Cisco SIP Phone 9971 won't register on CME 8.6 or 8.5 Please HELP
Please help me , I have problem with registering Cisco SIP phone 9971 with CME 8.6 on ISR 2901.
I configured CME for SIP clients, then I add configuration for 9971 phone and create profiles. Phone downloaded SEP...xml file from CME,after that phone look for g4-tones.xml and gd-sip.jar files, I added them to CME after that phone downloaded them and reboot. Now phone is stuck in some kind of loop and does not register on CME.
On phone log I can see repeting next few messeges.
12:01:58a No DNS Server IP
12:01:59a Updating Trust list
12:01:59a No Trust List instaled
12:01:59a SEP04C5AB03B0D.cnf.xml (TFTP) // at this time phone download SEP...xml file from CME
12:02:00a VPN Error: VPN is not Configured
on CME if issue DEBUG TFTP EVENTS i receive next few lines
*Aug 18 18:20:19.891: TFTP: Looking for CTLSEP04C5A4B03B0D.tlv
*Aug 18 18:20:19.987: TFTP: Looking for ITLSEP04C5A4B03B0D.tlv
*Aug 18 18:20:20.083: TFTP: Looking for ITLFile.tlv
*Aug 18 18:20:20.347: TFTP: Looking for SEP04C5A4B03B0D.cnf.xml
*Aug 18 18:20:20.351: TFTP: Opened flash:/SEP04C5A4B03B0D.cnf.xml, fd 14, size 4585 for process 141
*Aug 18 18:20:20.363: TFTP: Finished flash:/SEP04C5A4B03B0D.cnf.xml, time 00:00:00 for process 141
here you can see verison info of CME
Cisco IOS Software, C2900 Software (C2900-UNIVERSALK9-M), Version 15.1(4)M, RELEASE SOFTWARE (fc1)
Technical Support: http://www.cisco.com/techsupport
Copyright (c) 1986-2011 by Cisco Systems, Inc.
Compiled Thu 24-Mar-11 15:31 by prod_rel_team
ROM: System Bootstrap, Version 15.0(1r)M9, RELEASE SOFTWARE (fc1)
ELTOSAN_ROUTER uptime is 1 hour, 50 minutes
System returned to ROM by reload at 16:29:20 UTC Thu Aug 18 2011
System image file is "flash:/c2900-universalk9-mz.SPA.151-4.M.bin"
Last reload type: Normal Reload
Last reload reason: Reload Command
Cisco CISCO2901/K9 (revision 1.0) with 471040K/53248K bytes of memory.
Processor board ID FGL1508252Y
3 Gigabit Ethernet interfaces
2 terminal lines
1 Virtual Private Network (VPN) Module
4 Voice FXO interfaces
4 Voice FXS interfaces
1 Internal Services Module (ISM) with Services Ready Engine (SRE)
Survivable Remote Site Voicemail (SRSV) on Cisco Unity Express (CUE) 8.5.1 in slot/sub-slot 0/0
DRAM configuration is 64 bits wide with parity enabled.
255K bytes of non-volatile configuration memory.
254464K bytes of ATA System CompactFlash 0 (Read/Write)
License Info:
License UDI:
Device# PID SN
*0 CISCO2901/K9 xxxxxxxxxxxxx
Technology Package License Information for Module:'c2900'
Technology Technology-package Technology-package
Current Type Next reboot
ipbase ipbasek9 Permanent ipbasek9
security securityk9 Permanent securityk9
uc uck9 Permanent uck9
data None None None
Configuration register is 0x2102
this is RUNNING CONFIGURATION
! Last configuration change at 16:10:12 UTC Thu Aug 18 2011
version 15.1
service timestamps debug datetime msec
service timestamps log datetime msec
no service password-encryption
hostname ELTOSAN_ROUTER
boot-start-marker
boot system flash:/c2900-universalk9-mz.SPA.151-4.M.bin
boot-end-marker
no aaa new-model
no ipv6 cef
ip source-route
no ip routing
no ip cef
no ip dhcp use vrf connected
ip dhcp excluded-address 192.168.5.1 192.168.5.10
ip dhcp excluded-address 192.168.5.200 192.168.5.255
ip dhcp pool phone
network 192.168.5.0 255.255.255.0
default-router 192.168.5.251
option 150 ip 192.168.5.251
ip dhcp pool data
relay source 192.168.2.0 255.255.255.0
relay destination 192.168.2.201
multilink bundle-name authenticated
crypto pki token default removal timeout 0
voice-card 0
voice service voip
allow-connections h323 to h323
allow-connections h323 to sip
allow-connections sip to h323
allow-connections sip to sip
supplementary-service h450.12
fax protocol pass-through g711alaw
sip
registrar server expires max 3600 min 120
voice register global
mode cme
source-address 192.168.5.251 port 5060
max-dn 6
max-pool 6
load 9971 sip9971.9-1-1SR1.loads
authenticate register
tftp-path flash:
create profile sync 0005135312289902
voice register dn 1
number 207
allow watch
name GossaVM
label 207
voice register dn 3
number 101
name Dejan
label 101
mwi
voice register pool 1
id mac 000C.29C5.0011
number 1 dn 1
dtmf-relay sip-notify
username testvm password testera
codec g711alaw
voice register pool 3
id mac 04C5.A4B0.3B0D
type 9971
number 3 dn 3
presence call-list
dtmf-relay rtp-nte
username dejan password 1234
codec g711alaw
no vad
license udi pid CISCO2901/K9 sn xxxxxxxxxxxx
hw-module ism 0
hw-module pvdm 0/0
redundancy
interface GigabitEthernet0/0
description INTERFACE INTERNAL
no ip address
no ip route-cache
duplex auto
speed auto
no mop enabled
interface GigabitEthernet0/0.2
description LAN DATA
encapsulation dot1Q 2
ip address 192.168.2.251 255.255.255.0
no ip route-cache
interface GigabitEthernet0/0.5
description LAN VOICE
encapsulation dot1Q 5
ip address 192.168.5.251 255.255.255.0
no ip route-cache
interface ISM0/0
no ip address
no ip route-cache
shutdown
!Application: SRSV-CUE Running on ISM
interface GigabitEthernet0/1
no ip address
no ip route-cache
shutdown
duplex auto
speed auto
interface ISM0/1
description Internal switch interface connected to Internal Service Module
shutdown
interface Vlan1
no ip address
no ip route-cache
shutdown
ip forward-protocol nd
no ip http server
no ip http secure-server
snmp-server community public RO
tftp-server flash:dkern9971.100609R2-9-1-1SR1.sebn alias dkern9971.100609R2-9-1-1SR1.sebn
tftp-server flash:kern9971.9-1-1SR1.sebn alias kern9971.9-1-1SR1.sebn
tftp-server flash:rootfs9971.9-1-1SR1.sebn alias rootfs9971.9-1-1SR1.sebn
tftp-server flash:sboot9971.031610R1-9-1-1SR1.sebn alias sboot9971.031610R1-9-1-1SR1.sebn
tftp-server flash:skern9971.022809R2-9-1-1SR1.sebn alias skern9971.022809R2-9-1-1SR1.sebn
tftp-server flash:sip9971.9-1-1SR1.loads alias sip9971.9-1-1SR1.loads
tftp-server flash:United_States/g4-tones.xml
tftp-server flash:English_United_States/gd-sip.jar
control-plane
voice-port 0/0/0
voice-port 0/0/1
voice-port 0/0/2
voice-port 0/0/3
voice-port 0/1/0
voice-port 0/1/1
voice-port 0/1/2
voice-port 0/1/3
mgcp profile default
gatekeeper
shutdown
line con 0
line aux 0
line 67
no activation-character
no exec
transport preferred none
transport input all
transport output pad telnet rlogin lapb-ta mop udptn v120 ssh
stopbits 1
line vty 0 4
password jebiga
login
transport input all
end
I did not have any kind of problem with X-LITE to register to CME. also try with few SCCP phones 7940 and I did not any kind of problem .
