Computer Has No IP Address
I go to: System Preferences/Network/Show Tab Built in Ethernet/TCP/IP, and type in the configuration, and click the Apply buttonbut when I change the Show Tab to Network Status, it reports:
"The cable for Built-in Ethernet is connected, but your computer does not have an IP address and cannot connect to the internet.
I'm on a Dual boot G4. When booted into OS 9, everything works, but when I re-boot into OX 10.4.6, I always am told the computer has no IP address.
How do I give the computer an IP address in OS 10.4.6? I'm not even trying to connect to the internet, I'm just trying to network to another Mac without Firewire
You didn't state this clearly, so I'll ask -
In Show Built-in ethernet > TCP/IP tab, did you set Configure IPv4 Manually, and then enter a valid local-only IP address, like 192.168.1.5?
As you have seen, without an IP address, OS X acts like ethernet is Off.
The other computer should be given an address in the same subnet, like 192.168.1.6.
Does that help?
Similar Messages
-
Message that another computer has same ip address
......
Check the connection settings.
*Tools > Options > Advanced > Network : Connection > Settings
*https://support.mozilla.org/kb/Options+window+-+Advanced+panel
If you do not need to use a proxy to connect to internet then try to select "No Proxy" if "Use the system proxy settings" or one of the others do not work properly.
See "Firefox connection settings":
*https://support.mozilla.org/kb/Firefox+cannot+load+websites+but+other+programs+can -
My computer has been infected by a Trojan Horse. It has taken over my Mac email account and began sending out malicious emails to everyone in my address book. I cleared out my MAC address book and began using my AOL email account. It took a few days and then my AOL email account was infected and has now been send out malicious email to all my contacts for over a month. It has also infected my iPhone--I am no longer able to send or receive emails on my iPhone. Also, once the Trojan Horse began using my AOL email it completely blocked me from using my MAC account by sending never ending popups asking for my email password to access my MAC email account, but it never accepts my pass word. The TH has also slowed down everything on my computer. It's like I am working on an old PC with dial up connection instead of the high speed digital connection that I have. The little color wheel spins constantly as I wait for sometimes over a minute for a page to pull up. If it pulls up at all. I have tried to use the 2 disks that came with my computer to completely remove everything on my computer and then reinstall all the programs, but I am not allowed to sweep my computer clean. I thought maybe my disks that came with my computer were defective so I called Apple and they sent me 2 new disks. I am not able able to clear my computer with the 2 new disks either. I have done this before successfully so it's not something new to me. I do remember when I believe my computer became infected: I had googled an unusual sewing term, and I was opening what appeared to be legitimate sites, when all of a sudden a pop up appeared that said that my computer had been infected. I immediately shut my computer off, but it was too late. I downloaded a virus program for Mac, and it has never found a virus or problem at all. I think it is part of this Trojan Horse, but I am unable to delete it from my computer. It refuses to uninstall. The Mac Trojan Horse is real and it is terrible. If anyone has any suggestions for me I would be very appreciative,
Beth
vuInstall ClamXav and run a scan with that. It should pick up any trojans.
17" 2.2GHz i7 Quad-Core MacBook Pro 8G RAM 750G HD + OCZ Vertex 3 SSD Boot HD
Got problems with your Apple iDevice-like iPhone, iPad or iPod touch? Try Troubleshooting 101 -
My iPad has a different Apple ID than the Apple ID on my computer. The iPad Apple ID has an email address that I no longer use. If (while on the iPad) I go to My Apple ID and try to change or add the email address that I now use (and which already is my Apple ID on the computer), it won't allow me to add it. It says : "Email address is already verified for another Apple ID" I haven't really been aware of this as a problem until I tried (for the first time) to sync my iPad to the computer and became aware that certain things wouldn't transfer. What is the solution to this?
What are you having problems with ?
This post was about having updated the primary email address on an iTunes account via a computer - if you do that you might need to log out of the account on an iPad by tapping on the id in Settings > iTunes & App Store and then log back in with the updated version of the account for that email address change to be recognised on your iPad. If you don't log out and back in then an iPad (or iPhone or iPod Touch) might continue to show the old version of the iTunes account id. -
I have an older IPOD that has not been synced to Itunes for seceral yeras. I no longer have the same computer or e-mail address. How can I sync my old IPOD material to my new Itunes account?
Your email address (used as your Apple ID) does not matter, because iPods are not directly linked to a particular Apple ID.
NOTE: You can still use your old Apple ID, even if your that email address is no longer valid. As long as you remember your Apple ID password. Go here and click on Manage your Apple ID.
https://appleid.apple.com/cgi-bin/WebObjects/MyAppleId.woa/
You can change the primary email address used by Apple, although the Apple ID remains the same.
Back to the iPod. iTunes syncing is generally in one direction only, from the computer's iTunes library to the iPod. You cannot use iTunes to transfer song files from iPod to computer, except for songs purchased from the iTunes Store. However, there are third-party methods and utilities that can transfer from iPod to computer. If you do an Internet search on something like "ipod transfer," you should get some links. (The CNET article seems to be popular.)
Once the song files are on your computer's drive, you can add them to your new iTunes library. After confirming everything is there, sync your iPod to that library. If there is any content purchased from the iTunes Store that uses DRM (copy protection), such as audiobooks, videos, and very old song purchases, iTunes may prompt you to authorize your computer with your Apple ID (the one you used to make the purchases). -
Your computer has shut down because of a problem
Hi there,
I have a Macbook Air which is about 3 months old now, and in the last couple of months, applications have started hanging, the keyboard is sluggish in Safari, and more specifically, I've had loads of times when I've opened the lid after the machine has been on sleep, and received the message "Your computer has shut down because of a problem".
I've been on to Apple support, and they took me through how to repair disk permissions, reset the System Management Controller, and clear the caches. But I just had the same thing this morning.
The latest kernel panic from the Console is shown below - is anyone able to shed any light on this?
