Deleting an Integration Model.

hi Guys
               if any kind of changes happens in master data in ECC then we transfer that data in SCM,then what happens with that planning data with which we work earlier.
And Deleting an integration model does not mean that the previously selected data in APO is also deleted.what happens of that data.
thank u
karan
Edited by: karan.sap on Feb 27, 2010 6:36 PM

Hi Karan,
1) if any kind of changes happens in master data in ECC then we transfer that data in SCM,then what happens with that planning data with which we work earlier.
As and when you activate an integration model, a new integration model gets
generated and the earlier one will get deactivated.  (provided the model name,
model selection criteria are same).  That means the newly changed master data
will get activated to SCM system in which the old change is obsolete.
2) And Deleting an integration model does not mean that the previously selected data in APO is also deleted.what happens of that data
Whenever a new model gets generated, the old model will be there in the system
only and that inactive models needs to be deleted at frequent intervals orelse
it will add inconsistency to the system.  This will be done using CFM7 transaction
by selecting inactive models indicator.  Whether the old model is deleted or not, but
system always will read and plan as per the newly activated model.
Regards
R. Senthil Mareeswaran.

Similar Messages

  • Unable to delete/create integration models.

    Hi All,
    I need to correct some int.models wrt the logical system.
    1)     CFM1 u2013 choose variant pops up a msg- logical system not maintained in NDV2. This is not  supposed to be maintained. I need to change the variant models for a different logical system that is maintained in NDV2.
    2)     CFM7- delete all models.- I am unable to delete the models even after making them inactive.
    Final objective is to delete all the models- active and inactive and recreate new ones as nomenclature needs to be same. I canu2019t maintain the wrong (present) logical system in img, that's seen in the IM variants that do not lend themselves to change. The moment i do CFM1 it pops up a an error screen referring a wrong logical system..
    Pls., guide step by step.
    Regards,
    Lok

    Thanks Lakshmi,
    I began on the same note as wass evident but i did not have the wb request auth required. so was thinking if there is another was out fiddling with user transactions of IMs
    Thanks for prompt reply. Awarded full 10 points.
    Regards.
    Lok

  • Manual Reservations Integration Model

    Hello All,
    In our project, during Go-live we dint had manual reservation Integration Model Activated due to some business reason. 
    whenver a process order is created in R/3, Reservations for Components appear in R/3 and APO.
    Now when the components are good Issued in R/3 during Finished Product Process Order, these dependent reservations are not deleted in APO though the stock is reduced. Upon analysis we found that by activating the Manual Reservation Integration Model , these reservation will be deleted and hence both the R/3 and APO System will be in sync.
    Now the Problem is when we are trying to do this manual reservation Integration Model activation through Batch Job , activation is taking a very long time. Upon further analysis we found that for the material-Plant combinations, program tries to search records in table RESB and approximately it takes around 5 minutes for each material -plant combinations. In our integration model we have around 2400 Material-Plant Combinations. CFC3 settings for Reservations are select block size of 1000 and filter block size of 512. R/3 version is 4.7.
    Table entries in RESB are close to 3.5 Million with 141 Extends.
    So just wanted to check with you guys if anybody has experienced this problem before and what resolutions were put in place to addres this ? Are there any SAP Notes available ? I searched but could not found any.
    also what would be the best way to go forward? Some of the options i could think are
    1) Run the I.M for selected material-Plant Combinations
    2) Run the I.M for generic selection Criteria ( i.e AS IS) during Weekend.
    Pls share your opinions.
    Regards,
    Pawan.

    Hello Kenneth,
    As i understand from your message that if a final Issue Indicator is unchecked, then those reservations should be present in APO. However i got confused with your below statement
    Therefore it is neccessary that reservations with final issue indicator set are available in APO.
    I think you might be trying to tell  reservations with final issue indicator unchecked ( and not SET) are available in APO.
    Regarding Transaction Code MBVR, I have few queries
    1) Does this T-CODE MBVR sets the deletion Indicator in Table RESB or does it delete the Reservation permanently from Table.
    2) I am not able to locate Completed Items field, which will enable me to delete Reservations. Can you pls let me know the field name.
    Pls note that whenever i am trying to delete reservations thorugh t-code MBVR, it gives a message " No Document exists for the Speficied data".
    thanks for your assistance,
    Pawan.

