Default username and password not found

Hello all,
Just bought the new WVC54GCA ip camera, tried to configure it with its setup but can't get in as I couldn't find the admin password anywhere.....Does anybody know what are the default settings for these username and password fields?
(Linux, MInt, Firefox...)
regards

Default Username is admin and default password is admin...However, if it does not work then you need to enter the password that was set when you installed the camera for the first time...If you don't remember the password then you need to reset the camera and re-configure it...

Similar Messages

Aironet 1100 Default Username and Password not working

I have a Cisco Aironet 1100 series access point (AP1120B) that after resetting to factory defaults the default username and password (Cisco and Cisco) aren't working in the web GUI. I am able to telnet to the AP's IP and log in with Cisco and Cisco but don't know the ENABLE password. I have tried Cisco and cisco and everything else i could think of with no luck. any help would be appreciated.
I also have a Cisco Aironet AP1242AG that is doing the same thing.

Hi Rich,
I assume that you are using the mode button to reset the configurations on these units -- this procedure *should* reset all credentials to Cisco.
If this is still not working, you can try the following:
1) Connect console port and power-cycle unit
2) When IOS starts loading, hit ESC key twice to get to the boot-loader prompt
3) At the boot-loader prompt show a directory of the flash filesystem (dir flash:)
4) Delete or rename the files "config.txt" and "env_vars", then boot the system ("delete flash:/config.txt" "delete flash:/env_vars")
-Patrick Croak
Wireless TAC

WSN 1.2 NI 9792 Security: Initial Setup? Default Username and Password?

Hello,
With NI WSN 1.1, using a 9792, I can click the Set Permissions button and if none had been set it would simply ask me for a new administrator password. Now, with NI WSN 1.2, when I click on the Set Permissions button it takes me to the 9792's web interface and says "Either no one is logged in or you do not have permissions to view/edit users, groups, and permissions." When I click the Login button, a box pops up and asks me for both a username and password. I scoured the release notes, help files, and the internet and it seems there is NO documentation on how to setup the very first username/password combination nor does it state what default username/password combination there might be. I also tried a brand new 9792 straight out of the box and loaded 1.2 on it and it has the same issue. Is there something obvious that I'm missing? How does someone initially set up security on the 9792?
Solved!
Go to Solution.

Hello Garrett,
Thanks for your post!
It looks like you are needing information on how to find out the log in information of your 9792. When using NI-WSN 1.1 we allowed users to set the initial password and this is still the case for the 9791. The 9792 is a NI-WSN node gateway as well as a LabVIEW Real Time target. Its default log in information can either be found in a Knowledge Base (KB) the LabVIEW help or MAX help. Are you using LabVIEW 2009 SP1 or LabVIEW 2010?
The default user name and password is the following:
username: admin
password: <blank>
KB
Default Username and Password to Log into a Real-Time Controller
http://digital.ni.com/public.nsf/allkb/14D8257A7724BE85862577F90071B73F
LabVIEW Help
Start >> All Programs >> National Instruments >> LabVIEW xx >> LabVIEW help
then go to .. Fundamentasl >> Working with Prjects and Targets >> How-To >> Monitoring and Configuring a Remote Device from a Web Browser
MAX Help
Open MAX >> Help >> MAX Help (can also press F1 in MAX if open)
then go to .. MAX Remote Systems Help >> LabVIEW Real-Time Target Configuration >> Device Configuration >> Logging into your System
The LabVIEW help link above is called out in the 9792 getting started guide under Related Documentation that directs you to the LabVIEW help.
NI Wireless Sensor Network Getting Started Guide
http://www.ni.com/pdf/manuals/372781c.pdf
Is this the information that you were looking for? Please indicate if there is anything else we can do.
Cheers
Corby
WSN R & D PSE

Default username and password Oracle Hyperion workspace/shared services

Hi Friends,
I had installed Install Oracle Hyperion Planning, Fusion Edition Release 11.1.1.3.0 (foundation services and planning)
but i am unable to login to workspace,shared services
what is the default username and password for these.Please let me know?
Regards,
DB

Hi,
Default Admin user is: admin and default PW: password.
If you have not yet changed.
Thanks
Focusthread Hyperion Trainer
[http://focusthread.com/training]

What is the default username and password for administering my f4500 deskjet printer?

