Cisco prime 4.2 monitor SFP conn & isdn active call session

Hello all,
my customer already bought cisco prime 4.2 , they asked me if this cisco prime is able to monitor the SFP (fiber connector) status active/not active and monitor the voice call active session for 24 hours ? anyone can help me to configure it ?
thanks in advance,

i couldn't find the appropriate MIB to monitor the call session

Similar Messages

  • Does Cisco Prime Infrastructure supports monitoring CPU,Memory, HDD for UCS , VMWare?

    Does Cisco Prime Infrastructure supports monitoring CPU,Memory, HDD for UCS , VMWare?

    Prime Infrastructure/ Assurance is  positioned today more towards managing network elements and network performance,  rather than server infrastructure. We are in the process of adding Datacenter  component support, with more focus on Nexus and UCS- due later this  year.
    Having said that, Prime Infrastructure allows the system user to  add custom SNMP polling templates, which can then be used for polling any SNMP  based values from any SNMP enabled device. These can be used to collect the  information you specified below and the polled information will be available in  dashboards and reports.

  • Cisco Prime LMS MPLS monitoring

    Hi all, have anyone used Cisco Prime LMS for MPLS xconnect monitoring?
    Currently when these traps arrive to Cisco Prime LMS they are classified as "InformAlarm Unidentified Trap Generic".
    Is it maybe possible to load the correct MIB for these traps and get Cisco Prime LMS to understand them correctly?
    The raw traps looks like this:
    xconnect down:
    09:58:42.352760 IP (tos 0x40, ttl 245, id 12, offset 0, flags [none], proto: UDP (17), length: 114) routerhost.51591 > lmshost.snmptrap: [udp sum ok]  { SNMPv1 { Trap(71)  E:cisco.10.106.2 10.130.1.13 enterpriseSpecific s=1 424011509 E:cisco.10.106.1.2.1.26.2=2 E:cisco.10.106.1.2.1.26.2=2 } }
    xconnect up:
    09:59:48.597894 IP (tos 0x40, ttl 245, id 14, offset 0, flags [none], proto: UDP (17), length: 114) routerhost.51591 > lmshost.snmptrap: [udp sum ok]  { SNMPv1 { Trap(71)  E:cisco.10.106.2 10.130.1.13 enterpriseSpecific s=2 424018144 E:cisco.10.106.1.2.1.26.2=1 E:cisco.10.106.1.2.1.26.2=1 } }
    I found some more info about the traps at:
    http://tools.cisco.com/Support/SNMP/do/BrowseMIB.do?local=en&step=2&mibName=CISCO-IETF-PW-MIB-V1SMI
    BR /Crille

    Here is an update:
    After discussing with TAC there seems to be 2 possible solutions in LMS right now:
    1. Create a threshold that monitors the specific OID for the xconnect vc and generate alarm if it changes.
    2. Configure the device to send syslog when a xconnect state changes and create an "automated syslog action".
    I have not tried either of them yet so I dont know which one works best, but option 2 seems easiest (its a one time config).

  • Monitoring the number of active calls in a gateway from HUM

    Hi,
    we are configuring HUM and we want to display the number of active calls in a gateway but we can't find any OID's that show exactly what we want. So we are going to use the EXPRESSION-MIB in order to calculate some values we need.
    In MRTG we launch a snmpwalk query against the OID 1.3.6.1.4.1.9.9.63.1.3.1.1.9 (cvCallActiveInSignalLevel) and we count with a counter the number of rows obtained from that snmpwalk. The calculation is as follows:
    @ret=snmpwalk(sigint03.'@'.'x.x.x.x'.'1.3.6.1.4.1.9.9.63.1.3.1.1.9');
    foreach $campo (@ret) {
         $cuenta=$cuenta+1;
    print $cuenta."\n";
    But we don't know how to implement the "foreach" loop with the EXPRESSION-MIB... and we don't know any other way for getting the number of active calls.
    Can anybody please help me?
    Regards.

