Contact search function not found

I've definitely upgraded to iPhone 2.0. I am not finding the search function (I don't see a search field) when I access my contacts through the Phone icon, Contacts tab.
When I use the Contacts icon, I also don't see a search field. I tried tapping the top of the screen thinking that would make it appear but it doesn't. Mysterious, or am I missing something basic here?

Matcha,
Did you try using the scroll function on the right (all the letters) and go all the way up to the top? There's a little magnifying glass icon above the "a" and when you get up that high, you should see the search field pop into view at the top.
Hope this helps.
-Mark

Similar Messages

  • Search functionality not working in Purchase order

    Hi all,
    We are using extended classic scenerio's .But we are unable to search the Purchase orders against status "order ,awaiting approval etc"
    However, we are able to search only "Status Held" PO's
    Could you please tell me the soultion for this. Seems to be search functionality not properly activated.
    Thanks and regards
    Harish shetty

    Hi Harish,
    See if the following OSS notes are helpful:
    Note 1138911 - BBP_POC - Search issue in purchase order
    Note 1128758 - BBP_POC: Search Issue in Purchase Order
    Thanks,
    Pradeep

  • Function not found in Library only after Close VI - Open VI

    Hi,
    We wrote subVI's for all exported functions of a dll written in Borland C++. Then a test.vi was implemented which uses these dll function. Everything runs perfectly, as long as we don't Close the vi and reopen it from the LabView main menu. If we do this the broken run arrow butten is shown and the first error message listed is the Function not found in Library error.
    If we use Exit to leave LabView and then restart the test.vi, everything is ok.
    Please let me know if you know a solution. Thanks in advance.

    The Function not found error is thrown when the OS can't provide the pointer to the function in the library to LabVIEW for some reason. For more information and common solutions see:
    http://digital.ni.com/public.nsf/websearch/44E40ACF1644DB77862562990054D672?OpenDocument
    The only reason I can think of why the first time it works correctly is that the DLL is not correctly clean-up by the close functions. Thus causing a second request for the pointer to fail due to this. (closing LabVIEW will remove the DLL form memory and thus probably clearing the error).
    Hope this Helps
    Kind regards,
    Karsten
    Applications Engineer
    National Instruments

  • Call library function node - function not found

    When creating a DLL I get a the Labview error "Call Library Function Node "LabviewReceiverDLL.dll:readDataJ1939Data' Function not found. Everything looks correct to me and this used to work, though I've changed computers since then.
    This is the beginning of my C++ code just to show my function name. I've also attached the Call Library Function Window to show my setup.
    Thank you in advance for your help.
    #include"StdAfx.h"
    #include<iostream>
    /* Call Library source file */
    extern"C"__declspec(dllexport)unsignedint readDataJ1939Data(unsignedint, unsignedint, unsignedchar, unsignedchar* canData, unsignedchar* path);
    unsigned int readDataJ1939Data(unsignedint ulTimeStamp, unsignedint ulIdentifier, unsignedchar uiDataCount, unsigned char* canData, constchar* path)
    Solved!
    Go to Solution.
    Attachments:
    Call Library Function.png ‏192 KB

    You mention that you have changed computers and that it used to work before.
    Could it be that there is another (older) copy of the DLL on this computer, and LabVIEW is loading the wrong one?
    The simplest way to check is to close your VI and delete the one you are expecting it to use.  Then open the VI again; if LabVIEW doesn't ask you where the DLL is, it is loading it from somewhere else.
    Batya

  • Call library function node: function not found in library

    I'm using Labview 6.1 and Windows XP.  I am trying to open some code, but it opens up with a broken arrow.  The error is Call Library Function Node:function not found in library.  Tried to configure the node, but no change.  Moved the DLLs to various directories (keeping them together) but again no change. 
    This code has been compiled and is working fine.  I'm just trying to run the source code to make some modifications.  Any suggestions? 
    Thanks
    CarlosV

