Configure send connector for exchange online protection

Hello Forum members,
I am trying to configure send and receive connectors for Exchange 2010 to route
on-premises mailboxes to Exchange OnLine Protection.  The "help" info MS provides
is for Ex 2013 - and the EAC GUI and config does not lend a close fit to using the 2010
Exch Management Console.  How can I configure connectors to properly connect to the Exchange Online Protection?
I have seen where the ip addresses are posted, etc.  I am unclear how to configure the properties on the SBS 2011/EX 2010 server.
Any tips will help,
Thanks,
Eric H.
Network and Server Installs

Hello Wesleyhe,
You cannot use AD anything with EOP - if you mean exchange on-line protection.
you have to set a smart host on the SBS server to connect to EOP, you may need to add the EOP server ips to your network config
on the SBS server.  the smart host line (for the send connector on SBS server) is something like: yourdomainname-com.mail.protection.outlook.com.
Then you need to configure the outside ip for your SBS server access in the EOP admin area.
Hope this helps.
eholz
Network and Server Installs

Similar Messages

  • Send connector for forwarded emails not being used by Exchange 2013

    Hi we have 3 Exchange 2013 CU5 servers in a DAG setup and need to forward emails for some of the users to another domain. The problem is our outgoing spam filter seems to quarantine a lot of these emails which are  not spam. The problem is that I
    created a send connector for  the domain we are forwarding to (say contonso.com for illustrative purposes). Gave the send connector the name contonso.com, selected use MX record (didn't select Use the external DNS lookup settings on servers with transport
    roles) and added contonso.com in the address space gave it cost of 1. Added all the exchnage servers under source server. And clicked save. I then changed the cost to 2 on the main send connector with the domain as * which goes trhough our oput bound spam
    filter yet email I  send to one of the recipients with a forward inplace still go through that connector. Can anyone tell what i'm doing wrong or explain why this wouldn't work as expected ?   

    Easy question, did you enable the connector? :)
    Do you have more than one site in your org?
    DJ Grijalva | MCITP: EMA 2007/2010 SPA 2010 | www.persistentcerebro.com

  • Exchange Online Protection (EOP) instead of EDGE server ?

    Hi, we have Exchange 2010 with HUB server in LAN and EDGE in DMZ. There is an EDGE subscription on HUB and we use EDGE Sync.
    We have Forefront Protection 2010 for Exchange (FPE) installed on EDGE. Our license for FPE is coming to end and because FPE is discontinued we want to replace FPE by EOP as SPAM filter and AV for our on-premises Exchange 2010.
    What is the best practise in my scenario?
    Should I omit EDGE 2010 server and create send and receive connectors on HUB server for direct connection to EOP? Is EOP replaces the EDGE 2010?
    or
    Uninstall FPE on EDGE 2010 server and create on it send and receive connectors for direct connection to EOP?

    Hi,
    We can run the Windows Azure AD Sync Tool Configuration Wizard to set up directory synchronization. It would
    synchronize user accounts in an on-premises Active Directory environment to Windows Azure Active Directory (AD), where a copy of those accounts are stored in the cloud.
    Then we need to set up an Outbound connector and an Inbound connector to enable mail flow between Microsoft Exchange Online Protection (EOP) and your on-premises mail servers. Here are some references about
    directory synchronization and mail flow processing through Exchange Online Protection below:
    Best Practices for Configuring EOP
    http://technet.microsoft.com/en-us/library/jj723164(v=exchg.150).aspx
    Set Up Mail Flow Through Exchange Online Protection
    http://technet.microsoft.com/en-us/library/jj723133(v=exchg.150).aspx
    EOP Features
    http://technet.microsoft.com/en-us/library/dn305011(v=exchg.150).aspx
    Thanks,
    Winnie Liang
    TechNet Community Support

  • Configure POP3, IMAP and exchange online

    Configure POP3, IMAP and exchange online does not cause conflicts in outlook for my mail service

    Hello Wesleyhe,
    You cannot use AD anything with EOP - if you mean exchange on-line protection.
    you have to set a smart host on the SBS server to connect to EOP, you may need to add the EOP server ips to your network config
    on the SBS server.  the smart host line (for the send connector on SBS server) is something like: yourdomainname-com.mail.protection.outlook.com.
    Then you need to configure the outside ip for your SBS server access in the EOP admin area.
    Hope this helps.
    eholz
    Network and Server Installs

  • How to create send connectors for multiple sites in the same domain?