I need to administer my F4500 Deskjet through my web browser, but do not know the username and password. I presume there is a way to default the settings, but I need to know the defaults. Please provide the default username and password for web access.
Thanks.

The default username is Admin, but the password is blank by default. Somehow, a password was added at some point.
You can try going to the EWS and going to Settings and looking for a password reset option in the Administrator Settings section. If it is there, it will be the only way I know of clearing the password on this particular printer.
↙-----------How do I give Kudos?| How do I mark a post as Solved? ----------------↓

Default username and password for BPEL Console

What is the default username and password for BPEL Console?

Hi,
can you provide the version which you have installed?
10.1.3 / 10.1.2?
Advanced installation?
oc4jadmin or bpeladmin as user
welcome or welcome1 as password (i do not remember exactly)

1042N-A-K9 Default Username and Password

I just recieved in the mail an aironet 1042n ap. It was assigned an ip of 192.168.1.254 by my router. When I attempt to connect it prompts for a password and states the default username and password is admin and 1234. It will not except this, or Cicso and Cisco, or cisco and cisco. Does this mean it's doa? Any ideas? Also does this require a wlan controller?
http://www.newegg.com/Product/Product.aspx?Item=N82E16833120659

Have you tried via the serial port?
The config guide says Cisco/Cisco on the HTTP server, but I've seen the admin / Cisco before.
http://www.cisco.com/en/US/docs/wireless/access_point/1140/autonomous/getting_started/guide/ap1140aut_getstart.html#wp35957

Log in with default username and password

Is there a way to create a pdf so that it automatically logs in with a default username and password so that the user is not prompted upon opening?

No, there is no way set a default user name and password, but as an alternative you can set your policy to be "Anonymous Access", meaning that there is no authentication (of the user) required to open the document, but you can still control (i.e. prevent printing) what the "anonymous" user can do to\with the document.
Regards
Steve

Default username and password for NSAdmin

Hi!
trying to configure the ZfD Middle Tier Server with NSAdmin using:
http://myserver/oneNet/NSAdmin
I am asked for a login and password, but in the manual it doesn't inform
what's the default username and password.
Can someone helpme in this?
Fabio Martins.

Fabio,
It appears that in the past few days you have not received a response to your posting. That concerns us, and has triggered this automated reply.
Has your problem been resolved? If not, you might try one of the following options:
- Do a search of our knowledgebase at http://support.novell.com/search/kb_index.jsp
- Check all of the other support tools and options available at http://support.novell.com in both the "free product support" and "paid product support" drop down boxes.
- You could also try posting your message again. Make sure it is posted in the correct newsgroup. (http://support.novell.com/forums)
If this is a reply to a duplicate posting, please ignore and accept our apologies and rest assured we will issue a stern reprimand to our posting bot.
Good luck!
Your Novell Product Support Forums Team
http://support.novell.com/forums/

Default username and password for WebDB

Hello,
i need to know what is the default username and password in formsserver and webdb
can some one help
thanks in advance
Tarek

I think you meet the same problem that I had fix.PLS set connect
string in http://yourhost:yourport/webdb/admin_/gateway.htm,This
step must be done!!I think this version Webdb use SQL*NET to
connect DB.
Guest (guest) wrote:
: I did run it as root and oracle but no luck there!
: Luis Claudio (guest) wrote:
: : Hi,
: : try doing this as root :
: : # wdbstart www.yourdomain.com <port> &
: : I think it works, ok? :)
: : Luis Claudio
: : guest (guest) wrote:
: : : same problem. on the other hand, it is possibel to go to
url
: : : http://www.mydomain.com:port/webdb/admin_/ and you can
: : : manage seetings in this page. as a result, wdlistener is
: : : running, but still have a problem.
: : : any idea?
: : : Guest (guest) wrote:
: : : : Hello, all! I installed webdb, but when I try to do
: : : : http://www.mydomain.com:port then it prompt me for a
: username
: : : and
: : : : password. I put in username: webdb password: webdb
: (default)
: : : and
: : : : then it gave me a message saying "Database login failed"
: Any
: : : : ideas please???
: : : : NOTE: I didn't start the webdb listener yet, same as
: : tnsnames.
: : : : Is it neccessary? I don't know! I had listener started
: for
: : : : ORACLE 8i.
null