    Thanks for the suggestions.  Tried it but had the same results.  The library I'm using is hpe1413_32.dll. 
    One thing I forgot to mention....doing a configure on the node, it comes up with the library: hpvscp32.dll and the function: hpe1413_error_message
    The function doesn't exist in the library.  So I set the path to hpe1413_32.dll which does contain the function. 
    After closing the configuration window and opening it up again, the library shown is hpvscp32.dll
    From what I can tell, there are three libraries involved:hpe1413_32.dll, hpe141332v.dll, and hpvscp32.dll
    Thanks again.
    Carlos

  • Call Library Function - Function not found in library

    Hello,
    I am working with a .dll in LabView 5.1. I finished a little program that should give me the number of CPCI-cards in a PXI-machine. But now i always get the error messages "Call Library Function - Function not found in library". I know it is threated several times bfore on this forum, but i didn't exactly find a sollution that solved my problem.
    The .dll is documented and i can see the function names by opening the .dll with Quick View. I have checked (a hundred times) the names i typed in and they are correct (=equal to manual of .dll and to Quick View, so we can skip that).
    What else could be wrong? What can i do?
    Regards,
    Klaas Engels
    student

    I'm not sure if it's a reason, but once I had the same error. In my case the reason was in that DLL function was actually named with additional suffix letter "A", and then digging through MS documentation I've found an explanation that MS uses desired function with one or another suffix depending on usage contents and data type. Adding that suffix was solved the problem.
    This was not obvios because in DLL description there was no mentions at all and function name was given generally, i.e. without any suffix at all, assuming every user should be MS guru.
    Sergey

  • HT204074 The "Manage Devices" function not found in iTune

    I cannot find the "Manage Devices" function in the iTune Account Information screen.  Any help?

    The Function not found error is thrown when the OS can't provide the pointer to the function in the library to LabVIEW for some reason. For more information and common solutions see:
    http://digital.ni.com/public.nsf/websearch/44E40ACF1644DB77862562990054D672?OpenDocument
    The only reason I can think of why the first time it works correctly is that the DLL is not correctly clean-up by the close functions. Thus causing a second request for the pointer to fail due to this. (closing LabVIEW will remove the DLL form memory and thus probably clearing the error).
    Hope this Helps
    Kind regards,
    Karsten
    Applications Engineer
    National Instruments

  • PLEASE help..class function not found..

    I am writing a simple email validation and I get a TON of errors.
    1) is Class function not found. on - function validateEmail();
    2) and 11 Undefined variable or class name: document .
    The code is listed below -
    <html>
    <head>
    <meta http-equiv="Content-Language" content="en-us">
    <meta http-equiv="Content-Type" content="text/html; charset=windows-1252">
    <meta name="GENERATOR" content="Microsoft FrontPage 4.0">
    <meta name="ProgId" content="FrontPage.Editor.Document">
    <title>New Page 1</title>
    <%
    function validateEmail();
    if (document.forms[0].EMAIL_ADDRESS.value.length != 0)
    if ( (document.forms[0].EMAIL_ADDRESS.value.indexOf("@") == -1) ||
    (document.forms[0].EMAIL_ADDRESS.value.charAt(0) == ".") ||
    (document.forms[0].EMAIL_ADDRESS.value.charAt(0) == "@") ||
    (document.forms[0].EMAIL_ADDRESS.value.length < 6) ||
    (document.forms[0].EMAIL_ADDRESS.value.indexOf(".") == -1) ||
    (document.forms[0].EMAIL_ADDRESS.charAt(document.forms[0].EMAIL_ADDRESS.value.indexOf("@")+1) == ".") ||
    (document.forms[0].EMAIL_ADDRESS.value.charAt(document.forms[0].EMAIL_ADDRESS.value.indexOf("@")-1) == ".") ||
    (document.forms[0].EMAIL_ADDRESS.value.charAt(0) == ' ') )
    alert ("Please enter valid email address");
    document.forms[0].EMAIL_ADDRESS.focus();
    document.forms[0].EMAIL_ADDRESS.select();
    return false;
    else
    return true;
    %>
    </head>
    -- lots of input fields with the last being -
    <input type="text" name=EMAIL_ADDRESS onBlur="validateEmail();"></td>
    ????

