rad_acct
aaa session-id common
no ip routing
no ip cef
dot11 syslog
dot11 ssid BYO
authentication open eap eap_methods
authentication shared eap eap_methods
authentication network-eap eap_methods
authentication key-management wpa version 2
dot1x credentials MyCreds
dot1x eap profile EAPTLS
infrastructure-ssid
ids mfp client optional
eap profile EAPTLS
method mschapv2
method peap
crypto pki token default removal timeout 0
crypto pki trustpoint TP-self-signed-88743315
enrollment selfsigned
subject-name cn=IOS-Self-Signed-Certificate-88743315
revocation-check none
rsakeypair TP-self-signed-88743315
crypto pki trustpoint WGB-PEAP
enrollment terminal
subject-name CN=username
revocation-check none
rsakeypair manual-keys 1024
crypto pki certificate chain TP-self-signed-88743315
certificate self-signed 01
30820227 30820190 A0030201 02020101 300D0609 2A864886 F70D0101 05050030
2F312D30 2B060355 04031324 494F532D 53656C66 2D536967 6E65642D 43657274
69666963 6174652D 38383734 33333135 301E170D 39333033 30313030 30383234
5A170D32 30303130 31303030 3030305A 302F312D 302B0603 55040313 24494F53
2D53656C 662D5369 676E6564 2D436572 74696669 63617465 2D383837 34333331
3530819F 300D0609 2A864886 F70D0101 01050003 818D0030 81890281 8100BB10
F5361E52 A573FE8A 247142AD CF53D762 38F7BB42 7E723B2B 5C78100E 7F312442
3BE63A8B 7E826758 3F2914D0 4BBC93A6 CCACA795 927514E7 74561589 444D03BA
C20B80D8 85E52A18 C3B287BF 4A1EEF83 B43DD673 12BF075F 7CA038C0 C31F1FB4
F75C3F86 C09DC703 FB05676B 16B86754 F0F11D4D 36B61F81 DF15C02A 9C410203
010001A3 53305130 0F060355 1D130101 FF040530 030101FF 301F0603 551D2304
18301680 14999B3B 7F4B10FA B95CC90B D7218636 39280AFE 4E301D06 03551D0E
04160414 999B3B7F 4B10FAB9 5CC90BD7 21863639 280AFE4E 300D0609 2A864886
F70D0101 05050003 81810076 27E215C4 C105C66D 15124645 D3F4A538 F977A95F
7AF0FF05 648D41A4 A796F9CB CC6327FF 726DA1D6 290CD438 C2111DF8 208B92B5
63B09FEC 1CA334F7 A4607E71 18EBCB44 0A175BEE 30689849 B4D9222E 7EB1C1DB
F36BDDD3 3F5514A6 8A006A8A A113A44D 7337B6D8 7860AA25 EBAD5588 8543DF88
9E6A3D62 6E875372 277B57
quit
crypto pki certificate chain WGB-PEAP
dot1x credentials MyCreds
username DOMAIN\AD-USER
password AD Password
username Cisco password 7 00271A150754
username DOMAIN\AD-USER
bridge irb
interface Dot11Radio0
no ip address
no ip route-cache
encryption mode ciphers aes-ccm
ssid BYO
antenna gain 0
stbc
beamform ofdm
station-role workgroup-bridge
bridge-group 1
bridge-group 1 spanning-disabled
interface Dot11Radio1
no ip address
no ip route-cache
shutdown
encryption mode ciphers aes-ccm tkip
ssid BYO
antenna gain 0
no dfs band block
channel dfs
station-role root
bridge-group 1
bridge-group 1 subscriber-loop-control
bridge-group 1 spanning-disabled
bridge-group 1 block-unknown-source
no bridge-group 1 source-learning
no bridge-group 1 unicast-flooding
interface GigabitEthernet0
no ip address
no ip route-cache
duplex auto
speed auto
bridge-group 1
bridge-group 1 spanning-disabled
interface BVI1
no ip address
no ip route-cache
ip forward-protocol nd
no ip http server
ip http authentication local
ip http secure-server
ip http help-path http://www.cisco.com/warp/public/779/smbiz/prodconfig/help/eag
ip radius source-interface BVI1
radius-server attribute 32 include-in-access-req format %h
radius-server host xxxx auth-port 1812 key 7 xxxx
radius-server vsa send accounting
bridge 1 route ip
line con 0
logging synchronous
line vty 0 4
transport input all
end
Jan 5 14:34:30.636: %DOT11-4-CANT_ASSOC: Interface Dot11Radio0, cannot associate: Associating
Jan 5 14:36:23.730: %DOT11-4-CANT_ASSOC: Interface Dot11Radio0, cannot associate: Associating
Jan 5 14:36:42.730: %DOT11-4-CANT_ASSOC: Interface Dot11Radio0, cannot associate: Associating
Jan 5 14:38:19.833: %DOT11-4-CANT_ASSOC: Interface Dot11Radio0, cannot associate: Associating
Jan 5 14:39:33.901: %DOT11-4-CANT_ASSOC: Interface Dot11Radio0, cannot associate: Associating
Jan 5 14:40:49.948: %DOT11-4-CANT_ASSOC: Interface Dot11Radio0, cannot associate: Associating
Jan 5 14:42:10.123: %SYS-5-CONFIG_I: Configured from console by console
Jan 5 14:42:42.031: %DOT11-4-CANT_ASSOC: Interface Dot11Radio0, cannot associate: No Response
Jan 5 14:42:46.031: %DOT11-4-CANT_ASSOC: Interface Dot11Radio0, cannot associate: Associating
Jan 5 14:43:06.058: %DOT11-4-CANT_ASSOC: Interface Dot11Radio0, cannot associate: Associating
Jan 5 14:45:18.173: %DOT11-4-CANT_ASSOC: Interface Dot11Radio0, cannot associate: Associating

