CiscoWorks LMS 4.0.1 login issue.

Hello.
We are using CiscoWorks LMS 4.0.1 with TACACS login module enabled.
We have an issue with an account, and only this account. I can successfully login with any other account, newly created also.
I have deleted and created it without success.
Any ideas?
Thanks for help.
Regards.
Andrea

Hello.
We are using CiscoWorks LMS 4.0.1 with TACACS login module enabled.
We have an issue with an account, and only this account. When I try to login into LMS, TACACS server registers a passed authentication but my IE session stops running.
Same issue when I configure CiscoWorks to use the local login module.
Anyway, I can successfully login with any other account, newly created also.
I have deleted and created again without success.
Regards.
Andrea

Similar Messages

  • Ciscoworks LMS 4.0 – Email Notifications Issue

    We currently use Ciscoworks LMS 4.0 with over 1000 devices in the database. I'm a LMS novice. And have been assigned the task of minimising the amount of email notification’s we receive, as if one device goes Operationally Down all devices off that switch also send alerts to the email notification group, which in turn overwhelms the mailbox.
    The ports are configured not to log or send snmp traps.
    no logging event link-status
    no snmp trap link-status
    So any advice on how we can limit these alerts being generated would be much appreciated.
    Thanks in advance.

    Hi Nessie,
    Go to Monitor > Fault Settings > Setup > Fault Device Details
    select the device and click on view  then Click on the hyperlink or the device name\ip address
    that will bring a new window from there click on Interface and chanaged the Managed state from ture to FLASE for those interfaces for which you do not want ALERTS.
    Thanks-
    Afroz
    [Do rate the useful post]

  • Ciscoworks LMS 3.2 SP1 upgrade issue

    Dear all,
    I've recently upgraded our CW 3.2 to 3.2.1 and I'm having a strange issue with HUM application registration with ACS. The privileges options such as 'Super Admin' etc are no longer there! All the privilege options for all of the other LMS components are there, it's just the HUM module! This is having a knock on affect on the server as Common Services DCR is now failing as it reports the System Indentity User configuration as not having all the privileges assigned!
    Anyone else seen this?
    Regards and thanks in advance,
    Col

    So I worked this out. I decided to try and re-register the Ciscoworks applications within ACS. The major issue was that Common Services just refused to talk to the ACS servers. I then remembered that we closed down the tcp port range on the ACS to a manageable number of sockets to firewall. This appartently is the issue, Ciscoworks registration with ACS wont work unless you re-open the port range! Once I did that Ciscoworks re-registered with ACS and I could re-register the applications and HUM was restored back to how it was!

  • Ciscoworks LMS 4.1 Inventory Collection issue

    We are having an issue with device inventory collection when a device or component in a device is replaced. The inventory collection job appears to be successful but the changes to devices or modules are not retreived. Short of deleting an object and adding back in, are there any configuration changes that can be made or patches that can be applied to LMS to pick up these inventory changes?

    Yes, deleting and re-adding the device works. However, changes have been made to multiple devices in the environment and aside from a bulk delete and re-add there is no guarantee that all changes to all devices will be identified and captured. the side effect will be a loss of historical data.
    Are there any options other that deleting and re-adding that will allow the application to identify the inventory changes, or is this a limitation of the product?
    Are there any items we should check to identify a potential underlying issue?

  • Ciscoworks 3.2 login issue with ACS

    Hi All,
    I am facing an issue with login into Ciscoworks portal from the LMS server, which is integrated with ACS tool.
    Now I am unable to login to the portal with the username and password, which is already configured in the ACS server.
    I have ended up with reinstalling the ciscoworks software and restored the backup, still problem persists. Please let me know how to fix it.
    If I again reinstall it, how would I restore the backup - since back restoration again gives the login issue.
    If Im using only the dcrcli exported devices list after the reinstallation, all the devices gets stuck in DFM question status, hence I restored the proper backup. Now I am stuckup. please help.

    You need to sort out your DNS get the lookup and reverse lookup working.
    Say your device is a box with
    Fa 0/0 10.10.1.1
    Lo 0    172.32.1.1
    If you get you dns to resolve the address of port Fa 0/0  (10.10.1.1)  to the DNS "name adevice.yournetwork.com".
    Next you get your DNS to resolve the name "adevice.yournetwork.com" to 172.32.1.1 with happens to be to Lo0 interface of the device
    Then you can get LMS to use the address you want as it is configured in DNS
    Cheers,
    Michel

  • CiscoWorks LMS 2.6: Blank page after login

    Hi,
    CiscoWorks LMS version 2.6 is running on Windows Server 2003. I can load the login page using Internet Explorer. However after login page is blank. I have attached the screenshot(ciscowork.jpg) and pdshow result (pdshow.zip).
    Also there is an error for ANI server: Error: Get reply from Server failed. I have also attached the screenshot (ciscoworks2.jpg) as well, log was also extracted (error_log.txt)
    Please help... Thanks

    Your Services are misconfigured.  Post screenshots of the Services control panel showing all of the CiscoWorks services.

