Desperate help needed to configure WVC210 for remote access?

Hi, I'm new and desperately need some help on setting up my WVC210 for remote access.
I manage to setup and see images from my WVC210 using my home LAN via both wired and also wireless.
I have 2 questions:
(a) for wireless connection, i only manage to get connection to my WVC210 if i disable the wireless security from my router. But that means i'm opening my wireless LAN to everyone. How can i still get connection to the camera if i enable the wireless security from my router. (FYI: my router is 2Wire ADSL  from Singnet Mio)
(b) how can i get connection to my WVC210 from outside or in my office? I type in the camera Fixed IP address (displayed on the front screen) on the web browser, by it shows a error page. Is there some setting that i might need to adjust ?
Pls kindly help me
Thank you.

Bernard,
For Item (2) is there any difference between the camera built-in dyndns updater versus the software updater? I am under the impression that the software updater is easier to manage.
The biggest difference for you is that the camera always stays at the same location, and the laptop goes with you. Every time you access the internet from a different location with the laptop the software updater is sending the new IP address to dyndns.com. This causes you to lose access to your camera because the FQDN doesn't point to your home IP address anymore. Once the dyndns credentials are in the camera (or router) there is no management needed. The device will automatically update dyndns.com with your new IP address as it changes, and you do not need to do anything.
For Item (3), are you saying port forward 1025 is it for the 2nd camera only or for both? Or is it 2nd camera use 1025 and first camera use 8080?
Here's an example of what I mean:
Camera 1: 192.168.1.210 port 1024. In router, forward port 1024 to 192.168.1.210
Local Access: http://192.168.1.210:1024
Remote Access: http://bernards210.dyndns.org:1024 (Example)
Camera 2: 192.168.1.211 port 1025. In router, forward port 1025 to 192.168.1.211
Local Access: http://192.168.1.211:1025
Remote Access: http://bernards210.dyndns.org:1025 (Example)
Camera 3: 192.168.1.212 port 1026. In router, forward port 1026 to 192.168.1.212
Local Access: http://192.168.1.212:1026
Remote Access: http://bernards210.dyndns.org:1026 (Example)
to access the 2 camera outside, do i have to have another dyndns host name or can i use the current one for both camera?
As you can see in the above example, the dyndns name remains the same for remote access to all three cameras. The only change is the port number at the end. Your router will translate the port number to the IP address that the port is forwarded to, allowing you to select the camera that you wish to view by changing the port number in the address.
I was actually thinking that the camera web browser can show 2 camera at the same time. Is it possible?
No. Each browser window will display a single camera. You can however opens multiple instances of your browser to allow viewing of more than one camera simultaneously. A better solution is to install the Video Monitoring Software that is included with the camera which allows you to view multiple cameras in the same window.

Similar Messages

  • Help setting up Lion Server for remote access

    I have been going in cricles for weeks trying to set this up correctly.  Can anyone tell me what I'm doing wrong?
    I got Lion Server and Server Admin Tools all updated and have been trying to follow Terry Walsh from We Got Served's guide but I missing something.
    I purchased a domain from GoDaddy. Let's call it bradnet.com
    My domain and dyn domain are not really what I have typed here but close enought that they should work for my example and trouble shooting.
    Because my ISP (Comcast) doesn't provide a static IP I registerd for an account with dyn.com.  This is where I get really confused.  With dyn.com i created a host name: bradnet.dyndns-rocks.com and downloaded there updater software.  It found my public IP address and said everything is ok.
    I went back to GoDaddy and in my DNS manger page added the host: bradnet.dyndns-rocks.com and entered my public IP.
    I then went to the server pane to edit the host name.  I followed your instructions to edit the name and selected Host Name for Internet.  I left the computer name as mini (what I had previously named it for file sharing before the server upgrade) and entered  mini.bradnet.dyndns-rocks.com as the host name.  When it takes me back to the server pane, in the bottom window it states:
    Your Server's host name is mini.bradnet.dyndns-rocks.com, and its IP address is 192.168.1.10. You can change network settings in the Server pane.
    I never get the your network is configured properly message.
    I went and set my computer's IP to DHCP with manual address (although all of my machines are set up with DHCP reservations so I guess that is a little redundant) to 192.168.1.10.
    I skipped the port forwarding step because I am using the latest AirPort Extreme as my router.
    I then opened a browser and tried:
    http://bradnet.com
    http://mini.bradnet.dyndns-rocks.com
    http://mini.bradnet.com
    http://bradnet.dyndns-rocks.com
    All of these got me the can't find the server response from Safari.
    Also, I have not yet set up Directory Services.  Terry's guide seems to suggest to do this step first.
    I'm sure I have messed up some step somewhere can you see what I have done wrong?
    Also, is it a problem to set up open directory services using a .local host and then go back and change it for internet access later or do you need to set that up from the start?  My family is getting impatient with me trying to get this to work.
    Thanks for any help anyone can offer!
    Brad

