Display flickers on start up
My display flickers slowly when coming out of sleep or booting up. After a short while the monitor works perfectly. After it goes into sleep mode, or when the screen saver goes dark, upon awakening the flicker starts again. I recently replaced my ATI Radeon HD 5770 graphics card and VGA cable that connects to Mini Displayport / VGA adapter. Any idea what the problem might be and how to fix?
Converting Mini DisplayPort to VGA is fairly difficult.
If you are not using the larger DVI-I port, I suggest you buy a cheap adapter that pulls the Card-generated VGA directly off that -- no conversion required. The VGA signals are in the bar at the end and the four pins around it, plus one more pin from the top row of the grid. Salmon-pink in this diagram:
--diagram courtesy of Wikipedia
Similar Messages
-
My macbook air (version 10.9.4) display flickers, has random tabs and windows opening, and there are random ads almost everywhere. All this happens when I am using safari. What can I do?
1. This procedure is a diagnostic test. It changes nothing, for better or worse, and therefore will not, in itself, solve the problem. But with the aid of the test results, the solution may take a few minutes, instead of hours or days.
Don't be put off merely by the seeming complexity of these instructions. The process is much less complicated than the description. You do harder tasks with the computer all the time.
2. If you don't already have a current backup, back up all data before doing anything else. The backup is necessary on general principle, not because of anything in the test procedure. Backup is always a must, and when you're having any kind of trouble with the computer, you may be at higher than usual risk of losing data, whether you follow these instructions or not.
There are ways to back up a computer that isn't fully functional. Ask if you need guidance.
3. Below are instructions to run a UNIX shell script, a type of program. As I wrote above, it changes nothing. It doesn't send or receive any data on the network. All it does is to generate a human-readable report on the state of the computer. That report goes nowhere unless you choose to share it. If you prefer, you can read it yourself without disclosing the contents to me or anyone else.
You should be wondering whether you can believe me, and whether it's safe to run a program at the behest of a stranger. In general, no, it's not safe and I don't encourage it.
In this case, however, there are a couple of ways for you to decide whether the program is safe without having to trust me. First, you can read it. Unlike an application that you download and click to run, it's transparent, so anyone with the necessary skill can verify what it does.
You may not be able to understand the script yourself. But variations of the script have been posted on this website thousands of times over a period of years. The site is hosted by Apple, which does not allow it to be used to distribute harmful software. Any one of the millions of registered users could have read the script and raised the alarm if it was harmful. Then I would not be here now and you would not be reading this message.
Nevertheless, if you can't satisfy yourself that these instructions are safe, don't follow them. Ask for other options.
4. Here's a summary of what you need to do, if you choose to proceed:
☞ Copy a line of text in this window to the Clipboard.
☞ Paste into the window of another application.
☞ Wait for the test to run. It usually takes a few minutes.
☞ Paste the results, which will have been copied automatically, back into a reply on this page.
The sequence is: copy, paste, wait, paste again. You don't need to copy a second time. Details follow.
5. You may have started the computer in "safe" mode. Preferably, these steps should be taken in “normal” mode, under the conditions in which the problem is reproduced. If the system is now in safe mode and works well enough in normal mode to run the test, restart as usual. If you can only test in safe mode, do that.
6. If you have more than one user, and the one affected by the problem is not an administrator, then please run the test twice: once while logged in as the affected user, and once as an administrator. The results may be different. The user that is created automatically on a new computer when you start it for the first time is an administrator. If you can't log in as an administrator, test as the affected user. Most personal Macs have only one user, and in that case this section doesn’t apply. Don't log in as root.
7. The script is a single long line, all of which must be selected. You can accomplish this easily by triple-clicking anywhere in the line. The whole line will highlight, though you may not see all of it in the browser window, and you can then copy it. If you try to select the line by dragging across the part you can see, you won't get all of it.
Triple-click anywhere in the line of text below on this page to select it:
PATH=/usr/bin:/bin:/usr/sbin:/sbin:/usr/libexec;clear;cd;p=(Software Hardware Memory Diagnostics Power FireWire Thunderbolt USB Fonts SerialATA 4 1000 25 5120 KiB/s 1024 85 \\b%% 20480 1 MB/s 25000 ports ' com.clark.\* \*dropbox \*GoogleDr\* \*k.AutoCAD\* \*k.Maya\* vidinst\* ' DYLD_INSERT_LIBRARIES\ DYLD_LIBRARY_PATH -86 ` route -n get default|awk '/e:/{print $2}' ` 25 N\\/A down up 102400 25600 recvfrom sendto CFBundleIdentifier 25 25 25 1000 MB com.apple.AirPortBaseStationAgent 464843899 51 5120 files );N5=${#p[@]};p[N5]=` networksetup -listnetworkserviceorder|awk ' NR>1 { sub(/^\([0-9]+\) /,"");n=$0;getline;} $NF=="'${p[26]}')" { sub(/.$/,"",$NF);print n;exit;} ' `;f=('\n%s: %s\n' '\n%s\n\n%s\n' '\nRAM details\n%s\n' %s\ %s '%s\n-\t%s\n' );S0() { echo ' { q=$NF+0;$NF="";u=$(NF-1);$(NF-1)="";gsub(/^ +| +$/,"");if(q>='${p[$1]}') printf("%s (UID %s) is using %s '${p[$2]}'",$0,u,q);} ';};s=(' /^ *$|CSConfigDot/d;s/^ */ /;s/[-0-9A-Fa-f]{22,}/UUID/g;s/(ochat)\.[^.]+(\..+)/\1\2/;/Shared/!s/\/Users\/[^/]+/~/g ' ' s/^ +//;/(de|[nst]):/p;' ' {sub(/^ +/,"")};/r:/;/y:/&&$2<'${p[10]} ' 1s/://;3,6d;/[my].+:/d;s/^ {4}//;H;${ g;s/\n$//;/s: [^EO]|x([^08]|02[^F]|8[^0])/p;} ' ' 5h;6{ H;g;/P/!p;} ' ' ($1~/^Cy/&&$3>'${p[11]}')||($1~/^Cond/&&$2!~/^N/) ' ' /:$/{ N;/:.+:/d;s/ *://;b0'$'\n'' };/^ *(V.+ [0N]|Man).+ /{ s/ 0x.... //;s/[()]//g;s/(.+: )(.+)/ (\2)/;H;};$b0'$'\n'' d;:0'$'\n'' x;s/\n\n//;/Apple[ ,]|Intel|SMSC/d;s/\n.*//;/\)$/p;' ' s/^.*C/C/;H;${ g;/No th|pms/!p;} ' '/= [^GO]/p' '{$1=""};1' ' /Of/!{ s/^.+is |\.//g;p;} ' ' $0&&!/ / { n++;print;} END { if(n<200) print "com.apple.";} ' ' $3~/[0-9]:[0-9]{2}$/ { gsub(/:[0-9:a-f]{14}/,"");} { print|"tail -n'${p[12]}'";} ' ' NR==2&&$4<='${p[13]}' { print $4;} ' ' END { $2/=256;if($2>='${p[15]}') print int($2) } ' ' NR!=13{next};{sub(/[+-]$/,"",$NF)};'"`S0 21 22`" 'NR!=2{next}'"`S0 37 17`" ' NR!=5||$8!~/[RW]/{next};{ $(NF-1)=$1;$NF=int($NF/10000000);for(i=1;i<=3;i++){$i="";$(NF-1-i)="";};};'"`S0 19 20`" 's:^:/:p' '/\.kext\/(Contents\/)?Info\.plist$/p' 's/^.{52}(.+) <.+/\1/p' ' /Launch[AD].+\.plist$/ { n++;print;} END { print "'${p[41]}'";if(n<200) print "/System/";} ' '/\.xpc\/(Contents\/)?Info\.plist$/p' ' NR>1&&!/0x|\.[0-9]+$|com\.apple\.launchctl\.(Aqua|Background|System)$|'${p[41]}'/ { print $3;} ' ' /\.(framew|lproj)|\):/d;/plist:|:.+(Mach|scrip)/s/:[^:]+//p ' '/^root$/p' ' !/\/Contents\/.+\/Contents|Applic|Autom|Frameworks/&&/Lib.+\/Info.plist$/ { n++;print;} END { if(n<1100) print "/System/";} ' '/^\/usr\/lib\/.+dylib$/p' ' /Temp|emac/{next};/(etc|Preferences|Launch[AD].+)\// { sub(".(/private)?","");n++;print;} END { print "'${p[41]}'.plist\t'${p[42]}'";if(n<500) print "Launch";} ' ' /\/(Contents\/.+\/Contents|Frameworks)\/|\.wdgt\/.+\.([bw]|plu)/d;p;' 's/\/(Contents\/)?Info.plist$//;p' ' { gsub("^| |\n","\\|\\|kMDItem'${p[35]}'=");sub("^...."," ") };1 ' p '{print $3"\t"$1}' 's/\'$'\t''.+//p' 's/1/On/p' '/Prox.+: [^0]/p' '$2>'${p[43]}'{$2=$2-1;print}' ' BEGIN { i="'${p[26]}'";M1='${p[16]}';M2='${p[18]}';M3='${p[31]}';M4='${p[32]}';} !