this is content of SEP....xml file for 9971
<device>
<deviceProtocol>SIP</deviceProtocol>
<devicePool>
<dateTimeSetting>
<dateTemplate>M/D/YA</dateTemplate>
<timeZone>Pacific Standard/Daylight Time</timeZone>
<ntps>
<ntp priority="0">
<name>0.0.0.0</name>
<ntpMode>unicast</ntpMode>
</ntp>
</ntps>
</dateTimeSetting>
<callManagerGroup>
<members>
<member priority="0">
<callManager>
<ports>
<sipPort>5060</sipPort>
</ports>
<processNodeName>192.168.5.251</processNodeName>
</callManager>
</member>
</members>
</callManagerGroup>
</devicePool>
<sipProfile>
<sipProxies>
<registerWithProxy>true</registerWithProxy>
</sipProxies>
<sipCallFeatures>
<cnfJoinEnabled>true</cnfJoinEnabled>
<localCfwdEnable>true</localCfwdEnable>
<callForwardURI>service-uri-cfwdall</callForwardURI>
<callPickupURI>service-uri-pickup</callPickupURI>
<callPickupGroupURI>service-uri-gpickup</callPickupGroupURI>
<callHoldRingback>2</callHoldRingback>
<semiAttendedTransfer>true</semiAttendedTransfer>
<anonymousCallBlock>2</anonymousCallBlock>
<callerIdBlocking>2</callerIdBlocking>
<dndControl>2</dndControl>
<remoteCcEnable>true</remoteCcEnable>
</sipCallFeatures>
<sipStack>
<remotePartyID>true</remotePartyID>
</sipStack>
<sipLines>
<line button="1" lineIndex="1">
<featureID>9</featureID>
<featureLabel></featureLabel>
<proxy>USECALLMANAGER</proxy>
<port>5060</port>
<name></name>
<displayName></displayName>
<autoAnswer>
<autoAnswerEnabled>2</autoAnswerEnabled>
</autoAnswer>
<callWaiting>1</callWaiting>
<authName>dejan</authName>
<authPassword>1234</authPassword>
<sharedLine>false</sharedLine>
<messagesNumber></messagesNumber>
<ringSettingActive>5</ringSettingActive>
<forwardCallInfoDisplay>
<callerName>true</callerName>
<callerNumber>true</callerNumber>
<redirectedNumber>true</redirectedNumber>
<dialedNumber>true</dialedNumber>
</forwardCallInfoDisplay>
</line>
<line button="2" lineIndex="2">
<featureID>9</featureID>
<featureLabel>101</featureLabel>
<proxy>USECALLMANAGER</proxy>
<port>5060</port>
<name>101</name>
<displayName>Dejan Rakic</displayName>
<autoAnswer>
<autoAnswerEnabled>2</autoAnswerEnabled>
</autoAnswer>
<callWaiting>1</callWaiting>
<authName>dejan</authName>
<authPassword>1234</authPassword>
<sharedLine>false</sharedLine>
<messagesNumber></messagesNumber>
<ringSettingActive>5</ringSettingActive>
<forwardCallInfoDisplay>
<callerName>true</callerName>
<callerNumber>true</callerNumber>
<redirectedNumber>true</redirectedNumber>
<dialedNumber>true</dialedNumber>
</forwardCallInfoDisplay>
</line>
</sipLines>
<enableVad>true</enableVad>
<preferredCodec>g711alaw</preferredCodec>
<dialTemplate></dialTemplate>
<kpml>1</kpml>
<phoneLabel></phoneLabel>
<stutterMsgWaiting>2</stutterMsgWaiting>
<disableLocalSpeedDialConfig>true</disableLocalSpeedDialConfig>
<dscpForAudio>184</dscpForAudio>
<dscpVideo>136</dscpVideo>
</sipProfile>
<commonProfile>
<phonePassword>1234</phonePassword>
<callLogBlfEnabled>2</callLogBlfEnabled>
</commonProfile>
<featurePolicyFile>featurePolicyDefault.xml</featurePolicyFile>
<loadInformation>sip9971.9-1-1SR1.loads</loadInformation>
<vendorConfig>
</vendorConfig>
<commonConfig>
<videoCapability>0</videoCapability>
<ciscoCamera>0</ciscoCamera>
</commonConfig>
<sshUserId>dejan</sshUserId>
<sshPassword>1234</sshPassword>
<userId></userId>
<phoneServices>
<provisioning>2</provisioning>
<phoneService type="1" category="0">
<name>Missed Calls</name>
<phoneLabel></phoneLabel>
<url>Application:Cisco/MissedCalls</url>
<vendor></vendor>
<version></version>
</phoneService>
<phoneService type="1" category="0">
<name>Received Calls</name>
<phoneLabel></phoneLabel>
<url>Application:Cisco/ReceivedCalls</url>
<vendor></vendor>
<version></version>
</phoneService>
<phoneService type="1" category="0">
<name>Placed Calls</name>
<phoneLabel></phoneLabel>
<url>Application:Cisco/PlacedCalls</url>
<vendor></vendor>
<version></version>
</phoneService>
<phoneService type="2" category="0">
<name>Voicemail</name>
<phoneLabel></phoneLabel>
<url>Application:Cisco/Voicemail</url>
<vendor></vendor>
<version></version>
</phoneService>
</phoneServices>
<versionStamp>0131511014412102</versionStamp>
<userLocale>
<name>English_United_States</name>
<langCode>en</langCode>
</userLocale>
<networkLocale>United_States</networkLocale>
<networkLocaleInfo>
<name>United_States</name>
</networkLocaleInfo>
<authenticationURL></authenticationURL>
<directoryURL></directoryURL>
<servicesURL>http://192.168.5.251:80/CMEserverForPhone/serviceurl</servicesURL>
<dscpForSCCPPhoneServices>0</dscpForSCCPPhoneServices>
<dscpForCm2Dvce>96</dscpForCm2Dvce>
<transportLayerProtocol>2</transportLayerProtocol>
</device>
Hello,
I'm facing exactly the same problem, that is:
a Cisco SIP Phone 9971 won't register on CME 8.6 running on a 2811
I have read all the postings to this Forum, but I have not been able to solve it.