Thanks
Stuart
Sun Jan 20 02:12:31 2013
panic(cpu 2 caller 0xffffff8005ab7e75): Kernel trap at 0xffffff8005a43ca1, type 14=page fault, registers:
CR0: 0x0000000080010033, CR2: 0xffffff801b98ed88, CR3: 0x0000000007d01000, CR4: 0x00000000001606e0
RAX: 0x0000000000000000, RBX: 0x0000000000000000, RCX: 0x0000000009000000, RDX: 0xffffff80171cf7c0
RSP: 0xffffff80f61db2c0, RBP: 0xffffff80f61db2f0, RSI: 0xffffff80f61db398, RDI: 0xffffff80171cf7b0
R8: 0x0000000000000000, R9: 0x0000000000000132, R10: 0xffffff80f61dbe90, R11: 0x000000000feaa000
R12: 0xffffff801b98ed80, R13: 0xffffff80171cf7b0, R14: 0xffffff80f61db398, R15: 0xffffff80060e0ad0
RFL: 0x0000000000010282, RIP: 0xffffff8005a43ca1, CS: 0x0000000000000008, SS: 0x0000000000000000
Fault CR2: 0xffffff801b98ed88, Error code: 0x0000000000000000, Fault CPU: 0x2
Backtrace (CPU 2), Frame : Return Address
0xffffff80f61daf60 : 0xffffff8005a1d626
0xffffff80f61dafd0 : 0xffffff8005ab7e75
0xffffff80f61db1a0 : 0xffffff8005acd3bd
0xffffff80f61db1c0 : 0xffffff8005a43ca1
0xffffff80f61db2f0 : 0xffffff8005a435d2
0xffffff80f61db3d0 : 0xffffff8005a245ed
0xffffff80f61db400 : 0xffffff8005def11a
0xffffff80f61db420 : 0xffffff8005def2d2
0xffffff80f61db450 : 0xffffff8005e50530
0xffffff80f61db470 : 0xffffff8005e501d1
0xffffff80f61db500 : 0xffffff8005e4fd3c
0xffffff80f61db560 : 0xffffff7f860161be
0xffffff80f61db600 : 0xffffff8005b1f855
0xffffff80f61db660 : 0xffffff8005adabe1
0xffffff80f61db750 : 0xffffff8005b1292e
0xffffff80f61db780 : 0xffffff8005ae16cf
0xffffff80f61db8c0 : 0xffffff8005ae0d6a
0xffffff80f61db920 : 0xffffff8005ae0c05
0xffffff80f61db950 : 0xffffff8005cfe410
0xffffff80f61db9f0 : 0xffffff8005b12549
0xffffff80f61dba50 : 0xffffff8005dbe4ec
0xffffff80f61dbad0 : 0xffffff8005a0508b
0xffffff80f61dbef0 : 0xffffff8005a06b9f
0xffffff80f61dbf60 : 0xffffff8005a85b38
0xffffff80f61dbfb0 : 0xffffff8005ab2957
Kernel Extensions in backtrace:
com.apple.iokit.IOStorageFamily(1.8)[A3CC4E44-8E10-3D9A-BA8E-95743E79D125]@0xff ffff7f8600a000->0xffffff7f8602efff
BSD process name corresponding to current thread: kernel_task
Mac OS version:
12C3006
Kernel version:
Darwin Kernel Version 12.2.1: Thu Oct 18 16:32:48 PDT 2012; root:xnu-2050.20.9~2/RELEASE_X86_64
Kernel UUID: 0AFA55FD-872F-3BBE-8630-214EB586A16D
Kernel slide: 0x0000000005800000
Kernel text base: 0xffffff8005a00000
System model name: MacBookAir5,2 (Mac-2E6FAB96566FE58C)
System uptime in nanoseconds: 33825093742539
last loaded kext at 30812273362661: com.trusteer.driver.gakl_driver_2 1 (addr 0xffffff7f8766b000, size 28672)
last unloaded kext at 15361113093292: com.apple.driver.AppleUSBCDC 4.1.22 (addr 0xffffff7f8765d000, size 12288)
loaded kexts:
com.trusteer.driver.gakl_driver_2 1
net.telestream.driver.TelestreamAudio 1.1.0
com.apple.filesystems.smbfs 1.8
com.apple.filesystems.autofs 3.0
com.apple.iokit.IOBluetoothSerialManager 4.1.2f9
com.apple.driver.X86PlatformShim 1.0.0
com.apple.driver.AGPM 100.12.81
com.apple.driver.ApplePlatformEnabler 2.0.6d1
com.apple.driver.AppleMikeyHIDDriver 122
com.apple.driver.AppleHDA 2.3.5fc10
com.apple.driver.AppleSMCPDRC 1.0.0
com.apple.driver.AppleLPC 1.6.0
com.apple.iokit.BroadcomBluetoothHCIControllerUSBTransport 4.1.2f9
com.apple.driver.AudioAUUC 1.60
com.apple.driver.AppleMikeyDriver 2.3.5fc10
com.apple.iokit.IOUserEthernet 1.0.0d1
com.apple.Dont_Steal_Mac_OS_X 7.0.0
com.apple.driver.ApplePolicyControl 3.2.13
com.apple.driver.AppleSMCLMU 2.0.3d0
com.apple.driver.AppleUpstreamUserClient 3.5.10
com.apple.driver.AppleBacklight 170.2.5
com.apple.driver.AppleMCCSControl 1.1.11
com.apple.driver.AppleIntelHD4000Graphics 8.0.6
com.apple.driver.AppleIntelFramebufferCapri 8.0.6
com.apple.driver.AppleUSBTCButtons 237.1
com.apple.driver.AppleUSBCardReader 3.1.7
com.apple.driver.AppleUSBTCKeyboard 237.1
com.apple.AppleFSCompression.AppleFSCompressionTypeDataless 1.0.0d1
com.apple.AppleFSCompression.AppleFSCompressionTypeZlib 1.0.0d1
com.apple.BootCache 34
com.apple.driver.XsanFilter 404
com.apple.iokit.IOAHCIBlockStorage 2.3.1
com.apple.driver.AppleUSBHub 5.5.0
com.apple.driver.AirPort.Brcm4331 612.20.14
com.apple.driver.AppleUSBXHCI 1.5.1
com.apple.driver.AppleAHCIPort 2.5.1
com.apple.driver.AppleUSBEHCI 5.5.0
com.apple.driver.AppleEFINVRAM 1.7
com.apple.driver.AppleSmartBatteryManager 161.0.0
com.apple.driver.AppleRTC 1.5
com.apple.driver.AppleACPIButtons 1.7
com.apple.driver.AppleHPET 1.8
com.apple.driver.AppleSMBIOS 1.9
com.apple.driver.AppleACPIEC 1.7
com.apple.driver.AppleAPIC 1.6
com.apple.driver.AppleIntelCPUPowerManagementClient 196.0.0
com.apple.nke.applicationfirewall 4.0.39
com.apple.security.quarantine 2
com.apple.driver.AppleIntelCPUPowerManagement 196.0.0
com.apple.kext.triggers 1.0
com.apple.iokit.IOSerialFamily 10.0.6
com.apple.driver.DspFuncLib 2.3.5fc10
com.apple.driver.X86PlatformPlugin 1.0.0
com.apple.driver.IOPlatformPluginFamily 5.3.0d47
com.apple.iokit.AppleBluetoothHCIControllerUSBTransport 4.1.2f9
com.apple.iokit.IOAudioFamily 1.8.9fc11
com.apple.kext.OSvKernDSPLib 1.6
com.apple.iokit.IOSurface 86.0.3
com.apple.iokit.IOBluetoothFamily 4.1.2f9
com.apple.driver.AppleGraphicsControl 3.2.13
com.apple.driver.AppleSMC 3.1.4d2
com.apple.driver.AppleHDAController 2.3.5fc10
com.apple.iokit.IOHDAFamily 2.3.5fc10
com.apple.driver.AppleSMBusPCI 1.0.11d0
com.apple.driver.AppleBacklightExpert 1.0.4
com.apple.driver.AppleSMBusController 1.0.11d0
com.apple.iokit.IONDRVSupport 2.3.6
com.apple.iokit.IOGraphicsFamily 2.3.6
com.apple.iokit.IOSCSIBlockCommandsDevice 3.5.5
com.apple.iokit.IOUSBMassStorageClass 3.5.1
com.apple.iokit.IOSCSIArchitectureModelFamily 3.5.5
com.apple.driver.AppleUSBMultitouch 237.3
com.apple.iokit.IOUSBHIDDriver 5.2.5
com.apple.driver.AppleThunderboltDPInAdapter 1.8.9
com.apple.driver.AppleThunderboltDPAdapterFamily 1.8.9
com.apple.driver.AppleThunderboltPCIDownAdapter 1.2.6
com.apple.driver.AppleUSBMergeNub 5.5.0
com.apple.driver.AppleUSBComposite 5.2.5
com.apple.driver.AppleThunderboltNHI 1.6.3
com.apple.iokit.IOThunderboltFamily 2.1.8
com.apple.iokit.IOUSBUserClient 5.5.0
com.apple.iokit.IO80211Family 510.4
com.apple.iokit.IONetworkingFamily 3.0
com.apple.iokit.IOAHCIFamily 2.3.1
com.apple.iokit.IOUSBFamily 5.5.0
com.apple.driver.AppleEFIRuntime 1.7
com.apple.iokit.IOHIDFamily 1.8.1
com.apple.iokit.IOSMBusFamily 1.1
com.apple.security.sandbox 220
com.apple.kext.AppleMatch 1.0.0d1
com.apple.security.TMSafetyNet 7
com.apple.driver.DiskImages 344
com.apple.iokit.IOStorageFamily 1.8
com.apple.driver.AppleKeyStore 28.21
com.apple.driver.AppleACPIPlatform 1.7
com.apple.iokit.IOPCIFamily 2.7.3
com.apple.iokit.IOACPIFamily 1.4
com.apple.kec.corecrypto 1.0Any or all of the following third-party system modifications may be contributing to your problem:
Rapport
Telestream audio driver
If the panic is recurrent, I suggest you uninstall them, one at a time, according to the developers' instructions, to see whether you can identify which one is at fault. A conflict between modifications may be involved. Reboot and test after each uninstallation.
