CS4 and Matrox MX02 Mini with MAX

CS4 sucks.
Is there some kind of written rule that eac new version has be worse than the previous ?
Why does Adobe keep cutting out the tools and processes we, I, want the most !
Examples;
WHY doe Adobe STILL refuse to put back in stop motion capture ?
Why has Adobe screwed up the whole export thing and made it not only 100 times more complicated, but, also able to do 100 times LESS than it always used to in previous versions ?
BUT, my immediate question is why are my 720x480i exports to MPEG2-DVD m2v repeatedly failing - unknown error ?
- Source File: C:\DOCUME~1\steve\LOCALS~1\Temp\fleming8mmfilms-sd-3_2.prproj
- Output File: C:\Sequence 01.m2v
- Preset Used: Custom
- Video: NTSC, 720x480, 29.97 drop frame [fps], Lower, Quality 5.0
- Audio: No Summary Available
- Bitrate: VBR, 1 Pass, Min 2.01, Target 4.13, Max 7.00 [Mbps]
- Encoding Time: 00:00:08
18/09/2009 9:35:55 PM : Encoding Failed
Error compiling movie.
Unknown error.

I didn't sin, but you did by assuming things that are not true.
1/ The project file is on the same drive as the export, BUT, the source files are on a different capture drive than the export to C.
2/ I've been using the Matrox RTX100 with previous versions of Premiere for 7 years, and the two have worked very well together all that time, and still are working very well, and, will continue to I've no doubt. - Just because you couldn't get it to work, does not mean they don't.
3/ The export I refer to did not have any connection to the Matrox box. All Premiere and Encore.
4/ I didn't mention that I had done a lot of successful export tests of various definition formats, to other formats, and including a 1 hour Full HD export, no problems.
So, - there - nyah !

Similar Messages

FCP 7 and Matrox MX02 mini has bad audio playback

This problem has been frustrating me for months.
I have FCP setup to output video and audio via my marox MX02 mini. The mini is hooked up to HDMI and component, and RCA audio.
When playing back on the timeline in FCP the audio stutters, echos and drops out.
I've been bugging them at the Matrox forum, and each new update that comes out claims to fix the problem, and it gets a little better, but honestly it is still nowhere near satisfactory.
It's worst when stepping 1 frame at a time or scrubbing thru footage.
Does anyone else experience this problem? Am I doing something wrong?

What drivers are you running? What footage type are you working with? Format, frame rate...
Thanks,
Shane

Speedgrade with Matrox MX02 Mini

Has anyone had success getting SG to display on an external monitor via Matrox MX02 Mini? PP, AE, even PS can output to the monitor via Matrox MX02, but not SG. If I delete the PluginCache64 folder in regedit, it will show up as a display option the next time I launch, but then if I close and relaunch SG, it's no longer an option. Matrox says it should work. Adobe support says it doesn't but maybe in the next version. Anyone got a fix? I am on Windows 7 64-bit. :atest Matrox driver (installed after CC).

Second display works on my MacPro with the Matrox MXO2 mini MAX driver supporting Mavericks and Adobe CC (ver 4.1). Only got external monitor with this recent driver release using current CC versions
Kuhnen

Matrox Mini with Max

Is anyone having problems with a Matrox Mini with Max with OSX10.8.1. mine just does not work.

I didn't sin, but you did by assuming things that are not true.
1/ The project file is on the same drive as the export, BUT, the source files are on a different capture drive than the export to C.
2/ I've been using the Matrox RTX100 with previous versions of Premiere for 7 years, and the two have worked very well together all that time, and still are working very well, and, will continue to I've no doubt. - Just because you couldn't get it to work, does not mean they don't.
3/ The export I refer to did not have any connection to the Matrox box. All Premiere and Encore.
4/ I didn't mention that I had done a lot of successful export tests of various definition formats, to other formats, and including a 1 hour Full HD export, no problems.
So, - there - nyah !

