CVP 7.0.2 Abnormally disconnected with error code 38

Hi all,
We have an issue where when called from outbound, it is not possible to reach a certain number. It doesn't even play the dial tone. isdn debug is as follows :
Feb 15 17:51:01.830: ISDN Se0/2/0:15 Q931: TX -> RELEASE pd = 8  callref = 0xE97B
Feb 15 17:51:01.846: ISDN Se0/2/0:15 Q931: RX <- RELEASE_COMP pd = 8  callref = 0x697B
Feb 15 17:51:05.050: ISDN Se0/2/0:15 Q931: RX <- SETUP pd = 8  callref = 0x697D
        Sending Complete
        Bearer Capability i = 0x8090A3
                Standard = CCITT
                Transfer Capability = Speech 
                Transfer Mode = Circuit
                Transfer Rate = 64 kbit/s
        Channel ID i = 0xA98385
                Exclusive, Channel 5
        Progress Ind i = 0x8083 - Origination address is non-ISDN 
        Progress Ind i = 0x8A81 - Call not end-to-end ISDN, may have in-band info 
        Calling Party Number i = 0x0081, '02124783464'
                Plan:Unknown, Type:Unknown
        Called Party Number i = 0xC1, '2751920'
                Plan:ISDN, Type:Subscriber(local)
Feb 15 17:51:05.062: ISDN Se0/2/0:15 Q931: TX -> CALL_PROC pd = 8  callref = 0xE97D
        Channel ID i = 0xA98385
                Exclusive, Channel 5
Feb 15 17:51:05.066: %HTTPC-6-REQUEST_FAILED: request URI http://ipphone.fw.garanti.com.tr/ipphone/musteribilgiler?source=TLC&call_data=002124783464-800321200 failed
Feb 15 17:51:05.066: %IVR-3-APP_ERR: Musteri bilgileri serverdan alinamadi - Hata Kodu: error
Feb 15 17:51:05.210: %HTTPC-6-REQUEST_FAILED: request URI http://10.231.51.141:8000/cvp/VBServlet?MSG_TYPE=PING&CALL_DNIS=2403519900&CALL_ANI=sip:[email protected]:5060&ERROR_CODE=0&RECOVERY_VXML=flash:recovery.vxml&CLIENT_TYPE=IOS&CALL_ID=DE8929A61000013C1771025A0AE7338D&SIP_CALL_ID=[email protected]&CALL_UUI=&VERSION=7.0.2 failed
Feb 15 17:51:05.226: %HTTPC-6-REQUEST_FAILED: request URI http://10.231.51.141:8000/cvp/VBServlet?MSG_TYPE=PING&CALL_DNIS=2403519900&CALL_ANI=sip:[email protected]:5060&ERROR_CODE=0&RECOVERY_VXML=flash:recovery.vxml&CLIENT_TYPE=IOS&CALL_ID=DE8929A61000013C1771025A0AE7338D&SIP_CALL_ID=[email protected]&CALL_UUI=&VERSION=7.0.2 failed
Feb 15 17:51:05.230: %HTTPC-6-REQUEST_FAILED: request URI http://10.231.51.141:8000/cvp/VBServlet?MSG_TYPE=PING&CALL_DNIS=2403519900&CALL_ANI=sip:[email protected]:5060&ERROR_CODE=0&RECOVERY_VXML=flash:recovery.vxml&CLIENT_TYPE=IOS&CALL_ID=DE8929A61000013C1771025A0AE7338D&SIP_CALL_ID=[email protected]&CALL_UUI=&VERSION=7.0.2 failed
Feb 15 17:51:05.238: %HTTPC-6-REQUEST_FAILED: request URI http://10.231.51.141:8000/cvp/VBServlet?MSG_TYPE=PING&CALL_DNIS=2403519900&CALL_ANI=sip:[email protected]:5060&ERROR_CODE=0&RECOVERY_VXML=flash:recovery.vxml&CLIENT_TYPE=IOS&CALL_ID=DE8929A61000013C1771025A0AE7338D&SIP_CALL_ID=[email protected]&CALL_UUI=&VERSION=7.0.2 failed
Feb 15 17:51:05.246: %IVR-3-APP_ERR:
**** CVP HANDOFF.TCL: 57080581.76BE11E2.A32B001B.D5293620 abnormally disconnected with code 38. ****
Feb 15 17:51:05.258: ISDN Se0/2/0:15 Q931: TX -> CONNECT pd = 8  callref = 0xE97D
Feb 15 17:51:05.290: ISDN Se0/2/0:15 Q931: RX <- CONNECT_ACK pd = 8  callref = 0x697D
Feb 15 17:51:05.294: %ISDN-6-CONNECT: Interface Serial0/2/0:4 is now connected to 02124783464 N/A
Feb 15 17:51:07.274: %IVR-3-APP_ERR:  ani: 002124783464 dnis: 800321200 | ev_setup_done ls_000 | ev_disconnected di_016 |
Feb 15 17:51:07.298: %ISDN-6-CONNECT: Interface Serial0/2/0:4 is now connected to 02124783464 N/A
Feb 15 17:51:07.298: %ISDN-6-DISCONNECT: Interface Serial0/2/0:4  disconnected from 02124783464 , call lasted 2 seconds
Feb 15 17:51:07.302: ISDN Se0/2/0:15 Q931: TX -> DISCONNECT pd = 8  callref = 0xE97D
        Cause i = 0x8090 - Normal call clearing
Feb 15 17:51:07.362: ISDN Se0/2/0:15 Q931: RX <- RELEASE pd = 8  callref = 0x697D
Feb 15 17:51:07.366: ISDN Se0/2/0:15 Q931: TX -> RELEASE_COMP pd = 8  callref = 0xE97D
Feb 15 17:51:08.702: ISDN Se0/2/0:15 Q931: RX <- SETUP pd = 8  callref = 0x697E
        Sending Complete
        Bearer Capability i = 0x8090A3
                Standard = CCITT
                Transfer Capability = Speech 
                Transfer Mode = Circuit
                Transfer Rate = 64 kbit/s
        Channel ID i = 0xA98391
                Exclusive, Channel 17
        Calling Party Number i = 0x0083, '05336805920'
                Plan:Unknown, Type:Unknown
        Called Party Number i = 0xC1, '2751935'
                Plan:ISDN, Type:Subscriber(local)
Feb 15 17:51:08.714: ISDN Se0/2/0:15 Q931: TX -> CALL_PROC pd = 8  callref = 0xE97E
        Channel ID i = 0xA98391
                Exclusive, Channel 17
Feb 15 17:51:08.718: %HTTPC-6-REQUEST_FAILED: request URI http://ipphone.fw.garanti.com.tr/ipphone/musteribilgiler?source=TLC&call_data=005336805920-800321925 failed
Feb 15 17:51:08.718: %IVR-3-APP_ERR: Musteri bilgileri serverdan alinamadi - Hata Kodu: error
Feb 15 17:51:08.798: ISDN Se0/2/0:15 Q931: TX -> ALERTING pd = 8  callref = 0xE97E

Dear
Code 38 Indicates that the network is not functioning correctly and that the condition is likely to last
for an extended period.
to me the GW is not able to make SIP connection and is likely due to incorrect
IP Address is seen from the GW.I hope to share the configuration.  
Thank you
please rate , if this will help

Similar Messages

  • Server https-WEB: CORE0125 The server terminated abnormally with error code

    "Server https-WEB: CORE0125 The server terminated abnormally with error code 0, An attempt will be made to restart it. "
    This happens every time I reboot the server or logoff. It has no ill effect on the server itself except generating these event log errors I am using Sun One 6.1 SP 1 on a wondows 2003 server. I have to resolve this beofore I can go any furthur in my project. Any help? This error comes up for both the web servive and the admin service.

