Cisco RV042 port forwording case?

Hello,
Here is my situation. I have two real IP addresses on each of my WAN ports. I need to configure:
port forwarding (80,443,3389) from Real_IP1 (configured on WAN1) to 192.168.116.10 (same ports)
port forwarding (80,443,3389) from Real_IP2 (configured on WAN2) to 192.168.117.10 (same ports)
Router is confugured in System Management > Dual WAN as Load balancing.
192.168.116.0 is in vlan1 (port1)
192.168.117.0 is in vlan2 (port2)
Is it possible to make it working using Cisco RV042?
Thanks in advance!

Plamen,
Try to create an Access Rule like shown in the following example. On the second rule, select WAN 2 and use the other internal IP. I have never tested this but it looks like it might be a solution. (This is an older RV042)
Please let us know if this works or not.
- Marty

Similar Messages

  • Port forwarding Cisco RV042 / RV042G

    Hi,
    we use three Cisco RV042 small Business Routers.
    The problem:
    We want to forward HTTPS on Wan-side to an other port than 443 on Lan-side.
    For example: Wan 217.44.55.66 port 443 to 192.168.0.5 port 5001
    There is only this option in RV042 : Forwarding -> Service HTTPS [TCP/443~443] to "IP-Adress" (also Port 443)
    but we need something like this:
    Forwarding -> Service HTTPS [TCP/443~443] to 192.168.0.5:5001
    How can I configure it ?
    Greetings from Germany
    Goetz Hartwig, ITUC GmbH

    Hi Ituconsult1
    My name is Mehdi from Cisco Technical Support, yes with RV042 we can translate the port 
    Please follow this steps:
    1. Please remove the rule of the port forwarding 
    2. Go to Setup under UPnP , service management and you will see external port and internal port so please configure external port to 443 and internal to 5001 and click add, please do not enable UPnP
    3. on the same page please choose the service you created and put the internal IP of the server server
    Please rate the post or mark it as answered to help other Cisco customers
    Greeting 
    Regards
    Mehdi

  • Need Help Setup Cisco RV042 vpn

    good day everyone, a month ago my boss purchase 4 pcs cisco rv042 vpn to be used in our small office and to our satelite office, with expectations of simple file sharing and remote troubleshooting and for better and safe data transfer. since the task is given to me as an IT staff it is difficult to me to setup this vpn router since i have a little  idea and many question are on my mind that need to be answered, i read the manual test the vpn router but still no good answered found. i know it is dufficult but with proper guide and step by step on how to use this one i can make it work. please anyone help me i need answers to this questions.
    i am using windows 7 pro sp1 64bit for my test unit, how can i make a vpn server? a client?
    in the past i connect the internet connection in the internet connection port in the back of the router, then another cable from vpn port 1-4 i select #4 port to connect to my pc, since the vpn give the ip on my pc i can easily connect to the firmware of the vpn using the deafault username and password. when i go to the firmware i dont know where to start, and i dont even have the internet connection for my pc.
    i feel sorry for myself beacuse i have no idea in this kind of thing, CISCO people and others out there i am calling for your help.
    thank you in advance
    mel

    Dear Emilio,
    Thank you for reaching Cisco Small Business Support Community.
    If you’d like to setup a Site to Site VPN on your RV042 here is a good step by step guide;
    http://sbkb.cisco.com/CiscoSB/Loginr.aspx?login=1&pid=2&app=search&vw=1&articleid=304
    If you are looking into a remote access VPN, QuickVPN, here is the step by step procedure;
    http://sbkb.cisco.com/CiscoSB/Loginr.aspx?login=1&pid=2&app=search&vw=1&articleid=452
    Just in case here is also a document with Windows operating systems tips;
    http://sbkb.cisco.com/CiscoSB/Loginr.aspx?login=1&pid=2&app=search&vw=1&articleid=2922
    Finally here is a link with the Admin Guide where starting on page 122 you can find everything related to VPN setup on this particular device model, beside info in how to setup your internal network (I suggest you to go through this admin guide so you know everything about the router);
    http://www.cisco.com/en/US/docs/routers/csbr/rv0xx/administration/guide/rv0xx_AG_78-19576.pdf
    Please let me know if there is any further assistance we may assist you with.
    Kind regards,
    Jeffrey Rodriguez S. .:|:.:|:.
    Cisco Customer Support Engineer
    *Please rate the Post so other will know when an answer has been found.

  • Does Solaris 10 support cisco Virtual Port Channels over IP?

    Does anyone know if Solaris 10 support cisco Virtual Port Channels open IP?

