Cisco Works "Devices not configured in ACS"
Hi!
I have instaled Cisco Works ver. 4.3.1
I have added using the Device Discovery, my devices. Some of them where not configured already on ACS with the loopback address, that was the one on the discovery configurations. Because of that, i could not manage those devices, althoug i could authenticate on them. I then updated the ACS with the loopback address, and configured the router's to authenticate using the source-interface of the loopback.
The problem is that i keep not being able to manage this devices on the cworks, because the are still as "Devices not configured in ACS".
Can anyone help me here?
Regard's
Miguel Amaral
Hi,
This happens, when you integrate the ciscoworks with ACS and Router/switches not configured with ACS. Try to reconfigure the device in ACS, try removing and adding it again in common services...Try for a single device and check it out... Try stopping/starting cw services after that // net stop crmdmgtd, net start crmdmgtd. Revert with the results..
Similar Messages
-
Ciscoworks - devices "not configured in ACS"
Hi all,
Can anyone explain why Ciscoworks places some new devices in the above category even when the device config, ACS, etc is all configured correctly? I have a handful of devices that keep going into this category and there is nothing I can do to stop it happening - it is a real hassle as you have to then set CW to non ACS mode restart the daemon, delete the entries etc etc.
If anyone can describe how I can get CW to manage such devices properly and possibly even tell me how to stop it happening in the future it would be of great help.
Many thanks in advance (though I know some of you would rather have points ;-)
ScottHi Scott ,
Device will fall to " Devices not Configured in ACS " only in 2 condition :
1. Device is actually does not Exist in ACS
2. It EXist in ACS with different IPADDRESS or HOST NAME.
There is no direct way to delete these devices once they are on the Not Configured
in ACS list. However, one workaround is:
Step 1. Create a dummy NDG group in ACS to include these devices.
Step 2. Delete the devices in DCR and then in ACS.
Note: In order to delete a device from DCR we need to follow this procedure:
1.- Go to Common Services >> Devices and Credentials >> Reports >>
Devices that are not configured in ACS and generate a report.
2.- Now that we have all the devices that we want to delete, please go to
Common Services
>> Device and Credentials >> Device Management and select all the devices
from CS (Common Services database).
3.- Click on Delete and a confirmation message will pop, agree to this.
I hope this will help you
Thanks
Afroj -
I have some devices in my LMS 3.2 Master-Slave ACS-mode, that are, according to the DCR and AAA portlet, not configured in ACS
However I have checked that the devices are in ACS (in NDG and based on ip addresses, unique or by using wildcards)
What could be the reason why LMS can't find the devices in ACS?Hi,
If you have configured the devices in ACS and the LMS and ACS intergrity has been done then we need to break the integrity and redo it once again.
break the ACS and cisco works integrity, restart the deamons and then integrate it once again.
Please let me know if it helps.
Regards,
podhillo -
hi
ive recently downloaded firefox 2.0 and some openoffice onto my ibook, but when I try to launch the .dmg files i get a 'device not configured' error message. can anyone help? apologies if this is far too easy.
thanks in advance
johnNot sure about FireFox specifically, but .dmg files should open and expand/mount automatically when you double-click on them. Make sure FireFox completely downloaded the file, and use Get Info from the File menu to check permissions to make sure you have read/write access to the file. If that doesn't work, try launching Disk Utility to see if it will recognize and mount the file from there, or see if you can verify the CheckSum (basically make sure the file is not corrupt).
Other than that, I'm stumped. -
Open Error 6: Device not configured
I recently had my hard drive replaced and restored to factory settings. I then used a time machine backup and the Migration Assistant to get everything I had back to where it belonged.
Things worked for a day or so, but with a few crashes here and there. Yesterday, I tried to use iTunes and kept getting an error message about the database (-50, unable to mount database). The problem is that the whole system would freeze and I had to shut down and restart every time. Sometimes I could load the OS, sometimes not. This morning I ran Disk Utility to verify the disk (it passed) and the permissions. When I tried to repair permissions, I got hundreds of messages like this : "Open Error 6: Device not configured on" and then a list of paths, such as "System/Library/Perl/5.10.0/darwin-thread-multi-2level/auto/POSIX/getgrgld.al", and "System/Library/Frameworks/Ruby.framework/Versions/1.8/usr/share/ri/....." etc. Literally hundreds of those messages.