New Matrox MX02 mini not working

Just got a new Matrox MX02 Mini. I'v installed the PCIe card seemingly successfully - it's showing up in the system profiler under "Other Multimedia". I downloaded and installed the software package 2.0 from the Matrox site.
But when I go into Final Cut I get no option for Matrox under Video Playback. And no video or audio is playing through my Matrox (as far as I can tell).
I'm on a Mac Pro running 10.6.4 and Final Cut 6.0.6. Trying to go out from my Matrox HDMI to a Panasonic HD TV monitor and with audio going to external speakers.
Thanks for any help.
Seth

Just got my new MXO2 Mini MAX, and it won't even power up. The pci-e card does NOT show up in the System Profiler under PCI cards. I tried the card in two other slots, still not showing up as being seen by the MacPro (2009 Quad Intel). The card also did not show up when installed in our other MacPro (2007 Intel). All cable connections, including power are according to Hoyle. Should I be seeing a light come on inside the MXO2 mini box? As it is now, no light, no life.
I pre-installed the driver, and in System Prefs the Matrox MXO2 mini icon reports: "..video hardware not found." The Product Name, S/N, and Firmware Version are all blank lines. Software version is 2.0.0.
Thanks,
Mark.
Snow Leopard 10.6.5
FCP Studio 3
MacPro Quad (2009 Intel)

I have not been able to use iTunes for several months. Every time I open iTunes, it freezes by computer such that there is about a minutes between each action. I am running iTunes 11 on Mac OS 10.6.8 and have a computer with maxed out memory.

I have not been able to use iTunes for several months. Every time I open iTunes, it freezes by computer such that there is about a minutes between each action. I am running iTunes 11 on Mac OS 10.6.8 and have a computer with maxed out memory. Help! I can't access my iTunes content.

I have not been able to use iTunes for several months. Every time I open iTunes, it freezes by computer such that there is about a minutes between each action. I am running iTunes 11 on Mac OS 10.6.8 and have a computer with maxed out memory. Help! I can't access my iTunes content.

I have an ipod touch 4th gen and an ipad mini with same apple ID   and I want to sync the songs

I have an ipod touch 4th gen and an ipad mini with same apple ID   and I want to sync the songs

Just connect to computer and sync.
iTunes: Syncing media content to iOS devices and iPod
Try syncing using the manual method to more easily get different media on each device
Managing content manually on iPhone, iPad, and iPod

I own a MacBook Pro laptop, an iPhone5 and an iPad mini with an itunes/apple account. I just added an iphone5 for my wife. What is the best way to sync shared music, ical, etc.?

I own a MacBook Pro laptop, an iPhone5 and an iPad mini with an itunes and apple account. I just purchased another iphone5 for my wife. What is the best way to sync and share iTunes music, iCal dates on her phone and my computer and devices? We don't need to sync and share contacts.

Jordans374 wrote:
Both are already synced to a windows laptop?
Move iTunes Library from PC to MAC
http://www.macworld.com/article/146958/2010/03/move_itunes_windows_mac.html

I have a Power Mac G5 - How can I run Matrox MX02 mini max

I have a Power Mac G5 Running Mac OSX 10.5.8 I recently got the MX02 Mini Max by Matrox to run my Final Cut Studio application version 6.6 and Im having problems with the pci board that comes with the matrox unit ( it does not fit in the mother board) how would i be able to use this with out connecting the pci board into my mother board on my Mac.?

Can't use it with a G5.
System requirements are Mac Pro and Intel-based MacBook Pro running Mac OS X Leopard 10.5.6 or higher.
IF (big if) the card is PPC Mac compatible, only Late 2005 G5 machines have PCIe. All other G5s are PCI.
The Matrox card is PCIe, not PCI.

Matrox MX02 Mini and FCP 7...