    Hi user11114413,
    The issue you are seeing actually has little to do with VIP, and more to do with there being multiple IP addresses for us to choose from on your box. For such multi-IP boxes, you'll want to tell us the IP to use, and in your case you want to tell as a VIP. This can be done either by editing your operational configuration file, and including an <address> element within the <unicast-listener> element, or via the tangosol.coherence.localhost system property. For example:
    <unicast-listener>
        <well-known-addresses>
            <socket-address id="1">
                <address>1.2.3.260</address> <!--virtual ip -->
                <port>8088</port>
            </socket-address>
        </well-known-addresses>
        <address>1.2.3.260</address> <!--virtual ip -->
        <port>8088</port>
    </unicast-listener>or
    java ... -Dtangosol.coherence.localhost=1.2.3.260If you are using the same operational configuration on all nodes in your cluster then the system property approach is likely preferable, and would only be necessary on the two machines sharing the VIP.
    As for using VIP or an extended WKA list, the choice is yours, either will work. If you do go the VIP route, it would obviously be a very bad idea to simultaneously use the same VIP and port at the same time from the two machines.
    thanks,
    Mark
    Oracle Coherence

  • Cisco rv042 not forwarding

    Hello my Name is Enoth Rojas from the republic of Panama.
    I have a dual band cisco rv042 router which does not respond to port forwarding for remote desktop. When I check from the internet for open ports it says that port 3389 is close. I have been unable to make it forward the request. Any advice will be appreciate?
    Thanks
    Enoth Rojas

    Hello enothrojas,
    If you check the logging and enable all the logging for accepted connections.  Once this is enabled attempt to RDP to the computer you want access to, make sure your not on the local network when you attempt for better testing.  Then go to your logging and then look at your incoming logs.
    Look for the source IP address, (the WAN IP address of the site you attempted the connection from) and see if the RV042 is seeing the request.
    If it is not then you will need to talk to your ISP.  If it is, what is the destination?
    Then look at your outgoing log table and see if you see an ACK being sent back to your source, if it is not then the PC you are trying to access is no replying.
    Hope this helps.
    Regards,
    Michael D.

  • Load balancing on cisco rv042

    Hi friends,
    This is regarding I am facing issue with configuring the load balancing in cisco rv042 .I had configured the load balancing between dual wan of leased line and adsl coonection but loadbalancing is not working fine kindly help me on this

    If i close one link it takes 20 seconds of downtime and then ping goes without loses.
    In the end i decided to go with PBR, since the deadline for our project was surpassed.
    I set up acl that matched every other 32 adress block:
        10 permit ip 192.168.100.32 0.0.0.31 any 
        20 permit ip 192.168.100.96 0.0.0.31 any 
        30 permit ip 192.168.100.160 0.0.0.31 any 
        40 permit ip 192.168.100.224 0.0.0.31 any
        50 deny ip any any
    Set a route map that sends that traffic trough one of the interfaces (Gi0/1) and let routing do the rest:
    track 1 interface dialer 0 line-protocol
    ip route 0.0.0.0 0.0.0.0.0 Dialer0 track 1
    ip route 0.0.0.0 0.0.0.0.0 GigabitEthernet0/1 10
    Its not exactly what i wanted but its close enough:) 
    Thanks for your advices.

  • PPTP Not Working On Ipad Thru Cisco RV042

    I have an Ipad 1,
    a Linksys RV042 At My Office
    And a Cisco RV042 at my Home
    However I'm Creating PPTP Connection on my Ipad For Both VPN , Office is Connection, but Home is not Connecting...
    I tried to connect to Home Thru any PC, And It is Working...
    Any Issues With Ipad and Cisco Firmwares and Softwares? Can Please Somebody Help in here... 

    Hi Semaan ,
    since this question is about a product in the Cisco Small Business / Linksys range, I suggest you move it to the community, where you will have a better chance of getting expert advice.
    best regards,
    Herbert
    Cisco Moderator

  • Cisco RV042 - Dual Wan Load Balancing - Secure Site (HTTPS) Trouble

    PID VID :
    RV042 V03
    Firmware Version :
    v4.0.0.07-tm (Aug 19 2010 19:19:50)
    Ever since I setup my RV042 with load balancing using the Dual Wan system I have had trouble staying connected to some secure sites. After doing some searching I found that the potential issue is the IP change mid session.
    "http://www.broadbandreports.com/forum/r25537589-Cisco-RV042-can-not-use-load-balancing-for-some-web-sites"
    Although my interface is significantly different I was able to find the same area in my RV042 admin area however, it doesn't seem to work.
    System Management
    > Dual Wan
    In Wan 1 & Wan 2 I have HTTPS and HTTPS Secondary all forwarded to use Wan 2 under Protocol Binding
    This however has not managed to do anything at all for my network and every computer conneceted experiences the same HTTPS irregularities at some websites.
    I'm sure I must be doing something wrong, but I don't know what it is.
    Both incoming connections are from the same service provider although the plans are different.
    Any help with this would greatly help me stop losing my mind trying to fight with my website control panel for 10 minutes to just login and get something done.
    Thanks

    Any ideas or advice from anyone?

