Default display settings

Does anyone know what the factory default settings should be on an iMac (2009)?  I know how to change the settings. Rather, I want to get the settings back to exactly what they were.  How can I accomplish that?  Thanks!!

This is the Mac Mini discussion. Post your question in the iMac forum and the folks there will give you a correct answer.
iMac Discussion

Similar Messages

  • Will migration assistant change the default display settings on my new Mac?

    I just set up a new iMac and used Migration Assistant to load from my Time Machine. But now the display looks muted and not as bright. Would Migration Assistant change the default display settings on my new Mac?

    Migration Assistant may not be the cause. But you should reset the NVRAM and see it that fixes the issue.
    Shut down your Mac.
    Locate the following keys on the keyboard: Command (⌘), Option, P, and R. You will need to hold these keys down simultaneously in step 4.
    Turn on the computer.
    Press and hold the Command-Option-P-R keys before the gray screen appears.
    Hold the keys down until the computer restarts and you hear the startup sound for the third time.
    Release the keys.

  • Default Display Settings T61

    Hi
    Does anyone know what the default display settings are for the T61. Some settings were "changed" when the device would not connect to a projector in a hotel. It will now not connect to any external monitor.
    Thanks
    Phil

    Native resolution on 13" MBP is 1280 x 800.
    Open System Preferences > Display
    There you will find a drop down list with different resolutions. Select 1280 x 800

  • Changing default Display Settings

    How can I change my default settings on the Display Performance? I want to change my default settings so that it always shows "High Quality Display."

    You can change them for all new files by going to the Dispaly Performance section of the application prefs. Exixting docs can be changed from the View menu.

  • What are the default display settings on MBP?

    I have been working on finding the best setting for a new video projector in conjunction with my MacBook Pro.
    So I found one - but then when I went back, restarting, the MBP, I thought I was going blind! I have tried a few settings in display, but at the moment they all look "off."
    I want to go back to default -- can someone please tell me what that is?
    Thanks!
    Patty

    The brightness is fine - what I am wondering about is
    the resolution.
    Is default 1440, 900 and Millions?
    That seems to be about right now - feels better to
    the eye!
    Patty
    Hi Patty,
    Yes, that is the correct resolution. 1440X900 is default.

  • Change default query display settings (show more cells)

    Hello Friends!
    I have a little issue with default display settings in the Bex Query Designer.
    Can I change the display settings like in an analyses item e.g. more Number of Data Columns Displayed at once?
    Thank you for your help
    Best regards
    Florian

    You can also look at the following thread -
    show more than 5 column in web analyzer

  • User Display Settings Question

    Howdy!
    Display Colors are all out of whack (Almost looks like a photo negative) but only when logged on as a certain user. Is there a way to restore a users default display settings without changing other user settings?
    Also sRGB and RGB Color sync profiles are missing for this user, the only profile choice is Color LCD.
    Thanks in Advance!

    Howdy John,
    (Nope, a yankee from New Hampsha')
    Thanks for the suggestion, I will give it a try and report back with the results.
    The ColorSync profiles are missing from the colorsync manager > profiles tab when logged on as one user. They aren't missing under my login.
    My three year old daughter got a hold the iBook while my wife was on the phone. Oh well, lesson learned.
    Thanks for your help!
    Gary

  • Use GPO to set default language options, IME, display settings?

    new to GPO, we have a small Windows Server 2012 domain, all clients on Win7 or Win8.  All the clients require the following changes, anything I can automate this with GPO?  thanks
    Under Control Panel\Clock, Language, and Region\Language > Add Traditional Chinese HK SAR
    Under Control Panel\Clock, Language, and Region\Language > Traditional Chinese HK SAR > Options, Add Microsoft Quick IME
    Under Control Panel\Clock, Language, and Region\Language\Advanced settings - change language bar hot keys
        - CTRL+SHIFT+0 ------  To English (United States) - US
        - CTRL+SHIFT+0 ------  To Chinese (Traditional, Taiwan) - Microsoft Quick IME
    Under Control Panel > Region > Advimistrative > Change System Locale...  change to Chinese HK SAR for non-unicode programs
    Control Panel\Appearance and Personalization\Display > Change the size of all items, use custom 123%.
    Control Panel\Appearance and Personalization\Display > Update Text size to 8 for Title bars, Menu, Message Boxes, Icons, Tooltips
    I found this for the display scaling registry changes but it is for 125% and it uses 78 for the dword value, not sure about custom 123%.
    http://social.technet.microsoft.com/Forums/windowsserver/en-US/882f17a6-7465-4aa6-8cea-27aa37a28a4d/gpo-to-set-default-windows-7-display-scaling-to-125?forum=winserverGP