Does anyone know what this means? And how should I fix it?!?
Thanks!I'm going to suggest that you ask in the Snow Leopard forums here:
http://discussions.apple.com/category.jspa?categoryID=263
This is likely a system software error, and the SL gurus that hang out over there might have suggestions for you.
Good luck! -
Disk Utility Restoring Error - Device not Configured
Hi all,
A mate has given me a USB flash drive that doesn't work. I tried to create an backup image using Resuce Pro from SanDisk and it came up with a NDIF file. What I then did was partioned an external hard drive and restore using the image as source and the new partition as destination. 2 seconds later an error comes up saying restore error, could not validate source - device not configured. Am I the only one that has this problem or have I done anything wrong during the process?
Cheers,
KeefeNDIF is an obsolete format. You'd probably have to convert it to some kind of DMG first (Images > Convert.)
-
All DMG files "device not configured"??
Alright, this just did start happening. All the dmg files that i try to open, i get the same error. A warning box comes up, and it says, "The following disk images failed to mount" Then it lists the name of the device, example..."vlc-0.8.5.dmg"...and then shows a reason, which is, for all of them, "device not configured". I also get errors when trying to update to the newest os x as well. Anyone know what to do?
HELP!!!!!!!!! PLEASE!!!!!!!!!!!!!
I've mis-read your post, had similar issues to the person who wrote the original querie, copied these items;
/System/Library/Extension.kextcache
and
/System/Library/Caches/com.apple.kernalcaches/
to my desktop, removed them from their folders and restarted. Well, tried to restart.
The grey screen came up with the spinning gear and apple logo, then black text over laying that saying something about a stack error. I can't start my machine at all, not even from the OSx disk. It gets to Preparing Installation and keeps on spinning!
If any one can help I'd be eternally grateful. I can't believe this has happened!
Cheers
Kirstin -
Cisco Works does note recognise 7204VXR NPE-G2 variant IOS
I am trying to load a 7200 NPE-G2 variant IOS into our Cisco Works software repository in order to then upload it to a 7204VXR. When browsing to the folder containing the IOS and then attempting load, Ciso Works does not recognise the NPE-G2 variants (with file names starting c7200p), however it does recognise vanilla c7200 variants.
We are running with LMS 2.6, RME 4.0.5, DFM 2.0.6
Do we need to upgrade?You will need to update your RME device packages to the latest versions. Go to Common Services > Software Center > Device Update, and check the boxes next to RME and Common Services. Download and install all available packages, then you should be able to add the c7200p image to the repository.
-
Cisco Works LMS R3.1 with ACS R5.1
I search on internet about the AAA integration between LMS R3.1 y ACS R5.1, and all the information that I found it's related to ACS R4.1. It's possible to integrate with ACS R5.1.
Regards and thanks in advanced
Luis MartinezNael,
Sorry to batter you, but I was trying to migrate my Cisco Works LMS R3.1 to R3.2 and from the support page of CISCO I just can donwload the following version LMS R3.2.1 (LMS R3.2 service pack 1). I tried to install that version but i got an error that saids "LMS R3.2.1 needs LMS R3.2 installed on the server"
Could you please tell me where can I download the complete and initial LMS R3.2.
Thanks in advanced for your kindly help.
Luis Martinez -
Polycom utilising Cisco WAN device not seeing remote video but remote can see us
Hi,
Before I proceed, I can say this, system was working fine before untill all of a sudden it cannot.
I Was called in as an expert to assist our Branch Tech who claims no changes were done.
Now here is the case:
When I test calling Polycom test sites, my video displays to them but I can't see their video.
I have captured some log files m the Polycom PC but could not pick out the fault.
PC can ping the remote end and virtually everything goes through out to Internet.