    Thanks to a post I just discovered, I have solved this problem.
    The JVM within Sun Web Server is accepting kill signals from Windows when users logoff. When the JVM dies, apparently the web server service just dies as well. It's a long story and I don't really care to understand it fully.
    You can refer to the thread I found for the solution of passing the JVM a startup option to ignore these signals.
    http://swforum.sun.com/jive/thread.jspa?forumID=16&threadID=23382
    Or, you can just disable the JVM completely as I did. Though there is a checkbox for this for user-defined servers under the Java tab. I couldn't find where to do this for the admin server itself, so I commented out the line in magnus.conf that loads j2ee-plugin.dll.
    We'll see if this causes any other problems, but so far so good.

  • SAP ECC error:'Migration Monitor' exits with error code 103.

    Hi All,
    I am doing SAP ECC installation for windows 32 bit with MAXDB as backend.
    I am stuck at the import ABAP.Getting error
    ERROR 2008-08-08 16:10:53
    CJS-30022  Program 'Migration Monitor' exits with error code 103. For details see log file(s) import_monitor.java.log, import_monitor.log.
    1) imort_monitor.java.log-->contains
    java version "1.4.2_12"
    Java(TM) 2 Runtime Environment, Standard Edition (build 1.4.2_12-b03)
    Java HotSpot(TM) Client VM (build 1.4.2_12-b03, mixed mode)
    Import Monitor jobs: running 1, waiting 0, completed 18, failed 0, total 19.
    Loading of 'SAPVIEW' import package: ERROR
    Import Monitor jobs: running 0, waiting 0, completed 18, failed 1, total 19.
    2)import_monitor.log
    ERROR: 2008-08-08 16:10:36 com.sap.inst.migmon.LoadTask run
    Loading of 'SAPVIEW' import package is interrupted with R3load error.
    Process 'D:\usr\sap\EC6\SYS\exe\uc\NTI386\R3load.exe -i SAPVIEW.cmd -dbcodepage 4103 -l SAPVIEW.log -nolog -c 0' exited with return code 2.
    For mode details see 'SAPVIEW.log' file.
    Standard error output:
    sapparam: sapargv( argc, argv) has not been called.
    sapparam(1c): No Profile used.
    sapparam: SAPSYSTEMNAME neither in Profile nor in Commandline
    INFO: 2008-08-08 16:10:52
    All import packages are processed.
    WARNING: 2008-08-08 16:10:52
    1 error(s) during processing of packages.
    INFO: 2008-08-08 16:10:52
    Import Monitor is stopped.
    3)SAPVIEW.log
      error message returned by DbSl:
    (IMP) INFO: a failed DROP attempt is not necessarily a problem
    (DB) ERROR: DDL statement failed
    (CREATE VIEW "Z_T_CO_BW" ( "KOKRS" , "KOSTL" , "VERSN" , "KSTAR" , "WOG001" , "MEG001"  ) AS SELECT T0002."KOKRS", T0002."KOSTL", T0001."VERSN", T0001."KSTAR", T0001."WOG001",  T0001."MEG001" FROM "COSS" T0001, "CSKS" T0002 WHERE T0002."MANDT" = T0001."MANDT")
    DbSlExecute: rc = 103
      (SQL error -942)
      error message returned by DbSl:
    (DB) INFO: disconnected from DB
    D:\usr\sap\EC6\SYS\exe\uc\NTI386\R3load.exe: job finished with 3108 error(s)
    D:\usr\sap\EC6\SYS\exe\uc\NTI386\R3load.exe: END OF LOG: 20080808174211
    Only SAPDB: SAPSID srvice of SAP DB is only up.
    No other services of database are  up.And i am not able to up the other services also.
    Is it required to up the other services?
    If not?
    Why this error is occuring?
    Any help will be appreciated.
    Thanks&Regards
    Manisha das

    Hello Manisha,
    The one of the possible reasons for this is due to lack of H/W.
    Increase your RAM size to atleast 2GB and utilise the same while you are installing ECC in database parameters step..
    If the issue is with H/W, then this should fix the issue.
    Hope it helps,
    Regards,
    Satish.

  • Calls Getting disconnected with reason code 26

    Hi,
    Few of my calls are getting disconnected with reason code 26. on agent screen it just flash and disconnect.as per RCD its showing Error code 0( fine) and finally its ending at Skill Group Node. talk time is 1 or 2 seconds. agents having auto answer setting as well as IP Phone set auto ans with headset.
    my setup is IPIVR based UCCE setup.
    Please help
    Regards-
    PK

    Hi PK,
    CD 26 normally indicates Resource Not available in CUCM side. please check the Jtapi gateway process logs for the failed calls. you should be able to see something similar to below
    19:08:37:896 PG1A-jgw1 Trace: ConnFailedEv CID: 27224748 Addr: 80002985 CiscoCause: CAUSE_RESOURCESNAVAIL Cause: CAUSE_RESOURCES_NOT_AVAILABLE.
    if that is the case , please check from CUCM perspective as well.
    Regards,
    Sasikumar.

  • Failed to send request/response to peer. send() failed with error code 32?

    hello, chris:
    recently we check the tterros.log, we found the following erros:
    2009-11-12 09:48:18.41 Err : REP: 893538: OCEDATA:transmitter.c(5762): TT16059: Failed to send request/response to peer. send() failed with error code 32
    2009-11-12 09:48:18.41 Err : REP: 893538: OCEDATA:transmitter.c(3048): TT16121: Failed to flush transaction queue. Restarting log read loop
    2009-11-12 12:08:14.19 Err : REP: 893538: OCEDATA:transmitter.c(5762): TT16059: Failed to send request/response to peer. send() failed with error code 32
    2009-11-12 12:08:14.19 Err : REP: 893538: OCEDATA:transmitter.c(3048): TT16121: Failed to flush transaction queue. Restarting log read loop
    what does these mean?? Does this have any effect on replication?? thank you ...

    These messages indicate a loss of connectivity between the replication agents. This could be due to one some kind of failure (e.g. network issue). If the messages are infrequent and replication is otherwise working okay they are not a big cause for concern though if I were you I would check the network etc. for anything abnormal.
    Chris

  • BR0804I BRCONNECT terminated with error code 5

    hi all,
    we r exporting source system , at step 2 "Update database statistice" error occur
    An error occurred while processing service SAP ERP 6.0 Support Release 3 > Software Life-Cycle Options > System Copy > Oracle > Source System Export > Central System > Based on AS ABAP > Database Instance Export( Last error reported by the step :Process call 'G:\usr\sap\PRD\SYS\exe\uc\NTAMD64\brconnect.exe -u / -c -o summary -f stats -o SAPSR3 -t all -m +I -s P10 -f allsel,collect,method,precision,space,keep -p 4' exits with error code 5. For details see log file(s) brconnect.log.). You may now
    choose Retry to repeat the current step.
    choose View Log to get more information about the error.
    stop the task and continue with it later.
    Log files are written to C:\Program Files/sapinst_instdir/ERP/LM/COPY/ORA/EXP/CENTRAL/AS-ABAP/EXP.
    BR0280I BRCONNECT thread 2: time stamp: 2010-03-17 13.32.29
    BR0850I 69902 of 69902 objects processed - 82.467 of 82.467 units done
    BR0204I Percentage done: 100.00%, estimated end time: 13:32
    BR0001I **************************************************
    BR0280I BRCONNECT time stamp: 2010-03-17 13.32.29
    BR0848I Thread 2 finished with return code 0
    BR0280I BRCONNECT time stamp: 2010-03-17 13.32.29
    BR0879I Statistics checked for 0 tables
    BR0878I Number of tables selected to collect statistics after check: 0
    BR0880I Statistics collected for 69902/0 tables/indexes
    BR0889I Structure validated for 0/83617/0 tables/indexes/clusters
    BR0806I End of BRCONNECT processing: cecuoaya.sta 2010-03-17 13.32.29
    BR0280I BRCONNECT time stamp: 2010-03-17 13.32.30
    BR0804I BRCONNECT terminated with errors
    ERROR      2010-03-17 13:32:30.171
               CJSlibModule::writeError_impl()
    CJS-30023  Process call 'G:\usr\sap\PRD\SYS\exe\uc\NTAMD64\brconnect.exe -u / -c -o summary -f stats -o SAPSR3 -t all -m +I -s P10 -f allsel,collect,method,precision,space,keep -p 4' exits with error code 5. For details see log file(s) brconnect.log.
    ERROR      2010-03-17 13:32:30.187 [sixxcstepexecute.cpp:951]
    FCO-00011  The step updateOracleStatistics with step key |NW_Export|ind|ind|ind|ind|0|0|NW_Export_Pre|ind|ind|ind|ind|3|0|NW_ORA_Statistics_Update|ind|ind|ind|ind|0|0|updateOracleStatistics was executed with status ERROR ( Last error reported by the step :Process call 'G:\usr\sap\PRD\SYS\exe\uc\NTAMD64\brconnect.exe -u / -c -o summary -f stats -o SAPSR3 -t all -m +I -s P10 -f allsel,collect,method,precision,space,keep -p 4' exits with error code 5. For details see log file(s) brconnect.log.)
    plz guide