In my case the commands voice register dn and voice register pool are OK.
So frankly, I have no idea what I could be missing.
I'm pasting the Router's config.
I hope somebody is able to point me in the right direction.
Here is the config. Thank you!
C2811#sh run
Building configuration...
version 15.1
service timestamps debug datetime msec
service timestamps log datetime msec
no service password-encryption
hostname C2811
no aaa new-model
dot11 syslog
ip source-route
ip cef
ip dhcp excluded-address 172.25.140.1 172.25.140.10
ip dhcp excluded-address 172.35.140.1 172.35.140.10
ip dhcp pool Data
network 172.25.140.0 255.255.255.0
default-router 172.25.140.1
option 150 ip 172.25.140.1
dns-server 172.25.140.1
ip dhcp pool Voice
network 172.35.140.0 255.255.255.0
default-router 172.35.140.1
option 150 ip 172.35.140.1
dns-server 172.35.140.1
no ip domain lookup
no ipv6 cef
multilink bundle-name authenticated
voice service voip
allow-connections sip to sip
sip
registrar server expires max 3600 min 120
voice register global
mode cme
source-address 172.25.140.1 port 5060
max-dn 40
max-pool 42
load 9971 sip9971.9-4-1-9.loads
authenticate register
authenticate realm cisco
tftp-path flash:
create profile sync 0004820400584603
voice register dn 1
number 1010
allow watch
name Phone10
label Phone10
mwi
voice register pool 1
id mac 189C.5DB6.BD09
type 9971
number 1 dn 1
presence call-list
dtmf-relay rtp-nte
username adm password adm
call-forward b2bua busy 68600
codec g711ulaw
no vad
camera
video
voice-card 0
crypto pki token default removal timeout 0
crypto pki trustpoint TP-self-signed-1879153754
enrollment selfsigned
subject-name cn=IOS-Self-Signed-Certificate-1879153754
revocation-check none
rsakeypair TP-self-signed-1879153754
crypto pki certificate chain TP-self-signed-1879153754
certificate self-signed 01
(details ommited)
license udi pid CISCO2811 sn FTX1146A44H
username admin privilege 15 password 0 admin
redundancy
interface FastEthernet0/0
no ip address
duplex auto
speed auto
interface FastEthernet0/0.25
description Data VLAN
encapsulation dot1Q 25
ip address 172.25.140.1 255.255.255.0
interface FastEthernet0/0.35
description Voice VLAN
encapsulation dot1Q 35
ip address 172.35.140.1 255.255.255.0
interface FastEthernet0/1
no ip address
shutdown
duplex auto
speed auto
ip forward-protocol nd
ip http server
ip http authentication local
ip http secure-server
ip http timeout-policy idle 600 life 86400 requests 10000
tftp-server flash:P00308010200.bin
tftp-server flash:P00308010200.sbn
tftp-server flash:P00308010200.sb2
tftp-server flash:P00308010200.loads
tftp-server flash:SCCP42.9-3-1SR3-1S.loads
tftp-server flash:apps42.9-3-1ES19.sbn
tftp-server flash:cnu42.9-3-1ES19.sbn
tftp-server flash:cvm42sccp.9-3-1ES19.sbn
tftp-server flash:dsp42.9-3-1ES19.sbn
tftp-server flash:jar42sccp.9-3-1ES19.sbn
tftp-server flash:term42.default.loads
tftp-server flash:term62.default.loads
tftp-server flash:SCCP45.9-3-1SR3-1S.loads
tftp-server flash:apps45.9-3-1ES19.sbn
tftp-server flash:cnu45.9-3-1ES19.sbn
tftp-server flash:cvm45sccp.9-3-1ES19.sbn
tftp-server flash:dsp45.9-3-1ES19.sbn
tftp-server flash:jar45sccp.9-3-1ES19.sbn
tftp-server flash:term45.default.loads
tftp-server flash:term65.default.loads
tftp-server flash:/Ringtones/Ringlist.xml alias Ringlist.xml
tftp-server flash:/Ringtones/DistinctiveRingList.xml alias DistinctiveRingList.x
ml
tftp-server flash:sip9971.9-4-1-9.loads
tftp-server flash:kern9971.9-4-1-9.sebn
tftp-server flash:rootfs9971.9-4-1-9.sebn
tftp-server flash:dkern9971.100609R2-9-4-1-9.sebn
tftp-server flash:sboot9971.031610R1-9-4-1-9.sebn
tftp-server flash:skern9971.022809R2-9-4-1-9.sebn
tftp-server flash:/g4-tones.xml alias United_States/g4-tones.xml
tftp-server flash:/gd-sip.jar alias English_United_States/gd-sip.jar
control-plane
mgcp profile default
telephony-service
max-ephones 24
max-dn 48
ip source-address 172.25.140.1 port 2000
cnf-file location flash:
load 7960-7940 P00308010200
load 7942 SCCP42.9-3-1SR3-1S.loads
load 7945 SCCP45.9-3-1SR3-1S.loads
load 7962 SCCP42.9-3-1SR3-1S.loads
load 7965 SCCP45.9-3-1SR3-1S.loads
max-conferences 8 gain -6
dn-webedit
transfer-system full-consult
create cnf-files version-stamp 7960 Feb 11 2014 07:18:32
ephone-dn 1
number 1001
description Phone 1
name Phone 1
hold-alert 30 originator
ephone-dn 2
number 1002
description Phone 2
name Phone 2
hold-alert 30 originator
ephone-dn 3
number 1003
description Phone 3
name Phone 3
hold-alert 30 originator
ephone 1
device-security-mode none
mac-address 001C.58FB.6E0F
button 1:1
ephone 2
device-security-mode none
mac-address 0014.A981.7F8A
button 1:2
ephone 3
device-security-mode none
mac-address 0006.5356.A4B8
button 1:3
alias exec con conf t
alias exec sib show ip int brief
alias exec srb show run | b
alias exec sri show run int
line con 0
exec-timeout 0 0
logging synchronous
line aux 0
line vty 0 4
privilege level 15
login local
transport input telnet ssh
transport output telnet ssh
line vty 5 15
privilege level 15
login local
transport input telnet ssh
transport output telnet ssh
scheduler allocate 20000 1000
ntp master 1
end
C2811#
Similar Messages
-
Cisco SIP Phone 9971 won't register on CME 8.6
Hello,
I'm facing a very strange problem:
a Cisco SIP Phone 9971 won't register on CME 8.6 running on a 2811
I have read all the related-postings to this and other Forum, but I have not been able to solve it.
