Codec problem with one gateway

I am having a very strange problem with one of my gateways. No matter how I set up my regions and device pools I continue to have all calls go through this gateway as G729. This would be fine except that I can't do conference calls because of codec mismatches.
The gateway is a PRI running H323. CM 3.2.2(c) Gateway is a 3640 running 12.2.11(t)
All regions are currently set to G711.
I read something about a command under voice-port that sets the default codec. What I don't understand is, if this is what is causing it to go to G729, why is this the only gateway that ignores the regions.
Any help would be appreciated.

Cisco VoIP gateways support the codec negotiation feature. This feature provides the ability for a Cisco VoIP gateway to connect to other VoIP devices without necessarily knowing which codec is used for a call-setup. Also, this feature allows Cisco VoIP gateways to dynamically adjust to changes on remote devices. As long as the codec used by the remote VoIP device matches the capabilities-list of the Cisco VoIP gateway, the VoIP call is completed.
The following example shows how to configure codec negotiation:
Cisco-router# config t
Cisco-router(config)# voice class codec 1
!--- This sets up class 1 to be assigned to the dial peer.
Cisco-router(config-class)#codec preference 1 g723r63
Cisco-router(config-class)#codec preference 2 g729ar8
Cisco-router(config-class)#codec preference 3 g711ulaw
Cisco-router(config-class)#codec preference 4 g726r32 bytes 240
!--- These commands define the preferred codec list using 1,2,3, and 4 to set the preference.
Cisco-router(config)#dial-peer voice 1 voip
Cisco-router(config-dial-peer)#voice-class codec 1
!--- This assigns voice-class codec 1 to the dial-peer
Cisco-router(config-dial-peer)#destination-pattern 4723155
Cisco-router(config-dial-peer)#session target ipv4:192.168.100.1

Similar Messages

TS3276 I have recently had a problem with one of my hotmail accounts, some sort of virus sending random emails to people in my address book. Hotmail advised me to change my password for that account, which I did. Why won't mail recognise the new password?

I have recently had a problem with one of my hotmail accounts, some sort of virus sending random emails from my address book. Hotmail advised me to delete all contacts and change the password for that account, which I did on my laptop running windows XP. The change was successful and I was able to send and receive emails with no problem. I then had to change the account password on my iPhone 4s, which I did and it too was successful but when I came to change the password on my iMac, running the latest version of Lion it would not recognise the new password. I have tried to remove the account details and re-install but every time I go to add new account my old details are in the box. This is very frustrating as I use my iMac for all my profects and I need to access my email. Please help.

hi guys,
I had already deleted all reference to the hotmail account in question from the keychain access app, I have also tried to delete and re-instal the account details from within mail. The icon in the side bar dissapears but when I go to Add Account, the old account details are in the new account box. I then input my new password but am told that the server does not recognise it. If I access hotmail via google on the iMac I can get into my account with no problems. I am thinking there must be some other form of security system within the mac software that is blocking the new password. This is driving me nuts. I have been trying to resolve this for the last two days. Thank you for your advise anyway.

Just installed Lion and the Magic TrackPad and I am having a problem with one click commands. I have to hit the pad fairly hard with one finger to get it to accept the command. Is this normal, is there another way that I am suppose to execute commands?

Just installed Lion and the Magic TrackPad and I am having a problem with one click commands. I have to hit the pad fairly hard with one finger to get it to accept the command. Is this normal, is there another way that I am suppose to execute commands?

No you just need to turn on Tap to Click. Go into System Preferences - Trackpad and click the Point to Click tab and select the first box which will say Tap to Click and you should be in business.

Entire JDBC communication stopped if problem with one single JDBC interface

Hello,
Will the entire JDBC communication stopped if problem with one single JDBC interface?
Thanks,
Soorya.

hi surya,
this will happend if u use maintain order at runtime at interface determination.
just uncheck this option if u dont neet EOIO.
if you are getting the problem if u r going for EO then the problem might be using same JDBC channel for all interfaces.
if each interface is expected with a high load then it better to go for dedicated channels for interfaces.
like INTERFACE A should use JDBC A channel and INTERFACE B should use JDBC B channel.
Thanks & Regards,
Rama krishna

JDBC communication stopped if problem with one single JDBC interface

Hello,
Can you please explain this phrase
"JDBC communication stopped if problem with one single JDBC interface"
THanks,
Soorya

If you are having a problem with a JDBC interface (lets consider this to be a communication channel) then the communication is stopped (via that channel) (only in the case of EOIO).
Hope this clarifies.
Cheers,
Sarath
Award if helpful.