    Current Scenario:
    We have 2 offices, 1 in London and 1 in India. Both are in the same domain and are connected via VPN. Both have their own separate Exchange 2003 server. Each location sends out their mail via the Default SMTP Virtual Server on their exchange server through
    their local ISP. There are no Send connectors created currently.
    We have now installed an additional Exchange 2010 server with Hub, CAS and Mailbox roles at the London site. Internal mail flow between the sites seems to be working fine.
    I believe the Exchange 2010 needs a Send connector to send out mail to the internet. However as soon as we create a Send connector on Exchange 2010, mail from the older 2003 servers at both sites start to flow out from the exchange 2010 server. This is not
    optimal for our India site since their outgoing mail now has to flow via the VPN to London and out via the new server.
    How can we configure it so that each server sends outgoing mail independently?
    Thanks

    Hi,
    In India site, you can create a SMTP connector which point to the local ISP.
    Thanks.
    Niko Cheng
    TechNet Community Support

  • Can Exchange Online Protection work with Exchange 2010 on-premise

    I want to keep my current Exchange 2010 server but switch to Exchange Online Protection for anti-spam.
    Is that possible?
    Without doing any AD/Azure sync?

    Yes to both.  With directory synchronization you can have the added benefit of blocking mail to nonexistent recipients.
    Ed Crowley MVP "There are seldom good technological solutions to behavioral problems."

  • Forefront to Exchange Online Protection - Notification Issue

    So I guess we converted awhile back to EOP, but I wasn't with the organization.  The problem I have is, when I remove the sync tool off our server, I keep getting notifications that things arnt in sync etc.  Clearly they are because we are using
    the Azure tool now.
    I found our group email below in the old system (forefront admin center) but I can't edit it or remove it.  Any ideas on how to stop these emails!? Thank you!'

    So I guess since I started this thread I will respond to it to help everyone else out. I hadn't gotten a response in a week so decided to take matters into my own hands.
    We were migrated over to Exchange Online Protection like I'm assuming you others have.  What I ended up doing was logging into the EOP portal and going to service requests or support or whatever on the left hand side.  I put in a ticket to Microsoft. 
    They ended up escalating it to the FOPE team who then reached out to me via email and asked a few other questions to confirm what I was doing.
    They ended up taking care of it for me and we havn't gotten any notifications since.
    Hope this helps!! Let me know if you have further questions.

  • Exchange Online Protection and Public Folders

    Hi,
    We have just been migrated to Exchange Online Protection from FOPE and although users can now manage their own quarantines, they cannot do this for Mail Enabled Public Folders. Is this possible?
    Many Thanks

    Hi Paul,
    I replied to a post from you in another thread. It's easy to miss though, so here's what I said:
    "You should tell mail2web that there is an option in Exchange to hide public folders from IMAP clients. I'm an IT manager at a large software company with 50% of our users on Macs. We turned on the option to hide public folders from IMAP clients a while ago, long before the iPhone. It's worked very well and continues to work for iPhone people (like me!).
    There was no reason for us to make public folders viewable via IMAP, so hopefully the same will be true for mail2web."
    I'm actually really glad that Apple made this change. I want to see most of the folders at the inbox level in Exchange and with the Exchange switch turned on to hide public folders, there's no downside.
    Regards,
    fh

  • Exchange Online Protection

    Hello!
    I'm trying to configure hybrid deployment of Exchange 2010 and office 365 according to the article on MSExchange.org. I'm stuck with part three (http://www.msexchange.org/articles-tutorials/office-365/exchange-online/using-hybrid-configuration-wizard-exchange-2010-service-pack-2-part3.html).
    I don't know the IP address of the Exchange Onlinbe Protection server.
    I've bought exchange Online Plan1, so I suppose we can use Online Protection.
    Where can I found the particular IP addres of Exchange Online Protection Services?
    Thank you in advance,
    Moiseev Anton.