  • CiscoWorks LMS 3.1: HUM and Web access issue...

    /* Style Definitions */
    table.MsoNormalTable
    {mso-style-name:"Table Normal";
    mso-tstyle-rowband-size:0;
    mso-tstyle-colband-size:0;
    mso-style-noshow:yes;
    mso-style-parent:"";
    mso-padding-alt:0in 5.4pt 0in 5.4pt;
    mso-para-margin:0in;
    mso-para-margin-bottom:.0001pt;
    mso-pagination:widow-orphan;
    font-size:10.0pt;
    font-family:"Times New Roman";
    mso-ansi-language:#0400;
    mso-fareast-language:#0400;
    mso-bidi-language:#0400;}
    Hi there,
    I would like to seek your counsel with regards to the recent incident that we encountered with our CiscoWorks LMS 3.1 running on Solaris 10.
    A few days ago, we received a few complains from our users that they were unable to view the pollers or contents of the TOP-N <CPU | Memory | Interface> Utilization on the HUM’s home page (see attached file, hum_homepage.jpg).
    We (tech support guys) checked the pollers’ status and they’re all Active (see attached file, pollers.jpg); we notified our Administrators and requested for a copy of the HUMPortal.log (see attached file, humportal.zip).
    The following day, while waiting for the HUMPortal.log, we received reports that users accessing the HUM home page are stuck with the message “loading…” on all TOP-N Utilization reports.
    As we were about to re-queue our request from our administrators, we received reports (a few hours ago) that our CiscoWorks LMS is inaccessible via web browser.
    We alerted our administrators and they attempted to restart the Daemon Manager (/etc/init.d/dmgmtd); they were able to successfully shut it down but took several attempts to start it up.
    As they attempt to start up the Daemon Manager, they encountered the following error message:
    # /etc/init.d/dmgtd start
    Error: Daemon Management could not start. Trying again
    Error: Unable to bind to port, please check port (42340) state and permissions.
    Error: If the port is in use, please try starting Daemon Manager once it become free.
    After several minutes passed, they were able to start up the Daemon Manager successfully although the CiscoWorks LMS is still inaccessible via web browser.
    We requested for a copy of the “pdshow –brief” log and every daemon (as far as I know) seemed to be working fine but it never hurts to ask for help to verify my findings (see attached file, pdshow0818a.log).
    As of the moment of  this writing, we are still unable to access CiscoWorks LMS via web  browser; any insight or suggestion on the next step to take in  troubleshooting and eventually solving this problem is very much  appreciated.

    The port 42340 issue is most likley not related to the HUM issue you described. The latest log entry you provided indicates "Possible reasons for 'No Data' in HUM Portlets could be either Poller is not configured, or Poller is deactivated, or Poller Failure has occurred, or Summarization job did not start." The error is repeated back to the beginning of the file dated Aug 14 16:39.
    To focus on the HUM issue:
    Did any change occur on or around the 14th that you are aware of?
    Please provide some additional debugs:
    1. Please enable debug for "UPMProcess"
    Log files are stored here: #/var/adm/CSCOpx/log/#
    - HUMPortal.log
    - upm_summarization.log
    - jrm.log
    - upm_process.log
    2. To set log levels:
    *Health and Utilization Monitor > Admin > System Preferences*.
    - Select Log Level Settings.
    - Select the application module from the drop-down list.
    - Select the Debug log level from the Logging Level drop-down list.
    Thanks,
    Nick

  • Ciscoworks LMS 4.0 – Fault Device Details Issue

           We currently use Ciscoworks LMS 4.0 but when I go into,  Monitor > Fault Settings > Setup > Fault Device Details   
           I get the following message (see attached document with screenshot) and being a LMS newbie am unsure what to do? As have tried to search for this
           file but no luck.
           So thanks in advance for any advice.