    hi,
    TST03, drop and recreate the index now export has failed 2 job outof 43,
    export_monitor.java.log
    Unloading of 'SAPAPPL0_4' export package: OK
    Export Monitor jobs: running 1, waiting 30, completed 12, failed 0, total 43.
    Export Monitor jobs: running 2, waiting 29, completed 12, failed 0, total 43.
    Export Monitor jobs: running 3, waiting 28, completed 12, failed 0, total 43.
    Unloading of 'SAPAPPL1_2' export package: ERROR
    Export Monitor jobs: running 2, waiting 28, completed 12, failed 1, total 43.
    Export Monitor jobs: running 3, waiting 27, completed 12, failed 1, total 43.
    Unloading of 'SAPAPPL1_3' export package: ERROR
    Export Monitor jobs: running 2, waiting 27, completed 12, failed 2, total 43.
    Export Monitor jobs: running 3, waiting 26, completed 12, failed 2, total 43.
    'SAPAPPL1_2.log
    (RTF) ########## WARNING ###########
         Without ORDER BY PRIMARY KEY the exported data may be unusable for some databases
    G:\usr\sap\PRD\SYS\exe\uc\NTAMD64\R3load.exe: job completed
    G:\usr\sap\PRD\SYS\exe\uc\NTAMD64\R3load.exe: END OF LOG: 20100319145456
    G:\usr\sap\PRD\SYS\exe\uc\NTAMD64\R3load.exe: START OF LOG: 20100319145456
    G:\usr\sap\PRD\SYS\exe\uc\NTAMD64\R3load.exe: sccsid @(#) $Id: //bas/700_REL/src/R3ld/R3load/R3ldmain.c#18 $ SAP
    G:\usr\sap\PRD\SYS\exe\uc\NTAMD64\R3load.exe: version R7.00/V1.4 [UNICODE]
    Compiled Nov 18 2008 23:19:12
    G:\usr\sap\PRD\SYS\exe\uc\NTAMD64\R3load.exe -e SAPAPPL1_2.cmd -datacodepage 4103 -l SAPAPPL1_2.log -stop_on_error
    (DB) INFO: connected to DB
    (DB) INFO: DbSlControl(DBSL_CMD_NLS_CHARACTERSET_GET): UTF8
    (DB) INFO: Export without hintfile
    (GSI) INFO: dbname   = "PRD20090418030425                                                                                "
    (GSI) INFO: vname    = "ORACLE                          "
    (GSI) INFO: hostname = "PRDSAP                                                          "
    (GSI) INFO: sysname  = "Windows NT"
    (GSI) INFO: nodename = "PRDSAP"
    (GSI) INFO: release  = "5.2"
    (GSI) INFO: version  = "3790 Service Pack 1"
    (GSI) INFO: machine  = "8x AMD64 Level 6 (Mod 23 Step 10)"
    (GSI) INFO: instno   = "0020500723"
    EXP) TABLE: "K002" #20100319145654
    (EXP) ERROR: DbSlExeRead failed
      rc = 103, table "K9RPRD7000001"
      (SQL error 942)
      error message returned by DbSl:
    ORA-00942: table or view does not exist
    (DB) INFO: disconnected from DB
    G:\usr\sap\PRD\SYS\exe\uc\NTAMD64\R3load.exe: job finished with 1 error(s)
    G:\usr\sap\PRD\SYS\exe\uc\NTAMD64\R3load.exe: END OF LOG: 20100319145654
    SAPAPPL1_3.log
    G:\usr\sap\PRD\SYS\exe\uc\NTAMD64\R3load.exe: START OF LOG: 20100319145655
    G:\usr\sap\PRD\SYS\exe\uc\NTAMD64\R3load.exe: sccsid @(#) $Id: //bas/700_REL/src/R3ld/R3load/R3ldmain.c#18 $ SAP
    G:\usr\sap\PRD\SYS\exe\uc\NTAMD64\R3load.exe: version R7.00/V1.4 [UNICODE]
    Compiled Nov 18 2008 23:19:12
    G:\usr\sap\PRD\SYS\exe\uc\NTAMD64\R3load.exe -ctf E I:\PRD_Exp\ABAP\DATA\SAPAPPL1_3.STR I:\PRD_Exp\ABAP\DB\DDLORA_LRG.TPL SAPAPPL1_3.TSK ORA -l SAPAPPL1_3.log
    (RTF) ########## WARNING ###########
         Without ORDER BY PRIMARY KEY the exported data may be unusable for some databases
    G:\usr\sap\PRD\SYS\exe\uc\NTAMD64\R3load.exe: job completed
    G:\usr\sap\PRD\SYS\exe\uc\NTAMD64\R3load.exe: END OF LOG: 20100319145656
    G:\usr\sap\PRD\SYS\exe\uc\NTAMD64\R3load.exe: START OF LOG: 20100319145656
    G:\usr\sap\PRD\SYS\exe\uc\NTAMD64\R3load.exe: sccsid @(#) $Id: //bas/700_REL/src/R3ld/R3load/R3ldmain.c#18 $ SAP
    G:\usr\sap\PRD\SYS\exe\uc\NTAMD64\R3load.exe: version R7.00/V1.4 [UNICODE]
    Compiled Nov 18 2008 23:19:12
    G:\usr\sap\PRD\SYS\exe\uc\NTAMD64\R3load.exe -e SAPAPPL1_3.cmd -datacodepage 4103 -l SAPAPPL1_3.log -stop_on_error
    (DB) INFO: connected to DB
    (DB) INFO: DbSlControl(DBSL_CMD_NLS_CHARACTERSET_GET): UTF8
    (DB) INFO: Export without hintfile
    (GSI) INFO: dbname   = "PRD20090418030425                                                                                "
    (GSI) INFO: vname    = "ORACLE                          "
    (GSI) INFO: hostname = "PRDSAP                                                          "
    (GSI) INFO: sysname  = "Windows NT"
    (GSI) INFO: nodename = "PRDSAP"
    (GSI) INFO: release  = "5.2"
    (GSI) INFO: version  = "3790 Service Pack 1"
    (GSI) INFO: machine  = "8x AMD64 Level 6 (Mod 23 Step 10)"
    (GSI) INFO: instno   = "0020500723"
    EXP) ERROR: DbSlExeRead failed
      rc = 103, table "QCMZPORD_LINE"
      (SQL error 942)
      error message returned by DbSl:
    ORA-00942: table or view does not exist
    (DB) INFO: disconnected from DB
    G:\usr\sap\PRD\SYS\exe\uc\NTAMD64\R3load.exe: job finished with 1 error(s)
    G:\usr\sap\PRD\SYS\exe\uc\NTAMD64\R3load.exe: END OF LOG: 20100319145717

