Cisco WS-SVC-NAM-2 Upgrade to 6.0.2; cannot access management web page

I upgraded our WS-SVC-NAM-2 which resides on a 6500, from version 5.1.2.1 to 6.0.2, to include patch2 . Everything seemed ok, however, regardless if I enable http or ip http secure server enable, we cannot access the management site with eithrer FireFox or IE. Status bar shows Internal 500 error, in FF shows "Problem Loading Page" The connection to the server was reset while the page was loading. I'm wondering if it has anything to do with Java, or crypto keys? Here are the patches loaded:
Mon May 4 11:51:20 2009 Patch: nam-app.4-0.strong-crypto-patchK9-1-0 Description: Strong Crypto Patch for NAM.
Fri May 6 08:56:59 2011 Patch: nam-app.strong-crypto-patchK9-5.1-0 Description: Strong Crypto Patch for NAM.
Fri Oct 7 06:53:20 2011 Patch: nam-app.strong-crypto-patchK9-5.1.2-1 Description: Strong Crypto Patch for NAM.
Wed Oct 15 14:56:28 2014 Patch: nam-app-patch.6.0-2-patch2 Description: Patch 2 for NAM release 6.0(2)
Successfully enabled web server.
[email protected]# show version
NAM application image version: 6.0(2-patch2)
Maintenance image version: 2.1(5)
NAM Daughter Card Micro code version: 1.34.1.28 (NAM)
BIOS Version: 4.0-Rel 6.0.9
PID: WS-SVC-NAM-2
Memory size: 1024 MB
Disk 0 size: 20 GB
Installed patches:
Any help would be appreciated. Thanks

Hi Ahmed,
****Upgarde procedure keep the Old data and take you you to the New version *******
This is an Upgarde Procedure ,however if you use the --install command during the Upgarde Procedure ,it will wipeout the old data and NAM will be like a factory Installed and then it will upgarded to New Version.
Follow the below link ,in the step 5:
Step 5 Upgrade the NAM application software as follows:
DON NOT USE THIS
root@localhost# upgrade ftp-url
where ftp-url is the FTP location and name of the NAM software image file
or
USE THIS ONE
root@localhost# upgrade ftp-url --install
Note The --install keyword clears and recreates all of the NAM partitions; this action is similar to restoring the factory-default state. If you use the --install keyword, the previously stored reports and data (if any) will be lost.
http://www.cisco.com/en/US/docs/net_mgmt/network_analysis_module_software/5.1/switch/configuration/guide/advcfg.html#wp1035516
IMP :: It is recommended to have 2GB RAM for running 5.x image
Thanks-
Afroz
[Do rate the useful post]

Similar Messages

Hi. I am using a time capsule for few PC s. I have made 5 different account to access time capsule. but in windows when i enter account name and password for one account, i cannot access other accounts, because windows saves username

Hi. I am using a time capsule for few PC s. I have made 5 different account to access time capsule. but in windows when I enter account name and password for one account, i cannot access other accounts, because windows saves username. how can i prevent this from happenning. I really need to access all my accounts and dont want it to save automaticlly.

Why have 5 accounts if you need to access all of them.. just have one account?
Sorry I cannot follow why you would even use the PC to control the Time Capsule. Apple have not kept the Windows version of the utility up to date.. so they keep making it harder and harder to run windows with apple routers.

I cannot type a web page on my iphone5 on the search or enter website name window of safari. as I type w the system brings me back to the phone main screen. This has happened since I updated to the new iOS 8

I cannot type a web page on my iphone5 on the search or enter website name window of safari. as I type w the system brings me back to the phone main screen. This has happened since I updated to the new iOS 8

You haven't mentioned any steps you might have tried to correct this so I'll suggest you try the first troubleshooting step. Reset your iPhone. Press and hold the Home and Sleep/Wake buttons simultaneously until the Apple logo appears. Then release the buttons and let the device restart. No data will be lost doing this. It's like rebooting a computer.

HT1338 My computer is stuck in upgrade of iPhoto and I cannot access iPhoto; what is a solution?

I was upgrading iphoto as suggested by my computer. I have been "stuck" in the upgrade at step 5 of 10 and cannot access iphoto at all. I have retried this step at least 10 times but am continuously "stuck" Any suggestions?

I too have exactly the same problem as described, where it gets stuck at 81% of step 5 of 9 and cannot do anything. I was prompted to update by computer!
No one yet is to offer a solution other than uninstall and pay for iphoto again.

