Design Controler 5508 & 5760 Compatibility - N+1

Hello,
I've 5508 WLC and adding a new 5760..
I know, it's possible for this 2 to be in the N+1 model (version 7.6)
If the 5508 or 5760 goest down, the AP previously associated to the failure controler, need to re-download the image to join the active controler.
Is it expected to change this constraint image reloading ? If yes, when ?
This is still a Cisco Validated architecture ?
Tks a lot.
Bye.
David

Unfortunately these 5760 & 5508 AP images are not exactly same. So if fail-over occur AP has to re-download the image.
Yes, this has to be fixed, but not sure when.
Also there is no CVD for anything related to converged access, very bad indeed
HTH
Rasika
**** Pls rate all useful responses ****

Similar Messages

  • Report Designer Control - Redistribution Issue

    Hi:
    I use Report Designer Control(RDC) in my program to allow user to modify reports.  I made a build and installed the build but when I try to access report designer from program I am getting the error about license. 
    "This system does not have a valid license, or the evaluation  copy of the license has expired. Please contact Business Objects to obtain a Report Design Control license."
    I do have valid KeyCode for RDC and i am supplying the same for the merge module too.
    My Development Environment
    Operating System            :     Windows XP (SP 2)
    IDE                                 :     VS 2005 Professional
    Crystal Reports                :      XI Release 2 Developer
    Deployment Software        :      InstallShield 12 Premier
    Can anyone please tell me why I am getting above message, I can able to distribute Report Designer Control with Crystal Reports 9 version without any problems, but it is not working with Crystal Reports XI.
    Thanks in Advance,
    Sriram.

    Hello,
    The Report Designer Component (RDC) was never designed to work in Visual Studios .NET.  This is because the RDC is an ActiveX COM component and Microsoft has been moving away from ActiveX.
    It is also my experience that RCAPI applications - "to allow user to modify reports" - will not work in a Visual Studios application.
    It is possible you're getting your error if you had an original CR XI (v11.0) keycode and upgraded to CR XI R2 (v11.5).  Original CR XI (v11.0) keycodes will not work. CR XI (v11.0) keycodes do not "unlock" RCAPI functionality in CR XI R2 (v11.5).  If you upgraded from CR XI (v11.0) to CR XI R2 (v11.5) you likely have an original CR XI (v11.0) keycode.  You will need to get a new CR XI R2 keycode from Business Objects.  You can contact the Customer Care team by email - customercareamericas @ businessobjects.com (rebuild the email address) - or by phone - 800-877-2340, option 5.  If they need additional information you can ask them to contact me.  I'm on the Developer Support team and they should be able to contact me internally.
    If you have an original CR XI R2 (v11.5) keycode please make sure to update to at least Service Pack 2 and download updated RDC merge modules from the [Business Objects Software Download Page|https://websmp230.sap-ag.de/sap(bD1lbiZjPTAwMQ==)/bc/bsp/spn/bobj_download/main.htm].
    Please remember that even if you get a new, original CR XI R2 keycode, and/or update your merge modules  you may still not be able to get your VS2005 RCAPI RDC application working.
    Sincerely,
    Dan Kelleher

  • I cant not control wlc 5760 (every thing CLI & GUI)