  • Startdb: Terminating with error code 12

    Hi,
    We are running ECC6.0.Databse : Oracle & OS : Solaris. I have done a new installation & after system copy when we start the sap I got the following error :
    Running /usr/sap/QLT/SYS/exe/run/startdb
    Trying to start QLT database ...
    Log file: /export/home/qltadm/startdb.log
    /usr/sap/QLT/SYS/exe/run/startdb: Terminating with error code 12
    DB startup failed
    Following is the error in startdb.log
    qltadm> more startdb.log
    Sun Aug 22 15:37:23 IST 2010
    LOGFILE FOR STARTING ORACLE
    Trying to start QLT database ...
    Sun Aug 22 15:37:23 IST 2010
    checking required environment variables
    ORACLE_HOME  is >/oracle/QLT/102_64<
    ORACLE_SID   is >QLT<
    Sun Aug 22 15:37:23 IST 2010
    check initora
    Sun Aug 22 15:37:23 IST 2010
    check initora
    Sun Aug 22 15:37:23 IST 2010
    checking V2 connect
    TNS Ping Utility for Solaris: Version 10.2.0.2.0 - Production on 22-AUG-2010 15:37:23
    Copyright (c) 1997, 2005, Oracle.  All rights reserved.
    Used parameter files:
    /usr/sap/QLT/SYS/profile/oracle/sqlnet.ora
    Used TNSNAMES adapter to resolve the alias
    Attempting to contact (DESCRIPTION = (ADDRESS_LIST = (ADDRESS = (COMMUNITY = SAP.WORLD) (PROTOCOL = TCP) (HOST = lumax-qal) (PORT = 1
    527))) (CONNECT_DATA = (SID = QLT) (GLOBAL_NAME = QLT.WORLD)))
    OK (10 msec)
    tnsping: V2 connect to QLT
    Sun Aug 22 15:37:23 IST 2010
    Connect to the database to check the database state:
    R3trans: connect check finished with return code: 12
    Database not available
    Sun Aug 22 15:37:23 IST 2010
    Shutdown database
    First trying to shutdown the database - May be,
    the database is in the nomount or mount state
    Sun Aug 22 15:37:47 IST 2010
    starting database
    SQL*Plus: Release 10.2.0.2.0 - Production on Sun Aug 22 15:37:48 2010
    Copyright (c) 1982, 2005, Oracle.  All Rights Reserved.
    Connected to an idle instance.
    ORACLE instance started.
    Total System Global Area 4747952128 bytes
    Fixed Size                  2035280 bytes
    Variable Size            2399146416 bytes
    Database Buffers         2332033024 bytes
    Redo Buffers               14737408 bytes
    Database mounted.
    Database opened.
    Disconnected from Oracle Database 10g Enterprise Edition Release 10.2.0.2.0 - 64bit Production
    With the Partitioning and Data Mining options
    Sun Aug 22 15:38:03 IST 2010
    Connect to the database to verify, that the database is now open
    R3trans check finished with return code: 12
    ERROR: Startup of database failed
        Notify Database Administrator.
    /usr/sap/QLT/SYS/exe/run/startdb: Terminating with error code 12
    qltadm>
    Pl help in resolving this issue.
    Thanks

    Is your listener running? If not check your logs ...
    Often you get this when DB isn't running and SAP needs to connect in order to start.
    Also consider this - that if your environment is on cluster technology then startsap won't work - you will need something like this:
    - As sidadm
    startdb
    startsap -t r3 -i ASCS00 -v c123biXXXacsxx
    startsap -t r3 -i DVEBMGS00 -v c123dbXXXdbqxx

  • /usr/sap/QAS/SYS/exe/run/startdb: Terminating with error code 12

    Hi Experts,
    We have made a system copy from Production to Quality and it has been done successfully. Now we are able to open the database manually.  But when we are trying to start SAP it is not connecting the database base and it is giving error which is given below :
    /home/qasadm/startdb.log
    Copyright (c) 1982, 2005, Oracle.  All Rights Reserved.
    Connected to an idle instance.
    ORACLE instance started.
    Total System Global Area 4764729344 bytes
    Fixed Size                  2035312 bytes
    Variable Size            2432700816 bytes
    Database Buffers         2315255808 bytes
    Redo Buffers               14737408 bytes
    Database mounted.
    Database opened.
    Disconnected from Oracle Database 10g Enterprise Edition Release 10.2.0.2.0 - 64bit Production
    With the Partitioning and Data Mining options
    Mon Apr 12 10:45:40 IST 2010
    Connect to the database to verify, that the database is now open
    R3trans check finished with return code: 12
    ERROR: Startup of database failed
        Notify Database Administrator.
    /usr/sap/QAS/SYS/exe/run/startdb: Terminating with error code 12
    ^C
    root@bsltest # tail -f /home/qasadm/startdb.log
    Connect to the database to check the database state:
    R3trans: connect check finished with return code: 12
    Database not available
    Mon Apr 12 10:55:53 IST 2010
    Shutdown database
    First trying to shutdown the database - May be,
    the database is in the nomount or mount state
    Mon Apr 12 10:56:22 IST 2010
    starting database
    SQL*Plus: Release 10.2.0.2.0 - Production on Mon Apr 12 10:56:22 2010
    Copyright (c) 1982, 2005, Oracle.  All Rights Reserved.
    Connected to an idle instance.
    ORACLE instance started.
    Total System Global Area 4764729344 bytes
    Fixed Size                  2035312 bytes
    Variable Size            2432700816 bytes
    Database Buffers         2315255808 bytes
    Redo Buffers               14737408 bytes
    Database mounted.
    Database opened.
    Disconnected from Oracle Database 10g Enterprise Edition Release 10.2.0.2.0 - 64bit Production
    With the Partitioning and Data Mining options
    Mon Apr 12 10:56:42 IST 2010
    Connect to the database to verify, that the database is now open
    R3trans check finished with return code: 12
    ERROR: Startup of database failed
        Notify Database Administrator.
    /usr/sap/QAS/SYS/exe/run/startdb: Terminating with error code 12
    Kindly see the logs and request you to kindly help us how it will resolve this issue.
    Regards,
    Jitendra

    We have made a system copy from Production to Quality
    After client copy sap schema had been changed thats why its not connecting.
    fyi: Client copy and system copy both are different
    schema had been changed thats why its not connecting
    This is one of the post installation step after doing a system copy(reffer the ssytem copy guide)
    Problem has resolved
    Great, suggest you to close this thread
    Regards,
    Nick Loy

  • Transport control program tp ended with error code 0212

    Hi all,
    I have created a two system landscape of development & production server. But while I am releasing any request from develpoment server a error is showing: " Transport control program tp ended with error code 0212 Errors: could not access file as supposed (see dev_tp or S".I have chosen development server as domain controller. TMS alert viewer error message also contains the following information------>command: TMS_MGR_READ_TRANSPORT_QUEUE
                                                                           service: transport service
                                                                           start : online
                                                                           Function: TMS_TP_SHOW_BUFFER
                                                                           message: TP_REPORTED_ERROR
    In import monitor it's showing : "tp finished: could not access file as supposed (see dev_tp or SLOG1113.K"
    Can you tell me how to resolve this issue?

    dev_tp contains:    
    This is R3trans.exe version 6.14 (release 700 - 09.04.10 - 11:26:00).
    unicode enabled version
    usage: R3trans.exe [<options>] <control_file>
    The control_file describes what R3trans has to do.
    The following options are possible:
    -c f1 f2 : Copy file f1 to f2 with character set conversion.
    -d       : DB connect. Test if SAP database is available.
    -i file  : Import from file without using a control file.
    -l file  : List the contents of file to the log file.
    -m file  : List the contents of file to allow tp to create a cofile.
    -t       : Test. All database changes are rolled back.
    -t4      : Trace level 4. Switch on developer trace.
    -u <int> : Unconditional modes. See below.
    -v       : Verbose. Write more details to the log file.
    -w file  : Log file. The default log file is 'trans.log'.
    -x       : DB connect without access on any SAP table.
    R3trans.exe finished (0012).
    & the slog file is not there in the trans/log directory

  • Installation of Photoshop update 13.1.2 for creative cloud fails with error code U44M1P7 I need help

    I need help installing update 13.1.2 for Photoshop creative cloud, installation fails with error code: U44M1P7. Could someone please help?