With PEAP there is a certificate being used on the radius server for securing the first phase (outer tunnel). In this scenario the access-point acts like a dot1x client, so like any other client it has to validate the certificate the radius server uses. Therefor the root certificate (and intermediates, if being used) needs to be installed on the access-point.
I never configured an WGB in this way, so I fired on my lab to see if I could get it to work. Sadly I did not manage to get it to work properly, I'm running into "EAP session timed out" messages in ACS (my radius server). I did also ran into the MFP issue, but as long as you configure MFP as optional on the network side, it should work. Because of the CCIE exam, I'm running old AirOS software on the WLC and also the software on the access-point I tested this configuration on (2600) is not that new. So it could be that I ran into a bug testing this, so I would advise you to run the latest software on your 1600. There are WGB related bugs fixed not so long ago. This configuration is supported since IOS 15.2.2(JA) and higher.
If I look at your configuration you still need to actually install the certificate, the trustpoint is empty. Besides that the following configuration changes needs to be made:
eap profile EAPTLS
no method mschapv2
method peap
dot11 ssid BYO
authentication open eap PEAP
   no authentication shared eap eap_methods
authentication network-eap PEAP
authentication key-management wpa version 2
dot1x credentials MyCreds
dot1x eap profile EAPTLS
   no infrastructure-ssid
   no ids mfp client optional
For more information look at this document.

Workgroup Bridge and local Wifi Config

Hi all, hoping you can help me with this, just need an other brain as mine is empty as I've been staring at this for too long!!!
What I'm trying to config is to have a standalone local WLAN (Built into a VAN) running on the 2.4ghz and then also have a workgroup bridge on the 5ghz to the corporate lan.
Setup is this:
2960<-->1142(autonomous)   <--Workgroup bridge on 5Ghz--> 1131(Lightweight)<3560>--<5508WLC> (hope that makes sense!!)
So far I have the bridge working, the 1142 connects to a ssid on the 1131 using psk. I can see the 1142 as an assosiated client on the wlc and I can ping the the lan from the 1142 so I'm happy the bridge is working.
Clients connected to the 2.4ghz ssid on the 1142 can only ping through as far as the AP(1142) I can't seem to get the traffic to pass across the bridge, is there something I need to do to link the 2.4 to the 5ghz bridge link?
Any help always appreciated, cheers.

