Daily Change Number.

Is anybody using this functionality in your SAP system ? This is different than regular change number.

Dear Vinay,
I will explain very clearly,
1.If there are changes in material master which will become effective immediately,then ECN without release key will be created and the
changes will be made with respect to that Change number.
2.If the Changes are for a BOM ,then ECN will be created with Release key and the changes will be made.
3.Once if the changes are to be made effective,then in CC02,by entering the Change number the same will be released and the
changes made with respect to that ECN will become effective.
4.IF the BOM changes are to be made effective immediately,then ECN without release key itself can be used and the changes can be
made or create with release key ,but after making BOM Changes,the same has to be released.
5.Daily an ECN will not created,if needed then it will be created on that particular day.
6.Revert back if more clarifications are needed.
Regards
Mangalraj.S

Similar Messages

Daily sequence number

Hi,
I need a clean solution for a daily sequence number (starts from 1 everyday). Clean in the sense that upon initial setup, I do not have to do anything and I can get my number everyday by just one jdbc call/query.
Thank you in advance.

What is the business justification for this requirement? Normally, you should just use a regular non-resetting sequence. If users want to see a "pretty" sequence number, simply generate something for them when you query the data using the row_number, rank, or dense_rank analytic functions. If users want to see sequences reset, they probably also want to see gap-free sequences, which is not something that you can ever guarantee in a scalable system where multiple users are allowed, though you can present gap-free sequences of values at query time.
You can have a job that either drops and recreates the sequence every day or that goes through some logic to reset the sequence to 1 by changing the increment. This gets rather hairy, though, because the job will fail (or fail to run) on occasion and requires that no one be processing data at the time.
Justin
Distributed Database Consulting, Inc.
http://www.ddbcinc.com/askDDBC

How to find Change number for a Material

Hi,
If we know the material number and Revision level then how can we find the Change Number of that material.
Is there any table in which i can find Change number for a revision level or is there any Function module available.
Regards,
Vaibhav

Hi Vaibhav,
Is there any table to find the change number and revision level of a material. I have change number and material and revision level coming from external system. But i need to check that with SAP whether it exists or not.
Is there any table link to find whether a material has change number.

Error while changing BOM with change number

Hi ALL, Please help me with followed error message, I am using ECM. I created ECR and converted to ECO and then released.
Object management record cannot be generated
Message no. 29046
Diagnosis
You want to change the BOM with the entered change number.
One of the following situations triggered this error message:
1. The indicator that allows automatic generation is not set for object type BOM in the change master.
2. The indicator generation only on initial creation is set for object type BOM
3. You are processing a change request.
System response
The system checks whether the indicator object management record will be generated is set in the change master.
If the indicator generation only on initial creation is set, the system checks whether the BOM exists in the system.
Procedure
If you are authorized to change the change master, execute the following steps:
For 1.)
Set this indicator for object type BOM or create the control record in the change master.
For 2.)
If the BOM already exists in the system and the generation only on initial creation indicator is set, the system can no longer generate the control record automatically.
In this case you have to add the object control record to the change master first, then you can change the BOM in relation to the change number.
For 3.)
You cannot generate any object control records for a change request.

Hi
With your question regarding changing BOM with change number it looks lke there may be problem in defining the Object types,objects.Moreover whenever converted to ECO you need to enter into cs02 tcode for changing the bom with relevant change number and valid from date.
Hope this gives you a clear idea.let me know if you need anyfurther inputs.
Regards
Praveen

Change number in material master required steps to use

Hi All.
Thanks in advance sap mm dudes.
Need steps in sap mm material master change number.
creation of change number and usage of change number
Display of list of changes.
Regards.
parameshwar

Dear Parameshwar,
1.I assume you have created a change number without release key in CC01.
2.In CC02,for the same change number goto object types and include the check box against material for the first 3 check box and
save the change number.
3.Now check in MM02 for any material master changes or I would suggest you to create a new change number with valid from
date as current date,include the settings for material under object types and then check in MM02.
Check and revert.
Regards
Mangalraj.S

Need to fetch change number for tcode IA06

Can anyone please tell me how do I fetch the change number (Aennr) in case of tasklist chage? Tcode IA06?
I am using FM CP_EX_PLAN_READ which returs me change number..but it is not populated....
Plz help.