    Sorry to bother you.
    I could find the answer after searching previous posts about this language problem.
    Had to change my language in AAM profile and then download PS CS6 again ( english version ).
    Then open the actual Photoshop and in preferences > interface you can besides the Dutch also option for English.
    restart application and Voila.
    Greetz, Jeroen

  • SAP on V6R1 - ABAP Import:Program 'Migration Monitor' exits with error code

    Hello,
    We are doing an installation of SAP NW 7.01 SR1 on V6R1.
    <br>
    We were getting error in SAPAPPL2.TSK.bck we merged the files with following command:R3load --merge_only <TSK file> and refering sap note:Note 455195 - R3load: Use of TSK files.
    <br>
    We are again getting error in following steps:
    <br>
    sapinst.log
    <br>
    <br>WARNING 2009-09-30 23:25:28.477
    Execution of the command "Y:\QOpenSys\QIBM\ProdData\JavaVM\jdk14\64bit\bin\java -classpath migmon.jar -showversion -Xmx1024m com.sap.inst.migmon.imp.ImportMonitor -sapinst" finished with return code 103. Output:
    java version "1.4.2"
    Java(TM) 2 Runtime Environment, Standard Edition (build 2.3)
    IBM J9 VM (build 2.3, J2RE 1.4.2 IBM J9 2.3 OS400 ppc64-64 j9ap64142sr13-20090310 (JIT enabled)
    J9VM - 20090309_31291_BHdSMr
    JIT  - 20090210_1447ifx1_r8
    GC   - 200902_24)
    I<br>mport Monitor jobs: running 1, waiting 27, completed 0, failed 0, total 28.
    <br>Loading of 'SAPNTAB' import package: OK
    <br>Import Monitor jobs: running 0, waiting 27, completed 1, failed 0, total 28.
    Import Monitor jobs: running 1, waiting 26, completed 1, failed 0, total 28.<br>
    Import Monitor jobs: running 2, waiting 25, completed 1, failed 0, total 28.<br>
    Import Monitor jobs: running 3, waiting 24, completed 1, failed 0, total 28.<br>
    Loading of 'DOKCLU' import package: OK
    Import Monitor jobs: running 2, waiting 24, completed 2, failed 0, total 28.<br>
    Import Monitor jobs: running 3, waiting 23, completed 2, failed 0, total 28.<br>
    Loading of 'SAPAPPL1' import package: OK
    Import Monitor jobs: running 2, waiting 23, completed 3, failed 0, total 28.<br>
    Import Monitor jobs: running 3, waiting 22, completed 3, failed 0, total 28.<br>
    Loading of 'SAPAPPL2' import package: ERROR
    Import Monitor jobs: running 2, waiting 22, completed 3, failed 1, total 28.<br>
    Import Monitor jobs: running 3, waiting 21, completed 3, failed 1, total 28.<br>
    Loading of 'DD03L' import package: OK
    Import Monitor jobs: running 2, waiting 21, completed 4, failed 1, total 28.<br>
    Import Monitor jobs: running 3, waiting 20, completed 4, failed 1, total 28.<br>
    Loading of 'SCPRSVALS' import package: OK
    Import Monitor jobs: running 2, waiting 20, completed 5, failed 1, total 28.<br>
    Import Monitor jobs: running 3, waiting 19, completed 5, failed 1, total 28.<br>
    Loading of 'SAPSDIC' import package: OK
    Import Monitor jobs: running 2, waiting 19, completed 6, failed 1, total 28.<br>
    Import Monitor jobs: running 3, waiting 18, completed 6, failed 1, total 28.<br>
    Loading of 'SCPRVALS' import package: OK
    Import Monitor jobs: running 2, waiting 18, completed 7, failed 1, total 28.<br>
    Import Monitor jobs: running 3, waiting 17, completed 7, failed 1, total 28.<br>
    Loading of 'SAPSSRC' import package: OK
    Import Monitor jobs: running 2, waiting 17, completed 8, failed 1, total 28.<br>
    Import Monitor jobs: running 3, waiting 16, completed 8, failed 1, total 28.<br>
    Loading of 'FUPARAREF' import package: OK
    Import Monitor jobs: running 2, waiting 16, completed 9, failed 1, total 28.<br>
    Import Monitor jobs: running 3, waiting 15, completed 9, failed 1, total 28.<br>
    Loading of 'TODIR' import package: OK
    Import Monitor jobs: running 2, waiting 15, completed 10, failed 1, total 28.<br>
    Import Monitor jobs: running 3, waiting 14, completed 10, failed 1, total 28.<br>
    Loading of 'SEOSUBCODF' import package: OK
    Import Monitor jobs: running 2, waiting 14, completed 11, failed 1, total 28.<br>
    Import Monitor jobs: running 3, waiting 13, completed 11, failed 1, total 28.<br>
    Loading of 'E071K' import package: OK
    Import Monitor jobs: running 2, waiting 13, completed 12, failed 1, total 28.<br>
    Import Monitor jobs: running 3, waiting 12, completed 12, failed 1, total 28.<br>
    Loading of 'SAPPOOL' import package: OK
    Import Monitor jobs: running 2, waiting 12, completed 13, failed 1, total 28.<br>
    Import Monitor jobs: running 3, waiting 11, completed 13, failed 1, total 28.<br>
    Loading of 'SAPSPROT' import package: OK
    Import Monitor jobs: running 2, waiting 11, completed 14, failed 1, total 28.<br>
    Import Monitor jobs: running 3, waiting 10, completed 14, failed 1, total 28.<br>
    Loading of 'SAPSDOCU' import package: OK
    Import Monitor jobs: running 2, waiting 10, completed 15, failed 1, total 28.<br>
    Import Monitor jobs: running 3, waiting 9, completed 15, failed 1, total 28.<br>
    Loading of 'SAPCLUST' import package: OK
    Import Monitor jobs: running 2, waiting 9, completed 16, failed 1, total 28.<br>
    Import Monitor jobs: running 3, waiting 8, completed 16, failed 1, total 28.<br>
    Loading of 'SAPSLOAD' import package: OK
    Import Monitor jobs: running 2, waiting 8, completed 17, failed 1, total 28.<br>
    Import Monitor jobs: running 3, waiting 7, completed 17, failed 1, total 28.<br>
    Loading of 'SAPSLEXC' import package: OK
    Import Monitor jobs: running 2, waiting 7, completed 18, failed 1, total 28.<br>
    Import Monitor jobs: running 3, waiting 6, completed 18, failed 1, total 28.<br>
    Loading of 'SAPUSER' import package: OK
    Import Monitor jobs: running 2, waiting 6, completed 19, failed 1, total 28.<br>
    Import Monitor jobs: running 3, waiting 5, completed 19, failed 1, total 28.<br>
    Loading of 'SAPDDIM' import package: OK
    Import Monitor jobs: running 2, waiting 5, completed 20, failed 1, total 28.<br>
    Import Monitor jobs: running 3, waiting 4, completed 20, failed 1, total 28.<br>
    Loading of 'SAPDFACT' import package: OK
    Import Monitor jobs: running 2, waiting 4, completed 21, failed 1, total 28.<br>
    Import Monitor jobs: running 3, waiting 3, completed 21, failed 1, total 28.<br>
    Loading of 'SAPDODS' import package: OK
    Import Monitor jobs: running 2, waiting 3, completed 22, failed 1, total 28.<br>
    Import Monitor jobs: running 3, waiting 2, completed 22, failed 1, total 28.<br>
    Loading of 'SAPUSER1' import package: OK
    Import Monitor jobs: running 2, waiting 2, completed 23, failed 1, total 28.<br>
    Import Monitor jobs: running 3, waiting 1, completed 23, failed 1, total 28.<br>
    Loading of 'SAP0000' import package: OK
    Import Monitor jobs: running 2, waiting 1, completed 24, failed 1, total 28.<br>
    Loading of 'SAPAPPL0' import package: OK
    Import Monitor jobs: running 1, waiting 1, completed 25, failed 1, total 28.<br>
    Loading of 'SAPSSEXC' import package: OK
    Import Monitor jobs: running 0, waiting 1, completed 26, failed 1, total 28.<br>
    <br>
    WARNING[E] 2009-09-30 23:25:28.524
    CJS-30022  Program 'Migration Monitor' exits with error code 103. For details see log file(s) import_monitor.java.log,
    <br>
    ERROR 2009-09-30 23:25:28.914
    FCO-00011  The step runMigrationMonitor with step key |NW_ABAP_OneHost|ind|ind|ind|ind|0|0|NW_Onehost_System|ind|ind|ind|ind|1|0|NW_CreateDBandLoad|ind|ind|ind|ind|10|0|NW_ABAP_Import_Dialog|ind|ind|ind|ind|5|0|NW_ABAP_Import|ind|ind|ind|ind|0|0|runMigrationMonitor was executed with status ERROR .
    <br>
    <br>import_monitor.log.
    <br>****************************************************************************************************************************************************
    <br>INFO: 2009-09-30 23:26:33 com.sap.inst.migmon.LoadTask run
    Loading of 'SAP0000' import package is successfully completed.
    <br>
    INFO: 2009-09-30 23:30:31 com.sap.inst.migmon.LoadTask run
    Loading of 'SAPAPPL0' import package is successfully completed.
    <br>
    INFO: 2009-09-30 23:31:16 com.sap.inst.migmon.LoadTask run
    Loading of 'SAPSSEXC' import package is successfully completed.
    <br>
    WARNING: 2009-09-30 23:31:31
    Cannot start import of packages with views because not all import packages with tables are loaded successfully.
    WARNING: 2009-09-30 23:31:31
    1 error(s) during processing of packages.
    INFO: 2009-09-30 23:31:31
    Import Monitor is stopped.
    <br>*************************************************************************************************************************************************
    <br>SAPAPPL02.LOG
    <br>**************************************************************************************************************************************************
    <br>TVV1 in *LIBL type *FILE not found. MSGID= Job=015908/SAPINST/QJVAEXEC
    (IMP) INFO: a failed DROP attempt is not necessarily a problem
    (DB) INFO: TVV1 created #20091001110304
    <br>
    (DB) INFO: TVV1 deleted/truncated #20091001110304
    <br>
    (IMP) INFO: import of TVV1 completed (0 rows) #20091001110304
    <br>
    (DB) ERROR: DDL statement failed<br>
    (ALTER TABLE "TVV1" DROP PRIMARY KEY )<br>
    DbSlExecute: rc = 99<br>
      (SQL error -539)<br>
      error message returned by DbSl:
    Table TVV1 in R3E04DATA does not have a primary or unique key. MSGID= Job=015908/SAPINST/QJVAEXEC
    Your inputs will help a lot.
    Regards,
    Prasad