  • How to search/Scan Vlan of cisco switch ports

    Can any one tell me how i can scan/search vlans of cisco switch port through any monitoring tool (orion/solarwinds).
    Consider this scenario as i have no access to switch and i want to know below things:
    1-Vlans created on switch?
    2-which switch port belongs to which vlan id?
    Thanks

    Hi,
    You can do it only with hub in between and also please note that when sniffing with Wireshark on Windows the OS would remove VLAN tag so you may need to use Linux machine.
    Regards,
    Aleksandra

  • Cisco RV042 VPN unable to connect to Netgear PS FVS318

    Hello,
    We recently replaced one of two Netgear ProSafe VPN FVS318 with a Cisco RV042 VPN. Both Netgear were configured site-site and was working fine until one of them failed. We copied as much configuration settings from the failed Netgear PS to the RV042 but were unsuccessful in establishing a connection between the two sites.
    The logs on the Cisco router shows this:
    VPN Log packet from 1.1.1.1:500: received Vendor ID payload [RFC 3947]  
    VPN Log packet from 1.1.1.1:500: ignoring Vendor ID payload [439b59f8ba676c4c7737ae22eab8f582]  
    VPN Log packet from 1.1.1.1:500: ignoring Vendor ID payload [439b59f8ba676c4c7737ae22eab8f582]  
    VPN Log packet from 1.1.1.1:500: ignoring Vendor ID payload [draft-ietf-ipsec-nat-t-ike-03]  
    VPN Log packet from 1.1.1.1:500: ignoring Vendor ID payload [draft-ietf-ipsec-nat-t-ike-03]  
    VPN Log packet from 1.1.1.1:500: ignoring Vendor ID payload [draft-ietf-ipsec-nat-t-ike-02_n]  
    VPN Log packet from 1.1.1.1:500: ignoring Vendor ID payload [draft-ietf-ipsec-nat-t-ike-02_n]  
    VPN Log packet from 1.1.1.1:500: [Tunnel Negotiation Info] <<< Responder Received Main Mode 1st packet  
    VPN Log packet from 1.1.1.1:500: [Tunnel Negotiation Info] <<< Responder Received Main Mode 1st packet  
    VPN Log packet from 1.1.1.1:500: initial Main Mode message received on 2.2.2.2:500 but no connection has been authorized with policy=PSK  
    Each time we select a tunnel test connect, that last message appears with "but no connection has been authorized with policy=PSK"
    *replaced actual IP with sample IP.
    Any ideas why this is happening?
    Thank you!

    Hello,
    It looks as RV042 receive phase 1 configuration from Netgear, but due to mismatch with it's phase 1 settings does not reply back.
    I can't be more specific as this could be anything in phase 1 - aggressive/main mode; the WAN IP addresses, encryption or SA lifetime. As well if any of the devices is behind NAT, the option NAT traversal should be checked.
    Regards,
    Kremena

  • Subred Para Cisco RV042

    hola buena tarde;
    A ver si me puedan ayudar con este problemita que tengo de antemano gracias.
    me están solicitando hacer una subred con 2 ciscos RV042, para que quede de la siguiente manera:
    red 1
    192.168.2.XXX, 255.255.255.0, 192.168.2.1 (Proveedor de Internet Telmex)
    red 2
    192.168.2.XXX, 255.255..255.0, 192.168.2.2 (Proveedor de Internet Axtel)
    estos routers están a una distancia como de 100 metros y los estoy enlazando con UTP , cada uno debe tener su propio servicio de internet;
    estuve buscando algún manual o algo que me pudiese ayudar pero hasta la fecha no eh encontrado.
    saludos.

