Data Load Error after Client copy on Source System

We did a client copy to our QAS source system.  After that was complete, I tried to do a couple of full data loads.  But they fail.  The only errors I see are on the source system when I try to manual update the Idocs.  They are:
EDI: Partner Profile not available
Entry in inbound table not found
Is there a step I need to take after the client copy and before the loads?  I have a feeling that I'm forgeting something.
Thanks,
Chris

Hi Chris,
Check the following.
1> Go to WE20 check whether you are able to see two logical system in "Partner Type LS" one for Source and one for Myself.
2> If you say Yes for <1> then check in both the logical system, in the classification tab, partner status should be 'active'.
3> Check you have used REMOTE USER in main and in Outbound and inbound Parameters "Post Processing Permitted tab " for each Message type.
4> go to out bound message type and check the "Receiver port" pointing to correct RFC destination for both ( Source and Myself logical system).
If your answer is no for <1> then perform all the steps.
Hope this will help you.
Suneel

Similar Messages

  • Data load delay after DB upgrade in source system

    we have upgraded our source system DB to oracle 11g over the weekend. The first loads of our process chain the master data is taking huge time with the message as
    I am getting message as
    Data Package 000001: sent,not arrived
    Info IDoc 2 : sent , not arrived ; Data passed to port OK
    Info IDoc 1 : sent , not arrived ; Data passed to port OK
    Info IDoc 3 : sent , not arrived ; Data passed to port OK
    Info IDoc 4 : sent , not arrived ; Data passed to port OK
    Request IDoc : Application document posted
    processing (data packet) : No data
    can anyone share ideas on this
    thanks and regards
    Edited by: AAL123 on Sep 26, 2011 7:17 AM

    Hi,
    Check the below given SAP Notes,
    Note: 580869 ( RFC calls can be processed with report RSARFCEX) & 530997.
    Regards,
    Durgesh.

  • AFAB: Runtime Error after client copy.

    Hi all,
    I'm having a problem with the transaction code AFAB (post client copy). After client copy from PRD to DEV, I'm encountering this runtime error "SAPSQL_ARRAY_INSERT_DUPREC -   The ABAP/4 Open SQL array insert results in duplicate database records." whenever I tried to perform AFAB. Test run was executed successfully but I cannot complete the actual background processing.
    I have try with other asset (in the same client) and encounter the same problem. Likewise, I have successfully completed the depre. if I try the same and other asset (in a different client on the same server).
    I've check the number range in FBN1 and have verified that the range is correct.
    Any advice as to how I can solve this problem?
    Thank you.
    Regards.
    p/s: if there is duplication, how do I find where the duplication is located and how do I remove this duplication?
    p/s 2: the standard SQL that is having this problem is "INSERT COBK  FROM TABLE COBK_INS."
    Edited by: Sek Yao Ooi on Aug 5, 2010 5:21 AM

    Solution obtain from snote-83731 ; thanks to SAP-Marketplace's support.
    Issue solved.

  • Error After client copy

    Hi all,
    I did a client copy in ECC IDES  with client 800 as source client.As per the logs , copy is successful.The profile usedf is SAP_ALL.After the copy we logged into the new client which was
    created and it looked good. Checked the Logs in SCC3 and it said that client copy was finished sucessfully.However now when we go and execute transactions  MM01 and VA01, it is  giving a error  saying 
    Batch definition level not found.System inconsistency!
    Not sure what went wrong,  Any suggestions would be Helpful.
    Regards,
    Chaitanya.

    hi...
        send the full details of ur client copy....
       what is ur target client where u did this client copy .. i mean in prod dev