Uninstalling Rapport
Back up all data before making any changes. -
How do I know If my computer has been hacked?
I think my Mac just got hacked into. I was working on a doc. that had personnel information- names. Phone #s and my home street address. my mac book pro froze up and when it unfroze, all of the names, phone#s and my address changed to ?/-\|# After I stared at the screen w disbelief for less than 1 sec. Word closed it down. After 2 min. Word brought the 2 word doc. I was working on back onto the screen. I looked at the personnel info, and saw the names, phone numbers and my street address in numbers and words. It looked like as if nobody touched my Mac. What should I do? I need help badly. If my computer has been hacked, the information they took, can they steal identity, credit card #s with just phone #s and first&last names besides my street address. I havent touched my computer since thus happened. I'm my iPhone. Should I turn off my computer? Also ididnt save the doc. I was working on. a box came up and said "this file is read-only. To save a copy, click OK and give the document a new namein the Save dialog box( AutoRecovery save of document1)". What should I do? I'm not making this up. I watched everything without realizing what happened. Should I have turned my computer off while it was in the middle of the proscess? Help! Help!
You have not been hacked. Something went wrong with Word and it crashed, and something must have reopened Word. (The system will usually ask if you want to reopen a crashed app... did you see such a message?) Word must have simply reopened the docs you had open when it crashed.
It's actually quite difficult to hack a Mac, and pretty much requires you to help out by opening it up for potential access by hackers. -
Is there a way for LabVIEW to know if the computer has an ethernet connection active?
I need to know in my VI if the computer has a network connection, to avoid trying to connect through TCP/IP when the connection is not available. I would prefer to know if there is a connection available rather than rely on errors coming from the TCP/IP functions not being able to connect.
Windows instantly knows when a network cable is unplugged. Is there a function in LabVIEW that can similarly instantly detect a connection?
Or, does anybody know if there is a Windows-provided dll that contains the function that the taskbar indicator uses to know if there is a connection present. If there is, then I could call the dll from LabVIEW and know the connection status.
Thanks.
AlejandroHi there,
there`s an API
unsigned long WNetAddConnectionA(CStr lpRemoteName, CStr lpPassword, CStr lpLocalName);
in mpr.dll.
lpRemoteName the address of a network resource (e.g. "\\YOURSERVER\YOURDRIVE")
lpPassword may be NULL
lpLocalName should be NULL, otherwise the API maps lpRemoteName to the drive you specify in lpLocalName (e.g. lpLocalName = "e:")
if all is ok, the API returns 0, otherwise some errorcodes.
more info can be found here
http://msdn.microsoft.com/library/default.asp?url=/library/en-us/wnet/wnet/wnetaddconnection.asp
best regards
chris
Best regards
chris
CL(A)Dly bending G-Force with LabVIEW
famous last words: "oh my god, it is full of stars!" -
my computer has some serious problems, my iphoto only shows only shows thumb size pics when I try to open them, i tried to rebuild my files from folders that had the pics in them. originally all the photos had a large delta with a question mark. also I can't back up the library file because its not there. I went to time machune and tried to find the file but I can't find it or I am looking in the wrong place. I also lost my Idvd file, only have broken chain showing.
Details please
What version of iPhoto and of the OS?
i tried to rebuild my files from folders that had the pics in them.
Exactly what did you do and how did you do it? this ay be the cause of your issue but without details we can n=ony guess
my iphoto only shows only shows thumb size pics when I try to open them,
where do you see htis? In the iPhoto window? what does "try to pen them" exactly mean?
originally all the photos had a large delta with a question mark.
Ok - this usually has a simple solution - do you still have a copy of the library that has this problem?
also I can't back up the library file because its not there.
This makes no sense at all - all of your previous statements indicate that you do have an iPhoto library but have some problems with it
By default your iPHoto library is located in your Pictures folder and is named iPhtoo library - if tha tis not the case the you have moved or renamed it and only you know what you did until you tell us the details
I went to time machune and tried to find the file but I can't find it or I am looking in the wrong place.
Again unless you actually share what and how you are doing thing but continue to simply state abstract problems it is no possible to assist you - details on using Time Machine are here -- http://support.apple.com/kb/HT1427?viewlocale=en_US&locale=en_US -- and -- http://pondini.org/TM/FAQ.html ---
I also lost my Idvd file, only have broken chain showing.
This would be better addressed in the iDVD forum - but again unlesss yu share detailed information no one can assist
LN -
How do I know if my computer has been hacked into?
I am having two issues with my iMac. One is with my wireless -- in the past few days I've received a few times an IP address error, which seems to be solved by renewing the DHCP lease and restarting. Also, at the login screen when I restart, it takes two tries to log in -- on the first one, my password only partially registers and the screen "bounces", then the second try works. Could this mean that my computer has been compromised? We had some workmen alone in our flat while we were away recently, so there are a few people who've had access to the physical machine as well. Thanks for any help.
You have not been hacked. Something went wrong with Word and it crashed, and something must have reopened Word. (The system will usually ask if you want to reopen a crashed app... did you see such a message?) Word must have simply reopened the docs you had open when it crashed.
