Cisco Prime 1.3

I did an opps and deployed the latest IOS image to all of our switches, I have looked and looked for a way to stop the deployment. Right now I have stopped the the service but I need to find out a way to stop the deployment when I turn Prime back on???
Thanks

Hi,
Prime Infra# ncs stop - Stops the Cisco Prime Infrastructure server
Prime Infra# ncs status - Shows the Cisco Prime Infrastructure server status
Prime Infra# ncs start - Starts the Cisco Prime Infrastructure server
Regards
Dont forget to rate helpful posts

Similar Messages

  • Issues with Cisco Prime LMS 4.2.3

    Hi,
    I'm trailing Cisco Prime LMS 4.2.3 Soft appliance on ESXi before I deploy it into a live environment and am having some issues.
    I've upgraded to version 4.2.3 and the box was working fine after the upgrade however on power it up today the Apache service will not start.
    If I look at the LMS application I see this for the Apache service.
    "Apache                Administrator has shut down this server   0 "
    I have tried to starting it.
    CiscoLMS42/admin# application start Apache
    % Application failed to start
    CiscoLMS42/admin#
    If I run an application operation debug at the same time I get the following output.
    CiscoLMS42/admin# 6 [5343]: application:operation cars_install.c[1145] [admin]: Application initialization initiated for appname: Apache, operation: 0
    7 [5343]: application:operation cars_install.c[1146] [admin]: Operations: O-APP_START, 1-APP_STOP, 2-APP_STATUS
    6 [5343]: application:operation cars_install.c[1150] [admin]: Verifying app (Apache) is installed ...
    3 [5343]: application:operation cars_install.c[1152] [admin]: App (Apache) is not installed.
    3 [5343]: application:operation install_cli.c[281] [admin]: Error while starting application  - Application: Apache ErrorCode: -999
    I'm at a complete lose as to where to look next, failing anything else I'll have to rebuild it, but it would be nice to know how to get the Apache up and running again.
    regards
    Rich

    Hi Richard,
    I see the following:
    [ Thu Apr 18 20:53:11 GMT 2013 ] TomcatMonitor After gettingAJPPort : ajpPort = 9009 and host =CiscoLMS42
    [ Thu Apr 18 20:53:11 GMT 2013 ] TomcatMonitor theMgr constructor successful.
    [ Thu Apr 18 20:53:11 GMT 2013 ] TomcatMonitor Inside whileloop
    [ Thu Apr 18 20:53:11 GMT 2013 ] TomcatMonitor Tomcat is not ready, it's coming up Connection refused
    It looks like the hostname cannot be resolved. Can you try to add a static entry in /etc/hosts for the IP of the server and CiscoLMS42?
    Restart the daemon manager and it should work.
    Regards,
    Vlad
    ==========
    NMS Team
    Krakow, Poland
    Cisco TAC

  • Cisco Prime Infrastructure 1.2 is not working https & ncs

    Hi, I have just deploy Cisco Prime Infrastructure 1.2 in a virtual appliance (Vmware Esxi 5.1). Console is ok & setup is also completed. but there is no NCS application. only app is shwoing: NCSPNP
    Cannot access from https also.
    Please suggest how to Starting Prime Infrastructure Serve

    From what you describe, it sounds like you have installed the Plug and Play (PNP) ova image. You need to install the Prime Infrastructure image.
    See the screenshot below for details (click to enlarge):

  • How to customize email notifications sent by Cisco Prime.

