Control chart limit calculation not being done

Hi
I have maintained MIC, sampling procedure and Insp plan for a char and have made two lots with them. Though charts are being displayed correctly, control limit calculation is not being possible. Msg is "Control limits for track 1 could not be calculated".
What customization should be made for this?
And in QGC1/2/3, only one insp lot is there, what went wrong?

Dear Gajesh,
I tried with status 3. When i remove lot created start date, it shows me the fist lot with which we statred SPC in SAP. But If i put any specified start date, it returns no value. Does that mean with status 3 it will show the very 1st lot with which SPC usage started? Then what are the cases for status 1 and 5?
My sampling procedure setting is:
sampling type: Fixed sample
Valuation mode: SPC inspection
W/O inspection point
Sample size: 1
Chart type:115 Shewhart chart for X bar/USA
Inspection plan setting is:
SPC criterion : 020 task list char/materia
Base qty : 1KG
Thanks!

Similar Messages

Thunderbird junk controls in Account Settings not being recognized

I recently switched over to Thunderbird, and for the most part all is going well except for the account junk settings. When I go to the junk settings section for my POP account or for Local Folders, try to change something, and click OK, the changes do not take effect; when I go back to the junk settings section all of the old settings are still in place. Even switching to another section on account settings and back results in the junk settings being reverted. This doesn't happen for the global junk settings in the preferences box, nor does it happen for any other section of the account settings box. I looked in about:config to see if I could set the junk settings there but it appears that only the global junk settings have entries. Has anyone else had this problem? I'm using Thunderbird 13.0.1-1 from the repositories.

I don't recommend it because you'd loose all training information. So you'd need to start from scratch again should you decide to get back to the TB built-in junk filter.
I'm not sure I really understood your problem. By disabling TB junk mail controls, no new messages are being checked and eventually marked as junk by Thunderbird. Isn't that good enough?

Control-break statements:value not being displayed.

Hi all,
Iam using the control break statement at end of ..., sum.
value is not being displayed,instead it is showing *********.
even in the debugging mode the value is not being displayed.
iam passing the values into a temp IT,but still the values are not being dispalyed.
here is the following snippet of code.
what could be the mistake?
Please give me the suitable answer.
Thanks in advance.
LOOP AT FT_ITAB INTO FT_WA.
    FTY_WA-EBELN = FT_WA-EBELN.
    FTY_WA-EBELP = FT_WA-EBELP.
    FTY_WA-NAME1 = FT_WA-NAME1.
    FTY_WA-ZTERM = FT_WA-ZTERM.
    FTY_WA-INCO1 = FT_WA-INCO1.
    FTY_WA-WAERS = FT_WA-WAERS.
    FTY_WA-SUBMI = FT_WA-SUBMI.
AT END OF EBELN.
    SUM.
    FTY_WA-BRTWR = FT_WA-BRTWR.
    FTY_WA-KTMNG = FT_WA-KTMNG.
    FTY_WA-NETPR = FT_WA-NETPR.
   APPEND FTY_WA TO FTY_ITAB.
   CLEAR FTY_WA.
ENDAT.