    When I remove tags <% %> all of the function ends up in html and thus on my page.
    <html>
    <head>
    <meta http-equiv="Content-Language" content="en-us">
    <meta http-equiv="Content-Type" content="text/html; charset=windows-1252">
    <meta name="GENERATOR" content="Microsoft FrontPage 4.0">
    <meta name="ProgId" content="FrontPage.Editor.Document">
    <title>New Page 1</title>
    <%
    function validateEmail();
    if (document.forms[0].EMAIL_ADDRESS.value.length != 0)
    if ( (document.forms[0].EMAIL_ADDRESS.value.indexOf("@") == -1) ||
    (document.forms[0].EMAIL_ADDRESS.value.charAt(0) == ".") ||
    (document.forms[0].EMAIL_ADDRESS.value.charAt(0) == "@") ||
    (document.forms[0].EMAIL_ADDRESS.value.length < 6) ||
    (document.forms[0].EMAIL_ADDRESS.value.indexOf(".") == -1) ||
    (document.forms[0].EMAIL_ADDRESS.charAt(document.forms[0].EMAIL_ADDRESS.value.indexOf("@")+1) == ".") ||
    (document.forms[0].EMAIL_ADDRESS.value.charAt(document.forms[0].EMAIL_ADDRESS.value.indexOf("@")-1) == ".") ||
    (document.forms[0].EMAIL_ADDRESS.value.charAt(0) == ' ') )
    alert ("Please enter valid email address");
    document.forms[0].EMAIL_ADDRESS.focus();
    document.forms[0].EMAIL_ADDRESS.select();
    return false;
    else
    return true;
    %>
    </head>
    <body bgcolor="powderblue">
    <Form Name="My Form" Action=userInfoInsert.jsp Method=Post>
    <table border="0" width="100%">
    <tr>
    <td width="100%">
    <table border="0" width="100%">
    <tr>
    <td width="41%">First Name     <input type="text" name=FIRST_NAME ></td>
    <td width="59%">Last Name
    <input type="text" name=LAST_NAME ></td>
    </tr>
    </table>
    </td>
    </tr>
    <tr>
    <td width="100%">Address         
    <input type="text" name=Address ></td>
    </tr>
    <tr>
    <td width="100%">Address         
    <input type="text" name=Address ></td>
    </tr>
    <tr>
    <td width="100%">
    <table border="0" width="100%">
    <tr>
    <td width="32%">City            
       <input type="text" name=CITY size=10></td>
    <td width="18%">State
    <input type="text" name=STATE size=5></td>
    <td width="50%">Zip Code
    <input type="text" name=ZIP_CODE size=10 ></td>
    </tr>
    </table>
    </td>
    </tr>
    <tr>
    <td width="100%">Phone #         
    <input type="text" name=PHONE size="15" ></td>
    </tr>
    <tr>
    <td width="100%">SSN              
    <input type="text" name=SSN size="17" ></td>
    </tr>
    <tr>
    <td width="100%">
    <table border="0" width="100%">
    <tr>
    <td width="41%">Hint Question <input type="text" name=FIRST_NAME ></td>
    <td width="59%">Hint Answer <input type="text" name=LAST_NAME ></td>
    </tr>
    </table>
    </tr>
    <tr>
    <td width="100%">User Name     <input type="text" name=USER_NAME ></td>
    </tr>
    <tr>
    <td width="100%">Password        <input type="text" name=PASSWORD ></td>
    </tr>
    <tr>
    <td width="100%">Re-Password  <input type="text" name=RE_PASSWORD ></td>
    </tr>
    <tr>
    <td width="100%">Email Address
    <input type="text" name=EMAIL_ADDRESS onBlur="validateEmail();"></td>
    </tr>
    </table>
    <INPUT type=Submit Value=Submit>
    </form>
    </body>
    </html>

  • Function not found in library? 1127 switch module

    I am trying to control individual relays in an 1127 switch module with a 1331 attached.  Whenever I try to connect to it through the block diagram (or through example programs) I get an error stating "Function not found in library" or sub vi not executable. However when I try to control it from the switch executive front panel it seems to work correctly. When I follow the sub vi error chain I eventually arrive at the library node and I am told to configure it. However when I click configure I get options that are phrased slightly differently than the original sub vi name. How do I get the example code / control over the 1127 installed in an scxi chassis.