    Hi,
    We have been receiving email alerts for any unresponsive devices in Cisco Prime. I was able to find the option to customize the subject for such email alert under Admin-Network-Notification and Action settings, however I am not able to locate the option to change the email body.
    The email body for such alerts has lot of unrequired information which I would like to remove.
    Can someone provide me the options on how to get rid of such information in the email body.
    Regards

    Hi ,
    To customize the e-mail subject:
    Step 1 Select Admin > Network >  Notification and Action Settings > Fault - Email subject  customization.
    The available and selected lists of the subject attributes for e-mail  are displayed.
    To customize the e-mail subject, you can add and remove subjects from  the current e-mail subjects list. By default, following list of e-mail  subject attributes are displayed in the Selected Subjects for E-Mail  box.
    •Event ID
    •Device Name
    •Time
    •Severity
    •Event Name
    •Status
    To add a subject:
    a. Select the subject attribute  from Available Subjects for E-Mail.
    b. Click Add.
    The selected subject attribute is added to the Selected Subjects for  E-Mail list.
    You can add a subject attribute only from the Available Subjects list to  the Selected Subjects list. You cannot add a subject attribute from the  Selected subject list to the Available Subject list.
    To remove a subject attribute:
    a. Select the subject attribute  from Selected Subjects for E-Mail.
    b. Click Remove.
    The selected subject attribute is removed from the Selected list and  added to the Available subjects for E-Mail list.
    You can remove a subject attribute only from the Selected Subjects list  and not from the Available Subjects list.
    Step 2 Click Up or Down to rearrange the  order of the selected e-mail subject attributes.
    Step 3 Click Apply to save the customized e-mail  subject attributes.
    Note: Other than this you will not be able to customize any thing, User-defined fied option will not work.
    I hope this will help
    Thanks
    Afroz

  • Ask the Expert: Overview of Cisco Prime Service Catalog and Process Orchestrator Solutions

    Welcome to this Cisco Support Community Ask the Expert conversation. This is an opportunity to learn and ask questions about the Cisco Prime Service Catalog and Process Orchestrator solutions.
    Cisco expert Jason Davis will discuss Cisco’s network management products offered under the Cisco Prime framework. If you have questions about Cisco Prime infrastructure or data center automation with our Cisco Prime Service Catalog and Process Orchestrator solutions, join us on the Cisco Support Community.
    Jason Davis is a distinguished services engineer in the Intelligent Infrastructure Practice team of Cisco Advanced Services. His role is to provide strategic and tactical consulting for hundreds of Advanced Services customers, lead service innovation, and assess new services and technologies. Jason's primary expertise areas are in network management systems, intelligent automation, virtualization, data center operations, software-defined networking, and network programmability.
    Based out of the Research Triangle Park (RTP) campus, Jason is also responsible for administering the Research Triangle Park Network Management Lab, Cisco's largest network management lab.
    Since joining Cisco in 1998, Jason has been a frequent speaker at Cisco's Networkers and CiscoLive conferences in the United States and Europe. In the past five years he has also been involved in the conference network setup and monitoring. He is a much sought-after resource by the field sales teams to assist with presales solutions and executive briefings. He has provided strategic and tactical network management consulting for several hundred customers.
    Jason is a subject matter expert with the following products and features:
    Cisco Prime LAN management solution
    Cisco Prime infrastructure
    CiscoSecure ACS
    Cisco Prime Network Registrar
    Cisco Process Orchestrator
    Cisco Prime Service Catalog
    Cisco IP SLA
    Embedded Event Manager
    SNMPv3
    onePK and OpenFlow
    Cisco UCS
    Device instrumentation
    VMware ESX, ESXi, and vCenter
    ITIL
    Jason received his bachelor of science degree in electrical engineering from the University of Miami (FL). He has been married for 20 years and has 4 children. His interests include providing audiovisual technical support for churches and conference venues, camping and biking with his family, remote-control helicopter piloting, paintball, and recreational shooting.
    Remember to use the rating system to let Jason know if you have received an adequate response.
    Because of the volume expected during this event, Jason might not be able to answer every question. Remember that you can continue the conversation in Data Center > Intelligent Automation under the subcommunity Cisco Prime Service Catalog shortly after the event. This event lasts through September 12, 2014. Visit this forum often to view responses to your questions and the questions of other Cisco Support Community members.