    Hi lilyl,
    According to your description, you would like to deploy some settings about language and display via GPO.
    According to my knowledge, the steps you provided are from Windows 8 clients. Based on my test, you can use the following methods to realize:
    Add Traditional Chinese HK SAR. Locate the registry key HKEY_CURRENT_USER\Keyboard Layout\Preload, and then add a String Value "next number"(which has not been used)=00000404.
    The region settings. Please refer to the similar post:
    http://social.technet.microsoft.com/Forums/windowsserver/en-US/ec6a290e-fc09-4be6-9f6a-1f532d338606/change-regional-settings-locale-settings-and-keyboard-layout-using-group-policy?forum=winserverGP
    The display settings. The post you provided tells us the related registry keys, and you should try to find the right value since you want to custom it.
    In addtion, please refer to the following article to learn to deploy a registry item:
    http://technet.microsoft.com/en-us/library/cc753092.aspx
    Regards,
    Lany Zhang

  • IE 11 zoom default 125% based on display settings in control panel.

    Using Windows 7 Enterprise with 2 displays I have my display settings set to increase windows objects and text by 125%.  IE 11 appears to compound this by defaulting to 125% zoom on startup default.  If I set the display
    control back to 100 the default on IE goes back to 100% as well.  How do I get IE to default to 100 when the display is set for 125% Based on another post I checked IE ZoomFactor in the current user key and found it to be the recommended 100000.
    and ResetTextSizeOnStartup and ZoomOnStartup are set to 1.  Changes to these does not seem to have an effect.

    Hi,
    I test the issue and have the same result as yours, the value of ZoomFactor remains 100000. As a workaround, I change the value to Decimal:80000 (or Hexadecimal: 13880) then F5 to refresh the registry, reopen IE, it goes back to 100%, my registry setting
    as below
    [HKEY_CURRENT_USER\Software\Microsoft\Internet Explorer\Zoom]
    "ZoomDisabled"=dword:00000000
    "ResetTextSizeOnStartup"=dword:00000000
    "ResetTextSizeOnZoom"=dword:00000001
    "ResetZoomOnStartup"=dword:00000001
    "ResetZoomOnStartup2"=dword:00000000
    "ZoomFactor"=dword:00013880
    Yolanda Zhu
    TechNet Community Support

  • How do go back to my default display color settings?  Just bought Spyder 3

    Hello out there in Genius land...
    I just purchased Spyder 3 Pro to calibrate my display monitor, but in order to do this correctly, I need to go back to my default color display settings.
    I have manually calibrated my display several times in the past in the advanced mode, so I am familiar with this process, but I am unable to figure out how to go back to the default. Can't find a default option in the color settings tab.
    Any assistance in this matter would be greatly appreciated.
    Thanks,
    Anneita

    Thank you for your quick response.
    I just checked mine since I never changed it. It shows I have two default color >displays - Color LCD.
    When I select either one, the "Delete Profile" button is grayed out. This would >indicate to me that you should also still have your "default" color profile >showing.
    Hmmmm....
    Good point about the grayed out "Delete Profile" button. I went back into my "Color" tab to check it out, and I have 4 different profiles listed:
    - 12-30-10
    - 7/29/08
    - Color LCD
    - Color NTSC (19530 Calibrated
    When I click on each of them, they show a totally different display color.
    The only one that the "Delete Profile" button is not grayed out is 12-30-10, which I made on that date. The other 3 delete buttons are grayed out. But I am thinking that my actual default may be the one that says "Color LCD" like yours.
    Is that safe to assume? What do you think?
    Thanks,
    Anneita

  • Fn F7 defaults from Presentation on Projector and Notebook back to My Normal Display Settings

    I am using my T61 to project slides in class. When I connect it to the data projector, turn on the data projector, and use Fn F7 to switch from My Normal Display Settings to Presentation on Projector and Notebook, the signal does not get through to the projector. When I check Fn F7 again, I see that the scheme is back to My Normal Display Settings. What am I doing wrong?
    David

    Yes, I experienced the same problem. In my case it was caused by the VGA cable. After replacing the installed cable with a high-quality cable, the projector display was stable.
    Interestingly, my old HP notebook worked fine with the projector and the installed cable. The problem occurred only with my new T61. Maybe the electrical characteristics are slightly different, or a specific signal which was not used by the old VGA interface was degraded. I use a cable with pin 9 connected. I have not tested a cable without pin 9.
    Hope this helps, Carsten.
    Message Edited by cr on 12-08-2008 09:27 AM

  • Display Settings - Restore Defaults?