  • CIF Queues generated without active integration model

    Hello All,
    We are facing a unique issue, where queues are seen in SCM queue manager although those products are not there in any active integration model for transaction data.
    The scenario is as follows:
    1. We are CIFing only master data as we have only DP and release to R/3
    2. There is active integration model for master data
    3. There is no integration model for transaction data
    However in SCM queue manager, I am seeing queues of type CFFCC "Location" "Product".
    The function module name is /SAPAPO/CIF_IRQ_REDUCT_INBOUND.
    We observed in R/3 that the goods movement transaction code MB1A is trigerring TRFC's which is generating the queues.
    Has anyone encountered a similar scenario like this?
    Regards,
    Kedar

    Oi Jackeline!
    Hello, all!
    I think Vikas got the point, but let me be more specific...
    The transfer of requirement reduction depended in previous releases (until PI 2002.1) only on an integration model for material master data being active. Then a new type of integration models was created to control the sending of requirement
    reduction.
    To activate the new logic a flag has to be set in customizing.
    Use transaction /CFC9
    OR
    R/3 SAP Customizing Implementation Guide
    -> Integration with Other SAP Components
    -> Advanced Planning and Optimization
      -> Application-Specific Settings and Enhancements
       -> Settings and Enhancements for Requirement Reduction
        -> Evaluate the Requirements Reduction Filter Object Type:
    Then, flag 'Filter Object Requirements Reduction'
    If you set this flag no queue of type CFFCC* will be sent if there is no explicit active integration model for Requirements Reduction. Please set this flag in production and delete any existing queues of type CFFCC*. No new such queues should be created in the future as long as you don't activate the transfer via an integration model.
    I hope this information helps to clarify this issue.
    Please give your feedback concerning the given solution.
    Thank you!
    Will

  • Integration model activation issue - After Prod to Quality refresh of R/3

    Hi Guys,
    Our R/3 quality system refreshed from production. Hence all the integration models Logical system pointing APO production system. Mistakenly I deactivated all the integration model in R/3 Q system which having APO Production logical system.
    All the IM in R/3 quality system are inactive. When try send material getting error message "relavent location doesn't exist".
    For that try to move the Location getting error message "Location already exist in APO Quality" system.
    Now I want to active the all the Plant, material.etc integration models. Please let me know if any more information and help to overcome the issue.
    Thanks,
    Saravanan V

    Saravanan
    Make a table level change and set the integration model flag as active in the table CIF_IMOD. This will help you solve the issue .
    Go to transaction SE16 . Give table name as CIF_IMOD. Give the name of you integration model and execute . Now all versions of that integration model will be displayed ( this will happen if you have many inactive versions and do not have the RIMODDEL program to delete inactive IM's) . Choose the latest version and go to change mode  and set the value of "Entry is active"  (technical name ACTIVE) field to  I.
    You can take help from development team if you do not have authorization to SE16
    Thanks
    Saradha

  • APO Integration model error

    Hi all
    when activating Integration model in R/3 with APO below error is coming
    "Outbound queue blocked"
    System:APOCLNT800,USER DDIC 09.02.2008 13:28:15
    Function:/SAPAPO/CIF_LOC_INBOUND
    Text:Host name: "XXXXXX"unknown/CPI-C error CM_Product.
    when we click QRFC monitor  lot of queues are there..
    can any boby give solution for this
    Regards,
    srihari

    Hi Somanath
    Our basis consultant checked   every thing in SM59  and he told every thing is ok.
    In QRFC monitor lot of queues are there how to handle/delete the queues   .. i tried  but not able to resolve.
    Regards,
    srihari

  • EWM CIF Integration Model master data transfer Issue

    Hi Gurus,
    I am not able to transfer the master data from ERP to EWM.
    When I excecute the transaction CFM1 and CFM2 integration model ,the material is not getting transferred.
    I am getting the below mentioned Error message.
    "Location does not exist for external location 9997, type 1040, and BSG CSSCMDEV"
    Please help me in resolving this issue.
    Regards
    Govind

    Hi,
    Thanks for the reply
    I had created the location 9997 for the location type 1001earlier.
    When I tried to delete the location and create new Location for Location type 1040.System is not allowing me to delete.Please let me know how to delete the existing Location.
    Regards
    Govind

  • Reactivating integration models

    Hello All,
    I deactivated a big sales order integration model in my production system. While trying to reactivate the RIMODAC2 program is taking huge time(30 mins) to complete for 5 part-plant combination. I have around 100K part-plant combinations.
    Is there a short cut to reactivate? If there is some alternate program to somehow reactivate the models.Any help will be greatly appreciated.
    Anyone ever had such a situation? Any ideas.
    Thanks and regards
    Sanjeev