    Hello Jason,
    Thank you very much for welcoming me to your expert discussion :) I feel to be in the right place, at the right time. Thank you also for answering question beyond your scope here, much appreciated. The information received will help me to go further as such I have submitted a 5 start rating for your first reply.
    That sounds promising about the LMS part so yes, I stay tuned and wait patiently.
    Ok, now let’s revert to the actual topic discussed here. Cisco Prime Service Catalog and Process Orchestrator solutions I have briefly read up on this on CCO (where elseJ) and picked out the following quote
    ---- Quote from the Cisco Prime Service Catalog Data Sheet
     Today’s end users want self-service and easy access to IT tools and services.
    Simultaneously, organizations are seeking ways to extend their cloud management
    platforms beyond self-service delivery of virtual machines and infrastructure resources
    while increasing their use of cloud-based solutions to enhance business agility and effectiveness.
    Cisco Prime™ Service Catalog offers tremendous benefits to organizations that want to unify the ways in
    which all types of IT services are ordered and fulfilled, not just infrastructure requests
    ---- un quote ---
    I try to understand what (at high level of course) happens in the back ground when an order is raised and which vendor solution your product can interact with.
    As mentioned in the quoted text, this service catalogue goes beyond the standard infrastructure.
    Let’s say, a user wants to deploy a new email services, or in your example,  extends or create a new web-portal (i.e. for HR to view and manage holiday, staff absence and benefits).
    Your solution will need to interact somehow with the 3rd party vendor application that is capable building such portal I believe.
    Without disclosing to many information, I assume the portal is linked to backend VM,s that spin up requested resources (and more magic of course). Perhaps I am mixing this up with another cisco product where a user can go on the portal and spin up virtual Firewalls, virtual Routers can be provisioned in now time.
    Out if interest; Is this product also known as Mozart? (project code within Cisco?)
    I hope query is ok.
    Best wishes
    Markus

  • Ask The Expert: Understanding, Implementing, and Troubleshooting Cisco Prime Network

    Ask questions and learn about Cisco Prime Network with Cisco experts Vignesh Rajendran Praveen and Jaminder Singh Bali.
    Cisco Prime Network is and  Cisco Prime Network provides cost-effective device operation, administration and network fault management for today’s complex and evolved programmable networks (EPNs). It is a single solution to support both the traditional physical network components, as well as compute infrastructure, and the virtual elements found in data centers. Automated configuration and change management combined with advanced troubleshooting and diagnostics greatly help service providers enable proactive service assurance. Additionally, the flexible and extensible architecture is designed to support the multivendor environment, helping to lower operational costs.
    This event runs January 5 through January 16, 2015.
    Vignesh Rajendran Praveen is a High Touch Engineer with the Focused Technical Services team supporting Cisco's major Service Provider customers in Routing, Switching, Multiprotocol Label Switching (MPLS) technologies and Cisco Prime Network related issues. Previously at Cisco he has worked as a Network Consulting Engineer for Enterprise Customers and as a Customer Support Engineer for Service Provider customers. He has been in the networking industry for ten years and holds CCIE certification (#34503) in the Routing and Switching as well as Service Provider tracks.
    Jaminder Singh Bali is a Customer Support Engineer working in SP-NMS TAC team, supporting Cisco's major service provider customers in Cisco Prime Network, Performance and Prime Central related issues. His areas of expertise include Oracle, Linux and NMS applications. He has been in the industry for past six years.
    Remember to use the rating system to let the experts know if you have received an adequate response. 
    The Experts might not be able to answer each question due to the volume expected during this event. Remember that you can continue the conversation in Network Infrastructure community, sub-community, LAN, Switching and Routing discussion forum shortly after the event. This event lasts through January 16, 2015. Visit this forum often to view responses to your questions and the questions of other community members.

    Hello Jerome,
    A variety of Cisco devices are supported by the the Cisco Prime Network. I would encourage you to go through the below links on the user guide depending the version of Cisco Prime Network being used.
    "Cisco Prime Network Supported Cisco Virtual Network Elements (VNEs)"
    "Cisco Prime Network Supported Cisco VNEs - Addendum"
    Below is the link for the user guide.
    http://www.cisco.com/c/en/us/support/cloud-systems-management/prime-network/products-user-guide-list.html
    Hope this would help in providing you more clarity.
    ***********Plz do rate this post if you found it helpful*************************
    Thanks & Regards,
    Vignesh R P

  • What are the features supported in Cisco Prime Infrastructure for WLAN for autonomous AP's?

