CWA using ISE and mobility anchor

My team is trying to demo wireless guest access using CWA with an ISE server. We appear to be hitting an issue when combining this with mobility anchoring.
When we don't use a mobility anchor the authentication goes off without a hitch seemingly proving that the ISE configuration is sound. The test laptop associates and gets redirected, auths, moves to the RUN state and access to the network is granted.
When the mobility anchor is enabled, the test laptop does get redirected, authentication is successful, but the process does not fully complete, as on the foreign controller the user is in RUN state whereas on the anchor the user is still stuck at CWA required.
Now, I've read the L2 auth occurs between the foreign controller and ISE, and the L3 auth occurs between the anchor controller and ISE, but this does not appear to borne out in packet captures of the process where both parts of the auth seems to go to and from the foreign controller and ISE.
I'm curious to know if anyone else has come across this issue, or has ideas where I should be looking in the config or debugs to find the root cause.
When setting up the controllers and ISE this guide (linked below) was used and the controllers are 2504 controllers on 7.5 series software and ISE is on the latest 1.2 patches:
http://www.cisco.com/en/US/products/ps11640/products_configuration_example09186a0080bead09.shtml
To me it seems to be mobility related, but the authentication flow does seem to be off compared with what the guide says.

FOREIGN
*apfMsConnTask_4: Jan 28 23:04:59.525: 00:1e:c2:c0:96:05 Adding mobile on LWAPP AP 0c:d9:96:ba:7d:20(1)
*apfMsConnTask_4: Jan 28 23:04:59.525: 00:1e:c2:c0:96:05 Association received from mobile on BSSID 0c:d9:96:ba:7d:2f
*apfMsConnTask_4: Jan 28 23:04:59.525: 00:1e:c2:c0:96:05 Global 200 Clients are allowed to AP radio
*apfMsConnTask_4: Jan 28 23:04:59.525: 00:1e:c2:c0:96:05 Max Client Trap Threshold: 0 cur: 0
*apfMsConnTask_4: Jan 28 23:04:59.525: 00:1e:c2:c0:96:05 Rf profile 600 Clients are allowed to AP wlan
*apfMsConnTask_4: Jan 28 23:04:59.525: 00:1e:c2:c0:96:05 Applying Interface policy on Mobile, role Unassociated. Ms NAC State 0 Quarantine Vlan 0 Access Vlan 0
*apfMsConnTask_4: Jan 28 23:04:59.525: 00:1e:c2:c0:96:05 Re-applying interface policy for client
*apfMsConnTask_4: Jan 28 23:04:59.525: 00:1e:c2:c0:96:05 0.0.0.0 START (0) Changing IPv4 ACL 'none' (ACL ID 255) ===> 'none' (ACL ID 255) --- (caller apf_policy.c:2164)
*apfMsConnTask_4: Jan 28 23:04:59.525: 00:1e:c2:c0:96:05 0.0.0.0 START (0) Changing IPv6 ACL 'none' (ACL ID 255) ===> 'none' (ACL ID 255) --- (caller apf_policy.c:2185)
*apfMsConnTask_4: Jan 28 23:04:59.526: 00:1e:c2:c0:96:05 apfApplyWlanPolicy: Retaining the ACL recieved in AAA attributes 255 on mobile
*apfMsConnTask_4: Jan 28 23:04:59.526: 00:1e:c2:c0:96:05 apfApplyWlanPolicy: Apply WLAN Policy over PMIPv6 Client Mobility Type
*apfMsConnTask_4: Jan 28 23:04:59.526: 00:1e:c2:c0:96:05 In processSsidIE:4565 setting Central switched to TRUE
*apfMsConnTask_4: Jan 28 23:04:59.526: 00:1e:c2:c0:96:05 In processSsidIE:4568 apVapId = 1 and Split Acl Id = 65535
*apfMsConnTask_4: Jan 28 23:04:59.526: 00:1e:c2:c0:96:05 Applying site-specific Local Bridging override for station 00:1e:c2:c0:96:05 - vapId 1, site 'AP-Group-CHEC.default', interface 'management'
*apfMsConnTask_4: Jan 28 23:04:59.526: 00:1e:c2:c0:96:05 Applying Local Bridging Interface Policy for station 00:1e:c2:c0:96:05 - vlan 84, interface id 0, interface 'management'
*apfMsConnTask_4: Jan 28 23:04:59.526: 00:1e:c2:c0:96:05 processSsidIE statusCode is 0 and status is 0
*apfMsConnTask_4: Jan 28 23:04:59.526: 00:1e:c2:c0:96:05 processSsidIE ssid_done_flag is 0 finish_flag is 0
*apfMsConnTask_4: Jan 28 23:04:59.526: 00:1e:c2:c0:96:05 STA - rates (8): 140 18 152 36 176 72 96 108 0 0 0 0 0 0 0 0
*apfMsConnTask_4: Jan 28 23:04:59.526: 00:1e:c2:c0:96:05 suppRates statusCode is 0 and gotSuppRatesElement is 1
*apfMsConnTask_4: Jan 28 23:04:59.526: 00:1e:c2:c0:96:05 apfProcessAssocReq (apf_80211.c:7830) Changing state for mobile 00:1e:c2:c0:96:05 on AP 0c:d9:96:ba:7d:20 from Idle to AAA Pending
*apfMsConnTask_4: Jan 28 23:04:59.526: 00:1e:c2:c0:96:05 Scheduling deletion of Mobile Station: (callerId: 20) in 10 seconds
*radiusTransportThread: Jan 28 23:04:59.550: 00:1e:c2:c0:96:05 Username entry (00-1E-C2-C0-96-05) created for mobile, length = 253
*radiusTransportThread: Jan 28 23:04:59.550: 00:1e:c2:c0:96:05 Username entry (00-1E-C2-C0-96-05) created in mscb for mobile, length = 253
*apfReceiveTask: Jan 28 23:04:59.550: 00:1e:c2:c0:96:05 Received SGT for this Client.
*apfReceiveTask: Jan 28 23:04:59.550: 00:1e:c2:c0:96:05 Redirect URL received for client from RADIUS. Client will be moved to WebAuth_Reqd state to facilitate redirection. Skip web-auth Flag = 0
*apfReceiveTask: Jan 28 23:04:59.550: 00:1e:c2:c0:96:05 Resetting web IPv4 acl from 255 to 255
*apfReceiveTask: Jan 28 23:04:59.550: 00:1e:c2:c0:96:05 Resetting web IPv4 Flex acl from 65535 to 65535
*apfReceiveTask: Jan 28 23:04:59.550: 00:1e:c2:c0:96:05 Applying Interface policy on Mobile, role Unassociated. Ms NAC State 2 Quarantine Vlan 0 Access Vlan 84
*apfReceiveTask: Jan 28 23:04:59.550: 00:1e:c2:c0:96:05 Re-applying interface policy for client
*apfReceiveTask: Jan 28 23:04:59.550: 00:1e:c2:c0:96:05 0.0.0.0 START (0) Changing IPv4 ACL 'none' (ACL ID 255) ===> 'none' (ACL ID 255) --- (caller apf_policy.c:2164)
*apfReceiveTask: Jan 28 23:04:59.550: 00:1e:c2:c0:96:05 0.0.0.0 START (0) Changing IPv6 ACL 'none' (ACL ID 255) ===> 'none' (ACL ID 255) --- (caller apf_policy.c:2185)
*apfReceiveTask: Jan 28 23:04:59.550: 00:1e:c2:c0:96:05 apfApplyWlanPolicy: Retaining the ACL recieved in AAA attributes 0 on mobile