Abhi,
i tried as you said values are being diplayed,but they are not gettin totaled,i want the sum of values at the end of line item,I need to pass these valuse to alv.
here is the complete code.Please tell me how should I proceed.
TABLES:EKKO,EKPO,LFA1.
TYPE-POOLS:SLIS.
DATA:HEADER TYPE SLIS_T_FIELDCAT_ALV,
     WA TYPE SLIS_FIELDCAT_ALV,
     LAYOUT TYPE SLIS_LAYOUT_ALV.
TYPES:BEGIN OF PH_TY,
        PH_EBELN LIKE EKKO-EBELN,
        PH_AEDAT LIKE EKKO-AEDAT,
        PH_LIFNR LIKE EKKO-LIFNR,
        PH_ZTERM LIKE EKKO-ZTERM,
        PH_EKORG LIKE EKKO-EKORG,
        PH_WAERS LIKE EKKO-WAERS,
        PH_SUBMI LIKE EKKO-SUBMI,
        PH_INCO1 LIKE EKKO-INCO1,
        PO_EBELN LIKE EKPO-EBELN,
        PO_EBELP LIKE EKPO-EBELP,
        PO_BRTWR LIKE EKPO-BRTWR,
        PO_KTMNG LIKE EKPO-KTMNG,
        PO_NETPR LIKE EKPO-NETPR,
      END OF PH_TY.
TYPES:BEGIN OF PO_TY,
        PO_EBELN LIKE EKPO-EBELN,
        PO_EBELP LIKE EKPO-EBELP,
        PO_BRTWR LIKE EKPO-BRTWR,
        PO_KTMNG LIKE EKPO-KTMNG,
        PO_NETPR LIKE EKPO-NETPR,
      END OF PO_TY.
TYPES:BEGIN OF VO_TY,
         VO_LIFNR LIKE LFA1-LIFNR,
         VO_NAME1 LIKE LFA1-LIFNR,
      END OF VO_TY.
TYPES:BEGIN OF FI_TY,
         EBELN LIKE EKKO-EBELN,
       AEDAT LIKE EKKO-AEDAT,
       LIFNR LIKE EKKO-LIFNR,
         ZTERM LIKE EKKO-ZTERM,
       EKORG LIKE EKKO-EKORG,
         WAERS LIKE EKKO-WAERS,
         SUBMI LIKE EKKO-SUBMI,
         INCO1 LIKE EKKO-INCO1,
       EBELN_I LIKE EKPO-EBELN,
         EBELP   LIKE EKPO-EBELP,
         NAME1 LIKE LFA1-LIFNR,
         BRTWR LIKE EKPO-EBELN,
         KTMNG LIKE EKPO-EBELN,
         NETPR LIKE EKPO-EBELN,
       LIFNR1 LIKE LFA1-LIFNR,
      END OF FI_TY.
TYPES:BEGIN OF FT_TY,
         EBELN LIKE EKKO-EBELN,
         ZTERM LIKE EKKO-ZTERM,
         WAERS LIKE EKKO-WAERS,
         SUBMI LIKE EKKO-SUBMI,
         INCO1 LIKE EKKO-INCO1,
         EBELP LIKE EKPO-EBELP,
         NAME1 LIKE LFA1-LIFNR,
         BRTWR LIKE EKPO-EBELN,
         KTMNG LIKE EKPO-EBELN,
         NETPR LIKE EKPO-EBELN,
      END OF FT_TY.
DATA: PH_ITAB TYPE STANDARD TABLE OF PH_TY,
      PO_ITAB TYPE STANDARD TABLE OF PO_TY,
      VO_ITAB TYPE STANDARD TABLE OF VO_TY,
      FI_ITAB TYPE STANDARD TABLE OF FI_TY,
      FT_ITAB TYPE STANDARD TABLE OF FT_TY,
      FTY_ITAB TYPE STANDARD TABLE OF FT_TY,
      FTY1_ITAB TYPE STANDARD TABLE OF FT_TY.
DATA:PH_WA LIKE LINE OF PH_ITAB,
     PO_WA LIKE LINE OF PO_ITAB,
     VO_WA LIKE LINE OF VO_ITAB,
     FI_WA LIKE LINE OF FI_ITAB,
     FT_WA LIKE LINE OF FT_ITAB,
     FT_WA1 LIKE LINE OF FT_ITAB,
     FTY_WA LIKE LINE OF FT_ITAB,
     FTY1_WA LIKE LINE OF FT_ITAB.
SELECT A~EBELN
       A~AEDAT
       A~LIFNR
       A~ZTERM
       A~EKORG
       A~WAERS
       A~SUBMI
       A~INCO1
       B~EBELN
       B~EBELP
       B~BRTWR
       B~KTMNG
       B~NETPR
       INTO TABLE PH_ITAB FROM EKKO AS A
       INNER JOIN EKPO AS B
       ON AEBELN = BEBELN
       UP TO 25 ROWS.
CHECK PH_ITAB[] IS NOT INITIAL.
SELECT LIFNR