  • Error during data load due to special characters in source data

    Hi Experts,
    We are trying to load Billing data into the BW using the billing item datasource. It seems that there are some special characters in the source data. When the record with these characters is encountered, the request turns red and the package is not loaded even into the PSA. The error we get in the monitor is something like
    'RECORD 5028: Contents from field ****  cannot be converted into type CURR',
    where the field **** is a key figure of type currency. We managed to identify the said record in RSA3 on the source system and found that one of the fields contains some invalid (special) characters that show up as squares in RSA3. The data in the rest of the fields, including the fields mentioned in the error  looks correct.
    Our source system is a non-unicode system wheras the BW system is unicode enabled. I figure that the data in the rest of the fields are getting misaligned due to the presence of the invalid characters in the above field. This was confirmed when we unassigned the field with the special characters from the transfer rules and removed the source field from the transfer structure. After doing this the data was loaded successfully and the request turned green.
    Can anyone suggest a way to either filter out such invalid characters from the source data or make some settings in the BW systems such that the special characters are no longer invalid in the BW system? We cannot write code in the transfer rules because the data package does not even come into the PSA. Is there any other method to solve this problem?
    Regards,
    Ted

    Hi Thad,
    I was wondering, if system is unicode or non unicode that should not matter the amount and currency field . As currencies are defined by SAP and it is in pure English at least a currency code part of 3 Chars. 
    Could this because of some incosistency of data ??
    I would like to know for Which currency  had some special characters it it in that particular record ??
    Hope that helps.
    Regards
    Mr Kapadia

  • BI-RFC problems after client copy

    Hi all
    Client copy was done and after that when I tried to load data in BW, it ran for long time and finally showed cancelled in SM37. When I checked the source system in RSA1, it gave two messages.
    1.Incorrect IDoc type ZSAC008 in the ALE definition of the source system RSAR373
    2.Result of the destination check: Password logon no longer possible - too many failed attempts RSAR375.
    In long text of message 1 suggestion was to enter IDoc type ZSAB003. In SM30 for Message Type RSSEND Basic Type ZSAB003 Release field is empty. Is this error because of this?  After client copy is there a way to restore the settings back to how it was set initially in the development server? Basis told ALEREMOTE & BIWREMOTE are not blocked. What is missing here? Thanks a lot in advance. 
    Subin

    There are a few things need to be performed on basis side after copy .
    1. Restore of Logical system.--> check with Baisis team wheather they have performed this action or not after copy.
    2. Check your source system connection, in rs1-- source sytem --check
    3. Change the aleremote or Bwremote passwords.
    4. Try to logon to your sourcesystem ( from SM59 Tcode) Remote logon.
    Hope this helps.
    Regards,
    Reddy
    Edited by: Reddybl on Apr 1, 2010 11:56 AM

  • Error 8 when starting the extracting the program-data load error:status 51

    Dear all,
    <b>I am facing a data exracton problem while extracting data from SAP source system (Development Client 220). </b>The scenario and related setting are as the flowings:
    A. Setting:
    We have created 2 source system one for the development and another for the quality in BW development client
    1. BW server: SAP NetWeaver 2004s BI 7
    PI_BASIS: 2005_1_700 Level: 12
    SAP_BW: 700 Level:13
    Source system (Development Client 220)
    2. SAP ERP: SAP ERP Central Component 6.0
    PI_BASIS: 2005_1_700 Level: 12
    OS: SunOS
    Source system (Quality Client 300)
    2. SAP ERP: SAP ERP Central Component 6.0
    PI_BASIS: 2005_1_700 Level: 12
    OS: HP-UX
    B. The scenario:
    I was abele to load the Info provider from the Source system (Development Client 220), late we create another Source system (Quality Client 300) and abele to load the Info provider from that,
    After creating the another Source system (Quality Client 300), initially I abele to load the info provider from both the Source system – , but now I am unable to load the Info provider from the (Development Client 220),
    Source system Creation:
    For both 220 and 300, back ground user in source system is same with system type with same authorization (sap_all, sap_new, S_BI-WX_RFC) And user for source system to bw connection is dialog type (S_BI-WX_RFC, S_BI-WHM_RFC, SAP_ALL, SAP_NEW)
    1: Now while at the Info Package : Start data load immediately and then get the
    e-mail sent by user RFCUSER, and the content:
    Error message from the source system
    Diagnosis
    An error occurred in the source system.
    System Response
    Caller 09 contains an error message.
    Further analysis:
    The error occurred in Service API .
    2:Error in the detail tab of the call monitor as under,
    <b>bi data upload error:status 51 - error: Error 8 when starting the extracting the program </b>
    Extraction (messages): Errors occurred
      Error occurred in the data selection
    Transfer (IDocs and TRFC): Errors occurred
    Request IDoc : Application document not posted (red)
      bw side: status 03: "IDoc: 0000000000007088 Status: Data passed to port OK,
                                    IDoc sent to SAP system or external program"
      r<b>/3 side: status 51:  IDoc: 0000000000012140 Status: Application document not posted
                                   Error 8 when starting the extraction program</b>
    Info IDoc 1 : Application document posted (green)
       r/3 side: "IDoc: 0000000000012141 Status: Data passed to port OK
                     IDoc sent to SAP system or external program"
       bw side: "IDoc: 0000000000007089 Status: Application document posted,
                     IDoc was successfully transferred to the monitor updating"
    Have attached screen shots showing error at BW side.
    •     check connection is ok, tried to restore the setting for bw-r3 connection – though same problem
    •     Have checked partner profile.
    <b>what's wrong with the process? </b>
    Best regards,
    dushyant.

