Configuring the time capsule airport wlan function as "connect to wlan", the time caspule gets a correct IP adress from the other wlans IP range, but does not assign this to the ethernet ports. With Airport Express it worked!

Configuring the time capsule airport wlan function as "connect to wlan", the time capsule gets a correct IP adress from the other wlans IP range, but does not assign this to the ethernet ports. With Airport express it worked, the single Ethernet port got the IP Parameters passed through!
My setup is a Vodafon Esaybox connected to ISP. Time Capsule is not able to extend the wlan of the easybox, neither airport express can do.
Only the option "connect to wlan" is succesful.
With airport express I was able to connect my Sony Bravia TV to the lan via ethernet to stream pictures, the TV set got an IP adress from the easybox.
With the time capsule the easybox dosn't find devices connected to the ethernet ports to submit IP adresses. The TV set get another IP adress (169.xxx.x.x.) in subnet mask 255.255.0.0 and I don not now where from.
My notebook is a MacBook pro.
Any idea????
Thank a lot in advance!
Kind regards
Ingo

Neverthe less, could there be the chance, that this feature could be implemnented with an firmware update?
That would appear to be a question for Apple to answer. You can make suggestions to Apple here:
Apple - AirPort Extreme - Feedback
If the AirPort Extreme and Time Capsule are configured to "extend a wireless network" they will provide additional wireless coverage....and...the Ethernet ports are enabled in this type of setup.
The "catch" here is that you must have an Apple router providing the network to be extended.

Similar Messages

  • HT1386 My iOS device (Ipad mini) only appears in iTunes while cable-connected, but does not appear after diconnect the cable. How can I Wifi sync ?

    Hi, My iOS device (Ipad mini) only appears in iTunes while cable-connected, but does not appear after diconnect the cable. How can I Wifi sync ?
    Documents say
    Whenever the computer and the iOS device are on the same network, the iOS device will appear in iTunes, and you can sync it....
    But I can't see my iPad Mini in iTunes.
    And my  Ipad  (Settings, General, iTunes Wifi Sinc)  shows  a message :" Sync will resume when xxx(my PC with iTunes) is available "...
    Both are in the same network,
      Ipad mini is is plugged in to power
    . iTunes is open on the computer
    what can i Do ???

    Hi Skydiver119,  and tks for four interest.
    I have done exactly as you say, but it does not work for me.
    You indicated  " Navigate to the info tab and scroll down. There'll be a check box for 'sync over wifi' or something to that effect. Check that box and sync to affirm your choice."
    I navigated to Summary tab (not Info Tab) and checked "Sync with this ipad over Wi-Fi"
    I disconnect the wire,
    and my iPad disappears from my iTunes screen.
    in my iPad ->Settings -> General -> iTunes Wi-Fi Sync -> says " Sync will resume when (my PC) is available.
    So, I can not sync via wi-fi
    I appreciate if you can help me.

  • I created a theme and a slideshow in iDVD. The theme (intro) plays looped in the preview, but does not go on to the slideshow. How do I "un"loop it?

    I created a theme and a slideshow in iDVD. The theme (intro) plays looped in the preview, but does not go on to the slideshow. How do I "un"loop it?

    Perhaps someone on this forum has done what you are asking and would be more help than me. 
    I think it could be done, but you'd have to do some fiddling around. The concept is to make the iDVD theme part of your iDVD or iMovie created slideshow, so that it will play as part of the slideshow.
    I don't know if this will work, but if I were experimenting I would try creating an iDVD project with just the theme in it, and then save that to your desktop as a disc image.  When you click on the icon of the disc image you have just created, you will see a Video_TS folder.  Open that and you will see a file containing the letters VOB.  Open that file. 
    You need to convert that VOB file back to DV or Quicktime Movie which iMovie is designed to handle. For that you need  the free download MPEG Streamclip:
    http://www.apple.com/downloads/macosx/video/mpegstreamclip.html
    but you must also have the Apple mpeg2 plugin :
    http://www.apple.com/quicktime/mpeg2/, which I believe costs about $20.
    Open MPEG Streamclip and drag the VOB file to its window.  Go to the MPEG Streamclip file menu and click on Export to DV. 
    After the export is done, you will have a DV file containing the iDVD theme.  I would try adding that clip as your first entry in your slide show, assuming that you are running iDVD7.  (You can't add a movie to a slideshow in iDVD6.)  When you play your slideshow hopefully it will play the DV clip containing the theme, then seamlessly followed by your slide show.   If it doesn't, try instead exporting the VOB file to a Quicktime Movie, and then try to add the Quicktime movie to your slideshow.
    You might be able to do this easier if you created your slideshow in iMovie instead of iDVD.  You could make an iMovie with the iDVD theme clip as the lead clip, and then share your iMovie project to iDVD. 
    Good luck with this.  As I said, perhaps someone else has an easier way to do this and will chime in. 