/^A/{next};/%/ { getline;if($5<M1) a="user "$2"%, system "$4"%";} /disk0/&&$4>M2 { b=$3" ops/s, "$4" blocks/s";} $2==i { if(c) { d=$3+$4+$5+$6;next;};if($4>M3||$6>M4) c=int($4/1024)" in, "int($6/1024)" out";} END { if(a) print "CPU: "a;if(b) print "I/O: "b;if(c) print "Net: "c" (KiB/s)";if(d) print "Net errors: "d" packets/s";} ' ' /r\[0\] /&&$NF!~/^1(0|72\.(1[6-9]|2[0-9]|3[0-1])|92\.168)\./ { print $NF;exit;} ' ' !/^T/ { printf "(static)";exit;} ' '/apsd|BKAg|OpenD/!s/:.+//p' ' (/k:/&&$3!~/(255\.){3}0/ )||(/v6:/&&$2!~/A/ ) ' ' $1~"lR"&&$2<='${p[25]}';$1~"li"&&$3!~"wpa2";' ' BEGIN { FS=":";} { n=split($3,a,".");sub(/_2[01].+/,"",$3);print $2" "$3" "a[n]" "$1;b=b$1;} END { if(b) print("\n\t* Code injection");} ' ' NR!=4{next} {$NF/=10240} '"`S0 27 14`" ' END { if($3~/[0-9]/)print$3;} ' ' BEGIN { L='${p[36]}';} !/^[[:space:]]*(#.*)?$/ { l++;if(l<=L) f=f"\n "$0;} END { F=FILENAME;if(!F) exit;if(!f) f="\n [N/A]";"file -b "F|getline T;if(T!~/^(AS.+ (En.+ )?text$|POSIX sh.+ text ex)/) F=F" ("T")";printf("\nContents of %s\n%s\n",F,f);if(l>L) printf("\n ...and %s more line(s)\n",l-L);} ' ' /^ +[NP].+ =/h;/^( +D.+[{]|[}])/{ g;s/.+= //p;};' 's/0/Off/p' ' END{print NR} ' ' /id: N|te: Y/{i++} END{print i} ' ' / / { print "'"${p[28]}"'";exit;};1;' '/ en/!s/\.//p' ' NR!=13{next};{sub(/[+-M]$/,"",$NF)};'"`S0 39 40`" ' $10~/\(L/&&$9!~"localhost" { sub(/.+:/,"",$9);print $1": "$9;} ' '/^ +r/s/.+"(.+)".+/\1/p' 's/(.+\.wdgt)\/(Contents\/)?Info\.plist$/\1/p' 's/^.+\/(.+)\.wdgt$/\1/p' ' /l: /{ /DVD/d;s/.+: //;b0'$'\n'' };/s: /{ /V/d;s/^ */- /;H;};$b0'$'\n'' d;:0'$'\n'' x;/APPLE [^:]+$/d;p;' ' /^find: /d;p;' "`S0 44 45`" );c1=(system_profiler pmset\ -g nvram fdesetup find syslog df vm_stat sar ps sudo\ crontab sudo\ iotop top pkgutil 'PlistBuddy 2>&1 -c "Print' whoami cksum kextstat launchctl sudo\ launchctl crontab 'sudo defaults read' stat lsbom mdfind ' for i in ${p[24]};do ${c1[18]} ${c2[27]} $i;done;' defaults\ read scutil sudo\ dtrace sudo\ profiles sed\ -En awk /S*/*/P*/*/*/C*/*/airport networksetup mdutil sudo\ lsof test );c2=(com.apple.loginwindow\ LoginHook '" /L*/P*/loginw*' '" L*/P*/*loginit*' 'L*/Ca*/com.ap*.Saf*/E*/* -d 1 -name In*t -exec '"${c1[14]}"' :CFBundleDisplayName" {} \;|sort|uniq' '~ $TMPDIR.. \( -flags +sappnd,schg,uappnd,uchg -o ! -user $UID -o ! -perm -600 \)' '.??* -path .Trash -prune -o -type d -name *.app -print -prune' :${p[35]}\" :Label\" '{/,}L*/{Con,Pref}* -type f ! -size 0 -name *.plist -exec plutil -s {} \;' "-f'%N: %l' Desktop L*/Keyc*" therm sysload boot-args status " -F '\$Time \$Message' -k Sender kernel -k Message Req 'bad |Beac|caug|dead[^bl]|FAIL|fail|GPU |hfs: Ru|inval|jnl:|last value [1-9]|n Cause: -|NVDA\(|pagin|proc: t|Roamed|rror|ssert|Thrott|tim(ed? ?|ing )o|WARN' -k Message Rne 'Goog|ksadm|SMC:' -o -k Sender fseventsd -k Message Req 'SL' " '-du -n DEV -n EDEV 1 10' 'acrx -o comm,ruid,%cpu' '-t1 10 1' '-f -pfc /var/db/r*/com.apple.*.{BS,Bas,Es,J,OSXU,Rem,up}*.bom' '{/,}L*/Lo*/Diag* -type f -regex .\*[cgh] ! -name *ag \( -exec grep -lq "^Thread c" {} \; -exec printf \* \; -o -true \) -execdir stat -f:%Sc:%N -t%F {} \;|sort -t: -k2 |tail -n'${p[38]} '-L {/{S*/,},}L*/Lau* -type f' '-L /{S*/,}L*/StartupItems -type f -exec file {} +' '-L /S*/L*/{C*/Sec*A,E}* {/,}L*/{A*d,Ca*/*/Ex,Compon,Ex,Inter,iTu,Keyb,Mail/B,Pr*P,Qu*T,Scripti,Sec,Servi,Spo,Widg}* -type f -name Info.plist' '/usr/lib -type f -name *.dylib' `awk "${s[31]}"<<<${p[23]}` "/e*/{auto,{cron,fs}tab,hosts,{[lp],sy}*.conf,pam.d/*,ssh{,d}_config,*.local} {,/usr/local}/etc/periodic/*/* /L*/P*{,/*}/com.a*.{Bo,sec*.ap}*t /S*/L*/Lau*/*t .launchd.conf" list getenv /Library/Preferences/com.apple.alf\ globalstate --proxy '-n get default' -I --dns -getdnsservers\ "${p[N5]}" -getinfo\ "${p[N5]}" -P -m\ / '' -n1 '-R -l1 -n1 -o prt -stats command,uid,prt' '--regexp --only-files --files com.apple.pkg.*|sort|uniq' -kl -l -s\ / '-R -l1 -n1 -o mem -stats command,uid,mem' '+c0 -i4TCP:0-1023' com.apple.dashboard\ layer-gadgets '-d /L*/Mana*/$USER&&echo On' '-app Safari WebKitDNSPrefetchingEnabled' "+c0 -l|awk '{print(\$1,\$3)}'|sort|uniq -c|sort -n|tail -1|awk '{print(\$2,\$3,\$1)}'" );N1=${#c2[@]};for j in {0..9};do c2[N1+j]=SP${p[j]}DataType;done;N2=${#c2[@]};for j in 0 1;do c2[N2+j]="-n ' syscall::'${p[33+j]}':return { @out[execname,uid]=sum(arg0) } tick-10sec { trunc(@out,1);exit(0);} '";done;l=(Restricted\ files Hidden\ apps 'Elapsed time (s)' POST Battery Safari\ extensions Bad\ plists 'High file counts' User Heat System\ load boot\ args FileVault Diagnostic\ reports Log 'Free space (MiB)' 'Swap (MiB)' Activity 'CPU per process' Login\ hook 'I/O per process' Mach\ ports kexts Daemons Agents launchd Startup\ items Admin\ access Root\ access Bundles dylibs Apps Font\ issues Inserted\ dylibs Firewall Proxies DNS TCP/IP Wi-Fi Profiles Root\ crontab User\ crontab 'Global login items' 'User login items' Spotlight Memory Listeners Widgets Parental\ Controls Prefetching SATA Descriptors );N3=${#l[@]};for i in 0 1 2;do l[N3+i]=${p[5+i]};done;N4=${#l[@]};for j in 0 1;do l[N4+j]="Current ${p[29+j]}stream data";done;A0() { id -G|grep -qw 80;v[1]=$?;((v[1]==0))&&sudo true;v[2]=$?;v[3]=`date +%s`;clear >&-;date '+Start time: %T %D%n';};for i in 0 1;do eval ' A'$((1+i))'() { v=` eval "${c1[$1]} ${c2[$2]}"|'${c1[30+i]}' "${s[$3]}" `;[[ "$v" ]];};A'$((3+i))'() { v=` while read i;do [[ "$i" ]]&&eval "${c1[$1]} ${c2[$2]}" \"$i\"|'${c1[30+i]}' "${s[$3]}";done<<<"${v[$4]}" `;[[ "$v" ]];};A'$((5+i))'() { v=` while read i;do '${c1[30+i]}' "${s[$1]}" "$i";done<<<"${v[$2]}" `;[[ "$v" ]];};';done;A7(){ v=$((`date +%s`-v[3]));};B2(){ v[$1]="$v";};for i in 0 1;do eval ' B'$i'() { v=;((v['$((i+1))']==0))||{ v=No;false;};};B'$((3+i))'() { v[$2]=`'${c1[30+i]}' "${s[$3]}"<<<"${v[$1]}"`;} ';done;B5(){ v[$1]="${v[$1]}"$'\n'"${v[$2]}";};B6() { v=` paste -d: <(printf "${v[$1]}") <(printf "${v[$2]}")|awk -F: ' {printf("'"${f[$3]}"'",$1,$2)} ' `;};B7(){ v=`grep -Fv "${v[$1]}"<<<"$v"`;};C0(){ [[ "$v" ]]&&echo "$v";};C1() { [[ "$v" ]]&&printf "${f[$1]}" "${l[$2]}" "$v";};C2() { v=`echo $v`;[[ "$v" != 0 ]]&&C1 0 $1;};C3() { v=`sed -E "$s"<<<"$v"`&&C1 1 $1;};for i in 1 2;do for j in 0 2 3;do eval D$i$j'(){ A'$i' $1 $2 $3; C'$j' $4;};';done;done;{ A0;D20 0 $((N1+1)) 2;D10 0 $N1 1;B0;C2 27;B0&&! B1&&C2 28;D12 15 37 25 8;A1 0 $((N1+2)) 3;C0;D13 0 $((N1+3)) 4 3;D23 0 $((N1+4)) 5 4;D13 0 $((N1+9)) 59 50;for i in 0 1 2;do D13 0 $((N1+5+i)) 6 $((N3+i));done;D13 1 10 7 9;D13 1 11 8 10;D22 2 12 9 11;D12 3 13 10 12;D23 4 19 44 13;D23 5 14 12 14;D22 6 36 13 15;D22 7 37 14 16;D23 8 15 38 17;D22 9 16 16 18;B1&&{ D22 35 49 61 51;D22 11 17 17 20;for i in 0 1;do D22 28 $((N2+i)) 45 $((N4+i));done;};D22 12 44 54 45;D22 12 39 15 21;A1 13 40 18;B2 4;B3 4 0 19;A3 14 6 32 0;B4 0 5 11;A1 17 41 20;B7 5;C3 22;B4 4 6 21;A3 14 7 32 6;B4 0 7 11;B3 4 0 22;A3 14 6 32 0;B4 0 8 11;B5 7 8;B1&&{ A2 19 26 23;B7 7;C3 23;};A2 18 26 23;B7 7;C3 24;A2 4 20 21;B7 6;B2 9;A4 14 7 52 9;B2 10;B6 9 10 4;C3 25;D13 4 21 24 26;B4 4 12 26;B3 4 13 27;A1 4 22 29;B7 12;B2 14;A4 14 6 52 14;B2 15;B6 14 15 4;B3 0 0 30;C3 29;A1 4 23 27;B7 13;C3 30;D13 24 24 32 31;D13 25 37 32 33;A2 23 18 28;B2 16;A2 16 25 33;B7 16;B3 0 0 34;B2 21;A6 47 21&&C0;B1&&{ D13 21 0 32 19;D13 10 42 32 40;D22 29 35 46 39;};D13 14 1 48 42;D12 34 43 53 44;D22 0 $((N1+8)) 51 32;D13 4 8 41 6;D12 26 28 35 34;D13 27 29 36 35;A2 27 32 39&&{ B2 19;A2 33 33 40;B2 20;B6 19 20 3;};C2 36;D23 33 34 42 37;B1&&D23 35 45 55 46;D23 32 31 43 38;D12 36 47 32 48;D13 20 42 32 41;D13 14 2 48 43;D13 4 5 32 1;D13 4 3 60 5;D12 26 48 49 49;B3 4 22 57;A1 26 46 56;B7 22;B3 0 0 58;C3 47;D22 4 4 50 0;D23 22 9 37 7;A7;C2 2;} 2>/dev/null|pbcopy;exit 2>&-
Copy the selected text to the Clipboard by pressing the key combination command-C.
8. Launch the built-in Terminal application in any of the following ways:
☞ Enter the first few letters of its name into a Spotlight search. Select it in the results (it should be at the top.)
☞ In the Finder, select Go ▹ Utilities from the menu bar, or press the key combination shift-command-U. The application is in the folder that opens.
☞ Open LaunchPad. Click Utilities, then Terminal in the icon grid.
Click anywhere in the Terminal window and paste by pressing command-V. The text you pasted should vanish immediately. If it doesn't, press the return key.
