Creative Sound Blaster Audigy ZS And Vista Driver installation prob

HI!
I encounter Installation problems with that file:
Creative Sound Blaster Audigy Value/SE/LS and Sound Blaster Li've! 24-bit XP and Windows Vista Pack .04.0077
I Use Vista 64Bit Ultimate and when I try to install this package I have an error message after my language selection. Is there a known issue for this
Thanks!
Julien

estebandit wrote:
Is there a known issue for this
Yes it is called trying to install the wrong driver for your card. Will work much better if you try installing the correct one,
SBAX_PCDRV_LB_2_8_000.exe
Also helps if you click on the "Show Details" link on the download page, then you would see that the one you tried to install doesn't support your card,
Requirements:
Microsoft Windows Vista 64-bit, Windows Vista 32-bit, Windows XP Professional x64 Edition, Windows XP Service Pack 2, Windows XP Media Center Edition 2005 or Windows XP Media Center Edition 2004
Sound Blaster Audigy Value/SE/LS, or Sound Blaster Li've! 24-bit audio devices
whereas the correct driver shows the following,
This download supports the following audio devices only:
Creative Sound Blaster Audigy including Platinum and Platinum eX series
Creative Sound Blaster Audigy 2 including Platinum, Platinum eX, and Value series
Creative Sound Blaster Audigy 2 ZS including Platinum and Platinum Pro series
Creative Sound Blaster Audigy 4 Pro and Sound Blaster Audigy 4
Creative Sound Blaster Audigy 2 ZS Notebook PCMCIA

Similar Messages

SOUND BLASTER AUDIGY SE AND VISTA DRIVERS WITH FULL FUNCTIONALITY- WOOOOO

(ONLY DRAWBACK IS THAT YOULL HAVE TO FIND ANOTHER MEDIA PLAYER BESIDES WINDOWS MEDIA PLAYER FOR YOUR SAVED AUDIO FILES: I WENT WITH WINAMP)
CONTINUE ON-
Download RAR file with ISO inside and install if you don't have the installation CD
installation cd with EQ download: http://files.filefront.com//;689430;;/
If you do or after you finish downloading goto step A.
A) Take your Creative Driver/Install CD, copy it to your hard dri've.
B) Goto Setup.exe right click, goto properties, goto the Compatibility tab.
C) Set it for Windows XP SP2.
D) Run install the Creative Audigy and if you need MediaSource *WMP Will pop and hiss while multitasking I reccomend MediaSource as it does not although the "Sources" is glitchy.
E) Restart when told to
F) Part ) Right click on the speaker icon by the clock, click Audio Devices... Right Click on Playback Control, goto properties click Configuration Set it to Stereo hit apply.
F) Part 2) Goto Speaker Settings, Set the configuration to 5./7. depending on what you need, then make sure Sync with Control Panel is UNCHECKED I found that is the critical element! Enjoy your multichannel!
G) Part ) Right click on the speaker icon by the clock, click Audio Devices... Right Click on Playback Control, goto properties click Configuration Set it to Stereo hit apply.
G) Part 2) Goto Speaker Settings, Set the configuration to 5./7. depending on what you need, then make sure Sync with Control Panel is UNCHECKED I found that is the critical element! Enjoy your multichannel!Message Edited by jeepbme on 03-08-200708:49 PM
Message Edited by jeepbme on 03-08-200708:50 PM

estebandit wrote:
Is there a known issue for this
Yes it is called trying to install the wrong driver for your card. Will work much better if you try installing the correct one,
SBAX_PCDRV_LB_2_8_000.exe
Also helps if you click on the "Show Details" link on the download page, then you would see that the one you tried to install doesn't support your card,
Requirements:
Microsoft Windows Vista 64-bit, Windows Vista 32-bit, Windows XP Professional x64 Edition, Windows XP Service Pack 2, Windows XP Media Center Edition 2005 or Windows XP Media Center Edition 2004
Sound Blaster Audigy Value/SE/LS, or Sound Blaster Li've! 24-bit audio devices
whereas the correct driver shows the following,
This download supports the following audio devices only:
Creative Sound Blaster Audigy including Platinum and Platinum eX series
Creative Sound Blaster Audigy 2 including Platinum, Platinum eX, and Value series
Creative Sound Blaster Audigy 2 ZS including Platinum and Platinum Pro series
Creative Sound Blaster Audigy 4 Pro and Sound Blaster Audigy 4
Creative Sound Blaster Audigy 2 ZS Notebook PCMCIA

Creative Sound Blaster Audigy Value/SE/LS Driver 01.04.0

Creative Sound Blaster Audigy Value/SE/LS and Sound Blaster Li've! 24-bit Vista Beta Driver 0.04.0055
Yeah, 32-bit, wooo.
When will a 64-bit version be available?