       NAME1
       FROM LFA1 INTO TABLE VO_ITAB
       FOR ALL ENTRIES IN PH_ITAB
       WHERE LIFNR = PH_ITAB-PH_LIFNR.
CHECK VO_ITAB[] IS NOT INITIAL.
SORT PH_ITAB BY PH_EBELN.
SORT VO_ITAB BY VO_LIFNR.
LOOP AT PH_ITAB INTO PH_WA.
FI_WA-SUBMI = PH_WA-PH_SUBMI.
FI_WA-EBELN = PH_WA-PH_EBELN.
FI_WA-ZTERM = PH_WA-PH_ZTERM.
FI_WA-INCO1 = PH_WA-PH_INCO1.
FI_WA-WAERS = PH_WA-PH_WAERS.
FI_WA-EBELP = PH_WA-PO_EBELP.
FI_WA-BRTWR = PH_WA-PO_BRTWR.
FI_WA-KTMNG = PH_WA-PO_KTMNG.
FI_WA-NETPR = PH_WA-PO_NETPR.
READ TABLE VO_ITAB INTO VO_WA WITH KEY VO_LIFNR = PH_WA-PH_LIFNR BINARY SEARCH.
FI_WA-NAME1 = VO_WA-VO_NAME1.
APPEND FI_WA TO FI_ITAB.
CLEAR FI_WA.
ENDLOOP.
LOOP AT FI_ITAB INTO FI_WA.
    FT_WA-EBELN = FI_WA-EBELN.
    FT_WA-EBELP = FI_WA-EBELP.
    FT_WA-NAME1 = FI_WA-NAME1.
    FT_WA-ZTERM = FI_WA-ZTERM.
    FT_WA-INCO1 = FI_WA-INCO1.
    FT_WA-WAERS = FI_WA-WAERS.
    FT_WA-SUBMI = FI_WA-SUBMI.
    FT_WA-BRTWR = FI_WA-BRTWR.
    FT_WA-KTMNG = FI_WA-KTMNG.
    FT_WA-NETPR = FI_WA-NETPR.
APPEND FT_WA TO FT_ITAB.
CLEAR FT_WA.
ENDLOOP.
LOOP AT FT_ITAB INTO FT_WA.
AT END OF EBELN.
SUM.
    FTY_WA-EBELN = FT_WA-EBELN.
    FTY_WA-EBELP = FT_WA-EBELP.
    FTY_WA-NAME1 = FT_WA-NAME1.
    FTY_WA-ZTERM = FT_WA-ZTERM.
    FTY_WA-INCO1 = FT_WA-INCO1.
    FTY_WA-WAERS = FT_WA-WAERS.
    FTY_WA-SUBMI = FT_WA-SUBMI.
    FTY_WA-BRTWR = FT_WA-BRTWR + FTY_WA-BRTWR.
    FTY_WA-KTMNG = FT_WA-KTMNG + FTY_WA-KTMNG.
    FTY_WA-NETPR = FT_WA-NETPR + FTY_WA-KTMNG.
ENDAT.
   APPEND FTY_WA TO FTY_ITAB.
   CLEAR FTY_WA.
ENDLOOP.
WA-SELTEXT_L = 'ebeln'.
WA-COL_POS = '1'.
WA-FIELDNAME = 'EBELN'.
WA-TABNAME = 'FTY_ITAB'.
WA-OUTPUTLEN = '15'.
APPEND WA TO HEADER.
CLEAR WA.
WA-SELTEXT_L = 'SUBMI'.
WA-COL_POS = '2'.
WA-FIELDNAME = 'SUBMI'.
WA-TABNAME = 'FTY_ITAB'.
WA-OUTPUTLEN = '15'.
APPEND WA TO HEADER.
CLEAR WA.
WA-SELTEXT_L = 'NAME1'.
WA-COL_POS = '3'.
WA-FIELDNAME = 'NAME1'.
WA-TABNAME = 'FTY_ITAB'.
WA-OUTPUTLEN = '15'.
APPEND WA TO HEADER.
CLEAR WA.
WA-SELTEXT_L = 'ZTERM'.
WA-COL_POS = '4'.
WA-FIELDNAME = 'ZTERM'.
WA-TABNAME = 'FTY_ITAB'.
WA-OUTPUTLEN = '15'.
APPEND WA TO HEADER.
CLEAR WA.
WA-SELTEXT_L = 'INCO1'.
WA-COL_POS = '5'.
WA-FIELDNAME = 'INCO1'.
WA-TABNAME = 'FTY_ITAB'.
WA-OUTPUTLEN = '15'.
APPEND WA TO HEADER.
CLEAR WA.
WA-SELTEXT_L = 'WAERS'.
WA-COL_POS = '6'.
WA-FIELDNAME = 'WAERS'.
WA-TABNAME = 'FTY_ITAB'.
WA-OUTPUTLEN = '15'.
APPEND WA TO HEADER.
CLEAR WA.
WA-SELTEXT_L = 'brtwr'.
WA-COL_POS = '7'.
WA-FIELDNAME = 'BRTWR'.
WA-TABNAME = 'FTY_ITAB'.
WA-OUTPUTLEN = '20'.
APPEND WA TO HEADER.
CLEAR WA.
WA-SELTEXT_L = 'netpr'.
WA-COL_POS = '8'.
WA-FIELDNAME = 'NETPR'.
WA-TABNAME = 'FTY_ITAB'.
WA-OUTPUTLEN = '20'.
APPEND WA TO HEADER.
CLEAR WA.
WA-SELTEXT_L = 'ktmng'.
WA-COL_POS = '9'.
WA-FIELDNAME = 'KTMNG'.
WA-TABNAME = 'FTY_ITAB'.
WA-OUTPUTLEN = '20'.
APPEND WA TO HEADER.
CLEAR WA.
CALL FUNCTION 'REUSE_ALV_GRID_DISPLAY'
EXPORTING
    I_CALLBACK_PROGRAM = SY-REPID
    IT_FIELDCAT        = header[]
TABLES
    T_OUTTAB           = FTY_ITAB[].
IF SY-SUBRC = 0.
ENDIF.