We have been using the MX02 Mini essentially for HD monitoring and have run across a few issues that have hindered productivity. It appears that one or two of these issues have been fixed in the latest 2.2.1 software release. The following remain. Has anyone experienced the same?
1) Audio scrubbing... audio cannot be heard on a per frame basis, usually audio is heard every three
frames or so.
Apparently this has not been fixed.
2) Audio playback. In the viewer... Hit play... Playback begins but the audio drops out and then
resumes... hit stop and playback repeats the last bit of what was playing before you hit stop.
3) Audio distorts, similar to an analog overdrive sound, when hitting play every 10 times or so.
Most of the projects that we are working with are Apple Pro Res 422 @ 23.98, Audio 48khz/16 bits.
Most of our computers are as described... 2 x 2.26GHz Quad Core Mac Pro running 10.6.6 and FCP 7.0.3.
Hard drives are local external 2TB G-RAIDs with plenty of room. We have check all of our media to make sure that it matches our sequence settings.
I realize that there are Matrox advocates out there, but we seem to have a hard time getting the MX02 Minis to work reliably.
All ideas are welcome. Note that we are working with Matrox support as well.
Thanks,
Scott

1) Audio scrubbing... audio cannot be heard on a per frame basis, usually audio is heard every three frames or so. Apparently this has not been fixed.
Well, that actually is the main thing that was addressed in that update. I didn't have the issue for a while, then I upgraded to snow leopard, and there it was. But that was something with the 2.0 and first 2.1 drivers. But the latest driver that was just released, 2.1.1...fixes that. For a lot of people, me included:
http://forums.creativecow.net/thread/132/860478
http://forums.creativecow.net/thread/132/860397
As for the other issues, that are all audio related... they should have been addressed too.
Make sure to update PROPERLY. Uninstall the older drivers, then restart. Install the new drivers... and when the updates erase and then update the firmware, when the computer will shut down, and you need to unplug the MXO2 mini for at least 5 seconds, then plug it back in. Then start up the system.
Shane

Export from CS4 to Matrox MX02 LE to Betacam deck

Hi,
I'm attempting to export a sequence to tape. I think I have all my inputs and outputs set up right but I can't seem to record my sequence onto tape. I have no problem capturing footage from tape but going the other way won't seem to work. I have a Matrox MX02 LE connected to a Sony Betacam deck. Not even sure where to start as far as diagnosing this problem. Any ideas?
Thanks,
Kevin

Well, the first thing is to confirm that you're getting a signal out of the s-video port on the MXO. Plug it directly into a monitor to confirm a signal. If that's not working, it's probably a Matrox MXO panel option or something similar (i vaguely remember in the past that you had to choose between s-video or component out, although that might be not required anymore). If you are getting a signal out, then it's likely a deck setting somewhere.
One thing that trips people up with betacams is that there's an EE mode that allows passthrough so that, if you're monitoring the output of the deck, it'll pass through the input. If that's off (ie PB mode), you'll only see black when you put the deck in record mode.

Color 1.5 and Matrox MXO2 Mini

Hey all. Just got the MXO2 Mini from Matrox which is really amazing. I use Apple, Adobe and Avid products so when Avid announced that this would be the device they will be compatible with I jumped on getting one. It works amazingly well in every product I've tested, Premiere, FCP, Compressor (for h.264 Max encodes), After Effects and so on. But I get into Apple Color and an odd thing happens, it plays the video I bring in in the little preview window on my second monitor but it old shows me a still of the frame I park on on my preview monitor. The codec is obviously working to an extent since the options for preview showed up in Color and that I saw picture when I selected it. But is the preview monitor only showing a still frame right or normal? Anyways thanks for any insight.

I disagree with nothing you've said. I already know Davinci having piloted a few sessions (though it's not my primary work by far) and I took to it much quicker than I took to Color. Though I have no issues with the learning curve on Color either. I think they are both great with equally good and bad support for 3rd party hardware. But I do think that Davinci is a more worth while product to use if you want to compete in the color correction profession.
The thing that bothers me about Apple's Final Cut Studio in the past 2 versions is that both stability and innovation seems to have stopped. Dvd Studio Pro has gotten no love for what 4 versions now? They push Quicktime as the core video technology behind all of their apps like FCP and Color yet when they've had ample time to modify Color's code to reflect their software compatibility needs things like the hardware issue I'm having pop up ONLY in Color. Just seems like Apple just wants to buy good apps, sell them in a bundle as inexpensive as they can to sell systems but they've lost their competitive edge with comparable NLE packages like Adobe's Production Suite CS5 or Avid MC. Not to mention they've done nothing to compete in the pro space with the advancements Avid makes every version. Not including the features coming in MC5, MC4s AMA already makes it faster to get editing than FCP was ever able to do. Plus, much like our Color VS Davnici conversation, if you learn Avid you learn software EVERY post house in the world has and uses. The workflows are standards. FCP doesn't have great workflow infrastructure and Apple doesn't seem interested in fixing that.
Why did I just go on that rant? Well I guess it's because I have to use these tools daily and though I see so much potential in Apple Color alone, I feel issues like the one I'm having right now show a serious lack in Apple's interest in keeping their software suite competitive and stable.