LaCie 6TB drive ejects when Air sleeps: I use two 6TB LaCie drives - home and office with my Air, which travels with me. Only have a problem with one. Is there a fix?

LaCie 6TB drive ejects when Air sleeps: I use two 6TB LaCie drives - home and office with my Air, which travels with me between the locations. Only have a problem with one that inappropriately ejects when the Air sleeps (and only sometimes). Is there a fix? I've read others who believe that the problem is with the operating system (I'm using 10.9.2). But my problem suggests that it's with one of the LaCie's. Any suggestions about how to fix?

Lacie doesnt make HD, thats a Seagate inside the box.
Is there a fix?
Yes, get a 4TB max HD, 6TB drives are both new and have known issues, ...in fact so do most all 4TB drives.
my problem suggests that it's with one of the LaCie's
You mean Seagate
Large external hard drives are great! Large external hard drives are horrible
It is a common premise that people are overjoyed at the dropping prices per terabyte on external hard drives, and the first thing that enters most peoples minds is "great, I can put all my stuff on one drive,... all of it!" However considerations need to be made in creating a giant single choke point for not mere data loss, but seriously large data loss. If there is at the very least yet another redundant copy, this is fine, otherwise do not consider it whatsoever. Some 3TB and 4TB drives of all mfg. have, at the time of this writing, reliability concerns currently and best recommendation is staying at 2TB drives or less.
Advantages and disadvantages of larger 3TB and 4TB external drives must be weighed