Upgrade LMS 3.2 - Windows cannot access the specified device, path, or file

/* Style Definitions */
table.MsoNormalTable
{mso-style-name:"Tabla normal";
mso-tstyle-rowband-size:0;
mso-tstyle-colband-size:0;
mso-style-noshow:yes;
mso-style-priority:99;
mso-style-qformat:yes;
mso-style-parent:"";
mso-padding-alt:0cm 5.4pt 0cm 5.4pt;
mso-para-margin-top:0cm;
mso-para-margin-right:0cm;
mso-para-margin-bottom:10.0pt;
mso-para-margin-left:0cm;
line-height:115%;
mso-pagination:widow-orphan;
font-size:11.0pt;
font-family:"Calibri","sans-serif";
mso-ascii-font-family:Calibri;
mso-ascii-theme-font:minor-latin;
mso-fareast-font-family:"Times New Roman";
mso-fareast-theme-font:minor-fareast;
mso-hansi-font-family:Calibri;
mso-hansi-theme-font:minor-latin;}
Hello
I'm trying to upgrade from version 3.1 to LMS 3.2, and I downloaded the lms-3-2-Win-eval.exe but when I try to run it I get an error: Windows can not access the specified device, path, or file .You may not have the appropriate permissions to access the item.
I am the administrator user.
I tried and I can install any other program and if I may
I have a Windows 2003 server.
He has this happened to someone else.
Please if you need any more information, ask me.
Thank you very much, greetings

Hi,
Thanks for posting in Windows Server Forum.
As this thread has been quiet for a while, we assume that the issue has been resolved. At this time, we will mark it as ‘Answered’ as the previous steps should be helpful for many similar scenarios. If the issue still persists, please feel free to reply
this post directly so we will be notified to follow it up.
BTW, we’d love to hear your feedback about the solution. By sharing your experience you can help other community members facing similar problems.
Thanks for your understanding and efforts.
Regards.
Dharmesh Solanki
TechNet Community Support

Since upgrading to firefox 4 I cannot access my inbox for tiscali on the talktalk web site, I can still access using Safari

I have logged onto the talktalk website put in my tiscali email address & password, it logs me on but where it usually says you have xxx new emails it say you have undefined new emails but will not go to the inbox. Spoke to talktalk and we realised it was since I upgraded to version 4, so logged in via Safari and it worked OK.

See the work around linked below, posted by NT, it worked for me.
http://www.talktalk.co.uk/forums/showthread.php?t=185113#post2452787

After upgrading to iOS 8.3 cannot access bluetooth settings

I have an 128 gb iPhone 6 and upgraded to the 8.3 update yesterday (4-8-15). Everything seems to be working fine until I wanted to connect my phone to a new vehicle through Bluetooth. Every time I select Bluetooth in the settings menu, it closes the settings screen and back to the main Utilities folder. Bluetooth still seems to be connecting to my current vehicle an other accessories but I cannot add anything new to it.

Greetings djpins2,
After reviewing your post, it sounds like you are having trouble sending messages to a group. I would recommend that you read this article, it may be able to help the issue.
If you can't send or receive messages on your iPhone, iPad, or iPod touch - Apple Support
If you can't send messages to a certain recipient, delete any conversations you have with them and try sending a new message. When you delete a conversation, you won’t be able to recover it.
Thanks for using Apple Support Communities.
Take care,
Mario

While I can access my email webpage after upgrading to Firefox 5 I cannot access my email inbox

We have no problem accessing other web pages such as google or ebay and it is strange that we can get onto our email site but just not get into our inbox for new emails. There are no details given about the inbox contents either - it says 'undefined new mails in your inbox.'

Although the title says "Firefox 4", the page says "Firefox 4 (and above)": [http://www.adam.com.au/firefox4.php Adam Internet - Firefox 4 Webmail Fix].
Does it work?

Cannot load any web pages on all applications after firefox upgrade ,connection ok firewall configured to allow firefox

vista
firefox 3.68
hp pavillion dv6100

I have removed and added firefox in firewall exceptions, no change
I have turned off firewall, still no change
I have reinstalled firefox , no change
I have installed chrome and opera , same outcome
All other computers using this connection are normal
problem is isolated to this particular laptop
thank you for your reply

Firefox 3.6.13 upgrade prints only a small section of a web page on each printed page

Firefox prints as though the left, right, and bottom margins are very large, so that printing occurs in a small rectangle (1" wide x 3" high) centered toward the top of the page. The print preview shows the same small rectangle of text except that it is located at the left of the screen instead of centered. The result is that many paper pages are printed for each web page (e.g., 15 pages to print http://meyerweb.com/eric/articles/webrev/200001/example3.html whereas IE8 prints this in 2 pages). This occurs for all web pages that I have tried to print and is not isolated to a particular web site.
In the print setup, all margins are set to 0.5". I have tried resetting these but it didn't help.

When I do Ctrl+P from within Firefox and then select Properties for the HL-1440 printer driver, the paper size is A4 which gives the printing problem. Changing the paper size to Letter from within Firefox still gives the same problem.
Correction from previous post: Before printing with the LaserJet 4 printer driver (while the HL-1440 driver is still the default), the print-preview shows the small rectangle of text (see the image of my previous post). However, once I print using the LaserJet 4 driver (which prints correctly) then any subsequent print-preview while using the LaserJet 4 driver correctly displays the page (full width and height). Hence, there seems to be some conflict between this version of Firefox and the factory HL-1440 driver.
Note: All printing is done to the same physical printer (Brother HL-1440). In all cases the printer properties are set to Portrait and Shrink-to-fit.