9. If you see an error message in the Terminal window such as "Syntax error" or "Event not found," enter
exec bash
and press return. Then paste the script again.
10. If you're logged in as an administrator, you'll be prompted for your login password. Nothing will be displayed when you type it. You will not see the usual dots in place of typed characters. Make sure caps lock is off. Type carefully and then press return. You may get a one-time warning to be careful. If you make three failed attempts to enter the password, the test will run anyway, but it will produce less information. In most cases, the difference is not important. If you don't know the password, or if you prefer not to enter it, press the key combination control-C or just press return three times at the password prompt. Again, the script will still run.
If you're not logged in as an administrator, you won't be prompted for a password. The test will still run. It just won't do anything that requires administrator privileges.
11. The test may take a few minutes to run, depending on how many files you have and the speed of the computer. A computer that's abnormally slow may take longer to run the test. While it's running, there will be nothing in the Terminal window and no indication of progress. Wait for the line
[Process completed]
to appear. If you don't see it within half an hour or so, the test probably won't complete in a reasonable time. In that case, close the Terminal window and report the results. No harm will be done.
12. When the test is complete, quit Terminal. The results will have been copied to the Clipboard automatically. They are not shown in the Terminal window. Please don't copy anything from there. All you have to do is start a reply to this comment and then paste by pressing command-V again.
At the top of the results, there will be a line that begins with the words "Start Time." If you don't see that, but instead see a mass of gibberish, you didn't wait for the "Process completed" message to appear in the Terminal window. Please wait for it and try again.
If any private information, such as your name or email address, appears in the results, anonymize it before posting. Usually that won't be necessary.
13. When you post the results, you might see an error message on the web page: "You have included content in your post that is not permitted," or "You are not authorized to post." That's a bug in the forum software. Please post the test results on Pastebin, then post a link here to the page you created.
14. This is a public forum, and others may give you advice based on the results of the test. They speak only for themselves, and I don't necessarily agree with them.
Copyright © 2014 by Linc Davis. As the sole author of this work, I reserve all rights to it except as provided in the Use Agreement for the Apple Support Communities website ("ASC"). Readers of ASC may copy it for their own personal use. Neither the whole nor any part may be redistributed. -
My display flickers and shuts off only when I first start up my Macbook Pro. I can open and close the lid to get it to completely shut off. Any ideas?
Hello shabbdaddy,
After reviewing your post, it sounds like the display flickers only when booting the computer. I would recommend that you read this article, it may be able to help the issue.
Apple computers: Troubleshooting issues with video on internal or external displays - Apple Support
Thanks for using Apple Support Communities.
Have a nice day,
Mario -
Imac 21.5 (ver 10.6.8) Display flickers and it goes blank
Display flickers and its brightness automatically increases and decreases intermittently. After some time the Display goes blank and it doesn't appear even after pressing the power button or restarting the PC. At times it does appear after pressing the power button frequently or if the PC is left ON for some time. I am using software ver 10.6.8. Want to whether this problem will be resolved after upgrading it to Mavericks. But I am worried that during the downloading if the display goes off and if I have to restart the PC then I will have to start the downloading from the beginning. Please suggest.
If you live near an Apple Store, make a Genius Bar appointment to have the computer tested. Supposedly there is no charge for testing. Use 2nd link if not near an Apple Store or aren’t in the US.
Genius Bar Reservation US
Authorized Service Provider -
27 Cinema Display flickers on cursor change
Hello,
I've recently purchased a 27" Cinema Display and hooked it up to my mid 2010 13" MBP. Everything works fine except for one really annoying thing: The Cinema Display flickers when the mouse cursor changes. I've done a thorough search through the community threads and haven't found anybody who's experiencing the same problem. Could anyone please tell me if they've run into this issue, and if so if there's any way of fixing it.
Thanks!Might be related to the thread below.
To give you a quick summary, try either of the following:
- use your macbook's charger rather than the cinema display magsafe connector
- increase the brightness to 7 bars or more
- simply unplug the magsafe used by the cinema display
https://discussions.apple.com/thread/2669791?start=30&tstart=0 -
External Display Flickers (Intel on board)
Hi,
I have recently made a fresh installation of Arch Linux and trying to setup it for my work environment. I made a basic installation of xfce4 with slim login manager. I wanted to hook my laptop with an external display. I used xrandr to extend my laptop display with the external display. Everything worked fine but my external display flickers insanely bad. I cannot stare at it for > 30s. I dual boot on windows, so I tested the same setup with windows and it worked just fine, out of the box. I even used one of my friend's laptop who's running ubuntu and has the same h/w. It worked out of the box. I have spent more than 8 hours trying to find out where the issue would be and miserably failed. Below are certain logs and output that might help traingulate my issue.
Its a Dell Inspiron N4030, with Intel onboard graphics. I have the xf86-video-intel driver installed and the display works perfectly fine with laptops default display.
Output of xrandr -q
[joker@lucifer ~]$ xrandr -q
Screen 0: minimum 320 x 200, current 2732 x 768, maximum 8192 x 8192
LVDS1 connected 1366x768+0+0 (normal left inverted right x axis y axis) 309mm x 173mm
1366x768 60.0*+
1024x768 60.0
800x600 60.3 56.2
640x480 59.9
VGA1 connected 1366x768+1366+0 (normal left inverted right x axis y axis) 344mm x 194mm
1366x768 60.0*+
1024x768 75.1 72.0 70.1 60.0
832x624 74.6
800x600 72.2 75.0 60.3 56.2
640x480 72.8 75.0 66.7 60.0
720x400 70.1
/var/log/Xorg.0.log
[ 42.854]
X.Org X Server 1.11.2
Release Date: 2011-11-04
[ 42.854] X Protocol Version 11, Revision 0
[ 42.854] Build Operating System: Linux 3.1.0-3-ARCH x86_64
[ 42.854] Current Operating System: Linux lucifer 3.1.0-4-ARCH #1 SMP PREEMPT Mon Nov 7 22:47:18 CET 2011 x86_64
[ 42.854] Kernel command line: root=/dev/sda5 ro
[ 42.854] Build Date: 07 November 2011 07:53:00AM
[ 42.854]
[ 42.854] Current version of pixman: 0.24.0
[ 42.854] Before reporting problems, check http://wiki.x.org
to make sure that you have the latest version.
[ 42.854] Markers: (--) probed, (**) from config file, (==) default setting,
(++) from command line, (!!) notice, (II) informational,
(WW) warning, (EE) error, (NI) not implemented, (??) unknown.
[ 42.855] (==) Log file: "/var/log/Xorg.0.log", Time: Thu Nov 10 17:07:34 2011
[ 42.901] (==) Using config directory: "/etc/X11/xorg.conf.d"
[ 42.927] (==) ServerLayout "DualSreen"
[ 42.927] (**) |-->Screen "Screen0" (0)
[ 42.927] (**) | |-->Monitor "Monitor0"
[ 42.945] (**) | |-->Device "Device0"
[ 42.945] (**) |-->Screen "Screen1" (1)
[ 42.945] (**) | |-->Monitor "Monitor1"
[ 42.945] (**) | |-->Device "Device1"
[ 42.945] (**) Option "Xinerama" "1"
[ 42.945] (==) Automatically adding devices
[ 42.945] (==) Automatically enabling devices
[ 42.945] (**) Xinerama: enabled
[ 43.004] (WW) The directory "/usr/share/fonts/OTF/" does not exist.
[ 43.004] Entry deleted from font path.
[ 43.004] (WW) The directory "/usr/share/fonts/Type1/" does not exist.
[ 43.004] Entry deleted from font path.
[ 43.005] (WW) `fonts.dir' not found (or not valid) in "/usr/share/fonts/100dpi/".
[ 43.005] Entry deleted from font path.
[ 43.005] (Run 'mkfontdir' on "/usr/share/fonts/100dpi/").
[ 43.005] (WW) `fonts.dir' not found (or not valid) in "/usr/share/fonts/75dpi/".
[ 43.005] Entry deleted from font path.
[ 43.005] (Run 'mkfontdir' on "/usr/share/fonts/75dpi/").
[ 43.005] (==) FontPath set to:
/usr/share/fonts/misc/,
/usr/share/fonts/TTF/
[ 43.005] (==) ModulePath set to "/usr/lib/xorg/modules"
[ 43.005] (II) The server relies on udev to provide the list of input devices.
If no devices become available, reconfigure udev or disable AutoAddDevices.
[ 43.005] (II) Loader magic: 0x7ccae0
[ 43.005] (II) Module ABI versions:
[ 43.005] X.Org ANSI C Emulation: 0.4
[ 43.005] X.Org Video Driver: 11.0
[ 43.005] X.Org XInput driver : 13.0
[ 43.005] X.Org Server Extension : 6.0
[ 43.006] (--) PCI:*(0:0:2:0) 8086:0046:1028:0466 rev 2, Mem @ 0xfac00000/4194304, 0xc0000000/268435456, I/O @ 0x0000f080/8
[ 43.006] (WW) Open ACPI failed (/var/run/acpid.socket) (No such file or directory)
[ 43.006] (II) LoadModule: "extmod"
[ 43.027] (II) Loading /usr/lib/xorg/modules/extensions/libextmod.so
[ 43.043] (II) Module extmod: vendor="X.Org Foundation"
[ 43.043] compiled for 1.11.2, module version = 1.0.0
[ 43.043] Module class: X.Org Server Extension
[ 43.043] ABI class: X.Org Server Extension, version 6.0
[ 43.043] (II) Loading extension MIT-SCREEN-SAVER
[ 43.043] (II) Loading extension XFree86-VidModeExtension
[ 43.043] (II) Loading extension XFree86-DGA
[ 43.043] (II) Loading extension DPMS
[ 43.043] (II) Loading extension XVideo
[ 43.043] (II) Loading extension XVideo-MotionCompensation
[ 43.043] (II) Loading extension X-Resource
[ 43.044] (II) LoadModule: "dbe"
[ 43.044] (II) Loading /usr/lib/xorg/modules/extensions/libdbe.so
[ 43.045] (II) Module dbe: vendor="X.Org Foundation"
[ 43.045] compiled for 1.11.2, module version = 1.0.0
[ 43.045] Module class: X.Org Server Extension
[ 43.045] ABI class: X.Org Server Extension, version 6.0
[ 43.045] (II) Loading extension DOUBLE-BUFFER
[ 43.045] (II) LoadModule: "glx"
[ 43.045] (II) Loading /usr/lib/xorg/modules/extensions/libglx.so
[ 43.060] (II) Module glx: vendor="X.Org Foundation"
[ 43.060] compiled for 1.11.2, module version = 1.0.0
[ 43.060] ABI class: X.Org Server Extension, version 6.0
[ 43.060] (==) AIGLX enabled
[ 43.060] (II) Loading extension GLX
[ 43.060] (II) LoadModule: "record"
[ 43.060] (II) Loading /usr/lib/xorg/modules/extensions/librecord.so
[ 43.061] (II) Module record: vendor="X.Org Foundation"
[ 43.061] compiled for 1.11.2, module version = 1.13.0
[ 43.061] Module class: X.Org Server Extension
[ 43.061] ABI class: X.Org Server Extension, version 6.0
[ 43.061] (II) Loading extension RECORD
[ 43.061] (II) LoadModule: "dri"
[ 43.061] (II) Loading /usr/lib/xorg/modules/extensions/libdri.so
[ 43.063] (II) Module dri: vendor="X.Org Foundation"
[ 43.063] compiled for 1.11.2, module version = 1.0.0
[ 43.063] ABI class: X.Org Server Extension, version 6.0
[ 43.063] (II) Loading extension XFree86-DRI
[ 43.063] (II) LoadModule: "dri2"
[ 43.063] (II) Loading /usr/lib/xorg/modules/extensions/libdri2.so
[ 43.064] (II) Module dri2: vendor="X.Org Foundation"
[ 43.064] compiled for 1.11.2, module version = 1.2.0
[ 43.064] ABI class: X.Org Server Extension, version 6.0
[ 43.064] (II) Loading extension DRI2
[ 43.064] (II) LoadModule: "intel"
[ 43.091] (II) Loading /usr/lib/xorg/modules/drivers/intel_drv.so
[ 43.114] (II) Module intel: vendor="X.Org Foundation"
[ 43.114] compiled for 1.10.99.902, module version = 2.16.0
[ 43.114] Module class: X.Org Video Driver
[ 43.114] ABI class: X.Org Video Driver, version 11.0
[ 43.114] (II) intel: Driver for Intel Integrated Graphics Chipsets: i810,
i810-dc100, i810e, i815, i830M, 845G, 854, 852GM/855GM, 865G, 915G,
E7221 (i915), 915GM, 945G, 945GM, 945GME, Pineview GM, Pineview G,
965G, G35, 965Q, 946GZ, 965GM, 965GME/GLE, G33, Q35, Q33, GM45,
4 Series, G45/G43, Q45/Q43, G41, B43, B43, Clarkdale, Arrandale,
Sandybridge Desktop (GT1), Sandybridge Desktop (GT2),
Sandybridge Desktop (GT2+), Sandybridge Mobile (GT1),
Sandybridge Mobile (GT2), Sandybridge Mobile (GT2+),
Sandybridge Server, Ivybridge Mobile (GT1), Ivybridge Mobile (GT2),
Ivybridge Desktop (GT1), Ivybridge Desktop (GT2), Ivybridge Server
[ 43.114] (++) using VT number 7
[ 43.134] (II) Loading /usr/lib/xorg/modules/drivers/intel_drv.so
[ 43.135] (II) Loading /usr/lib/xorg/modules/drivers/intel_drv.so
[ 43.135] Requested Entity already in use!