    Check if the fault management rediscovery page shows device as discovered and known or does it have any errors?
    Are you able to generate any fault management reports and view other pages?
    Just try to reboot the server/restart daemon to see if it is goes away.
    Else it is mostly corrupt FM DB. Which would need to be re-initialized.
    Fault Mgmt reinitialize is very simple task, which doesnt removes a lot of data, except past 31 days of FM history and custom notifications, if configured.
    Thanks
    Vinod
    **Rating Encourages contributors, and its really free. **

  • Custom device prompt in Ciscoworks LMS

    Hello,
    In emerging network infrastructure of our client we decided to use some custom promps at device VTY (SSH and Telnet). Console users are network authenticated by means of ACS, and in case ACS is not reachable, we decided to use login prompts as follows:
    Username(local):
    Password(local):
    In this local mode, when CiscoWorks LMS (3.1) tries to collect configuration of switches, VLAN configuration exactly, we got such error messages in LMS interface:
    TELNET: Failed to establish TELNET  connection to 10.52.0.1 - Cause: Authentication failed on device 3 times. VLAN  Config fetch is not supported using TFTP. Command failed VLAN Config fetch is  not supported using RCP.
    Of course, we have checked the possibility to got from LMS host to these devices by SSH and Telnet, credentials are correct, only login prompts are as described earlier.
    I conclude, we need to tell LMS to accept our custom prompts. Is there any possibility and how to achieve this?

    If you're sure the failure is due to the custom prompt, yes, you can simply follow the steps in the following document to let LMS know about that:
    http://www.cisco.com/en/US/products/sw/cscowork/ps2073/products_tech_note09186a00801442c9.shtml

  • CiscoWorks LMS 4.0.1 - Could not generate the report

    Hello,
    I am running CiscoWorks LMS 4.0.1 since 6 months and I wanted to generate today a report about the interface utilization on 2 Cisco switches (Catalyst 3750G). The corresponding job is created, it runs and then i get "succeeded with info" in the "Run Status" column. When I want to click then on the "View Report" link, I get the following error: "Could not generate the report. Either data is not available for the specified duration or the report job failed."
    I tried the same procedure with 2 other switches but I have got the same result.
    Does anybody has an idea of how I can fix this issue?
    Thanks a lot in advanced.
    Best regards,
    Marc Hoffmann

    Hi Marc,
    I have this problem too. I rebooted my Windows but no solved. You known the service name responsible for this error? You have any other sugestion?
    Thank you !!!

  • Adding Device support/definitions in Ciscoworks LMS 3.2

    Hi All
    I am having some issues adding updated definitions for Cisco C3750X-48PS switches.
    We have ciscoworks LMS 3.2 and I need to update the definition/device support for these switches. We are conducting a network refresh and are having some issues with ciscoworks polling these devices correctly.
    I have looked through the various user guides and searched on google with not much luck as to how to actually do this, the links I have found breifly go into it, but not indepth, and the cisco links I have found, of course have redirects to new pages which bear to resemblance to what is in the original document.  Is there a clear guide out there on how to update the switch definiton in ciscoworks? So I can i can try and do this correctly?
    I am new in my current role and I want to ensure I am doing this correctly. Apologies if this has been asked before.
    thanks                 

    First thing to check is the supported device table for LSM3.2. According to it, the 3750X-48P-S is supported pretty much across the board by the LMS tools.
    So you then need to just make sure you update the RME, CM, DFM and CiscoView device packages to integrate the updates into your server. While you can manually download and install the various packages, this task is more easily accomplished via the application GUI itself.
    In LMS 3.2, updates can be done via the Common Services Software Center. The User Guide (here) tells how to use that area in great details. I usually just select "everything" for updating so as to be fully updated for whatever gets installed (as opposed to trying to pick and choose the minimal set of packages).

  • CiscoWorks LMS 3.2 Won't Start on Windows Server 2008 Enterprise

    All,
    I installed CiscoWorks LMS 3.2 RME on Windows Server 2008 Enterprise and the daemon manager won't start.  The server is a VMware ESX server 4.0.
    I've uninstalled and reinstalled and still nothing.
    I get message "The service is not responding to the control function"
    Has anyone had this issue?
    Stephanie

    There could be several reasons this happens.  Common one in Windows 2008 is the swap is not set properly as it defaults to "Automatically manage paging file size for all drives".  Try setting the swap to 8GB manually or whichever is the recommendation for your current device count as per:
    http://www.cisco.com/en/US/docs/net_mgmt/ciscoworks_lan_management_solution/3.2/install/guide1/prereq.html
    Also make sure the startup services are set this way:
    CiscoWorks ANI database engine: Manual
    CiscoWorks Daemon Manager: Automatic
    CiscoWorks RME NG database engine: Manual
    CiscoWorks Tomcat Servlet Engine: Manual
    CiscoWorks Web Server: Manual
    CWCS Cmf database engine: Manual
    CWCS rsh/rcp service: Automatic
    CWCS syslog service: Automatic
    CWCS tftp service: Automatic
    DFM dfmEpm database engine: Manual
    DFM dfmFh database engine: Manual
    DFM dfmInv database engine: Manual
    Set DEP for "Windows Essential Programs Only" and set an exclusion for CSCOpx in your anti-virus on-access scanning settings.  Note that Windows 2008 R2 versions are not supported.