    That manual page is not fully correct. There is written:
    Public UDP Port(s): <enter the appropriate UDP port value(s)>
    Public TCP Port(s): <enter the appropriate TCP port value(s)>
    Private IP Address: <enter the reserved IP address of the host device (from step 1)>
    Private UDP Port(s): <enter the same Public UDP Ports or your choice>
    Private TCP Port(s): <enter the same Public TCP Ports or your choice>
    But it should be:
    Public UDP Port(s): <enter unique UDP Ports of your choice>
    Public TCP Port(s): <enter unique TCP Ports of your choice>
    Private IP Address: <enter the reserved IP address of the host device (from step 1)>
    Private UDP Port(s): <enter the UDP Ports used by your device>
    Private TCP Port(s): <enter the TCP Ports used by your device>
    Make sure you use the same ports in the private settings as you have defined in your IP camera. Normally a camera will use port 80 by default, so use 80 here.
    The Public ports must all be unique. If you have not defined a port 80 here, you can also use 80. This will fail however when using multiple cameras. I for instance have 5 IP cameras and use the public ports 8451, 8452, 8453 etc.

  • Urgent help needed in configuring X1151A for RAC cluster

    for RAC requirements I have to configure this card to use the interface name of ce1 but I have tried changing slots and puting /etc/hostname.ce1 file out there but it fails .. it always comes up as ce0.
    my question is : How can I cofigure this card to come up as ce1 ? in the other box I had to do nothing .. i just placed the /etc/hostname.ce1 file with hostname and it works perfect.
    can you please email me a copy of your response at [email protected] ?
    thanks
    Sami

    Look for "ce" instances in the /etc/path_to_inst file. You'll need to change the lines so that the hardware path you want is "1".
    Keep a backup and write down the pathname. You can give that path to a 'boot -a' prompt if anything bad happens.
    Darren

  • Configure Time Capsule for remote access

    I have a second generation 2TB Time Capsule, operating on Bridge Mode, connected to an Arris Touchstone Telephony Gateway TG862. I want to configure Back to My Mac to be able to access the Time Capsule remotely.
    I've followed the basic steps and get this message from the settings in the iCloud Pane in System Preferences: Setup router for better performance. And this details: Contact your ISP for a different server address.
    I've tried Google and OpenDNS, and also disabling the Firewall in the Arris router, and still can't access the Time Capsule remotely.
    I also tried disabling NAT and seeing it up as Bridged in the router, and disabling Wireless as well, trying to configure the Time Capsule to serve NAT and DHCP to no avail.
    Any steps I'm missing or a whole different approach I should take to be able to access my Time Capsule remotely?
    Thank you in advance for any help.

    You will have to learn how to port forward in your Arris Gateway..
    Arris Touchstone Telephony Gateway TG862
    The easiest way is to simply google it.
    http://forums.comcast.com/t5/Home-Networking-Router-WiFi/Port-forwarding-in-Arri s-TG852G-CT/td-p/954929
    It certainly appears to be problematic.. which is not surprising... If you really need remote access I would request a pure modem from your ISP (Comcast??) or simply replace it with one in the list. You will need to turn off any inbuilt firewall in the router and use DMZ perhaps to the TC.
    There is a few posts on youtube which also might help you. eg
    https://www.youtube.com/watch?v=_8tKBHvCz_0
    But I am on ADSL so my setup is too unlike yours to really tell you much.
    If you want to test something.. let me recommend you load Teamviewer onto a computer in your LAN.. set the computer up to never sleep and then try and reach it using Teamviewer from WAN connection.. if that works.. let me recommend you stick to something of this type. Unless you are prepared to change modems with your ISP I doubt you will solve it.
    If teamviewer fails nothing is going to work.. you need to at least turn off the firewalls in both the computer and the router..
    If you don't want to leave a computer running 24/7 to accept incoming requests.. then use WD MyCloud or similar type NAS.. which are far better designed for remote access than Apple routers.. or use a cloud storage and keep files you might want there.