Default username and password for acs 3.2.3

Hi All
What is the default username and password to login to a newly built ACS Server V3.3.2 ?
Thanks in advanced.
Darren

Darren,
You need to log in to ACS on the console of the Windows server (assuming it's not an ACS Solution Engine). If you do that, http://localhost:2002 it should take you straight in with no username/password prompt. Once in you can setup admin users and access from other boxes.

Default username and password for newly created client in minisap

Hi all,
I am using the free SAP minisap provided by SAP. In this system i tried to create a user from tcode scc4 . when i try to login to the new client with the username SAP* and password minisap i am not able to login. What will be the default username and password for the newly created client in minisap.

In the new installation
The parameter
login/no_automatic_user_sapstar is set to " 1"
You create the parameter with value "0" & restart application server.
& Try to login into New client as SAP* with password "pass" - ( For a Standard System) - I don't what will be the default password in minisap.
Rgds
PR

Default username and password for 10g

hey guys does anyone noe the default username and password for the sql plus? version 10g

SQL*Plus does not need a username and password. E.g.
/home/oracle> sqlplus /nolog
SQL*Plus: Release 10.2.0.1.0 - Production on Tue Oct 3 14:31:43 2006
Copyright (c) 1982, 2005, Oracle. All rights reserved.
SQL> prompt Hello World
Hello World
SQL>
Connecting to an Oracle database instance usually requires one to supply Oracle database authentication, e.g. a schema name and password. Unless of course the database uses external authentication in which case you do not need to manually specify an Oracle schema name and password.
Yes, using SQL*Plus as a client to connect to an Oracle database server typically requires a scheme name and password.
It is important to understand the difference - SQL*Plus is a CLI (Command Line Interface) client to Oracle. It is not the database. SQL*Plus does not need a username or password to load and use.
Granted, it is not of much use when not connected to an Oracle instance, but that does not change the point that SQL*Plus itself does not need authentication.

For the 1st time I am trying to send an iPhoto by email but get an error message "combinations of username and password not recognised" I use the same details to log on to my Sky Mail (yahoo mail ) account . Any ideas?

For the 1st time I am trying to send an iphoto by e-mail but get the error message " combination of username and password not recognised by the server" I use Sky Mail ( yahoo mail) and input the same username and password that I access Sky Mail - have retried many times. Predictably the Sky help desk have no idea. Can anyone help please?

I regret that you're having trouble setting up your email, corbad! You're on the right track with your incoming email address. You might also try incoming.verizon.net or incoming.yahoo.verizon.net as possible alternatives, and 995 as the port number. Please let me know how that goes!
DionM_VZW
Follow us on Twitter www.twitter.com/vzwsupport

BPM Default username and password

Hi Experts,
Will anyone please help to find the bpm composer default username and password to log into bpm composer. i installed bpm and trying to login with weblogic/welcome1. response is invalid ID and password. please help me out.
Thanks
SN

Usually you have to set the standard weblogic username and password at install time. Common "default" combinations are weblogic/weblogic1, weblogic/welcome123, weblogic/welcome1, weblogic/oracle, weblogic/oracle123. But there really is no "default" as it is dependent on whatever you have indicated during the install. Many prebuilt VMs from Oracle will use one of the combinations that I mentioned though.
But if none of those work, you can change the weblogic password in WLS console --> Security Realms --> myrealm --> Users and Groups as already mentioned by the previous reply.

Default username and password not found

Similar Messages

Maybe you are looking for