dmantill - Thanks for your link. I have read through and checked my config but my plan is to have a number of clients, all dhcp assigned, connecting to the do0 int for local wlan breakout.
I'm not sure that the passive config will help me there.
Steven - I have enabled the wgb on the do1 int and I am connecting clients on the do0 int for local wlan breakout. Enabling the WGB has not disabled the other radio on my setup.
I was running 7.0.98.0 but have today upgraded to 7.0.98.218 on my WLC but that has not helped.
From what I can tell it looks like my problem just lies with routing traffic across the 2 radios. My local clients can ping as far as the WGB and if I CLI into the WGB AP I can ping the corporate lan on the otherside of the bridge and can also ping from the lan to the WGB. I just cannot seem to get the 2 ssid's to route between each other.
Here's my WGB config, hope this brings some more ideas!!
Cheers,
Jason.
Current configuration : 1555 bytes
version 12.4
no service pad
service timestamps debug datetime msec
service timestamps log datetime msec
service password-encryption
hostname XXX
logging rate-limit console 9
enable secret 5 $1$ujWI$HMYMAjMfJV2J2WaGa1/JJ0
no aaa new-model
dot11 syslog
dot11 ssid XXX
   authentication open
   authentication key-management wpa
   guest-mode
   wpa-psk ascii 7 105A0C0A11001D1908
dot11 ssid XXX
   authentication open
   authentication key-management wpa
   guest-mode
   wpa-psk ascii 7 080F15480C090D1221
username Cisco password 7 02250D480809
bridge irb
interface Dot11Radio0
no ip address
no ip route-cache
encryption mode ciphers tkip
ssid XXX
antenna gain 0
station-role root
bridge-group 1
bridge-group 1 subscriber-loop-control
bridge-group 1 block-unknown-source
no bridge-group 1 source-learning
no bridge-group 1 unicast-flooding
bridge-group 1 spanning-disabled
interface Dot11Radio1
no ip address
no ip route-cache
encryption mode ciphers tkip
ssid XXX
antenna gain 0
station-role workgroup-bridge
bridge-group 1
bridge-group 1 spanning-disabled
interface GigabitEthernet0
no ip address
no ip route-cache
duplex auto
speed auto
no keepalive
bridge-group 1
bridge-group 1 spanning-disabled
interface BVI1
ip address dhcp
no ip route-cache
ip http server
no ip http secure-server
ip http help-path http://www.cisco.com/warp/public/779/smbiz/prodconfig/help/eag
bridge 1 route ip
bridge 1 aging-time 216000
line con 0
line vty 0 4
login local
end

Unreachable device behind a workgroup bridge

Hello,
we have a problem, that already occured at two locations:
We installed workgroup bridges (at one location a AP-1242AG connecting to an IOS-AP, at the other location a AP-1131AG connecting to a controller-based WLAN). Behind these workgroup bridges there are devices that talk very little by themselves (about one packet per hour).
So in the IOS-WLAN they are reachable only after pinging the device from the AP to which the WGB is connected. In the controller-based WLAN they are only reachable from the WGB itself, not from the rest of the LAN.
My suspicion is, that these devices disappear from the ARP-/Mac-Address-tables because of the little traffic they send. How can we work around this problem? Static ARP- and/or MAC-Entries? But where to place them, in the core, on the APs?
I would appreciate any help.
Thanks,
Sebastian

Here is the URL for the WLC configuration and troubleshooting guide which will help you :
http://www.cisco.com/en/US/tech/tk722/tk809/technologies_tech_note09186a0080810880.shtml
http://www.cisco.com/en/US/products/hw/modules/ps2797/products_tech_note09186a0080811085.shtml