*apfReceiveTask: Jan 28 23:04:59.551: 00:1e:c2:c0:96:05 apfApplyWlanPolicy: Apply WLAN Policy over PMIPv6 Client Mobility Type
*apfReceiveTask: Jan 28 23:04:59.551: 00:1e:c2:c0:96:05 Inserting AAA Override struct for mobile
MAC: 00:1e:c2:c0:96:05, source 2
*apfReceiveTask: Jan 28 23:04:59.551: 00:1e:c2:c0:96:05 0.0.0.0 START (0) Initializing policy
*apfReceiveTask: Jan 28 23:04:59.551: 00:1e:c2:c0:96:05 0.0.0.0 START (0) Change state to AUTHCHECK (2) last state START (0)
*apfReceiveTask: Jan 28 23:04:59.551: 00:1e:c2:c0:96:05 0.0.0.0 AUTHCHECK (2) Change state to L2AUTHCOMPLETE (4) last state AUTHCHECK (2)
*apfReceiveTask: Jan 28 23:04:59.551: 00:1e:c2:c0:96:05 Not Using WMM Compliance code qosCap 00
*apfReceiveTask: Jan 28 23:04:59.551: 00:1e:c2:c0:96:05 0.0.0.0 L2AUTHCOMPLETE (4) Plumbed mobile LWAPP rule on AP 0c:d9:96:ba:7d:20 vapId 1 apVapId 1 flex-acl-name:
*apfReceiveTask: Jan 28 23:04:59.551: 00:1e:c2:c0:96:05 0.0.0.0 L2AUTHCOMPLETE (4) Change state to DHCP_REQD (7) last state L2AUTHCOMPLETE (4)
*apfReceiveTask: Jan 28 23:04:59.551: 00:1e:c2:c0:96:05 apfMsAssoStateInc
*apfReceiveTask: Jan 28 23:04:59.551: 00:1e:c2:c0:96:05 apfPemAddUser2 (apf_policy.c:333) Changing state for mobile 00:1e:c2:c0:96:05 on AP 0c:d9:96:ba:7d:20 from AAA Pending to Associated
*apfReceiveTask: Jan 28 23:04:59.551: 00:1e:c2:c0:96:05 apfPemAddUser2:session timeout forstation 00:1e:c2:c0:96:05 - Session Tout 1800, apfMsTimeOut '1800' and sessionTimerRunning flag is 0
*apfReceiveTask: Jan 28 23:04:59.551: 00:1e:c2:c0:96:05 Scheduling deletion of Mobile Station: (callerId: 49) in 1800 seconds
*apfReceiveTask: Jan 28 23:04:59.551: 00:1e:c2:c0:96:05 Func: apfPemAddUser2, Ms Timeout = 1800, Session Timeout = 1800
*apfReceiveTask: Jan 28 23:04:59.551: 00:1e:c2:c0:96:05 Sending Assoc Response to station on BSSID 0c:d9:96:ba:7d:2f (status 0) ApVapId 1 Slot 1
*apfReceiveTask: Jan 28 23:04:59.551: 00:1e:c2:c0:96:05 apfProcessRadiusAssocResp (apf_80211.c:3066) Changing state for mobile 00:1e:c2:c0:96:05 on AP 0c:d9:96:ba:7d:20 from Associated to Associated
*DHCP Socket Task: Jan 28 23:04:59.567: 00:1e:c2:c0:96:05 DHCP received op BOOTREQUEST (1) (len 308,vlan 84, port 13, encap 0xec03)
*DHCP Socket Task: Jan 28 23:04:59.567: 00:1e:c2:c0:96:05 DHCP (encap type 0xec03) mstype 0ff:ff:ff:ff:ff:ff
*DHCP Socket Task: Jan 28 23:04:59.567: 00:1e:c2:c0:96:05 DHCP dropping packet due to ongoing mobility handshake exchange, (siaddr 0.0.0.0, mobility state = 'apfMsMmQueryRequested'
*DHCP Socket Task: Jan 28 23:05:01.523: 00:1e:c2:c0:96:05 DHCP received op BOOTREQUEST (1) (len 308,vlan 84, port 13, encap 0xec03)
*DHCP Socket Task: Jan 28 23:05:01.523: 00:1e:c2:c0:96:05 DHCP (encap type 0xec03) mstype 0ff:ff:ff:ff:ff:ff
*DHCP Socket Task: Jan 28 23:05:01.523: 00:1e:c2:c0:96:05 DHCP dropping packet due to ongoing mobility handshake exchange, (siaddr 0.0.0.0, mobility state = 'apfMsMmQueryRequested'
*mmMaListen: Jan 28 23:05:02.362: 00:1e:c2:c0:96:05 0.0.0.0 DHCP_REQD (7) State Update from Mobility-Incomplete to Mobility-Complete, mobility role=ExpForeign, client state=APF_MS_STATE_ASSOCIATED
*mmMaListen: Jan 28 23:05:02.362: 00:1e:c2:c0:96:05 apfMsRunStateInc
*mmMaListen: Jan 28 23:05:02.362: 00:1e:c2:c0:96:05 0.0.0.0 DHCP_REQD (7) Change state to RUN (20) last state DHCP_REQD (7)
*mmMaListen: Jan 28 23:05:02.362: 00:1e:c2:c0:96:05 0.0.0.0 RUN (20) Reached PLUMBFASTPATH: from line 5793
*mmMaListen: Jan 28 23:05:02.362: 00:1e:c2:c0:96:05 0.0.0.0 RUN (20) Adding Fast Path rule
type = Airespace AP Client
on AP 0c:d9:96:ba:7d:20, slot 1, interface = 13, QOS = 0
IPv4 ACL ID = 255, IPv6 ACL ID = 255,
*mmMaListen: Jan 28 23:05:02.362: 00:1e:c2:c0:96:05 0.0.0.0 RUN (20) Fast Path rule (contd...) 802.1P = 0, DSCP = 0, TokenID = 15206 Local Bridging Vlan = 84, Local Bridging intf id = 0
*mmMaListen: Jan 28 23:05:02.363: 00:1e:c2:c0:96:05 0.0.0.0 RUN (20) Successfully plumbed mobile rule (IPv4 ACL ID 255, IPv6 ACL ID 255, L2 ACL ID 255)
*pemReceiveTask: Jan 28 23:05:02.364: 00:1e:c2:c0:96:05 Set bi-dir guest tunnel for 00:1e:c2:c0:96:05 as in Export Foreign role
*pemReceiveTask: Jan 28 23:05:02.364: 00:1e:c2:c0:96:05 0.0.0.0 Added NPU entry of type 1, dtlFlags 0x4
*pemReceiveTask: Jan 28 23:05:02.364: 00:1e:c2:c0:96:05 Skip Foreign / Export Foreign Client IP 0.0.0.0 plumbing in FP SCB
*DHCP Socket Task: Jan 28 23:05:03.869: 00:1e:c2:c0:96:05 DHCP received op BOOTREQUEST (1) (len 308,vlan 84, port 13, encap 0xec03)
*DHCP Socket Task: Jan 28 23:05:03.869: 00:1e:c2:c0:96:05 DHCP (encap type 0xec03) mstype 0ff:ff:ff:ff:ff:ff
*DHCP Socket Task: Jan 28 23:05:03.869: 00:1e:c2:c0:96:05 DHCP processing DHCP REQUEST (3)
*DHCP Socket Task: Jan 28 23:05:03.869: 00:1e:c2:c0:96:05 DHCP   op: BOOTREQUEST, htype: Ethernet, hlen: 6, hops: 0
*DHCP Socket Task: Jan 28 23:05:03.869: 00:1e:c2:c0:96:05 DHCP   xid: 0xafea6bc9 (2951375817), secs: 5, flags: 0
*DHCP Socket Task: Jan 28 23:05:03.869: 00:1e:c2:c0:96:05 DHCP   chaddr: 00:1e:c2:c0:96:05
*DHCP Socket Task: Jan 28 23:05:03.869: 00:1e:c2:c0:96:05 DHCP   ciaddr: 0.0.0.0, yiaddr: 0.0.0.0
*DHCP Socket Task: Jan 28 23:05:03.869: 00:1e:c2:c0:96:05 DHCP   siaddr: 0.0.0.0, giaddr: 0.0.0.0
*DHCP Socket Task: Jan 28 23:05:03.869: 00:1e:c2:c0:96:05 DHCP   requested ip: 10.130.98.8
*DHCP Socket Task: Jan 28 23:05:03.887: 00:1e:c2:c0:96:05 DHCP received op BOOTREPLY (2) (len 320,vlan 84, port 13, encap 0xec07)
*DHCP Socket Task: Jan 28 23:05:03.887: 00:1e:c2:c0:96:05 DHCP processing DHCP ACK (5)
*DHCP Socket Task: Jan 28 23:05:03.887: 00:1e:c2:c0:96:05 DHCP   op: BOOTREPLY, htype: Ethernet, hlen: 6, hops: 0
*DHCP Socket Task: Jan 28 23:05:03.887: 00:1e:c2:c0:96:05 DHCP   xid: 0xafea6bc9 (2951375817), secs: 0, flags: 0
*DHCP Socket Task: Jan 28 23:05:03.887: 00:1e:c2:c0:96:05 DHCP   chaddr: 00:1e:c2:c0:96:05
