Desk jet DJ4515 setup via mobile

I have purchased a desk jet dj4515 and wanted to know if I can install and set the printer up using a mobile phone as I do not have a laptop or computer.

Dear Lewington,
Here you have some documents where explains how to print from a mobile:
http://support.hp.com/in-en/product/HP-Deskjet-Ink-Advantage-4510-e-All-in-One-Printer-series/528599...
http://support.hp.com/in-en/product/HP-Deskjet-Ink-Advantage-4510-e-All-in-One-Printer-series/528599...
http://support.hp.com/in-en/product/HP-Deskjet-Ink-Advantage-4510-e-All-in-One-Printer-series/528599...
I hope you find it helpful.
Greetings.
* I am not an employee of HP, my work is voluntary.
If this answer was helpful and clarify or resolve your problem, please mark the issue as resolved and click my star next to give a kudo as thanks.
I am not an employee of HP, my work is voluntary. If this answer has been helpful and clarifies or solves your problem, please click the button
and click on the icon if you want acknowledge the assistance.

Similar Messages

  • Connecting iPad to desk jet 2540 printer

    How can I connect my new hp desk jet 2540 printer to my iPad as the web page dose not work and there dose not seem to be any other way as an iPad dose not have a cd rom.

    Hi,
    If your router support WPS (Wireless Protected Setup), you may connect it to your network using this method, you may find the steps below:
    Method one: Push buttonFollow these instructions to connect using the Push button method on your printer control panel.
    On the printer control panel, press and hold the Wireless button ( ) for more than three seconds. The Wireless Status light starts blinking.
    Press the WPS button on your router. The printer begins a timer for approximately two minutes while a wireless connection is established.
    Method two: PINFollow these instructions to connect using the PIN method on your printer control panel.
    On the printer's control panel, press the Wireless button ( ) and the Start Copy Black button ( ) at the same time. The Network Configuration page prints.
    Find the WPS PIN printed at the top of the page.
    On the printer control panel, press and hold the Wireless button ( ) for more than three seconds. The Wireless Status light starts blinking.
    Open the configuration utility or software for the wireless router or wireless access point, and then enter the WPS PIN.
    NOTE: For more information about using the configuration utility, see the documentation provided with the router or wireless access point.
    Wait about 2 minutes. If the printer connects successfully, the wireless light stops blinking but remains lit.
    If your router does not support WPS, a computer is required for its network configuration. use any Windows PC or a Mac to connect it for the first time by following these steps:
    http://h10025.www1.hp.com/ewfrf/wc/document?docname=c03820126&tmp_task=useCategory&cc=us&dlc=en&lc=e...
    Regards,
    Shlomi
    Say thanks by clicking the Kudos thumb up in the post.
    If my post resolve your problem please mark it as an Accepted Solution

  • I have an iPad and desk jet 3520e how do I set this up, do I need a computer to set it up?

    I have an iPad and recently bought desk jet 3520e, do I need a computer to set this up? I am no technical genius so any help in how to go about it would be really helpful.

    Hi,
    Based on teh following specs:
      http://h10010.www1.hp.com/wwpc/us/en/sm/WF06a/18972-18972-238444-1142650-410635-5162504.html?dnr=1
    it supports ePrint & AirPrint. For iPad please use the following setup:
        http://www.apple.com/support/ipad/assistant/airprint/
    You can also use the followung setup:
        http://itunes.apple.com/au/app/hp-eprint/id299531647?mt=8
    Regards.
    BH
    **Click the KUDOS thumb up on the left to say 'Thanks'**
    Make it easier for other people to find solutions by marking a Reply 'Accept as Solution' if it solves your problem.

  • I have a Desk Jet 3050. How can I get it back online?

    The product is HP Desk Jet 3050 , I operate on Windows 7. Printer is saying not connected to wireless. My local cable company had internet issues and the printer worked fine before. Everything BUT the wireless printer worked normal after the issue was repaired by cable company. I have tried the HP scan doctor download. It comes back as saying the printer has no power. Which it clearly does. I have powered everything off then repowered. Nothing happened. The test report states Network Name::FAIL. I do not know how to fix this problem. Any suggestion will be helpful!
    This question was solved.
    View Solution.

    On the front of the printer, go to the Wireless menu and Restore Defaults.
    Go to Start > Control Panel > Devices and printers and delete all instances of the printer.
    Now, go to Start > All Programs > HP > [your printer model] > Printer Setup and Software.
    Say thanks by clicking "Kudos" "thumbs up" in the post that helped you.
    I am employed by HP

  • How do I set up wireless printing between my desk jet 2542 and my computer?

    how do I set up wireless printing between my desk jet 2542 and my computer?