Problem with one to one unidirectional relation

Hi,
I have one problem with one to one relation ship. While i am trying to persist the objects it is showing that "parent key not found" exception. Is there any problem with my class configuration ?..
Table description:having two tables with same composite primary key
ECommSchema table has one composite primay key and the ECommSchemaDet table also has the same composite primary key. In second table (ECommSchemaDet) composite primary key fields are refering(foreign key relation ship) from the first table.
My entity classes are....
@Entity(name = "E_COMM_SCHEMA")
@Table(name = "E_COMM_SCHEMA", uniqueConstraints = {})
public class ECommSchema extends ParentEntity implements java.io.Serializable{
// Fields
private ECommSchemaDet eCommSchemaDet;
// Constructors
/** default constructor */
public ECommSchema(){
/** minimal constructor */
public ECommSchema(ECommSchemaId id, String descBriefEng, Date effectiveFrom, Currencies currencies){
this.id = id;
this.descBriefEng = descBriefEng;
this.effectiveFrom = effectiveFrom;
this.currencies = currencies;
/** full constructor */
@OneToOne(cascade = { CascadeType.ALL })
@PrimaryKeyJoinColumns({ @PrimaryKeyJoinColumn(name = "COMP_CODE", referencedColumnName = "COMP_CODE"),
@PrimaryKeyJoinColumn(name = "CODE", referencedColumnName = "SCHEMA_CODE") })
public ECommSchemaDet getECommSchemaDet(){
return eCommSchemaDet;
public void setECommSchemaDet(ECommSchemaDet commSchemaDet){
eCommSchemaDet = commSchemaDet;
@SuppressWarnings("serial")
@Entity(name = "E_COMM_SCHEMA_DET")
@Table(name = "E_COMM_SCHEMA_DET", uniqueConstraints = {})
public class ECommSchemaDet implements java.io.Serializable{
private ECommSchema ECommSchema;
// Constructors
/** default constructor */
public ECommSchemaDet(){
/** minimal constructor */
public ECommSchemaDet(ECommSchemaDetId id, ECommSchema ECommSchema, String calcBase, String multiTier, String distMethod,
Double brokerRebate, Double ticketCharge){
this.id = id;
this.ECommSchema = ECommSchema;
this.calcBase = calcBase;
this.multiTier = multiTier;
this.distMethod = distMethod;
this.brokerRebate = brokerRebate;
this.ticketCharge = ticketCharge;
/** full constructor */
public ECommSchemaDet(ECommSchemaDetId id, ECommSchema ECommSchema, String calcBase, String multiTier, String distMethod,
Double brokerRebate, Double ticketCharge, String distMethodClient){
this.id = id;
this.ECommSchema = ECommSchema;
this.calcBase = calcBase;
this.multiTier = multiTier;
this.distMethod = distMethod;
this.brokerRebate = brokerRebate;
this.ticketCharge = ticketCharge;
this.distMethodClient = distMethodClient;
// Property accessors
@OneToOne(cascade = { CascadeType.REFRESH }, fetch = FetchType.EAGER, mappedBy = "eCommSchemaDet")
public ECommSchema getECommSchema(){
return this.ECommSchema;
public void setECommSchema(ECommSchema ECommSchema){
this.ECommSchema = ECommSchema;
Error message is
Local Exception Stack:
Exception [TOPLINK-4002] (Oracle TopLink Essentials - 2.0.1 (Build b09d-fcs (12/06/2007))): oracle.toplink.essentials.exceptions.DatabaseException
Internal Exception: java.sql.SQLException: ORA-02291: integrity constraint (ETRADE_4BM.FK_ECOMM_SCH_DET) violated - parent key not found
Error Code: 2291
Call: INSERT INTO E_COMM_SCHEMA_DET (DIST_METHOD, BROKER_REBATE, CALC_BASE, TICKET_CHARGE, DIST_METHOD_CLIENT, MULTI_TIER, SCHEMA_CODE, COMP_CODE) VALUES (?, ?, ?, ?, ?, ?, ?, ?)
     bind => [T, 23.0, A, 23.0, T, N, 8, 1]
Query: InsertObjectQuery(com.path.tradeManager.entities.ECommSchemaDet@44fbf5)
     at oracle.toplink.essentials.exceptions.DatabaseException.sqlException(DatabaseException.java:311)
     at oracle.toplink.essentials.internal.databaseaccess.DatabaseAccessor.executeDirectNoSelect(DatabaseAccessor.java:654)
     at oracle.toplink.essentials.internal.databaseaccess.DatabaseAccessor.executeNoSelect(DatabaseAccessor.java:703)
     at oracle.toplink.essentials.internal.databaseaccess.DatabaseAccessor.basicExecuteCall(DatabaseAccessor.java:492)
     at oracle.toplink.essentials.internal.databaseaccess.DatabaseAccessor.executeCall(DatabaseAccessor.java:452)
     at oracle.toplink.essentials.internal.sessions.AbstractSession.executeCall(AbstractSession.java:690)
     at oracle.toplink.essentials.internal.sessions.IsolatedClientSession.executeCall(IsolatedClientSession.java:150)
     at oracle.toplink.essentials.internal.queryframework.DatasourceCallQueryMechanism.executeCall(DatasourceCallQueryMechanism.java:228)
     at oracle.toplink.essentials.internal.queryframework.DatasourceCallQueryMechanism.executeCall(DatasourceCallQueryMechanism.java:214)
     at oracle.toplink.essentials.internal.queryframework.DatasourceCallQueryMechanism.insertObject(DatasourceCallQueryMechanism.java:346)
     at oracle.toplink.essentials.internal.queryframework.StatementQueryMechanism.insertObject(StatementQueryMechanism.java:191)