Cron.hourly jobs not being done

Hi.
I've just completed a clean re-install. However a script I placed in /etc/cron.hourly only gets run every two hours. At first I thought I had made a mistake with the script so I added a 'logging' entry in the script and also in the file /etc/cron.hourly/adjtime. These and the /var/spool/cronstamps/root.sys-hourly entry confirm that they are only being run every two hours. I have been monitoring this for about 20 hours over three days and it is consistant. dcron version is 4.4-2. I have no idea what is wrong or how to sort it.
TIA
StewartT

ataraxia wrote:It's a bug; Jim knows about it. This started happening for me at the daylight savings time switch. I'm working around it myself by not using @hourly but instead setting an old-fashioned schedule with an exact minute.
Thanks for the reply. Of coarse the UK went to summer time last weekend. I'll use the same work around until it's fixed.
Thanks again.
StewartT

Adobe Professional - Calculation not being calculated

I created a form containing several fields where people
input numeric values. For the most part it is working however there is one box (the last box in red, where it doesn't calculate right away until they enter a number in another field. Why is that? Each time someone enters a number, that field should re-calculate right away after the user moves on to the next field.
I cannot figure this problem out, please help. I'm attaching a word document containing a screenshot of the problem. I'm also attaching the PDF form.
--Gilbert

Change the field calculation order.