    I've found the answer: http://technet.microsoft.com/en-us/library/hh510075.aspx
    According to the information that I received from MS HelpDesk you can use any addres from those ranges. I personally didn't test it yet, because I stuck with the public certificate request.

  • Cannot load Exchange Online Protection commands in Remote PowerShell

    My colleagues and I cannot load the Exchange Online Protection commands in Remote PowerShell.
    It just loads the Exchange Online cmdlets.
    Where are we going wrong?
    PS C:\Users\jmorrison> $UserCredential = Get-Credential
    cmdlet Get-Credential at command pipeline position 1
    Supply values for the following parameters:
    PS C:\Users\jmorrison> $Session = New-PSSession -ConfigurationName Microsoft.Exchange -ConnectionUri https://ps.protection.outlook.com/powershell-liveid/
    -Credential $UserCredential -Authentication Basic -AllowRedirection
    WARNING: Your connection has been redirected to the following URI: "https://outlook.office
    365.com/powershell-liveid?PSVersion=4.0&realm={I've removed my domain name for security reasons}.co.uk "
    PS C:\Users\jmorrison> Import-PSSession $Session
    ModuleType Version   
    Name                               
    ExportedCommands              
    Script    
    1.0        tmp_4fnmyflw.she                   
    {Add-AvailabilityAddressSpac...
    PS C:\Users\jmorrison> Get-TransportRule
    Get-TransportRule : The term 'Get-TransportRule' is not recognized as the name of a
    cmdlet, function, script file, or operable program. Check the spelling of the name, or
    if a path was included, verify that the path is correct and try again.
    At line:1 char:1
    + Get-TransportRule
    + ~~~~~~~~~~~~~~~~~
    + CategoryInfo         
    : ObjectNotFound: (Get-TransportRule:String) [], CommandNotF
    oundException
    + FullyQualifiedErrorId : CommandNotFoundException

    I've moved MX records to EOP and seems to be fine all domain expect few.<o:p></o:p>
    I can see that problematic domain has "-" between domain names.<o:p></o:p>
    mydomain.com<o:p></o:p>
    mydomain-com.mail.protection.outlook.com --> has no problem, however<o:p></o:p>
    mydomain.usa.com<o:p></o:p>
    mydomain-usa-com.mail.protection.outlook.com having issue <o:p></o:p>
    when i checked in mx lookup it says MX record has NO A Record.<o:p></o:p>
    any suggestions<o:p></o:p>

  • MAPI/HTTP for exchange online?

    Hi Guys
    When Will Microsoft enable mapi/http for exchange online ?
    Hope this happens soon :)

    You might actually see this consuming more bandwidth.....
    And yes, the connect/reconnect/cold start is waaaay faster than RPC/HTTPS
    When it is enabled in o365, you will probably see it announced on the o365 Tech Blog.
    Cheers,
    Rhoderick
    Microsoft Senior Exchange PFE
    Blog:
    http://blogs.technet.com/rmilne 
    Twitter:   LinkedIn:
      Facebook:
      XING:
    Note: Posts are provided “AS IS” without warranty of any kind, either expressed or implied, including but not limited to the implied warranties of merchantability and/or fitness for a particular purpose.

  • Exchange Online Protection (standalone) permissions are not working as expected

    Exchange Online Protection (standalone)  permissions are not working as expected.
    we provided access to Hygiene Management to some members and they not able to access EOP site.
    This is standalone EOP.
    ksrugi

    Hi,
    what roles did you have assigned to them and what error message do you get?
    Greetings
    Christian
    Christian Groebner MVP Forefront

  • Outlook configuration for Exchange online kiosk plan

    Hi,
    I'm trying to configure outlook for kiosk user and only the mails in inbox is getting download. Mails in other folders are not getting download.
    Please help...