    After wlc 5760 reload (because of some problems.)
    I don't know this message. and I can not control wlc 5760 in CLI console.
    Please help me.
    %Error opening tftp://255.255.255.255/network-confg (Timed out)
    %Error opening tftp://255.255.255.255/cisconet.cfg (Timed out)
    %Error opening tftp://255.255.255.255/nx-5760-wlc01-confg (Timed out)
    .... again & again
    I try to booting. but I can't.
    I want to know : method 5760 Factory default or normal booting mode.
    + log
    FIPS: Flash Key Check : Begin
    FIPS: Flash Key Check : End, Not Found,FIPS Mode Not Enabled
    This product contains cryptographic features and is subject to United
    States and local country laws governing import, export, transfer and
    use. Delivery of Cisco cryptographic products does not imply
    third-party authority to import, export, distribute or use encryption.
    Importers, exporters, distributors and users are responsible for
    compliance with U.S. and local country laws. By using this product you
    agree to comply with applicable laws and regulations. If you are unable
    to comply with U.S. and local laws, return this product immediately.
    A summary of U.S. laws governing Cisco cryptographic products may be found at:
    http://www.cisco.com/wwl/export/crypto/tool/stqrg.html
    If you require further assistance please contact us by sending email to
    [email protected].
    cisco AIR-CT5760 (i686) processor with 10485760K bytes of physical memory.
    Processor board ID FOC1746V2AK
    2048K bytes of non-volatile configuration memory.
    10485760K bytes of physical memory.
    255000K bytes of Crash Files at crashinfo:.
    3612840K bytes of Flash at flash:.
    0K bytes of Dummy USB Flash at usbflash0:.
    0K bytes of  at webui:.
    Base Ethernet MAC Address          : 1c:1d:86:24:10:80
    Motherboard Assembly Number        : 73-14448-04
    Motherboard Serial Number          : FOC174577NZ
    Model Revision Number              : A0
    Model Number                       : AIR-CT5760
    System Serial Number               : FOC1746V2AK
    %Error opening tftp://255.255.255.255/network-confg (Timed out)
    %Error opening tftp://255.255.255.255/cisconet.cfg (Timed out)
    %Error opening tftp://255.255.255.255/nx-5760-wlc01-confg (Timed out)
    %Error opening tftp://255.255.255.255/network-confg (Timed out)
    %Error opening tftp://255.255.255.255/nx-5760-.cfg (Timed out)
    %Error opening tftp://255.255.255.255/cisconet.cfg (Timed out)
    %Error opening tftp://255.255.255.255/nx-5760-wlc01-confg (Timed out)
    %Error opening tftp://255.255.255.255/nx-5760-.cfg (Timed out)
    %Error opening tftp://255.255.255.255/network-confg (Timed out)
    %Error opening tftp://255.255.255.255/cisconet.cfg (Timed out)
    %Error opening tftp://255.255.255.255/nx-5760-wlc01-confg (Timed out)
    %Error opening tftp://255.255.255.255/nx-5760-.cfg (Timed out)
    %Error opening tftp://255.255.255.255/network-confg (Timed out)
    %Error opening tftp://255.255.255.255/cisconet.cfg (Timed out)
    %Error opening tftp://255.255.255.255/nx-5760-wlc01-confg (Timed out)

    I have same problem when i upgraded Cisco 3850 Switch to latest IOS. I have lost access to the console.
    can someone please help.
    Thanks

  • Premiere Pro CC 5 支援 Blackmagic Design Control Panel.

    我在去年試用2014 Premiere Pro CC時.可以使用我之前安裝的Blackmagic Design Control Panel. 但今年初向Adobe 購買2014 Premiere Pro CC使用時.卻發現編輯無法使用Blackmagic Design Control Panel來預覽畫面.此問題一直困擾著我.

    Hi Piero,
    Here's a few ideas you can try.
    1. Place your Blackmagic card in slot 2
    2. Set your OS system sound to Built-in or Line out audio
    3. Set your buffer size to 1024
    4. If those settings fail to help you can place the 9.7.3 plugins into the CC folder. Here's how:
    Mac:
    Copy from:
    /Library/Application Support/Adobe/Common/Plug-ins/CS6/MediaCore
    Paste to:
    /Library/Application Support/Adobe/Common/Plug-ins/7.0/MediaCore
    Hope that is helpful. Let us know how it goes.
    Peter Garaway
    Adobe
    Premiere Pro

  • Embeddable Crystal Reports Designer Control and Visual FoxPro

    Post Author: PaulBtci
    CA Forum: Other
    Hello everyone, I have a problem adding CRXI Embeddable Crystal Reports Designer Control in the run-time. When the following line is being executed, an "Insert Object" dialog pops up. ThisForm.AddObject( "oleDesigner", "olecontrol", "CrystalReports.EmbeddableCrystalReportsDesignerCtrl" ) The control, however, is available in the list, and when selected is added to the form. The above problem does not exist when I add ActiveX ReportViewer. Can anyone help me with this issue? Any help is greatly appreciated. Thanks, Paul

    Good morning,
    I am using  "Embeddable Crystal Reports Designer Control"  Crystal Report 11 with Visual Basic 6.0.
    There is some way for disable the tab "preview the main report"? THis is including in "Embeddable Crystal Reports Designer Control"
    or
    There is some way for update the tab "preview the main report" loaded after other report? Because, the preview is not refresh.
    Thanks
    Buenos días,
    Les comento, estoy utilizando el control "Embeddable Crystal Reports Designer Control" (CRDesignerCtrl11_5) del Crystal Report 11 en un proyecto de Visual Basic 6.0
    Cuando cargo un reporte dos veces, se presenta la "vista previa de informe principal".  Sin embargo cuando vuelvo a cargar otro reporte no se actualiza la "vista previa de informe principal" sino que se queda con la información cargada anteriormente.
    Quisiera saber si existe una forma de acceder al control para actualizar la "vista previa de informe principal", ya que a pesar de dar clic derecho y elegir actualizar no toma los datos del nuevo reporte cargado.
    Y si es posible en todo caso desabilitar la "vista previa de informe principal" o hacerlo invisible para que únicamente se presente la pestaña de "Informe Principal".
    De antemano agradezco su ayuda.