[ 43.135] (EE) Screen 1 deleted because of no matching config section.
[ 43.135] (II) UnloadModule: "intel"
[ 43.136] (II) Unloading intel
[ 43.136] drmOpenDevice: node name is /dev/dri/card0
[ 43.136] drmOpenDevice: open result is 8, (OK)
[ 43.136] drmOpenByBusid: Searching for BusID pci:0000:00:02.0
[ 43.136] drmOpenDevice: node name is /dev/dri/card0
[ 43.136] drmOpenDevice: open result is 8, (OK)
[ 43.136] drmOpenByBusid: drmOpenMinor returns 8
[ 43.136] drmOpenByBusid: drmGetBusid reports pci:0000:00:02.0
[ 43.136] (**) intel(0): Depth 24, (--) framebuffer bpp 32
[ 43.136] (==) intel(0): RGB weight 888
[ 43.136] (==) intel(0): Default visual is TrueColor
[ 43.136] (II) intel(0): Integrated Graphics Chipset: Intel(R) Arrandale
[ 43.136] (--) intel(0): Chipset: "Arrandale"
[ 43.136] (**) intel(0): Relaxed fencing enabled
[ 43.136] (**) intel(0): Wait on SwapBuffers? enabled
[ 43.136] (**) intel(0): Triple buffering? enabled
[ 43.136] (**) intel(0): Framebuffer tiled
[ 43.136] (**) intel(0): Pixmaps tiled
[ 43.136] (**) intel(0): 3D buffers tiled
[ 43.136] (**) intel(0): SwapBuffers wait enabled
[ 43.136] (==) intel(0): video overlay key set to 0x101fe
[ 43.136] (II) intel(0): Output LVDS1 using monitor section Monitor0
[ 43.136] (**) intel(0): Option "Enable" "true"
[ 43.136] (II) intel(0): found backlight control interface /sys/class/backlight/acpi_video0
[ 43.196] (II) intel(0): Output VGA1 has no monitor section
[ 43.196] (II) intel(0): EDID for output LVDS1
[ 43.196] (II) intel(0): Manufacturer: BOE Model: 58e Serial#: 0
[ 43.196] (II) intel(0): Year: 2010 Week: 1
[ 43.196] (II) intel(0): EDID Version: 1.4
[ 43.196] (II) intel(0): Digital Display Input
[ 43.196] (II) intel(0): Undefined color depth
[ 43.196] (II) intel(0): Digital interface is undefined
[ 43.196] (II) intel(0): Max Image Size [cm]: horiz.: 31 vert.: 17
[ 43.196] (II) intel(0): Gamma: 2.20
[ 43.196] (II) intel(0): No DPMS capabilities specified
[ 43.196] (II) intel(0): Supported color encodings: RGB 4:4:4 YCrCb 4:4:4
[ 43.196] (II) intel(0): First detailed timing is preferred mode
[ 43.196] (II) intel(0): Preferred mode is native pixel format and refresh rate
[ 43.196] (II) intel(0): redX: 0.574 redY: 0.335 greenX: 0.335 greenY: 0.585
[ 43.196] (II) intel(0): blueX: 0.154 blueY: 0.119 whiteX: 0.312 whiteY: 0.328
[ 43.196] (II) intel(0): Manufacturer's mask: 0
[ 43.196] (II) intel(0): Supported detailed timing:
[ 43.196] (II) intel(0): clock: 72.3 MHz Image Size: 309 x 173 mm
[ 43.196] (II) intel(0): h_active: 1366 h_sync: 1414 h_sync_end 1446 h_blank_end 1526 h_border: 0
[ 43.196] (II) intel(0): v_active: 768 v_sync: 771 v_sync_end 777 v_blanking: 790 v_border: 0
[ 43.196] (II) intel(0): Supported detailed timing:
[ 43.196] (II) intel(0): clock: 72.3 MHz Image Size: 309 x 173 mm
[ 43.196] (II) intel(0): h_active: 1366 h_sync: 1414 h_sync_end 1446 h_blank_end 1526 h_border: 0
[ 43.196] (II) intel(0): v_active: 768 v_sync: 771 v_sync_end 777 v_blanking: 790 v_border: 0
[ 43.196] (II) intel(0): KFDV9HT14101
[ 43.196] (II) intel(0): Unknown vendor-specific block 0
[ 43.196] (II) intel(0): EDID (in hex):
[ 43.196] (II) intel(0): 00ffffffffffff0009e58e0500000000
[ 43.196] (II) intel(0): 01140104801f11780a3fa09355559527
[ 43.196] (II) intel(0): 1e505400000001010101010101010101
[ 43.196] (II) intel(0): 010101010101411c56a0500016303020
[ 43.196] (II) intel(0): 360035ad1000001a411c56a050001630
[ 43.196] (II) intel(0): 3020360035ad1000001a000000fe004b
[ 43.196] (II) intel(0): 46445639814854313431303100000000
[ 43.196] (II) intel(0): 00004101940100000001010a20200000
[ 43.196] (II) intel(0): EDID vendor "BOE", prod id 1422
[ 43.196] (II) intel(0): Printing DDC gathered Modelines:
[ 43.196] (II) intel(0): Modeline "1366x768"x0.0 72.33 1366 1414 1446 1526 768 771 777 790 +hsync -vsync (47.4 kHz)
[ 43.196] (II) intel(0): Not using default mode "320x240" (doublescan mode not supported)
[ 43.196] (II) intel(0): Not using default mode "400x300" (doublescan mode not supported)
[ 43.196] (II) intel(0): Not using default mode "400x300" (doublescan mode not supported)
[ 43.196] (II) intel(0): Not using default mode "512x384" (doublescan mode not supported)
[ 43.196] (II) intel(0): Not using default mode "640x480" (doublescan mode not supported)
[ 43.196] (II) intel(0): Not using default mode "640x512" (doublescan mode not supported)
[ 43.196] (II) intel(0): Not using default mode "800x600" (doublescan mode not supported)
[ 43.196] (II) intel(0): Not using default mode "896x672" (doublescan mode not supported)
[ 43.196] (II) intel(0): Not using default mode "928x696" (doublescan mode not supported)
[ 43.196] (II) intel(0): Not using default mode "960x720" (doublescan mode not supported)
[ 43.196] (II) intel(0): Not using default mode "700x525" (doublescan mode not supported)
[ 43.196] (II) intel(0): Not using default mode "1024x768" (doublescan mode not supported)
[ 43.196] (II) intel(0): Printing probed modes for output LVDS1
[ 43.196] (II) intel(0): Modeline "1366x768"x60.0 72.33 1366 1414 1446 1526 768 771 777 790 +hsync -vsync (47.4 kHz)
[ 43.196] (II) intel(0): Modeline "1024x768"x60.0 65.00 1024 1048 1184 1344 768 771 777 806 -hsync -vsync (48.4 kHz)
[ 43.196] (II) intel(0): Modeline "800x600"x60.3 40.00 800 840 968 1056 600 601 605 628 +hsync +vsync (37.9 kHz)
[ 43.196] (II) intel(0): Modeline "800x600"x56.2 36.00 800 824 896 1024 600 601 603 625 +hsync +vsync (35.2 kHz)
[ 43.196] (II) intel(0): Modeline "640x480"x59.9 25.18 640 656 752 800 480 490 492 525 -hsync -vsync (31.5 kHz)
[ 43.255] (WW) EDID timing clock 85.75 exceeds claimed max 85MHz, fixing
[ 43.255] (II) intel(0): EDID for output VGA1
[ 43.255] (II) intel(0): Manufacturer: PHL Model: c02d Serial#: 9740
[ 43.255] (II) intel(0): Year: 2009 Week: 35
[ 43.255] (II) intel(0): EDID Version: 1.3
[ 43.255] (II) intel(0): Analog Display Input, Input Voltage Level: 0.700/0.700 V
[ 43.255] (II) intel(0): Sync: Separate
[ 43.255] (II) intel(0): Max Image Size [cm]: horiz.: 34 vert.: 19
[ 43.255] (II) intel(0): Gamma: 2.20
[ 43.255] (II) intel(0): DPMS capabilities: Off; RGB/Color Display
[ 43.255] (II) intel(0): First detailed timing is preferred mode
[ 43.255] (II) intel(0): redX: 0.635 redY: 0.335 greenX: 0.281 greenY: 0.597
[ 43.255] (II) intel(0): blueX: 0.153 blueY: 0.085 whiteX: 0.312 whiteY: 0.328
[ 43.255] (II) intel(0): Supported established timings:
[ 43.255] (II) intel(0): 720x400@70Hz
[ 43.255] (II) intel(0): 640x480@60Hz
[ 43.255] (II) intel(0): 640x480@67Hz
[ 43.255] (II) intel(0): 640x480@72Hz
[ 43.255] (II) intel(0): 640x480@75Hz
[ 43.255] (II) intel(0): 800x600@56Hz
[ 43.255] (II) intel(0): 800x600@60Hz
[ 43.255] (II) intel(0): 800x600@72Hz
[ 43.255] (II) intel(0): 800x600@75Hz
[ 43.255] (II) intel(0): 832x624@75Hz
[ 43.255] (II) intel(0): 1024x768@60Hz
[ 43.255] (II) intel(0): 1024x768@70Hz
[ 43.255] (II) intel(0): 1024x768@75Hz
[ 43.255] (II) intel(0): Manufacturer's mask: 0
[ 43.255] (II) intel(0): Supported standard timings:
[ 43.255] (II) intel(0): #0: hsize: 640 vsize 400 refresh: 70 vid: 2609
[ 43.255] (II) intel(0): #1: hsize: 1024 vsize 768 refresh: 72 vid: 19553
[ 43.255] (II) intel(0): Supported detailed timing:
[ 43.255] (II) intel(0): clock: 85.8 MHz Image Size: 344 x 194 mm
[ 43.255] (II) intel(0): h_active: 1366 h_sync: 1436 h_sync_end 1579 h_blank_end 1792 h_border: 0
[ 43.255] (II) intel(0): v_active: 768 v_sync: 771 v_sync_end 774 v_blanking: 798 v_border: 0