    What are the features supported in Cisco Prime Infrastructure for WLAN for autonomous AP’s?

    • PI provides visibility for autonomous  clients within the same list view as lightweight and wired clients (client list  page).
    • Rogue AP detection for autonomous AP's is not supported (it's  supported in CUWN). 
    • Alarms/events for client authentication issues (e.g.  authentication failure) are displayed in PI.
    • Config management for  autonomous AP's is via CLI template.  Config comparison and archiving  functionality in PI leverages these same features that were brought in from LMS,  so need to defer to others in terms of whether this is a cross-platform feature  in PI or is only supported on a subset of platforms.  Config comparison/archive  is supported in CUWN.PI supports both infrastructure (e.g. AP Tx Power and  Channel, busiest AP, AP utilization, etc.) and client (e.g. client count, client  sessions, etc.) reports, and there are extensive reports for CUWN

  • Replicate in the Master controller and creation of new user with cisco prime infrastructure 2.1.

    Hello!!
    We have multiple controllers Cisco WLC 5508 (all running software version 7.6.120.0) distributed in various buildings and a controller in other control building (also Cisco WLC 7.6.120.0 5508) operating as Master and backup of the buildings's controllers . 
    Each building is radiated such an SSID that is used as a validation of the user connected to that SSID web portal each controller (in the WLAN, Security -> Layer 3 -> Web Policy), using the local database to validate the user. 
    The problem is that the local database of users is not being replicated between controllers buildings and the Master controller, so if you drop the controller of a building, the Master controller begins to provide service to the buildings access points, but the equivalent radiated SSID cannot able to validate users. 
    I need know if it's possible through Cisco Prime Infrastruture 2.1, first replicate in the Master controller on the basis of existing controllers buildings each local data and, second, that the creation of new users are automatically perform both the controllers like to the Master .
    Thanks.

    As noted earlier, it is not advisable to use the root user to log in for normal use. New users and groups can be created by navigating to Administration > Users, Roles & AAA as shown in the preceding figures. It would help to chalk out what are the various levels at which you want to distribute the users, and to create those roles first. It doesn’t really matter whether you create users or groups first. New users can be easily added by going to Administration > Users, Roles & AAA > Users > Add Users > Select “Add Users” from the drop-down on the right side. Once you get into the add user workflow, fill in the username, password, and local authorization for this user as shown in the figure below.
    A virtual domain can also be assigned to the users when you define their roles by selecting the virtual domain on the left side and moving it to the right side as shown in the image below (left).

  • Error coming while installing Cisco Prime 4.2 on Windows Server 2008 R2

    Hi,
    I'm trying to install Cisco Prime 4.2 on Windows Server 2008 R2. While initiating the installation, message box "Error: csv not found" appears, and the installation terminates.
    Is there any csv template need to be copied at any location before hand?

    Are you installaing LMS 4.2.4  directly ?
    Looking at the error ,it looks like ...
    If yes then  you need to follow the below path:
    The installation path of LMS 4.2.4 : LMS 4.2 > LMS 4.2.2 > LMS 4.2.4
    Thanks-
    Afroz
    [Do rate the useful post]

  • Cisco Prime 1.2 - cannot delete "Unassigned" Campus

    Hi,
    has anybody an idea how to delete Unassigned Campus?
    I went through I think all documentation and they are speaking that only "System Campus" cannot be deleted, but not a single word about "Unassigned" campus.
    All the campuses below behaves like a child of Unassigned campus. I know it's just cosmetic issue, but still I would like to get rid of it.
    I attached a screenshot.
    Thanks!
    K.