    Hello,
    We are doing an installation of SAP NW 7.01 SR1 on V6R1.
    <br>
    We were getting error in SAPAPPL2.TSK.bck we merged the files with following command:R3load --merge_only <TSK file> and refering sap note:Note 455195 - R3load: Use of TSK files.
    <br>
    We are again getting error in following steps:
    <br>
    sapinst.log
    <br>
    <br>WARNING 2009-09-30 23:25:28.477
    Execution of the command "Y:\QOpenSys\QIBM\ProdData\JavaVM\jdk14\64bit\bin\java -classpath migmon.jar -showversion -Xmx1024m com.sap.inst.migmon.imp.ImportMonitor -sapinst" finished with return code 103. Output:
    java version "1.4.2"
    Java(TM) 2 Runtime Environment, Standard Edition (build 2.3)
    IBM J9 VM (build 2.3, J2RE 1.4.2 IBM J9 2.3 OS400 ppc64-64 j9ap64142sr13-20090310 (JIT enabled)
    J9VM - 20090309_31291_BHdSMr
    JIT  - 20090210_1447ifx1_r8
    GC   - 200902_24)
    I<br>mport Monitor jobs: running 1, waiting 27, completed 0, failed 0, total 28.
    <br>Loading of 'SAPNTAB' import package: OK
    <br>Import Monitor jobs: running 0, waiting 27, completed 1, failed 0, total 28.
    Import Monitor jobs: running 1, waiting 26, completed 1, failed 0, total 28.<br>
    Import Monitor jobs: running 2, waiting 25, completed 1, failed 0, total 28.<br>
    Import Monitor jobs: running 3, waiting 24, completed 1, failed 0, total 28.<br>
    Loading of 'DOKCLU' import package: OK
    Import Monitor jobs: running 2, waiting 24, completed 2, failed 0, total 28.<br>
    Import Monitor jobs: running 3, waiting 23, completed 2, failed 0, total 28.<br>
    Loading of 'SAPAPPL1' import package: OK
    Import Monitor jobs: running 2, waiting 23, completed 3, failed 0, total 28.<br>
    Import Monitor jobs: running 3, waiting 22, completed 3, failed 0, total 28.<br>
    Loading of 'SAPAPPL2' import package: ERROR
    Import Monitor jobs: running 2, waiting 22, completed 3, failed 1, total 28.<br>
    Import Monitor jobs: running 3, waiting 21, completed 3, failed 1, total 28.<br>
    Loading of 'DD03L' import package: OK
    Import Monitor jobs: running 2, waiting 21, completed 4, failed 1, total 28.<br>
    Import Monitor jobs: running 3, waiting 20, completed 4, failed 1, total 28.<br>
    Loading of 'SCPRSVALS' import package: OK
    Import Monitor jobs: running 2, waiting 20, completed 5, failed 1, total 28.<br>
    Import Monitor jobs: running 3, waiting 19, completed 5, failed 1, total 28.<br>
    Loading of 'SAPSDIC' import package: OK
    Import Monitor jobs: running 2, waiting 19, completed 6, failed 1, total 28.<br>
    Import Monitor jobs: running 3, waiting 18, completed 6, failed 1, total 28.<br>
    Loading of 'SCPRVALS' import package: OK
    Import Monitor jobs: running 2, waiting 18, completed 7, failed 1, total 28.<br>
    Import Monitor jobs: running 3, waiting 17, completed 7, failed 1, total 28.<br>
    Loading of 'SAPSSRC' import package: OK
    Import Monitor jobs: running 2, waiting 17, completed 8, failed 1, total 28.<br>
    Import Monitor jobs: running 3, waiting 16, completed 8, failed 1, total 28.<br>
    Loading of 'FUPARAREF' import package: OK
    Import Monitor jobs: running 2, waiting 16, completed 9, failed 1, total 28.<br>
    Import Monitor jobs: running 3, waiting 15, completed 9, failed 1, total 28.<br>
    Loading of 'TODIR' import package: OK
    Import Monitor jobs: running 2, waiting 15, completed 10, failed 1, total 28.<br>
    Import Monitor jobs: running 3, waiting 14, completed 10, failed 1, total 28.<br>
    Loading of 'SEOSUBCODF' import package: OK
    Import Monitor jobs: running 2, waiting 14, completed 11, failed 1, total 28.<br>
    Import Monitor jobs: running 3, waiting 13, completed 11, failed 1, total 28.<br>
    Loading of 'E071K' import package: OK
    Import Monitor jobs: running 2, waiting 13, completed 12, failed 1, total 28.<br>
    Import Monitor jobs: running 3, waiting 12, completed 12, failed 1, total 28.<br>
    Loading of 'SAPPOOL' import package: OK
    Import Monitor jobs: running 2, waiting 12, completed 13, failed 1, total 28.<br>
    Import Monitor jobs: running 3, waiting 11, completed 13, failed 1, total 28.<br>
    Loading of 'SAPSPROT' import package: OK
    Import Monitor jobs: running 2, waiting 11, completed 14, failed 1, total 28.<br>
    Import Monitor jobs: running 3, waiting 10, completed 14, failed 1, total 28.<br>
    Loading of 'SAPSDOCU' import package: OK
    Import Monitor jobs: running 2, waiting 10, completed 15, failed 1, total 28.<br>
    Import Monitor jobs: running 3, waiting 9, completed 15, failed 1, total 28.<br>
    Loading of 'SAPCLUST' import package: OK
    Import Monitor jobs: running 2, waiting 9, completed 16, failed 1, total 28.<br>
    Import Monitor jobs: running 3, waiting 8, completed 16, failed 1, total 28.<br>
    Loading of 'SAPSLOAD' import package: OK
    Import Monitor jobs: running 2, waiting 8, completed 17, failed 1, total 28.<br>
    Import Monitor jobs: running 3, waiting 7, completed 17, failed 1, total 28.<br>
    Loading of 'SAPSLEXC' import package: OK
    Import Monitor jobs: running 2, waiting 7, completed 18, failed 1, total 28.<br>
    Import Monitor jobs: running 3, waiting 6, completed 18, failed 1, total 28.<br>
    Loading of 'SAPUSER' import package: OK
    Import Monitor jobs: running 2, waiting 6, completed 19, failed 1, total 28.<br>
    Import Monitor jobs: running 3, waiting 5, completed 19, failed 1, total 28.<br>
    Loading of 'SAPDDIM' import package: OK
    Import Monitor jobs: running 2, waiting 5, completed 20, failed 1, total 28.<br>
    Import Monitor jobs: running 3, waiting 4, completed 20, failed 1, total 28.<br>
    Loading of 'SAPDFACT' import package: OK
    Import Monitor jobs: running 2, waiting 4, completed 21, failed 1, total 28.<br>
    Import Monitor jobs: running 3, waiting 3, completed 21, failed 1, total 28.<br>
    Loading of 'SAPDODS' import package: OK
    Import Monitor jobs: running 2, waiting 3, completed 22, failed 1, total 28.<br>
    Import Monitor jobs: running 3, waiting 2, completed 22, failed 1, total 28.<br>
    Loading of 'SAPUSER1' import package: OK
    Import Monitor jobs: running 2, waiting 2, completed 23, failed 1, total 28.<br>
    Import Monitor jobs: running 3, waiting 1, completed 23, failed 1, total 28.<br>
    Loading of 'SAP0000' import package: OK
    Import Monitor jobs: running 2, waiting 1, completed 24, failed 1, total 28.<br>
    Loading of 'SAPAPPL0' import package: OK
    Import Monitor jobs: running 1, waiting 1, completed 25, failed 1, total 28.<br>
    Loading of 'SAPSSEXC' import package: OK
    Import Monitor jobs: running 0, waiting 1, completed 26, failed 1, total 28.<br>
    <br>
    WARNING[E] 2009-09-30 23:25:28.524
    CJS-30022  Program 'Migration Monitor' exits with error code 103. For details see log file(s) import_monitor.java.log,
    <br>
    ERROR 2009-09-30 23:25:28.914
    FCO-00011  The step runMigrationMonitor with step key |NW_ABAP_OneHost|ind|ind|ind|ind|0|0|NW_Onehost_System|ind|ind|ind|ind|1|0|NW_CreateDBandLoad|ind|ind|ind|ind|10|0|NW_ABAP_Import_Dialog|ind|ind|ind|ind|5|0|NW_ABAP_Import|ind|ind|ind|ind|0|0|runMigrationMonitor was executed with status ERROR .
    <br>
    <br>import_monitor.log.
    <br>****************************************************************************************************************************************************
    <br>INFO: 2009-09-30 23:26:33 com.sap.inst.migmon.LoadTask run
    Loading of 'SAP0000' import package is successfully completed.
    <br>
    INFO: 2009-09-30 23:30:31 com.sap.inst.migmon.LoadTask run
    Loading of 'SAPAPPL0' import package is successfully completed.
    <br>
    INFO: 2009-09-30 23:31:16 com.sap.inst.migmon.LoadTask run
    Loading of 'SAPSSEXC' import package is successfully completed.
    <br>
    WARNING: 2009-09-30 23:31:31
    Cannot start import of packages with views because not all import packages with tables are loaded successfully.
    WARNING: 2009-09-30 23:31:31
    1 error(s) during processing of packages.
    INFO: 2009-09-30 23:31:31
    Import Monitor is stopped.
    <br>*************************************************************************************************************************************************
    <br>SAPAPPL02.LOG
    <br>**************************************************************************************************************************************************
    <br>TVV1 in *LIBL type *FILE not found. MSGID= Job=015908/SAPINST/QJVAEXEC
    (IMP) INFO: a failed DROP attempt is not necessarily a problem
    (DB) INFO: TVV1 created #20091001110304
    <br>
    (DB) INFO: TVV1 deleted/truncated #20091001110304
    <br>
    (IMP) INFO: import of TVV1 completed (0 rows) #20091001110304
    <br>
    (DB) ERROR: DDL statement failed<br>
    (ALTER TABLE "TVV1" DROP PRIMARY KEY )<br>
    DbSlExecute: rc = 99<br>
      (SQL error -539)<br>
      error message returned by DbSl:
    Table TVV1 in R3E04DATA does not have a primary or unique key. MSGID= Job=015908/SAPINST/QJVAEXEC
    Your inputs will help a lot.
    Regards,
    Prasad