  • Ciscoworks LMS 3.2 - CS job browser extremely slow

    Hello,
    I have ciscoworks LMS 3.2 on a solaris server with 8 GB of RAM.
    Whenever I try to access Job Browser (CS->Server->Admin->Job Browser), the page is just loading forever. All other links like Backup, Log Rotation, Selftest etc load pretty quickly.
    But opening the Job Browser seems next to impossible. All the processes are up and running, so I am not sure what the root cause might be.
    Please help me if anyone has a solution to this issue.
    Thanks,
    Siva

    Hi Sivarama,
    I had a similar issue when LMS had many jobs ? Did you try to purge them (<30 days, for example) ? 
    Hope it helps,
    Elisabeth

  • CISCOWORKS LMS and CISCOSECURE ACS Authenticate any user with HD role

    Hi:
    We are using CiscoSecure for authentication and authorization for differente apps.
    Specifically, any user already in the ACS database is authenticated to log in CiscoWorks LMS, with HD role (this happens although none of the CiscoWorks apps have been checked for this group). 
    Why is this happening?
    We don´t want that any user (although they are only permitted the HD role) could login.
    Thanks a lot
    Julio

    Follow the ACS integration guide to ensure the group you don't want to have access to LMS have the roles set to "NONE" instead of the default HD roles.
    http://www.cisco.com/en/US/partner/prod/collateral/netmgtsw/ps6504/ps6528/ps2425/prod_white_paper0900aecd80613f62.html

  • CiscoWorks LMS not sending mail

    Hi,
    I have CiscoWorks LMS functionning properly. For some time, I am seeing problems with it sending mail notifications. When it is rebooted, it sends the mail properly but after some time, the mail notifications are not sent.
    Is there a log file to see the issue with the mail sending? I am not sure whether it is a CiscoWorks LMS issue or the mail server (on which i have no access) to try to isolate the problem.
    The last change that I made to the server, that might be a possible cause. I had installed the HP NIC teaming with 2 NIC cards teamed and assuming the IP address of the server.
    I just want to check with the server before proceding to mail server blacklisting or other.
    Thanks in Advance,
    Ashley

    Sorry,
    Hi,
    I have CiscoWorks LMS functionning properly. For some time, I am seeing problems with it is not sending mail notifications. When it is rebooted, it sends the mail properly but after some time, the mail notifications are not sent.
    Is there a log file to see the issue with the mail sending? I am not sure whether it is a CiscoWorks LMS issue or the mail server (on which i have no access) to try to isolate the problem.
    The last change that I made to the server, that might be a possible cause. I had installed the HP NIC teaming with 2 NIC cards teamed and assuming the IP address of the server.
    I just want to check with the server before proceding to mail server blacklisting or other.
    Thanks in Advance,
    Ashley

Maybe you are looking for

  • Multiple devices using iTunes on multiple Windows accounts interchangeably

    I have searched this topic online extensively and have not been able to find a case similar to mine explained. So I am hoping that I can get some assistance here. I have a Windows XP PC with 2 user accounts - one for me and one for my wife. I have 4

  • Satellite l505d-gs6000 hard drive failure?

    hello, am working on a computer for a friend. we both have the toshiba satellite l505d-gs6000. he says he was on google and started to suffer a malware attack and shut off the computer. the computer will no longer boot. trying to boot the computer wi

  • Purchasing music from itunes usa

    Is it possible to puchase music from itunes usa? They have different tracks available,but only send me back to the uk site if i try and buy them,where of course the track does not exist,can't find the track anywhere else either,so hope there is a sol

  • Master Data CONTACT Contact Person

    Hi, Is there any Program/BAPI available for loading the customer contact person info (VAP1) into SAP from lagacy system through LSMW. Thanks, Dhareppa

  • FrameMaker to RoboHelp to EPUB for side notes

    Hi, I have a FrameMaker 10 document with side notes (paragraph style has format "Side Head-Alignment"): I then import into RoboHelp 9 and generate an EPUB document. The result is that the "Note" label is right justified on the body: Can you tell me h