Creating wireless network with Time Capsule

hi, I just have couple of questions before installing the time capsule;
so far I have been using cable DSL modem, so my question is - is it possible to set time capsule as a wireless router, or does time capsule still have to be connected with DSL modem and then act wiresly with iMac?
I was thinking if i could replace cable DSL modem with time capsule
thank you

The Time Capsule has to be connected to your DSL modem. Otherwise you won't be able to connect to internet.

Similar Messages

How can i extend a wireless network with time capsule

How can i extend an existing wifi verizon wireless network with time capsule? the router is connected on the bottom floor. want to boost the signal to a home office on the top floor, four flights up. connect time capsule via ethernet cable to iMac on 4th floor? Do I have to start a second wifi network or can I set it to just boost the one I have? thank you

How can i extend an existing wifi verizon wireless network with time capsule?
It all depends on what you mean by "extend".
If you plan to "extend" by connecting the Time Capsule to the Verizon router using a wired Ethernet cable, this can be accomplished.
If you were hoping to connect the Time Capsule to the Verizon router using wireless only, unfortunately the Time Capsule and Verizon products are not compatible for that purpose.
Check with Verizon to see if they offer an "extender" or "repeater" that could be located very close to the Time Capsule.
This would provide both more wireless coverage and also allow you to connect the Time Capsule using an Ethernet cable from the "extender" or "repeater".

Troubling extending wireless network with Time Capsule and Airport Extreme

I am trying to set up and extend a wireless network in my house, but it’s not working right. I have two Airport/Capsule units in the house:
2TB Time Capsule (Dual-Band II)
1 Airport Extreme (Dual Band)
I have the Verizon Fios router as my gateway to the internet, and also as my DHCP server. I have also tested the ethernet ports in my house to verify that they work, and that I can get a DHCP-issued IP address.
Now, my Verizon router has WiFI, and it’s still on. I am not using it though except to troubleshoot. So far as I understand, this should not cause a problem.
Base station setup
So I setup the TC to Create A New Wireless Network, on the ethernet network it’s on (Dlink switch plugged into Verizon router). I set it up in Bridge Mode (as opposed to having it dole out IPs, since the Verizon router does this already). The TC gets a valid IP, and my wireless device connect to it without a problem. I have checked “Allow this network to be expanded” under Wireless settings.
Extended station setup
The AE Dual-Band is plugged into the Ethernet, and is reset to Factory Settings. I name it “Airport Extreme 2” and I chose “I want Airport Extreme to join my current network.” The other two options are: “I want to create a new wireless network” and “I want to replace and existing base station or wireless router with Airport Extreme.”
I chose to “join,” I select “I want to connect Airport Extreme to my network using Ethernet to extend my existing wireless network.” The other options are to disable wireless entirely, or to “wirelessly join my current network.” On the next page it asks me to select the device or network that the Airport Extreme will connect to using the Ethernet. I set it to the Time Capsule.
Results:
Access near the Airport Extreme 2 is incredibly slow. Speedtest shows I am getting less than 1Mbps. Worse yet, my mail client won’t connect. It just times out.
What I had hoped was that the AE would connect via Ethernet to the network, and just bring the wireless network to the other side of the house. Instead it almost seems as though it is just re-amplifying the TC’s signal. Otherwise, why is performance so bad?
Thanks to anyone with some insight here!

Hello Kennuff. Welcome to the Apple Discussions!
Since you have the ability to connect all of the routers by Ethernet, there is no need to configure the Time Capsule (TC) & 802.11n AirPort Extreme Base Station (AEBSn) for a dynamic WDS (aka, extending a network). This option is only when the routers do NOT have an Ethernet connection between them.
Instead, you want to configure the TC & AEBSn in a "roaming" network. I suggest starting by performing either a "hard" or "factory default" reset on both.
Next be sure that both the TC & AEBSn are on the same Ethernet subnet coming from the Verizon-supplied router.
Configure the TC & AEBSn as follows:
AirPort Utility > Select the TC or AEBSn > Manual Setup > AirPort > Wireless
o Wireless Mode = Create a wireless network
o Allow this network to be extended: <not checked>
o Radio Mode: <leave the default or if you require a specific mode make sure both routers are configured the same>
o Wireless Security: <configure both routers the same>
AirPort Utility > Select the TC or AEBSn > Manual Setup > Internet > Internet Connection
o Connection Sharing = Off (Bridge Mode)