Has anyone tried the "AMD64" Driver for the Audigy Value (I assume this is the SE?) that is on the bundled CD?
I tried different driversets from the download/support site to no avail.
I didn't think about the CD driver until I got to work this morning.
Really wishing I picked up the Li've! (yesterday) instead of the Audigy Value now
...expected this card to have a better chance, especially with "x64 drivers" on the box.
Oh well, I'll give it one more shot tonight with those CD drivers... hopefully something will work.Message Edited by abz on 2-07-200604:08 PM

Creative Sound Blaster Audigy LS and soundfo

Hi! i got an Audigy LS, is it possible to use soundfonts with Cubase For example?
i didn't notice any instrument lik synt A or B like Sbli've did.
T. I.A.
Massimo

I'm not completely sure of the answer, but the Audigy LS specs have both wavetable synthesis and soundfont support listed. That indicates to me that it should be possible.
-Dave
[email protected]

Creative Sound Blaster Audigy 2 ZS Video Editor

Creative Sound Blaster Audigy? 2 ZS Video Editorc Hello.
I've recently changed from WinXP Pro SP3 x86 to Win7 Ultimate x64.
After installing the only available driver [Beta .0.0098] and rebooting, the Device Manager still lists an Unknown Device which corresponds to the video part.
<img border="0"><a rel="nofollow" target="_blank" href="http://img38.imageshack.us/img38/8/videoeditorprob.jpg"]http://img38.imageshack.us/img38/8/videoeditorprob.jpg[/url]
In Windows XP there were always two devices listed:
- SB Audigy 2 ZS Video Editor Audio Device;
- SB Audigy 2 ZS Video Editor Video Device.
I've tried to do the steps mentioned here <a rel="nofollow" target="_blank" href="http://forums.creative.com/t5/Windows-Vista/WILL-YOU-SUPPORT-THE-AUDIGY-2-ZS-VIDEO-EDITOR-IN-VISTA/m-p/3602"]http://forums.creative.com/t5/Windows-Vista/WILL-YOU-SUPPORT-THE-AUDIGY-2-ZS-VIDEO-EDITOR-IN-VISTA/m-p/3602[/url] with both old and more recent XP/Vista 32/64 drivers and I still can't get the device installed and VidCap properly running.
Thanks in advance.

Hello,
I have the exact same problem and would very much like to know if there are 64bit drivers available.
Thanks in advance.

Creative Sound Blaster Audigy SE, 7.1 surround?

What are the latest drivers for Creative Sound Blaster Audigy SE, 7.1 surround? I have have tried a lot of drivers and they don t seem to work...

I have a Sound Blaster Audigy SE on Windows Vista Home Premium 32-bit operating system. So far this Gateway GT5404 duo core pc is having better audio capabilities with high end games like world of warcraft, with some noticable sound issues (Sigmatel audio). I bought this card to better the audio performance of World of Warcraft and get rid of these issues. I'm not sure if this card is any better than the on-board intergrated sound card on this gateway. Is this just a driver issue with the Audigy SE card? or is my on-board better? After putting it in world of warcraft's sound on the logon screen and throughout the game sound "stretched" from lag from the video card's high end performance (NVidia GeForce 7600 w/latest drivers). Any help or info would really do me good right now. Thanks,?PurePower