Configuration of a Point to MultiPoint link with Cisco Aironet 1310 bridges

Hi All,
The previous problem of which I started another conversation here:
http://forum.cisco.com/eforum/servlet/NetProf?page=netprof&forum=Wireless%20-%20Mobility&topic=General&CommCmd=MB%3Fcmd%3Ddisplay_location%26location%3D.1ddba023
somehow dissapeared. It could have been a problem of interferences.
I have another issue with other (multipoint) wireless WAN link, which I hope has a solution.
On the central node, we have an Cisco Aironet 1310 bridge configured as root-bridge. It has a panel of four vertical polarity 17 dBi panel 90? antennas, with more than enough gain (there is a 250 mWatts 802.11 b/g amplifier, before the 4-way splitter) and excellent line of sight to three remote bridges.
The three (03) remote bridges are also Aironet 1310 models, confidured as non-root-bridges.
The problem we have is that it seems that when the three remote links operate concurrently the amount of lost packets is huge. When I shutdown the radio interfaces of two bridges, the remaining bridge makes an excellent link with the central node.
It seems that some hours are more critical than others, also the links operate much worse when there is some (small) network traffic in them.
I have read the 1310 manuals, and I can't find a sample configuration for point to multi-point links.
Does someone knows what radio interface configuration should I need to use to establish better quality communication?
I mean, perhaps the 1 x root - 3 x no root configuration is not recommendable for the multipoint link configuration.
Any hints will be welcome.
Best Regards,
Igor Sotelo.

Hi All,
Thank you for the information. I configured the distance on the root bridges, but the links showed instability.
I'm using a bi-directional amplifier. It has two pieces. According to the manuals, one is installed indoors, the other outdoors. I'm not sure if the indoors piece has the transmition module or it's only the injector.
We could establish connection at 7 km (around 4 milles) distance from the central point, using 24 dBi antennas on the other side.
However, we have issues with a near located point that is only 1.2 Km (around 0.8 milles) away and has a 13 dBi integrated patch antenna. The signal strenght value we get there is in the -62 to -68 dBm range, and is noticiably (5-10 dBm) lower than the strenght we get at other points of the link. And I have trouble establishing a high quality link with that point, using OFDM modulation. I tend to think that if I remove the amplifier I'm not going to reach that point at all. The EIRP on the central iste is 34 dBm / 2.5 watts, without amplifier it would be 26 dBm / 0.4 watts.
On the opposite sites the EIRP is 33 dBm / 2 watts using CCK or 28 dBm / 0.63 watts using OFDM.
When one looks at the central site from that point, an Motorola Canopy with passive reflector (EIRP 48 dBm or around 64 watts) can be seen. It doesn't have the same direction, but the opposite site must be large distance and could interfere with my wireless network. Attached is an amplified photo of the view. It's safe to assume that the Canopy operates in the 2.4 GHz frequency range.
Once I connect the point at 1.2 Km, the multipoint link loses its quality, and soon the lost packets get too frequent.
The CCK seems to be much more interfered than OFDM, I guess because of that canopies.
Another thing I'm wondering about is if the Aironet 1310 can continuosly switch CCK-OFDM over the same point - multipoint link, without losing packets.
What other parameters should I tweak? Is there a way to avoid interferences fromt the canopy?
I would like to apply 100 mWatts local power using the radio with OFDM, but it seems that's not possible.
Best Regards,
Igor Sotelo.

Using the 1262 AP in Workgroup Bridge Mode

Client has a building that is located 300Ft apart and would like to provide IP communications for 3-4 IP hadsets back to an IP PBX. They do not want to dig up the parking lot so we proposed using a wireless bridge. I noticed that Cisco discontinue the 1300 and 1400 Wireless Bridge. Can I use a 1262 with external antenna in Workgroup Bridge mode to perfom this functions? I will put a Layer 3 switch on both ends to route traffice (3560C-8). Should I use the Yagi antenna's for outdoor use? Thanks!