    Hi, I've only changed the command:
    snmpset -v 2c -c private router expExpressionValueType i 4
    with:
    snmpset -v 2c -c private router expExpressionValueType.1 i 4
    and
    snmpset -v 2c -c private router expExpressionValueType.2 i 4
    because, an error message appeared if not using the index. So, finally, the commands used are the following:
    snmpset -v 2c -c private router expNameStatus.110.110.110.110.110 i 6snmpset -v 2c -c private router expNameStatus.110.110.110.110.110 i 5snmpset -v 2c -c private router expExpressionIndex.110.110.110.110.110 gauge 1snmpset -v 2c -c private router expExpressionComment.1 octetstring "numeroEntradas"snmpset -v 2c -c private router expExpression.1 octetstring '$1 >= 0'snmpset -v 2c -c private router expObjectID.1.1 o 1.3.6.1.4.1.9.9.63.1.3.1.1.1snmpset -v 2c -c private router expExpressionValueType.1 i 4snmpset -v 2c -c private router expObjectIDWildcard.1.1 i 1snmpset -v 2c -c private router expObjectStatus.1.1 i 1snmpset -v 2c -c private router expNameStatus.110.110.110.110.110 i 1snmpset -v 2c -c private router expNameStatus.111.111.111.111.111 i 6snmpset -v 2c -c private router expNameStatus.111.111.111.111.111 i 5snmpset -v 2c -c private router expExpressionIndex.111.111.111.111.111 gauge 2snmpset -v 2c -c private router expExpressionComment.2 octetstring "sumaEntradas"snmpset -v 2c -c private router expExpression.2 octetstring 'sum($1)'snmpset -v 2c -c private router expObjectID.2.1 o expValueInteger32Val.1.0.0snmpset -v 2c -c private router expExpressionValueType.2 i 4snmpset -v 2c -c private router expObjectIDWildcard.2.1 i 1snmpset -v 2c -c private router expObjectStatus.2.1 i 1snmpset -v 2c -c private router expNameStatus.111.111.111.111.111 i 1
    But there are no entries in the expValueInteger32Val OID, so later, in the sum expression, there is no elements to sum. Please, find attached 2 files with the snmpwalk outputs.
    How could we get to have values in expValueTable?
    Many thanks.

  • Cisco Prime Infrastructure 1.2 OVA - URL/FTP not working

    The ESXi install of the theNCS  OVA was successful. NCS seems to load and activate interfaces. The console session is working. Using compliant browsers; https://<ip address> does not work. When I stop "ncs" or halt the vm the web page responds shortly but then the connection is lost.  I used "show ports" and tried https://<ip address>/8082 and get a login from the Cisco Prime Infrastructure Health Monitor URL. There is a prompt for the authorization key. How can I confirm the installation is complte and all services are up and running
    Thanks
    Terry

    After digging almost 1 month, I found the answer.
    When you do provision from ESXi with ova file, you have to create "Thick Provision" otherwise, you wiil have same problem such as "some services are not up"
    In my case, I am running ESXi on the top of VM WorkStation since I don't have any ESXi server. When I added 250GB into the WorkStation and did provision with "Thick" it works !!! 
    Since my testing envrionment is little complicated (ESXi with VM WorkStation), I added first 250GB HDD into ESXi, and tried. It didn't work. So I added 250GB into VM WorkStation and did provision through Workstation, it worked (If you don't understand this statements, do not worry. If you have ESXi server, you don't need to worry about)
    As far as cisco ova is concerned, when I talked to one of my my friend who was working for new ACS (Virtual Appliance) he had same issue. He also solved with "Thick Provision"
    FYI, even if when I installed with "Thin Provision", PI 1.2 used only 10GB out of 200GB, so I did not think that I should use "Think Provision". But definitely not.

  • How to mornitor VSS (Virtual Switching System) & Stack (Switch) By Cisco Prime Infrastructure

    Dear all,
    I have 02 C6504-E with VSS (Virtual Switching System)
       and 02 C3750X-24T-L used Stack
    How to you Cisco Prime Infrastructure to monitor VSS & Stack tatus?
    Thanks.