It's actually quite difficult to hack a Mac, and pretty much requires you to help out by opening it up for potential access by hackers. -
The computer has rebooted from a bugcheck. The bugcheck was: 0x000000d1
The computer has rebooted from a bugcheck. The bugcheck was: 0x000000d1 (0x0000000000000000, 0x0000000000000002, 0x0000000000000000, 0xfffff80003cf33f7). A dump was saved in: C:\Windows\MEMORY.DMP. Report Id: 041715-27750-01.
https://drive.google.com/file/d/0BzDs1bdKVqlAcU9CZ3BMY2M3Wnk5eVV0WkhFWG9kYmRsaEtz/view?usp=sharingMH
This was related to the NETwbw02.sys Intel® Wireless WiFi Link Driver from Intel Corporation. I would remove the current driver and install the newest driver available
If you continue to crash I would remove Kaspersky and use the built in defender.
Microsoft (R) Windows Debugger Version 6.3.9600.17298 AMD64
Copyright (c) Microsoft Corporation. All rights reserved.
Loading Dump File [C:\Users\zigza\Desktop\041715-27750-01.dmp]
Mini Kernel Dump File: Only registers and stack trace are available
************* Symbol Path validation summary **************
Response Time (ms) Location
Deferred SRV*D:\Symbols*http://msdl.microsoft.com/download/symbols
Symbol search path is: SRV*D:\Symbols*http://msdl.microsoft.com/download/symbols
Executable search path is:
Windows 8 Kernel Version 9600 MP (8 procs) Free x64
Product: WinNt, suite: TerminalServer SingleUserTS
Built by: 9600.16384.amd64fre.winblue_rtm.130821-1623
Machine Name:
Kernel base = 0xfffff800`b7871000 PsLoadedModuleList = 0xfffff800`b7b389b0
Debug session time: Fri Apr 17 16:30:22.174 2015 (UTC - 4:00)
System Uptime: 0 days 0:00:10.822
Loading Kernel Symbols
Loading User Symbols
Loading unloaded module list
* Bugcheck Analysis *
Use !analyze -v to get detailed debugging information.
BugCheck D1, {0, 2, 0, fffff80003cf33f7}
*** WARNING: Unable to verify timestamp for NETwbw02.sys
*** ERROR: Module load completed but symbols could not be loaded for NETwbw02.sys
Probably caused by : NETwbw02.sys ( NETwbw02+993f7 )
Followup: MachineOwner
0: kd> !analyze -v
* Bugcheck Analysis *
DRIVER_IRQL_NOT_LESS_OR_EQUAL (d1)
An attempt was made to access a pageable (or completely invalid) address at an
interrupt request level (IRQL) that is too high. This is usually
caused by drivers using improper addresses.
If kernel debugger is available get stack backtrace.
Arguments:
Arg1: 0000000000000000, memory referenced
Arg2: 0000000000000002, IRQL
Arg3: 0000000000000000, value 0 = read operation, 1 = write operation
Arg4: fffff80003cf33f7, address which referenced memory
Debugging Details:
READ_ADDRESS: GetPointerFromAddress: unable to read from fffff800b7bc1150
GetUlongFromAddress: unable to read from fffff800b7bc1208
0000000000000000 Nonpaged pool
CURRENT_IRQL: 2
FAULTING_IP:
NETwbw02+993f7
fffff800`03cf33f7 488b09 mov rcx,qword ptr [rcx]
CUSTOMER_CRASH_COUNT: 1
DEFAULT_BUCKET_ID: WIN8_DRIVER_FAULT
BUGCHECK_STR: AV
PROCESS_NAME: System
ANALYSIS_VERSION: 6.3.9600.17298 (debuggers(dbg).141024-1500) amd64fre
DPC_STACK_BASE: FFFFF800B9C46FB0
TRAP_FRAME: fffff800b9c3f6b0 -- (.trap 0xfffff800b9c3f6b0)
NOTE: The trap frame does not contain all registers.
Some register values may be zeroed or incorrect.
rax=ffffe00004f2ed70 rbx=0000000000000000 rcx=0000000000000000
rdx=0000000000000000 rsi=0000000000000000 rdi=0000000000000000
rip=fffff80003cf33f7 rsp=fffff800b9c3f840 rbp=ffffe00004fd9890
r8=fffff800b9c3f890 r9=0000000000000000 r10=fffff800b7b62180
r11=fffff800b9c3f870 r12=0000000000000000 r13=0000000000000000
r14=0000000000000000 r15=0000000000000000
iopl=0 nv up ei pl zr na po nc
NETwbw02+0x993f7:
fffff800`03cf33f7 488b09 mov rcx,qword ptr [rcx] ds:00000000`00000000=????????????????
Resetting default scope
LAST_CONTROL_TRANSFER: from fffff800b79ccbe9 to fffff800b79c10a0
STACK_TEXT:
fffff800`b9c3f568 fffff800`b79ccbe9 : 00000000`0000000a 00000000`00000000 00000000`00000002 00000000`00000000 : nt!KeBugCheckEx
fffff800`b9c3f570 fffff800`b79cb43a : 00000000`00000000 00000000`00000000 ffff4ce4`1dc3da00 fffff800`b9c3f6b0 : nt!KiBugCheckDispatch+0x69
fffff800`b9c3f6b0 fffff800`03cf33f7 : 00000000`00000285 00000000`00000000 00000000`00000000 ffffe000`05be4ca0 : nt!KiPageFault+0x23a
fffff800`b9c3f840 00000000`00000285 : 00000000`00000000 00000000`00000000 ffffe000`05be4ca0 fffff800`03e62df0 : NETwbw02+0x993f7
fffff800`b9c3f848 00000000`00000000 : 00000000`00000000 ffffe000`05be4ca0 fffff800`03e62df0 ffffe000`04fd9540 : 0x285
STACK_COMMAND: kb
FOLLOWUP_IP:
NETwbw02+993f7
fffff800`03cf33f7 488b09 mov rcx,qword ptr [rcx]
SYMBOL_STACK_INDEX: 3
SYMBOL_NAME: NETwbw02+993f7
FOLLOWUP_NAME: MachineOwner
MODULE_NAME: NETwbw02
IMAGE_NAME: NETwbw02.sys
DEBUG_FLR_IMAGE_TIMESTAMP: 52a09c3a
FAILURE_BUCKET_ID: AV_NETwbw02+993f7
BUCKET_ID: AV_NETwbw02+993f7
ANALYSIS_SOURCE: KM
FAILURE_ID_HASH_STRING: km:av_netwbw02+993f7
FAILURE_ID_HASH: {1e0ec353-2360-690e-9374-7a77832276f2}
Followup: MachineOwner
Wanikiya and Dyami--Team Zigzag -
Computer has rebooted from a bugcheck windows 8.1
The computer has rebooted from a bugcheck. The bugcheck was: 0x00000124 (0x0000000000000000, 0xffffe001ad9b05d8, 0x0000000000000000, 0x0000000000000000). A dump was saved in: C:\Windows\Minidump\021715-15656-01.dmp. Report Id: 021715-15656-01.