    Hi Sanjeev,
    There is no short cut but I can explain you a way.
    First please confirm that only one transaction data integration model was inadvertantly deactivated.
    Second - the steps I mention below should be carried out with "care" and after notifying business users suitably as you have to do this when there is mimimal activity in the system.
    Broad steps:
    1. Stop the CIF Queue by going into /SAPAPO/OM17
    2. Activate the sales order integration model
    3. There should be queues created inbound to your SCM/APO system (check in SMQ2)
    4. Wait till all queues are created for the Sales Order Integration Model and make sure you see the CIF_GEN_EVENT queue (last queue which after going to SCM system returns to R/3 ERP system and marks the Integration Model as active)
    5. Delete all the CIF queues for the Sales Order Integration Model except the CIF_GEN_EVENT queue.
    6. Start the CIF Queue - the CIF-GEN_EVENT queue should process
    7. Confirm that the Integration Model is activated in R/3
    8. Run Delta Report (/SAPAPO/CCR) and resolve any differences
    Disclaimer: This is not a SAP documented solution.
    Hope this helps and works out for you.
    Thanks,
    Somnath

  • Problem with activating integration model

    When I am trying to activate an integration model, that includes a scheduling agreement (type LF), the activation isn't successfull. It isn't blocked, but it never stops.
    In the screen I have a message called "determining delta model" but it never continous with executing the activation.
    Does anybody know what could cause this problem?
    thanks in advance
    Mark Smeets

    Hi,
    I am facing the same problem as mentioned in the original post.
    Whenever I activate the integration model for vendors, a "CIF_LOAD" window appears with message "Should interval be created" with YES and NO option. Why does this window appears. After clicking on NO option the message "Determining delta model" appears in the status bar and after some time the program gets terminated due to time out.
    I have tried following solutions mentioned in this thread.
    Refreshed the indexes of the two tables BDCPS and BDCP using DB20.
    Executed the transaction BD22 in test run mode, but I am not sure which change pointers option(obsolete or processed) to select for deletion and also which message type. I selected the obsolete option but here too the program got terminated after time out. Besides I am doing this on prduction environment and other integration models like plant etc got activated.
    Please help us with this.
    Regards,
    Gaurav Patil

  • Problem with activation of integration model

    Hi,
    I am facing a problem. Whenever I activate the integration model for vendors, a "CIF_LOAD" window appears with message "Should interval be created" with YES and NO option. Why does this window appears? After clicking on NO option the message "Determining delta model" appears in the status bar and after some time the program gets terminated due to time out.
    I have tried following solutions.
    Refreshed the indexes of the two tables BDCPS and BDCP using DB20.
    Executed the transaction BD22 in test run mode, but I am not sure which change pointers option(obsolete or processed) to select for deletion and also which message type. I selected the obsolete option but here too the program got terminated after time out.
    After this I selected  the message type "CREFET" (Get Vendor Data), "CRECOR" (Core vendor master data distribution), "CREMAS" (vendor master data distribution) but there were no change pointers for this message type.
    Besides I am doing this on prduction environment and other integration models like plant etc got activated.
    Please help us with this.
    Regards,
    Gaurav Patil
    Edited by: Gaurav Patil on Sep 29, 2008 12:35 PM
    Edited by: Gaurav Patil on Sep 29, 2008 12:36 PM

    Hi Gaurav,
    Please split the volume in multiple jobs and see wheather it is running fine or not ?
    Also please check CFG1 log on R/3 side .
    Also check SLG1 log on APO side .
    Manish

  • Excluding a specific material from integration model

    Hi,
    All materials corresponding to a particular MRP type are in an integration model and the model is active.
    Request you to inform the steps to exlude a specific material from this integration model even if it is having the same MRP type.
    With regards,
    Mrinal

    Mrinal,
    CFM1>For each model affected, call up the affected variant.  Go to the material field. Select Multiple selections ('right arrow'). Select the 'Exclude values' tab (third tab).  Enter the material or materials to exclude. Copy (F10).
    Save the variant.  Execute the program to generate the (newly modified) model.  Save the model.
    Go to CFM2.  Activate the newly generated model.
    Repeat for other affected models.
    If the material previously been contained in active models, then the newly excluded master and transactional data will still exist in SCM.  If you find it to be necessary to delete these data, then you need to go over to SCM and perform the necessary steps.  Start with /SAPAPO/CCR to delete transactional data, then go to WUF to delete master data.
    Regards,
    DB49

  • Integration Model for the resources terminates with an error

    Hi
    we have deleted the existing Integration model for the Resources and trying to create a newones, when iam activating the new resource integration model it is terminating with an error "Resource already exists(mapping error occured)".
    we did the consistency check for the resources and ran OM17 everything seems OK. when tried to the same in the test system it works fine...
    How to rectify this..