Extend FiOS wireless network with Time Capsule

I have a FiOS wifi router and a 1TB TC (with latest firmware 7.6.3). I'd like to extend the wireless network to cover some dead zones. I've run ethernet from the LAN port on the router to the WAN port on the Time Capsule, and it's getting an IP and internet connectivity. However, when I follow the Apple instructions to extend a wireless network, I get the warning error "unable to extend network" and the flashing orange light. I've confirmed the SSID and password are correct and match the FiOS SSID and password, and I've confirmed that the TC is in bridge mode. I've also logged into the FiOS router and confirmed it's assigning IPs to the wired and wireless componets of the TC, and recognizes the wireless is in bridge mode. Any suggestions?
I've got it working currently as a separate SSID, but it's just a pain to have to jump from weak-network1 to TC-network2 whenever I'm in a dead zone. Thanks in advance!

Check to make sure that you have the TC configured to.....
Create a wireless network (not "extend".....as that is only used for wireless extension and you are using Ethernet)
Use the exact same wireless network name (SSID) as the FIOS router
Use the exact same type of wireless security that the FIOS router is using (Make sure that this is not WEP) It should be WPA2 Personal or WPA/WPA2 Personal.
Same wireless password as the FIOS
Bridge Mode configuration
Unless everything matches up correctly, you will have two separate networks that require two separate log ons.
Configured correctly, you will have a "roaming" network. Your Mac will automatically switch over to the wireless access point with the best signal quality as it moves from one area to another.

Wireless Network with Time Capsule -- 2 Questions (5 GHz? 2nd Network?)

Hi all:
First off, thanks to all of you for being there. Apple Discussion Boards are the best!
OK, to start with, here's my gear list:
-iMac 27" QC (bought Dec. '09), 2.8 GHz, 8 GB RAM, running 10.6.4
-Time Capsule 802.11n, 1 TB (bought April '10)
-Airport Express 802.11n (bought April '10)
-iPad
-iPhone 4
So I set up the Time Capsule a few months ago, and paired it with my iMac and with the Airport Express (to stream AirTunes), and everything has been working fine.
The iPad and iPhone are also working fine. (In Airport Utility > Advanced > Logs, the iPhone shows a rate of 72, signal -60, and noise -94. And the iMac shows a rate of 300, signal -47, and noise -96. Don't know if that is good or bad or normal.)
So, here are my questions:
First, in Airport Utility > AirPort > Wireless > Wireless Network Options... should I check the box that says "5 GHz Network Name"? It is currently not checked. Would that increase performance? (All my devices - iPad, iPhone, Airport Express - are "n" devices, right? Does that mean I should check that box? Is that even an issue?)
Second, when I first set up my wireless network I named it "MP Network." But I notice in System Preferences > Airport > Advanced that there is another network that apparently was set up when I first set up the TC. Its name is "Apple Network" plus 3 letters and 3 numbers.
What is that? It doesn't show up anywhere else. Should I delete it? Is it using up bandwidth by being there?
(Both networks appear in that same place on System Preferences, and both are WPA2 Personal.)
Thanks to anyone for any input/advice. And apologies if any of the above is confusing.
Matt

+So it sounds like I should leave the network as is, right?+
Yes, this makes sense for most users. Some users sometimes have trouble with a new computer that sometimes connects to the 5 GHz network and sometimes connects to the 2.4 GHz network. They want the computer to always connect to the 5 GHz network so they assign a separate name to that network and configure their computer to connect to that network first.
+The iPhone being "g" does not reduce my overall performance, right?+
No, because it's using the 2.4 GHz band. Faster devices use the 5 GHz band.
+And my TC broadcasts dual band so the "n" devices get what they want and the "g" device gets what it wants...correct?+
Yes, but you need to remember that "n" devices can connect at either 2.4 GHz or 5 GHz.
+(The 300 Mbits/sec I am getting on my iMac is good, right? And is 72 for the iPhone good, too?)+
300 Mbps is outstanding. Most users average 220-270 with a good connection. The iPhone is a "g" device, which means it can operate up to 54 Mbps, so I'm not sure what you are seeing here.
+As for the other issue of the "out of the box" network name, I think I will delete it. (I am of the school that enjoys things clean and avoids unnecessary clutter!) But will that create any problems for me? Is it as simple as clicking the "-" (remove) icon in System Preferences > Network > AirPort tab?+
That's all you have to do.
I can't remember if the password for the Apple Network xxxxxxx is stored in Keychain Access.
Macintosh HD > Applications > Utilities > KeyChain Access
Look for a listing of the Apple Network xxxxxx and delete that entry if you want to remove all evidence of that network.