  • Designer Control Problem

    Hey Guys
    I am having a problem and hope you can help to fix it up
    Here is the code i use to open a new Report Using RDC XI with VB6
    Set m_Report = Nothing
    Set m_Report = m_Application.NewReport
    CRDesignerCtrl1.ReportObject = m_Report
    The Above Statements work fine when New Report is created for the first time.
    The Problem is at run time, when i create another new Report (Using Statements above mentioned) Designer Control automaticaly opens its Preview Window tab "Main Report Preview", which was hidden earlier
    As I am using My own Viewrer Control, I don't want this Tab to be opened. I have searched a lot but yet to find any help
    Kindly let me know what can i do TO NOT LET IT OPEN
    Your Cooperation will be very much appreciated!

    Hi Abdul,
    Please don't post multiple times it's the exact same questions as : Designer Control automaticaly opens its Preview Window
    Thanks
    Don

  • Designer Control automaticaly opens its Preview Window

    Hey Guys
    I am having a problem and hope you can help to fix it up
    Here is the code i use to open a new Report Using RDC XI with VB6
    Set m_Report = Nothing
    Set m_Report = m_Application.NewReport
    CRDesignerCtrl1.ReportObject = m_Report
    The Above Statements work fine when New Report is created for the first time.
    The Problem is at run time, when i create another new Report (Using Statements above mentioned) Designer Control automaticaly opens its Preview Window tab "Main Report Preview".
    As I am using My own Viewrer Control, I don't want this Tab to be opened. I have searched a lot but yet to find any help
    Kindly let me know what can i do TO NOT LET IT OPEN
    Your Cooperation will be very much appreciated!

    Thank Ludek for your responce..
    Let me explain code
    Referecnes Added:
    Crystal Reports Active X Designer Design And Run-Time Library 11.5
    Embedable Crystal report Designer Control libaray 11.5
    Crystal Active X Report viewere Library 11.5
    Code
    Dim m_Application As New CRAXDDRT.Application
    Dim m_Report As CRAXDDRT.Report
    ' Code Executed for new Report Button
    Set m_Report = Nothing
    Set m_Report = m_Application.NewReport
    CRDesignerCtrl1.ReportObject = m_Report
    '  Set the report source.
    CRViewer1.ReportSource = m_Report
    '  Set the viewer to view the report.
    CRViewer1.ViewReport
    CRViewer1.Zoom 1
    When this code is executed for the 1st time (If i click New Report Button) It works fine. but if I click New Report button again  "Main Report Preview" tab of Embedable Designer Controls opens automatically. This tab is opened precisely for execution of this statement
    CRDesignerCtrl1.ReportObject = m_Report
    More to add, if i click New Report Button again, it raises error "Index out of range".
    If hope this explain my situation, if there is anything else, let me know.
    Your help will very much be appreciated!
    Abdul Rehman

  • How can I use Embeddable Report Designer Control

    Hi, I found that there is an Embeddable Report Designer Control (CRAXDDRT) which end user could open and edit report runtime (rpt file)
    would you please help me use this control in c#.net
    I have Crystal report 2008
    thank you

    You can not use that in .NET and also there is no craxddrt in CR 2008 as there is no COM SDK for CR 2008.
    Currently there is no .NET equivalent to that dll.
    Jason

  • Embeddable Report Designer Control with Windows 7

    I have a couple of questions.
    I am using Crystal Report XI in both Vb6 and VS2005. I am using the COM controls in both. The CRViewer and the Embeddable Report Designer Control. This has been working in XP fine. Not so good in Vista or Windows 7. I am upgrading to Crystal Reports XI R2 Sp6. For viewing reports in VB6 and VS2005 this working fine.
    I know that the Embeddable designer no longer exists in future Crystal Report versions or in the .net versions.
    In VS2005 the Embeddable Report Designer Control does not work in windows 7.
    Is there anything new that needs to be in the code then in the previous versions? What do I need to do to make the Embeddable Report Designer Control work with windows 7 correctly?
    Also I will need the merge modules for Crystal Reports XI R2 Sp6 for both the .net and RDC. Are they avalible?
    I need to be able to modify reports within the application. My clients have to be able modify existing reports to match state and federal laws and rules.