My computer is rebooting and that's the error I'm getting in the event viewer. A link to the dump can be found below. Please help and thank you.Patrick
Better and no worries it happens
These are called BCC124 and are related to hardware. Read how to diagnose and hopefully to fix them read this
wiki
Since they refer to "authentic AMD" I would start by running a CPU stress test
Microsoft (R) Windows Debugger Version 6.3.9600.17298 AMD64
Copyright (c) Microsoft Corporation. All rights reserved.
Loading Dump File [C:\Users\Ken\Desktop\021715-15656-01.dmp]
Mini Kernel Dump File: Only registers and stack trace are available
WARNING: Whitespace at start of path element
WARNING: Whitespace at end of path element
Error: Empty Path.
Symbol search path is:
SRV*e:\symbols*http://msdl.microsoft.com/download/symbols
Executable search path is:
Windows 8 Kernel Version 9600 MP (6 procs) Free x64
Product: WinNt, suite: TerminalServer SingleUserTS Personal
Built by: 9600.17328.amd64fre.winblue_r3.140827-1500
Machine Name:
Kernel base = 0xfffff802`cca1a000 PsLoadedModuleList = 0xfffff802`cccf0370
Debug session time: Tue Feb 17 08:37:15.708 2015 (UTC - 5:00)
System Uptime: 0 days 0:00:06.408
Loading Kernel Symbols
Press ctrl-c (cdb, kd, ntsd) or ctrl-break (windbg) to abort symbol loads that take too long.
Run !sym noisy before .reload to track down problems loading symbols.
Loading User Symbols
Mini Kernel Dump does not contain unloaded driver list
* Bugcheck Analysis *
Use !analyze -v to get detailed debugging information.
BugCheck 124, {0, ffffe001ad9b05d8, 0, 0}
Probably caused by : AuthenticAMD
Followup: MachineOwner
0: kd> !analyze -v
* Bugcheck Analysis *
WHEA_UNCORRECTABLE_ERROR (124)
A fatal hardware error has occurred. Parameter 1 identifies the type of error
source that reported the error. Parameter 2 holds the address of the
WHEA_ERROR_RECORD structure that describes the error conditon.
Arguments:
Arg1: 0000000000000000, Machine Check Exception
Arg2: ffffe001ad9b05d8, Address of the WHEA_ERROR_RECORD structure.
Arg3: 0000000000000000, High order 32-bits of the MCi_STATUS value.
Arg4: 0000000000000000, Low order 32-bits of the MCi_STATUS value.
Debugging Details:
BUGCHECK_STR: 0x124_AuthenticAMD
CUSTOMER_CRASH_COUNT: 1
DEFAULT_BUCKET_ID: WIN8_DRIVER_FAULT
PROCESS_NAME: System
CURRENT_IRQL: 0
ANALYSIS_VERSION: 6.3.9600.17298 (debuggers(dbg).141024-1500) amd64fre
STACK_TEXT:
ffffd000`e116f500 fffff802`ccd9ffd0 : ffffd000`e5950180 ffffe001`ad9b05b0 fffff802`cccff800 fffff802`cca9a339 : nt!WheapCreateLiveTriageDump+0x81
ffffd000`e116fa30 fffff802`ccbde454 : ffffe001`ad9b05b0 ffffd000`e116fb50 fffff802`cccff8e0 ffffe001`ab557880 : nt!WheapCreateTriageDumpFromPreviousSession+0x44
ffffd000`e116fa60 fffff802`ccbdf271 : fffff802`cccff8e0 ffffd000`e116fb50 fffff802`cccff8e0 ffffd000`e116fb50 : nt!WheapProcessWorkQueueItem+0x48
ffffd000`e116faa0 fffff802`cca895e3 : fffff802`ccf2ed20 fffff802`ccbdf24c ffffc001`7f38d280 ffffe001`ab557880 : nt!WheapWorkQueueWorkerRoutine+0x25
ffffd000`e116fad0 fffff802`ccb18e70 : 00000000`00000000 ffffe001`ab557880 ffffe001`ab557880 ffffe001`ab4ac040 : nt!ExpWorkerThread+0x293
ffffd000`e116fb80 fffff802`ccb6f7c6 : fffff802`ccd1a180 ffffe001`ab557880 fffff802`ccd73a00 00000000`00000000 : nt!PspSystemThreadStartup+0x58
ffffd000`e116fbe0 00000000`00000000 : ffffd000`e1170000 ffffd000`e1169000 00000000`00000000 00000000`00000000 : nt!KiStartSystemThread+0x16
STACK_COMMAND: kb
FOLLOWUP_NAME: MachineOwner
MODULE_NAME: AuthenticAMD
IMAGE_NAME: AuthenticAMD
DEBUG_FLR_IMAGE_TIMESTAMP: 0
IMAGE_VERSION:
FAILURE_BUCKET_ID: 0x124_AuthenticAMD_PROCESSOR_BUS_PRV
BUCKET_ID: 0x124_AuthenticAMD_PROCESSOR_BUS_PRV
ANALYSIS_SOURCE: KM
FAILURE_ID_HASH_STRING: km:0x124_authenticamd_processor_bus_prv
FAILURE_ID_HASH: {6fd7875b-9a1b-9e09-d6d6-816026a875c8}
Followup: MachineOwner
Wanikiya and Dyami--Team Zigzag -
The computer has rebooted from a bugcheck, constant crash.
My newly built PC rebooted constantly and its driving me nuts, can anyone point me the reason? The errors are like this:
The computer has rebooted from a bugcheck. The bugcheck was: 0x0000001e (0xffffffffc0000005, 0xfffff8000db1f0c0, 0x0000000000000000, 0xffffffffffffffff). A dump was saved in: C:\Windows\MEMORY.DMP. Report Id: 112114-8000-01.
I ve uploaded the most recent .dmp files here
http://1drv.ms/1xWeDon
if it helps. Will gladly upload anything you request, I just want to know if its my faulty hardware or software issue. If this is the wrong section, please move it where appropriate.
Thank you.KP
These were Related to ndisrd.sys NDISRD helper driver from NT Kernel Resources. This may be a part of the OS or it may be malware. I would run a system file check and malwarebytes
Please run a system file check (SFC)
All instructions are in our Wiki article below...
Should you have any questions please ask us.
System file check (SFC) Scan and Repair System Files
Please download the free version of Malwarebytes.
Update it immediately.
Do a full system scan
Let us know the results at the end.
http://www.malwarebytes.org/products
Microsoft (R) Windows Debugger Version 6.3.9600.17237 AMD64
Copyright (c) Microsoft Corporation. All rights reserved.
Loading Dump File [C:\Users\Ken\Desktop\New folder\112214-29468-01.dmp]
Mini Kernel Dump File: Only registers and stack trace are available
************* Symbol Path validation summary **************
Response Time (ms) Location
Deferred srv*C:\Symbols*http://msdl.microsoft.com/download/symbols
Symbol search path is: srv*C:\Symbols*http://msdl.microsoft.com/download/symbols
Executable search path is:
Windows 8 Kernel Version 9600 MP (2 procs) Free x64
Product: WinNt, suite: TerminalServer SingleUserTS
Built by: 9600.17328.amd64fre.winblue_r3.140827-1500
Machine Name:
Kernel base = 0xfffff802`d307c000 PsLoadedModuleList = 0xfffff802`d3352370
Debug session time: Fri Nov 21 20:45:57.058 2014 (UTC - 5:00)
System Uptime: 0 days 0:00:15.828
Loading Kernel Symbols
Loading User Symbols
Loading unloaded module list
* Bugcheck Analysis *
Use !analyze -v to get detailed debugging information.