One of the "potential solutions" was to make sure that the Phone had a Line configured.
But I think that the commands voice register dn and voice register pool are properly configured (see config below)
So frankly, I have no idea what I could be missing.
I'm pasting the Router's config.
I hope somebody is able to point me in the right direction.
Here is the config. Thank you!
C2811#sh run
Building configuration...
version 15.1
service timestamps debug datetime msec
service timestamps log datetime msec
no service password-encryption
hostname C2811
no aaa new-model
dot11 syslog
ip source-route
ip cef
ip dhcp excluded-address 172.25.140.1 172.25.140.10
ip dhcp excluded-address 172.35.140.1 172.35.140.10
ip dhcp pool Data
network 172.25.140.0 255.255.255.0
default-router 172.25.140.1
option 150 ip 172.25.140.1
dns-server 172.25.140.1
ip dhcp pool Voice
network 172.35.140.0 255.255.255.0
default-router 172.35.140.1
option 150 ip 172.35.140.1
dns-server 172.35.140.1
no ip domain lookup
no ipv6 cef
multilink bundle-name authenticated
voice service voip
allow-connections sip to sip
sip
registrar server expires max 3600 min 120
voice register global
mode cme
source-address 172.25.140.1 port 5060
max-dn 40
max-pool 42
load 9971 sip9971.9-4-1-9.loads
authenticate register
authenticate realm cisco
tftp-path flash:
create profile sync 0004820400584603
voice register dn 1
number 1010
allow watch
name Phone10
label Phone10
mwi
voice register pool 1
id mac 189C.5DB6.BD09
type 9971
number 1 dn 1
presence call-list
dtmf-relay rtp-nte
username adm password adm
call-forward b2bua busy 68600
codec g711ulaw
no vad
camera
video
voice-card 0
crypto pki token default removal timeout 0
crypto pki trustpoint TP-self-signed-1879153754
enrollment selfsigned
subject-name cn=IOS-Self-Signed-Certificate-1879153754
revocation-check none
rsakeypair TP-self-signed-1879153754
crypto pki certificate chain TP-self-signed-1879153754
certificate self-signed 01
(details ommited)
license udi pid CISCO2811 sn FTX1146A44H
username admin privilege 15 password 0 admin
redundancy
interface FastEthernet0/0
no ip address
duplex auto
speed auto
interface FastEthernet0/0.25
description Data VLAN
encapsulation dot1Q 25
ip address 172.25.140.1 255.255.255.0
interface FastEthernet0/0.35
description Voice VLAN
encapsulation dot1Q 35
ip address 172.35.140.1 255.255.255.0
interface FastEthernet0/1
no ip address
shutdown
duplex auto
speed auto
ip forward-protocol nd
ip http server
ip http authentication local
ip http secure-server
ip http timeout-policy idle 600 life 86400 requests 10000
tftp-server flash:P00308010200.bin
tftp-server flash:P00308010200.sbn
tftp-server flash:P00308010200.sb2
tftp-server flash:P00308010200.loads
tftp-server flash:SCCP42.9-3-1SR3-1S.loads
tftp-server flash:apps42.9-3-1ES19.sbn
tftp-server flash:cnu42.9-3-1ES19.sbn
tftp-server flash:cvm42sccp.9-3-1ES19.sbn
tftp-server flash:dsp42.9-3-1ES19.sbn
tftp-server flash:jar42sccp.9-3-1ES19.sbn
tftp-server flash:term42.default.loads
tftp-server flash:term62.default.loads
tftp-server flash:SCCP45.9-3-1SR3-1S.loads
tftp-server flash:apps45.9-3-1ES19.sbn
tftp-server flash:cnu45.9-3-1ES19.sbn
tftp-server flash:cvm45sccp.9-3-1ES19.sbn
tftp-server flash:dsp45.9-3-1ES19.sbn
tftp-server flash:jar45sccp.9-3-1ES19.sbn
tftp-server flash:term45.default.loads
tftp-server flash:term65.default.loads
tftp-server flash:/Ringtones/Ringlist.xml alias Ringlist.xml
tftp-server flash:/Ringtones/DistinctiveRingList.xml alias DistinctiveRingList.x
ml
tftp-server flash:sip9971.9-4-1-9.loads
tftp-server flash:kern9971.9-4-1-9.sebn
tftp-server flash:rootfs9971.9-4-1-9.sebn
tftp-server flash:dkern9971.100609R2-9-4-1-9.sebn
tftp-server flash:sboot9971.031610R1-9-4-1-9.sebn
tftp-server flash:skern9971.022809R2-9-4-1-9.sebn
tftp-server flash:/g4-tones.xml alias United_States/g4-tones.xml
tftp-server flash:/gd-sip.jar alias English_United_States/gd-sip.jar
control-plane
mgcp profile default
telephony-service
max-ephones 24
max-dn 48
ip source-address 172.25.140.1 port 2000
cnf-file location flash:
load 7960-7940 P00308010200
load 7942 SCCP42.9-3-1SR3-1S.loads
load 7945 SCCP45.9-3-1SR3-1S.loads
load 7962 SCCP42.9-3-1SR3-1S.loads
load 7965 SCCP45.9-3-1SR3-1S.loads
max-conferences 8 gain -6
dn-webedit
transfer-system full-consult
create cnf-files version-stamp 7960 Feb 11 2014 07:18:32
ephone-dn 1
number 1001
description Phone 1
name Phone 1
hold-alert 30 originator
ephone-dn 2
number 1002
description Phone 2
name Phone 2
hold-alert 30 originator
ephone-dn 3
number 1003
description Phone 3
name Phone 3
hold-alert 30 originator
ephone 1
device-security-mode none
mac-address 001C.58FB.6E0F
button 1:1
ephone 2
device-security-mode none
mac-address 0014.A981.7F8A
button 1:2
ephone 3
device-security-mode none
mac-address 0006.5356.A4B8
button 1:3
alias exec con conf t
alias exec sib show ip int brief
alias exec srb show run | b
alias exec sri show run int
line con 0
exec-timeout 0 0
logging synchronous
line aux 0
line vty 0 4
privilege level 15
login local
transport input telnet ssh
transport output telnet ssh
line vty 5 15
privilege level 15
login local
transport input telnet ssh
transport output telnet ssh
scheduler allocate 20000 1000
ntp master 1
end
C2811#Thank you for your reply.