Control chart tolerance limits lines not shown

As Run chart displays values of Single result, SPC Control charts also Displays these reults with tolerance limit with Showing lines of uper and lower limit Tolerence. I have an issue while showing these lines .when i am doing result recording control charts Some times shows tolerance limit lines and some times not ? Kindly clarify me the SPC control chart process too?but my main question is that why SAP some times shows Results and sometimes not .
More over I already did all settings as below
Sapmling procedure with Fixed samples ,and SPC inspection crieteria,
Inspection plan -Inspection task list cahracterstics
MIC
      Sampling proceudre -active
      SPC - Active
      Required Chrac.-Active
      Single result -Active
      Fixed scope -Active
All settings of number ranges is set
Control chart 115 -Shewchart X bar is using .

Hi Vineeth,
We are using SPC inspection chars, in results recordin it is not calulating the control limits automatically. When i click to calculate the control limits, getting the message Control limits for track 1 could not be calculated.
Can you please let me know
1) The process flow for SPC inspection results recording
2) How to get the control limits automatically for SPC inspection chars.
3) System will require some results to calculate control limts, right? So, till system calculates those control limits, how system will valuate results (will it be with specificaiton limits specified at inspection characteristics level), do we have any option of entering preliminary results so that system can control limits on bases of those results and so from very first inspection lot we have control limits for valuation?
Thanks in advance
Bob

SSRS 2008 Column Chart with Calculated Series (moving average) "formula error - there are not enough data points for the period" error

I have a simple column chart grouping on 1 value on the category axis. For simplicity's sake, we are plotting $ amounts grouping by Month on the category axis. I right click on the data series and choose "Add calculated series...". I choose moving average. I want to move the average over at least 2 periods.
When I run the report, I get the error "Formula error - there are not enough data points for the period". The way the report is, I never have a guaranteed number of categories (there could be one or there could be 5). When there is 2 or more, the chart renders fine, however, when there is only 1 value, instead of suppressing the moving average line, I get that error and the chart shows nothing.
I don't think this is entirely acceptable for our end users. At a minimum, I would think the moving average line would be suppressed instead of hiding the entire chart. Does anyone know of any workarounds or do I have to enter another ms. connect bug/design consideration.
Thank you,
Dan

I was having the same error while trying to plot a moving average across 7 days. The work around I found was rather simple.
If you right click your report in the solution explorer and select "View Code" it will give you the underlying XML of the report. Find the entry for the value of your calculated series and enter a formula to dynamically create your periods.
<ChartFormulaParameter Name="Period">
<Value>=IIf(Count(Fields!Calls.Value) >= 7 ,7, (Count(Fields!Calls.Value)))</Value>
</ChartFormulaParameter>
What I'm doing here is getting the row count of records returned in the chart. If the returned rows are greater than or equal to 7 (The amount of days I want the average) it will set the points to 7. If not, it will set the number to the amount of returned rows. So far this has worked great. I'm probably going to add more code to handle no records returned although in my case that shouldn't happen but, you never know.
A side note:
If you open the calculated series properties in the designer, you will notice the number of periods is set to "0". If you change this it will overwrite your custom formula in the XML.

Mid month period not being calculated in pay slip

Hi Experts,
Mid month period given in 0008 is not being calculated.
e.g. if i hire some one on 16.01.09, then 0008 data should be calculated for those days only (e.g. 16 days) in pay slip. But in my case it is taking full amount of 0008.
Can any one kindly help, pl.
thanks
Balu

Dear Sikindar,
thanks for the replay.
PCL 1 and PCL10 are having 3 and 1 respectively.
checked the control record and the pay roll area of that employee and generation of pay roll periods are available in V_T549Q.
please guide me further
thanks
Balu