  • Remote Desktop Service Manager - configure permissions for Remote Desktop Users to Send Message, Disconnect, Logoff

    Hello, dear colleagues.
    We are using Windows Server 2012 R2 as Remote Desktop Server. Also use Windows Server 2008 R2 with Remote Desktop Service Manager to control RDS user sessions (Send Message, Disconnect, Logoff, Query Info). 
    Send Message, Disconnect, Logoff options works only for users in Administrators group.
    I can't to configure permissions for Remote Desktop Users, specific user or AD group. 
    To set permissions I'm running RDS Host Configuration on Windows Server 2008 R2 and connect to Windows Server 2012 R2. Then double-click
    RDP-Tcp, Security tab, add specific user account , AD group or configure
    advanced permissions
    for Remote Desktop Users.  
    But, as I sad above, these options works only for users in Administrators group. How to make it work for Remote Desktop Users or specific user, AD group?
    Thanks.
    P.S. If move specific user from Remote Desktop Users group to Administrators group on
    Windows Server 2012 R2 - it works. 

    Hi,
    You can prevent administrators from changing the permissions for a connection by applying the
    Do not allow local administrators to customize permissions Group Policy setting. 
    This Group Policy setting is located in Computer Configuration\Policies\Administrative Templates\Windows Components\Remote Desktop Services\Remote Desktop Session Host\Security
    Apart there is one command with which you can set the permission for that check the related
    article. Additionally checkthis
    thread for more detail.
    Hope it helps!
    Thanks.
    Dharmesh Solanki
    Please remember to mark the replies as answers if they help and unmark them if they provide no help. If you have feedback for TechNet Support, contact [email protected]

  • I am trying to use an external HD and need to configure it for the MAC. Can someone explain how to configure the HD (Western Digital - My Passport SE)?

    Can someone help explain how to add an external HD to the Mac? I have a Western Digital My Passport SE and need to configure if for the MAC and add it to the HD location on my Mac.

    Connect the external drive to the Mac. You can do that while the Mac is on, (If the drive is one that has to be plugged into a wall outlet do that too and turn the power on.) If there is a light on the drive it should turn on.
    Now double click on the hard drive icon - top left of the screen of your computer. When it opens look for the Applications folder. Double click that. Next look for a folder called Utilities. Double click. In there you will see a file called Disk Utility.app. Double click on that.
    You will now see something like this, with two items on the left. The second one is your new drive.
    Select it - one click. And click on Erase - one of the buttons at the top, You will see this.
    You must select the Format, it's a drop down - the one shown in the image above is best. You can change the name from Untitled if you want. The name can be changed later if you prefer.
    At this point look at the bottom right. There is a button there called Erase. Click on it. Then go get yourself a cup of coffee - this will take a few minutes.

  • Help need my mac pro for school..it has Grey screen..spinning wheel...repaid disk ok...repair disk permission all repaired but one warning...

    Help need my mac pro for school..it has Grey screen..spinning wheel...
    I think I have  mountain lion OS X....I have done I think almost every suggestion I've seen in discussion boards.
    Boot in recovery repaired disk...ok...repair disk permission...all repaired but one warning...I've tried to reinstall lion (without losing data) and it Got all the way to one minute to be done and then the time change back two hours and kept doing this all night long.  I haven't done a back up due to no external for time machine.
    I hope someone can please help me I've been going crazy for a week now trying to figure this out.  I use my computer for school and I'm currently very behind from in my school work  thank you
    Also I've checked my available space  424.91 free of 750 gigs....disk is verified

    Welcome to the Apple Support Communities
    Try holding the Shift key while your Mac is starting to start into safe mode. Then, after starting in safe mode, open Finder, select Go menu (on the menu bar) > Go to Folder, and type /Library/StartupItems. Then, empty this folder and restart the Mac.
    If your Mac starts after doing this, it was a problem with a third-party app that starts automatically when you turn on the computer. It won't start automatically anymore after doing that

  • LDAP vs local login for remote access

    Hi Team,
    I am evaluating the best means for single factor authentication for remote access (client to site or SSL VPN). The options I see are creating local usernames and password or integration with Active Directory via LDAP. What are the pros and cons of these solutions.
    I feel local logins are more secure comparitavely because the user first login using local login and password and then has to use the domain credentials for accessing corporate resources. Of course, this comes at an admistrator overload and local management of user names and passwords. Do you have any opinion on this? Any acknowledgement will be highly appreciated.