*DHCP Socket Task: Jan 28 23:05:03.887: 00:1e:c2:c0:96:05 DHCP   ciaddr: 0.0.0.0, yiaddr: 10.130.98.8
*DHCP Socket Task: Jan 28 23:05:03.887: 00:1e:c2:c0:96:05 DHCP   siaddr: 10.30.4.173, giaddr: 0.0.0.0
*DHCP Socket Task: Jan 28 23:05:03.887: 00:1e:c2:c0:96:05 DHCP   server id: 1.1.1.2 rcvd server id: 1.1.1.2
*DHCP Socket Task: Jan 28 23:05:03.887: 00:1e:c2:c0:96:05 10.130.98.8 RUN (20) DHCP Address Re-established
*DHCP Socket Task: Jan 28 23:05:03.887: 00:1e:c2:c0:96:05 10.130.98.8 RUN (20) Reached PLUMBFASTPATH: from line 6978
*DHCP Socket Task: Jan 28 23:05:03.887: 00:1e:c2:c0:96:05 10.130.98.8 RUN (20) Replacing Fast Path rule
type = Airespace AP Client
on AP 0c:d9:96:ba:7d:20, slot 1, interface = 13, QOS = 0
IPv4 ACL ID = 255, IPv6 ACL ID
*DHCP Socket Task: Jan 28 23:05:03.887: 00:1e:c2:c0:96:05 10.130.98.8 RUN (20) Fast Path rule (contd...) 802.1P = 0, DSCP = 0, TokenID = 15206 Local Bridging Vlan = 84, Local Bridging intf id = 0
*DHCP Socket Task: Jan 28 23:05:03.888: 00:1e:c2:c0:96:05 10.130.98.8 RUN (20) Successfully plumbed mobile rule (IPv4 ACL ID 255, IPv6 ACL ID 255, L2 ACL ID 255)
*DHCP Socket Task: Jan 28 23:05:03.888: 00:1e:c2:c0:96:05 Assigning Address 10.130.98.8 to mobile
*DHCP Socket Task: Jan 28 23:05:03.888: 00:1e:c2:c0:96:05 DHCP success event for client. Clearing dhcp failure count for interface management.
*DHCP Socket Task: Jan 28 23:05:03.888: 00:1e:c2:c0:96:05 DHCP success event for client. Clearing dhcp failure count for interface management.
*DHCP Socket Task: Jan 28 23:05:03.888: 00:1e:c2:c0:96:05 DHCP successfully bridged packet to STA
*pemReceiveTask: Jan 28 23:05:03.889: 00:1e:c2:c0:96:05 Set bi-dir guest tunnel for 00:1e:c2:c0:96:05 as in Export Foreign role
*pemReceiveTask: Jan 28 23:05:03.889: 00:1e:c2:c0:96:05 10.130.98.8 Added NPU entry of type 1, dtlFlags 0x4
*pemReceiveTask: Jan 28 23:05:03.890: 00:1e:c2:c0:96:05 Skip Foreign / Export Foreign Client IP 10.130.98.8 plumbing in FP SCB
*apfReceiveTask: Jan 28 23:05:18.716: 00:1e:c2:c0:96:05 Received SGT for this Client.
*apfReceiveTask: Jan 28 23:05:18.716: 00:1e:c2:c0:96:05 Resetting web IPv4 acl from 0 to 255
*apfReceiveTask: Jan 28 23:05:18.716: 00:1e:c2:c0:96:05 Resetting web IPv4 Flex acl from 65535 to 65535
*apfReceiveTask: Jan 28 23:05:18.716: 00:1e:c2:c0:96:05 AAA redirect is NULL. Skipping Web-auth for Radius NAC enabled WLAN.
*apfReceiveTask: Jan 28 23:05:18.716: 00:1e:c2:c0:96:05 apfApplyWlanPolicy: Retaining the ACL recieved in AAA attributes 255 on mobile
*apfReceiveTask: Jan 28 23:05:18.716: 00:1e:c2:c0:96:05 apfApplyWlanPolicy: Apply WLAN Policy over PMIPv6 Client Mobility Type
*apfReceiveTask: Jan 28 23:05:18.716: 00:1e:c2:c0:96:05 Inserting AAA Override struct for mobile
MAC: 00:1e:c2:c0:96:05, source 2
*apfReceiveTask: Jan 28 23:05:18.717: 00:1e:c2:c0:96:05 Setting session timeout 3600 on mobile 00:1e:c2:c0:96:05
*apfReceiveTask: Jan 28 23:05:18.717: 00:1e:c2:c0:96:05 Session Timeout is 3600 - starting session timer for the mobile
*apfReceiveTask: Jan 28 23:05:18.717: 00:1e:c2:c0:96:05 Applying cached RADIUS Override values for mobile 00:1e:c2:c0:96:05 (caller pem_api.c:2307)
*apfReceiveTask: Jan 28 23:05:18.717: 00:1e:c2:c0:96:05 Setting session timeout 3600 on mobile 00:1e:c2:c0:96:05
*apfReceiveTask: Jan 28 23:05:18.717: 00:1e:c2:c0:96:05 Session Timeout is 3600 - starting session timer for the mobile
*apfReceiveTask: Jan 28 23:05:18.717: 00:1e:c2:c0:96:05 10.130.98.8 RUN (20) Applied RADIUS override policy
*apfReceiveTask: Jan 28 23:05:18.717: 00:1e:c2:c0:96:05 10.130.98.8 RUN (20) Replacing Fast Path rule
type = Airespace AP Client
on AP 0c:d9:96:ba:7d:20, slot 1, interface = 13, QOS = 0
IPv4 ACL ID = 255, IPv6 ACL ID
*apfReceiveTask: Jan 28 23:05:18.717: 00:1e:c2:c0:96:05 10.130.98.8 RUN (20) Fast Path rule (contd...) 802.1P = 0, DSCP = 0, TokenID = 15206 Local Bridging Vlan = 84, Local Bridging intf id = 0
*apfReceiveTask: Jan 28 23:05:18.717: 00:1e:c2:c0:96:05 10.130.98.8 RUN (20) Successfully plumbed mobile rule (IPv4 ACL ID 255, IPv6 ACL ID 255, L2 ACL ID 255)
*apfReceiveTask: Jan 28 23:05:18.717: 00:1e:c2:c0:96:05 Not Using WMM Compliance code qosCap 00
*apfReceiveTask: Jan 28 23:05:18.717: 00:1e:c2:c0:96:05 10.130.98.8 RUN (20) Plumbed mobile LWAPP rule on AP 0c:d9:96:ba:7d:20 vapId 1 apVapId 1 flex-acl-name:
*apfReceiveTask: Jan 28 23:05:18.717: 00:1e:c2:c0:96:05 10.130.98.8 RUN (20) Change state to RUN (20) last state RUN (20)
*apfReceiveTask: Jan 28 23:05:18.717: 00:1e:c2:c0:96:05 apfMsAssoStateInc
*apfReceiveTask: Jan 28 23:05:18.717: 00:1e:c2:c0:96:05 apfPemAddUser2 (apf_policy.c:333) Changing state for mobile 00:1e:c2:c0:96:05 on AP 0c:d9:96:ba:7d:20 from AAA Pending to Associated
*apfReceiveTask: Jan 28 23:05:18.717: 00:1e:c2:c0:96:05 apfPemAddUser2:session timeout forstation 00:1e:c2:c0:96:05 - Session Tout 3600, apfMsTimeOut '1800' and sessionTimerRunning flag is 1
*apfReceiveTask: Jan 28 23:05:18.717: 00:1e:c2:c0:96:05 Scheduling deletion of Mobile Station: (callerId: 49) in 3600 seconds
*apfReceiveTask: Jan 28 23:05:18.717: 00:1e:c2:c0:96:05 Func: apfPemAddUser2, Ms Timeout = 1800, Session Timeout = 3600
*apfReceiveTask: Jan 28 23:05:18.718: 00:1e:c2:c0:96:05 Sending Assoc Response to station on BSSID 0c:d9:96:ba:7d:2f (status 0) ApVapId 1 Slot 1
*apfReceiveTask: Jan 28 23:05:18.718: 00:1e:c2:c0:96:05 apfProcessRadiusAssocResp (apf_80211.c:3066) Changing state for mobile 00:1e:c2:c0:96:05 on AP 0c:d9:96:ba:7d:20 from Associated to Associated
*pemReceiveTask: Jan 28 23:05:18.720: 00:1e:c2:c0:96:05 Set bi-dir guest tunnel for 00:1e:c2:c0:96:05 as in Export Foreign role
*pemReceiveTask: Jan 28 23:05:18.720: 00:1e:c2:c0:96:05 10.130.98.8 Added NPU entry of type 1, dtlFlags 0x4