[ 43.255] (II) intel(0): Serial No: AU50935009740
[ 43.255] (II) intel(0): Monitor name: Philips 160E
[ 43.255] (II) intel(0): Ranges: V min: 56 V max: 76 Hz, H min: 30 H max: 60 kHz, PixClock max 86 MHz
[ 43.255] (II) intel(0): EDID (in hex):
[ 43.255] (II) intel(0): 00ffffffffffff00410c2dc00c260000
[ 43.255] (II) intel(0): 23130103682213782ab370a255489827
[ 43.255] (II) intel(0): 155054bfee00310a614c010101010101
[ 43.255] (II) intel(0): 0101010101017f2156aa51001e30468f
[ 43.255] (II) intel(0): 330058c21000001e000000ff00415535
[ 43.255] (II) intel(0): 30393335303039373430000000fc0050
[ 43.255] (II) intel(0): 68696c69707320313630450a000000fd
[ 43.255] (II) intel(0): 00384c1e3c08000a20202020202000c0
[ 43.255] (II) intel(0): Printing probed modes for output VGA1
[ 43.255] (II) intel(0): Modeline "1366x768"x60.0 85.75 1366 1436 1579 1792 768 771 774 798 +hsync +vsync (47.9 kHz)
[ 43.255] (II) intel(0): Modeline "1024x768"x75.1 78.80 1024 1040 1136 1312 768 769 772 800 +hsync +vsync (60.1 kHz)
[ 43.255] (II) intel(0): Modeline "1024x768"x72.0 78.44 1024 1080 1192 1360 768 769 772 801 -hsync +vsync (57.7 kHz)
[ 43.255] (II) intel(0): Modeline "1024x768"x70.1 75.00 1024 1048 1184 1328 768 771 777 806 -hsync -vsync (56.5 kHz)
[ 43.255] (II) intel(0): Modeline "1024x768"x60.0 65.00 1024 1048 1184 1344 768 771 777 806 -hsync -vsync (48.4 kHz)
[ 43.255] (II) intel(0): Modeline "832x624"x74.6 57.28 832 864 928 1152 624 625 628 667 -hsync -vsync (49.7 kHz)
[ 43.255] (II) intel(0): Modeline "800x600"x72.2 50.00 800 856 976 1040 600 637 643 666 +hsync +vsync (48.1 kHz)
[ 43.255] (II) intel(0): Modeline "800x600"x75.0 49.50 800 816 896 1056 600 601 604 625 +hsync +vsync (46.9 kHz)
[ 43.255] (II) intel(0): Modeline "800x600"x60.3 40.00 800 840 968 1056 600 601 605 628 +hsync +vsync (37.9 kHz)
[ 43.255] (II) intel(0): Modeline "800x600"x56.2 36.00 800 824 896 1024 600 601 603 625 +hsync +vsync (35.2 kHz)
[ 43.255] (II) intel(0): Modeline "640x480"x72.8 31.50 640 664 704 832 480 489 491 520 -hsync -vsync (37.9 kHz)
[ 43.255] (II) intel(0): Modeline "640x480"x75.0 31.50 640 656 720 840 480 481 484 500 -hsync -vsync (37.5 kHz)
[ 43.255] (II) intel(0): Modeline "640x480"x66.7 30.24 640 704 768 864 480 483 486 525 -hsync -vsync (35.0 kHz)
[ 43.255] (II) intel(0): Modeline "640x480"x60.0 25.20 640 656 752 800 480 490 492 525 -hsync -vsync (31.5 kHz)
[ 43.255] (II) intel(0): Modeline "720x400"x70.1 28.32 720 738 846 900 400 412 414 449 -hsync +vsync (31.5 kHz)
[ 43.255] (II) intel(0): Output LVDS1 enabled by config file
[ 43.255] (II) intel(0): Output VGA1 connected
[ 43.255] (II) intel(0): Using exact sizes for initial modes
[ 43.255] (II) intel(0): Output LVDS1 using initial mode 1366x768
[ 43.255] (II) intel(0): Output VGA1 using initial mode 1366x768
[ 43.255] (II) intel(0): Using default gamma of (1.0, 1.0, 1.0) unless otherwise stated.
[ 43.255] (II) intel(0): Kernel page flipping support detected, enabling
[ 43.255] (**) intel(0): Display dimensions: (310, 170) mm
[ 43.255] (**) intel(0): DPI set to (111, 114)
[ 43.255] (II) Loading sub module "fb"
[ 43.255] (II) LoadModule: "fb"
[ 43.255] (II) Loading /usr/lib/xorg/modules/libfb.so
[ 43.277] (II) Module fb: vendor="X.Org Foundation"
[ 43.277] compiled for 1.11.2, module version = 1.0.0
[ 43.277] ABI class: X.Org ANSI C Emulation, version 0.4
[ 43.277] (II) Loading sub module "dri2"
[ 43.277] (II) LoadModule: "dri2"
[ 43.277] (II) Loading /usr/lib/xorg/modules/extensions/libdri2.so
[ 43.277] (II) Module dri2: vendor="X.Org Foundation"
[ 43.277] compiled for 1.11.2, module version = 1.2.0
[ 43.277] ABI class: X.Org Server Extension, version 6.0
[ 43.277] (==) Depth 24 pixmap format is 32 bpp
[ 43.277] (II) intel(0): [DRI2] Setup complete
[ 43.277] (II) intel(0): [DRI2] DRI driver: i965
[ 43.277] (II) intel(0): Allocated new frame buffer 1408x768 stride 5632, tiled
[ 43.339] (II) UXA(0): Driver registered support for the following operations:
[ 43.339] (II) solid
[ 43.339] (II) copy
[ 43.339] (II) composite (RENDER acceleration)
[ 43.339] (II) put_image
[ 43.339] (II) get_image
[ 43.339] (==) intel(0): Backing store disabled
[ 43.339] (==) intel(0): Silken mouse enabled
[ 43.339] (II) intel(0): Initializing HW Cursor
[ 43.456] (II) intel(0): RandR 1.2 enabled, ignore the following RandR disabled message.
[ 43.466] (==) intel(0): DPMS enabled
[ 43.466] (==) intel(0): Intel XvMC decoder enabled
[ 43.466] (II) intel(0): Set up textured video
[ 43.466] (II) intel(0): [XvMC] xvmc_vld driver initialized.
[ 43.466] (II) intel(0): direct rendering: DRI2 Enabled
[ 43.466] (WW) intel(0): Option "Enable" is not used
[ 43.466] (WW) intel(0): Option "TwinView" is not used
[ 43.466] (==) intel(0): hotplug detection: "enabled"
[ 43.466] (--) RandR disabled
[ 43.466] (II) Initializing built-in extension Generic Event Extension
[ 43.466] (II) Initializing built-in extension SHAPE
[ 43.466] (II) Initializing built-in extension MIT-SHM
[ 43.466] (II) Initializing built-in extension XInputExtension
[ 43.466] (II) Initializing built-in extension XTEST
[ 43.466] (II) Initializing built-in extension BIG-REQUESTS
[ 43.466] (II) Initializing built-in extension SYNC
[ 43.466] (II) Initializing built-in extension XKEYBOARD
[ 43.466] (II) Initializing built-in extension XC-MISC
[ 43.466] (II) Initializing built-in extension SECURITY
[ 43.466] (II) Initializing built-in extension XINERAMA
[ 43.466] (II) Initializing built-in extension XFIXES
[ 43.466] (II) Initializing built-in extension RENDER
[ 43.466] (II) Initializing built-in extension RANDR
[ 43.466] (II) Initializing built-in extension COMPOSITE
[ 43.466] (II) Initializing built-in extension DAMAGE
[ 43.605] (II) AIGLX: enabled GLX_MESA_copy_sub_buffer
[ 43.605] (II) AIGLX: enabled GLX_INTEL_swap_event
[ 43.605] (II) AIGLX: enabled GLX_SGI_swap_control and GLX_MESA_swap_control
[ 43.605] (II) AIGLX: enabled GLX_SGI_make_current_read
[ 43.605] (II) AIGLX: GLX_EXT_texture_from_pixmap backed by buffer objects
[ 43.605] (II) AIGLX: Loaded and initialized i965
[ 43.605] (II) GLX: Initialized DRI2 GL provider for screen 0
[ 43.605] (II) intel(0): Setting screen physical size to 361 x 203
[ 43.909] (II) config/udev: Adding input device Power Button (/dev/input/event7)
[ 43.910] (**) Power Button: Applying InputClass "evdev keyboard catchall"
[ 43.910] (II) LoadModule: "evdev"
[ 43.910] (II) Loading /usr/lib/xorg/modules/input/evdev_drv.so
[ 43.910] (II) Module evdev: vendor="X.Org Foundation"
[ 43.910] compiled for 1.10.99.902, module version = 2.6.0
[ 43.910] Module class: X.Org XInput Driver
[ 43.910] ABI class: X.Org XInput driver, version 13.0
[ 43.910] (II) Using input driver 'evdev' for 'Power Button'
[ 43.910] (II) Loading /usr/lib/xorg/modules/input/evdev_drv.so
[ 43.911] (**) Power Button: always reports core events
[ 43.911] (**) Power Button: Device: "/dev/input/event7"
[ 43.911] (--) Power Button: Found keys
[ 43.911] (II) Power Button: Configuring as keyboard
[ 43.911] (**) Option "config_info" "udev:/sys/devices/LNXSYSTM:00/LNXPWRBN:00/input/input7/event7"
[ 43.911] (II) XINPUT: Adding extended input device "Power Button" (type: KEYBOARD, id 6)
[ 43.911] (**) Option "xkb_rules" "evdev"
[ 43.911] (**) Option "xkb_model" "evdev"
[ 43.911] (**) Option "xkb_layout" "us"
[ 43.931] (II) config/udev: Adding input device Video Bus (/dev/input/event15)
[ 43.931] (**) Video Bus: Applying InputClass "evdev keyboard catchall"