    Hello Manoj,
    IMO, I would never consider the LOCAL DB as an option for a corporate deployment. It does not scale and it is not easy to manage.
    Local DB is used in case you need to manage a number of 15 users for instance, so in this case it is managable, but when it comes to a higher number it is not an option.
    Active Directory is a better solution since it is meant to handle hundred of users and allows password-management for instance. Also you can have many ASA devices, performing DB bindings and queries to check the users credentials to the AD servers, so you don't need to deal with tons of user accounts on each ASA, for instance.
    If you are looking for a more secure way to authenticate your users you can consider two-factor authentication using certificates for instance:
    AnyConnect Certificate Based Authentication.
    Why to use AD:
    Pros
    Scalable.
    Easy to manage.
    Allows password-management.
    Cons:
    Expensive (not open AD solution).
    HTH.
    Please rate helpful posts.

  • How to Use synchronous RFC calls during test run for remote accesses

    there is a Setting for the usage of RFC accesses from a tested system
    using eCATT.
    'X' - Use asynchronous RFC calls during test run for remote accesses
    ' ' - Use synchronous RFC calls during test run for remote accesses
    I developed an eCATT as following :
      SAPGUI ( SAPGUI_1 , Target_system_1 ).
      SAPGUI ( SAPGUI_2 , Target_system_2 ).
    My question is how to run the eCATT in a synchronous RFC calls
    PS: I do not want to change the Target_system to the same one in the
    above script of ecatt.Because I need to run it in 2 different Target
    systems sometime.
    for example, I give a Target_system_3 when run this eCATT
    I want the SAPGUI_1 and SAPGUI_2 run the Target_system_3 but not the
    Target_system_1 or Target_system_2 .
    Could you please tell me how to make it without the changes in script?
    Edited by: Weitong Liu on Mar 24, 2011 9:44 AM

    Hi Liu,
    Weitong Liu wrote:
    > ' ' - Use synchronous RFC calls during test run for remote accesses
    This is the standard option value. Asynchronous are not the standard way and used only for very special purposes.
    Weitong Liu wrote:
    > I developed an eCATT as following :
    >   SAPGUI ( SAPGUI_1 , Target_system_1 ).
    >   SAPGUI ( SAPGUI_2 , Target_system_2 ).
    > My question is how to run the eCATT in a synchronous RFC calls
    The commands will be executed in sequence. So each call will be synchronously replayed against TS1 and TS2.
    What is you issue with this standard procedure?
    Kind regards,
    Christoph

  • Need to configure Airport connection to access corporate wireless network

    Need to configure Airport connection to access corporate wireless network.
    Have imported my certificate from Windows XP machine into keychain and made Leopard always trust in order to authenticate automatically into my corporate wireless network. Also attempted to establish a new 802.1x connection via network preferences without any success. It keeps asking me for username and password even though we used self-generated certificates to log into corporate wireless network. Does anybody have any instructions on how to successfully configure certificates in Leopard?

    Welcome to the discussion area, jackregan!
    You'll need to "hard reset" the Time Capsule and then reconfigure it again. To do this, you will hold in the reset button until you see the amber light begin to blink more quickly, keep holding another second or two and then release.
    The "hard reset" will not affect the data on your Time Capsule
    Now you can open AirPort Utility and configure the Time Capsule using wireless (be sure to log on to the default network which will have a name like Apple Network xxxxxx), or you can connect an ethernet cable from your computer to one of the LAN <-> ports on the Time Capsule to have AirPort Utility communicate with it that way.
    When you open AirPort Utility, click Continue to follow the guided setup to re-configure your Time Capsule. You would choose the option to "Create a wireless network" when you are given the configuration options.