The apexafterrefresh event not being fired in Chart IR's

Hi all,
I am adding additional functionality to IR reports using the plug-in architecture in Apex 4.1.1. A Dynamic action has been added to the "After Refresh" event for the #apexir_WORKSHEET_REGION jQuery selector.
This works fine in all cases except when no data is found in the report. This has been fixed in 4.2 so I can live with this until the upgrade. However, it also does not work when a chart is created in the report, the apexafterrefresh event does not get raised. Therefore my dynamic action will not fire. Looking at the apex_interactive_reports_4_1.js this event gets raised for the table element with an ID stored in apexir_WORKSHEET_ID ie:
apex.jQuery('#' + $v("apexir_WORKSHEET_ID")).trigger('apexafterrefresh', that.report_id);However this table element does not get rendered when a Chart is displayed and therefore the apexafterrefresh will not get raised.
In apex 4.2 the widget.interactiveReport.js has been modified to handle the no data found but not charts:
var lTriggeringElement$, lWorksheetId;
                        lWorksheetId = $v( "apexir_WORKSHEET_ID" );
                        if ( $x( lWorksheetId ) ) {
                            // If the table element containing data exists (ie when the report returns rows),
                            // use that to trigger the event.
                            lTriggeringElement$ = apex.jQuery( '#' + lWorksheetId );
                        } else {
                            // Otherwise, use the span holding the no data found message.
                            lTriggeringElement$ = apex.jQuery( '#apexir_NO_DATA_FOUND_MSG' );
                        lTriggeringElement$.trigger( 'apexafterrefresh', that.report_id );I have created a test case on apex.oracle.com - http://apex.oracle.com/pls/apex/f?p=41357:1 In this example I simply display an alert from a Dynamic action with the following attributes:
Event - After Refresh
Selection Type - Region
Region - Interactive Report
As can be seen when the user navigates to the report the alert displays, however when you navigate to the Chart the alert does not display.
In my mind this is a bug and the IR reports JavaScript should be modified to raise the event apexir_WORKSHEET DIV Element instead. This would fix both issues.
Any ideas on how to overcome this issue?
Thanks
Chris.

For everyone's information Bug 16029272 - ALERT (APEXAFTERREFRESH EVENT) NOT BEING FIRED IN CHART OF INTERACTIVE REPORTS has been raised regarding this issue.

My iPhone 5c is not being recognized by my mac except to charge it. I'm up to date on all updates and don't know what else to do. I have restarted several times. I have even tried to update my iPhoto and I can't even do that with iPhoto 9.0, but can't.

My Iphone 5c is not being recognized by my Mac computer. I have done all of the upates, restarted several times and I'm not sure what else to do. I have searched and searched and searched and have come up with nothing. Also, my Iphoto can not be updated. I'm still using version 8. something, and it won't update without this update and that update. It needs 9.0 but I can't find that download anywhere. The only one that I can find is 9.1. That won't update. Is there anything that I can do, or should I just bite it and take it to apple to get looked at?

Does iTunes not see the phone?
If not, make sure you're running the current version of iTunes.
If you are running the current version and it still doesn't recognize it, see this: http://support.apple.com/kb/TS1591?viewlocale=en_US&locale=en_US
As for iPhoto, you will have to purchase a newer version. It's not a free upgrade. Or, you can use Image Capture, which is built into OS X, to import the photos.

This is a stupid question but I needed to ask because I don't want to go there and not being able to buy it, but can I get the iPhone 5 brought straight there when I go to an apple store?

This is a stupid question but I needed to ask because I don't want to go there and not being able to buy it, but can I get the iPhone 5 brought straight there when I go to an apple store?

And I meant go to the apple store physically without preordering it online, and I meant the Southampton one. So could I just stroll in apple store and buy a iPhone 5 in Southampton apple store and buy the iPhone 5 straight away? Because I didn't want to have to wait? I just want to go in and buy it and go out with it, if you guys get what I mean? And felipeV if it is in stock could I just buy it and leave with my iPhone 5?

HT2534 in my iphone5 'none' option for credit card is not being appeared. May be because of software upgrade or wot it is really not good as i don't want to share my credit card number.

the 'none' option under payment methods is not being appeared in my iphone 5 as i don't want to share my credit card info. and my id stuck over that point as i am not abble to skip this step and it is a must option to select a credit card type and give a real credit card details. This is really not good.