I did some debugs and the results are very strange!
This is what I got:
Feb 24 18:01:12.219: //-1/xxxxxxxxxxxx/SIP/Msg/ccsipDisplayMsg:
Sent:
SIP/2.0 400 Bad Request
Via: SIP/2.0/UDP 172.35.140.12:5060;branch=z9hG4bK08011844
From: ;tag=189c5db6bd09000260cf3daf-289a76d1
To: ;tag=52488-160A
Date: Mon, 24 Feb 2014 18:01:12 GMT
Call-ID: [email protected]
CSeq: 1000 REFER
Content-Length: 0
Contact:
Feb 24 18:01:12.291: //-1/xxxxxxxxxxxx/SIP/Msg/ccsipDisplayMsg:
Received:
REGISTER sip:172.25.140.1 SIP/2.0
Via: SIP/2.0/UDP 172.35.140.12:5060;branch=z9hG4bK1e9ad079
From: ;tag=189c5db6bd0900032df02e9c-25d79707
To:
Call-ID: [email protected]
Max-Forwards: 70
Date: Fri, 01 Jan 1982 00:02:41 GMT
CSeq: 101 REGISTER
User-Agent: Cisco-CP9971/9.4.1
Contact: ;+sip.instance="
000000-0000-0000-0000-189c5db6bd09>";+u.sip!devicename.ccm.cisco.com="SEP189C5DB
6BD09";+u.sip!model.ccm.cisco.com="493";video
Supported: replaces,join,sdp-anat,norefersub,resource-priority,extended-refer,X-
cisco-callinfo,X-cisco-serviceuri,X-cisco-escapecodes,X-cisco-service-control,X-
cisco-srtp-fallback,X-cisco-monrec,X-cisco-config,X-cisco-sis-6.0.2,X-cisco-xsi-
8.0.1
Content-Length: 0
Reason: SIP;cause=200;text="cisco-alarm:22 Name=SEP189C5DB6BD09 ActiveLoad=sip99
71.9-4-1-9.loads InactiveLoad=sip9971.9-3-2SR1-1.loads Last=reset-reset"
Expires: 3600
Feb 24 18:01:12.395: voice_reg_get_reg_expires_timer: no voice register pool found
Feb 24 18:01:12.395: VOICE_REG_POOL: Register request for (1010) from (172.35.140.12)
Feb 24 18:01:12.395: VOICE_REG_POOL: Contact matches pool 1 number list 1
Feb 24 18:01:12.395: VOICE_REG_POOL: No entry for (172.35.140.12) found in srst contact table
Feb 24 18:01:12.395: VOICE_REG_POOL: key(1010) contact(172.35.140.12:5060) add to contact table
Feb 24 18:01:12.395: VOICE_REG_POOL: No entry for (1010) found in contact table
Feb 24 18:01:12.399: VOICE_REG_POOL: key(1010) contact(172.35.140.12) added to contact table
Feb 24 18:01:12.399: VOICE_REG_POOL: key(172.35.140.12) contact(1010) add to srst contact table
Feb 24 18:01:12.399: VOICE_REG_POOL: No entry for (172.35.140.12) found in srst contact table
Feb 24 18:01:12.399: VOICE_REG_POOL: key(172.35.140.12) contact(1010) added to srst contact table
Feb 24 18:01:12.399: VOICE_REG_POOL pool->tag(1), dn->tag(1), submask(1)
But right after these errors, I get the following:
Feb 24 18:01:12.399: VOICE_REG_POOL: Creating param container for dial-peer 4000
1.VOICE_REG_POOL pool->tag(1), dn->tag(1), submask(1)
VOICE_REG_POOL pool_tag(1), dn_tag(1)
Feb 24 18:01:12.399: VOICE_REG_POOL: Created dial-peer entry of type 0
Feb 24 18:01:12.399: VOICE_REG_POOL: Registration successful for 1010, registration id is 1
Feb 24 18:01:12.411: VOICE_REG_POOL: Contact matches pool 1 number list 1
Feb 24 18:01:12.411: VOICE_REG_POOL: GW SIS: X-cisco-cme-sis-1.0.0
Feb 24 18:01:12.411: VOICE REGISTER POOL-1 has registered.
Name:SEP189C5DB6BD09 IP:172.35.140.12 DeviceType:Phone
Feb 24 18:01:12.411: VOICE_REG_POOL: Pool[1]: service-control (reset type: 2) message sent to sip:[email protected]
Feb 24 18:01:12.411: voice_reg_privacy_update_to_phone: delay sending privacy update during bulk registration
Feb 24 18:01:12.415: //1/7B0070C28003/SIP/Msg/ccsipDisplayMsg:
====================
And when I do a sh voice register pool, I get the following:
C2811#sh voice register pool 1
Pool Tag 1
Config:
Mac address is 189C.5DB6.BD09
Type is 9971
Number list 1 : DN 1
Proxy Ip address is 0.0.0.0
Current Phone load version is Cisco-CP9971/9.4.1
DTMF Relay is enabled, rtp-nte
Call Waiting is enabled
DnD is disabled
Video is enabled
Camera is enabled
Busy trigger per button value is 0
call-forward b2bua busy 68600
keep-conference is enabled
registration expires timer max is 3600 and min is 120
username adm password adm
kpml signal is enabled
Lpcor Type is none
blf call list is enabled
Transport type is udp
service-control mechanism is supported
registration Call ID is [email protected]
Registration method: per line
Privacy feature is not configured.
Privacy button is disabled
active primary line is: 1010
contact IP address: 172.35.140.12 port 5060
Phone SIS Version: 6.0.2
GW SIS Version: 1.0.0
Dialpeers created:
Dial-peers for Pool 1:
dial-peer voice 40001 voip
destination-pattern 1010
session target ipv4:172.35.140.12:5060
session protocol sipv2
dtmf-relay rtp-nte
digit collect kpml
codec g711ulaw bytes 160
no vad
call-fwd-busy 68600
after-hours-exempt FALSE
Statistics:
Active registrations : 4
Total SIP phones registered: 1
Total Registration Statistics
Registration requests : 4
Registration success : 4
Registration failed : 0
unRegister requests : 0
unRegister success : 0
unRegister failed : 0
Attempts to register
after last unregister : 0
Last register request time : 18:11:43.551 UTC Mon Feb 24 2014
Last unregister request time :
Register success time : 18:11:43.551 UTC Mon Feb 24 2014
Unregister success time :
C2811#
So apparently the Phone is actually registered!
However, the Phone screens still shows this message: Phone Not Registered.
So frankly I don't understand what's going on!