  • DAG - Backup failing on 1 DB only with error - The Microsoft Exchange Replication service VSS Writer instance ID failed with error code 80070020 when preparing for a backup of database 'DB012'

    Hi Board,
    i´ve search across the board, technet and symantec sites but did not found a hint about my problem.
    we drive a 2 node DAG (Location1-Ex1-mb1 
    Location2-exc1-mb1), on SP2 RU4 patchlevel with 40 Databases.
    Since some time the backup of one - and only one DB - is failing with these events, logged on the Mailboxserver on which the passive DB is hosted.
    Log Name:      Application
    Source:        MSExchangeRepl
    Date:          28.09.2012 00:37:17
    Event ID:      2112
    Task Category: Exchange VSS Writer
    Level:         Error
    Keywords:      Classic
    User:          N/A
    Computer:      Location1-Exc1-MB1
    Description: The Microsoft Exchange Replication service VSS Writer instance 1ab7d204-609a-4aea-b0a7-70afb0db38de failed with error code 80070020 when preparing for a backup of database 'DB012'.
    Followed by
    Log Name:      Application
    Source:        MSExchangeRepl
    Date:         
    01.10.2012 03:33:06
    Event ID:      2024
    Task Category: Exchange VSS Writer
    Level:         Error
    Keywords:      Classic
    User:         
    N/A
    Computer:      Location1-Exc1-MB1
    Description:
    The Microsoft Exchange Replication service VSS Writer (Instance 42916d80-36c1-4f73-86d0-596d30226349) failed with error 80070020 when preparing for a backup.
    The backup Application - Symantec Backup Exec 2010 R3 – states, this error
    Snapshot provider error (0xE000FED1): A failure occurred querying the Writer status.
    Check the Windows Event Viewer for details.
    Writer Name: Exchange Server, Writer ID: {76FE1AC4-15F7-4BCD-987E-8E1ACB462FB7}, Last error: The VSS Writer failed, but the operation can be retried (0x800423f3), State: Stable (1).
    Symatec suggests within http://www.symantec.com/business/support/index?page=content&id=TECH184095
    to restart the MS Exchange Replication Service – BUT the mentioned eventID
    8229 isn´t present on any of the both Mailboxservers.
    The affected Database is active on Location2-Exc1-Mb1 Server and in an overall healthy state. I found during my research, that below Location2-Exc1-Mb1 Server, there are not removed shadow copies present!
    This confuses me, since all Backups are normally taken from the passive copy of a Database.
    So my questions to the board are:
    * Does anyone is facing similar issues?
    * Can someone explain why snapshots are present on the Mailboxserver hosting the Active Database, whilst the errors are logged on the passive one?
    -          * Does someone know the conditions, why shadows copies remain and
    aren´t removed in a proper manner?
    What can cause the circumstance, that only 1 DB is facing such issues?
    Any suggestion is welcome!
    BR
    Markus