Creative Sound Blaster Audigy SE problems

Alright first of all I am new to Linux in general.
I have two soundcards in my computer. One is an onboard card (Intel) that is faulty and doesn't work; another is a Creative Sound Blaster Audigy SE which does work.
My problem, of course, is getting the latter to work.
So I realize this is nothing new, searching the forums and reading ALSA's wiki. However there seems to be some issues with making this work on ALSA, so is there a way to configure this with OSS?
"lspci | grep audio" returns both soundcards:
00:1f.5 Multimedia audio controller: Intel Corporation 82801EB/ER (ICH5/ICH5R) AC'97 Audio Controller (rev 02)
01:00.0 Multimedia audio controller: Creative Labs CA0106 Soundblaster
"ossdetect -v" returns:
Detected Sound Blaster Audigy LS / Live7.1
Detected Intel AC97 (ICH5)
USB support available in the system, adding USB driver
Detected Generic USB audio/MIDI device (BETA)
I use "soundoff" and "soundon", then "osstest":
Sound subsystem and version: OSS 4.1 (b 1052/200903241101) (0x00040100)
Platform: Linux/i686 2.6.29-ARCH #1 SMP PREEMPT Wed Apr 8 12:47:56 UTC 2009
*** Scanning sound adapter #-1 ***
/dev/oss/oss_audigyls0/pcm0 (audio engine 0): AudigyLS front
- Performing audio playback test...
<left> Device returned error: Input/output error
/dev/oss/oss_audigyls0/pcm1 (audio engine 2): AudigyLS center/lfe
- Performing audio playback test...
<left> Device returned error: Input/output error
/dev/oss/oss_audigyls0/pcm2 (audio engine 3): AudigyLS surround
- Performing audio playback test...
<left> Device returned error: Input/output error
/dev/oss/oss_audigyls0/pcm3 (audio engine 4): AudigyLS 5.1 output
- Skipping multi channel device
*** Scanning sound adapter #1 ***
/dev/oss/oss_ich0/pcm0 (audio engine 9): Intel ICH5 (24D5)
- Performing audio playback test...
<left> OK <right> OK <stereo> OK <measured srate 47982.00 Hz (-0.04%)>
*** Some errors were detected during the tests ***
Basically it seems like it detects the crappy onboard sound (which is unusable, I stress) and not my soundcard. I really don't know how to fix/configure this and sound is really important to me if I'll be using Arch.
Thanks for any help offered, if more information about something is needed I'll be more than happy to oblige.

I would start by disabling the on board sound in your BIOS if you are not going to use it. As a novice user much of the documentation kind of covers the simpler case and this might help you navigate them better.
Keep in mind the Audigy SE is not a real Audigy (like Audigy 2 which has very good linux support). If you are just looking for straightforward playback you should have no trouble, but you will not get hardware mixing with SE IIRC.

Creative Sound Blaster Audigy SE SBO570 Can't play 5.1 HELP

Hey
- Using Windows 7 & 32 bit
I Have Creative Sound Blaster Audigy SE?SBO570, and i use Creative Audio Control Panel.
I have set it to 5. in Creative Audio Control Panel but it play only like 2.
before i installed my new windows 7 it worked fine.. and i used "Creative Volume Panel for 5." and testing speakers there.. but now i can't.. i think i need software for windows 7. I have it newest Driver for windows 7.
i been looked everywhere for some software but i get error everytime :S
PLEASE HELP ME! :S
Sorry for my bad english.

btw everytime i trying install it from CD i getting Crash Dump in blue screen and restarting.. and then i starting again i getting error:
The audio device supported by this application is not detected. The application will exit

Pin Specifications for Creative Sound Blaster Audigy SB1394

;Pin Specifications for Creative Sound Blaster Audigy SB394 I have a Sound Blaster Audigy SB934 CA000-IAF Creative Tech '0 AA299J basically a Sound Blaster Audigy Platinum (wiouth the front bay for conectivity.)? And since I dont' have the front bay for heaphone and mic conectivity I was wondering if there is a spec sheet for the 40-Pin conectivity that is used for the front bay. I was wondering if anyone could provide me with such spec sheet so that I can try to conect my frontal Intel board plugs for headphone and microphone (would like to use my headset.)
There are a lot of pins on the card and well only about 8 in the conector for the front plugs. So if any dev from the forum is reading this I would greatly apreciate it if I could use my front Intel sound plugs on this old model card.
Thank you for all your help.

http://www.driverheaven.net/audio-general-technical-discussion/5279-creative-audigy-2-ad_ext-pin-assignment.html
That will help you with the pin assignments.......
And you can also try one of these to connect a lot more easily to your front panel audio jacks.......
www.x-tap.com
I used the above with four Audigy LS and SE's and it works a treat!