I really hope somebody can help. Thanks! -
Cisco SIP Phone 9971 will not register on CME 8.6
Hello,
I'm trying to configure a Cisco SIP Phone 9971,
but it won't register on CME 8.6, which is running on a 2811
The Phone shows this error message: Phone Not Registered.
And when I check the the Status Messages in the Phone, I see the following:
VPN Error: vpn is not configured
Actually, it shows all these 4 messages in a constant Loop:
12:01:59a SEP189C5DB6BD09.cnf.xml (TFTP)
12:01:59a No Trust List instaled
12:01:59a Updating Trust list
12:02:00a VPN Error: VPN is not Configured
It seems that this VPN Error is keeping the Phone from registering.
This is repeated for ever and the Phone never registers; at least that's what it appears.
However, when I do a sh voice register pool, I get the following:
C2811#sh voice register pool 1
Pool Tag 1
Config:
Mac address is 189C.5DB6.BD09
Type is 9971
Number list 1 : DN 1
Proxy Ip address is 0.0.0.0
Current Phone load version is Cisco-CP9971/9.4.1
DTMF Relay is enabled, rtp-nte
Call Waiting is enabled
DnD is disabled
Video is enabled
Camera is enabled
Busy trigger per button value is 0
call-forward b2bua busy 68600
keep-conference is enabled
registration expires timer max is 3600 and min is 120
username adm password adm
kpml signal is enabled
Lpcor Type is none
blf call list is enabled
Transport type is udp
service-control mechanism is supported
registration Call ID is [email protected]
Registration method: per line
Privacy feature is not configured.
Privacy button is disabled
active primary line is: 1010
contact IP address: 172.35.140.12 port 5060
Phone SIS Version: 6.0.2
GW SIS Version: 1.0.0
Dialpeers created:
Dial-peers for Pool 1:
dial-peer voice 40001 voip
destination-pattern 1010
session target ipv4:172.35.140.12:5060
session protocol sipv2
dtmf-relay rtp-nte
digit collect kpml
codec g711ulaw bytes 160
no vad
call-fwd-busy 68600
after-hours-exempt FALSE
Statistics:
Active registrations : 4
Total SIP phones registered: 1
Total Registration Statistics
Registration requests : 4
Registration success : 4
Registration failed : 0
unRegister requests : 0
unRegister success : 0
unRegister failed : 0
Attempts to register
after last unregister : 0
Last register request time : 18:11:43.551 UTC Mon Feb 24 2014
Last unregister request time :
Register success time : 18:11:43.551 UTC Mon Feb 24 2014
Unregister success time :
C2811#
This sh voice register pool seems to indicate that the Phone has actually registered.
But I still get the Phone Not Registered message on the screen!
I did some Debugs and they also seem to indicate that the Phone has indeed registered:
Feb 24 18:01:12.399: VOICE_REG_POOL: Creating param container for dial-peer 4000
1.VOICE_REG_POOL pool->tag(1), dn->tag(1), submask(1)
VOICE_REG_POOL pool_tag(1), dn_tag(1)
Feb 24 18:01:12.399: VOICE_REG_POOL: Created dial-peer entry of type 0
Feb 24 18:01:12.399: VOICE_REG_POOL: Registration successful for 1010, registration id is 1
Feb 24 18:01:12.411: VOICE_REG_POOL: Contact matches pool 1 number list 1
Feb 24 18:01:12.411: VOICE_REG_POOL: GW SIS: X-cisco-cme-sis-1.0.0
Feb 24 18:01:12.411: VOICE REGISTER POOL-1 has registered.
Name:SEP189C5DB6BD09 IP:172.35.140.12 DeviceType:Phone
So frankly, I have no idea why the Phone keeps showing the Phone Not Registered message.
I'm pasting the Router's config.
I hope somebody is able to point me in the right direction.
Here is the config. Thank you!
C2811#sh run
Building configuration...
version 15.1
service timestamps debug datetime msec
service timestamps log datetime msec
no service password-encryption
hostname C2811
no aaa new-model
dot11 syslog
ip source-route
ip cef
ip dhcp excluded-address 172.25.140.1 172.25.140.10
ip dhcp excluded-address 172.35.140.1 172.35.140.10
ip dhcp pool Data
network 172.25.140.0 255.255.255.0
default-router 172.25.140.1
option 150 ip 172.25.140.1
dns-server 172.25.140.1
ip dhcp pool Voice
network 172.35.140.0 255.255.255.0
default-router 172.35.140.1
option 150 ip 172.35.140.1
dns-server 172.35.140.1
no ip domain lookup
no ipv6 cef
multilink bundle-name authenticated
voice service voip
allow-connections sip to sip
sip
registrar server expires max 3600 min 120
voice register global
mode cme
source-address 172.25.140.1 port 5060
max-dn 40
max-pool 42
load 9971 sip9971.9-4-1-9.loads
authenticate register
authenticate realm cisco
tftp-path flash:
create profile sync 0004820400584603
voice register dn 1
number 1010
allow watch
name Phone10
label Phone10
mwi
voice register pool 1
id mac 189C.5DB6.BD09
type 9971
number 1 dn 1
presence call-list
dtmf-relay rtp-nte
username adm password adm
call-forward b2bua busy 68600
codec g711ulaw
no vad
camera
video
voice-card 0
crypto pki token default removal timeout 0
crypto pki trustpoint TP-self-signed-1879153754
enrollment selfsigned
subject-name cn=IOS-Self-Signed-Certificate-1879153754
revocation-check none
rsakeypair TP-self-signed-1879153754
crypto pki certificate chain TP-self-signed-1879153754
certificate self-signed 01
(details ommited)
license udi pid CISCO2811 sn FTX1146A44H
username admin privilege 15 password 0 admin
redundancy
interface FastEthernet0/0
no ip address
duplex auto
speed auto
interface FastEthernet0/0.25
description Data VLAN
encapsulation dot1Q 25
ip address 172.25.140.1 255.255.255.0
interface FastEthernet0/0.35
description Voice VLAN
encapsulation dot1Q 35
ip address 172.35.140.1 255.255.255.0
interface FastEthernet0/1
no ip address
shutdown
duplex auto
speed auto
ip forward-protocol nd
ip http server
ip http authentication local
ip http secure-server
ip http timeout-policy idle 600 life 86400 requests 10000
tftp-server flash:P00308010200.bin
tftp-server flash:P00308010200.sbn
tftp-server flash:P00308010200.sb2
tftp-server flash:P00308010200.loads
tftp-server flash:SCCP42.9-3-1SR3-1S.loads
tftp-server flash:apps42.9-3-1ES19.sbn
tftp-server flash:cnu42.9-3-1ES19.sbn
tftp-server flash:cvm42sccp.9-3-1ES19.sbn
tftp-server flash:dsp42.9-3-1ES19.sbn
tftp-server flash:jar42sccp.9-3-1ES19.sbn
tftp-server flash:term42.default.loads
tftp-server flash:term62.default.loads
tftp-server flash:SCCP45.9-3-1SR3-1S.loads
tftp-server flash:apps45.9-3-1ES19.sbn
tftp-server flash:cnu45.9-3-1ES19.sbn
tftp-server flash:cvm45sccp.9-3-1ES19.sbn
tftp-server flash:dsp45.9-3-1ES19.sbn