  • When I touch buttons voice names them but does not really respond.  What should I do to restore normal work?

    When I touch buttons voice names them but does not really respond.  What should I do to restore normal work? Thank you

    I have the same problem, its an ipod touch, the most recent version, for my granma. she is blind. it wouldn't respond when you pick something, double tapping or even identifying it when either of use it.
    i can see that i am tapping the buttons in VO mode and it doesn't respond. It also says to scroll with three fingers and that takes 20 tries to get to work. I bought this for my grandmother to use VO and it doesn't work. Its a load of crap. I thought if I updated that might help, it doesn't need to be updated.
    And the voice speed is almost at the lowest and it still talks fast.
    It is ridiculous to have a feature like this and it not be useable. Disgruntled and disgusted by Apple's disregard for the people who could most benefit from this type of technology. I've looked on websites for the blind. So far, no help or advice.

  • I recently purchased a new mac computer and would like to sync the music off my iPhone to my new mac.However, my phone and my new mac have different apple Ids.The PC which my phone is synced and has the same apple ID but does not let me transfer the music

    Hi I recently purchased a new mac computer and would like to sync the music off my iPhone to my new mac.However, my phone and my new mac have different apple Ids.The PC which my phone is synced and has the same apple ID but does not let me transfer the music. Home sharing is not working. How do I successfully transfer and sync the music off my ipone 4 to my mac book pro if they have different Apple IDs? Thanks!

    What do you mean the PC won't let you transfer the music? Save your entire iTunes folder (this is assuming that you have all your music stored in your iTunes folder) to an external hard drive. Connect that hard drive to your Mac. Copy the iTunes folder to your computer. Hold down the option key while launching iTunes on your Mac. Select the library you just copied when it ask you to select which library you want to open.

  • Hey...... my ipod touch 2g wifi dose not work.... it connects to the network but does not open any of the web pages or internet acess!! HELP ME???

    Someone plz help me out with this problemm... My IPOD TOUCH 2G connects to the wifi network but could not open any of the web pages... i've tried SAFARI, FIREFOX, and OPERA.... nothing in wifi retrieves data!!! it makes me so angry...
    possible reasons???? i've searched net.. and many of the people r having these problems... maybe with the ne iOS4.2.1
    HELPPPPPPPPPPP????
    ...Fateh

    - Reset the iPod:
    Reset iPod touch:  Press and hold the On/Off Sleep/Wake button and the Home
    button at the same time for at least ten seconds, until the Apple logo appears.
    - Power off and then back on your router
    - Reset network settings: Settings>General>Reser>Reset Network Settings
    - The troubleshooting here:
    iPhone and iPod touch: Troubleshooting Wi-Fi networks and connections
    - Does the iPod successfully connect to other routers?

  • Add additional ethernet ports with airport express

    Is there a way to add an additional ethernet port to an airport express via a router or some other option? I have a need for two devices using ethernet next to the airport express.
    Thanks,
    Guy Gadois

    If you want the AX to connect wirelessly to a network and then connect Ethernet clients to the AX's Ethernet port, read Tesserax's post above. This requires WDS.
    If you want to connect the AX to an Internet source and also have Ethernet clients you want to connect to that Internet source, read my post above. This is not possible using only the AX. You need a router with 2 or more Ethernet ports unfortunatley the AX only has one.

  • HT1976 i bought an UNLOCKED 1phone 5 fom the Apple store in Millenia Mall, Orlando on Sunday, Flew back to Jamaica and had my SIM card from my 4 cut down and it does not work, The shop tried another SIM from a 5 and it still did not work HELP

    HELP!!

    help with what? you're providing no information.
    "it does not work" means nothing.  What specifically is the problem?