    Yes you can add building and floor diagrams in Cisco Prime Infrastructure 1.2. For the same you can see the below link
    http://www.cisco.com/en/US/docs/wireless/prime_infrastructure/1.2/configuration/guide/maps.html
    Open this link and goto Adding Floor Areas to a Campus Building

  • Issue with backup NCS via NFS (Cisco Prime NCS 1.2.0)

    Hello,
    Does someone have issue with backup NCS via externally mounted location (NFS)?
    I have Cisco Prime NCS 1.2.0 and tried backup it to external resources, but I have issue with my free space:
    NCS/admin# backup ncs repository backup_nfs
    % Creating backup with timestamped filename: ncs-130131-0534.tar.gpg
    INFO : Cannot configure the backup directory size settings as the free space available is less than the current database size.
    You do not have enough disk space available in your repository to complete this backup.
    DB size is 25 GB
    Available size is 12 GB
    Please refer to the command reference guide for NCS and look at the /backup-staging-url/ command reference to setup the backup repository on an externally mounted location
      Stage 5 of 7: Building backup file ...
      -- complete.
      Stage 6 of 7: Encrypting backup file ...
      -- complete.
      Stage 7 of 7: Transferring backup file ...
      -- complete.
    I have tried to add additional space and use command backup-staging-url (my configuration: backup-staging-url nfs://server2008:/nfs), but it didn't help me.
    NFS share works perfect. I have checked it via NFS repository:
    repository backup_nfs
      url nfs://server2008:/nfs
    +++++++++++++++++++++++++++++++++++++++
    NCS/admin# show repository backup_nfs
    NCS-130130-1135.tar.gpg
    NCS-130130-1137.tar.gpg
    NCS-130130-1157.tar.gpg
    NCS-130130-1158.tar.gpg
    test-130130-1210.tar.gz
    Everytime when I try create backup I receive error message "You do not have enough disk space available in your repository to complete this backup".
    Does someone know how can I backup NCS system?
    Thank you

    How much space is availabe on that NFS mount point? It looks like to me from the error message that there is only 12 GB.... 
    The backup-staging-url is just for a space used to stage the backup before it is written-----

  • Cisco prime 4.2 monitor SFP conn & isdn active call session

    Hello all,
    my customer already bought cisco prime 4.2 , they asked me if this cisco prime is able to monitor the SFP (fiber connector) status active/not active and monitor the voice call active session for 24 hours ? anyone can help me to configure it ?
    thanks in advance,

    i couldn't find the appropriate MIB to monitor the call session

  • Cisco Prime Rogue AP Report - No Rogues from 3702 Series AP's

    I am running Cisco Prime Infrastructure (2.1) that manages a Cisco 5508 WLC (7.6). We have multiple version of AP's managed by this WLC to include 1142, 2602, 3702, etc...In Cisco prime when we run a Rogue AP Report. None of the Rogue AP's discovered by 3702's are displayed in the report. The Rogues show on the WLC though from all AP's. Cannot find a reason for this. Any ideas?

    The Rogue alarm state always stays on "removed" once deleted
    CSCuo91446
    Description
    Symptom:
    Once one of the alarm of rogue AP is deleted the newer rogue AP alarm changed to removed state even for different mac address.
    Because of the removed state the detecting AP which detected the rogue is not displayed
    Conditions:
    1) Auto SPT is turned on
    2) Prime 2.0 or 2.1
    Workaround:
    Click on refresh from network for each alarm in removed state or disable auto spt
    Last Modified:
    Jun 30,2014
    Status:
    Fixed
    Severity:
    3 Moderate
    Product:
    Cisco Prime Network Control System Series Appliances
    Known Affected Releases:
    (1)
    2.1(0.0.1)

  • Cisco Prime Collaboration Assurance IPPhone 3901 no serial number report

    Hi All,
    I have installed Cisco Prime Collaboration Assurance in my office and try to create phone inventory report , so far no problem , but when i add IPPhone 3901 there no serial number in the report , I have enable web access on the phone , i can see the serial number by click the IP  .
    any help ?
    Best Regards,
    Tommy