tftp-server flash:jar45sccp.9-3-1ES19.sbn
tftp-server flash:term45.default.loads
tftp-server flash:term65.default.loads
tftp-server flash:/Ringtones/Ringlist.xml alias Ringlist.xml
tftp-server flash:/Ringtones/DistinctiveRingList.xml alias DistinctiveRingList.x
ml
tftp-server flash:sip9971.9-4-1-9.loads
tftp-server flash:kern9971.9-4-1-9.sebn
tftp-server flash:rootfs9971.9-4-1-9.sebn
tftp-server flash:dkern9971.100609R2-9-4-1-9.sebn
tftp-server flash:sboot9971.031610R1-9-4-1-9.sebn
tftp-server flash:skern9971.022809R2-9-4-1-9.sebn
tftp-server flash:/g4-tones.xml alias United_States/g4-tones.xml
tftp-server flash:/gd-sip.jar alias English_United_States/gd-sip.jar
control-plane
mgcp profile default
telephony-service
max-ephones 24
max-dn 48
ip source-address 172.25.140.1 port 2000
cnf-file location flash:
load 7960-7940 P00308010200
load 7942 SCCP42.9-3-1SR3-1S.loads
load 7945 SCCP45.9-3-1SR3-1S.loads
load 7962 SCCP42.9-3-1SR3-1S.loads
load 7965 SCCP45.9-3-1SR3-1S.loads
max-conferences 8 gain -6
dn-webedit
transfer-system full-consult
create cnf-files version-stamp 7960 Feb 11 2014 07:18:32
ephone-dn 1
number 1001
description Phone 1
name Phone 1
hold-alert 30 originator
ephone-dn 2
number 1002
description Phone 2
name Phone 2
hold-alert 30 originator
ephone-dn 3
number 1003
description Phone 3
name Phone 3
hold-alert 30 originator
ephone 1
device-security-mode none
mac-address 001C.58FB.6E0F
button 1:1
ephone 2
device-security-mode none
mac-address 0014.A981.7F8A
button 1:2
ephone 3
device-security-mode none
mac-address 0006.5356.A4B8
button 1:3
alias exec con conf t
alias exec sib show ip int brief
alias exec srb show run | b
alias exec sri show run int
line con 0
exec-timeout 0 0
logging synchronous
line aux 0
line vty 0 4
privilege level 15
login local
transport input telnet ssh
transport output telnet ssh
line vty 5 15
privilege level 15
login local
transport input telnet ssh
transport output telnet ssh
scheduler allocate 20000 1000
ntp master 1
end
C2811#VPN is not Configured prints on all phones now with the built-in VPN client if VPN isn't configured. That's normal and is just cosmetic. That should not be causing your registration issues.
-
Cisco ip phone 9971 registration failed with CME 8.6 on WAN
Dear Sir
Subject: Cisco ip
phone 9971 registration failed
with CME 8.6 on WAN
I have a WAN simulation with one Cisco2811 router one Cisco1841 router (connected with fast Ethernet interface) plus one layer 2 switch.
I upgraded the 2811 IOS to 15.4M and installed CME8.6, when we tried to add 9971 sip phone If the traffic goes throw LAN (Same subnet- directly from switch to 2811) everything is fine and the SIP phone (9971) added with no problem but when I change the subnet and traffic goes throw WAN
( from 1841 routed to 2811 with default route) my phone didn't register.
It will be great if anybody could help!!
If you can solve my problem, I will be happy to compensate.Try binding SIP to an interface on which Phone can reach (Use "voice service voip" "sip" and then bind)
Udit -
Forced Authorization Code For Cisco SIP Phone 3905
Hi Team,
Can i configure Cisco SIP Phone 3905 to use Forced Authorization Code ? I am using Call Manager 9.X.
Regards,
Praful SartapeHi Praful,
Yes you right for CME but for CUCM some sip phones supports FAC , as far as 3905 is concerned it supports FAC .
http://www.cisco.com/en/US/docs/voice_ip_comm/cuipph/3905/8_6/english/admin_guide/IP05_BK_CDEEDD7F_00_admin-guide-3905_chapter_0101.html#IP05_RF_A5029279_00
I didnt find link for CUCM 9.x but that above link will help.
And also check this thread- https://supportforums.cisco.com/thread/2125452
Rate all the helpful post.
Thanks
Manish -
I have CUCM (9.1.2) and Sip phone 9971.
When user hangup phone, and try to dial phone number to PSTN, he waiting about 15 seconds before sip phone make a call. I would to make this time about 1 or 2 seconds. If he call to Polycom server, he does not waiting any time.
I changed any timer - no effects.
I apply "Sip dial rules" nothing changed.
Can anybody tell me how i can fix it?Is only one user impacted. Normally delays in the dialing are due to below:
1) Overlap in dial plan or
2) Interdigit timeout T302 (default is 15 sec) that comes into play specially if you are hitting a variable route pattern
So either you can check your dial plan and have specific route patterns or you can change the inter digit time out to something less 5 secs maybe according to your issue. (3 secs is the minimum value you can configure)
To change inter digit timeout T302 go to - Service Parameters, Call Manager service and search T302. Change it to the required value (its in msecs)
-Terry
Please rate all helpful posts -
hi. my iphone 3gs was stuck on apple logo, does not charging. when i replace the battery, it works, my promblem not is, in can't or won't read the simcard. i cant activate my phone. even i put att simcard. how can i activate it? please help me. thanks.
Apple recommends backing up the data when you're getting the battery replaced by them. So I assume that you will likely lose the data during this process.
Will the data on my iPhone be preserved?
No, during the service process all data on your iPhone will be erased. Before obtaining service, it is important to back up your data using iCloud or iTunes. Apple is not responsible for the loss of information while servicing your iPhone and does not offer any data transfer service. During service, Apple may exchange your iPhone with an iPhone that is new or equivalent to new in performance and reliability.
Following service, your iPhone may have a newer operating system (iOS) version and you will need torestore your data using the method used to back it up (iCloud or iTunes). As a result, you may also need to update your App Store applications to ensure compatibility with the newer iOS. If you experience a problem with an application purchased from the App Store, check to see if an update is available or contact the application vendor directly.
copied from Apple - Support - Service Answer Center -
I am facing issue in Receiving incoming calls, Name not getting displayed though the same has been saved in my phone book!! I have done sync from Windows contacts.. please help if some1 knows how to rectify the issue...