You have to enter your credit card number and some amount would be debited from your account(60 rs in india)
After registration, You can Go to
1 Settings
2.Itunes&App Store
3.Click on your apple id .
4.Select View Apple ID
5.Slecet Payment Info
And You can find NONE here.
Please select NONE to delete your credit card numbe r from the list
But While registering you cant find NONE, you have to enter the cc number.
Thank You
Tejas

My apps are not being updated when pressing the update all button. It just says installing and no update is being done., my apps are not being updated when pressing the update all button. It just says installing and no update is being done.

my apps are not being updated when pressing the update all button. It just says installing and no update is being done., my apps are not being updated when pressing the update all button. It just says installing and no update is being done.

Must be serious because you have stated the problem 4 times now.
Here are a number of things that you can try and maybe one of them will help.
Reboot the iPad by holding down on the sleep and home buttons at the same time for about 10-15 seconds until the Apple Logo appears - ignore the red slider - let go of the buttons.
Make sure that you do not have a stalled download in iTunes - a song or podcast .... if you have a download in there that did not finish, complete that one first. Only one thing can download at a time on the iPad so that could be what is causing the problem.
If that doesn't work - sign out of your account, restart the iPad and then sign in again.
Settings>iTunes & App Store>Apple ID. Tap your ID and sign out. Restart the iPad by holding down on the sleep button until the red slider appears and then slide to shut off. To power up hold the sleep button until the Apple logo appears and let go of the button.
Go back to Settings>iTunes & App Store>Sign in and then try to update again. Tap one waiting icon only if necessary to start the download stream.
You can also try deleting the waiting icons - tap and hold down on an icon until it wiggles - the tap the X on the icon to delete it. Then try to download again.
You can try resetting all settings. Settings>General>Reset>Reset All Settings. You will have to enter all of your app preferences and device settings again.
You can also try going to the App Store, find an app that needs an update, tap on the app icon to bring up the description page, then tap on install that way, rather than using the Update option from the app updates screen.
And ... You can always install the updates in iTunes on your computer and then sync them to the iPad.

Employer Unemployment Tax Not Being calculated in US Payroll

Hi Experts,
Employer Unemployment Tax (Tax Type 10) for Tax Authority Alabama is not being calculated in US Payroll in my SAP system.
The taxable amt is showing up, but the tax is not being calculated in the payroll log.
No error/warning mssg is provided by BSI in the payroll log.
I have already checked for the following:
1)We are using the standard tax model 002 provided by SAP for Alabama
The tax model settings are fine.
2) Table T5UTX is being maintained.
3) Tax Type 10 is setup against tax auth Alabama in BSI Tax Factory.
For tax auth Federal too, though the taxable for tax type 10 shows up, tax is not being calculated.
Can you please help.
Regards,
Somdeb.

Hello Somdeb,
Please be aware that this is no standard SAP tax model only an example which must be customized as every customer is different.
First check the payroll log to see if the information is being sent to BSI TaxFactory. If not then the issue is mostly the tax model. Different tax models can be used based on the employee.
If the values are being sent to BSI and not being calculated, then there is an issue wil BSI. Send BSI the script and they will tell you what the issue is.
Regards,
Manny

[svn:osmf:] 14871: Fixing anchoring 'right' and 'bottom' properties not being applied on items that don't have a width/ height and position set.

Revision: 14871
Revision: 14871
Author:   [email protected]
Date:     2010-03-19 01:05:54 -0700 (Fri, 19 Mar 2010)
Log Message:
Fixing anchoring 'right' and 'bottom' properties not being applied on items that don't have a width/height and position set.
Modified Paths:
    osmf/trunk/framework/OSMF/org/osmf/layout/LayoutRenderer.as

If you're just doing it in a back and forth or spiral fashion, you don't need to check whether a square's been filled in. You just go from a start point to an end point. Those points and the squares in between are determined by simple arithmetic.
If you're doing it randomly, I wouldn't use the GUI elements themselves. I'd have, for example, and array of booleans that tells whether each square has been filled in.

Control chart limit calculation not being done

Similar Messages

Maybe you are looking for