    Virtual Switching technology is  the process of combining two standalone distribution switches found in  the local distribution layer into a single management point.
    The Virtual  Switching System functions and appears as a single switch to the wiring  closet and the core layer. You can also create Virtual Switching Systems  with a pair of standalone switches available in the core layer.
    For configuration please check  the below link:
    http://www.cisco.com/en/US/docs/net_mgmt/ciscoworks_lan_management_solution/4.1/user/guide/configuration/configvss.html#wp1042960

  • Question of Cisco Prime

    Hi everybody.
    I have one question about cisco prime infraestructure, i whish to know how the Cisco Prime control the link WAN of my enterprise.
    the topology is:
    ROUTER --> MODEM --> ISP
    I supossed that CP must have the assurance lincense, for use the control with netflow, but i whish to know how i can monitored the link between the modem and the ISP with the cisco prime.
    i can monitored the link with the soft. Intermapper, i whis to know if the Ciso Prime 1.2 could perform this action.
    Regards

    Well the situation is like this... I am monitoring several wireless network devices. Some are connected by 3G and others via some other technology.
    As you probably already know wireless connections are situational. Sometimes they work and sometimes they don't. What I want to achieve is to reduce the number of false positive alarms from these devices.
    The current plan is to increase the timeout to the maximum (60 seconds) and the number of retries to a high enough number to make false positives statistically unprobable.
    I would still like the devices to get polled quite often for a quick response, for example each 4 minutes (240 seconds).
    The optimal situation would be the following:
    Poll repeatedly each 4 minutes...
    For each successful poll, the timer resets and after 4 minutes another poll happens, except for when the poll is not successful. When this happens no new polling instances get started and the polling instance that failed continues with a timeout of 60 seconds for X number of repetitions.
    As soon as one of the retries is successful, the timer resets and in 4 minutes time a new polling instance gets created anew. If however after all of the retries, the device still fails to respond to the polls an alarm should get created and in 4 minutes time, it's time to check if the connectivity has been restored.
    Hopefully the image is a little clearer now... This is why I'm interested in understanding if new polling instances get started independently or not.

  • Cisco Prime 2.1, Removing Subgroup from Group in the Device Work Centre

    Hi All,
    I am having trouble removing a Device Group from within a Group in Cisco Prime.
    In short, there is a group called 'Cisco 3850 Series Ethernet Stackable Switch' which exists under both the 'Wireless Controller' group and the 'Switches and Hubs' group. I want to remove it from the 'Wireless Controllers' group as we are not using the controller functionality of the deivce.
    Can anyone help on this issue?
    Thanks,
    Cameron

    Hi TD,
    I would suggest you to take both the backup ::
    Application and appliance backups
    Prime Infrastructure creates two types of backups:
    Application backups: These contain all Prime Infrastructure application data, but do not include host-specific settings, such as the server hostname and IP address.
    Appliance backups: These contain all application data and host-specific settings, including the hostname, IP address, subnet mask, and default gateway.
    Note that:
    Application and appliance backups can be taken from both virtual and hardware appliances.
    Either type of backup can be restored to the same or a new host, as long as the new host has the same hardware and software configuration as the host from which the backup was taken.
    You can only restore an application or appliance backup to a host running the same version of the Prime Infrastructure server software as the server from which the backup was taken.
    You cannot restore an application backup using the appliance restore command, nor can you restore an appliance backup using the application backup command.
    refer the below links::
    http://www.cisco.com/c/en/us/td/docs/net_mgmt/prime/infrastructure/2-2/administrator/guide/PIAdminBook/backup_restore.html#10347
    http://www.cisco.com/c/en/us/td/docs/net_mgmt/prime/infrastructure/2-2/administrator/guide/PIAdminBook/backup_restore.html#72460
    Thanks-
    Afroz
    ***Ratings Encourages Contributors ****

  • Cisco Prime 2.0 Infrastructure-how to remove unneccessary interfaces from monitoring

    Hello all,
    We have Cisco Prime 2.0 Infrastructure and I would like to know how to remove certain interfaces from monitoring?  For example, I do not need monitoring on some ISDN and FXS/FXO ports.  I am receiving email alerts for ISDN channels going up/down for example.   Thanks.