     at oracle.toplink.essentials.internal.queryframework.StatementQueryMechanism.insertObject(StatementQueryMechanism.java:205)
     at oracle.toplink.essentials.internal.queryframework.DatabaseQueryMechanism.insertObjectForWrite(DatabaseQueryMechanism.java:564)
     at oracle.toplink.essentials.queryframework.InsertObjectQuery.executeCommit(InsertObjectQuery.java:89)
     at oracle.toplink.essentials.internal.queryframework.DatabaseQueryMechanism.performUserDefinedWrite(DatabaseQueryMechanism.java:750)
     at oracle.toplink.essentials.internal.queryframework.DatabaseQueryMechanism.performUserDefinedInsert(DatabaseQueryMechanism.java:714)
     at oracle.toplink.essentials.internal.queryframework.DatabaseQueryMechanism.insertObjectForWriteWithChangeSet(DatabaseQueryMechanism.java:602)
     at oracle.toplink.essentials.queryframework.WriteObjectQuery.executeCommitWithChangeSet(WriteObjectQuery.java:162)
     at oracle.toplink.essentials.internal.queryframework.DatabaseQueryMechanism.executeWriteWithChangeSet(DatabaseQueryMechanism.java:390)
     at oracle.toplink.essentials.queryframework.WriteObjectQuery.executeDatabaseQuery(WriteObjectQuery.java:109)
     at oracle.toplink.essentials.queryframework.DatabaseQuery.execute(DatabaseQuery.java:628)
     at oracle.toplink.essentials.queryframework.DatabaseQuery.executeInUnitOfWork(DatabaseQuery.java:555)
     at oracle.toplink.essentials.queryframework.ObjectLevelModifyQuery.executeInUnitOfWorkObjectLevelModifyQuery(ObjectLevelModifyQuery.java:138)
     at oracle.toplink.essentials.queryframework.ObjectLevelModifyQuery.executeInUnitOfWork(ObjectLevelModifyQuery.java:110)
     at oracle.toplink.essentials.internal.sessions.UnitOfWorkImpl.internalExecuteQuery(UnitOfWorkImpl.java:2233)
     at oracle.toplink.essentials.internal.sessions.AbstractSession.executeQuery(AbstractSession.java:952)
     at oracle.toplink.essentials.internal.sessions.AbstractSession.executeQuery(AbstractSession.java:909)
     at oracle.toplink.essentials.internal.sessions.CommitManager.commitNewObjectsForClassWithChangeSet(CommitManager.java:269)
     at oracle.toplink.essentials.internal.sessions.CommitManager.commitAllObjectsForClassWithChangeSet(CommitManager.java:246)
     at oracle.toplink.essentials.internal.sessions.CommitManager.commitAllObjectsWithChangeSet(CommitManager.java:202)
     at oracle.toplink.essentials.internal.sessions.AbstractSession.writeAllObjectsWithChangeSet(AbstractSession.java:2657)
     at oracle.toplink.essentials.internal.sessions.UnitOfWorkImpl.commitToDatabase(UnitOfWorkImpl.java:1044)
     at oracle.toplink.essentials.internal.ejb.cmp3.base.RepeatableWriteUnitOfWork.commitToDatabase(RepeatableWriteUnitOfWork.java:403)
     at oracle.toplink.essentials.internal.sessions.UnitOfWorkImpl.commitToDatabaseWithPreBuiltChangeSet(UnitOfWorkImpl.java:1160)
     at oracle.toplink.essentials.internal.ejb.cmp3.base.RepeatableWriteUnitOfWork.writeChanges(RepeatableWriteUnitOfWork.java:276)
     at oracle.toplink.essentials.internal.ejb.cmp3.base.EntityManagerImpl.flush(EntityManagerImpl.java:350)
     at com.sun.enterprise.util.EntityManagerWrapper.flush(EntityManagerWrapper.java:626)
     at com.path.tradeManager.dao.ECommSchemaDaoBean.save(ECommSchemaDaoBean.java:86)
     at sun.reflect.NativeMethodAccessorImpl.invoke0(Native Method)
     at sun.reflect.NativeMethodAccessorImpl.invoke(NativeMethodAccessorImpl.java:39)
     at sun.reflect.DelegatingMethodAccessorImpl.invoke(DelegatingMethodAccessorImpl.java:25)
     at java.lang.reflect.Method.invoke(Method.java:597)
     at com.sun.enterprise.security.application.EJBSecurityManager.runMethod(EJBSecurityManager.java:1067)
     at com.sun.enterprise.security.SecurityUtil.invoke(SecurityUtil.java:176)
     at com.sun.ejb.containers.BaseContainer.invokeTargetBeanMethod(BaseContainer.java:2895)
     at com.sun.ejb.containers.BaseContainer.intercept(BaseContainer.java:3986)
     at com.sun.ejb.containers.EJBObjectInvocationHandler.invoke(EJBObjectInvocationHandler.java:203)
     at com.sun.ejb.containers.EJBObjectInvocationHandlerDelegate.invoke(EJBObjectInvocationHandlerDelegate.java:117)
     at $Proxy133.save(Unknown Source)
     at sun.reflect.NativeMethodAccessorImpl.invoke0(Native Method)
     at sun.reflect.NativeMethodAccessorImpl.invoke(NativeMethodAccessorImpl.java:39)
     at sun.reflect.DelegatingMethodAccessorImpl.invoke(DelegatingMethodAccessorImpl.java:25)
     at java.lang.reflect.Method.invoke(Method.java:597)
     at com.sun.corba.ee.impl.presentation.rmi.StubInvocationHandlerImpl.privateInvoke(StubInvocationHandlerImpl.java:233)
     at com.sun.corba.ee.impl.presentation.rmi.StubInvocationHandlerImpl.invoke(StubInvocationHandlerImpl.java:152)
     at com.sun.corba.ee.impl.presentation.rmi.bcel.BCELStubBase.invoke(BCELStubBase.java:225)
     at com.path.tradeManager.daoInterface.__ECommSchemaDaoInterface_Remote_DynamicStub.save(com/path/tradeManager/daoInterface/__ECommSchemaDaoInterface_Remote_DynamicStub.java)