Similar Messages

CWA with ISE and 5760

Hi,
we have an ISE 1.2 (Patch 5), two 5760 Controllers (3.3), one acting as Primary Controller (named WC7) for the APs and the other as Guest Anchor (named WC5).
I have trouble with the CWA. The Guest is redirected and enters the correct credentials. After that, the CoA fails with error-cause(272) 4 Session Context Not Found. I have no idea why....
aaa authentication login Webauth_ISE group ISE
aaa authorization network cwa_macfilter group ISE
aaa authorization network Webauth_ISE group ISE
aaa accounting network ISE start-stop group ISE
aaa server radius dynamic-author
client 10.232.127.13 server-key 0 blabla
auth-type any
radius-server attribute 6 on-for-login-auth
radius-server attribute 31 send nas-port-detail mac-only
wlan test4guests 18 test4guests
aaa-override
accounting-list ISE
client vlan 1605
no exclusionlist
mac-filtering cwa_macfilter
mobility anchor
nac
no security wpa
no security wpa akm dot1x
no security wpa wpa2
no security wpa wpa2 ciphers aes
security dot1x authentication-list Webauth_ISE
no shutdown
wc5# debug aaa coa
Feb 27 12:19:08.444: COA: 10.232.127.13 request queued
Feb 27 12:19:08.444: RADIUS: authenticator CC 33 26 77 56 96 30 58 - BC 99 F3 1A 3C 61 DC F4
Feb 27 12:19:08.444: RADIUS: NAS-IP-Address      [4]   6   10.232.127.11
Feb 27 12:19:08.444: RADIUS: Calling-Station-Id [31] 14 "40f308c3c53d"
Feb 27 12:19:08.444: RADIUS: Event-Timestamp     [55] 6   1393503547
Feb 27 12:19:08.444: RADIUS: Message-Authenticato[80] 18
Feb 27 12:19:08.444: RADIUS:   22 F8 CF 1C 61 F3 F9 42 01 E4 36 77 9C 9B CC 56            [ "aB6wV]
Feb 27 12:19:08.444: RADIUS: Vendor, Cisco       [26] 41
Feb 27 12:19:08.444: RADIUS:   Cisco AVpair       [1]   35 "subscriber:command=reauthenticate"
Feb 27 12:19:08.444: RADIUS: Vendor, Cisco       [26] 43
Feb 27 12:19:08.444: RADIUS:   Cisco AVpair       [1]   37 "subscriber:reauthenticate-type=last"
Feb 27 12:19:08.444: RADIUS: Vendor, Cisco       [26] 49
Feb 27 12:19:08.444: RADIUS:   Cisco AVpair       [1]   43 "audit-session-id=0aea2001530f2e1e000003c6"
Feb 27 12:19:08.444: COA: Message Authenticator decode passed
Feb 27 12:19:08.444: ++++++ CoA Attribute List ++++++
Feb 27 12:19:08.444: 92FB84A0 0 00000001 nas-ip-address(600) 4 10.232.127.11
Feb 27 12:19:08.444: 92FB87EC 0 00000081 formatted-clid(37) 12 40f308c3c53d
Feb 27 12:19:08.444: 92FB8820 0 00000001 Event-Timestamp(445) 4 1393503547(530F2D3B)
Feb 27 12:19:08.444: 92FB8854 0 00000001 reauthenticate-type(756) 4 last
Feb 27 12:19:08.444: 92FB8888 0 00000081 audit-session-id(819) 24 0aea2001530f2e1e000003c6
Feb 27 12:19:08.444: 92FB88BC 0 00000081 ssg-command-code(490) 1 32
Feb 27 12:19:08.444:
Feb 27 12:19:08.444: ++++++ Received CoA response Attribute List ++++++
Feb 27 12:19:08.444: 92FB84A0 0 00000001 nas-ip-address(600) 4 10.232.127.11
Feb 27 12:19:08.444: 92FB87EC 0 00000081 formatted-clid(37) 12 40f308c3c53d
Feb 27 12:19:08.444: 92FB8820 0 00000001 Event-Timestamp(445) 4 1393503547(530F2D3B)
Feb 27 12:19:08.444: 92FB8854 0 00000001 reauthenticate-type(756) 4 last
Feb 27 12:19:08.444: 92FB8888 0 00000081 audit-session-id(819) 24 0aea2001530f2e1e000003c6
Feb 27 12:19:08.444: 92FB88BC 0 00000081 ssg-command-code(490) 1 32
Feb 27 12:19:08.444: 92FB88F0 0 00000002 error-cause(272) 4 Session Context Not Found
Feb 27 12:19:08.444:
wc5#

Reason for this are two bugs which prevent this from working:
https://tools.cisco.com/bugsearch/bug/CSCul83594
https://tools.cisco.com/bugsearch/bug/CSCun38344
This is embarrassing because this is a really common scenario. QA anyone?
So, with ISE and 5760 CWA is not working at this time.

CWA on ISE and switches

I was able to configure the CWA on the switch and Cisco ISE. It is working as expected. I followed the guide on the link bellow.
http://www.cisco.com/en/US/products/ps11640/products_configuration_example09186a0080ba6514.shtml
I only have one question. I try to understand why ACL must be configured on the port on the switch. Guide uses ACL with name webauth which permit all traffic. If port is authorized it receives dACL from ISE, otherwise port is in unauthorize state and denies all traffic.
interface GigabitEthernet1/0/12
description ISE1 - dot1x clients - UCS Eth0
switchport access vlan 100
switchport mode access
ip access-group webauth in
authentication order mab
authentication priority mab
authentication port-control auto
mab
spanning-tree portfast
end
ip access-list extended webauth
permit ip any any

Why ACL must be configured on the port on the switch
Question:
I only have one question. I try to understand why ACL must be configured on the port on the switch. Guide uses ACL with name webauth which permit all traffic. If port is authorized it receives dACL from ISE, otherwise port is in unauthorize state and denies all traffic.
What is Web Authentication?
Web authentication is opposed to local web authentication, which is the usual web authentication on the switch itself. In that system, upon dot1x/mab failure, the switch wills failover to the webauth profile and will redirect client traffic to a web page on the switch.
Role of ACL:
The redirectACL sent back with the central webauth profile determines which traffic (HTT or HTTPS) is redirected to the ISE. The downloadable ACL allows you to define what traffic is allowed. You should typically allow for DNS, HTTP(S), and 8443 and deny the rest. Otherwise, the switch redirects HTTP traffic but allows other protocols.
Port ACLs
Port ACLs are ACLs that are applied to Layer 2 interfaces on a switch. Port ACLs are supported only on physical interfaces and not on EtherChannel interfaces and can be applied only on interfaces in the inbound direction. These access lists are supported:
•Standard IP access lists using source addresses
•Extended IP access lists using source and destination addresses and optional protocol type information
•MAC extended access lists using source and destination MAC addresses and optional protocol type information
The switch examines ACLs associated with all inbound features configured on a given interface and permits or denies packet forwarding based on how the packet matches the entries in the ACL. In this way, ACLs control access to a network or to part of a network. Figure is an example of using port ACLs to control access to a network when all workstations are in the same VLAN. ACLs applied at the Layer 2 input would allow Host A to access the Human Resources network, but prevent Host B from accessing the same network. Port ACLs can only be applied to Layer 2 interfaces in the inbound direction.
Figure 31-1 Using ACLs to Control Traffic to a Network
When you apply a port ACL to a trunk port, the ACL filters traffic on all VLANs present on the trunk port. When you apply a port ACL to a port with voice VLAN, the ACL filters traffic on both data and voice VLANs.
With port ACLs, you can filter IP traffic by using IP access lists and non-IP traffic by using MAC addresses. You can filter both IP and non-IP traffic on the same Layer 2 interface by applying both an IP access list and a MAC access list to the interface.
For More information, please check
http://www.cisco.com/en/US/docs/switches/lan/catalyst2960/software/release/12.2_55_se/configuration/guide/swacl.html#wp1715468

SSO for BYOD's using ISE and Ironport

A customer would like to allow users access to a BYOD WLAN on a Cisco WLC and grant them content filtering on a Cisco Ironport based on the login they enter into the WLC web authentication form. Is this possible?
If not, would ISE make this possible?
Ultimately, they'd liek to NOT have to enter credentials twice - once for wireless auth., once for Ironport auth. - and grant users the appropirate filtering policies. My thought was that ISE might allow this through the use of user certificates and/or automatic supplicant provisioning.

someone find a solution ?

WLC 7.5 Sleeping clients with ISE and Central WEB Auth(CWA)

Hi there,
Is it possibe to use sleeping clients when using ISE and CWA?
I was thinking of enabling layer3 auth with web auth on mac auth failure, but will that work with CWA?
Or is the only solution to use LWA?