    Hello danamaple,
    Welcome to the HP Support Forums!
    Depending on the Operating System installed on the computer, setting up the Deskjet 2540 can be done different ways. The easiest and most popular method is to use a USB cable and the printer software to setup wireless on the printer.
    Installing the Printer Software for a Wireless Network Connection<---
    This guide should provide the needed information for you to setup the printer on the network. Please let me know if you have anymore questions.
    JERENDS
    I work on behalf of HP
    Please click “Accept as Solution” if you feel my post solved your issue, it will help others find the solution.
    Click the “Kudos Thumbs Up" to the left of the reply button to say “Thanks” for helping!

  • Macbook pro recognizes but won't print with hp desk jet 5550. Help!

    macbook pro recognizes but won't print with hp desk jet 5550. Help!

    Hi, I used the Mac setup instructions, not the PC ones.  The printer was automatically recognised in print and scan when I connected it with a USB cable.  I accessed the server's web-based page and followed all the instructions, but still no joy.  Thanks for the tip about posting.  I have just posted in the section you suggested, so let's see what happens.  From a quick scan around the apple forums, lost of other people seem to having precisely the same problem (and not just with HP printers!), but unfortunately, no-one seems to be offering a solution!  And trying to get through to the apple online support is a complete waste of time.  They've been 'not available' for two days now.  Christmas/New Year shutdown, I suppose.  Thanks for all your help, though!

  • Reverse Proxy setup for Mobility HTTP 80 configuration not working

    http://technet.microsoft.com/en-us/library/hh690011(v=ocs.14).aspx
    I'm trying to use the Port 80 ->8080 setup to avoid putting lyncdiscover.sipdomain.com for every additional sip domain that we want to include.
    I have followed the instructions per the above link, yet when I try to log in with a user with one of those additional SIP's, I cannot log in to a mobile device.
    For example,
    our main sip is "contoso.com", so
    [email protected] can log into her mobile device.
    but user [email protected] cannot log in via mobile device.
    Is there anything else that needs to be done to ensure that
    [email protected] can login via a mobile device?
    Auto login?
    Josh
    Here is the testexchangeconnectivity.com
    When I run the Lync Mobile Test, I get this, almost like the http rule is useless, still requiring the need for the additional lyncdiscover.sipdomain.com .
    [email protected]
    Testing connectivity to the Lync Autodiscover Web Service server for a secure connection on port 443 to obtain the root token.
      Connectivity to the Lync Autodiscover Web Service test failed.
     Test Steps
     Attempting to test Autodiscover Web Service URL https://lyncdiscover.fabrikam.com/Autodiscover/AutodiscoverService.svc/root.
      Autodiscover Web Service URL can't be contacted due to failure of the following tests:
     Test Steps
     Attempting to resolve the host name lyncdiscover.fabrikam.com in DNS.
      The host name resolved successfully.
     Additional Details
     Testing TCP port 443 on host lyncdiscover.fabrikam.com to ensure it's listening and open.
      The port was opened successfully.
     Testing the SSL certificate to make sure it's valid.
      The SSL certificate failed one or more certificate validation checks.
     Test Steps
     ExRCA is attempting to obtain the SSL certificate from remote server lyncdiscover.fabrikam.com on port 443.
      ExRCA successfully obtained the remote SSL certificate.
     Additional Details
     Validating the certificate name.
      Certificate name validation failed.
       Tell me more about this issue and how to resolve it
     Additional Details
      Host name lyncdiscover.fabrikam.com doesn't match any name found on the server certificate CN=lncpool01.contoso.com, OU=Domain Control Validated.

    Hi,
    Please verify DNS record for Lyncdiscover.fabrikam.com can be resolved.
    Please make sure the web publishing rule for port 80 has been configured correcltly. The lyncdiscover.<sipdomain> entry must to be included in rule. Verify that port 8080 was typed in "Redirect requests to HTTP port" and Redirect
    requests to SSL port is not selected.
    Kent Huang
    TechNet Community Support

  • 500GB TM - sharing external disc via mobile me

    Hi i wonder how to share external disc via mobile me, I connected it and shared in my network, then used airport utility to share it via mobile me but it just didnt show up.
    where can i find it on the mobile me account? thanks

    well i used mobile me account in setup but it just doesnt apper in finder

  • Time Capsule remote access via mobile me

    Hi there,
    i heard it would be possible to connect to my time capsule even if i am not in my network (at home, in other cities etc) via mobile me service, has anybody experience with this?
    I am using mobile me in the trial/test version. Are there more options in the full version?
    I need to share data with colleagues in other cities but couldn't find a way to do this so far.
    First I tried out a ready nas duo from netgear, a terrible desaster i would not consider to anybody.
    Does apple offer any solution without spending more than 500 euro?