You could go WGB, but root/non-root might work better. This will allows you to pass multiple VLAN across the link.
This is a bit old, but it' the Bridge Range utility
http://www.cisco.com/en/US/prod/collateral/wireless/ps5678/ps458/prod_technical_reference09186a00800a912a.xls
HTH,
Steve
Please remember to rate useful posts, and mark questions as answered

Cisco Aironet 1310 ios problem

I have Cisco 1310 wireless bridge and i don't know how but its operating system is not working any more i have the operating system in Tar file but when i try to upload it to the bridge it gives me the below message and i cant figure out what the problem is please help me
bridge: tar -x tract://10.1.1.3/c1310-k9w7-tar.123-11.JA1.tar flash:
usage: tar <-table | -x tract> <tar file> <destination>

Looks like there is an issue of the boot image. You have to follow steps given in below link recover from this.
http://www.cisco.com/c/en/us/td/docs/wireless/access_point/1300/12-3_7_JA/configuration/guide/brsc1237/b37ts.html#wp1071147
NB: Most of us (including me) who respond to your query in this forum are not Cisco employees. We voluntarily support on this forum according to the free time we got. If you want to get direct Cisco support you have to raise a TAC case provided that you have maintenance contract with them for these products.
HTH
Rasika
*** Pls rate all useful responses ****

Can a Workgroup bridge 352 act as a LEAP client (supplicant) ?

Is it possible for a WGB in Version 8.84 to act as a LEAP client (supplicant) instead of the connected client NICs in the workgroup?
This question is as important as the workgroup could be composed of IP Cameras or other IP devices who could not act as a LEAP Client.
Thank you
Jacky

Hi,
It is not so clear as it seems to be, because several CCO documents are introducing this LEAP ability of the WGB but none of them give details.
http://www.cisco.com/en/US/products/hw/wireless/ps458/products_data_sheet09186a0080088833.html
"For authentication of devices attached to the workgroup, a username and password may be stored in the workgroup bridge in either static or dynamic memory. When authenticated, the workgroup bridge receives a single-session, single-user encryption key from the Remote Access Dial-In User Service (RADIUS) server via the associated AP. With this centralized and standards-based architecture, wireless security scales to meet the requirements of any enterprise."
AND
http://www.cisco.com/warp/customer/cc/pd/witc/ao1200ap/prodlit/wrsec_an.htm
"Figure 6: Workgroup Bridge Security Configuration"
What do you mean about ??
Jacky

Workgroup Bridge between WRVS440n and WAP321

Hi, i am trying to expand the wifi range of my WRVS4400n. Since the WAP4400 is'nt available i got me a wap321, since it was mentioned as recommende replacement. However i am having trouble in getting the bridge to work.
First i tried to use WDS but this only killed my WRVS4400n and i am now trying the Workghroup Bridge mode on the WAP321.
On WRVS4400n i have enabled WDS and have tried both auto setting and Manual without any difference
I am stuck with this status on the WAP321:
Network Interface Status and Statistics VLAN ID Name (SSID)
WLAN0UPSTRM Disconnected 1 myssid
WLAN0DWSTRM Up 1 myssid
It is the Infrastructure Client Interface setting that fails, i've tried both None and WPA pesronal Security setting with same result: Disconnected
What am i missing?

Hello Lars,
Just wanted to add a note to this as well. Pretty much the workgroup bridge is made to be used with other wireless devices that are not WAP121's and WAP321s. Cisco pretty much recommends to use WDS bridge if you have another WAP321 or WAP121.. if that is not the case then workgroup bridge is your other options. The admin guide should have some good documentation on this and also if you click on help in the GUI of the WAP321 it provides a lot of great information as well! It gives you recommended set up for this configuration.
Other than that you do not have to set up WDS on the WRVS4400n. As long as the SSID, wireless channel, wireless mode, wireless bandwidth and secuirty is the same on the WAP321 and the WRVS4400n this should work out just fine. Maybe have to power cycle the devices a couple times to get it to come up but I know I have gotten this to work between a RV220w and a WAP321... so I do not see why it shouldn't work between the WRVS4400n and the WAP321.
Hope that helps!
Thanks,
Clayton Sill

H-REAP and Workgroup Bridge

Has anyone setup a Workgroup Bridge on a remote H-REAP site and got it working? I have the AP associated to the controller but the AP cannot ping the controller and the controller cannot see the wired clients on the AP.