BugCheck C4, {40, 0, ffffcf80f31fcc10, 0}
*** WARNING: Unable to verify timestamp for ndisrd.sys
*** ERROR: Module load completed but symbols could not be loaded for ndisrd.sys
Probably caused by : ndisrd.sys ( ndisrd+2716 )
Followup: MachineOwner
0: kd> !analyze -v
* Bugcheck Analysis *
DRIVER_VERIFIER_DETECTED_VIOLATION (c4)
A device driver attempting to corrupt the system has been caught. This is
because the driver was specified in the registry as being suspect (by the
administrator) and the kernel has enabled substantial checking of this driver.
If the driver attempts to corrupt the system, bugchecks 0xC4, 0xC1 and 0xA will
be among the most commonly seen crashes.
Arguments:
Arg1: 0000000000000040, Acquiring a spinlock at IRQL < DISPATCH_LEVEL.
Arg2: 0000000000000000, Current IRQL
Arg3: ffffcf80f31fcc10, Spinlock address
Arg4: 0000000000000000
Debugging Details:
BUGCHECK_STR: 0xc4_40
CURRENT_IRQL: 0
CUSTOMER_CRASH_COUNT: 1
DEFAULT_BUCKET_ID: VERIFIER_ENABLED_VISTA_MINIDUMP
PROCESS_NAME: NetworkGenie.e
ANALYSIS_VERSION: 6.3.9600.17237 (debuggers(dbg).140716-0327) amd64fre
LAST_CONTROL_TRANSFER: from fffff802d36fe6b0 to fffff802d31cb1a0
STACK_TEXT:
ffffd000`20efd778 fffff802`d36fe6b0 : 00000000`000000c4 00000000`00000040 00000000`00000000 ffffcf80`f31fcc10 : nt!KeBugCheckEx
ffffd000`20efd780 fffff802`d37048e7 : fffff800`4cd921b0 ffffcf80`f3f24f70 ffffd000`20efd800 fffff802`00000000 : nt!VerifierBugCheckIfAppropriate+0x3c
ffffd000`20efd7c0 fffff800`4cd8e716 : ffffcf80`f31fcbc0 ffffd000`20efd868 00000000`00000000 fffff802`00000001 : nt!VerifierKeAcquireSpinLockAtDpcLevel+0x9b
ffffd000`20efd800 ffffcf80`f31fcbc0 : ffffd000`20efd868 00000000`00000000 fffff802`00000001 00000000`00000000 : ndisrd+0x2716
ffffd000`20efd808 ffffd000`20efd868 : 00000000`00000000 fffff802`00000001 00000000`00000000 fffff800`4cd8fb99 : 0xffffcf80`f31fcbc0
ffffd000`20efd810 00000000`00000000 : fffff802`00000001 00000000`00000000 fffff800`4cd8fb99 00000000`00010001 : 0xffffd000`20efd868
STACK_COMMAND: kb
FOLLOWUP_IP:
ndisrd+2716
fffff800`4cd8e716 ?? ???
SYMBOL_STACK_INDEX: 3
SYMBOL_NAME: ndisrd+2716
FOLLOWUP_NAME: MachineOwner
MODULE_NAME: ndisrd
IMAGE_NAME: ndisrd.sys
DEBUG_FLR_IMAGE_TIMESTAMP: 4e707f81
FAILURE_BUCKET_ID: 0xc4_40_VRF_ndisrd+2716
BUCKET_ID: 0xc4_40_VRF_ndisrd+2716
ANALYSIS_SOURCE: KM
FAILURE_ID_HASH_STRING: km:0xc4_40_vrf_ndisrd+2716
FAILURE_ID_HASH: {df7c0baf-f4d9-83e3-c876-e372e7f0e706}
Followup: MachineOwner
Wanikiya and Dyami--Team Zigzag -
"Your computer has restarted because of a problem."
Hello,
I've got a question, since two weeks my MacBook Air turns of and reboot it selfs.
It just happend again, and it was the 4th time thi week.
I get screenmessage:
"Your computer has restarted because of a problem. Press a key or wait a few seconds to contiune starting up."
But i didn't install things or what are there more people with this problem?
And what can I do to solve this problem.
Jasper.could you help me out???
Sun Sep 30 11:12:10 2012
panic(cpu 1 caller 0xffffff800f6b83c9): "Double fault at 0xffffff800fa23ce4, registers:\n" "CR0: 0x000000008001003b, CR2: 0xffffff8088807ff8, CR3: 0x0000000012257000, CR4: 0x0000000000000660\n" "RAX: 0xffffff800fc64c30, RBX: 0xffffff801b960180, RCX: 0x0000000000000001, RDX: 0x0000000000000001\n" "RSP: 0xffffff8088808000, RBP: 0xffffff8088808000, RSI: 0xffffff7f8fbaa4ec, RDI: 0xffffff801b8cef00\n" "R8: 0x0000000000000001, R9: 0x0000000000000000, R10: 0x0000000000000001, R11: 0xffffff800fa47c20\n" "R12: 0x00000000e00002c2, R13: 0xffffff801b7a7700, R14: 0xffffff7f8fbaa4ec, R15: 0xffffff801b8e6b00\n" "RFL: 0x0000000000010282, RIP: 0xffffff800fa23ce4, CS: 0x0000000000000008, SS: 0x0000000000000000\n" "Error code: 0x0000000000000000\n"@/SourceCache/xnu/xnu-2050.18.24/osfmk/i386/trap_native.c: 280
Backtrace (CPU 1), Frame : Return Address
0xffffff8082145ec0 : 0xffffff800f61d626
0xffffff8082145f30 : 0xffffff800f6b83c9
0xffffff80821460a0 : 0xffffff800f6ceddf
0xffffff8088808000 : 0xffffff800fa46062
0xffffff8088808020 : 0xffffff7f8fbbfdba
0xffffff8088808040 : 0xffffff800fa46816
0xffffff8088808060 : 0xffffff800fa47c5e
0xffffff80888080c0 : 0xffffff7f8fbb4a64
0xffffff8088808130 : 0xffffff7f9068301d
0xffffff8088808160 : 0xffffff7f90682d35
0xffffff8088808190 : 0xffffff7f8fba92fc
0xffffff8088808280 : 0xffffff7f8fc11c06
0xffffff8088808310 : 0xffffff7f8fba8e8e
0xffffff80888083a0 : 0xffffff7f8fbaa27e
0xffffff8088808480 : 0xffffff800fa47d9a
0xffffff80888084e0 : 0xffffff7f8fbaf7de
0xffffff80888085b0 : 0xffffff7f8fbd2bf0
0xffffff8088808630 : 0xffffff7f8fbb4e41
0xffffff80888086a0 : 0xffffff7f8fbb4dc7
0xffffff80888086f0 : 0xffffff7f906835f1
0xffffff8088808730 : 0xffffff7f9067d692
0xffffff8088808760 : 0xffffff7f8fba92fc
0xffffff8088808850 : 0xffffff7f8fc11c06
0xffffff80888088e0 : 0xffffff7f8fba8e8e
0xffffff8088808970 : 0xffffff7f8fbaa27e
0xffffff8088808a50 : 0xffffff800fa47d9a