    Crystal Reports XI R2 Sp6 supports WIN 7, so it should work, though as far as I am concerned, the Embeddable Report Designer Control was always flaky. Also, it may be possible (perhaps even likely) that the RDC components were not tested by QA on WIN 7.
    What is the actual issue you are seeing? (errors, behavior, etc.)
    Are you seeing the issue on a development computer or after you deploy the runtime? I am assuming this is your dev box as you are asking about CR XI SP6 msm files, but I have to be sure.
    If at all possible, do not use the RDC in .NET. The RDC was never tested in .NET and thus is not supported. It may work, but using the Embeddable Report Designer Control in .NET gives me the creeps...
    See if you can get this to work in VB 6 first. If not, you at least have an escalation path for a fix. You do not have an escalation path with RDC in .NET. Please note that if a fix is accepted by R&D, the usual time frame for release of a fix is 6+ months.
    For the future, you will have to look into using the RAS report creation APIs in .NET. This will give you similar report creation abilities at runtime as the Embeddable Report Designer.
    Ludek

  • Embeddable Designer Control

    Post Author: fmenditto
    CA Forum: General
    Is possible to know at runtime wich field have focus in Embeddable Crystal Reports Designer Control ?
    thanks a lot
    Filippo

    Hi Marcus,
    The Embedded Designer Control has always been available but under license only. I believe you have the option to purchase mass keycodes for distribution with your product or you could simply distribute your app runtime only and the end user then purchases a develoepr version of CR to get the runtime files. This covers the licensing for you. If you distribute the runtime you can download the Merge Modules and build a distribution package, check forums, lots of posting on distribution questions.
    Check the License file on the CD/DVD. It explains how each version is licensed.
    There is no replacement for Embeddable Designer control as of CR 2008. Using RAS it has RCAPI functionality and you bascially build your own report designer using the Add methods in within RAS. Typically it is easier to use a template report and make changes as required but it can create a new report without using a template report.
    The other option you have is there is a Java based designer called Eclipse. You can download it and get more info from this link: https://www.sdn.sap.com/irj/boc/crystalreports-java
    It has a designer built in also but you need to be an OEM Partner to be able to distribute it.
    As for migrating there is no one to one API mapping, there is a white paper somewhere that does have info on how to, but with the changes we are still trying to find it. The order of functions are basically the same but the syntax is completely different. You can download sample app's off this site also as well as the developer help file.
    Thats about your only options.
    Thanks again
    Don

  • Design control and simulation palette

    After hitting Next bottoms and succesfully installation for Design control and simulation toolkit , when I launchำก Labview programme  there is nothing in this function and the palette is blank. Anyone knows what happen.  I use Labview 2013 student edition 64 bit(free 6 months version). Thanks in advance+++
    Solved!
    Go to Solution.

    Do you truely have the 64bit version of LabVIEw installed?
    If you do, then you will not be able to use this module.
    It is only valid for 32bit LabVIEW.
    You can see the system requirements here:
    http://www.ni.com/labview/requirements/#cds
    You can try to install 32bit version of LabVIEW and then install the module.

  • How to Retrieve Embeddable Designer Control Selected Report Objects

    How can I Retrieve Selected IReportObject in Embedded Designer?
    Such:
    Dim ro as IReportObject
    set ro = CRDesignerCtrl1.SelectedObjects(1)
    PLEASE HELP

    You will need to get a RCAPI license. These are for OEM Partners only though.
    I suggest rather than using the Embeddable Designer Control to create your own Designer using RAS ( Report Application Server ). It does mean you'll have to create it from the beginning, there is no starting point.
    The reason why I suggest this is as of CR 2008 the RDC is no longer supported nor distributed. Craxddrt.dll is distrubted but only for using within the .NET IDE itself. It is NOT licensed to be used in and application or for distribution.
    What you should try is the Eclypse Java application which you can get from our download page. It is free and comes with a designer control you may be able to use in an application. It does mean you'll have to learn/program in Java.
    If you are interested go to this link: http://www.sdn.sap.com/irj/boc
    And on the left you'll see a link to Crystal Reports for Eclipse. All you have to do is fill in the info and then download it. For more info I suggest you browse the Java SDK forum.
    Thank you
    Don