    Raaron,
    The SCXI 1127 is a Matrix / Multiplexer card. If we wanted to try to make it function similar to an SPDT, you will limit the number of "SPDTs" you can create. With the 1331 that can only be configured as a multiplexer and essentially used for a single "SPDT" [com(SPDT) = com (Mux), NC(SPDT) = Ch0 (Mux), NO(SPDT) = Ch1 (Mux)] . If you use the 1332 you have a 4x8 Matrix and can make it into 4 "SPDTs" [com(SPDT) = r0(Matrix), NC(SPDT) = c0(Matrix), NO(SPDT) = c1 (matrix)]. Both of these configurations will not really be normally closed, and you would have to configure it in software to close when you are using it.
    If you are looking for a true SPDT I would look at the 1160, 1161 and 1166.
    I am glad that it is working now, but I am still confused as to how you were having SW issues though. Maybe the device was being set up as a Traditional DAQ device and was installed on an OS that does not support Traditional DAQ? Resetting the device [for DAQmx use] may have fixed this? I am unsure without further information.
    Frank,
    National Instruments
    Staff Software Project Engineer

  • Where's the Contact search function?!

    I updated my iPhone to 2.02 already, but can't find where's the contact search function.

    Allan Sampson wrote:
    To quickly move to the top of your contact list, tap on the menu bar for lack of a better term.
    Doesn't work for me. Had to revert to ordinary finger-scrolling.

  • I keep trying to load firefox 6 and keep getting this error - The requested URL /cse?cx=partner-pub-3540673482024757:xbhdw8hkfz5&ie=ISO-8859-1&q=&sa=Search was not found on this server. That's all we know. in English

    I keep trying to load firefox 6 and keep getting this error - The requested URL /cse?cx=partner-pub-3540673482024757:xbhdw8hkfz5&ie=ISO-8859-1&q=&sa=Search was not found on this server. That’s all we know. in English

    Bookmark and use this;
    Download the '''[https://addons.mozilla.org/en-US/firefox/addon/searchreset/ Mozilla Search Reset]''' {web link}
    This add-on is very simple: on installation, it backs up
    and then resets your search preferences and home page
    to their default values, and then uninstalls itself. This
    affects the search bar, URL bar searches, and the home page.
    Sometimes a problem with Firefox may be a result of malware installed on your computer, that you may not be aware of.
    You can try these free programs to scan for malware, which work with your existing antivirus software:
    * [http://www.microsoft.com/security/scanner/default.aspx Microsoft Safety Scanner]
    * [http://www.malwarebytes.org/products/malwarebytes_free/ MalwareBytes' Anti-Malware]
    * [http://support.kaspersky.com/viruses/disinfection/5350 Anti-Rootkit Utility - TDSSKiller]
    * [http://general-changelog-team.fr/en/downloads/viewdownload/20-outils-de-xplode/2-adwcleaner AdwCleaner] (for more info, see this [http://www.bleepingcomputer.com/download/adwcleaner/ alternate AdwCleaner download page])
    * [http://www.surfright.nl/en/hitmanpro/ Hitman Pro]
    * [http://www.eset.com/us/online-scanner/ ESET Online Scanner]
    [http://windows.microsoft.com/MSE Microsoft Security Essentials] is a good permanent antivirus for Windows 7/Vista/XP if you don't already have one.
    Further information can be found in the [[Troubleshoot Firefox issues caused by malware]] article.
    Did this fix your problems? Please report back to us!