    Que pena que no habia podido contestar pero estaba extremadamente ocupado.
    Lo importante es que trate de configurar esto en nuestro laboratorio y pude hacer que las dos redes hablaron pero aparecieron problemas importantes que me gustaria discutir.
    1- Tener los dos routers en la misma red (192.168.2.x) es una mala idea ya que el trafico puede perderse entre los dos routers.
    2- La comfiguracion que yo hice era connectando los dos dispositivos justos usando un cable UTP dee LAN a LAN. Un router tenia una direccion de 10.10.10.1 y el otro estaba en 192.168.1.1. Luego habilite la opcion de multple subnets Y adicione la red contraria en la tabla. por ejemplo, en el router con direccion IP 10.10.10.100 adicione una subnet para 192.168.1.1 y viceversa
    Usando este sistema, puede hacer que la dos redes se comunicaran y tuvieran diferentes direcciones IP, desafortunadamente computadoras connectadas directamente al router 10.10.10.1 podian recibir direcciones IP del otro router y viceversa.Lo que definitivamente es un problema.
    Pero si usted no esta usando DHCP para los computadores sino que estan configurados todos manualmente (o si quiere configurarlos todos manualmente) entionces si puede funcionar
    La opcion que yo veo que puede funcionar, pero definitivamente seria mas lenta es establecer una conexion via VPN en ambos routers.
    Por favor, dejeme saber que decide hacer.

  • Cisco RV042 bloqueo de navegación

    Quisiera saber si es posible bloquear toda la navegacion por internet excepto 2 o 3 paginas que yo disponga en un Cisco RV042.
    Solo veo la opcion de permitir todo y bloquear por lista.Yo necesito lo contrario, bloquear todo y permitir por lista.

    Hi Rafael,
    Regarding RV042 we cannot block the https traffic , you can ask for other model such a ISA550 or ISA570 Firewall router  which they have a security service and you can able to block https traffic also you can block by categories ....
    Here is the link for Emulator (please open it with IE or Firefox):
    https://www.cisco.com/assets/sol/sb/ISA500_Emulators/ISA500_Emulator_v1.1.13-1.2.1/index.htm
    Please rate the post or mark as answered to help other Cisco Customers
    Regards
    Mehdi

  • ¿Cómo enlazar dos site por medio de VPN utilizando un Cisco RV042?

    Hola amigos, tengo el siguiente escenario y necesito saber si es posible de implementar utilizando un Cisco RV042. Necesito comunicar dos sites utilizando un RV042 como equipo intermedio. Para tales efectos se require levantar un VPN entre el Site 1 y el punto central (donde está el RV042) y luego otro VPN entre el punto central y el Site 2. Ya ambos túneles están configurados y están activos, pero cuando trato de pasar paquetes entre el site 1 y el site 2, los paquetes se quedan en el RV042.
    Es posible solventar el problema? 

    Buenas,
    Señor su caso puede depender de muchas cosas diferentes y su explicacion de el problema es un poco opaco, seria mejor si nos llamara directamente al 1-800-606-1866 a nuestro centro tecnico donde podriamos crearle un caso y en vase de control remoto ver sus configuraciones y comparalas lado a lado para poder
    ver con mas precision lo que succede.  Segun entiendo su problema es que no puede configurar mas de un tunel entre los tres routers y necesita uno mas? si es
    asi hay una option detro de el firewal que tiene que abilitar para que mas de un tunel pueda se configurado a la misma ves, la opcion se llama multicast passthrough y tiene que estar en el modo enabled. El programa si existe y puede ser bajado de nuestra pagina web www.cisco.com en la bara de busqueda ponga el modelo del dispositivo RVS4000 y el primer resultado de la busqueda entre ahi, adentro encontrara informacion basica, un video demostrando el producto y una seccion que dice download firmware and documentation    oprima ahi y bajara un folder con varias cosas incluyendo el wizard para hacer site-site. 
    Tambien observo que las key life times estan incorrectos PHASE 1, el maximo puede ser 28800,  en PHASE 2 el maximo puede ser 3600  no puede cambiar estos valores ya que no va mas alto que eso. Es recomdable dejar estos valores en factory default.
    Saludos,
    Juan

  • Linksys WRT54G Port Forwording Promblem,

    ok im sure theres prombably a million of these but it seems everytime i try to port forword it dosent work, cuz i wanna run a Private server, so how can i portforword and i can tell this by, if i put my ip in the server it dosent connect so suggestion ideas? ohh and im try to do port 90 and my isp is comcast -Thankz for any help h00psO6

    If it is an issue with the Port forwarding ... check the firmware on the router ....
    if required upgrade the firmware .....

  • Cisco iron port feature activation code error how to resolve that?

    cisco iron port feature activation code error  how to resolve that?

    I have fixed this problem successfully.
    The problem was with the referral attribute of the cfldap tag.
    After adding this (referral="yes") attribute to my code I am able to login into my website.
    <cfldap action="QUERY" server="#application.LDAPServer#" port="#application.LDAPPort#" start="#application.LDAPBase#" name="search" attributes="alias, dn, uid, technicalCareerLevel, locationorgunit, givenName, sn" filter="#filter#" scope="SUBTREE" maxRows="2" referral="yes">
    Any way thanks for your assistance!!!!!

Maybe you are looking for