    Hi,
    We have to use POP3 to setup Outlook when you want configure Exchange Online Kiosk in Outlook 2007/2010, and Outlook 2013.
    Since this issue is related to Exchange Online, we recommend contact Office 365 team so that you can get more professional suggestion. For your reference:
    http://community.office365.com/en-us/default.aspx
    Thanks
    Please remember to mark the replies as answers if they help, and unmark the answers if they provide no help. If you have feedback for TechNet Support, contact [email protected]
    Allen Wang
    TechNet Community Support

  • Can't figure out how to use Amazon SES as a smart host for Exchange Online

    Hi,
    I have a problem that is proving very difficult to solve, and I'm hoping someone on here might know a bit more about this.
    I am trying to configure MS Exchange Online to route all emails through Amazon SES as a relay server, however the problem is that SES seems to want you to pass it SMTP username and password credentials to authenticate with, and I don't think Exchange Online
    allows for this?
    I have checked all the options in Outbound Connector section and there doesn't seem to be any place where I can choose SMTP authentication.  On Exchange 2013 and on-premise 365 Exchange solution I believe you can do this, but with pure Exchange Online
    I'm not sure...
    Does anyone know whether this is possible, and if not why Microsoft doesn't allow it / if they might be intending to enable this in the near future?
    Thanks a lot in advance!
    Tom

    Hi,
    Since your questions are Exchange Online related, I suggest we also ask it on the Microsoft Exchange Online forum:
    https://social.technet.microsoft.com/Forums/msonline/en-US/home?forum=onlineservicesexchange
    Hope you can get your answer soon.
    Thanks,
    Please remember to mark the replies as answers if they help and unmark them if they provide no help. If you have feedback for TechNet Subscriber Support, contact
    [email protected]
    Simon Wu
    TechNet Community Support

  • Bulk User creation Exchange Online Protection standalone

    Hi,
    We have on premise Exchange 2013 servers and we're planned to go for EOP only for SPAM filtering. I have couple of questions with EOP:
    When we create bulk user accounts from a CSV file do we need to Allow users to sign in to EOP?
    what will be the EOP address for On-Premise send connector(send emails from the organization)? and how to get it?
    is there any proper step by step guide to setup EOP standalone?
    Thanks..
    Roshan

    You don't need to allow sign in today, but in the
    future there will be a personal
    quarantine for users.
    set the value to the MX record given to you during EOP setup, such as <your organization>-com.mail.protection.outlook.com.
    (http://community.office365.com/en-us/wikis/exchange/4238.aspx)
    http://technet.microsoft.com/en-us/library/jj723153(v=exchg.150).aspx
    Mike Crowley | MVP
    My Blog --
    Planet Technologies

Maybe you are looking for

  • Vendor Return process in case of Import Goods (Excisable)

    Can anyone provide me the complete process details with configuration in case of Return of Import Goods to Vendor? The scenario is we have received the goods from an overseas Vendor by availing the benefit of CVD and we have made payment to the Vendo

  • How i can change date format in the query

    I have made a query and Document date format is DD/MM/YYYY but i want Document date Format as YYYYMMDD. Please help me out as soon as posible. Thanks is advance.

  • Adobe Fireworks slide show in iWeb

    I am trying to place a slideshow created in Adobe Fireworks in an iWeb page.  The slideshow is a .xml file.  Nothing is showing up.  I have watched a few tutorials...same result.  Does the HTML snippet work with this?

  • KDm exchange rate key

    Hi All, I have created a PO where I have changed the currency from EUR to USD at the header level and fixed a different exchange rate than existing in the system (system rate is 1.5 and I have fixed it at 1.25). Indicator "Exch. rate fixed" has been

  • Black screen problem

    Hello. I Have a hp laptop TouchSmart tx2-1105ei   I have a strange problem with my device, almost every 1 or 2 days when Im using it (whether in windows or even when I was in bios setup and befor system boot it occured), the display turns blank and d