  • Function not found in library when I compile .so file in linux

    I am trying to get a driver for a california instruments power supply
    working under Linux. The drivers called DLLs compiled under windows I
    think. When I use those, the DLL could not be opened, so I compiled the
    DLL source under Linux. When I use the nm -g on the .so file, I get a
    list of all of the external functions including the ones I am trying to
    call from Labview, but when I try to run I get "function not found in
    library when I compile .so file in linux" even though I can see the
    function using nm. Is there something special I need to do to this .so
    file so Labview can read it?
    Any help would be greatly appreciated.
    Steiner

    Hello Steve,
    I'm not sure if simply recompiling the source code of the dll will be enough to create a Linux driver. I'm assuming the DLL makes some windows specific calls that are not supported in linux. How were you able to compile it in linux BTW? Did you have to change the code around to make it work?
    Your best bet would be to probably try to find a linux version of the driver from the manufactrurer itself.
    Regards,
    Jack J.
    Applications Engineer
    National Instruments

  • Function not found when package name exists with same name as schema name

    Hi all, any help would be appreciated :)
    I found an issue with pl/sql resolving a functions location when the db has a package name with the same as the db schema name.
    My example:
    -- arbitrary test function, not in any package
    create or replace FUNCTION testFunc
         inTest     IN VARCHAR2
    RETURN VARCHAR2
    AS
    BEGIN
    RETURN 'a';
    END;
    -- There is a package called "FM" with functions that are not referenced or used in this example and the db schema is "FM".
    -- The following PL/SQL fails with the message: "ORA-00904: "FM"."TESTFUNC": invalid identifier"
    select cursor (select testFunc('a') from dual) from dual;
    -- The following PL/SQL works:
    select * from (select testFunc('a') from dual);
    As mentioned the function testFunc is NOT in the FM package. This issue does not happen when I remove the FM package. So it seems like there is an issue with cursors calling functions when there exists any package with the same name as the db schema.
    Can anyone tell me why this happens and also what I can add to force the function that is not in any package to be referenced (without Oracle trying to look in the FM package)?
    DB: Oracle 11.2.0.2
    thanks!
    Paul

    Hi Paul,
    In general I would not advice to have schema and objects with the same name.
    Here is what documentation is saying here: How Name Resolution Differs in PL/SQL and SQL
    PL/SQL uses the same name-resolution rules as SQL when the PL/SQL compiler processes a SQL statement, such as a DML statement. For example, for a name such as HR.JOBS, SQL matches objects in the HR schema first, then packages, types, tables, and views in the current schema.
    PL/SQL uses a different order to resolve names in PL/SQL statements such as assignments and subprogram calls. In the case of a name HR.JOBS, PL/SQL searches first for packages, types, tables, and views named HR in the current schema, then for objects in the HR schema.As you can see above when using PL/SQL for your case Oracle searches first for packages, types, tables, and views named FM in the current schema, then for objects in the FM schema.
    And because a package FM is found it is raising an error due to the fact that the procedure could not be found in that package.
    I hope this clarify.
    Regards.
    Al

  • JCO RFC provider: Server function not found, short dump

    Hi all,
    I'm trying to use the JCO RFC provider service of NW04s (SP15) together with an ABAP 4.6C system. I've followed all the documentation that I could find, but couldn't get it to work yet. This is what I've done so far:
    Using SM59 I've had a destination APP_JK1 created for me on the R/3 system. AFAIK it's set up correctly and marked as a "registered server", connection tests were successful.
    On the portal, I've created a RFC portal destination using my R/3 credentials and successfully tested it. Then I created an entry in the RFC provider service, using the correct values for system, id & gateway, and let it point to my RFC destination for the repository connection. The program ID is also APP_JK1.
    Next, I created a stateless session bean which is part of an EAR, gave it a JNDI name of "RFCTEST" and added a method like this:
        * @ejb.interface-method view-type="both"
        * @param function called function
       public void processFunction(com.sap.mw.jco.JCO.Function function) {
          JCO.ParameterList input  = function.getImportParameterList();
          String query = input.getString("I_STRING_SEARCH");
          JCO.ParameterList output = function.getExportParameterList();
          output.setValue(query, "ECHOTEXT");
    (The project uses xdoclet for the creation of J2EE stuff)
    In application-j2ee-engine.xml located in the META-INF directory of my EAR, I've added:
    <reference reference-type="hard">
         <reference-target provider-name="sap.com" target-type="library">com.sap.mw.jco</reference-target>
    </reference>
    The application deploys without errors, and besides from my RFC connection works as expected. In the JNDI registry view of VisualAdmin I see the corresponding entry: "rfcaccessejb/RFCTEST" is a local reference to my stateless session bean.
    On ABAP, I have a tiny little program that calls my function, mainly looking like this:
    CALL FUNCTION 'RFCTEST' DESTINATION 'APP_JK1'
      EXPORTING
        I_STRING_SEARCH = query
      IMPORTING
        ECHOTEXT = t1.
    Unfortunately, it short dumps immediately. The error message is:
    JCO.Server could not find server function 'RFCTEST'
    I'm lost. What could be wrong? Any help is greatly appreciated. Kind regards,
    Christian Aust