Upgraded from E8 to E10 cannot access img files

Have been looking all over the net for 5 days now trying to find a answer to my question   Adobe help in India simply could not get me from A to B.
The sites I have been reviewing, have solutions at the software level, talking in computer language which means nothing to me. I am not a computer expert at any level other than at the keyboard level, in other words, just a computer user.
My E10 organizer has all of the thumb nails.   However, All photos taken in a vertical format, have yellow question marks. All but a very small number of Photos taken in the horzontal format do not have a ? mark. I cannot reconnect to any of img files.
All of my photo image/files are on a external drive E: Nothing on (photowise) on C: .   All of my attempts to reconnect have failed?
Can some one give me simple sttep by step instruction on how I can reconnect?
Thank you

Hi Ken
Everything appears to have reconnected.............except all photos shot in the vertical position have not reconnected and have yellow question marks.   A very few photos in the horzontal format have the same problem.
I followed your instruction with directing to the E drive to reconnect and everything except the above seems to have hooked out (I have about 3000 photo files) but what has caused the above and how do I reconnect with those?
There is something around 450 files affected
Also the reconnect window.......I really don't understant how to use the darn thing.   There is the left side and the right side neither of which seems to interact with the other.   Can you direct me to an instruction page on how to use the window.?
Thanks
Tom

Cisco's AnyConnect Network Access Manager (NAM)

Hi dears,
I configurate EAP_FAST in Cisco ISE and want wired users authenticate from ISE. I install Network Access Manager Profile Editor and Cisco Anyconnect Security Mobility Client on PC. I configure Network Access Manager when i want to save as that I did not see the . \newConfigFiles folder. Then I did that: Organize’, ‘Folder and Search Options’, ‘Show hidden files, folders, and drives. but in this case i did see the network access manager folder.
I need a to install Cisco’s AnyConnect Network Access Manager (NAM) on PC. HOW I get this soft? I have a smartnet for ISE.
Which email address(to cisco) i must be write to get this soft?
Thanks.

You can download the Network Access Manager module from CCO. This link should work if you have a CCO account.
http://software.cisco.com/download/release.html?mdfid=283000185&softwareid=282364313&release=3.1.05160&relind=AVAILABLE&rellifecycle=&reltype=latest&i=rs
The file name will be similar to anyconnect-win-3.1.05160-pre-deploy-k9.iso. Just unzip the ISO with 7zip or Winrar and you will see the NAM msi file anyconnect-nam-win-3.1.05149-k9.msi.

GRC PC3.0 Task name in work inbox = WI Text - cannot access the task detail

Hi all
We are using PC 3.0 -ECC6 has been upgraded to 6.05
We cannot access PC tasks from the work inbox - this is true for all the users
We can view the task - task name = WI TEXT
Cannot click on the object name to get to task details
Your help will be appreciate in case you face the same kind of issue
Thanks
Joelle

SAP Note 1546241 solved the issue

Cannot access Seagate Thunderbolt drive since upgrade

Just upgraded to Yosemite, now I cannot access my Seagate 3tb Thunderbolt drive. Any suggestions or patches?

Yea that is a problem and expected
If you are not trying to restore from that vault the the easiest thing to do is just to create a new vault with the new setup and abandon the old vault.
As vaults are only a snapshot of the current state of the library there is nothing to lose by doing this.
If you are trying to recover the vault you can try this:
Locate the vault in the Finder
Select the vault (but don;t open it) and do a Get Info on it, Either right click and select Get Info from the menu or else select Get Info from the File menu or press command I (eye)
In the Info window go to the Name and Extension section and change the extension from .apvault to .aplibrary.
Now try double clicking the 'library' in Finder. Aperture should open and ask if you want to update the library. Say yes.
At this point depending on why you recovered the vault you could use it as is or create a new vault from it.

When I upgrade to FF 26 on my PC laptop, I am no longer able to open any web pages on any browser. Help

Whenever I upgrade to FF 26 on my pc laptop I am no longer able to open any web pages on my laptop in any browser. If I reset my system to a previous date I am good to go. Any ideas on what may be going on or how to troubleshoot it? I am not a technical person - btw
My connection to the internet still shows as connected, but I cannot open any web pages.
thanks,
Bill

Is this happening on a computer running Windows (you posted with as Mac)?
If this is an issue on a Windows computer:
It is possible that security software (firewall, anti-virus) blocks or restricts Firefox or the plugin-container process without informing you, possibly after detecting changes (update) to the Firefox program.
Remove all rules for Firefox and the plugin-container from the permissions list in the firewall and let your firewall ask again for permission to get full unrestricted access to internet for Firefox and the plugin-container process and the updater process.
See:
*https://support.mozilla.org/kb/Server+not+found
*https://support.mozilla.org/kb/Firewalls
*https://support.mozilla.org/kb/fix-problems-connecting-websites-after-updating

Cisco WS-SVC-NAM-2 Upgrade to 6.0.2; cannot access management web page

Similar Messages

Maybe you are looking for