0xffffff8088808ab0 : 0xffffff7f8fbaf7de
0xffffff8088808b80 : 0xffffff7f8fbd2bf0
0xffffff8088808c00 : 0xffffff7f8fbb4e41
0xffffff8088808c70 : 0xffffff7f8fbb4dc7
0xffffff8088808cc0 : 0xffffff7f906835f1
0xffffff8088808d00 : 0xffffff7f9067d692
0xffffff8088808d30 : 0xffffff7f8fba92fc
0xffffff8088808e20 : 0xffffff7f8fc11c06
0xffffff8088808eb0 : 0xffffff7f8fba8e8e
0xffffff8088808f40 : 0xffffff7f8fbaa27e
0xffffff8088809020 : 0xffffff800fa47d9a
0xffffff8088809080 : 0xffffff7f8fbaf7de
0xffffff8088809150 : 0xffffff7f8fbd2bf0
0xffffff80888091d0 : 0xffffff7f8fbb4e41
0xffffff8088809240 : 0xffffff7f8fbb4dc7
0xffffff8088809290 : 0xffffff7f906835f1
0xffffff80888092d0 : 0xffffff7f9067d692
0xffffff8088809300 : 0xffffff7f8fba92fc
0xffffff80888093f0 : 0xffffff7f8fc11c06
0xffffff8088809480 : 0xffffff7f8fba8e8e
0xffffff8088809510 : 0xffffff7f8fbaa27e
0xffffff80888095f0 : 0xffffff800fa47d9a
0xffffff8088809650 : 0xffffff7f8fbaf7de
0xffffff8088809720 : 0xffffff7f8fbd2bf0
0xffffff80888097a0 : 0xffffff7f8fbb4e41
0xffffff8088809810 : 0xffffff7f8fbb4dc7
0xffffff8088809860 : 0xffffff7f906835f1
0xffffff80888098a0 : 0xffffff7f9067d692
0xffffff80888098d0 : 0xffffff7f8fba92fc
0xffffff80888099c0 : 0xffffff7f8fc103fe
0xffffff8088809a50 : 0xffffff7f8fc11760
0xffffff8088809b30 : 0xffffff800fa47d9a
0xffffff8088809b90 : 0xffffff7f8fbb4a64
0xffffff8088809c00 : 0xffffff7f9068301d
0xffffff8088809c30 : 0xffffff7f90682d35
0xffffff8088809c60 : 0xffffff7f8fba92fc
0xffffff8088809d50 : 0xffffff7f8fc11c06
0xffffff8088809de0 : 0xffffff7f8fba8e8e
0xffffff8088809e70 : 0xffffff7f8fbaa27e
0xffffff8088809f50 : 0xffffff800fa47d9a
0xffffff8088809fb0 : 0xffffff7f8fbaf7de
0xffffff808880a080 : 0xffffff7f8fbd2bf0
0xffffff808880a100 : 0xffffff7f8fbb4e41
0xffffff808880a170 : 0xffffff7f8fbb4dc7
0xffffff808880a1c0 : 0xffffff7f906835f1
0xffffff808880a200 : 0xffffff7f9067d692
0xffffff808880a230 : 0xffffff7f8fba92fc
0xffffff808880a320 : 0xffffff7f8fc103fe
0xffffff808880a3b0 : 0xffffff7f8fc11760
0xffffff808880a490 : 0xffffff800fa47d9a
0xffffff808880a4f0 : 0xffffff7f8fbb4a64
0xffffff808880a560 : 0xffffff7f9068301d
0xffffff808880a590 : 0xffffff7f90682d35
0xffffff808880a5c0 : 0xffffff7f8fba92fc
Backtrace continues...
Kernel Extensions in backtrace:
com.apple.iokit.IOUSBFamily(5.4)[C3094550-7F58-3933-A4F7-CD33AE83F8B9]@0xffffff 7f8fba6000->0xffffff7f8fbfcfff
dependency: com.apple.iokit.IOPCIFamily(2.7.1)[9901C237-547C-3B52-99DE-C4870A19E2B5]@0xffff ff7f8fb7d000
com.apple.driver.AppleUSBHub(5.2.5)[A70C7553-FFEA-355F-A292-6E2B0023FADD]@0xfff fff7f9067c000->0xffffff7f90690fff
dependency: com.apple.iokit.IOUSBFamily(5.4.0)[C3094550-7F58-3933-A4F7-CD33AE83F8B9]@0xffff ff7f8fba6000
ng.uds.netusb.controller(1.0d1)[255630AE-2819-A974-1AC1-BB311E212189]@0xffffff7 f8fc08000->0xffffff7f8fc22fff
dependency: com.apple.iokit.IOUSBFamily(5.4.0)[C3094550-7F58-3933-A4F7-CD33AE83F8B9]@0xffff ff7f8fba6000
BSD process name corresponding to current thread: kernel_task
Mac OS version:
12C54
Kernel version:
Darwin Kernel Version 12.2.0: Sat Aug 25 00:48:52 PDT 2012; root:xnu-2050.18.24~1/RELEASE_X86_64
Kernel UUID: 69A5853F-375A-3EF4-9247-478FD0247333
Kernel slide: 0x000000000f400000
Kernel text base: 0xffffff800f600000
System model name: iMac10,1 (Mac-F2268CC8)
System uptime in nanoseconds: 1727840475139
last loaded kext at 57724112280: com.apple.driver.AppleBluetoothHIDKeyboard 165.5 (addr 0xffffff7f914e8000, size 24576)
last unloaded kext at 168222399221: com.apple.driver.AppleFileSystemDriver 3.0.1 (addr 0xffffff7f91707000, size 8192)
loaded kexts:
ng.uds.netusb.controller 1.0.0d1
com.apple.driver.AppleBluetoothMultitouch 75.15
com.apple.driver.AppleHWSensor 1.9.5d0
com.apple.driver.AudioAUUC 1.60
com.apple.iokit.IOBluetoothSerialManager 4.0.9f33
com.apple.driver.AGPM 100.12.69
com.apple.filesystems.autofs 3.0
com.apple.driver.AppleHDA 2.3.1f2
com.apple.driver.AppleMikeyHIDDriver 122
com.apple.iokit.IOUserEthernet 1.0.0d1
com.apple.Dont_Steal_Mac_OS_X 7.0.0
com.apple.driver.ApplePolicyControl 3.2.11
com.apple.driver.ACPI_SMC_PlatformPlugin 1.0.0
com.apple.driver.AppleMikeyDriver 2.3.1f2
com.apple.iokit.BroadcomBluetoothHCIControllerUSBTransport 4.0.9f33
com.apple.driver.AppleLPC 1.6.0
com.apple.driver.AppleBacklight 170.2.3
com.apple.driver.AppleUpstreamUserClient 3.5.10
com.apple.driver.AppleMCCSControl 1.0.33
com.apple.GeForce 8.0.0
com.apple.AppleFSCompression.AppleFSCompressionTypeDataless 1.0.0d1
com.apple.AppleFSCompression.AppleFSCompressionTypeZlib 1.0.0d1
com.apple.BootCache 34
com.apple.driver.AppleIRController 320.15
com.apple.driver.AppleUSBCardReader 3.1.0
com.apple.iokit.SCSITaskUserClient 3.5.1
com.apple.driver.XsanFilter 404
com.apple.iokit.IOAHCIBlockStorage 2.2.2
com.apple.driver.AppleAHCIPort 2.4.1
com.apple.nvenet 2.0.19
com.apple.driver.AppleUSBHub 5.2.5
com.apple.driver.AppleFWOHCI 4.9.6
com.apple.driver.AirPort.Atheros40 600.70.23
com.apple.driver.AppleUSBEHCI 5.4.0