     at com.path.tradeManager.daoInterface._ECommSchemaDaoInterface_Wrapper.save(com/path/tradeManager/daoInterface/_ECommSchemaDaoInterface_Wrapper.java)
     at sun.reflect.NativeMethodAccessorImpl.invoke0(Native Method)
     at sun.reflect.NativeMethodAccessorImpl.invoke(NativeMethodAccessorImpl.java:39)
     at sun.reflect.DelegatingMethodAccessorImpl.invoke(DelegatingMethodAccessorImpl.java:25)
     at java.lang.reflect.Method.invoke(Method.java:597)
     at com.path.tradeManager.tunnelGate.RequestHandler.callMethodByReflection(RequestHandler.java:181)
     at com.path.tradeManager.tunnelGate.RequestHandler.handle(RequestHandler.java:150)
     at com.path.tradeManager.tunnelGate.TunnelServlet.doPost(TunnelServlet.java:37)
     at javax.servlet.http.HttpServlet.service(HttpServlet.java:738)
     at javax.servlet.http.HttpServlet.service(HttpServlet.java:831)
     at org.apache.catalina.core.ApplicationFilterChain.servletService(ApplicationFilterChain.java:411)
     at org.apache.catalina.core.StandardWrapperValve.invoke(StandardWrapperValve.java:290)
     at org.apache.catalina.core.StandardContextValve.invokeInternal(StandardContextValve.java:271)
     at org.apache.catalina.core.StandardContextValve.invoke(StandardContextValve.java:202)
     at org.apache.catalina.core.StandardPipeline.doInvoke(StandardPipeline.java:632)
     at org.apache.catalina.core.StandardPipeline.doInvoke(StandardPipeline.java:577)
     at com.sun.enterprise.web.WebPipeline.invoke(WebPipeline.java:94)
     at org.apache.catalina.core.StandardHostValve.invoke(StandardHostValve.java:206)
     at org.apache.catalina.core.StandardPipeline.doInvoke(StandardPipeline.java:632)
     at org.apache.catalina.core.StandardPipeline.doInvoke(StandardPipeline.java:577)
     at org.apache.catalina.core.StandardPipeline.invoke(StandardPipeline.java:571)
     at org.apache.catalina.core.ContainerBase.invoke(ContainerBase.java:1080)
     at org.apache.catalina.core.StandardEngineValve.invoke(StandardEngineValve.java:150)
     at org.apache.catalina.core.StandardPipeline.doInvoke(StandardPipeline.java:632)
     at org.apache.catalina.core.StandardPipeline.doInvoke(StandardPipeline.java:577)
     at org.apache.catalina.core.StandardPipeline.invoke(StandardPipeline.java:571)
     at org.apache.catalina.core.ContainerBase.invoke(ContainerBase.java:1080)
     at org.apache.coyote.tomcat5.CoyoteAdapter.service(CoyoteAdapter.java:272)
     at com.sun.enterprise.web.connector.grizzly.DefaultProcessorTask.invokeAdapter(DefaultProcessorTask.java:637)
     at com.sun.enterprise.web.connector.grizzly.DefaultProcessorTask.doProcess(DefaultProcessorTask.java:568)
     at com.sun.enterprise.web.connector.grizzly.DefaultProcessorTask.process(DefaultProcessorTask.java:813)
     at com.sun.enterprise.web.connector.grizzly.DefaultReadTask.executeProcessorTask(DefaultReadTask.java:341)
     at com.sun.enterprise.web.connector.grizzly.DefaultReadTask.doTask(DefaultReadTask.java:263)
     at com.sun.enterprise.web.connector.grizzly.DefaultReadTask.doTask(DefaultReadTask.java:214)
     at com.sun.enterprise.web.portunif.PortUnificationPipeline$PUTask.doTask(PortUnificationPipeline.java:380)
     at com.sun.enterprise.web.connector.grizzly.TaskBase.run(TaskBase.java:265)
     at com.sun.enterprise.web.connector.grizzly.ssl.SSLWorkerThread.run(SSLWorkerThread.java:106)
Caused by: java.sql.SQLException: ORA-02291: integrity constraint (ETRADE_4BM.FK_ECOMM_SCH_DET) violated - parent key not found
     at oracle.jdbc.driver.DatabaseError.throwSqlException(DatabaseError.java:124)
     at oracle.jdbc.driver.T4CTTIoer.processError(T4CTTIoer.java:304)
     at oracle.jdbc.driver.T4CTTIoer.processError(T4CTTIoer.java:271)
     at oracle.jdbc.driver.T4C8Oall.receive(T4C8Oall.java:622)
     at oracle.jdbc.driver.T4CPreparedStatement.doOall8(T4CPreparedStatement.java:180)
     at oracle.jdbc.driver.T4CPreparedStatement.execute_for_rows(T4CPreparedStatement.java:542)
     at oracle.jdbc.driver.OracleStatement.doExecuteWithTimeout(OracleStatement.java:1027)
     at oracle.jdbc.driver.OraclePreparedStatement.executeInternal(OraclePreparedStatement.java:2887)
     at oracle.jdbc.driver.OraclePreparedStatement.executeUpdate(OraclePreparedStatement.java:2959)
     at oracle.toplink.essentials.internal.databaseaccess.DatabaseAccessor.executeDirectNoSelect(DatabaseAccessor.java:647)
     ... 92 more
Jul 8, 2008 4:17:07 PM com.sun.enterprise.server.logging.SystemOutandErrHandler$LoggingByteArrayOutputStream flush
INFO: FATAL[08-07-08 16:17:07][com.path.tradeManager.dao.ECommSchemaDaoBean->save][javax.persistence.PersistenceException: Exception [TOPLINK-4002] (Oracle TopLink Essentials - 2.0.1 (Build b09d-fcs (12/06/2007))): oracle.toplink.essentials.exceptions.DatabaseException
Internal Exception: java.sql.SQLException: ORA-02291: integrity constraint (ETRADE_4BM.FK_ECOMM_SCH_DET) violated - parent key not found
Thanks in advance
Anish