    take a look at:::
    http://www.cisco.com/en/US/docs/net_mgmt/prime/infrastructure/2.0/user/guide/setup_groups.html

  • UPS monitoring support with Cisco Prime Infrastructure 1.2

    Dear Members,
    Good day,
    I am having a project implemented wherein i have the UPS power redudancy solution for our network devices.
    Now can anyone gide that is it possible for below :-
    UPS units installed with SNMP cards be monitored via Cisco Prime Infrastructure 1.2 as our monitoring & management solution is Cisco Prime Infrastructure 1.2 ?
    if yes
    Can you guide if following action would be possible to export the below logs from UPS unit to our Cisco Prime Infrastructure 1.2
       a) UPS fault status information
       b) UPS operational status(input power available Y/N)
       c) Battery fault status
       d) Battery charging current
       e) Battery charge level
       f) Output current
    Conclusion is we need to confirm that would it be posible to achieve remote monitoring of these UPS units via our CPI 1.2
    Thanks in Advance for your support & replies to this query.
    Regards,
    Muzammil N.

    Prime Infrastructure 1.2 can manage non-Cisco devices in a limited fashion via SNMP query and trap processing. It cannot import logs and does not have a generic syslog server,
    So if your devices have snmp read only support and can generate SNMP traps for the above you can add them to PI. Follow the manual add device procedure here.

  • Monitoring ASA in Cisco Prime infrastructure 2.2

    Hi everybody.  I have some issue with cisco Prime Infrastructure  2.2.  We use this product in our network for monitoring network devices and I need to monitor also our ASA 5550 device with soft 8.4.  I  added ASA to Cisco PI but see only basic component like my device can reachable via  and read via snmp. But cannot see  CPU, RAM, Device ENV like Temperature, l2l vpn connection,  Interfaces status and Utilization that interfaces, cannot see sub interface that placed on ASA like that g0/0.20.  I need fully monitor ASA and See logs and trap for my device:
    CPU RAM ENV (Temperature), Interface and sub interface status, L2L VPN  Status.
    1 Cisco Prime infrastructure can full support  ASA for monitoring and logging.. IF YES how can i configure  that features in Cisco PI 2.2 for ASA
    2 IF not which product Can full support that features for full monitoring and logging  ASA devices
    I have a little deadline for finishing
    thanks everybody before

    I've not success monitoring ASA interface utilization either. I'm using PI 2.2 with device update #1. The ASA is a 5585-X with 9.2(3) software.
    I have deployed the PI monitoring template to the ASA and do see its overall status and PI has enumerated the interfaces in the device page.
    I even looked at a packet capture and see PI querying the values of the interface counters and those values being sent back to PI - yet I cannot select any ASA interface when drilling down under Performance Detail monitoring.
    When I get some free time I will open a TAC case on it, meanwhile I am getting all the info I need from the upstream and downstream switches.

  • Can we Monitor third party Windows servers through Cisco Prime

    Hi Team,
    We are  using  Cisco Prime assurance and  are currently monitoring Cisco UCCE Components through it.
    Meanwhile we have   few third party  windows servers , which we would like to monitor it through Cisco Prime , just to maintain a single monitoring tool.
    If yes, please share the steps or link.Also highlight the limitations in that.
    Regards,
    krishna

    Seems Cisco Prime Assurance Manager is now obsolete and end of life already.
    It is replaced by Cisco Prime Infrastructure. CPI supports third party/vendor devices to some minimum extent with limited management details collected via SNMP Templates.
    -Thanks
    Vinod
    **Encourage Contributors. RATE Them.**