    Apple 20" Studio Display and G5 running Tiger.
    Out of nowhere my screen became substantially brighter but only for colors that are grey or silver. Then of course I messed around with the display settings and now I cannot see silver or grey colors since those colors were washed out to white.
    Since I cannot figure out how to return the display settings back to what they were initially, I just want to restore the original or factory display settings.
    Does anyone know how to accomplish this feat?
    [email protected]

    Hi
    System Preferences>Displays>Display is where you can change the resolution of your screen.
    Also, you can zoom in on webpages & other windows by using your mouse's scroll wheel whilst holding down ctrl key.
    Have a look in System Preferences>Universal Access>Seeing & check that Zoom isn't activated (Cmd-Alt-8 is shortcut).
    Steve

  • Monitor says VIDEO MODE NOT SUPPORTED after changing display settings

    HELP! I am about to have a nervous breakdown with my mac mini! I hooked up the mac to my Philips LCD via DVI. No problem at all. But because the screen is only 15" I wanted to play around with the display settings a bit. So I changed the resolution from it's original 1204x768 to the one higher (not sure of numbers) and to my HORROR, I now can't get any picture at all - it says "VIDEO MODE NOT SUPPORTED". I have tried everything I can think of. I have rest the P-RAM, I have unplugged all cables, plugged the back in again, I bought the mac into work and hooked it up to my monitor and changed the resolution back to 1024x768 which is what it was on originally and that STILL didn't work. I can see the Apple logo and then it goes black and comes up with the error message. HELP! What am I doing wrong - I can't believe one click of a mouse button has rendered my display useless!!!

    Welcome to Apple Discussions!
    Try booting the mini without the display connected, and then, once the system is running, connect the display. This will often force the system to default to a low resolution, and then correctly detect the display when it is connected.
    If that doesn't help, with the display connected, boot into safe mode (hold the shift key down when starting up) and once the system is running, change the resolution to 1024x768, and ensure the correct refresh rate is selected. Rebooting normally ought then to give you a good display.
    If all else fails, boot into safe mode with the display connected, and then in the Finder's file menu, use the 'find' option to search for 'windowserver' (no quotes). You should get 2 or 3 results, including one with a string of alphanumeric characters. Move all of them to the trash and restart normally.

  • Default printer settings for HP Deskjet 882c

    All I want to do is set this printer to print in black and white by default. If I wanted color, I would use my other printer ... I want faster than a snails pace so I brought this one back out.
    Being a PC for my entire life, this should be an easy thing to set the default print settings on the printer. I don't see them!
    What I am printing is emails off hotmail ... tons of them ... going back months ... so please don't ask me to add an additional step here ...
    Pulling my hair out here ... help would be lovely!

    You are on the right track for sure. The claim code is in fact printed in blue, so if your color inks are low or empty it will not show up. 
    I noticed there are 2 version of the 6500A, I will go under the assumption that you do not have the 'Plus' version since you didn't specify this, shouldn't be a big discrepancy either way (let me know if I am wrong).
    Viewing your ink levels is covered here, your Cyan ink cartridge could be empty : http://goo.gl/RjIhbp
    You can still find the claim code on the front panel of your printer without color ink. Go back to web services on your printers display and it will show your "*@hpeprint.com" email address. The prefix before the "@" is in fact your code.
    Also note that your code has most likely expired, which happens after 24 hours of being generated. Not a big deal. If your code has expired you will have to reset the web services in your printer, this will generate a new printer code. You can do this easily from the front panel of your printer.
    Follow this link and expand the section “What if I lose my printer code before registering?” under “Frequently asked questions (FAQs)”
    http://goo.gl/0WUyIe
    (*a note on step 4, some firmware updates may have simplified this entire step to be simply “remove web services”)
    After enabling the web services again the printer code area will still be blank if you are out of cyan ink. 
    Regardless the new code will display on the front panel (under web services).
    I hope this gets you going with ePrint. Let me know if you are having issues printing in color beyond this, or if you are still experiencing difficulties with ePrint.
    I work on behalf of HP.
    TwoPointOh
    I work on behalf of HP
    Please click “Accept as Solution ” if you feel my post solved your issue, it will help others find the solution.
    Click the “Kudos, Thumbs Up" on the bottom to say “Thanks” for helping!

  • Display settings

    Hi Experts,
    Is there any other classes available for display settings in ALV other than the below mentioned.The following classes doesn't works in SAP 5.0.
    Is this belongs to NetWeaver family?
    cl_salv_table
    cl_salv_functions
    cl_salv_display_settings
    Can any one pls help it out to do the same in abap objects?
    Regards,
    User