Extend wireless network with Time Capsule

I have a dual band Time Capsule in a two story house. The TC is upstairs, and I have an Airport Express downstairs to extend the wireless network. However, the speed is very slow downstairs. I have recently wired the downstairs with ethernet cable, and would like to use a wired wireless repeater (bridge) to get a better signal downstairs. What hardware should I use?

I have a similar but slightly different issue/question. I didn't know whether to start a new post but I will try here first. I'm not able to set up a 5GHz roaming network.
I am a self employed songwriter and need 5GHz speed for numerous devices that stream video and music (computers, DirecTv, Tivos, AppleTVs etc.). All these have both wireless cards and Ethernet cables connected for backup. I need the 2GHz radio only for iPhones or guests. I have ATT DSL with 5 static IP addresses. The first is assigned to TCdual and "shared". My older "L" shaped home is tuff on wireless signals (plaster walls etc). Since I've had a lot of trouble with WDS and wireless connections, years ago, I ran Ethernet to every network device as backup, including an Ethernet connected Airport Express, with wireless turned off, I dedicated exclusively to Remote Tunes. It's been working the past few months (knock on wood). But I need to extend TCdual's 5GHz network with roaming. Here's what I've tried without success.
I placed a 2nd Airport with 5GHz (the model before TC dual) in the room TC's 5GHz will not reach and connected it to TC via ethernet. Using Airport Utility, I tried to "extend" TC's 5GHz network. No luck. AU will only extend TC's default network, which is 2GHz. Very frustrating. So... the only way to get 5GHz in this room is to create a 2nd 5GHz network on Airport #2. Even using the same network name does not create roaming. Whenever I move MBP from this room, I lose Airport#2's 5GHz network and every WAN/LAN connection. I have to reconnect to TC's 5GHz network, every other WAN/LAN device, resume downloads, iChats etc. and start again. VERY frustrating. I think I must be missing something. Am I really forced to choose between speed or roaming. Can't I set up a 5GHz roaming network and have both?

Unable to Create Guest Network with Time Capsule

Time Capsule version: 7.6.1, AirPort Utility: 6.0(600.92), Cabel Modem Ambit U10C018, iMac w/ Mac OS X (10.7.3)
I have the Time Capsule installed as the only router. The Network settings, Router Mode is: DHCP and NAT. I am unable to find any tab or button for "Advanced" that will allow me to set up a guest network. I am pretty sure that cable modem does not function as a router because when I changed the Time Capsule to Bridge I was unable to make any wireless connections.
Any help woudl be greatly appreciated, but I will be away from the computer for the next 3 hours.

We will assume that your Time Capsule is not one of the 1st Generation models, which did not have Guest Network capability.
But, if your Time Capsule is a few years old, or you purchased it from another user....you may have a single band version of the product....which cannot offer the Guest Network option.
If your Time Capsule has the capability....here is how to set up the Guest Network
Open AirPort Utility and click on the Time Capsule icon that appears
Click Edit in the next window that appears
Click the Wireless tab at the top of the window
Enter a check mark next to Enable Guest Network
Edit the name of the network as you wish
Select Wireless Security...either WPA2 Personal or WPA/WPA2 Personal would be good
Enter a password for the Guest Network and verify
Click Update at the lower right

Creating home network with time capsule

Can a home net work be setup that allows for the extra Ethernet. Outputs to drive a printer?