Controller-> General-> User Idle Timeout (seconds) = 50 000 sec.
And your users will be connected all this time even if they going in sleepmode
be carefull with CPU loading

Simple explanation of what is happening with iWeb and Mobile Me. Can anyone explain this simply and if our existing web site can be hosted elsewhere, if so can it still be updated using iWeb. Any advice very welcome

We have a website that has run successfully using iWeb and Mobile me. We understand Mobile Me is being discontinued from June. From this forum it seems iWeb also is not being supported any more. So can the existing site be hosted successfully with another provider or is it best to start again. If so any advice on options would be very welcome;
Thanks
PB

For the most part if you just get a new webhost you can continue to run with iWeb. Since you are still running Tiger iWeb should work just fine for you. You will simply need to publish your website to a folder or with the built in FTP in iWeb. Apple has simply quit updating iWeb & there will come a day when iWeb quits working in the later OS's whatever kitty comes after Lion.
Here's a link to who I use for Hosting:
http://jeffnitschke.com/wordpress/?p=84

How to Sync clock on WLC ISE and AD

Hi there,
I am stuck in NTP, deployed WLC CWA using ISE that is integrated with AD. I tried using AD as NTP source but no luck(universal fact that Cisco uses NTP where as Microsoft uses SNTP).
The issue is, if time is not synced between WLC, ISE and AD; web redirection stopped working and no authentication takes place.
I tried installting Meinbergglobal NTP software to distribute time to my Cisco devices. It does work with Cisco devices but it acts as master and do not sync its own time with AD.
I am trying to figure out a way to sync Cisco with Microsoft, is there any way in this world to do so???
Please help..
Thanks in advance

You mean I should sync AD and all my cisco devices with global NTP server?
Yes and no. If you know your network well, doing this is a pain in the proverbial backside because you have to open firewall rules to everyone going out to the global NTP server.
The smart thing to do is what George has described. You select a few (between two to four) to go out to the internet to synchronize. Normally I would nominate our core routers do this. Next, all our distribution switches and core switches synchronize to our core routers. All our servers, PCs, printers, WLC, switches sychronize to our distro switches.

ISE and RSA token groups

We have wireless network using ISE and RSA to do the authenticaiton. There are two groups of RSA token users, one is with username
Axxxx, the other Bxxxx.
Now we try to differ the authentications for the two group. One permit, the other deny.
I am wondering whether the ISE can do this or not.
thanks,
Han

ISE 1.2 should work with RSA 8.1. Please do try it in a lab setup would probably qualify it as part of ISE 1.3.

ISE and WLC

Dear friends,
We are using ISE and WLC integrity in our network, we have Corporate and Guest SSID, we configured it but client cant connect to this ssid and cant be authenticated, please see attached files and tell me if i done something wrong in configuration of WLC
10.10.17.201 is ISE
Thank you for attention

Hi,
After viewing the Trap logs it seems you have checked on validate machine.
On the client side, make sure you don't check validate machine and then try.

Flex 4.5 problem using image in Mobile Application (Android)

I have a problem using flex and mobile application...
I have an image with path = "/mnt/sdcard/images/20120202172020990.jpg"
Simply using
<s:Image id="image" source="/mnt/sdcard/images/20120202172020990.jpg" />
Get me an empty image on device, still using it on computer (desktop build / debug) it works fine...
I have enabled every kind of permission in the app.xml
Why I got this error?

I actually solved the problem using:
image.source = File.desktopDirectory.resolvePath(file_name).url;
using instead this one it will work only under windows...
image.source = File.desktopDirectory.resolvePath(file_name).nativePath;
I don't know if it's a bug or whatelse, but I think that the source property of Image passing a filename that start with / (/ is root for unix based OS, android, linux, ios, etc), will take is as a relative path instead of complete path...

PDA and Mobile

hi all
One of our client want to develop application using Forms and reports and keeing them on application server on intranet. the data in the application is real time data. He want to use PDACS and Mobile to view the alerts and data from the database. Does any one did similar work... is so can u share how ??

Forms does not run on those devices (PDAs or other mobile devices). You should ask your question on another forum. Try the iAS forum.
Regards,
Robin Zimmermann
Forms Product Management

Wireless guest access with CWA and ISE using mobility anchor

My team is trying to demo wireless guest access using CWA with an ISE server. We appear to be hitting an issue when combining this with mobility anchoring.
When we don't use a mobility anchor the authentication goes off without a hitch seemingly proving that the ISE configuration is sound. The test laptop associates and gets redirected, auths, moves to the RUN state and access to the network is granted.
When the mobility anchor is enabled, the test laptop does get redirected, authentication is successful, but the process does not fully complete, as on the foreign controller the user is in RUN state whereas on the anchor the user is still stuck at CWA required.
Now, I've read the L2 auth occurs between the foreign controller and ISE, and the L3 auth occurs between the anchor controller and ISE, but this does not appear to borne out in packet captures of the process where both parts of the auth seems to go to and from the foreign controller and ISE.
I'm curious to know if anyone else has come across this issue, or has ideas where I should be looking in the config or debugs to find the root cause.
When setting up the controllers and ISE this guide (linked below) was used and the controllers are 2504 controllers on 7.5 series software and ISE is on the latest 1.2 patches:
http://www.cisco.com/en/US/products/ps11640/products_configuration_example09186a0080bead09.shtml
To me it seems to be mobility related, but the authentication flow does seem to be off compared with what the guide says.