Is Creative Sound Blaster Audigy 2 NX USB sound card compatible with Dell deskt

Im considering buying the Creative Sound Blaster Audigy 2 NX USB sound card to use with a Dell desktop XPS 40, but recently read a forum message on another page that there was a issue with installing on a Dell Tower but no problems with installing on a laptop
any help is appreciated if there are any compatibility issues with using this sound card on a Dell desktop, Thanks
the main reason I would like to upgrade to this card is so my pc doesnt use the integrated audio which Id like better quality performance with a sound card and also dont want to install a internal card on the system

joaolfb,
Audigy 2 NX will need to be connected with the power adaptor inorder to run. USB will not be enough to sustain the power consumption of the sound card.
Jason

Creative Sound Blaster Audigy 2 B4

Ok so as listed above, my current soundcard is a Creative Sound Blaster Audigy 2 B400, now when you google that the card doesnt come up unless its a ZS? My card is NOT a ZS though, its exactly as stated. Anyway, since its almost impossible to find I HAVE found a picture of the back of the card:
http://mayhem.prod.googlepages.com/p...inout-full.jpg
Now on to my question. I'm looking to buy?the Logitech Z-5500 5. surround sound (Digital) for my computer, now, I want to be sure that this card can support two things.
) The digital input itself, my card has a white "Digital" input, so obviously my first guess is yes.
2) This cable: http://www.monstercable.com/productdisplay.asp?pin=600
And if it can support that cable, will it benefit me? Sorry for the trouble, I just dont want to spend the money and not be able to support it. Thanks for the help.

Kenttheman wrote:
Ok so as listed above, my current soundcard is a Creative Sound Blaster Audigy 2 B400, now when you google that the card doesnt come up unless its a ZS? My card is NOT a ZS though, its exactly as stated. Anyway, since its almost impossible to find I HAVE found a picture of the back of the card:
http://mayhem.prod.googlepages.com/p...inout-full.jpg
Now on to my question. I'm looking to buy the Logitech Z-5500 5. surround sound (Digital) for my computer, now, I want to be sure that this card can support two things.
) The digital input itself, my card has a white "Digital" input, so obviously my first guess is yes.
2) This cable: http://www.monstercable.com/productdisplay.asp?pin=600
And if it can support that cable, will it benefit me? Sorry for the trouble, I just dont want to spend the money and not be able to support it. Thanks for the help.
By the Creative audio product database, SB0400 = Sound Blaster Audigy 2 Value. You'll find the User's Guide through Support->Product Documentation ... ther're diagrams for connectivity in guide. It's possible you need [url="http://us.creative.com/products/product.asp?category=&subcategory=6&product=780">t his[/url] addon for S/PDIF connections.
jutapa
Message Edited by jutapa on 04-27-2008 04:2 PM

Creative sound blaster audigy 2 zs h

I have creative sound blaster audigy 2 zs card and a set of AV labs, amped 7. sound system speakers. i have 4 input wires to plug into the card and it only seems to have 3 output jacks. When i go and calibrate the speakers i am missing out on my two surround speakers. how should i be hooking these up. There is probaly a simple ansew to this but it has me stumped. help please

Please read Creative's speaker connectivity guide: <A href="]http://ask.americas.creative.com/SRVS/CGI-BIN/WEBCGI.EXE/,/?St=787,E=0000000000070303557,K=54,Sxi=0,Question3 895=obj(3895): obj(3899))[/url] (Remove the space between ": obj", I wrote so cause I get a smiley otherwise:angry: )
As you will see in the article, the Audigy is fitted with two 4-pole connectors, which can carry 3-channels each. So you only need 3 wires for a 7. system, as you have 2 normal stereo plugs (3-pole) and 2 3-channel plugs (2*2+2*3=8). You will most probably need different wiring for your speaker system as it appears you have 4 stereo plugs.
Message Edited by alexs3d2 on <SPAN class=date_text>08-0-2005<SPAN class=time_text>:36 AM
Message Edited by alexs3d2 on <SPAN class=date_text>08-0-2005 <SPAN class=time_text>:37 AM
Message Edited by alexs3d2 on 08-0-2005 :39 AM

Creative Sound Blaster Audigy 2 ZS With WinTV Expr

Hi,
I am using a Creative Sound Blaster Audigy 2 ZS sound card, and I recently purchased a Hauppauge WinTV Express card, I have installed the card with no problems, but it says I have to connect a wire from the Line Out port on the WinTV card into the line In port on my sound card. I cannot find a line in port onm the back of my sound card so I am getting so sound from WinTV. Can anyone please tell me how to set it up correctly?
Thanks for your help,
MJJOS.