Just to add to Bob's comment..
If you buy a switch.. buy gigabit.. they are cheap enough now.. and brand is not a big deal for unmanaged switch.. and buy one with enough ports for everything in the house and then some.. try not to use any port on the TC except the one uplink to the switch.. that tends to keep traffic in the switch where it belongs.
Printers these days are ethernet and wireless.. for very little extra.. either can be connected easily to the TC as it is merely a network client.. the printer itself handles the print jobs.. rather than using the usb on the TC which has limitations.

I'm trying to extend my wifi network with time capsule but it can't find the existing wifi network

I'm trying to extend my wifi network with time capsule but it can't find the existing BT wifi network even though it is there with a good signal strength. The Time Capsule is connected to a Netgear router via ethernet.

You will need to start over on the setup of the Time Capsule as follows:
Disconnect any Ethernet cables that might be connected to the Time Capsule, but leave it powered on
Hold in the reset button on the back of the Time Capsule for 8-10 seconds and release. The reset button is located next to the AC power socket.
Allow a full minute for the Time Capsule to restart to a slow, blinking amber light
Connect the Ethernet cable from a LAN <--> port on the Netgear to the WAN "O" port on the Time Capsule. The Ethernet cable must remain connected at all times.
Click the WiFi icon at the top of the Mac's screen
Look for a setting of New AirPort Base Station
Click on Time Capsule
The example below shows an AirPort Express. You will see Time Capsule on your screen.
That will get the setup wizard going. It will take a minute to analyze the settings, then display a screen that looks like this, except you will see a picture of the Time Capsule
Network Name..........Type in the exact name that the Netgear wireless is using
Base Station.............Type in a name that you want to call the Time Capsule. Use something short and simple. Mine is TC, for example
Password..................Type in the exact password that the Netgear wireless requires
Verify.........................Verify the Password again
Click Next
The setup wizard will configure everything for you automatically. When you see the message of Setup Complete, click Done.
That's it. Now you have one big "extended" network. Technically, this is called a "roaming" network.

Problems wirelessly extending 5Ghz network with Time Capsule

Summary:
My Time Capsule wirelessly extends a 5Ghz "n" network provided by my Airport Extreme, but the Time Capsule frequently fails and stops providing Internet access to connected computers. I'm not sure if the problem is with the Time Capsule or with the Airport Extreme it's connecting to.
Setup:
Airport Extreme (dual band) connected to cable modem. It provides a 5Ghz "n" network and a 2.5Ghz "b-g-n" network. This is in the bedroom.
Time Capsule (non-dual band) joins the 5Ghz network and extends it. This is in the office, maybe 40 feet away, line-of-sight. There is a laser printer connected to the Time Capsule via ethernet.
My MacBook is set to join the 5 Ghz network, and since it's in the office, it ends up joining via the Time Capsule. This is the desired behavior, as connecting through the Time Capsule seems to result in the fastest possible backup speed.
There are no wireless devices, such as cordless phones, in the house. The microwave is NOT in use when the problems arise.
*The Problem:*
Frequently, the MacBook loses its Internet connection, though it is still connected to the 5Ghz network through the Time Capsule. When this happens, it can only see the Time Capsule it's connected through (and other devices that are connected to it) but no other devices on the network.
When this happens, other devices that are connecting to the 5Ghz network through the Airport Extreme can no longer see the Time Capsule or any devices connected to it, such as the laser printer or my MacBook. This includes the living room computer, which has never been able to complete a backup due to this problem.
The Time Capsule's and the Airport Extreme's indicator lights both stay green.
If I change the Macbook's connection to the 2.5Ghz network, it can see the devices connected to the Airport Extreme, but can no longer reach the Time Capsule.
*Unsuccessful Solutions:*
This was happening in a previous incarnation of the network, when I had a non-dual band Airport Extreme providing the main network, the Time Capsule connected via 5Ghz, and an Airport Express connected via ethernet to the Time Capsule to provide a b-g network.
I replaced the Airport Extreme with a new dual-band unit to simplify the setup, but it did not solve the problem.
Since the Time Capsule seemed to be the weak link in the network, I reported the problem and got the unit replaced, but the problem still persists.
I've reset both the Airport Extreme and the Time Capsule to their factory settings numerous times, and set them up again from scratch (no imported settings). I've gone in and made sure that there were no WDS settings leftover from the earlier configuration, as the 5Ghz network does not need it to extend itself.
*Plea for help:*
Is anyone else experiencing a similar problem?