    5,
    Deleting integration models for master data is a poor way to start any process.
    The message implies that the offending resource probably was created locally in SCM, or perhaps to support a different Business System Group. The easiest solution is to delete the resource and then recreate via Core Interface.
    Best Regards,
    DB49

  • Integration model desnot exist

    Hi,
          I got a error in delta report with the message
    No active integration model exists in R/3
    Message no. /SAPAPO/CIF184
    The material in the plant has a change pointer "R". What does the "R" Change Pointers Exist with Method "Delete Complete Document" mean?
    Is it saying that the location product is scheduled for deletion? Is there a check box checked in APO for deletion??
    Also there is an active integration model with that product, location combination.
    What does the message mean then???
    Thanks.

    You can always check for deletion flags in table /SAPAPO/LOC (check for deletion flag field LVORM) and /sapapo/MATLOC (check for deletion flag field LVORM)
    Change pointer R means Completely Delete Document. This happens when someone deleted an order in APO and the same order deletion has not yet transferred to R3 due to some reason. The reason could be that you have set up change pointers in the system to stop automatic deletion transfer of orders or the fact that integration model does not exist.
    So either make sure you have an active integration model setup for the product or get rid of the change pointer using /sapapo/c5 transaction

  • Integration model generation

    Hi,
             We have a integration model for master data- Schedule lines and contracts. We have a background job that generates and activates the model. If I regenerate the model in CFM1, does it hurt anything for the job?
    I think every time you generate a model, a new model will be generated right? Does this cause any discrepancy?
    Thanks.

    There are two types of sending data to APO through CIF
    1) Sending only changes (Delta)
    2) Sending everything (Delta+ New creation).
    Considering there are three materials which changed on a certain day then just activating the IM model will work perfectly fine.
    If along with three materials there was also an addition of a brand new material in R/3 . Then only by generating the Integration model will not help .
    You will have to delete the original IM and recreate the same IM by using variants then activate the IM. By doing so it will consider as a initial transfer and send all the three old materials and the brand new material changes to APO.
    If you feel it is useful pelase reward points.
    The reason behind this behaviour : When you try to activate already existing IModel, then it only activates those objects which are already been generated and present during the generation of the IM.
    So if a new material is created you will need more than just to generate. You will have to delete the model, generate the model, activate the model.
    Thank You
    My
    Thanks,
    My

  • System copy:integration models altered

    Hi SCM experts,
    We have APO 4.1 connected to ECC system.Recently the QAS data is refreshed with PRD data and after that all CIF integration model variants in QAS are pointing to PRD system. There are more than 100 integration model variants and changing the logical system mnaualy to QAS client is taking long time.
    Is there any standrad report or t.code by means of which we can do a mass maintenance of these integration model variants ?

    Hi deeparai,
    You can change the name of logical system in ECC table CIF_IMOD. However, the integration models will not become active unless you generate them again (CFM1/2/3).
    Hope this helps in reducing manual work.
    regards,
    biplab

Maybe you are looking for

  • MB_CUR_MAX Settings in Solaris 10

    Hi All - MB_CURR_MAX sets to 3 in my Solaris 10 though it is not a multi-byte machine. The Locale settings are set to en_GB.ISO8859-1. I do not know if this setting will cause some system calls, functions to behave differently. How is this set? I che

  • Weekly Breakdown Analysis

    Dear All, We have MCI7 report where we can have monthly breakdown analysis but here my requirement is, I want to have report on Weekly Breakdown analysis. To get the Weekly Breakdown analysis we can change the update period for info structure S070 to

  • Mail port settings not sticking

    I'm having trouble with port settings not sticking in mac mail.  When I start Mac Mail (v5.1, running in Lion) the program won't read mail in my iCloud account because the port settings are incorrect (port 143).  I click on the "Use SSL" box, which c

  • Custom directories for export/import for Integration Builder

    Hi, XI uses default directories for exporting and importing Integration Builder objects, and there is no option to change the directory or to pick up objects from another directory. Does anybody know of any way we can change the default directory tha

  • Is Wily a part of SMD? / Or are this two seperate Applications?

    Hi there, just a question... Is Wily a Part of SMD... or is Wily an application beside SMD? Regards Bjoern