Hello,
I'm not sure what the FK_ECOMM_SCH_DET constraint refers to, but I assume it is to the only OneToOne reference defined. Based on the mappings shown, you have told TopLink that ECommSchema has a 1:1 to ECommSchemaDet, so that ECommSchemaDet has to be inserted first. My guess is your constraint is the oposite, requiring that ECommSchema be inserted before ECommSchemaDet. If so, just change the by directional 1:1 so that ECommSchema->ECommSchemaDet is mapped by the ECommSchemaDet->ECommSchema relationship (ie switch things).
Best Regards,
Chris

Problem with one computer: [RegTask] - Server rejected registration request: 3

Hi!
I having some problem with One of our clients, its mine :)
It does not register with the site
ClientIDManagerStartup.log:
MP_RegistrationManager.log
I have no idea why! I don't even use https and PKI. I have done a reinstalled the client by removing "C:\windows\SMSCFG.ini" and the SMS certificates before install but it still won't register. CCMSetup logs return successfull. Boundaries is setup
correctly.
I have also tried to uninstall ccmagent and readded the computer object in SCCM and installed it through client push but still the same problem.
I really don't want to reinstall the whole computer as I have already installed lots of applications i don't know if that will work anyway, could try to run a sysprep maybe.
Any ideas?
Thanks!

if that is the error you need to look at your IIS & Webdav & SQL Configurations... you can take some help from below blogs to troubleshoot this
http://anoopmannur.wordpress.com/2011/04/20/configmgr-sccm-2007-mpcontrol-log-shows-httpsendrequestsync-fails-with-status-code-500-internal-server-error/
http://www.windows-noob.com/forums/index.php?/topic/651-sccm-mp-issues/
http://windows7sux.blogspot.com/2009/04/sccm-smp-500-error.html
http://brothertu.blogspot.com/2010/07/how-to-quickly-test-to-see-if-sccm-mp.html
http://social.technet.microsoft.com/Forums/en-US/configmgrsetup/thread/89c84077-f47c-427b-b73e-39478f34ebaf/
Thanks, Prabha G

Problem with One-Step Approval of Contracts ws14000088

Hi, I have a problem with the One-Step Approval of Contracts ws14000088, the workflow can't find approverat the task TS14007969
regards
Dayana

Hi
<b>Please go through these links, which will definitely help -></b>
Which SRM version are you using ?
Re: Problem with one step approval contract workflow
Re: No Approver(s) Found
Reminders for work item
Re: How to add a new field to the notification mail
Do let me know.
Regards
- Atul