[ 43.931] (II) Using input driver 'evdev' for 'Video Bus'
[ 43.931] (II) Loading /usr/lib/xorg/modules/input/evdev_drv.so
[ 43.931] (**) Video Bus: always reports core events
[ 43.931] (**) Video Bus: Device: "/dev/input/event15"
[ 43.931] (--) Video Bus: Found keys
[ 43.931] (II) Video Bus: Configuring as keyboard
[ 43.931] (**) Option "config_info" "udev:/sys/devices/LNXSYSTM:00/device:00/PNP0A08:00/LNXVIDEO:01/input/input15/event15"
[ 43.931] (II) XINPUT: Adding extended input device "Video Bus" (type: KEYBOARD, id 7)
[ 43.931] (**) Option "xkb_rules" "evdev"
[ 43.931] (**) Option "xkb_model" "evdev"
[ 43.931] (**) Option "xkb_layout" "us"
[ 43.932] (II) config/udev: Adding input device Power Button (/dev/input/event4)
[ 43.932] (**) Power Button: Applying InputClass "evdev keyboard catchall"
[ 43.932] (II) Using input driver 'evdev' for 'Power Button'
[ 43.932] (II) Loading /usr/lib/xorg/modules/input/evdev_drv.so
[ 43.932] (**) Power Button: always reports core events
[ 43.932] (**) Power Button: Device: "/dev/input/event4"
[ 43.932] (--) Power Button: Found keys
[ 43.932] (II) Power Button: Configuring as keyboard
[ 43.932] (**) Option "config_info" "udev:/sys/devices/LNXSYSTM:00/device:00/PNP0C0C:00/input/input4/event4"
[ 43.932] (II) XINPUT: Adding extended input device "Power Button" (type: KEYBOARD, id 8)
[ 43.932] (**) Option "xkb_rules" "evdev"
[ 43.932] (**) Option "xkb_model" "evdev"
[ 43.932] (**) Option "xkb_layout" "us"
[ 43.932] (II) config/udev: Adding input device Lid Switch (/dev/input/event5)
[ 43.932] (II) No input driver/identifier specified (ignoring)
[ 43.932] (II) config/udev: Adding input device Sleep Button (/dev/input/event6)
[ 43.932] (**) Sleep Button: Applying InputClass "evdev keyboard catchall"
[ 43.932] (II) Using input driver 'evdev' for 'Sleep Button'
[ 43.932] (II) Loading /usr/lib/xorg/modules/input/evdev_drv.so
[ 43.932] (**) Sleep Button: always reports core events
[ 43.932] (**) Sleep Button: Device: "/dev/input/event6"
[ 43.932] (--) Sleep Button: Found keys
[ 43.932] (II) Sleep Button: Configuring as keyboard
[ 43.932] (**) Option "config_info" "udev:/sys/devices/LNXSYSTM:00/device:00/PNP0C0E:00/input/input6/event6"
[ 43.932] (II) XINPUT: Adding extended input device "Sleep Button" (type: KEYBOARD, id 9)
[ 43.933] (**) Option "xkb_rules" "evdev"
[ 43.933] (**) Option "xkb_model" "evdev"
[ 43.933] (**) Option "xkb_layout" "us"
[ 43.933] (II) config/udev: Adding input device HID 413c:8161 (/dev/input/event2)
[ 43.933] (**) HID 413c:8161: Applying InputClass "evdev keyboard catchall"
[ 43.933] (II) Using input driver 'evdev' for 'HID 413c:8161'
[ 43.933] (II) Loading /usr/lib/xorg/modules/input/evdev_drv.so
[ 43.933] (**) HID 413c:8161: always reports core events
[ 43.933] (**) HID 413c:8161: Device: "/dev/input/event2"
[ 43.933] (--) HID 413c:8161: Found keys
[ 43.933] (II) HID 413c:8161: Configuring as keyboard
[ 43.933] (**) Option "config_info" "udev:/sys/devices/pci0000:00/0000:00:1a.0/usb1/1-1/1-1.2/1-1.2.1/1-1.2.1:1.0/input/input2/event2"
[ 43.933] (II) XINPUT: Adding extended input device "HID 413c:8161" (type: KEYBOARD, id 10)
[ 43.933] (**) Option "xkb_rules" "evdev"
[ 43.933] (**) Option "xkb_model" "evdev"
[ 43.933] (**) Option "xkb_layout" "us"
[ 43.934] (II) config/udev: Adding input device HID 413c:8162 (/dev/input/event3)
[ 43.934] (**) HID 413c:8162: Applying InputClass "evdev pointer catchall"
[ 43.934] (II) Using input driver 'evdev' for 'HID 413c:8162'
[ 43.934] (II) Loading /usr/lib/xorg/modules/input/evdev_drv.so
[ 43.934] (**) HID 413c:8162: always reports core events
[ 43.934] (**) HID 413c:8162: Device: "/dev/input/event3"
[ 43.934] (--) HID 413c:8162: Found 3 mouse buttons
[ 43.934] (--) HID 413c:8162: Found relative axes
[ 43.934] (--) HID 413c:8162: Found x and y relative axes
[ 43.934] (II) HID 413c:8162: Configuring as mouse
[ 43.934] (**) HID 413c:8162: YAxisMapping: buttons 4 and 5
[ 43.934] (**) HID 413c:8162: EmulateWheelButton: 4, EmulateWheelInertia: 10, EmulateWheelTimeout: 200
[ 43.934] (**) Option "config_info" "udev:/sys/devices/pci0000:00/0000:00:1a.0/usb1/1-1/1-1.2/1-1.2.2/1-1.2.2:1.0/input/input3/event3"
[ 43.934] (II) XINPUT: Adding extended input device "HID 413c:8162" (type: MOUSE, id 11)
[ 43.934] (II) HID 413c:8162: initialized for relative axes.
[ 43.934] (**) HID 413c:8162: (accel) keeping acceleration scheme 1
[ 43.934] (**) HID 413c:8162: (accel) acceleration profile 0
[ 43.934] (**) HID 413c:8162: (accel) acceleration factor: 2.000
[ 43.934] (**) HID 413c:8162: (accel) acceleration threshold: 4
[ 43.934] (II) config/udev: Adding input device HID 413c:8162 (/dev/input/mouse1)
[ 43.934] (II) No input driver/identifier specified (ignoring)
[ 43.934] (II) config/udev: Adding input device Laptop_Integrated_Webcam_0.3M (/dev/input/event10)
[ 43.934] (**) Laptop_Integrated_Webcam_0.3M: Applying InputClass "evdev keyboard catchall"
[ 43.934] (II) Using input driver 'evdev' for 'Laptop_Integrated_Webcam_0.3M'
[ 43.934] (II) Loading /usr/lib/xorg/modules/input/evdev_drv.so
[ 43.934] (**) Laptop_Integrated_Webcam_0.3M: always reports core events
[ 43.934] (**) Laptop_Integrated_Webcam_0.3M: Device: "/dev/input/event10"
[ 43.934] (--) Laptop_Integrated_Webcam_0.3M: Found keys
[ 43.934] (II) Laptop_Integrated_Webcam_0.3M: Configuring as keyboard
[ 43.934] (**) Option "config_info" "udev:/sys/devices/pci0000:00/0000:00:1a.0/usb1/1-1/1-1.4/1-1.4:1.0/input/input10/event10"
[ 43.934] (II) XINPUT: Adding extended input device "Laptop_Integrated_Webcam_0.3M" (type: KEYBOARD, id 12)
[ 43.934] (**) Option "xkb_rules" "evdev"
[ 43.934] (**) Option "xkb_model" "evdev"
[ 43.934] (**) Option "xkb_layout" "us"
[ 43.935] (II) config/udev: Adding input device HDA Digital PCBeep (/dev/input/event11)
[ 43.935] (II) No input driver/identifier specified (ignoring)
[ 43.935] (II) config/udev: Adding input device HDA Intel Mic at Ext Right Jack (/dev/input/event12)
[ 43.935] (II) No input driver/identifier specified (ignoring)
[ 43.935] (II) config/udev: Adding input device HDA Intel HP Out at Ext Right Jack (/dev/input/event13)
[ 43.935] (II) No input driver/identifier specified (ignoring)
[ 43.935] (II) config/udev: Adding input device USB OPTICAL MOUSE (/dev/input/event1)
[ 43.935] (**) USB OPTICAL MOUSE: Applying InputClass "evdev pointer catchall"
[ 43.935] (II) Using input driver 'evdev' for ' USB OPTICAL MOUSE'
[ 43.935] (II) Loading /usr/lib/xorg/modules/input/evdev_drv.so
[ 43.936] (**) USB OPTICAL MOUSE: always reports core events
[ 43.936] (**) USB OPTICAL MOUSE: Device: "/dev/input/event1"
[ 43.936] (--) USB OPTICAL MOUSE: Found 3 mouse buttons
[ 43.936] (--) USB OPTICAL MOUSE: Found scroll wheel(s)
[ 43.936] (--) USB OPTICAL MOUSE: Found relative axes
[ 43.936] (--) USB OPTICAL MOUSE: Found x and y relative axes
[ 43.936] (II) USB OPTICAL MOUSE: Configuring as mouse
[ 43.936] (II) USB OPTICAL MOUSE: Adding scrollwheel support
[ 43.936] (**) USB OPTICAL MOUSE: YAxisMapping: buttons 4 and 5
[ 43.936] (**) USB OPTICAL MOUSE: EmulateWheelButton: 4, EmulateWheelInertia: 10, EmulateWheelTimeout: 200
[ 43.936] (**) Option "config_info" "udev:/sys/devices/pci0000:00/0000:00:1d.0/usb2/2-1/2-1.1/2-1.1:1.0/input/input1/event1"
[ 43.936] (II) XINPUT: Adding extended input device " USB OPTICAL MOUSE" (type: MOUSE, id 13)
[ 43.936] (II) USB OPTICAL MOUSE: initialized for relative axes.