The Line In jack is the second jack from the Digital Out jack. If you have problem locating those jack, you can checkup the user guide too.
Jason

Help! Creative Sound Blaster Audigy SE 7.1 Sound Card -

Hello. I've just recieved my new soundcard. It is the Creative Sound Blaster Audigy SE 7. Sound Card - OEM. (Located here: http://www.overclockers.co.uk/showp...atid=&subcat=)
My motherboard is a Asus A8N SLi se.
Now, I have put it in my motherboard, and just tried to install the drivers. I got an error though. It said "No compatible creative product detected." So I downloaded the drivers off the Creative site, and that did not help either. I disabled the onboard sound in the BIOS, and yet it still did not work. I tried plugging in the soundcard into each of the soundcard ports on my motherboard, and none of them detected the card.
I am sick of using onboard, and would like to get this problem fixed.
Some additional information:
The back audio/microphone ports on my motherboard never worked. I have been using the front sockets on my case. I see cables running from my motherboard to the front of my case. Maybe one of those cables need to go into my soundcard in order for it to work? I'm not sure which though, so I didn't try it, just incase.
Here are some screenshots of what I'm getting. They might help.
Drivers from the Creative site: http://img409.imageshack.us/img409/4528/gayap9.jpg
Drivers from the Creative CD: http://img520.imageshack.us/img520/3649/gaycdam5.jpg
Unknown Device in my Device Manager: http://img409.imageshack.us/img409/9924/unknownoj8.jpg
Now, I have no other creative parts in my computer. So this should be the soundcard, right?
Thanks in advanced for any replies.

Does the cable from the MB to the front I/O panel simuliar to this one? I installed a Audigy2 ZS in my other system and connected the black cable with the 0 pin connector to the card to use my front phone/mike jacks. Also in your device manager I see the Realtek AC97 still listed. When I installed the XM card in my 600 I disabled it in the BIOS so the entry does not show up in mine just the SB XF-I is displayed.
src="http://i.pbase.com/g6/89/377389/2/79327975.pMK94KJy.jpg" alt="IMG_008.JPG">
Dell XPS 600 Intel Pent D 830 3.0ghz
Chipset- Nvidia nForce4 SLI Intel Edition
WD 60gb HD
2gb Ram
DVD-ROM
DVD-RW (Plextor 760A)
Creative XF-I Extreme Music
Logitech X-540 speakers
EVGA 7950GT
Dell 2007WFP (I-SPS panel)
Win XP SP2
BIOS A

Creative Sound Blaster Audigy Issues

$C? When playing music on my computer the sound skip's, stutters and pauses. I have these symptoms when playing aCD as well as MP3 files . I tried different players but all have the same result. I thought it was my Anti Virus, butwhen disabled it symptoms still occur. Onboard sound works perfectly. Sound card has worked fine the past threeyears until I re-installed windows recently. I have updated all drivers including Chipset and Sound card. Thinkingit may be an IRQ issue but I do not know where to begin. Is it just a bad sound card please help!
OS: Windows XP Professional
Processor: Processor 3.20 gigahertz Intel Celeron
RAM: 2048 MB
Hard Disk TB of which 5GB is used
Sound Card: Creative Sound Blaster Audigy-Model Number SB0570
Mother Borad: MICRO-STAR INTERNATIONAL CO? PM8M-V Socket 478 Motherboard

Oh my sweet Jesus Creative, what are you doing?!
This is just funny - I can't play MP3's in 5. mode! LOL!? You 'aving a bath!
On top of that you've rendered DDL useless because my spdif output doesn't appear in the drop down box.
Interestingly though I can MP3 in 5. fine through VLC player.
Have you added some kind of hardware MP3 decoding or something?
You know if you're trying to keep us with you, or encourage us to upgrade, you're going about it a very odd way.
Win 7 RC700, Audigy 2 OEM, http://forums.creative.com/i/smilies/6x6_smiley-wink.gif" title="Smiley Wink" alt="[/img]? I think you owe us now, tbh. Even just a little something like properly working CMSS 3D for headphones would be nice (which I believe is an X-Fi feature), or the ability to record 5. in WaveStudio. However I get the feeling that it would only cause more problems!? lol. http://forums.creative.com/i/smilies/6x6_smiley-wink.gif" title="Smiley Wink" alt="[/img]
Message Edited by Meocene on 07-7-2009 03:3 [email protected]

Creative Sound Blaster Audigy ZS And Vista Driver installation prob

Similar Messages

Maybe you are looking for