Has your carrier been having issues with Call Display? Do the telephone numbers come up when people call, or does it just show 'Unknown Number' or 'Blocked' ?
-
I have updated my 4S i phone with ios 8.1.2, while activating my iphone, i forgot my password. I am able to sign in my apple id in pc (manage my account) but not not able to sign in my i phone and message- your apple id has been disable for security reasons please help.
my apple id is with extension @ gmail.com but for activation it is mentioned that it is linked with extension of @me.comHi ulhas1frombanihal,
Welcome to the Support Communities! Because your account has been disabled, you will need to contact Apple ID account security to straighten this out.
Contact Apple for help with Apple ID account security - Apple Support
http://support.apple.com/en-us/HT5699
I hope this information helps ....
- Judy -
Help - i recently made put together a high quality movie for a relative, it has taken me months to complete and it goes for a total of 9 hours and 43 minutes ,however, it won't let me export the video at all! please help - its taken ages to make it!
9 hours??!
Twice the length of a cinema epic?
How are you expecting to distribute it?
iDVD encoding settings:
http://docs.info.apple.com/article.html?path=iDVD/7.0/en/11417.html
Short version:
Best Performance is for videos of up to 60 minutes
Best Quality is for videos of up to 120 minutes
Professional Quality is also for up to 120 minutes but even higher quality (and takes much longer)
That was for single-layer DVDs. Double these numbers for dual-layer DVDs.
Professional Quality: The Professional Quality option uses advanced technology to encode your video, resulting in the best quality of video possible on your burned DVD. You can select this option regardless of your project’s duration (up to 2 hours of video for a single-layer disc and 4 hours for a double-layer disc). Because Professional Quality encoding is time-consuming (requiring about twice as much time to encode a project as the High Quality option, for example) choose it only if you are not concerned abo
In both cases the maximum length includes titles, transitions and effects etc. Allow about 15 minutes for these.
You can use the amount of video in your project as a rough determination of which method to choose. If your project has an hour or less of video (for a single-layer disc), choose Best Performance. If it has between 1 and 2 hours of video (for a single-layer disc), choose High Quality. If you want the best possible encoding quality for projects that are up to 2 hours (for a single-layer disc), choose Professional Quality. This option takes about twice as long as the High Quality option, so select it only if time is not an issue for you.
Use the Capacity meter in the Project Info window (choose Project > Project Info) to determine how many minutes of video your project contains.
NOTE: With the Best Performance setting, you can turn background encoding off by choosing Advanced > “Encode in Background.” The checkmark is removed to show it’s no longer selected. Turning off background encoding can help performance if your system seems sluggish.
And whilst checking these settings in iDVD Preferences, make sure that the settings for NTSC/PAL and DV/DV Widescreen are also what you want.
http://support.apple.com/kb/HT1502?viewlocale=en_US -
igrabber won't recognise the igrabber under 'digitisers'....please help....searched the web for a lot of people with the same problem but no one seems to have an answer!!!!
i have the same problem. under digitisers its only isight cam and in video settings under source igrabber is greyed out ! did you get anyupdate on this problem ?
-
I'm trying to update my iPhone 4s to iOS 7.1.2 and it just froze on the screen with the apple and the loading bar, it won't move and it's been like 45 minutes PLEASE HELP!
iOS updates can take a while, try back in an hour or so. My iPad took half an hour for an incremental update. And that was on a fast home WiFi.
-
I would like to know how i stop some albums ive bought from transfering to my iphone i delete them from itunes but when i sync my phone they transfer from my iphone this is a pain some one please help!!
Burb79 wrote:
I thought of that one two tried it but still no joy. I have an ipad2 as well which I set up to not sync any music to it but for some reason the albums have got onto that as well. im thinkin its somthing to do with the dam cloud thing
Go to Settings/ Store and under the category "Automatic Downloads" you can turn OFF the automatic download of purchases to your device (this needs to be done for each device). There's also a setting in iTunes just for automatic pushes to your iTunes library.
To remove a purchase you've made directly to your device, you can either:
a- Swipe across the song title from left to right and press Delete, or
b- If you auto-sync your device, connect to iTunes and click on the Music tab where you define your sync settings (the Music tab is to the right of the overall Summary page of your device). At the bottom of the Music tab you'll see direct purchases that are on your device -- simply un-check those and click "Apply" or "Sync" to remove them.
c- If you manually manage music on your device, connect to iTunes and click the small arrow to the left of your device name, and then click on the Music folder under your device. Then navigate to the item(s) you want to remove and then delete them.
To prevent things from syncing from your library to your device, there are many ways to do that (un-checking things in your library is one way, but not the best IMO). Might want to read the manual or some online tutorials on iTunes if you want to learn more. -
i have no messages in my phone but my storage is 90% full and in my usage it says i have 12MG in messages (saved) but i dont have any messages in my phone - where are they saved ? how can i delete them? please help
pamalushka54,
We want to make sure that we get your phone up and running. Can you look to see where you have the most stuff stored at. Settings>General>Usage>Storage.
This will tell you what exactly is using everything. Then you can delete things from there.
RobinD_VZWSupport
Follow us on twitter @VZWSupport -
My phone got stolen is there anyway to track it without icloud?please help me
My phone got stolen is there anyway to track it without icloud?please help me
Sorry khuber,
There is no way to "track" your phone without using Find My iPhone, which has to be set up in iCloud in order to work....
You can report it to the police.
Sorry
GB
Maybe you are looking for
-
About pop up in standard transaction
hello everyone, I need help in one standard transaction.In migo transaction after inserting excise invoice i am getting error " Excise invocie XXXX for the vendor xxxxx exits. It means systme is checking if a same excise invoice no is entered for sam
-
How to do the validation in sap xi (input file)
hi, how to do the validation in sap xi (input file)? regards Ruban
-
Central Person and Contact person relationship
Hello Friends, I have HR replicated org.struct.where central user creation was active I maintained Table T77SO for local user creation HRALX PBPHR CREATE HRALX PBPON ON HRALX HRAC X Now i am able to integrate user thru users_gen in org.stru
-
Undo file Having huge read average time more than 20ms
Please, I'm working on oracle 10g, windows server 2003. From the file I/O stats, I found that the Average read I/O from the undo files is more than 20ms, this contrast with other files where the same I/O metric is less then 0.5ms. Can someone give me
-
Problem when we dowload spool list into excel.
Hello Gurus, I have developed an custom report, The output contains 15 columns. When i run the report in foreground the output will be displayed in correct format also when i download the report list into excel(List->Save/Send->File) then the records