[ 43.936] (**) USB OPTICAL MOUSE: (accel) keeping acceleration scheme 1
[ 43.936] (**) USB OPTICAL MOUSE: (accel) acceleration profile 0
[ 43.936] (**) USB OPTICAL MOUSE: (accel) acceleration factor: 2.000
[ 43.936] (**) USB OPTICAL MOUSE: (accel) acceleration threshold: 4
[ 43.936] (II) config/udev: Adding input device USB OPTICAL MOUSE (/dev/input/mouse0)
[ 43.936] (II) No input driver/identifier specified (ignoring)
[ 43.936] (II) config/udev: Adding input device AT Translated Set 2 keyboard (/dev/input/event0)
[ 43.936] (**) AT Translated Set 2 keyboard: Applying InputClass "evdev keyboard catchall"
[ 43.936] (II) Using input driver 'evdev' for 'AT Translated Set 2 keyboard'
[ 43.936] (II) Loading /usr/lib/xorg/modules/input/evdev_drv.so
[ 43.936] (**) AT Translated Set 2 keyboard: always reports core events
[ 43.936] (**) AT Translated Set 2 keyboard: Device: "/dev/input/event0"
[ 43.936] (--) AT Translated Set 2 keyboard: Found keys
[ 43.936] (II) AT Translated Set 2 keyboard: Configuring as keyboard
[ 43.936] (**) Option "config_info" "udev:/sys/devices/platform/i8042/serio0/input/input0/event0"
[ 43.936] (II) XINPUT: Adding extended input device "AT Translated Set 2 keyboard" (type: KEYBOARD, id 14)
[ 43.936] (**) Option "xkb_rules" "evdev"
[ 43.936] (**) Option "xkb_model" "evdev"
[ 43.936] (**) Option "xkb_layout" "us"
[ 43.937] (II) config/udev: Adding input device PS/2 Generic Mouse (/dev/input/event14)
[ 43.937] (**) PS/2 Generic Mouse: Applying InputClass "evdev pointer catchall"
[ 43.937] (II) Using input driver 'evdev' for 'PS/2 Generic Mouse'
[ 43.937] (II) Loading /usr/lib/xorg/modules/input/evdev_drv.so
[ 43.937] (**) PS/2 Generic Mouse: always reports core events
[ 43.937] (**) PS/2 Generic Mouse: Device: "/dev/input/event14"
[ 43.937] (--) PS/2 Generic Mouse: Found 3 mouse buttons
[ 43.937] (--) PS/2 Generic Mouse: Found relative axes
[ 43.937] (--) PS/2 Generic Mouse: Found x and y relative axes
[ 43.937] (II) PS/2 Generic Mouse: Configuring as mouse
[ 43.937] (**) PS/2 Generic Mouse: YAxisMapping: buttons 4 and 5
[ 43.937] (**) PS/2 Generic Mouse: EmulateWheelButton: 4, EmulateWheelInertia: 10, EmulateWheelTimeout: 200
[ 43.937] (**) Option "config_info" "udev:/sys/devices/platform/i8042/serio1/input/input14/event14"
[ 43.937] (II) XINPUT: Adding extended input device "PS/2 Generic Mouse" (type: MOUSE, id 15)
[ 43.937] (II) PS/2 Generic Mouse: initialized for relative axes.
[ 43.937] (**) PS/2 Generic Mouse: (accel) keeping acceleration scheme 1
[ 43.937] (**) PS/2 Generic Mouse: (accel) acceleration profile 0
[ 43.937] (**) PS/2 Generic Mouse: (accel) acceleration factor: 2.000
[ 43.937] (**) PS/2 Generic Mouse: (accel) acceleration threshold: 4
[ 43.937] (II) config/udev: Adding input device PS/2 Generic Mouse (/dev/input/mouse2)
[ 43.937] (II) No input driver/identifier specified (ignoring)
[ 43.937] (II) config/udev: Adding input device PC Speaker (/dev/input/event8)
[ 43.937] (II) No input driver/identifier specified (ignoring)
[ 43.938] (II) config/udev: Adding input device Dell WMI hotkeys (/dev/input/event9)
[ 43.938] (**) Dell WMI hotkeys: Applying InputClass "evdev keyboard catchall"
[ 43.938] (II) Using input driver 'evdev' for 'Dell WMI hotkeys'
[ 43.938] (II) Loading /usr/lib/xorg/modules/input/evdev_drv.so
[ 43.938] (**) Dell WMI hotkeys: always reports core events
[ 43.938] (**) Dell WMI hotkeys: Device: "/dev/input/event9"
[ 43.938] (--) Dell WMI hotkeys: Found keys
[ 43.938] (II) Dell WMI hotkeys: Configuring as keyboard
[ 43.938] (**) Option "config_info" "udev:/sys/devices/virtual/input/input9/event9"
[ 43.938] (II) XINPUT: Adding extended input device "Dell WMI hotkeys" (type: KEYBOARD, id 16)
[ 43.938] (**) Option "xkb_rules" "evdev"
[ 43.938] (**) Option "xkb_model" "evdev"
[ 43.938] (**) Option "xkb_layout" "us"
[ 48.392] (II) intel(0): EDID vendor "BOE", prod id 1422
[ 48.392] (II) intel(0): Printing DDC gathered Modelines:
[ 48.392] (II) intel(0): Modeline "1366x768"x0.0 72.33 1366 1414 1446 1526 768 771 777 790 +hsync -vsync (47.4 kHz)
[ 48.456] (WW) EDID timing clock 85.75 exceeds claimed max 85MHz, fixing
[ 48.457] (II) intel(0): EDID vendor "BOE", prod id 1422
[ 48.457] (II) intel(0): Printing DDC gathered Modelines:
[ 48.457] (II) intel(0): Modeline "1366x768"x0.0 72.33 1366 1414 1446 1526 768 771 777 790 +hsync -vsync (47.4 kHz)
[ 48.517] (WW) EDID timing clock 85.75 exceeds claimed max 85MHz, fixing
[ 49.976] (II) intel(0): EDID vendor "BOE", prod id 1422
[ 49.976] (II) intel(0): Printing DDC gathered Modelines:
[ 49.976] (II) intel(0): Modeline "1366x768"x0.0 72.33 1366 1414 1446 1526 768 771 777 790 +hsync -vsync (47.4 kHz)
[ 50.035] (WW) EDID timing clock 85.75 exceeds claimed max 85MHz, fixing
[ 213.440] (II) config/udev: removing device USB OPTICAL MOUSE
[ 213.440] (II) USB OPTICAL MOUSE: Close
[ 213.440] (II) UnloadModule: "evdev"
[ 213.440] (II) Unloading evdev
[ 213.728] (II) config/udev: Adding input device USB OPTICAL MOUSE (/dev/input/event1)
[ 213.728] (**) USB OPTICAL MOUSE: Applying InputClass "evdev pointer catchall"
[ 213.728] (II) Using input driver 'evdev' for ' USB OPTICAL MOUSE'
[ 213.728] (II) Loading /usr/lib/xorg/modules/input/evdev_drv.so
[ 213.728] (**) USB OPTICAL MOUSE: always reports core events
[ 213.728] (**) USB OPTICAL MOUSE: Device: "/dev/input/event1"
[ 213.728] (--) USB OPTICAL MOUSE: Found 3 mouse buttons
[ 213.728] (--) USB OPTICAL MOUSE: Found scroll wheel(s)
[ 213.728] (--) USB OPTICAL MOUSE: Found relative axes
[ 213.728] (--) USB OPTICAL MOUSE: Found x and y relative axes
[ 213.728] (II) USB OPTICAL MOUSE: Configuring as mouse
[ 213.728] (II) USB OPTICAL MOUSE: Adding scrollwheel support
[ 213.728] (**) USB OPTICAL MOUSE: YAxisMapping: buttons 4 and 5
[ 213.728] (**) USB OPTICAL MOUSE: EmulateWheelButton: 4, EmulateWheelInertia: 10, EmulateWheelTimeout: 200
[ 213.728] (**) Option "config_info" "udev:/sys/devices/pci0000:00/0000:00:1d.0/usb2/2-1/2-1.1/2-1.1:1.0/input/input16/event1"
[ 213.728] (II) XINPUT: Adding extended input device " USB OPTICAL MOUSE" (type: MOUSE, id 13)
[ 213.728] (II) USB OPTICAL MOUSE: initialized for relative axes.
[ 213.728] (**) USB OPTICAL MOUSE: (accel) keeping acceleration scheme 1
[ 213.728] (**) USB OPTICAL MOUSE: (accel) acceleration profile 0
[ 213.728] (**) USB OPTICAL MOUSE: (accel) acceleration factor: 2.000
[ 213.728] (**) USB OPTICAL MOUSE: (accel) acceleration threshold: 4
[ 213.730] (II) config/udev: Adding input device USB OPTICAL MOUSE (/dev/input/mouse0)
[ 213.730] (II) No input driver/identifier specified (ignoring)
[ 1627.253] (II) intel(0): EDID vendor "BOE", prod id 1422
[ 1627.253] (II) intel(0): Printing DDC gathered Modelines:
[ 1627.253] (II) intel(0): Modeline "1366x768"x0.0 72.33 1366 1414 1446 1526 768 771 777 790 +hsync -vsync (47.4 kHz)
[ 1627.311] (WW) EDID timing clock 85.75 exceeds claimed max 85MHz, fixing
[ 1644.964] (II) intel(0): EDID vendor "BOE", prod id 1422
[ 1644.964] (II) intel(0): Printing DDC gathered Modelines:
[ 1644.964] (II) intel(0): Modeline "1366x768"x0.0 72.33 1366 1414 1446 1526 768 771 777 790 +hsync -vsync (47.4 kHz)
[ 1645.027] (WW) EDID timing clock 85.75 exceeds claimed max 85MHz, fixing
[ 1645.042] (II) intel(0): Allocated new frame buffer 2752x768 stride 11264, tiled
[ 1645.230] (II) intel(0): EDID vendor "BOE", prod id 1422
[ 1645.230] (II) intel(0): Printing DDC gathered Modelines:
[ 1645.230] (II) intel(0): Modeline "1366x768"x0.0 72.33 1366 1414 1446 1526 768 771 777 790 +hsync -vsync (47.4 kHz)
[ 1645.289] (WW) EDID timing clock 85.75 exceeds claimed max 85MHz, fixing
[ 1645.307] (II) intel(0): EDID vendor "BOE", prod id 1422
[ 1645.307] (II) intel(0): Printing DDC gathered Modelines:
[ 1645.307] (II) intel(0): Modeline "1366x768"x0.0 72.33 1366 1414 1446 1526 768 771 777 790 +hsync -vsync (47.4 kHz)
[ 1645.365] (WW) EDID timing clock 85.75 exceeds claimed max 85MHz, fixing
[ 1645.387] (II) intel(0): EDID vendor "BOE", prod id 1422
[ 1645.387] (II) intel(0): Printing DDC gathered Modelines:
[ 1645.387] (II) intel(0): Modeline "1366x768"x0.0 72.33 1366 1414 1446 1526 768 771 777 790 +hsync -vsync (47.4 kHz)
[ 1645.446] (WW) EDID timing clock 85.75 exceeds claimed max 85MHz, fixing
[ 1645.447] (II) intel(0): EDID vendor "BOE", prod id 1422
[ 1645.447] (II) intel(0): Printing DDC gathered Modelines:
[ 1645.447] (II) intel(0): Modeline "1366x768"x0.0 72.33 1366 1414 1446 1526 768 771 777 790 +hsync -vsync (47.4 kHz)
[ 1645.505] (WW) EDID timing clock 85.75 exceeds claimed max 85MHz, fixing
[ 2335.972] (II) intel(0): EDID vendor "BOE", prod id 1422
[ 2335.972] (II) intel(0): Printing DDC gathered Modelines:
[ 2335.972] (II) intel(0): Modeline "1366x768"x0.0 72.33 1366 1414 1446 1526 768 771 777 790 +hsync -vsync (47.4 kHz)
[ 2336.030] (WW) EDID timing clock 85.75 exceeds claimed max 85MHz, fixing
lspci output
00:00.0 Host bridge: Intel Corporation Core Processor DRAM Controller (rev 02)
00:02.0 VGA compatible controller: Intel Corporation Core Processor Integrated Graphics Controller (rev 02)
00:16.0 Communication controller: Intel Corporation 5 Series/3400 Series Chipset HECI Controller (rev 06)
00:1a.0 USB controller: Intel Corporation 5 Series/3400 Series Chipset USB2 Enhanced Host Controller (rev 05)
00:1b.0 Audio device: Intel Corporation 5 Series/3400 Series Chipset High Definition Audio (rev 05)
00:1c.0 PCI bridge: Intel Corporation 5 Series/3400 Series Chipset PCI Express Root Port 1 (rev 05)
00:1c.1 PCI bridge: Intel Corporation 5 Series/3400 Series Chipset PCI Express Root Port 2 (rev 05)
00:1c.2 PCI bridge: Intel Corporation 5 Series/3400 Series Chipset PCI Express Root Port 3 (rev 05)
00:1c.4 PCI bridge: Intel Corporation 5 Series/3400 Series Chipset PCI Express Root Port 5 (rev 05)
00:1d.0 USB controller: Intel Corporation 5 Series/3400 Series Chipset USB2 Enhanced Host Controller (rev 05)
00:1e.0 PCI bridge: Intel Corporation 82801 Mobile PCI Bridge (rev a5)
00:1f.0 ISA bridge: Intel Corporation Mobile 5 Series Chipset LPC Interface Controller (rev 05)
00:1f.2 SATA controller: Intel Corporation 5 Series/3400 Series Chipset 6 port SATA AHCI Controller (rev 05)
00:1f.3 SMBus: Intel Corporation 5 Series/3400 Series Chipset SMBus Controller (rev 05)
00:1f.6 Signal processing controller: Intel Corporation 5 Series/3400 Series Chipset Thermal Subsystem (rev 05)
12:00.0 Network controller: Broadcom Corporation BCM4313 802.11b/g/n Wireless LAN Controller (rev 01)
13:00.0 Ethernet controller: Atheros Communications AR8152 v2.0 Fast Ethernet (rev c1)
ff:00.0 Host bridge: Intel Corporation Core Processor QuickPath Architecture Generic Non-core Registers (rev 02)
ff:00.1 Host bridge: Intel Corporation Core Processor QuickPath Architecture System Address Decoder (rev 02)
ff:02.0 Host bridge: Intel Corporation Core Processor QPI Link 0 (rev 02)
ff:02.1 Host bridge: Intel Corporation Core Processor QPI Physical 0 (rev 02)
ff:02.2 Host bridge: Intel Corporation Core Processor Reserved (rev 02)
ff:02.3 Host bridge: Intel Corporation Core Processor Reserved (rev 02)No one? I have the exact same problem. MSI x360 laptop, intel onboard graphics. I too use xrandr. I've seen elsewhere that windows users have solved this by turning off GPU overclocking. Maybe this can point us in the right direction?