Update
The other day, I modified the setup so that the Time Capsule doesn't extend the wireless network wirelessly, only through Ethernet (so the attached printer will work, but the computers will connect directly to the AEBS. The Time Capsule stayed connected long enough for me to do a full backup (125GB) from the downstairs computer.
I thought I had it "solved" (though extending the 5Ghz network would be preferable so the office computers can have faster backup speeds.)
But yesterday, I went to print to the Ethernet-attached printer, and it got only one page out before it disappeared off the network again, and the print job failed. I noticed it did it again, today.
So the problem is not tied to wirelessly extending the network.

Painfully slow wireless connection with Time Capsule

I have recently bought and changed over my home wireless to a Time Capsule 2TB, which I wanted for both the backup and the ease in home networking. I have set up the wireless network and since day one it has been painfully slow! I have created two wireless networks, one for 2.4GHz and the other for 5GHz. I have been reading all over the web and boards but to no avail. Any suggestions? I am about to give up on the time capsule completely! I couldn't even download my podcast tonight.
Help!

Firstly plug in directly by ethernet to be sure there isn't a network issue on wan side.
Are you testing on multiple computers .. Mac and/or PC?? Which ones. and what network cards are being used?
Try and remove anything that uses G wireless and throw away any B wireless. It will not work together with N even if it is an option.
Turn off the guest network if you have it on.
Have you used a wireless analyser like kismac or inssider for pc? Find the free channels and set the wireless to that. Use no security at first to test.. briefly.. and then select wpa2 personal. Is there any difference?
Do you have another wireless router running?? Were you using a different wireless router for comparison?

Problem w/ wireless range with Time Capsule

Recently set up Time Capsule to swap out my Airport next to my Imac. Also have an Airport Express set up in another room to help extend wireless range. Found now that the range with Time Capsule is not as good as the Airport setup and I can't use my Ipad in the bedrooms furthest away from the Time Capsule. I'm not very tech saavy but would appreciate any suggestions? Thx.

When you set up TimeCapsule did you create a closed network? With a closed network, airport doesn't broadcast the network name, you have to manually enter it to join. This might be your problem. To fix it (or to see if that's what you've done) run Airport Utility and select manual setup. Select the Wireless tab and then click on the Wireless Options button at the bottom of the window.

Running a network with Time Capsule and Netgear router - is it possible?

We have an iMac and a Toshiba laptop. I was wondering if it was possible to have a wireless network with a Time Capsule and our Netgear DG834G router. We live in a solid brick house and the Netgear router is upstairs and we find we get very little, if any reception from downstairs. We have just purchased the Time Capsule and we were hoping to move the Netgear downstairs and have the Time Capsule upstairs to get reception all over the house. Is running a network like this possible, and if it is, how do we do it. Both the iMac and the laptop need to be able to connect. Thanks in advance.

g'day
you could try a pair of those http://www.amazon.co.uk/Devolo-MicroLink-dLAN-Highspeed-Starter/dp/B000A7IE7Y
see if this thread can help you in your planning http://discussions.apple.com/message.jspa?messageID=10430294#10430294

Wireless printing with time capsule 1tb and new wireless all in one printer

I am having problems with printing wirelessly from my time capsule 1tb. I currently have a hp 5510v office all in one printer and drivers can not be found to support printing wirelessly however it can print via usb. What I need is help in picking out a new all in one printer that can print wirelessly from time capsule 1tb. Please help

Hi,
my hp photosmart C6180 all in one works flawlessly with it plugged in to my time capsule all functions.
I used to have it set up using it wirelessly from the printer however for some reason after a update (i think) it stopped working & would not print so had to plug in to time capsule.
Dave

IPad2 in network with Time Capsule

will i be able to use the time capsule for a iPad as a external memory and transfer file from one to the other?

No, the iPad only connects to the internet sharing option of your network router (Time Capsule) through wifi. All other features of your router can't be accessed by your iPad. I have both also, so it would be nice. Try making that suggestion to Apple in the support section of the website. Who knows? We might get lucky. If this answer is satisfactory, please consider marking it as answering your question.
Thanks

Creating wireless network with Time Capsule

Similar Messages

Maybe you are looking for