Hello, yes we current have many WGB's connected to FlexConnect LAP's. Support for connecting to FlexConnect LAP's (formerly H-REAP) has been added in WLC Code 7.3. Please refer to release notes: http://www.cisco.com/en/US/docs/wireless/controller/release/notes/crn73.html
Thank you.

How to setup LAPAC1750-PRO with LAPAC1750 Workgroup Bridge Mode as WiFi Extender

I've got following devices:
1 LRT224 Dual WAN Gigabit VPN Router (Load Balancing)
2 LAPAC1750-PRO Access Points
6 LAPAC1750 Access Points
I'm supposed to make a Cluster between 2 LAPAC1750-PRO and then connect the 6 LAPAC1750 using Workgroup Bridge Mode, but after purchasing and while configuring, I found the strage thing that:
If I need to setup a Workgroup Bridge Mode, the clustering will not be available (so I need to modify the changes on either PRO APs whenever I need to perform some) and the Bridge Mode needs to be disable if Clustering is ON or vice versa.
Spoiler (Highlight to read)
+--- The Configuration ---+
I've made 2 subnets:
192.168.1.x (Existing)
192.168.10.x (New)
and configured 4 APs on each (1 PRO and 3 Normal using Trunking between 2 HP 1910 24 Switches) and then again found some strange thing that:
Only 1 Normal AP can be connected to PRO in a Workgroup Bridge Mode, and vice versa.
+--- The Configuration ---+I've made 2 subnets:192.168.1.x (Existing)192.168.10.x (New)and configured 4 APs on each (1 PRO and 3 Normal using Trunking between 2 HP 1910 24 Switches) and then again found some strange thing that: Only 1 Normal AP can be connected to PRO in a Workgroup Bridge Mode, and vice versa.
+--- The Problem ---+
--- Please correct me if I'm wrong
It supposed to extend the Wireless Range, therefore I need to do the following:
PRO AP needs to connect to the AP 1 of and the AP 1 then connects to AP 2 and so on in Workgroup Bridge Mode ...
OR
All the APs needs to connect to the PRO one by registering one by one in Workgroup Bridge Mode
Thanx in Advance

Thanx! The information is very helpful.

When i open pc an adobe bridge problem denotes purging

when i open computer an adobe bridge problem denotes purging

Are you trying to say that pointing to your computer in Bridge you get an error message telling you that you need to purge the central Cache?
If so, go ahead and purge it.
Your post is not clear at all. Try rephrasing it, please.
Also:
A lot more information about your hardware and software is needed.
BOILERPLATE TEXT:
If you give complete and detailed information about your setup and the issue at hand,
such as your platform (Mac or Win),
exact versions of your OS, of Photoshop (not just "CC", but something like CC2014.v.2.2) and of Bridge,
your settings in Photoshop > Preference > Performance
the type of file you were working on,
machine specs, such as total installed RAM, scratch file HDs, total available HD space, video card specs, including total VRAM installed,
what troubleshooting steps you have taken so far,
what error message(s) you receive,
if having issues opening raw files also the exact camera make and model that generated them,
if you're having printing issues, indicate the exact make and model of your printer, paper size, image dimensions in pixels (so many pixels wide by so many pixels high). if going through a RIP, specify that too.
a screen shot of your settings or of the image could be very helpful too,
etc.,
someone may be able to help you (not necessarily this poster, who is not a Windows user).
Please read this FAQ for advice on how to ask your questions correctly for quicker and better answers:
http://forums.adobe.com/thread/419981?tstart=0
Thanks!