MATROX MX02 mini on NTSC monitor

hi, i just bought this product and it is a bear to set up. tech support closed. i am hoping someone out there with this unit might be able to help.
i am trying to connect it to my Sony PVM broadcast monitor, which is SD. i am going RGB out on mini via monster cables to RGB component in on the NTSC monitor (which has BNC connectors, but i have RCA adapters. I am using the NTSC setup in Final Cut. Nothing on screen. Can anyone help me?

There is a large list of flavors to play out when you chose Matrox in FCP in the playback tab - in that giant list, you have to match whatever your playing to. So, in your case, set it to NTSC. It doesn't actually say "down convert".
pJ

SG 2014 w/Matrox MX02 Mini - audio glitch

With previous version, I could not get SG to display on my external monitor via Matrox - at all. It was not an option. Now with 2014 and the latest Matrox driver, I can output through the Matrox, but the audio is choppy. As if it has latency issues. I've tried changing the settings under "display" and "audio" but to no avail. Anyone else using this combination? If so, does it work for you? I have no issues with the same setup, same computer and PP, AE, or Avid MC.

Thanks for the reply penguin!
I tried adding it to the kernel, but it did not work. I think usb_hid is just for usb keyboards/mouses/etc.
I noticed that every time I remove and plugin my flash drive /var/log/messages.log says something slightly different for my flash drive if that helps:
Oct 30 18:10:43 myhost sda1
Oct 30 18:10:43 myhost Attached scsi removable disk sda at scsi4, channel 0, id
Oct 30 18:10:43 myhost Attached scsi generic sg0 at scsi4, channel 0, id 0, lun
Oct 30 18:11:10 myhost (jftaylor21-896): starting (version 2.12.0), pid 896 user
Oct 30 18:11:10 myhost (jftaylor21-896): Resolved address "xml:readonly:/opt/gnosition 0
Oct 30 18:11:10 myhost (jftaylor21-896): Resolved address "xml:readwrite:/home/j
Oct 30 18:11:10 myhost (jftaylor21-896): Resolved address "xml:readonly:/opt/gnoition 2
Oct 30 18:11:50 myhost usb 1-6: USB disconnect, address 3
Oct 30 18:11:55 myhost usb 1-6: new high speed USB device using ehci_hcd and add
Oct 30 18:11:55 myhost scsi5 : SCSI emulation for USB Mass Storage devices
Any other suggestions?

Having problems configuring and testing FieldPoint modules with MAX 3.0.

I have a FP-1000 and FP-AO-200 connected together. MAX is able to find the FP-1000 and communicate with it. The FP-AO-200 POWER and READY lights are on.
MAX does not find the FP-AO-200 when I invoke "Find Devices". I can manually define it using "Create New Device". When I attempt to test a FP-AO-200 channel using the Write function in "Items Configuration" I get the following error message: "The module or item addressed does not exist".
I am also not able to write to any FP-AO-200 channels in LabVIEW 7.0.
Any ideas what is wrong?

I would check the pins on the FP-1000, between the modules for bent or pushed in pins. Then, I would make sure the AO module is seated correctly in the Terminal Base.
If that's not it, try a different AO module and/or a different TB, to see which is the culprit. The AO module should show up when you do "Find Devices".

CS4 and Matrox MX02 Mini with MAX

Similar Messages

Maybe you are looking for