We come off an ISP through their VPN wireless link.
We have a cisco 2800 series router.
I am not too keen at the Remote end as they can see us not we cannot see them.
In Our Router we only have Static NT of the internal IP for the polycom PC to the Single Public IP which remote users use to call us.
Any help would be much appreciated.Just got off the phone with SonicWall Support and here is the solution to the AirPlay issue:
Follow these directions:
http://www.fuzeqna.com/sonicwallkb/consumer/kbdetail.asp?kbid=9059&SearchType=ad vanced&referrer=&gpn=&CustID=&bUseEditor=&keyword=airplay&rfield=&sortmethod=re l &usertype=&gpv=&catID2=&formaction=search&catID1=&IncludeHTML=&logsearch=False& c atID3=&TotalResults=5491&sct=KB&submitbutton=Go&match=and
http://www.fuzeqna.com/sonicwallkb/consumer/kbdetail.asp?kbid=10132
If you want to only allow the AirPlay/Bonjour ports, use this list:
http://bowersandwilkins.custhelp.com/app/answers/detail/a_id/55/~/firewall-ports -utilised-by-airplay
Finally, enable Interface Trust on the Wireless Interface (Network > Zones).
AirPlay will work via wireless using these directions! -
GONE FROM DEVICE NOT CONFIGURED TO BROKEN MACHINE. PLEASE HELP!
HELP!!!!!!!!! PLEASE!!!!!!!!!!!!!
I read a post in response to a query from someone who I had similar issues to and copied these items;
/System/Library/Extension.kextcache
and
/System/Library/Caches/com.apple.kernalcaches/
to my desktop, removed them from their folders and restarted. Well, tried to restart.
The grey screen came up with the spinning gear and apple logo, then black text over laying that saying something about a stack error. I can't start my machine at all, not even from the OSx disk. It gets to Preparing Installation and keeps on spinning!
If any one can help I'd be eternally grateful. I can't believe this has happened!
Cheers
KirstinYou would have to boot in single-user mode, mount the filesystem and copy the files back into the extensions fiolder. I'm not going to type the whole procedure out here but some Googling will get you the exact instructions.
If you have your OSX installer disk "System Restore" might fix it. If not, there is a Terminal application on the Installer disk that would be easier to use than Single-user mode.
In any case, you are really dealing with one file since the cached file is probably irrelevant. -
HP 4385 all in one returns message "This device not configured for networking"
This happens just after the point in the install when I have attached USB and wireless data seemingly has been transferred to the Printer. This all started when I needed to do a re-install after a Vista upgrade.
I did reset the printer to Factory settings. I am using latest install software from HP Site. I have tried to resolve this with HP CHAT with no luck. Obviously I have tried this install several times now I even tried it with the printer within inches of my router.
Help PleasePrint a Wireless Test from the front of the printer. It will self-test the components of the printer, including its radio.
1. Press the Wireless button on the front of the HP All-in-One.
2. Press the button next to the icon on the display until Wireless Network Test is highlighted, and then press the button next to OK. The Wireless Network Test prints.
Say thanks by clicking "Kudos" "thumbs up" in the post that helped you.
I am employed by HP -
Configure vpn 3030 snmp for cisco works 2000
vpn 3030 snmp error in cisco works 2000
I want to monitor vpn3030 through vpn monitor,so do some config on vpn3030:
1)Configuration | System | Management Protocols | SNMP
enabled port 161
2)Configuration | System | Management Protocols | SNMP Communities
public
3)Administration | Access Rights | Administrators | Modify Properties
snmp modify config
I can telent & http vpn3030,but when I run test in in cisco works 2000(server
configuration|diagnostics|connectivity tools|management station to device)
it said:
Interface Status Test Results
172.16.8.1 DOWN SNMPR failed
sent: 5 recvd: 0 min: 0 max: 0 avg: 0 timeout: 2 size: 91 protocol: snmp_get port: 161
SNMPW failed
sent: 0 recvd: 0 min: 0 max: 0 avg: 0 timeout: 2 size: 0 protocol: snmp_set port: 161
about my vpn3030
Monitoring | System Status Thursday, 10 October 2002 16:40:16
VPN Concentrator Type: 3030
Bootcode Rev: Cisco Systems, Inc./VPN 3000 Concentrator Series Version 2.5.Rel Jun 21 2000
18:57:52
Software Rev: Cisco Systems, Inc./VPN 3000 Concentrator Series Version 3.0.2.Rel Apr 05 2001
20:50:58
Up For: 6d 0:04:27
Up Since: 10/04/2002 16:35:49
RAM Size: 128 MB
There is only a 6509 between cisco works 2000 server and vpn3030,and no restrictions on tcp/ip
flow.