  • VRF-Aware IPSec for Remote Access

    Dear All,
    Has anyone successfully implemented VRF-Aware IPSec for Remote Access ?
    I am trying to implement this feature on a PE which has MPLS enabled
    on the Internet facing interface.
    With the config below, I am being able to establish an IPSEc tunnel but not being able to PING the VRF interface configured on the same PE.
    I will be really grateful for any comment or any pointers for what could
    be possibly wrong with the configuration below:
    aaa new-model
    aaa authentication login USER-AUTHENTICATION local
    aaa authorization network GROUP-AUTHORISATION local
    crypto keyring test-1
    crypto isakmp policy 1
    encr 3des
    authentication pre-share
    group 2
    crypto isakmp client configuration group test-1
    key test-1
    domain test.com
    pool cpe-1
    acl 101
    crypto isakmp profile test-1
    vrf test-1
    keyring test-1
    match identity group test-1
    client authentication list USER-AUTHENTICATION
    isakmp authorization list GROUP-AUTHORISATION
    client configuration address initiate
    client configuration address respond
    client configuration group test-1
    crypto map IPSEC-AWARE-VRF 2 ipsec-isakmp dynamic test-1
    ip local pool cpe-1 192.168.81.1 192.168.81.254 group test-1
    crypto dynamic-map test-1 1
    set transform-set test-1
    set isakmp-profile test-1
    reverse-route remote-peer
    Internet facing interface
    interface GigabitEthernet4/0/0
    ip address x.x.x.x 255.255.255.240
    ip router isis
    mpls ip
    crypto map IPSEC-AWARE-VRF
    Customer facing interface
    interface GigabitEthernet1/0/0.1
    encapsulation dot1Q 100
    ip vrf forwarding test-1
    ip address 110.110.110.1 255.255.255.0
    Kind regards,
    ZH

    Million thanks for this.
    This now works after disabling CEF on the public facing interface.
    Regards,
    Zahid

  • I have a mac mini server which I want to set up for remote access from windows and mac pcs.  How do I do this.  I can access it form my home network OK

    I have a mac mini server which I want to set up for remote access from windows and mac pcs.  How do I do this.  I can access it form my home network OK

    Posted in error.

  • How to enable second HD DVR for remote access?

    I easily got my first HD DVR setup for remote access and it worked perfetly for 1 day, then it stopped working.  After 2 hours on the phone with tech support, we got it to work again.  However, we were unable to get my second DVR setup.  He said that I could only have one DVR setup for remote access, is that true?  If not, any assistance would be much appreciated. 
    Thank you!

    glcockrum wrote:
    I easily got my first HD DVR setup for remote access and it worked perfetly for 1 day, then it stopped working.  After 2 hours on the phone with tech support, we got it to work again.  However, we were unable to get my second DVR setup.  He said that I could only have one DVR setup for remote access, is that true?  If not, any assistance would be much appreciated. 
    Thank you!
    Are you speaking of Remote Access from the Web?  ...or from a mobile phone?
    For Web Access it is absolutely NOT TRUE!
    I have TWO DVRs.  I can access both remotely from the web and schedule or delete recordings.
    The tech MAY have been speaking of (or confused about) the MULTI-ROOM capability that the DVR's have.
    Only one of the DVRs can be (and is) a Home Media (or Multi-Room) DVR, and therefore can share recordings with my other NON-DVR STB and communicates with any computer on my home network for PC-based Audio, Vieo and Image files, as well as connecting to the certain Internet video streaming sites.
    The other DVR is a standalone machine is this regard, but regardless, it still has remote access to control it from the Web.
    (I do not know anything about the Remote Access from a mobile phone capability, since I do have a Verizon Wireless contract.  THAT Remote Access may indeed be limited to just a single DVR.)

  • I have a time capsule connected directly to fiber connection. I have connected a windows server directly to TC and configured it for remote desktop connection. From my interanet I can access srvr but not from my home. What config I need on TC?

    I have a time capsule directly connected to fibre optic point out. All pcs and macs are connected wirelessly to the internet. I have connected a windows server pc to TC. When configured for Remote desktop connection, I can access windows server from within interanet but don't know how to access it from internet. I guess I need to change some settings in TC to get some ip adress for the remote desktop connection from my home. Anyone who can help me out? Appreciate it.
    Narmin