  • I just purchased Apple USB SuperDrive and connected to my Mac mini 2012 but does not show anything on the screen. Not sure if its working.

    I just purchased Apple USB SuperDrive and connected to my Mac mini late 2012 USB slot but nothing shows up on the screen.
    I have OS X versus 10.10.3

    The system bus and all connected products should appear in the system profile or in the
    hardware part of About this Mac (more info) and if that does not, restart the computer with
    the external Apple USB SuperDrive plugged in. •As a last resort, if nothing else, before a
    return trip to be rid of the SuperDrive, you could try a system management controller reset.
    The SMC reset is not a first choice, so I won't post a link to the support instruction page.
    A new Apple USB SuperDrive should be seen as hardware in system information report.
    Of course, an icon of disc media should appear once the disc is inserted into the drive, too.
    Good luck & happy computing!

  • How do you get the IPAD2 to charge? We have tried both ways and it never goes any higher than the percentage it is? We have plugged it into our computer and into an electrical outlet but does not charge. We got it brand new so it should work.

    We are having trouble getting our new IPAD2 to charge. We have hooked it up to our computer and no charge, we have used the outlet and still no charge. When we first connect it to an outlet it shows the battery but it immediately goes off and it is still at the same percentage hours later.
    Do you have any suggestions as to what we need to do to get it charged?
    thanks
    Connie

    Try resetting your iPad by pressing the home and sleep buttons until you see the Apple logo, ignoring the slider. Takes about 5-15 secs of button holding and you won't lose any data or settings.
    Then try to charge.
    It should charge from the outlet but may not from a USB.  Try a different cable or adapter.  If you don't have one, take it all in to Apple... the adapter may be defective.  You have a 1 year waranty.

  • Music is on my iPod touch 1G but does not show up in the Music App

    Been having this problem the last week. I synced my iPod before I went to bed, grabbed it and headed off to work on Tuesday. Once I got to work I went to use my iPod and when I opened the Music App a screen popped up saying "Updating Library...This may take a few minutes". I didn't think much about that as I have seen it a number of times after I synced quite a bit of new music or podcasts(the night before I had 3 new hour long podcasts that synced).
    Set my iPod to the side as that usually does take a minute, turned back and the screen said "No Content" and then some line about buying music in iTunes. I was quite surprised as I had never seen this screen before. I turned my iPod off and back on and the same No Content message.
    I checked my Photos App and those were still there and so were all my saved photos that don't sync. Checked some of my other apps and the settings and saved data was all there too.
    Finally got the idea to check the About option in the Settings. Knowing that it would list how many songs and how much space was free. Opened that up and it said 0 songs but that I only had 1.4GBs of free space. Which tells me that my music is on the iPod but just isn't being recognized.
    Got home that night and synced it and once done I checked it and my music was there. Friday this all happened again and I have not been able to get my music to show up again even though my iPod tells that I have 12GBs of something on there going by what the About page tells me.
    The only change I have made is I finally updated from just Itunes 10.0.X to 10.1.4 on 12/20 of last year. I have a iPod touch 1G that is running 3.1.3.
    Last night I did a restore and created a whole new iPod but the same issue has happened. I watched it sync my ~2800 songs but when I went to check them, No Content but the About page tells me there is 12GBs of space being used. Right now I am going to a back from from June of last year to see if that works but I doubt it. I also have an old install of iTunes 10.0.1 that I think I might try.
    What else could be the problem?

    Which version of iTunes are you using?
    Stedman

  • My guest account is enabled, but does not show up in the login window. I'd like it to, thanks!

    I've tried disabling then enabling it, but it does not appear.

    Have you tried a safeboot? It can fix allot of account issues. Like accounts vanishing from the login list.
    if that doesn't work, You change the login window to Name & Password, then you can try logging in with the account name "guest". dos it let you login?
    if that doesn't work, can you post the output of  "dscl . read /users/Guest" ?  (skip JPEGPhoto)

  • XPAR_PS7_DMA_NS_DEVICE_ID listed in xparameters.h with memory range but does not operate?