    Hi,
       Refer note 140147.
    Regards,
    Meiy

  • SAP* not authorized after Client copy

    Dear All,
    Here's the scenario:
    1. Created a new logical system for a new Quality client 230.
    2. Created the new client 220
    3. scheduled a test remote client copy from the new client, source Production. (Successful)
    4. Scheduled the actual client copy to run last night.
    5. Today morning, I'm logging into the new client with SAP*, it prompted me to change password.
    6. I want to look for the client copy logs (SCC3), but getting "not authorized"
    7. Checked all other transactions, all giving "not authorized" error
    Any help would be appreciated. Thanks in advance.

    Dear Reza,
    Better to go for Client Export Import process . This is what SAP reccomends for coping clients  between
    different systems ( Like from Production to Quality ) as the remote client copy has many
    disadvantages..
    For this 1 ) you should get the downtime of production system and do the client export process .
    SCC8 . See the logs at scc3 .
    2) Copy the datafile and cofile to the Source system
    3) Import it usting stms_import .
    Monitor the logs as the logs will be grown massive and make sure enough space is there.
    4) After client copy , go for post processing ( scc7 ) .
    Hope you are clear and feel free to get back if any doubts.
    Regards,
    Nibu

  • Error in client copy - EFG_FORM_CC_EXIT_AFTER

    Hi,
    I am getting the following error while doing client copy,
    it has copied all the tables , but at the end it gives message,
    ===============================================
    Target Client           500
    Source Client           000
    Copy Type               Local Copy
    Profile                 SAP_CUST
    Status                  Successfully Completed
    User                    SAP*
    Start on                26.09.2007 / 01:48:17
    Last Entry on           26.09.2007 / 02:56:00
    Statistics for this Run
    - No. of Tables             53644 of     53644
    - Deleted Lines                 2
    - Copied Lines            5090006
    arnings and Errors
    Table Name              Component  Package
    EFG_FORM_CC_EXIT_AFTER  CA-GTF-PWB Program Exit has Syntax Errors
    EFG_FORM_CC_EXIT_BEFORE CA-GTF-PWB Program Exit has Syntax Errors
    ============================================================
    please advice.
    regards,
    SM

    Hi Shark,
    Your client copy seems to be ended with just warnings. As mentioned, please correct those 2 forms in the source system and try to import to target client. Discuss with apps member whether they need these 2 mentioned forms. If they don`t need it ,you can ignore the warnings.
    Perform post processing after client copy.
    regards,
    Vinodh.

  • After Client copy - No Authroization Issue

    Dear All,
    Good Day,
    We copied Production data to Quality system through Transport management System. We checked those data copied successfully. After client copy, login in Quality also done successfully
    But unable to run any transaction. no authroization error occur for all the transaction for all the user id.
    "You are not authorized to use transaction XXXX"
    Kindly advice me to resolved this issue.
    Best Regards,
    KSK

    Was security transported down? Can you log into the system as SAP*? If so, check to make sure that all the roles and user masters where copied. You can also run st01 to do an authorization check.