WLC 2504 problems with one IP address range

I am having an interesting issue configuring a new 2504.
How it is setup:
Port 1 management with vlan tagging on vlan 111
Port 2 trunking with ap-manager2 on vlan 3, 102 on vlan 102 (Not ap-manager), and 1001 on vlan 1001.
All of the vlans have distinctive and unique IP ranges. Vlan 111 is running 172.16.128 /20, 102 is 172.19.252 /23 and vlan 1001 should be running 172.17 /16.
Here is my problem. I can setup all of the dynamic interfaces on the appropriate ip ranges, but for some reason when I configure the 1001 vlan dynamic interface with the /16 address space, I lose connectivity to the GUI managment interface. I have to go in through the CLI and remove the interface or change the IP range. I have tried other /16 address space on that vlan and do not have a problem with them. the 172.17 space appears to be the only one that will not work.
I have attached the config from the controller (Minus some site specific stuff like the SNMP community and wpa stuff.) The config is using a 172.20 /16 right now on the 1001 interface so that I could get into the controller and download the config. It should be 172.17 /16. The acutal IP info should be 172.17.4.253 255.255.0.0 172.17.0.254
My computer is on the 1001 vlan and I have verified the IP is not in use and am using the same subnet, gateway etc as I am trying to configure the wlc with.
Switch config:
Port 1 is plugged into g0/2 with the following config
interface GigabitEthernet0/2
switchport trunk allowed vlan 1,3,102,111,1001
switchport mode trunk
spanning-tree portfast
Port 2 is plugged into fa0/47 and just has switchport mode trunk.
How can I get the interface to work with the proper IP range for vlan 1001?

I finally had a chance to fiddle around with this issue again and have some more information on the problem. It appears to not be an issue with the IP address, but rather with the VLAN. The 172.17.0.0/16 subnet is on VLAN 1001 which it appears the WLC does not care for. This problem is repeatable on the following versions of code that I have tried:
7.0.220.0
7.1.91.0
7.4.110.0 (Not in use for production until we upgrade from WCS to Prime.)
Any thoughts? Moving the 1001 VLAN to another number would be a HUGE undertaking so if there is not an answer within the firmware on the WLC, I will have to bridge two VLANs with bpdufilter enabled... Not my first choice for sure...

Problem with H323 gateway

We have a CUCM ver 8.6.2.22900-9.
For our PSTN access we have the following scheme:
CUCM <========> Cisco2911 <======> ISP-------> PSTN
H323 tk SIP tk
Our Cisco2911 is running ver 150-1.M4.
We configure Cisco 2911 as H323 gateway on CUCM, and we established a SIP tk with our ISP.
When we tested incoming calls we received them at router but they are unable to acceess CUCM,
When we tested outgoing calls we got reorder tone and they did not reach our voice gateway.
We run "debug cch323 all" and tested with one incoming and one outgoing call, and we got the out on attached file "debug h323 forum"
CUCM Ip : 10.1.2.2
Router's H323 int: 10.2.2.1
Do you have any idea about the root cause?
Can be an access list problem preventing proper H323 traffic??
Thanks in advanced
Enrique

Do you have voip dial-peers pointing back to your cucm from your gateway? If not then the call wouldn't route onward to the cucm, but the gateway would also ignore communications from that souce because of toll fraud prevention.
http://www.cisco.com/c/en/us/support/docs/voice/call-routing-dial-plans/112083-tollfraud-ios.html

Problem with Mobile Gateway 1.0 Configuration

reffering to the config guide for mobile gateway 1.0 (https://websmp102.sap-ag.de/~sapdownload/011000358700000518422009E/Config_Guide_MGW_SP01_rev.pdf) we are facing some problems with the configuration in the DOE.
In Chapter 4.1.1.4 a SWCV "MAS_SMARTPHONE" is mentioned, which is not available in our System, though all other steps before have been successfully executed.
We are on SP08 and SWCV "SAP BASIS 7.10" is activated and generated.
Does anyone know a workaround?
Thanks in advance

i think i located the problem in the DOE.
When a new device is registered (by user-login from device) some LUW's are listed in the SMQ2 for that Queue. Here several dumps occur:
--> 100 ABBTO RR014013005_DRFILLING_006 MMW_RR_RR014013005 05.11.2009 18:19:51 Syntax error in program
ZDOECL_013_005_STRWRPR==== 0A0A001710804AF2FB270034
0A0A001710804AF2FB270034 bgw23
--> 100 ABBTO RR014013002_DEPQ_SERVICE MMW_RR_RR014013002 05.11.2009 18:19:53 Syntax error in program
ZDOECL_013_002_STRWRPR==== 0A0A001710604AF2FB29000E
0A0A001710604AF2FB29000E bgw23
From ST22:
Error in the ABAP application program.
The current ABAP program "SAPLSMMW_STRWRAPPER_APIS" had to be interrupted
because it contains
a statement that cannot be executed.
In the include "ZDOECL_013_002_STRWRPR========CM001 " in the line 21 of program
"ZDOECL_013_002_STRWRPR========CP " the following syntax
errors occur:
"Field "INIT_FLAG" is unknown. It is neither in one of the specified ta"
"bles nor defined by a "DATA" statement. "DATA" statement."