    This is what I know(and it works) so far.
    Using Mobile Me, you must have a Mac to access your TC remotely.
    Also, I had to get static IP address(on TC side) to get this to work. I was having trouble using the dynamic address assigned by my ISP. If you get an error message regarding double NAT, chances are you'll need to get a static IP address like I did.
    If you get an error message regarding NAT Port Mapping Protocol or UPnP, see 1a. below.
    1. On TC, in manual setup, enter your MM username and password in Back to my Mac.
    1a. Make sure that you enable NAT Port Mapping Protocol.
    2. On your mac, enter your MM username and passeord.
    2a. Also, enable Back to my Mac.
    2b. Keep an eye out for any error messages.
    I hope it helps.

  • Can a user take part in video conference via mobiles e.g. smart phone, etc?

    Hello Community
        Using Lync Server can a user start or take part in a Lync Server video conference 
    via mobile devices like their smart phones, etc just as if they were sitting at their desks
    taking part in the Video Conference?
        Thank you

    Hi Shabeaut
    You can use Lync 2013 mobile clients which  provide enhanced presence, IM, Lync meetings, and voice
    and video calls over the Internet .
    Check under category "Conferencing Support in Lync Mobile clients" to get all capabilities and features available for
    Lync client
    https://technet.microsoft.com/en-us/library/hh691004.aspx
    Please mark it as answer if it helps you solving your problem.
    Amit Kotha

  • I cannot detect my wireless hp desk jet 3520 printer, I cannot detect my wireless hp desk jet 3520 printer

    I cannot detect my wireless HP desk jet 3520 printer from my iPad? 

    I can't find an Arris router with that model number, are you sure it is not a TG862?
    Regardless, Arris routers are known to either be incompatible with Bonjour or have problems with Bonjour packets hence Airprint will not work. Check with Arris' website and see if there is a firmware update availble for your router for Bonjour/Airprint compatibility and install it or switch out your router.

  • Hi i would like to know how to extend the range of my time capsule wifi network(500G 802.11n) using an airport express. i have a double storey home and would like to extend range to my upstairs bedrooms.i have a time capsules network setup via a netgear a

    hi i would like to know how to extend the range of my time capsule wifi network(500G 802.11n) using an airport express. i have a double storey home and would like to extend range to my upstairs bedrooms.i have a time capsules network setup via a netgear adsl.i have a second imac upstairs which connects to time capsule wifi network (it is within range as it is directly abobe on 1st floor)
    could you tell me how best to set airport express up to extend my wifi range?

    Greetings,
    This is called an "Extended wireless network".
    Read this article for details and steps on how to extend your TimeCapsule's network:
    http://support.apple.com/kb/HT4259
    Cheers.

  • Help with HP desk jet F4435 on MacBookPro

    I tried installing my HP desk jet F4435 with the disc that came with the printer. I received a "successful" message. It wouldn't print. Then I uninstalled the printer and tried just plugging in the USB to connect it. Tried printing and receieved yet another error message.
    HELP!

    Some hp driver software for your printer here:
    http://h10025.www1.hp.com/ewfrf/wc/softwareCategory?os=219&lc=en&cc=us&dlc=&sw_l ang=&product=304431#N207
    If needed, gutenprint 5.2.9 can be obtained here:
    http://gimp-print.sourceforge.net/MacOSX.php
    Many network printers do not require an explicit driver, or can use "Generic". They accept standard protocols and can be printed to directly. If the printer can be discovered automatically and appears in the list of available printers, it should determine what driver is needed and go fetch any needed driver for you.

  • How do I get facebook app to say a status via ipad instead of via mobile?, How do I get facebook app to say a status via ipad instead of via mobile?

    When I upload a status with facebook on my ipad it says via mobile and not ipad. Do I need 3G or able to do it connected to wi-fi

    Someone please help , is it because it is not an ipad app? Yet I remember when iPads where first out in the apple store uploading a status in store iPads said is ipad

  • Can not open pdf after saving scan from desk jet 3050

    I can open pdf file sent to me but I can not open scanned pdf files I scanned with my desk jet 3050 J610

    Hi Marymae07,
    Welcome to the HP Support Forums! I see you are not able to open up a saved pdf file once you save the scan with your HP Deskjet 3050.  To better assist you, can you please leave me with the following information:
    1. What is your current Operating system, Windows or Mac and which version?
    2. What program are you using to scan, are you using the HP software or another program?
    3. Do you get any error messages when you attempt to save as pdf file?
    4. Are you able to save the scan in another format like jpeg?
    I will watch for your reply, so we can begin troubleshooting.
    Thanks,
    HevnLgh
    I work on behalf of HP
    Please click “Accept as Solution” if you feel my post solved your issue, it will help others find the solution.
    Click the “Kudos Thumbs Up" to the left of the reply button to say “Thanks” for helping!

Maybe you are looking for