FOREIGN
*apfMsConnTask_4: Jan 28 23:04:59.525: 00:1e:c2:c0:96:05 Adding mobile on LWAPP AP 0c:d9:96:ba:7d:20(1)
*apfMsConnTask_4: Jan 28 23:04:59.525: 00:1e:c2:c0:96:05 Association received from mobile on BSSID 0c:d9:96:ba:7d:2f
*apfMsConnTask_4: Jan 28 23:04:59.525: 00:1e:c2:c0:96:05 Global 200 Clients are allowed to AP radio
*apfMsConnTask_4: Jan 28 23:04:59.525: 00:1e:c2:c0:96:05 Max Client Trap Threshold: 0 cur: 0
*apfMsConnTask_4: Jan 28 23:04:59.525: 00:1e:c2:c0:96:05 Rf profile 600 Clients are allowed to AP wlan
*apfMsConnTask_4: Jan 28 23:04:59.525: 00:1e:c2:c0:96:05 Applying Interface policy on Mobile, role Unassociated. Ms NAC State 0 Quarantine Vlan 0 Access Vlan 0
*apfMsConnTask_4: Jan 28 23:04:59.525: 00:1e:c2:c0:96:05 Re-applying interface policy for client
*apfMsConnTask_4: Jan 28 23:04:59.525: 00:1e:c2:c0:96:05 0.0.0.0 START (0) Changing IPv4 ACL 'none' (ACL ID 255) ===> 'none' (ACL ID 255) --- (caller apf_policy.c:2164)
*apfMsConnTask_4: Jan 28 23:04:59.525: 00:1e:c2:c0:96:05 0.0.0.0 START (0) Changing IPv6 ACL 'none' (ACL ID 255) ===> 'none' (ACL ID 255) --- (caller apf_policy.c:2185)
*apfMsConnTask_4: Jan 28 23:04:59.526: 00:1e:c2:c0:96:05 apfApplyWlanPolicy: Retaining the ACL recieved in AAA attributes 255 on mobile
*apfMsConnTask_4: Jan 28 23:04:59.526: 00:1e:c2:c0:96:05 apfApplyWlanPolicy: Apply WLAN Policy over PMIPv6 Client Mobility Type
*apfMsConnTask_4: Jan 28 23:04:59.526: 00:1e:c2:c0:96:05 In processSsidIE:4565 setting Central switched to TRUE
*apfMsConnTask_4: Jan 28 23:04:59.526: 00:1e:c2:c0:96:05 In processSsidIE:4568 apVapId = 1 and Split Acl Id = 65535
*apfMsConnTask_4: Jan 28 23:04:59.526: 00:1e:c2:c0:96:05 Applying site-specific Local Bridging override for station 00:1e:c2:c0:96:05 - vapId 1, site 'AP-Group-CHEC.default', interface 'management'
*apfMsConnTask_4: Jan 28 23:04:59.526: 00:1e:c2:c0:96:05 Applying Local Bridging Interface Policy for station 00:1e:c2:c0:96:05 - vlan 84, interface id 0, interface 'management'
*apfMsConnTask_4: Jan 28 23:04:59.526: 00:1e:c2:c0:96:05 processSsidIE statusCode is 0 and status is 0
*apfMsConnTask_4: Jan 28 23:04:59.526: 00:1e:c2:c0:96:05 processSsidIE ssid_done_flag is 0 finish_flag is 0
*apfMsConnTask_4: Jan 28 23:04:59.526: 00:1e:c2:c0:96:05 STA - rates (8): 140 18 152 36 176 72 96 108 0 0 0 0 0 0 0 0
*apfMsConnTask_4: Jan 28 23:04:59.526: 00:1e:c2:c0:96:05 suppRates statusCode is 0 and gotSuppRatesElement is 1
*apfMsConnTask_4: Jan 28 23:04:59.526: 00:1e:c2:c0:96:05 apfProcessAssocReq (apf_80211.c:7830) Changing state for mobile 00:1e:c2:c0:96:05 on AP 0c:d9:96:ba:7d:20 from Idle to AAA Pending
*apfMsConnTask_4: Jan 28 23:04:59.526: 00:1e:c2:c0:96:05 Scheduling deletion of Mobile Station: (callerId: 20) in 10 seconds
*radiusTransportThread: Jan 28 23:04:59.550: 00:1e:c2:c0:96:05 Username entry (00-1E-C2-C0-96-05) created for mobile, length = 253
*radiusTransportThread: Jan 28 23:04:59.550: 00:1e:c2:c0:96:05 Username entry (00-1E-C2-C0-96-05) created in mscb for mobile, length = 253
*apfReceiveTask: Jan 28 23:04:59.550: 00:1e:c2:c0:96:05 Received SGT for this Client.
*apfReceiveTask: Jan 28 23:04:59.550: 00:1e:c2:c0:96:05 Redirect URL received for client from RADIUS. Client will be moved to WebAuth_Reqd state to facilitate redirection. Skip web-auth Flag = 0
*apfReceiveTask: Jan 28 23:04:59.550: 00:1e:c2:c0:96:05 Resetting web IPv4 acl from 255 to 255
*apfReceiveTask: Jan 28 23:04:59.550: 00:1e:c2:c0:96:05 Resetting web IPv4 Flex acl from 65535 to 65535
*apfReceiveTask: Jan 28 23:04:59.550: 00:1e:c2:c0:96:05 Applying Interface policy on Mobile, role Unassociated. Ms NAC State 2 Quarantine Vlan 0 Access Vlan 84
*apfReceiveTask: Jan 28 23:04:59.550: 00:1e:c2:c0:96:05 Re-applying interface policy for client
*apfReceiveTask: Jan 28 23:04:59.550: 00:1e:c2:c0:96:05 0.0.0.0 START (0) Changing IPv4 ACL 'none' (ACL ID 255) ===> 'none' (ACL ID 255) --- (caller apf_policy.c:2164)
*apfReceiveTask: Jan 28 23:04:59.550: 00:1e:c2:c0:96:05 0.0.0.0 START (0) Changing IPv6 ACL 'none' (ACL ID 255) ===> 'none' (ACL ID 255) --- (caller apf_policy.c:2185)
*apfReceiveTask: Jan 28 23:04:59.550: 00:1e:c2:c0:96:05 apfApplyWlanPolicy: Retaining the ACL recieved in AAA attributes 0 on mobile
*apfReceiveTask: Jan 28 23:04:59.551: 00:1e:c2:c0:96:05 apfApplyWlanPolicy: Apply WLAN Policy over PMIPv6 Client Mobility Type
*apfReceiveTask: Jan 28 23:04:59.551: 00:1e:c2:c0:96:05 Inserting AAA Override struct for mobile
MAC: 00:1e:c2:c0:96:05, source 2
*apfReceiveTask: Jan 28 23:04:59.551: 00:1e:c2:c0:96:05 0.0.0.0 START (0) Initializing policy
*apfReceiveTask: Jan 28 23:04:59.551: 00:1e:c2:c0:96:05 0.0.0.0 START (0) Change state to AUTHCHECK (2) last state START (0)
*apfReceiveTask: Jan 28 23:04:59.551: 00:1e:c2:c0:96:05 0.0.0.0 AUTHCHECK (2) Change state to L2AUTHCOMPLETE (4) last state AUTHCHECK (2)
*apfReceiveTask: Jan 28 23:04:59.551: 00:1e:c2:c0:96:05 Not Using WMM Compliance code qosCap 00
*apfReceiveTask: Jan 28 23:04:59.551: 00:1e:c2:c0:96:05 0.0.0.0 L2AUTHCOMPLETE (4) Plumbed mobile LWAPP rule on AP 0c:d9:96:ba:7d:20 vapId 1 apVapId 1 flex-acl-name:
*apfReceiveTask: Jan 28 23:04:59.551: 00:1e:c2:c0:96:05 0.0.0.0 L2AUTHCOMPLETE (4) Change state to DHCP_REQD (7) last state L2AUTHCOMPLETE (4)
*apfReceiveTask: Jan 28 23:04:59.551: 00:1e:c2:c0:96:05 apfMsAssoStateInc
*apfReceiveTask: Jan 28 23:04:59.551: 00:1e:c2:c0:96:05 apfPemAddUser2 (apf_policy.c:333) Changing state for mobile 00:1e:c2:c0:96:05 on AP 0c:d9:96:ba:7d:20 from AAA Pending to Associated
*apfReceiveTask: Jan 28 23:04:59.551: 00:1e:c2:c0:96:05 apfPemAddUser2:session timeout forstation 00:1e:c2:c0:96:05 - Session Tout 1800, apfMsTimeOut '1800' and sessionTimerRunning flag is 0
*apfReceiveTask: Jan 28 23:04:59.551: 00:1e:c2:c0:96:05 Scheduling deletion of Mobile Station: (callerId: 49) in 1800 seconds
*apfReceiveTask: Jan 28 23:04:59.551: 00:1e:c2:c0:96:05 Func: apfPemAddUser2, Ms Timeout = 1800, Session Timeout = 1800
*apfReceiveTask: Jan 28 23:04:59.551: 00:1e:c2:c0:96:05 Sending Assoc Response to station on BSSID 0c:d9:96:ba:7d:2f (status 0) ApVapId 1 Slot 1
*apfReceiveTask: Jan 28 23:04:59.551: 00:1e:c2:c0:96:05 apfProcessRadiusAssocResp (apf_80211.c:3066) Changing state for mobile 00:1e:c2:c0:96:05 on AP 0c:d9:96:ba:7d:20 from Associated to Associated
*DHCP Socket Task: Jan 28 23:04:59.567: 00:1e:c2:c0:96:05 DHCP received op BOOTREQUEST (1) (len 308,vlan 84, port 13, encap 0xec03)
*DHCP Socket Task: Jan 28 23:04:59.567: 00:1e:c2:c0:96:05 DHCP (encap type 0xec03) mstype 0ff:ff:ff:ff:ff:ff
*DHCP Socket Task: Jan 28 23:04:59.567: 00:1e:c2:c0:96:05 DHCP dropping packet due to ongoing mobility handshake exchange, (siaddr 0.0.0.0, mobility state = 'apfMsMmQueryRequested'
*DHCP Socket Task: Jan 28 23:05:01.523: 00:1e:c2:c0:96:05 DHCP received op BOOTREQUEST (1) (len 308,vlan 84, port 13, encap 0xec03)
*DHCP Socket Task: Jan 28 23:05:01.523: 00:1e:c2:c0:96:05 DHCP (encap type 0xec03) mstype 0ff:ff:ff:ff:ff:ff
*DHCP Socket Task: Jan 28 23:05:01.523: 00:1e:c2:c0:96:05 DHCP dropping packet due to ongoing mobility handshake exchange, (siaddr 0.0.0.0, mobility state = 'apfMsMmQueryRequested'
*mmMaListen: Jan 28 23:05:02.362: 00:1e:c2:c0:96:05 0.0.0.0 DHCP_REQD (7) State Update from Mobility-Incomplete to Mobility-Complete, mobility role=ExpForeign, client state=APF_MS_STATE_ASSOCIATED
*mmMaListen: Jan 28 23:05:02.362: 00:1e:c2:c0:96:05 apfMsRunStateInc
*mmMaListen: Jan 28 23:05:02.362: 00:1e:c2:c0:96:05 0.0.0.0 DHCP_REQD (7) Change state to RUN (20) last state DHCP_REQD (7)
*mmMaListen: Jan 28 23:05:02.362: 00:1e:c2:c0:96:05 0.0.0.0 RUN (20) Reached PLUMBFASTPATH: from line 5793
*mmMaListen: Jan 28 23:05:02.362: 00:1e:c2:c0:96:05 0.0.0.0 RUN (20) Adding Fast Path rule
type = Airespace AP Client
on AP 0c:d9:96:ba:7d:20, slot 1, interface = 13, QOS = 0
IPv4 ACL ID = 255, IPv6 ACL ID = 255,