com.apple.driver.AppleUSBOHCI 5.2.5
com.apple.driver.AppleEFINVRAM 1.6.1
com.apple.driver.AppleRTC 1.5
com.apple.driver.AppleHPET 1.7
com.apple.driver.AppleACPIButtons 1.6
com.apple.driver.AppleSMBIOS 1.9
com.apple.driver.AppleACPIEC 1.6
com.apple.driver.AppleAPIC 1.6
com.apple.driver.AppleIntelCPUPowerManagementClient 196.0.0
com.apple.nke.applicationfirewall 4.0.39
com.apple.security.quarantine 2
com.apple.driver.AppleIntelCPUPowerManagement 196.0.0
com.apple.driver.AppleBluetoothHIDKeyboard 165.5
com.apple.driver.AppleHIDKeyboard 165.5
com.apple.driver.IOBluetoothHIDDriver 4.0.9f33
com.apple.driver.AppleMultitouchDriver 235.28
com.apple.iokit.IOSerialFamily 10.0.6
com.apple.kext.triggers 1.0
com.apple.driver.DspFuncLib 2.3.1f2
com.apple.iokit.IOAudioFamily 1.8.9fc10
com.apple.kext.OSvKernDSPLib 1.6
com.apple.iokit.IOSurface 86.0.3
com.apple.iokit.IOBluetoothFamily 4.0.9f33
com.apple.driver.IOPlatformPluginLegacy 1.0.0
com.apple.driver.AppleSMC 3.1.4d2
com.apple.iokit.AppleBluetoothHCIControllerUSBTransport 4.0.9f33
com.apple.iokit.IOFireWireIP 2.2.5
com.apple.driver.AppleHDAController 2.3.1f2
com.apple.iokit.IOHDAFamily 2.3.1f2
com.apple.driver.AppleSMBusPCI 1.0.10d0
com.apple.driver.IOPlatformPluginFamily 5.2.0d16
com.apple.driver.AppleGraphicsControl 3.2.11
com.apple.driver.AppleBacklightExpert 1.0.4
com.apple.driver.AppleSMBusController 1.0.10d0
com.apple.nvidia.nv50hal 8.0.0
com.apple.NVDAResman 8.0.0
com.apple.iokit.IONDRVSupport 2.3.5
com.apple.iokit.IOGraphicsFamily 2.3.5
com.apple.iokit.IOUSBHIDDriver 5.2.5
com.apple.iokit.IOSCSIBlockCommandsDevice 3.5.1
com.apple.iokit.IOUSBMassStorageClass 3.5.0
com.apple.driver.AppleUSBMergeNub 5.2.5
com.apple.driver.AppleUSBComposite 5.2.5
com.apple.iokit.IOSCSIMultimediaCommandsDevice 3.5.1
com.apple.iokit.IOBDStorageFamily 1.7
com.apple.iokit.IODVDStorageFamily 1.7.1
com.apple.iokit.IOCDStorageFamily 1.7.1
com.apple.iokit.IOAHCISerialATAPI 2.5.0
com.apple.iokit.IOSCSIArchitectureModelFamily 3.5.1
com.apple.iokit.IOAHCIFamily 2.2.1
com.apple.iokit.IOUSBUserClient 5.2.5
com.apple.iokit.IOFireWireFamily 4.5.5
com.apple.iokit.IO80211Family 500.15
com.apple.iokit.IONetworkingFamily 3.0
com.apple.iokit.IOUSBFamily 5.4.0
com.apple.driver.NVSMU 2.2.9
com.apple.driver.AppleEFIRuntime 1.6.1
com.apple.iokit.IOHIDFamily 1.8.0
com.apple.iokit.IOSMBusFamily 1.1
com.apple.security.sandbox 220
com.apple.kext.AppleMatch 1.0.0d1
com.apple.security.TMSafetyNet 7
com.apple.driver.DiskImages 344
com.apple.iokit.IOStorageFamily 1.8
com.apple.driver.AppleKeyStore 28.21
com.apple.driver.AppleACPIPlatform 1.6
com.apple.iokit.IOPCIFamily 2.7.1
com.apple.iokit.IOACPIFamily 1.4
com.apple.kec.corecrypto 1.0 -
My daughter was updating her iphone to the iOS6 and everything went great. So, she was going to update mine. She used her itunes acct. instead of mine and it downloaded all her music and apps onto my iphone. Now when it asks for me to enter my password, it has her email address. How can I fix this???
plug your iphone into your computer with your itunes account signed in to update it, (if you want your own apps ect.) if all you want to do is change accounts signed in on the iphone than simply open settings and scroll down until you see itunes and app stores touch the apple id tip top and signout, sign yourself in. any apps she has "purschased" that you have not.. i imagine will just cease to work.
if you both share the same contacts, it won't be a big deal, however if you have work and her shcools numbers ect, and she just has mom/dad/buddies you may have double numbers and apps and what not by doing this, so if it does become a mess.. just get on itunes log into your account by clicking the store menu in itunes and going down to the account id on the bottom of that menu and just restore your phone.
Maybe you are looking for
-
I am trying to use Boston Acoustic BA7500G digital speakers with my SoundBlaster Audigy card. I can't get any sound out of them, but the device is working properly. Has anyone tried this combo before?
-
Hello Experts i created one report and try to load it but it give msg "load report failed" this is my code i used database as xml file and dataset as a table Try Dim oSubReport As CrystalDecisions.CrystalReports.Engine.SubreportObject
-
I just got PSE 10 and it will not open NEF, DNG or any RAW file it say the it is the wrong file type. Has anyone had a similiar problem?
-
Just downloaded iOS6 onto my iphone4 and now my playback repeatedly cuts out after a few seconds--a particular problem with podcast playback. Anyone else out there have this problem??
-
Coldfusion Scheduled Tasks Problem
Hello-- I am experiencing a strange problem. In a product that my office has created, we make use of Scheduled Tasks in Coldfusion. All of our clients are working just fine with the exception of one. There are several Tasks that all should behave the