    Hello Perry song,
    You got the short dump bcoz, there is no perform by the name you provided in the program,
    for example. consider there are 2 programs.
    Program 1 :
    REPORT  ZPGM1.
    *Calling a perform SNAME1 , the code of perform is written in ZPGM2.
    perform sname1 IN PROGRAM ZPGM2.
    Program 2 :
    REPORT  ZPGM2.
    perform sname1 .
    Form SNAME1 .
    write : 'Text in form SNAME1' .
    endform.                    " SNAME1
    (here SNAME1 is found and it works perfectly )
    Change in Program 1 :
    REPORT  ZPGM1.
    *Calling perform DELTA ,
    perform DELTA IN PROGRAM ZPGM2 IF FOUND.
    Now the perform statement will search for perform " DELTA " in ZPGM2 , but there is no perform by name DELTA , so here we need to mention the condition " IF FOUND "  , so now by mentioning the condition " IF FOUND " in perform statement ,  if the perform DELTA is not found then it wont go to DUMP.
    If condition " IF FOUND "  is not mentioned in perform statement like
    perform DELTA IN PROGRAM ZPGM2 . ( This gives DUMP )
    just type " IF FOUND " when u r calling a perform from other program ( i guess this will solve the problem ).
    Hope it might be helpfull,
    Regards ,
    Aby
    Edited by: abhi on Nov 6, 2008 10:14 AM

  • Search function not working correctly

    I have a problem searching in a specific document. For some reason, the search function only seems to sift through certain fonts, or types of text. The main text is not included in the search, but rather only (for example) the Table of Contents and some "examples" (in a special font) in the text. Everything else is omitted.
    When I copy/paste the main text, it's pasted as a strange code in this fashion, despite the fact that it's quite readable in it's original form:
    äíÉí=áåíÉ=Ü~ê=Ñí
    This is probably the reason why Search can't find terms in the main text, as searchable text looks quite right when copy/pasted. But how can I solve the problem?
    Thanks!
    David

    Did you check under the file Properties to see if the fonts are embedded? If they are not, you can reembed the fonts if you have Acrobat Pro using the Preflight tools.

Maybe you are looking for

  • How to show network status in top toolbar?

    how to show network status in top toolbar? Network preferences is there, but network status has disappeared on last reset of Airport Express, but may not be connected. Thanks in advance for practical help

  • Client copy/Syatem Copy

    Hi, What is the difference between client copy and system copy. and when client copy is don eall the Logical system names are replcec with the new logical system name in SPRO-G/L Account setings.How to prevent the same. Thanks, Venky

  • Find the partition for the fact table

    Oracle version : Oracle 10.2 I have one fact table with daily partitions. I am inserting some test data in this table for old date 20100101. I am able to insert this record in this table as below insert into fact_table values (20100101,123,456); Howe

  • Running 5 commands using array elements and waiting between?

    Hi All, Trying to learn PS so please be patient with me ;) System: PSv3 on Win2012 server running WSUS role I am wanting to execute 5 commands using a 'foreach' loop but wait until one finishes before moving onto the next. Can you please check out wh

  • ALSA sound not working. "-2 file not found"?

    I recently upgraded my system, changed some hardware and other things and now have figured out my sound is broken. Here is what I get: [earlz@EarlzAlpha spotify]$ speaker-test speaker-test 1.0.27.2 Playback device is default Stream parameters are 480