*mmMaListen: Jan 28 23:05:02.362: 00:1e:c2:c0:96:05 0.0.0.0 RUN (20) Fast Path rule (contd...) 802.1P = 0, DSCP = 0, TokenID = 15206 Local Bridging Vlan = 84, Local Bridging intf id = 0
*mmMaListen: Jan 28 23:05:02.363: 00:1e:c2:c0:96:05 0.0.0.0 RUN (20) Successfully plumbed mobile rule (IPv4 ACL ID 255, IPv6 ACL ID 255, L2 ACL ID 255)
*pemReceiveTask: Jan 28 23:05:02.364: 00:1e:c2:c0:96:05 Set bi-dir guest tunnel for 00:1e:c2:c0:96:05 as in Export Foreign role
*pemReceiveTask: Jan 28 23:05:02.364: 00:1e:c2:c0:96:05 0.0.0.0 Added NPU entry of type 1, dtlFlags 0x4
*pemReceiveTask: Jan 28 23:05:02.364: 00:1e:c2:c0:96:05 Skip Foreign / Export Foreign Client IP 0.0.0.0 plumbing in FP SCB
*DHCP Socket Task: Jan 28 23:05:03.869: 00:1e:c2:c0:96:05 DHCP received op BOOTREQUEST (1) (len 308,vlan 84, port 13, encap 0xec03)
*DHCP Socket Task: Jan 28 23:05:03.869: 00:1e:c2:c0:96:05 DHCP (encap type 0xec03) mstype 0ff:ff:ff:ff:ff:ff
*DHCP Socket Task: Jan 28 23:05:03.869: 00:1e:c2:c0:96:05 DHCP processing DHCP REQUEST (3)
*DHCP Socket Task: Jan 28 23:05:03.869: 00:1e:c2:c0:96:05 DHCP   op: BOOTREQUEST, htype: Ethernet, hlen: 6, hops: 0
*DHCP Socket Task: Jan 28 23:05:03.869: 00:1e:c2:c0:96:05 DHCP   xid: 0xafea6bc9 (2951375817), secs: 5, flags: 0
*DHCP Socket Task: Jan 28 23:05:03.869: 00:1e:c2:c0:96:05 DHCP   chaddr: 00:1e:c2:c0:96:05
*DHCP Socket Task: Jan 28 23:05:03.869: 00:1e:c2:c0:96:05 DHCP   ciaddr: 0.0.0.0, yiaddr: 0.0.0.0
*DHCP Socket Task: Jan 28 23:05:03.869: 00:1e:c2:c0:96:05 DHCP   siaddr: 0.0.0.0, giaddr: 0.0.0.0
*DHCP Socket Task: Jan 28 23:05:03.869: 00:1e:c2:c0:96:05 DHCP   requested ip: 10.130.98.8
*DHCP Socket Task: Jan 28 23:05:03.887: 00:1e:c2:c0:96:05 DHCP received op BOOTREPLY (2) (len 320,vlan 84, port 13, encap 0xec07)
*DHCP Socket Task: Jan 28 23:05:03.887: 00:1e:c2:c0:96:05 DHCP processing DHCP ACK (5)
*DHCP Socket Task: Jan 28 23:05:03.887: 00:1e:c2:c0:96:05 DHCP   op: BOOTREPLY, htype: Ethernet, hlen: 6, hops: 0
*DHCP Socket Task: Jan 28 23:05:03.887: 00:1e:c2:c0:96:05 DHCP   xid: 0xafea6bc9 (2951375817), secs: 0, flags: 0
*DHCP Socket Task: Jan 28 23:05:03.887: 00:1e:c2:c0:96:05 DHCP   chaddr: 00:1e:c2:c0:96:05
*DHCP Socket Task: Jan 28 23:05:03.887: 00:1e:c2:c0:96:05 DHCP   ciaddr: 0.0.0.0, yiaddr: 10.130.98.8
*DHCP Socket Task: Jan 28 23:05:03.887: 00:1e:c2:c0:96:05 DHCP   siaddr: 10.30.4.173, giaddr: 0.0.0.0
*DHCP Socket Task: Jan 28 23:05:03.887: 00:1e:c2:c0:96:05 DHCP   server id: 1.1.1.2 rcvd server id: 1.1.1.2
*DHCP Socket Task: Jan 28 23:05:03.887: 00:1e:c2:c0:96:05 10.130.98.8 RUN (20) DHCP Address Re-established
*DHCP Socket Task: Jan 28 23:05:03.887: 00:1e:c2:c0:96:05 10.130.98.8 RUN (20) Reached PLUMBFASTPATH: from line 6978
*DHCP Socket Task: Jan 28 23:05:03.887: 00:1e:c2:c0:96:05 10.130.98.8 RUN (20) Replacing Fast Path rule
type = Airespace AP Client
on AP 0c:d9:96:ba:7d:20, slot 1, interface = 13, QOS = 0
IPv4 ACL ID = 255, IPv6 ACL ID
*DHCP Socket Task: Jan 28 23:05:03.887: 00:1e:c2:c0:96:05 10.130.98.8 RUN (20) Fast Path rule (contd...) 802.1P = 0, DSCP = 0, TokenID = 15206 Local Bridging Vlan = 84, Local Bridging intf id = 0
*DHCP Socket Task: Jan 28 23:05:03.888: 00:1e:c2:c0:96:05 10.130.98.8 RUN (20) Successfully plumbed mobile rule (IPv4 ACL ID 255, IPv6 ACL ID 255, L2 ACL ID 255)
*DHCP Socket Task: Jan 28 23:05:03.888: 00:1e:c2:c0:96:05 Assigning Address 10.130.98.8 to mobile
*DHCP Socket Task: Jan 28 23:05:03.888: 00:1e:c2:c0:96:05 DHCP success event for client. Clearing dhcp failure count for interface management.
*DHCP Socket Task: Jan 28 23:05:03.888: 00:1e:c2:c0:96:05 DHCP success event for client. Clearing dhcp failure count for interface management.
*DHCP Socket Task: Jan 28 23:05:03.888: 00:1e:c2:c0:96:05 DHCP successfully bridged packet to STA
*pemReceiveTask: Jan 28 23:05:03.889: 00:1e:c2:c0:96:05 Set bi-dir guest tunnel for 00:1e:c2:c0:96:05 as in Export Foreign role
*pemReceiveTask: Jan 28 23:05:03.889: 00:1e:c2:c0:96:05 10.130.98.8 Added NPU entry of type 1, dtlFlags 0x4
*pemReceiveTask: Jan 28 23:05:03.890: 00:1e:c2:c0:96:05 Skip Foreign / Export Foreign Client IP 10.130.98.8 plumbing in FP SCB
*apfReceiveTask: Jan 28 23:05:18.716: 00:1e:c2:c0:96:05 Received SGT for this Client.
*apfReceiveTask: Jan 28 23:05:18.716: 00:1e:c2:c0:96:05 Resetting web IPv4 acl from 0 to 255
*apfReceiveTask: Jan 28 23:05:18.716: 00:1e:c2:c0:96:05 Resetting web IPv4 Flex acl from 65535 to 65535
*apfReceiveTask: Jan 28 23:05:18.716: 00:1e:c2:c0:96:05 AAA redirect is NULL. Skipping Web-auth for Radius NAC enabled WLAN.
*apfReceiveTask: Jan 28 23:05:18.716: 00:1e:c2:c0:96:05 apfApplyWlanPolicy: Retaining the ACL recieved in AAA attributes 255 on mobile
*apfReceiveTask: Jan 28 23:05:18.716: 00:1e:c2:c0:96:05 apfApplyWlanPolicy: Apply WLAN Policy over PMIPv6 Client Mobility Type
*apfReceiveTask: Jan 28 23:05:18.716: 00:1e:c2:c0:96:05 Inserting AAA Override struct for mobile
MAC: 00:1e:c2:c0:96:05, source 2
*apfReceiveTask: Jan 28 23:05:18.717: 00:1e:c2:c0:96:05 Setting session timeout 3600 on mobile 00:1e:c2:c0:96:05
*apfReceiveTask: Jan 28 23:05:18.717: 00:1e:c2:c0:96:05 Session Timeout is 3600 - starting session timer for the mobile
*apfReceiveTask: Jan 28 23:05:18.717: 00:1e:c2:c0:96:05 Applying cached RADIUS Override values for mobile 00:1e:c2:c0:96:05 (caller pem_api.c:2307)
*apfReceiveTask: Jan 28 23:05:18.717: 00:1e:c2:c0:96:05 Setting session timeout 3600 on mobile 00:1e:c2:c0:96:05
*apfReceiveTask: Jan 28 23:05:18.717: 00:1e:c2:c0:96:05 Session Timeout is 3600 - starting session timer for the mobile
*apfReceiveTask: Jan 28 23:05:18.717: 00:1e:c2:c0:96:05 10.130.98.8 RUN (20) Applied RADIUS override policy
*apfReceiveTask: Jan 28 23:05:18.717: 00:1e:c2:c0:96:05 10.130.98.8 RUN (20) Replacing Fast Path rule
type = Airespace AP Client
on AP 0c:d9:96:ba:7d:20, slot 1, interface = 13, QOS = 0
IPv4 ACL ID = 255, IPv6 ACL ID
*apfReceiveTask: Jan 28 23:05:18.717: 00:1e:c2:c0:96:05 10.130.98.8 RUN (20) Fast Path rule (contd...) 802.1P = 0, DSCP = 0, TokenID = 15206 Local Bridging Vlan = 84, Local Bridging intf id = 0
*apfReceiveTask: Jan 28 23:05:18.717: 00:1e:c2:c0:96:05 10.130.98.8 RUN (20) Successfully plumbed mobile rule (IPv4 ACL ID 255, IPv6 ACL ID 255, L2 ACL ID 255)
*apfReceiveTask: Jan 28 23:05:18.717: 00:1e:c2:c0:96:05 Not Using WMM Compliance code qosCap 00
*apfReceiveTask: Jan 28 23:05:18.717: 00:1e:c2:c0:96:05 10.130.98.8 RUN (20) Plumbed mobile LWAPP rule on AP 0c:d9:96:ba:7d:20 vapId 1 apVapId 1 flex-acl-name:
*apfReceiveTask: Jan 28 23:05:18.717: 00:1e:c2:c0:96:05 10.130.98.8 RUN (20) Change state to RUN (20) last state RUN (20)
*apfReceiveTask: Jan 28 23:05:18.717: 00:1e:c2:c0:96:05 apfMsAssoStateInc
*apfReceiveTask: Jan 28 23:05:18.717: 00:1e:c2:c0:96:05 apfPemAddUser2 (apf_policy.c:333) Changing state for mobile 00:1e:c2:c0:96:05 on AP 0c:d9:96:ba:7d:20 from AAA Pending to Associated
*apfReceiveTask: Jan 28 23:05:18.717: 00:1e:c2:c0:96:05 apfPemAddUser2:session timeout forstation 00:1e:c2:c0:96:05 - Session Tout 3600, apfMsTimeOut '1800' and sessionTimerRunning flag is 1
*apfReceiveTask: Jan 28 23:05:18.717: 00:1e:c2:c0:96:05 Scheduling deletion of Mobile Station: (callerId: 49) in 3600 seconds
*apfReceiveTask: Jan 28 23:05:18.717: 00:1e:c2:c0:96:05 Func: apfPemAddUser2, Ms Timeout = 1800, Session Timeout = 3600
*apfReceiveTask: Jan 28 23:05:18.718: 00:1e:c2:c0:96:05 Sending Assoc Response to station on BSSID 0c:d9:96:ba:7d:2f (status 0) ApVapId 1 Slot 1
*apfReceiveTask: Jan 28 23:05:18.718: 00:1e:c2:c0:96:05 apfProcessRadiusAssocResp (apf_80211.c:3066) Changing state for mobile 00:1e:c2:c0:96:05 on AP 0c:d9:96:ba:7d:20 from Associated to Associated
*pemReceiveTask: Jan 28 23:05:18.720: 00:1e:c2:c0:96:05 Set bi-dir guest tunnel for 00:1e:c2:c0:96:05 as in Export Foreign role
*pemReceiveTask: Jan 28 23:05:18.720: 00:1e:c2:c0:96:05 10.130.98.8 Added NPU entry of type 1, dtlFlags 0x4