  • User Name and Password for Cisco Prime Infrastructure 2.1

    Hi all:
    I am stuck at the login page of Cisco Prime Infrastructure 2.1.
    I have tried using the user name root and its password (when log in with root at Vsphere Client) and also the login user name "before" get into the appliance infrastructure, all cannot work.
    Anybody knows what is the default username or password or any way to set the username and password for this Cisco Prime Infrastructure 2.1 website?
    Thanks!
    tangsuan

    Hi Tangsuan,
    Following is the documented procedure for password recovery..
    In order to modify the GUI root user password, you will need to login to the NCS CLI
    as an admin user, and enter the command
    "ncs password root password <new password>" (without the quotes)
    This should set the web interface root user password :
    http://www.cisco.com/en/US/docs/wireless/ncs/1.1/configuration/guide/manag.html#wp1268889
    If you have lost your CLI password , try the default logging that is  ,
    CLI user is admin and not root, so please try logging in as admin with
    the password that was set during setup. If that does not work , you need
    the install disk that came with the appliance to recover that password.
    Follow these steps:
    Recovering a Lost Admin Password
    If you lose or forget the admin password for NCS appliance, follow these steps.
    Step 1 Reboot the NCS appliance with the ISO DVD inserted. The Cisco Prime Network Control
    System Welcome screen appears:
    ISOLINUX 3.11 2005-09-02  Copyright (C) 1994-2005 H. Peter Anvin
                 Welcome to Cisco Prime Network Control System
    To boot from hard disk, press <Enter>.
    Available boot options:
       [1] Network Control System Installation (Keyboard/Monitor)
       [2] Network Control System Installation (Serial Console)
       [3] Recover administrator password. (Keyboard/Monitor)
       [4] Recover administrator password. (Serial Console)
    <Enter> Boot existing OS from Hard Disk.
    Enter boot option and press <return>.
    boot:
    Step 2 Select the desired recovery option, 3 or 4, depending on how you
    are connected to the appliance and then follow the prompts.
    Thanks-
    Afroz
    ***Ratings Encourages Contributors ****

  • Cisco Prime - Running LMS on a Windows PDC

    Greetings,
    Due to certain limitations we must run Cisco Prime on a Windows PDC (Primary Domain Controller).  This isn't supported, and the install/upgrade won't let you accomplish this, but I think on our Windows 2008 R2 Server Cisco Prime was originally installed on a stand-alone server that was later changed to a PDC.  We're running LMS 4.2.3 and it seems to run fine but now we need to upgrade but the installer won't allow it.  Has anyone out there come up with a workaround that allows you to run an upgrade on a PDC?
    Any clever ideas on how to circumvent this greatly appreciated!
    George

    I see better what you mean now I didn't associate AD with the windows domain.
    Yes I too had a customer where the LMS server down after it was "targeted" by a GPO from a policyserver.
    I was good for doing a reinstall of LMS until on of people of their network team found what policy clobbered the server. He could then revert the damage.
    Basically the server is best left alone as well as the casuser account.
    Actually the prefered situation from cisco is to take the machine out of the domain (standalone).
    Cheers,
    Michel

Maybe you are looking for

  • How do i use air sync to sync with my iTunes on my computer

    How do i use air sync to sync with my iTunes on my computer

  • Redeem a Code from a Blu-Ray Movie

    Can anyone help me or have any suggestions for the last month at least twice a day I've tried to redeem a code that I've gotten with the purchase of the Blu-Ray movie Parker. Every time that I've tried to redeem I'm getting this message when ever I'v

  • Permissions issues with Lion

    I just suddenly started having issues with my permissions with folders on external drives. Many of my folders (which appear to be random) no longer allow me to read or write them, and a dialog box appears saying I do not have permssion to access the

  • Restart of application neccessary?

    Hello, when I update a application written in ABAP/4 on R/3 platforms this updated version is autom. used for new users of the application but running instances could continue. What happend's in the Enterprise portal when I update a application (for

  • IPhoto - pictures not showing in full screen

    Hi, I'm using iPhoto and have uploaded my pictures from camera (one I've always used before and had success with).  The pictures load and I can see the thumnails, but when I switch to view in full screen the picture flashes up really quickly and is r


HashFlare