  • Cisco Prime LMS 4.1 - Monitoring events

    Dear all
    I have a problem to see the events in the Cisco Prime, for example when an event occurs (port-shutdown) in the switch I receive this information:
    Event Source
    DFM
    Description
    Cisco  Command Monitoring -> Event Command Source: Command Line, Event  Config Source: Running, Event Config Destination: Command Source
    Event Category
    Other
    Fault Last Updated At
    07-Mar-2013 16:57:40
    Event_Description
    InformAlarm
    Component
    192.168.10.5: Cisco Configuration Management Trap
    I don't see the details of the port that was done, or other deatiled that give aditional information abut the event. I have configured the Cisco Prime in this way:
    - Admin > Network > Notification and Action Settings > Event Sets  :   I have marked all the events
    - Admin> Network > Notification and Action Settings>Fault - Email notification : My mail is configured , I received alarms by mail.
    - Admin> Network > Notification and Action Settings>Fault Notification Group  : is configured
    Notification                      Group Name:
    TestSW4
    Device List:
    192.168.10.7 ; 192.168.10.6 ; 192.168.10.5 ; 192.168.10.253 ;
    Event Set:
    All
    Event Severity:
    Critical ; Warning ; Informational ;
    Event Status:
    Active ;
    Customer Identification:
    The snmp was configured in the devices:
    snmp-server system-shutdown
    snmp-server enable traps
    snmp-server community <community> RW
    snmp-server host 192.168.10.x <community>
    PLease your support or give some information to configure correctly the events and failures in cisco prime in order to see correctly

    Hi,
    This community is for collaboration. Pls post your question in the following community:
    Home --> NetPro --> Network Infrastructure --> Network Management --> Discussions
    Thanks,

  • Gestion con Cisco Prime LMS

                       Hola,
      Por favor, tengo un par de preguntas con el Cisco Prime LMS:
    Primero: Puedo monitorear equipos que no son de Cisco?
    Segundo: Puedo monitorear temperatura de loos equipos con LMS o debe ser Network?
    Gracias

    Cisco Prime LMS does NOT have the WAN QoS deployment capabilities packaged up nicely the way QPM did. It does, however, offer the Auto Smartports and MediaNet work centers that aid in setting up (primarily) endpoint switch ports. See this link for more details.
    I believe the best one could do with respect to MAN/WAN devices' QoS settings using LMS would be to create deployment templates and do compliance checks.

  • Cisco Prime Monitor Sub Interfaces

    We are currently running Cisco Prime 2.1 and trying to monitor sub interfaces on our Cisco 7606.  We can see the sub interfaces by:
    Operate | Device Work Center
    Select Quick Filter (to find the 7606)
    Select Interfaces
    Select IP Interfaces
    The sub interfaces that we wish to monitor are displayed (with the above steps).  However, when we try to select the interface to monitor, the sub interfaces do not appear:
    Home | Detail Dashboard
    Select Interface
    Select the interface pull-down | All | 7606
    We do not see the sub interfaces, only 2 interfaces are displayed.  We do not see the interface GigabitEthernet4/7 at all.  What are we missing here?

    i couldn't find the appropriate MIB to monitor the call session

Maybe you are looking for

  • I formatted my desktop. and now i have a fresh copy of firefox on my desktop. How can i use firefox sync to get all my history, passwords and add-ons

    I have a firefox sync account. I used to sync all my information and save it to Firefox server. Because of some reason i have to format my system and now i have a fresh copy of Firefox installed. Now i want to use sync to restore all my password,hist

  • java.io.File instance .list() not working properly

    i want to get the file, folders in any directory, so i used the File.list() method. but it is working in a peculiar manner. first see my simplified code, where the problem i am having:: public class FileChildTest {      public static void main(String

  • Word 2010 Send As Attachment does not send a HTML formatted mail

    Hi! I'm using Word 2010 to send a document by clicking File->Save & Send->Send Using E-mail->Send as Attachment. In the Outlook 2010  new message window I click the ribbon tab Format Text and then I select HTML as the message format. I continue to ha

  • Battery Mac book pro

    Hi! I bought a MacBook PRO 13" a month ago, and it's strange how the battery capacity is going down every time i have to charge it. for EX: I use it after i bought it and then made a full charge, and so on ( 6 cycles and did not left it go below 5-10

  • No Service

    Does any one know how to get service bk on a iPhone 4 Please, I can got 3G on and can get on the Internet but can't call out or recieve calls and can't send or recieve messages... Been like this for a while now