Guest Cert problems ISE and Anchor WLC

I'm setting up new Guest Wireless, I have 2 internal foreign 5508 WLC's talking to 2 DMZ anchor WLC's. The guest connects to Guest SSID and the anchor controllers acts as a DHCP server, the Guest interface configured on the WLC is the in the range of the DHCP scope I've setup. The DHCP scope is using the anchor WLC Mgmt interface as the DHCP server.
Guest SSID - is setup for Webauth and Guest is redirected to the ISE server https://wlc.company.com/login...., when the page is presented to the Guest they get cert problem because the cert is not trusted (its an Internal Cert), Guest logins in ok and the AUP says "cert not trusted" 1.1.1.1 name of the WLC wlc.company.com.
In the browser Guest has https://wlc.company.com/loginredirecthttps://1.1.1.1........
1.1.1.1 is the Virtual interface of the Anchor WLC.
How can I get the client to stop using the Virtual Interface for cert. Why is the WLC doing this? I gather something to do with DHCP?
My plan is to apply a External Cert on the ISE for Guests, that way they will automatically trust a cert from Geotrust for example. But I'm going to still run into this Cert "not trusted" problem where the Guest is not trusting the WLC anchor Virtual Interface 1.1.1 . Why is the guest using the Virtual interface error 1.1.1.1. I've even added the ISE name of the cert to the Virtual interface, same problem, instead its just says wlc.company.com not trusted. I have also imported the cert onto the WebAuth cert on anchor WLC, still doesn't work.
Hopefully I've explained this ok.....any ideas? but if the Guest page keeps getting presented with
https://wlc.company.com/loginredirecthttps://1.1.1.1........ it will never work.

I followed Richard's advice and started from scratch, removing LWA and implementing CWA -MAB. It didn't take too long to setup CWA and get authentication working, I appled a Preauth ACL on WLC's and on ISE under Authorization pofile (CWA)
This is when the problems started happening, I was using the default ISE Authorization profile
cisco-av-pair = url-redirect=https://ip:8443/guestportal/gateway?sessionid=SessionValueIdValue&action=cwa.which is not what I want, again the certificate is the server cert which is not an external Cert that the guest wants to see. The user can login fine, unlike LWA, with Firefox or IE it would accept the cert and login so at least I had a working Guest wifi solution. Though there was a cert error symbol at the end of the browser url.
The next step I tried was to change the Authorization Profile to
(wireless.company.com which is a C-NAME for ISE box and has this Alias in the cert, this was a test before I apply the external cert)
cisco-av-pair = url-redirect=https://wireless.company.com:8443/guestportal/gateway?sessionid=SessionValueIdValue&action=cwa
I applied the change and the new page appeared on the users laptop, great, but this time users were declined access via live Authentications, reason "Cannot login due to session id expiry, please login a again", I created a new user a/c, same problem. Not good. Ok so I thought well if I want clear all these stale session id's that appartenly exist I'll stop/start the application which I did from the command line, still the same error "Cannot login due to session id expiry". hmmm, whats going on here.
I then rebooted the ISE (this must clear all the sessions!), reboot I performed from home and now for some reason I cannot login to the ISE front end GUI with the admin account or my account. Tried resetting the GUI password for admin and other admin users, the message "Error: cannot reset password this can only be performed on Standalone or Primary node" Well what have I done, just rebooted ISE nothing else apart from changing authorization profile. This box is a Standalone node. Without seeing if the clients connect due t no GUI access, I have referred this issue to TAC!
Also I don't like the fact that your have to install a external cert against the internal node name, epsecially when its external. But again I haven't reached this part yet.

Guest Anchor with web auth using ISE guest portal

Hello All,
Before launching into my exact issues, could anyone confirm if they have completed a wireless Guest anchor setup using 2504 controllers on 7.4 as the anchor (5508 is the foreign) with webauth external redirection at ISE 1.1.3 using ISE Guest Services?
I am attempting this for an internal POC and have hit a couple of issues. Firstly I am looking for correct configuration confirmation prior to going in depth with a couple of the issues. I've been using the TrustSec 2.1 how to guides to build the parts I am not strong on so if anyone has actual completed this setup, I'd love to go through it with you.
massive thanks to anyone that can assist.
JS.

Thanks for the reply RikJonAtk.
so to start with, based on the trust sec documents, of the guest WLAN on the anchor I need to configure mac filtering at the layer 2 security menu as well as enable RADIUS NAC under the Advanced tab. But when I do this, I get an error message that states that mac filitering and RADIUS NAC cannot be enable at the same time.
Additionally, if I just enable the RADIUS NAC setting under the Advanced tab in the WLAN, I get another error message that states that the priority order for Web-Auth can only be set for radius, so I go to the AAA server tab and send local and LDAP to the not use column and hit apply. If I move to another menu then check the priority order again under the AAA servers tab, the local and LDAP have been moved back to the menu field to be used again. So I initially though it might be a bug, but I was hoping to find someone here that has done this already and can look at my issues and maybe walk me through their configs, which I'll mirror and see how it goes.
Thanks in Advanced,
JS

ISE and wireless CWA

Need some help on this one.
This is ISE 1.1.1 and WLC 7.2
I want to use CWA and Webauth for guest users, and I have configured that on the ISE and WLC.
This is working but I need some clarification :-)
First I tried to use AuthC policy with
allowed protocolls= PAP-ASCII + Host lookup
Result of that was that for Mac OS X an MS PC it's no problem, I get redirected, logon, press yes on the AUP and I can go on surfing the web.
But on the iOS devices I get redirected to the guest logon page, put in my credentials and insted of the AUP page I get a network error, could not connect.
If I change AuthC to
allowed protocolls= Default Network Access
All is working fine for all endpoints.
Im looking at the RADIUS Authentication Details but I dont understand what iPhone/iPad do diffrent?
An other question here, can I get a redirect after successfull logon instead of 'Please retry your orginal URL request'?
Thanks!

I did solv this (sort of) using html redirect on a custom portal, going to the customers web page.
http://www.cisco.com/">
It would be nice to have a redirect to the page the user wanted to view prior to login but this is good enough

CWA using ISE and mobility anchor

Similar Messages

Maybe you are looking for