hi check this..
check the table AENR for the aennr values...
here is an example for this fm..
call function 'CP_EX_PLAN_READ'
     exporting
          plnty_imp        = i_plnty
          plnnr_imp        = i_plnnr
          plnal_imp        = i_plnal
          sttag_imp        = i_sttag
          cuobj_imp        = i_cuobj
          parnt_imp        = i_parnt
          i_plant          = i_werks
          tca11_imp        = ls_tca11
     tables
          plmz_exp         = lt_plmz
          plpo_exp         = lt_plpo
     exceptions
          not_found        = 1
          plnal_initial    = 2
          others           = 3.
regards,
venkat

How to fetch the latest change number from CDPOS Table..?

Hi All,
im trying to fetch teh change number from CDPOS with the below select, but my requirement is always i wants to fetch the latest change number.
          SELECT SINGLE objectid changenr FROM cdpos
                 INTO wa_cdpos
                 WHERE objectid = wa_e1kna1m-kunnr
                 AND ( tabname = 'KNA1' OR tabname = 'KNVV')
                 AND   fname = 'AUFSD'
                 AND ( value_new = '01' OR value_new = space ).
Please let me know how to achive this..?
Ashok

try this way
"           SELECT SINGLE objectid changenr FROM cdpos
"                 INTO wa_cdpos
           SELECT objectid changenr FROM cdpos
                  INTO table t_cdpos
                  WHERE objectid = wa_e1kna1m-kunnr
                  AND ( tabname = 'KNA1' OR tabname = 'KNVV')
                  AND   fname = 'AUFSD'
                  AND ( value_new = '01' OR value_new = space ).
SORT t_cdpos by changenr Descending.
read t_cdos index 1.    "this is the latest change
Prabhudas

Can't make a selection of my pathes even if i have set a program change number for each one.Why is that happening?

Hi everybody!
I send program change messages from my midi controller and the messages are accepted by mainstage 3 as shown in the midi message window,but i can't make a selection of my pathes even if i have set a program change number for each patch.Why is that happening?
I use a novation SL mki or a KORG Triton Le or a m-audio axiom 49 as midi controllers.The program change messages are transmitted by all the devices i mentioned above and shown as received in the midi messages window of mainstage 3.
Has anyone the same experience?

Hi
Have you selected the correct device as the Program Change device and MIDI channel in the Concert Inspector?
CCT

In iPhoto how do I open Photo Grid to change number of caption lines?

In iPhoto how do I open Photo Grid to change number of caption lines?

In iPhoto '11 you can only display two lines below the thumbnails of your photos when you browse an event or an album, the titles and the ratings. The title will be truncated, if it does not fit into the single line. From the iPhoto help:
To show title and rating information below photos:
Click to select Photos in the Source list.
Choose View, and then choose the information you want to view:
Titles
Rating
The information field you chose appears below your photos.
To hide this information, choose View, and then choose the information you want to hide.
Regards
Léonie

PI 7.31 (single stack) posting RFC gives this error: RFC_ERROR_SYSTEM_FAILURE: Processing of change number CO-01234 cancelled (raised by system ECCHostXYZ)

I'm trying to determine if I am dealing with an RFC connection issue or just an error resulting from the RFC itself.
The error says "Processing of change number...cancelled (raised by...ECCHostXYZ)".
I thought this was a problem with my RFC config because it is labeled as "RFC_ERROR_SYSTEM_FAILURE".
However, when I google that specific message, it appears to be an error specific to change order creation.
Here’s my google search: http://goo.gl/ZhKsm3
Here is the error again:
RFC_ERROR_SYSTEM_FAILURE: Processing of change number CO-01234 cancelled (raised by system ED1|ecc-host-xyz)
When I check ST22, I see no RFC errors.

Hi Jody,
No st22 exception is needed to be throwed in order to raise a controlled exception in the RFC.
You would need to check the RFC in the ECC system with the data that you are sending from PI, if the data is the same, you would need to check PI user RFC roles with the ECC roles user that you used to check the data integrity in the ECC test.
To avoid this error you can do a Z RFC to wrap the standard RFC and to control the exceptions errors with a BAPIRET2 strucutre to return to PI.
Hope this helps.
Regards.