    Hello All,
    I have a zedboard.  Using vivado I built a zedboard preset project.  I then selected the xilinx example peripheral test project.  When I build and run it all works.  The confusion I am having, being used to working with SDK before (previously worked with virtex-5 FXT device), is that the xparameters.h file lists two processor system (PS) DMA peripherals XPAR_PS7_DMA_NS and XPAR_PS7_DMA_S.  The peripheral test uses the XPAR_PS7_DMA_S.  When I change the DMA test to use the _NS device the test fails.  It appears that all the device driver support code reports no errors, but the DMA just does not operate for the _NS device.  When I pull up the processor side block diagram in Vivado it only shows one DMA unit with 8 channels.
    I am very confused why xparameters shows the possibility for two DMA instances, but everywhere else, the documentation and tools only list one as usable.
    Is the _NS instance just not usable at all?  If so why does it appear with a memory mapping in xparameters.h?
    I would appreciate any help.  The reason I am hunting this so hard, is because I would like to dedicate one DMA instance per ARM core.  If there is only one DMA instance available, this will force me to ask the hardware designers to give me a different DMA peripheral to use - so there will not be conflicts between the cores and the peripheral.
    Any help is appreciated.
    Thank you.

    A FAE got back to me, and indicated that there is only one DMA unit with 8 channels.  The S instance is the secure instance of the DMA block.  The NS is the non-secure instance.  The secure versus non-secure operation has to do with ARM Trustzone technology.  By default only the secure DMA version interrupts are usable, to get non-secure interrupts, it takes more work.

  • When I upload audio from itunes into my imovie project, it does not show all of the track?

    Hi, I have opened a new project in imovie - I have uploaded 200 photos into the project to make a Comic Book movie!
    this project is 7 mins and 8 seconds long - the exact length of the audio track that I want to play during the movie!
    I have selected the music by clicking the musical note button in imovie, which open up my itunes library and displays the track I want to use that is 7 mins and 8 seconds long.
    When I click and drag my MP3 audio from itunes into my imovie project, i only plays the first 5 mins & 33 seconds; leaving my project in silence for the final 1 min & 3 seconds????
    I have not added markers, there are no fade ins or fade outs - only the first 5 min & 33 seconds or a 7 min & 8 seconds MP3 Audio track???
    I have spent 10 hours trying to rectify this problem.......
    can anyone help me with this problem
    Peace, Love & Happiness
    Jayondrums

    Sounds like your talking about iMovie for Mac?
    This is the iOS version, repost here:
                                                      iMovie

  • An mov file which play fine in quicktime on my mac mini will not play in quicktime on a windows 7 unit. Error 2048, quicktime does not understand this file. Any ideas as to why it works in mac version of quicktime and not windows version?

    The .mov file sis downloaded from my Sony camera. It is not altered and plays fine on the Mac mini using QuickTime. It will not play on a Windows 7 unit using the latest version of Quicktime. Why would that be? Why will one version of QuickTime work and another not work?

    Also make sure the file type is not of a DivX. That your camera supports. Which QT for Mac also supports, but the Windows version of QT does not support DivX, so you're not purchasing something for the Windows computer that is not needed?

Maybe you are looking for

  • Open in New Page

    Hi all, I'm using OBN between two DB Querys. anybody know, how can I do to call the target in a external Windows ? Regards.

  • Can you have two address books on one icloud account?

    My wife and I want separate contact lists.  Is there any way to do this with 1 ICloud account? Thanks,

  • TC takes longer to re-boot; reports a problem; then fixes itself?

    I had a lot of problems yesterday with my TC. I lost my internet connection and spent 4 hours working on resetting it and the cable modem so they would communicate. During that process, and still today, I am finding a slow internet connection. But, t

  • Cost center relationship with department

    Hi experts, I have one question to ask about cost center relationship.Let say one department use only one cost-center. Is it I have to key-in the relationship between department and cost-center only or I have to key -in all the position in that depar

  • Does IOS 7 support off-line dictation?

    There was scuttlebut around a while ago that IOS 7 might support off-line dictation, possibly only in the new iPhone 5S. Anyone know if this is true? If this feature is supported, is it only for the 5S and not the 5C?