Please help me .thanks in advance.I test it in cw2000 cdone.
This is really a strange question.
the cw2000 server ip address is 10.8.1.122
the vpn3030 's ip address is 172.16.8.1
between them is a 6509, ip address is 10.8.1.201
when I test connectivity between cw2000 server and 6509, everything is good,snmp is ok.
when i test connectivity between cw2000 server and vpn3030, everything is good,except snmp is not response,while use third party snmp program,snmp status is ok!
when I change the cw2000 server's ip address to 172.16.8.3 and connect it directly to vpn3030,test connectivity between cw2000 server and vpn3030 ,everything is good,snmp is ok. -
Cisco works changes ignored when someone leaves config mode
Hi When a user leaves cisco router config mode, a syslog message is triggered pointing to my Cisco works device.
but the changes ignored when someone leaves config mode (i.e., not picked up until the next scheduled archive)
is it possible in cisco works to immediately archive the configuration of router, when someone leaves Config mode?
if yes , can someone guide how to accomplish this?
thank you in advanceHi!
I think you want to use the automatic action for config fetch which comes with ciscoworks, right?
Did you check that the syslog message from the router came to the server?
If yes, is it in the right form? (I think it is)
I have sometimes the problem with this function that the Analyser was full of syslog messages and drops all new syslogs.
There is a thread here in the forum: https://supportforums.cisco.com/thread/2026181?tstart=0
Sven -
Cisco works LMS 3.0.1 does not archiever configuration for cisco 7201 router
Hi All,
We have Cisco works LMS 3.0.1 and it does not archiever configuration for cisco 7201 router.
Any help would be appriciated.
Thanks in advance
SamirHi,
*** Device Details for d0151-100 ***
Protocol ==> Unknown / Not Applicable
Selected Protocols with order ==> TFTP,SSH,HTTPS
Execution Result:
Unable to get results of job execution for device. Retry the job after increasing the job result wait time using the option:Resource Manager Essentials -> Admin -> Config Mgmt -> Archive Mgmt ->Fetch Settings
This is the error while doing syn archieve.
I am not sure about Rtr7000 version but we have latest Rtr7000.
Waiting for your kind reply.
Samir
Maybe you are looking for
-
Using bean.variable for inputText but not getting value
Hi I am using ADF BC JSF 10.1.3.2. I have a search page that has : dropdown1, based on dropdown1, I populate the dropdown 2 and with autosubmit and partialtrigger and also set either of the two search layouts true LAyout 1 based on dropdown1 value, s
-
Where did the "VS Live" post go?
If there is time to delete unpleasant threads, couldn't there be some time left to post a new release date for the public beta, or just say "there will be no public betas, and we estimate final version to be released <whenever>"? /Kim
-
Text shifts slightly at end of fade-in and at the start of fade-out
Hi, I have created text with a crossfade at both ends. I find that my text jitters a bit at the point where the fade-in ends AND at the point where the fade-out begins. How can I get rid of that slight shift? Thanks, Bob
-
External definition import WSDL complex type problem
Hi, i have created a webservice using apache axis and created an external definition for the service. You can see the respective WSDL recognized by XI below. The service takes an array of adresses. Unfortunately, when I want to define the message map
-
My i message will not work for only one contact the rest will
my iphone will send i messages to everyone else but one