  • Legal: Reuse RDL Object Model from decompiled Microsoft.ReportingServices.Designer.Controls.dll

    Hi,
    We need to create complex RDLs from code, from scratch and be able to modify existing one.
    The ideal solution is to use RDL Object Model classes from the Microsoft.ReportingServices.Designer.Controls.dll that ships with SSRS 2012.
    Unfortunately that dll is only for x86 and requires lots of depdendencies.
    One of our devs, decompiled that dll and extracted only RDL OM classes, packed into new DLL and made it Any CPU-enabled.
    I do not allowed this approach and wanted to find out first - is it legal doing this? The dll is going to be installed on our IIS-boxes.
    The RDL standard is open so theoretically, re-using plain RDL-OM classes should be legal.
    Thanks,
    Alex

    Hi Alex,
    It’s illegal if you want to reuse RDL Object Model through decompiling Microsoft.ReportingServices.Designer.Controls.dll.
    Regards,
    Heidi Duan
    If you have any feedback on our support, please click
    here.
    Heidi Duan
    TechNet Community Support

  • WLC 5508 and 5760 Compatibility

    Hi, 
    We have 5508 WLC and adding a new 5760..
    is it possible for this 2 to be in the N+1 model?
    If the 5508 WLC goest down, does the AP previously associated to 5508 need to re-download the image to join 5760?
    Or as long as it's running within the following compatibility matrix, The AP wouldn't need to re-download?
    Table 4 Software Compatibility Matrix
    Cisco 5700 WLC
    Catalyst 3850
    Catalyst 3650
    Cisco 5508 WLC or WiSM2
    MSE
    ISE
    ACS
    Cisco PI
    03.03.01SE
    03.03.01SE
    03.03.01SE
    7.6
    7.5
    7.5
    1.2
    5.2, 5.3
    2.0
    03.03.00SE
    03.03.00SE
    03.03.00SE
    7.6
    7.5
    7.5
    1.2
    5.2, 5.3
    2.0
    Thanks for all the answers

    Yes, you can put them in same mobility group.
    To do this you have to enable "New Mobility" feature of your 5508 & configure the mobility between each others.
    Since 7.5.x is deffered only 7.6.x is the option for this. (7.4.x is not supporting this feature). This will enable CAPWAP inter-controller communication instead of EoIP (used by legacy controllers 5508,2504, WiSM)
    HTH
    Rasika
    **** Pls rate all useful responses ****

  • Migrating from Cisco 4402 to 5508 - AP Compatibility

    We currently run six 4402 Wireless lan controllers - these are managed by a WCS server - soon to be replaced by Cisco Prime.
    We run a mixture of LAP1242 and LAP1142 wireless access points.
    I need to add more but have been told by my supplier that the both these AP's are now end of sale and cannot be purchased.
    The replacement AP's are the 2600 series - but I have been told that these are not compatible with my existing 4402 controllers.
    To make matters worse I was then advised that if I purchase the new 5580 controllers the older LAP1242 access points will not work with it and require replacing - this, for me, is a lot of access points.
    What I need to know is:
    What access points, if any, are currently available that are compatible with my 4402 controllers and a future 5508 installation?
    I ssem to be in a situation now where I cannot buy any access points that will work with my 4402's but if I upgrade all my current 1242's will not funtion with the new 5508 controller!
    Scott