    Hi Lenora,
    I´ve encreases VSS / Exchange Backup Log levels to expert, before starting
    those things i´ve all tried now:
    - Backup from passive DB (forced within Symantec Backup Exec)
    - Backup from active DB (forced within Symantec Backup Exec)
    - Backup from passive DB without GRT enabled (forced within Symantec Backup Exec)
    - Backup from active DB without GRT enabled(forced within Symantec Backup Exec)
    All those attempts failed.
    But brought some more details - the backup against the active DB states, that there is still a backup in progress and therefore this backup is cancelled by VSS.
    The Solution was, that i´ve needed to restart the Exchange Replication Service on the Mailbox Server hosting the passive DB.
    Backups are working again on all DBs!
    THX for your replys.
    Best regards
    Markus

  • Stock variance report Crashes with error code REP-56048

    SR : 6990718.992
    gtcr : http://qmon.oraclecorp.com/qmon3/quickpicks.pl?t=t&q=6990718.992
    Problem Statement : When the user is trying to generate report for Stock variance report from Oracle Retail Merchandising System the report crashes with error code REP-56048.
    The steps to reproduce are specific to Oracle Retail Merchandising system application and hence I have not mentioned here.
    The REP-56048 error seems to be generic. Could you please advise me on this issue.
    Thanks & Regards,
    Sameer

    You can review the following Oracle Metalink Document;
    Comprehensive REP-56048 Troubleshooting and Overview Guide: Doc ID: Note:285281.1
    https://metalink.oracle.com/metalink/plsql/f?p=130:14:88153902823984055::::p14_database_id,p14_docid,p14_show_header,p14_show_help,p14_black_frame,p14_font:NOT,285281.1,1,1,1,helvetica
    Hope it would be useful.
    Adith

  • Failed to Open FR report With Error code 500 - 'unable to process request'

    I am running a load test against PBCS service. The service is load-balanced with 2 managed servers : EPMServer0 and EPMServer1
    When I put the loads with 60 VUs -- all visiting FR reports, the service runs without error. But when the VU# increased to 90, it began to respond with Error code 500  - 'unable to process request'.
    I tried to correlate the FRLogging logs to the errors, and found during the time those error happens, there are logs like this:
    >>>>>>>>>>>>>>>>>>>>>>>>>>
    [2013-09-27T05:21:29.325+00:00] [EPMServer0] [WARNING] [00365] [oracle.EPMFR.core] [tid: [ACTIVE].ExecuteThread: '5' for queue: 'weblogic.kernel.Default (self-tuning)'] [userId: sysname50134114.PerfUser0439] [ecid: 004tpQ^VFHT7m3RLIYDCif0007a30002bD,0:2:1:1] [APP: FINANCIALREPORTING#11.1.2.0] [SRC_CLASS: com.hyperion.reporting.connection.UserConnection] [SRC_METHOD: openConnection] User authentication information is invalid. Unable to connect to datasource.[[
    com.hyperion.reporting.util.HyperionReportException: Error connecting to database connection Vision:Plan1: Failed to sync with user provisioning.com.hyperion.planning.HspRuntimeException
            at com.hyperion.reporting.connection.UserConnection.openConnection(Unknown Source)
            at com.hyperion.reporting.connection.UserConnection.openConnection(Unknown Source)
            at com.hyperion.reporting.connection.UserConnection.<init>(Unknown Source)
            at com.hyperion.reporting.connection.ConnectionManager.getConnection(Unknown Source)
            at com.hyperion.reporting.connection.ConnectionManager.getCube(Unknown Source)
            at com.hyperion.reporting.connection.ConnectionManager.getCube(Unknown Source)
            at com.hyperion.reporting.webviewer.WebDynamicReport.validateDatasources(Unknown Source)
        at jsp_servlet._modules._com._hyperion._reporting._web._reportviewer.__hrhtmlreport._jspService(__hrhtmlreport.java:1999)
            at weblogic.servlet.jsp.JspBase.service(JspBase.java:34)
            at weblogic.servlet.internal.StubSecurityHelper$ServletServiceAction.run(StubSecurityHelper.java:227)
            at weblogic.servlet.internal.StubSecurityHelper.invokeServlet(StubSecurityHelper.java:125)
            at weblogic.servlet.internal.ServletStubImpl.execute(ServletStubImpl.java:301)
            at weblogic.servlet.internal.TailFilter.doFilter(TailFilter.java:26)
            at weblogic.servlet.internal.FilterChainImpl.doFilter(FilterChainImpl.java:56)
            at com.hyperion.reporting.webviewer.HRSecurePagesFilter.needAuthentication(Unknown Source)
            at com.hyperion.reporting.webviewer.HRSecurePagesFilter.doFilter(Unknown Source)
            at weblogic.servlet.internal.FilterChainImpl.doFilter(FilterChainImpl.java:56)
            at com.hyperion.reporting.webviewer.FRClusterHelper.doFilter(Unknown Source)
    >>>>>>>>>>>>>>>>>>>>>>>>>
    It looks like the servlet failed to open the datasource connection while handling the FR requests. But there are several data sources. My questions are:
    1) Which datasource is corresponding to the issue? Is it EPMSystemRegistry?
    2) What is the recommended configuration for the connection pool max capacity setting? -- current setting for EPMSystemRegistry is 30
    3) Whether it could be a connection leak problem as only 90 concurrent end user is visiting and it failed to connect?
    Thanks,
    Ellick Lu
    Type
    JNDI Name
    Targets
    aif_datasource
    Generic
    jdbc/aif_datasource
    EPMServer
    calc_datasource
    Generic
    jdbc/calc_datasource
    EPMServer
    EPMSystemRegistry
    Generic
    jdbc/EPMSystemRegistry
    EPMServer
    odiMasterRepository
    Generic
    jdbc/odiMasterRepository
    EPMServer
    planning_datasource
    Generic
    jdbc/planning_datasource
    EPMServer
    raframework_datasource
    Generic
    jdbc/raframework_datasource
    EPMServer

    It is checking for Database connection in Workspace. Check Editing Database Connections
    Can those users login to Planning? Do they have correct security setup (I guess not)
    Regards
    Celvin
    http://www.orahyplabs.com

  • The Cluster Service function call 'ClusterResourceControl' failed with error code '1008(An attempt was made to reference a token that does not exist.)' while verifying the file path. Verify that your failover cluster is configured properly.

    I am experiencing this error with one of our cluster environment. Can anyone help me in this issue.
    The Cluster Service function call 'ClusterResourceControl' failed with error code '1008(An attempt was made to reference a token that does not exist.)' while verifying the file path. Verify that your failover cluster is configured properly.
    Thanks,
    Venu S.
    Venugopal S ----------------------------------------------------------- Please click the Mark as Answer button if a post solves your problem!

    Hi Venu S,
    Based on my research, you might encounter a known issue, please try the hotfix in this KB:
    http://support.microsoft.com/kb/928385
    Meanwhile since there is less information about this issue, before further investigation, please provide us the following information:
    The version of Windows Server you are using
    The result of SELECT @@VERSION
    The scenario when you get this error
    If anything is unclear, please let me know.
    Regards,
    Tom Li

Maybe you are looking for

  • 0HR_PY_1 Datasource: Fields not filled

    Hello to everyone! I'm afraid that I need some help from you. We are extracting HR data via 0HR_PY_1 Datasource and I have noticed that some fields are not filled by the extraction program. I've read BW Online Help about this datasource  and I have r

  • How to create a password with JTextField

    Hi, I need to create a password field on the JTabbedPane. I can create a TextField and setEchoChar to make it a password field. However it is not working well with the rest of the JComponents. Can I do this on a JTextField? I could not find the funct

  • Restore time machine backups folder or iPhoto library to get album data?

    Simply said, can I use Data Rescue or Disk Drill to restore old Time Machine backups instead of just the entire glob of files? I'm specifically looking for an iPhoto backup with albums and metadata, instead of just restoring the photos themselves. Se

  • Who do I trust, my TV or my computer screen???

    I have a final cut of a film shot in HD. The colors look good when I watch the film on my computer screen (didn't have money to color correct but did something color correction with Final Cut and it looks pretty good). The problem is: when I burn a d

  • Serial port: Input/output signal errantly combined

    I am currently in the process of using LabView to replace another user interface for a scientific instrument. LabView is connected to this instrument through a serial port.  The instrument streams 25 bytes of binary data every second to the computer.