-
I updated to Premiere Pro CC 2014, all the other Adobe CC 2014 software works great, but Premiere doesnt even load. The starting page (frame) comes up - my whole computer slows down and after a minute or two it crashes completely and comes up with the message : "Adobe Premiere Pro could not find any capable video play modules. Please update your video display drivers and start again."
I'm running a macbook Pro 15" (2014) with 16GB RAM and 760GB SSD.
PLEASE HELP!Hi Delarey,
Please go to the following location and rename the folder to old_folder name
User/user library/Application Support and rename Adobe folder
User/user library/Preferences and rename the Adobe folder
Then go to Documents folder and Go to Adobe/Premiere pro/8.0 and rename 8.0 folder
Make sure that you are in user library if you are not sure check the link below.
Access hidden user library files | Mac OS 10.7 and later
Regards,
Vinay -
Suggest Solution for this Display Flickering problem ....
Hi, I read the post about calibration and I probably do that a little too often TBH! As I get so little time out the battery and mainly use my MBP on my lap, usually with the power supply near by, it gets charged to full, run to empty to the point of sleep, or sometimes it even cuts out and then is recharged to full again, so I really think it's new battery time. I've seen non Apple Official ones for between £35 and £65 that have 3 year warranties and state they are around 5200mh but am unsure due to reviews.
Later...
Anyway's I have now ordered a non Apple replacement from Amazon for about £35 and it has several good reviews and 4.5 out of 5 stars so I'll see if it works and report back. If it doesn't I'll send it back and get the Official Apple one.
Message was edited by: Missy Steph -
Thunderbolt display doesn't start after standby
wakeup the MacBook from standby mode the thunderbolt display will not start since the mountain lion update.
you must unplug and replug the connector for starting the displayI had the same problem with my new MacBook Pro Retina connected to a new Thunderbolt Display running OS 10.8.2. I did resolve the problem after a week or so of troubleshooting, but it did involve getting a resplacement display from Apple.
Here WAS my situation: After connecting the display and having things work (video and external keyboard/mouse and sound/video), when the computer went to sleep (not display sleep, computer sleep) or when it was re-started via the display, I had video but did not have any other external control or display sound/video (was as if the internal hub of the TD was not working).
When I disconnected the Thunderbolt connector (which comes from the "All-in-One" TD cable) from the computer and then plugged in a regular Thunderbolt cable to the computer port and the empty TD Thunderbolt port, all was well. In other words I left the TD Thunderbolt connector disconnected and bypassed it with another Thunderbolt cable between the computer and the TD display port. Note that I left the power connector from the "All-in-One" cable connected as there was no problem with that portion.
This, of course meant that the Thunderbolt part of the All-in-One cable (which is not unpluggable from the display) was bad or the display electronics leading to it was bad. Either way it required a new or repaired display.
I hope this is helpful. After bypassing the All-in-One Thunderbolt interface with my workaround above, I never had the problem occur again (you could command the computer to sleep or re-start it from the display, remove the laptop to use elsewhere, re-connect it, etc. and everything continued to work without fiddling with any connections). As a result, I had Apple replace the display under warranty provisions.
Barry -
I have administrator rights to the computer. The drivers are up to date. But I am still getting the error message "Adobe Premiere Pro could not find any capable video play modules. Please update your video display drivers and start again" when opening Premier Pro CS5.5. This appears to have happed after I upgraded to Mac OS 10.10.2.
Anyone?
ThanksHi Stan.
I had the same problem as you did though I am using Adobe CC. I saw nobody replied to you so perhaps my eventual success on my later version may have applications to the error on your version.
Anyhow, I did all the suggestions found here (Error "Premiere Pro could not find any capable video play modules" | Startup ) first and updated my NVidea card to no avail. Eventually what did the trick was this...
After mucking about with the video card, I said "OK lets just have a go at Premiere itself." So I uninstalled Premiere CC and reinstalled it. Now for some reason it didn't give me the latest patch but a slightly earlier version than the current one but lo and behold it was fine with the video card again. I was able to get my friend's video imported and quickly edited but then was having some issues with exporting where it would hang up but I went into Adobe Media Encoder and exported it there without a care. That task out of the way, I then went and made the update to the latest patch and it works perfectly fine - no video driver issues.
So short of it is this - if you've updated your drivers, perhaps what you could try uninstalling and reinstalling Premiere.
Let me know if this works.
Cheers and good luck -
My Macbook Pro display flickers when using power adapter
I purchased a new power adapter for my Macbook Pro (late 2011 17 inch) from Other World Computing and now the display flickers intermittently when attached to the new power adapter. There is no flickering when not attached to the power adapter or when attached to the old power adapter.
Any ideas on fixing the new power adapter? I would rather fix the problem if it is simple.
Thanks for the help.
Roy PatienceIt doesn't affect the battery. You can use your MacBook Pro plugged in all the time without damaging the battery. You only have to be sure that you unplug it and run a battery cycle (drain the battery without letting the Mac turn off and charge it fully) at least once a month to keep the battery life.
If you want more information about your battery > http://www.apple.com/batteries/notebooks.html -
What is the solution for display flickering for macbook pro??
What is the solution for display flickering for macbook pro??
i have a macbook pro 13.3 late 2013 model, i was using it suddenly the screen went black out and came again it happened for around 15 mints
then i went blackout for a long time then after 3 hours it suddenly again the screen displayed properly for 4 hours, again it went black out. please give me a solution regarding this.Reset PRAM: http://support.apple.com/kb/PH14222
Reset SMC. http://support.apple.com/kb/HT3964
Choose the appropriate method.
"Resetting SMC on portables with a battery you should not remove on your own". -
PB G4 15" Display flickers then dies
Hello - I'm sure this has been covered before but the problem I'm having is the display flickers (after opening the PowerBook) then goes completely dim. I can still see the desktop functioning but just barely so I'm assuming that it's the display bulb.
I've been using an external display for a good time now and want my "lap" top back. Has anyone had experience replacing this bulb and/or just replacing the whole display? Which do you recommend?
I appreciate the feedback... thank you.Yeah now that I look around a little more, PowerbookMedic agrees that it's likely the inverter. http://www.powerbookmedic.com/xcart1/product.php?productid=16612 Has anyone had experience with PowerbookMedic?
More importantly, can someone point me to an in-depth tutorial on replacing the Inverter yourself? Thanks -
MacBook Pro "Retina display flickering"
MacBook Pro retina display flickering, the Genius Bar says they can't fix it, that this is normal. Is this true?
I have no idea why you are posting this on adobe business catalyst.
This is not the place for this.
This is Adobe, Not Apple, They are not the same company.
But as a note, its to do with the latest release of Adobe Flash. -
Regarding to Display Flickering
Well, as a lot of people I'm one of those who have suffered the disturbing and scary display flickering. It was more frustrating since it begun after the 1st. year and I don't have AppleCare. Well I don't know if this solution works for everybody but at least for me it was magic. Before this I tried every hardware/firmware reset solution but nothing works. Also I have read of people who had their inverters replaced (for me it looks like a Logic Board replacement) and some with good results and others... well, not so good.
The think I did was simply erase the ~/Library/Preferences and never had those flickerings anymore. Maybe something gets corrupt there but by now I have a lot of days without even a little dim, perhaps in the Preferences is where the brightness setting file is located and it gets corrupt, I don't know but it worked, so maybe that's your solution too. Note: remember, if you delete the Preferences folder a lot of your preferences in the Finder, Dock, Dashboard and System Preferences will be back to factory defaults (or system defaults), but no personal or important files are deleted. The OSX in your next login/reboot will generate the folder again automatically.
Good Luck!fredericlang:
I'm glad it worked for you!.
I deeply checked the Preferences folder and as I see the folder ByHost contains the screensaver and system preferences files and also other named HIToolbox but I don't know what is that for. I think the screensaver or system preferences are the ones who do the mess, so if this flicker comes again I'll try just deleting those to check.
Martin1301:
I mean ~/Library/Preferences
corband:
I think is just the CD that for some reason doesn't let the system to boot.
Just power up the macbook and with the chime sound press (and keep it pressed) the trackpad button until the CD is ejected.
Maybe you are looking for
-
Apps not being updated probably due to error of same id login in 2 devices . please help.
-
Problem with minut price to Israel
Hi! I have a Subscription to Israel(120minutes) but it dosent work and the minut still coasts about 2,00kr when i call to Israel. What shall I do?
-
Direct & Indirect Breakup after allocation to COPA
Dear All We have an issue with COPA allocations. Allocations happen in two steps. 1. Allocation of indirect cost centers such as head office costs to actual cost centers(branches) 2. Allocation of costs in the real cost center(Branch) to COPA produ
-
Where can i download jam pack 4 (orchestral sounds) for garageband 6.0.5. please. I have an air book maverick OSX 10.9.4. Thanks
-
Sending an username and a password with SSL but without Authentication
Hi, I've read several threads about this topic but I'm still confused. I need to send a login and a password in a more or less secure way (not sending it in the get/post and not using a base64 encoding), but I don't want authentication, just to send