Network problem with one particular iMac in a home network

I want to report a problem involving one particular iMac (2008 Al 24").
On my home network (Apple Airport Extreme and Express extensions, about five Macs and couple of iDevices), all other Macs can see and connect to each other as well as printing to the networked Brother printer without problem.
However, on one particular iMac, I can see all other Macs, can set Brother printer as default with green dot next to it in Print Preference Pane, but I can not connect to other macs, nor print to the printer. Meanwhile, the iMac can get on the internet without any problem. I checked Share Preference Pane and all settings are same as other macs.
The iMac used to work flawlessly until recently, and I first noticed the problem because I could not print, getting a message the printer can not be found (and the dots turn yellow for a while then went back to normal green). Then, I found neither the iMac, nor other macs on the network can connect to each other, even though I can see all of them in Finder.
I opened Apple Remote Network on my own mac, and I can see and connect all other shared macs, but this iMac's status showed not online, even though the IP adress is valid. As a results, no other macs can connect to the iMac, either. It seems to be a problem with the intranet only, not internet.
One more thing, about a month ago, the iMac popped out a warning about network name, saying the old name was in use (conflict) in the network, so I have to change it in Share Pane. Not sure if this is related to the intranet problem.
Reboot and repaired permission several times, no change. Hate to reinstall everything. Any help would be greatly appreciated.

Another update:
For unknown reason, my iMac was suddenly back onto the home "intranet". It can be accessed by my MacBook Air through Finder Connect, and can also be seen by Apple Remote Desktop.
However, printing is still a problem while other macs have no problem printing to the same printer. Whenever I send a print task, either Word document, or other programs such as GraphicConverter image, the iMac tried to connect to the default printer, but failed, and wanted to try again in 30 seconds 9and continued to fail). Meanwhile, the green dot next to the printer selection turned to yellow in Preference Pane. But as soon as I cancel the print job, the printer status went back to normal green.
The printer is a Brother color laser HL-4070CDW, connected through wireless (g only), with it own DHCP but specific IP address. I printed out a setting for the printer and all looks normal, and all other macs can print to it without problem. Other macs can also get access to the printer profile, and check inks copy counts, etc, but the iMac cannot.
Only thing changed since last post was a new update for Apple Airport firmware (to 7.5.2 I think). So my problem is still half solved: can connect to other macs on the same network, but still not be able to print.

Problem with RD gateway manager

Hi,
Have some problems with manager. It used to work, but suddenly I can't connect to local server.
Get this error:
"The RD Gateway Managment snap-in console cannot connect to the server. To connect to this server, you must be a memeber of the local administrators group on the server."
The user account that i'm using is a member of the local administrator group.
Any ideas?
The RDS server is a Win2012 server. The AD server is a win 2008 R2 server.
Thanks
\Kent

Hi Kent,
Thanks for your comment.
For this you need to create RD Rap and RD CAP policies. When you create the RD RAP, add the user groups that you defined in the RD CAP. Also, create a new RD Gateway-managed computer group that contains both the NetBIOS names and the fully qualified domain
names (FQDNs) of the RD Session Host servers or the RD Session Host server farm that hosts the RemoteApp programs.
Please check below article for information.
1. Remote Desktop Gateway Manager
2.How To Work with RD Gateway in Windows Server 2012
Hope it helps!
Thanks.
Dharmesh Solanki

Problem with one box

One box in my house is not getting all channels and other channels are digitized. All other boxes are fine. Rebooting does not help. Ideas?

Could be a problem with the connection. Make sure everything is tight both at box and at splitter.
If that doesn't help, swap the boxes around. If problem follws, you have a bad box, if not, still a problem with that coax run. Could also try swapping ports on the splitter.
If a forum member gives an answer you like, give them the Kudos they deserve. If a member gives you the answer to your question, mark the answer as Accepted Solution so others can see the solution to the problem.

Codec problem with one gateway

Similar Messages

Maybe you are looking for