Change the validity date in change number

hi team,
I want to change the validity date of a change number from 01.01.09 to 01.03.09. I am getting an error "A BOM has already been changed using a change number with the same valid-from date as the selected date 03.01.2009". I can change the date to before 01.01.09 but cannot after 01.01.09.
Can you please help me.
thank you,
Satish

Dear Mamiditi Satish Kumar,
Is it a change number with release key or without release key?
Do you want to assign a different validity date for the changes made using that change number?
Try using alternative date field in CC02.and you have to select the object to assign the alternative date.
Say if you want to assign an alternative date for a processed BOM,you have to select that object and
enter the alternative date.
Regards
Mangalraj.S

MM02 - Enable options change number, change overview and change documents

I am with the following problem: I enter the transaction MM02, I enter the material 1000765, I select the view "Classification". Later I access the environment option from the menu bar and options for change number, change overwiew and change documents are disabled.
How do I enable these options change number, change overview and change documents?
Regards,
Sérgio Salomã

Hi Sergio,
If we activate the change documents for classification data, then we will be able to see the CHANGE DOCUMENTS for characteristic values through CL20N transaction (CL20N via menu ENVIRONMENT --> Change Documents) or MM02.
For reference please check SAP Note 65124.
For enabling change documents for classification data in SPRO --> Cross-Application Components --> Classification System --> Classes --> Maintain Object Types and Class Types.
In this enter into MARA table entry. Inside that corresponding to the respective CLASS TYPE (say 001) enable the CHANGE DOCS check box in Classifications part (For enabling this please check SAP Note 65124). Then for this CLASS TYPE (say 001) inside the OBJECTS folder, enable the CHANGE DOCS CLASS checkbox also.
Now in MM02 and in CL20N under menu Environment --> Change Documents you can view all the changes done to that characteristic values.
Once the change documents is activated, then we can get the change documents details in CDHDR and CDPOS tables. The OBJECTCLAS may be "CLASSIFY". We can also use the "CLLA_CHANGE_DOC_CLASSIFICATION" function module to fetch the data from these tables.
Hope this helps in solving your issue.
Thanks and Regards,
Harish kumar.

Change Number Release (JS41)

Hi All,
I am trying to release a change number from js40, but within
500 secs it gives me the following Dump message saying..
"ABAP/4 processor: TSV_TNEW_PAGE_ALLOC_FAILED"
please suggest any soution to it.
thanks,
Abhay Mehta.

Dear Abhay ,
I have Observed your system closely and found that the table "JGTSADR " contains too many entries (Approx 23 Lacs).
And the program tries to fetch all these entries in the internal table which overflows the internal table memory.
The query which is fetching these records does not contain any filters. Please try to Apply some filters on the select query in consultation with SAP (OSS ) so that you will not face such problems in future.
Reward if Helpful.
Regards,
Nikhil

ECM-Problem with Change number in CS01 and CS02 Transactions

Hi Experts,
I am creating or changing BOM's using above transactions. I am entering the change number while creation and changing the BOM to track the changes.Here my problem is these transactions are not validating the ECM number.
If you enter any value in the change number filed system is allowing me to create a BOM.
I am assuming that becasue of patches applied to system,I am getting this.
kindly help me out on this issue.
Thanks in Advance,
Regards,
Rakesh J
Edited by: J.Rakesh on Apr 22, 2009 10:26 PM

Dear Mangalraj,
Thanks for your reply.
We are not using CC01 transaction to create Change number. Z transaction is there to create change number.
My change number contain alpha numreic charectors Eg : 341793ABCXYZ
Yes, in CS01 system is accepeting any value that we enter :Eg: asddfgh. The value is not there in AENR table.
I observed one thing If I am going to chnage a material using MM02, there its not accepeting any value,its accepeting the values which are there in AENR table otherwise its giving error :Change Number XXXXXXXX does not exist.
My question is same thing should function in CS01 and CS02, why its not happening for these transactions.
Regards,
Rakesh J

Function Module for link Change number to classification

Hello Expert.
what is the Function Module name which will link Classificaiton (tcode:cl03) to change number (cc01) .
regards
srinivas

Hi,
Check business object BUS1003

Daily Change Number.

Similar Messages

Maybe you are looking for