    I am a little lost now.. I have read again your title and your first post.. and they seem inconsistent.
    In the title you state.
    From my interanet I can access srvr but not from my home.
    Interanet is not a word I know.. I assumed intranet...are you talking about internet or intranet? And just to be clear say WAN or LAN.. !! Is your home part of the interanet??
    In the first post you state,
    I can access windows server from within interanet but don't know how to access it from internet.
    Now this is more normal.. the issue is not in the home at all, it is accessible from there but fails from internet. If this is correct, then you can do a few obvious things to determine where the problem is.
    But first I need to know are you actually testing from a different internet connection to your home lan.. you are not just trying the public IP from inside the LAN as that will fail due to the TC not doing NAT Loopback.
    I am also assuming the TC is the only router in the network, and has the public IP on the WAN interface.
    And I am also assuming you have turned on the ping responder and you can actually ping your public ip from the internet and get a response. This helps no end in figuring out where there are issues. Strange but I have no idea if there is a ping responder in the TC WAN so you might need to forward that as well. Also if you have a dynamic public ip address are you using dyndns or no-ip or some other service to connect.
    1. Test bypassing the TC.. plug the internet connection straight into the windows server,, and test if you have access. If yes, the TC is the problem.. if not, your setup on the windows server is wrong.. look at firewall in particular.
    2. Assuming from test 1 the TC is the problem, Post the screen shots of the port forwarding setup for us to look at.. that is by far the easiest way to check it out.
    There are lots of references to port forwarding in the TC.. eg
    http://must-know-mac.blogspot.com/2008/07/how-to-port-forward-time-capsule.html
    The things that generally go wrong are firewall on the computer that is accepting the port.
    The ISP doesn't allow connections on a particular port. (not likely in your case)
    The router is behind another router.. double NAT will kill any port forward.
    Upnp has already allocated a port.. not an issue as TC doesn't use upnp although a reboot of everything after you set port forwards is well worth it.. amazing how things don't stick properly without a reboot.
    IP on the receiving device is not static and so changes.
    Not enough or right type of ports are opened. This is always messier than it looks as one port is often not enough for two way communications.

  • Help needed with printer settings for wired ethernet connection

    I'm hoping someone can help me with a network printing issue. I have a large format color laser printer (Tektronix Phaser) and since moving to OS 10.6 I can't figure out how to configure the printer so that the system sees it. I have a simple wired ethernet network with a couple of Macs and a couple of printers. All devices are connected via a switch. When using earlier OSs I was able to connect to the Phaser using Ethertalk. Obviously this is no longer supported and I can't figure out how to set the printer so the OS can see it. I have lots of options which can be turned on or off and in some cases set up in other ways: Ethertalk, IPX, Netware, TCP/IP, DNS, LPR, HTTP and remote internet printing, I've tried messing with these but the result is always the same--system doesn't see the printer. Currently Ethertalk is on, IPX and Netware are off, TCP/IP is on, DNS and LPR are on, as are AppSocket, HTTP, FTP and remote internet printing. I can change the IP address but no matter what address I've tried I cannot ping the printer. (I'm using a Gutenprint driver for this printer.)
    I don't really know enough about all this to get anywhere and I haven't been able to find help anywhere even from tech friends. Xerox won't help me and neither will Apple. Any help would be appreciated. I can supply more detail on specifics where necessary. Thanks, Bob

    Old Phaser models may becoming more and more difficult to use, but you can give this a try.
    1. Configure the printer via front panel to use TCP/IP and enable DHCP if it's supported. If not then you will need to configure an IP address for the printer together with your local network's mask, and gateway IP address. Except for the first the others will be provided by opening Network preferences to see what those settings are. The printer's IP address needs to be set somewhere within the range of IP addresses your router provides locally.
    2. You need the PPD file required for your printer. If you have the Phaser driver installer you can use it to install the PPD or you can extract the specific PPD from the installer package. This part is tricky because I don't know where you may find the driver now if you don't have the installer. The older installers can be accessed through the Finder by selecting the package then CTRL- or RIGHT-click and select Show Package Contents from the contextual menu. You can then rummage through the package to search for the PPD for your printer. Then navigate to the /Library/Printers/PPD/Contents/Resources/ folder and drop the PPD file inside.
    3. Open Print & Fax preferences and click on Add [+] to add a new printer. Click on the IP icon in the toolbar. Select Line Printer Daemon - LPD from the Protocol drop down menu. Input the IP address you assigned the printer in the Address field. You can file in the optional fields that follow. Then from the Print Using drop down menu locate the listing for your printer and select it.

Maybe you are looking for