    Please look at the compatibility matrix of WLC release and AP's support (it is base on Controller software release)
    Software Support for Access Points
    Access Points
    First Support
    Last Support
    1000 Series
    AIR-AP1010
    3.0.100.0
    4.2.209.0
    AIR-AP1020
    3.0.100.0
    4.2.209.0
    AIR-AP1030
    3.0.100.0
    4.2.209.0
    Airespace AS1200
    4.0
    AIR-LAP1041N
    7.0.98.0
    AIR-LAP1042N
    7.0.98.0
    1100 Series
    AIR-LAP1121
    4.0.155.0
    7.0.x
    1130 Series
    AIR-LAP1131
    3.1.59.24
    1140 Series
    AIR-LAP1141N
    5.2.157.0
    AIR-LAP1142N
    5.2.157.0
    1220 Series
    AIR-AP1220A
    3.1.59.24
    7.0.x
    AIR-AP1220B
    3.1.59.24
    7.0.x
    1230 Series
    AIR-AP1230A
    3.1.59.24
    7.0.x
    AIR-AP1230B
    3.1.59.24
    7.0.x
    AIR-LAP1231G
    3.1.59.24
    7.0.x
    AIR-LAP1232AG
    3.1.59.24
    7.0.x
    1240 Series
    AIR-LAP1242G
    3.1.59.24
    AIR-LAP1242AG
    3.1.59.24
    1250 Series
    AIR-LAP1250
    4.2.61.0
    AIR-LAP1252G
    4.2.61.0
    AIR-LAP1252AG
    4.2.61.0
    1260 Series
    AIR-LAP1261N
    7.0.116.0
    AIR-LAP1262N
    7.0.98.0
    1300 Series
    AIR-BR1310G
    4.0.155.0
    7.0.x
    1400 Series
    Standalone Only
    1600 Series
    AIR-CAP1602I-x-K9
    7.4.100.0
    AIR-CAP1602I-xK910
    7.4.100.0
    AIR-SAP1602I-x-K9
    7.4.100.0
    AIR-SAP1602I-xK9-5
    7.4.100.0
    AIR-CAP1602E-x-K9
    7.4.100.0
    AIR-SAP1602E-xK9-5
    7.4.100.0
    AP801
    ap801-k9w7-tar
    5.1.151.0
    2600 Series
    AIR-CAP2602I-x-K9
    7.2.110.0
    AIR-CAP2602I-xK910
    7.2.110.0
    AIR-SAP2602I-x-K9
    7.2.110.0
    AIR-SAP2602I-x-K95
    7.2.110.0
    AIR-CAP2602E-x-K9
    7.2.110.0
    AIR-CAP2602E-xK910
    7.2.110.0
    AIR-SAP2602E-x-K9
    7.2.110.0
    AIR-SAP2602E-x-K95
    7.2.110.0
    3500 Series
    AIR-CAP3501E
    7.0.98.0
    AIR-CAP3501I
    7.0.98.0
    AIR-CAP3502E
    7.0.98.0
    AIR-CAP3502I
    7.0.98.0
    AIR-CAP3502P
    7.0.116.0
    3600 Series
    AIR-CAP3602I-x-K9
    7.1.91.0
    AIR-CAP3602I-xK910
    7.1.91.0
    AIR-CAP3602E-x-K9
    7.1.91.0
    AIR-CAP3602E-xK910
    7.1.91.0
    600 Series
    AIR-OEAP602I
    7.0.116.0
    Note The Cisco 3600 Access Point was introduced in 7.1.91.0. If your network deployment uses Cisco 3600 Access Points with release 7.1.91.0, we highly recommend that you upgrade to 7.2.103.0 or a later release.
    1500 Mesh Series
    AIR-LAP-1505
    3.1.59.24
    4.2.207.54M
    AIR-LAP-1510
    3.1.59.24
    4.2.207.54M
    1520 Mesh Series
    AIR-LAP1522AG
    -A and N: 4.1.190.1 or 5.2 or later1
    All other reg. domains: 4.1.191.24M or 5.2 or later1
    AIR-LAP1522HZ
    -A and N: 4.1.190.1 or 5.2 or later1
    All other reg. domains: 4.1.191.24M or 5.2 or later1
    AIR-LAP1522PC
    -A and N: 4.1.190.1 or 5.2 or later1
    All other reg. domains: 4.1.191.24M or 5.2 or later1
    AIR-LAP1522CM
    7.0.116.0 or later.
    AIR-LAP1524SB
    -A, C and N: 6.0 or later
    All other reg. domains: 7.0.116.0 or later.
    AIR-LAP1524PS
    -A: 4.1.192.22M or 5.2 or later1
    1550
    AIR-CAP1552I-x-K9
    7.0.116.0
    AIR-CAP1552E-x-K9
    7.0.116.0
    AIR-CAP1552C-x-K9
    7.0.116.0
    AIR-CAP1552H-x-K9
    7.0.116.0
    AIR-CAP1552CU-x-K9
    7.3.101.0
    AIR-CAP1552EU-x-K9
    7.3.101.0
    1552S
    AIR-CAP1552SA-x-K9
    7.0.220.0
    AIR-CAP1552SD-x-K9
    7.0.220.0

Maybe you are looking for