    Hello Raj
    If you are indeed working on an ECC 5.0 system then I do not see where the problem is. The following sample report <b>ZUS_SDN_CL_SALV_TABLE_DISPLAY</b> demonstrates how to adjust the layout of the ALV list. In addition, you see the coding for <i>event handling</i> and <i>column adjustment</i>.
    *& Report  ZUS_SDN_CL_SALV_TABLE_DISPLAY
    REPORT  zus_sdn_cl_salv_table_display.
    TYPE-POOLS: abap.
    DATA:
      gt_knb1        TYPE STANDARD TABLE OF knb1.
    DATA:
      go_table       TYPE REF TO cl_salv_table,
      go_events      TYPE REF TO cl_salv_events_table,
      go_columns     TYPE REF TO cl_salv_columns_table,
      go_column      TYPE REF TO cl_salv_column,
      go_display     TYPE REF TO cl_salv_display_settings.
    PARAMETERS:
      p_outlen       TYPE lvc_outlen  DEFAULT '20',
      p_title        TYPE lvc_title   DEFAULT 'New Grid Title'.
    *       CLASS lcl_eventhandler DEFINITION
    CLASS lcl_eventhandler DEFINITION.
      PUBLIC SECTION.
        CLASS-METHODS:
          handle_double_click FOR EVENT
              if_salv_events_actions_table~double_click
              OF cl_salv_events_table
              IMPORTING
                row
                column.
    ENDCLASS.                    "lcl_eventhandler DEFINITION
    *       CLASS lcl_eventhandler IMPLEMENTATION
    CLASS lcl_eventhandler IMPLEMENTATION.
      METHOD handle_double_click.
    *   define local data
        DATA:
          ls_knb1    TYPE knb1.
        READ TABLE gt_knb1 INTO ls_knb1 INDEX row.
        IF ( syst-subrc = 0 ).
          SET PARAMETER ID 'BUK' FIELD ls_knb1-bukrs.
          SET PARAMETER ID 'KUN' FIELD ls_knb1-kunnr.
          CALL TRANSACTION 'XD03' AND SKIP FIRST SCREEN.
        ENDIF.
      ENDMETHOD.                    "handle_double_click
    ENDCLASS.                    "lcl_eventhandler IMPLEMENTATION
    START-OF-SELECTION.
      SELECT        * FROM  knb1 INTO TABLE gt_knb1
             WHERE  bukrs  = '1000'.
    * Create ALV grid instance
      TRY.
          CALL METHOD cl_salv_table=>factory
    *    EXPORTING
    *      LIST_DISPLAY   = IF_SALV_C_BOOL_SAP=>FALSE
    *      R_CONTAINER    =
    *      CONTAINER_NAME =
            IMPORTING
              r_salv_table   = go_table
            CHANGING
              t_table        = gt_knb1.
        CATCH cx_salv_msg .
      ENDTRY.
    * Create event instance
      go_events = go_table->get_event( ).
    * Set event handler
      SET HANDLER:
        lcl_eventhandler=>handle_double_click FOR go_events.
      PERFORM adjust_column.
      PERFORM adjust_display.
      go_table->display( ).
    END-OF-SELECTION.
    *&      Form  ADJUST_COLUMN
    *       text
    *  -->  p1        text
    *  <--  p2        text
    FORM adjust_column .
      CHECK ( p_outlen > 0 ).  " In this case use default output length
    * Get columns instance
      go_columns = go_table->get_columns( ).
    * Get single column instance
      TRY.
          go_column  = go_columns->get_column( 'LOEVM' ). " delete flag
          go_column->set_output_length( p_outlen ).
        CATCH cx_root.
      ENDTRY.
    ENDFORM.                    " ADJUST_COLUMN
    *&      Form  ADJUST_DISPLAY
    *       text
    *  -->  p1        text
    *  <--  p2        text
    FORM adjust_display .
      go_display = go_table->get_display_settings( ).
      go_display->set_striped_pattern( abap_true ).
      go_display->set_list_header( p_title ).
    ENDFORM.                    " ADJUST_DISPLAY
    Regards
      Uwe

Maybe you are looking for

  • Battery charging & CPU heating issue

    i've change week ago late 08 White MB 2.4GHz to Unibody 2GHz and notise following: 1. charging time increse in average in 2 times (from 2hrs to ~4hrs) and last 1,5 hrs avrg takes progress from 90% to 100%. i found it very strange becouse unibody batt

  • Good color monitor for use with FCP

    I'm looking for a color monitor that has dvi and S video inputs.

  • Sales order field Non Editable

    Dear All, how to make  sales order field -payment terms non editable to the end  users we do not want the endusers to change the payment terms proposed from the customer master With regards Mohammed Raees

  • REGARDING ABAP CODE IN ECATT

    HI    HOW TO WRITE ABAP CODE IN ECATT TESTING FOR IF VENDORNO DOES NOT EXIST IT SHOULD NOT DISPLAY THE VENDOR SCREEN.         PLZ HELP ME I WILL BE THANKFUL

  • Skype 7.3 crashes whenever connected

    I've done a little bit of research on the forums but is still unable to fix my issue I am running Windows 7, Skype is 7.3 (the latest version available as of 4/4/2015). Every time when Skype starts, it will "stop working" if it is able to connect to