CS6 Bridge and Mini Bridge problems

Installed CS6 and clicked on Brose in Bridge. I get the rror messare could not complete the Brose in Bridge commmand because Photoshop was unable to find the Java Script plugin. Also when clicking on Brose in Mini Bridge I get the message cannot complete the command because the extension could not be loaded I have uninstalled CS6 and reinstalled it and get the samew message Help please

Thank you very much I will try that
In a message dated 11/24/2014 12:41:45 P.M. Central Standard Time,
[email protected] writes:
CS6 Bridge and Mini Bridge problems
created by Flashy1995_ (https://forums.adobe.com/people/Flashy_1995) in
Photoshop General Discussion - View the full discussion
(https://forums.adobe.com/message/6958475#6958475)

Question re: BR1310 in Workgroup Bridge Mode

When a BR1310 is in Workgroup bridge mode, it can provide a wired connection from the BR to a device. Can it also service wireless users?

If I understand your question you need more equipment to provide wireless connectivity from the location of the WGB. Add a switch/hub to the output of the BR1310 and an Acess Point to one of the hubs ports.

Answers to common Bridge problems.

Here are user-submitted answers to common Bridge problems.
I invite all suggestions to addition/corrections/improvements.

Bumped. I'll convert to document once it will be possible to do so. I have great addendum by CurtY:
Windows and Mac FAQ and Translation Key
Keystrokes
ALT on a Pc = Option on a Mac (On some keyboards (UK), the Option key is labeled with Alt. )
CTRL (Control) on Pc = Cmd (Command) on a Mac, the key has the following symbol: ⌘
Right-click on a Pc = Right-click on a Mac, or Control+Click on machines without a mouse.
Menu differences
Preferences (CMD+K) are found on the Photoshop menu on a Mac, at the bottom of the Edit menu on a PC, and the shortcut is (CTRL+K).
On the same Photoshop menu on a Mac, one can find About Plug-ins... and About Photoshop, while they are located on the Help menu on a PC.
Quit Photoshop (CMD+Q) is also on that Photoshop menu on a Mac, while Exit (CTRL+Q) can be found at the end of the File menu on a PC.
Preferences location on the hard drive. There is a full document on that topic: http://kb2.adobe.com/cps/828/cpsid_82893.html
but basically: The main preference file, is on both plaform Adobe Photoshop CSx Prefs.psp it is located, alongside most other preferences on:
Mac location: Users/[user name]/Library/Preferences/Adobe Photoshop CSx Settings
Windows XP: Documents and Settings/[user name]/Application Data/Adobe/Adobe Photoshop CSx/Adobe Photoshop CSx Settings
Windows 7 and Vista: Users/[user name]/AppData/Roaming/Adobe/Adobe Photoshop CS5/Adobe Photoshop CSx
Settings Keywords
pc = C:/Users/user name/AppData/Roaming/Adobe/BridgeCSx/ (note: to view AppData turn on hidden file option)
Mac = (your computer name)/ Library / App Support / Adobe / Bridge CSx / Adobe
Camera Raw location NOTE: Should be only one file here.
PC = Program Files/COMMON Files/Adobe/Plug-ins/CSx/File Formats which gives you Camera Raw.8bi
Mac = /Library/Application Support/Adobe/Plug-ins/CSx/File Formats/
Photoshop Actions
Mac - Actions (not saved) Actions panel.psp Users/[user name]/Library/Preferences/Adobe Photoshop CSx Settings
Mac - Actions (saved) Actions panel.atn Program Files/Adobe Photoshop CSx(64bit)/presets/actions
PC - Actions (not saved) Actions panel.psp Users/[user name]/AppData/Roaming/Adobe/Adobe Photoshop CS5/Adobe Photoshop CS5 Settings
PC - Actions (saved) Actions panel.atn Program Files/Adobe Photoshop CSx(64bit)/presets/actions

Cisco AP1121G Workgroup Bridge Problem

Similar Messages

Maybe you are looking for