  • Error Loading Hierarchy Error when updating Idocs in Source System

    Hello  Friends,
         I am loading  hierarchy data  using Info pac into  0FUNDS_CTR . I have selected  a hierarchy under hierarchy selections tab  in the Info pac .
    All Partner profiles in WE20 seems OK .   But When I loaded data , throwing errrr message  as below
    Error when updating Idocs in Source System
    Diagnosis
    Errors have been reported in Source System during IDoc update:
    System Response
    Some IDocs have error status.
    Procedure
    Check the IDocs in Source System . You do this using the extraction monitor.
    Error handling:
    How you resolve the errors depends on the error message you get.
    When I checked in TC WE05 says that  IDoc: 0000000000355113 Status: Error during syntax check of IDoc (outbound) with status 26 .
    Please advice .
    Many thanks

    Hi  Krishna4bi,
    Actually we will monitor idoc status in BD87 in SAP BI As well ECC , while extracting the data from source sytem  if any idoc struck we will manually process in BD87 , But you are telling that while loading the datasource the error occurred , so please check once in ECC side . Otherwise see how many packets are still process, make it red that infopackage and do manually update.
    Hope it helps,
    By,
    Praveen Yagnamurthy,
    SAP BI Consultant,
    Blue Marlin Systems-INDIA.
    http://bluemarlinsys.com/bi.

  • Most common BW data load errors in production and how to solve them ..

    Hi All,
    Most common BW data load errors in production and how to solve them ..
    Any doc on it ,if so plz send it across to this id [email protected]
    Thanks in advance.
    Rgrds
    shoba

    hi
    1) RFC connection lost.
    2) Invalid characters while loading.
    3) ALEREMOTE user is locked.
    4) Lower case letters not allowed.
    5) While loading the data i am getting messeage that 'Record
    the field mentioned in the errror message is not mapped to any infoboject in the transfer rule.
    6) object locked.
    7) "Non-updated Idocs found in Source System".
    8) While loading master data, one of the datapackage has a red light error message:
    Master data/text of characteristic 'so and so' already deleted .
    9) extraction job aborted in r3
    10) request couldnt be activated because theres another request in the psa with a smaller sid
    11) repeat of last delta not possible
    12) datasource not replicated
    13) datasource/transfer structure not active ´
    14) Idoc Or Trfc Error
    15. ODS Activation Error

  • TCURM in target client empty after Client Copy

    Hi Experts,
    Has anyone encountered situation whereby TCURM does not contain a record for the target client after Client Copy process is completed? Is this a feature or bug?
    Regards

    Hi ,  I  user the exclude tables option to exclude some tables.
    but I have another problem:  the client copy still failed.  I get these  informations:
    table/object   component                         error
    ANLU           FI-AA-AA                   Field missing locally
    C905            SD-MD-CM                Different Field Names
    IMPTT          PM-EQM-SF-MPC      Field missing locally
    how can i finish my client copy ?   can you give me the solution
    thanks very much

  • Unable to find product categories after client copy

    Hi all,
    We have copied  clients from an existing ones for both SRM and ECC. After client copy we have followed standard procedure after client copy i.e.
    Run transcation BDLS
    created new RFC connections
    changed attributes using the Attributes replace report
    created new distributon model
    maintained CRM parameters
    maintained new site attributes in SMOEAC transaction
    maintained entries in table TWPURLSVR
    however , when i try to create a shopping cart,  I cannot see any product category. The extended attributes for product category point to new ECC client becuse we have run the attributes replace report.
    however in the product category table , COMM_CATEGORY , the product categories listed are all for the old ECC client
    When i tried to load the Object DNL_CUST_PROD1 using transaction R3AS in SRM and tried to pull from new ECC client , it is in runing status for a long time and new categories with new ECC backend reference are not being replicated in the SRM.
    Can you tell me why this could be happening ? How can i get the product categories from new ECC backend into my client?
    Regards,
    Mangesh

    problem solved
    i was using wrong parameters in BDLS

  • Background jobs pointing to old client after client copy

    Hello
    We have recently completed system refresh from PROD system to TEST system.
    We have created new client in new TEST system. Background jobs are copied properly from old client to new client.
    But all these jobs are pointing to old client only. We have deleted old client.
    Hence all these jobs get cancelled.
    How shall I change the client of all the jobs from old to new one.
    -Nandu More

    Please check the thread:
    Error in Background Jobs After Client Copy
    Check some of the TBT* tables.

Maybe you are looking for