DNS not working for some computers
We have a SRP521W router and is set up with one SSID for wireless. In our office all the computers (5) can connect but only some may get on the internet. I have a laptop I am testing with and it will not connect, wired or wireless.
I found an article relating to flushing DNS, tried that, no luck.
I found another that said I should try setting my DNS to 208.67.222.222 and this worked, internet works fine.
I tried rebooting the DSL modem and router, tried many different things but am not a networking guru so I am just not sure why the DNS is not working for one computer but works for another, connected to same LAN or SSID.
Thanks,
Brad
Though what Don posted is one way to accomplish it, I never add anything to my DNS and it works fine. Windows DNS, in a default installation, will automatically forward to the root (.com, .edu, .gov, etc.). So I always just point my workstations
to my Domain Controller as their DNS and everything works just fine without any additional configuration.
Guess I'm one of those who won't even trust Google for sharing a DNS, particularly when I have never needed to set up any forwarders.
.:|:.:|:. tim
Similar Messages
-
Outlook autodiscover is not working for some users in coexistence
Hi
We are doing exchnage 2013/2010 coexistence
Most everything is ok BUT outlook autodiscover is not working for some exchange 2010 users now that 2013 is in the front!!!. We end up creating the profiles manually. It has affected some but not all the users.
I followed the instructions here but it didn't help.
http://blogs.technet.com/b/tips_from_the_inside/archive/2012/01/11/autodiscover-fails-for-one-or-more-users.aspx
Using outlook 2010, 2013, patches, .... didn't make a difference
Would you please help?
Thank youHi
If it is affecting only few handful of users i could suspect a mailbox corruption and would recommend to move mailbox and see the results.
Also you can try below
You need to set the values MaxFieldLength, MaxRequestBytes & MaxTokenSize to below on Exchange 2010 CAS servers as well as Exchange 2013 CAS servers
Path: HKEY_LOCAL_MACHINE\System\CurrentControlSet\Services\HTTP\Parameters
Name: MaxFieldLength
Type: DWORD
Value: 65534
Path: HKEY_LOCAL_MACHINE\System\CurrentControlSet\Services\HTTP\Parameters
Name: MaxRequestBytes
Type: DWORD
Value: 16777216
Path: HKEY_LOCAL_MACHINE\SYSTEM\CurrentControlSet\Control\Lsa\Kerberos\Parameters
Name: MaxTokenSize
Type: REG_DWORD
Value: 48000
Just reboot the servers once its done and you will be good to go.
References
https://social.technet.microsoft.com/Forums/en-US/cc2929ac-4d36-4e84-a567-ce9b3bec1398/http-400-bad-request-on-iis-8-exchange-2013-cu2-on-windows-server-2012-autodiscovery-is-not?forum=exchangesvrgeneral
http://blogs.technet.com/b/kristinw/archive/2013/03/28/recommended-changes-and-enhancements-to-support-exchange-in-an-enterprise-environment-whew.aspx
Remember to mark as helpful if you find my contribution useful or as an answer if it does answer your question.That will encourage me - and others - to take time out to help you Check out my latest blog posts on http://exchangequery.com Thanks Sathish
(MVP) -
MAM application is not working for some users
Hi All,
Tha MAM application is not working for some users.Different users have different workcenters other than that I dont see any other change. When I run MAM30_090_GETLIST in the backend I can see the no of customized users.But I cant see same no of users in the MEREP_207 table for the Syncbo MAM30_090 and strcture id TOP in the middleware. There is a data when I checked under worklist monitor for that user. But neither the MAM application nor MAM data is downloading to that device.
If I use different user on the same device I can see the MAM application and MAM data.
What could be the wrong in this case. Any help would be highly appreciated.
Mobile Client:MI 70 SP 15 Patch 0 Build 200802280918
Middleware:SAP NetWeaver 2004s with Patch leve 15
Backend:SAP ECC 6.0
Application:MAM 3.0
Thanks and Regards,
Ameer.Hi,
from your description the source of your issue is quite obvious: some of the MAM users configured in spro are not configured properly.
For T01 SyncBos the number of TOP records in merep_207 MUST be the same as number of headers returned by an appropriate getList FM in the backend.
You need to solve this before you can go any further.
Reason why a record is not recorded in MEREP_207 - getdetail failed for whatever reason. So execute MAM30_ML_getdetail for each of the users that is not replicated in the middleware and check if there are errors in RETURN table. If there is no error - one of the common reason for replication fail is when there are records in item tables that have duplicate primary keys.
Regards,
Larissa Limarova -
In Robohelp 9, search does not work for some Vietnamese characters.
In Robohelp 9, search does not work for some Vietnamese characters.
I don't think there is anything we can do on a user to user forum. I suggest you report this to Adobe as a bug. Please follow this link.
http://www.Adobe.com/cfusion/mmform/index.cfm?name=wishform&product=38
If you need a more immediate response, you would need to take that up with Adobe support.
See www.grainge.org for RoboHelp and Authoring tips
@petergrainge -
Software Update Point Switching is not working for some Clients
Hi there,
I found nothing similar here and I hope this is the right section.
I´m running ConfigMgr 2012 R2 where one of the Site Systems from one of the Primaries is located in an untrusted Forest in a perimeter Network. The Site System there has the MP, SUP and DB Roles. In general it works great. The Systems in that untrusted Forest
get the SCCM Agent pushed, see and can install published Software packages and receive Windows Updates. But there are a few systems where everything works, except Windows Updates.
So I had a deeper look at what is happening and found out that the SUP switching is not working for them. They always try to contact the SUP from the Primary, which they cannot reach (this is intended).
From how I understand SUP switching as described here
http://blogs.technet.com/b/configmgrteam/archive/2013/03/27/software-update-points-in-cm2012sp1.aspx#pi140062=1
the Windows Update Agent tries to connect to a SUP every 30 minutes and after 4 failed attempts he will try to connect to the next one until he finds one which works.
As I said before, this seems to work for most systems in the untrusted forest, but some do not make any intentions to switch the SUP.
So my next step was to find out from where the Update Agent can get the information of the available SUPs. I think they either don´t receive the information that other SUPs exist, or if the Information is there, they don´t realize that there´s an error and
make no attempt to switch.
I used the System Center Support Center to gather all Information from some of the systems with that problems (Log Files, WMI information, registry information, policies etc.) but I cannot find where SCCM or the Update Agent store the information which SUPs
are available in my environment.
I´m sure the problem is on the Systems which fail to connect to the right SUP and not in the SCCM infrastructure itself, because for most of the systems everything is working just perfect. Unfortunately in the Blog Post above there´s also no information
where this information is stored and how it is obtained by the clients. In the comments there´s even one post which describes the same problem I have here, but there was no answer. I hope someone can point me into the right direction, because I´m stuck currently.
Things I tried additionally to all the log file / WMI / registry sniffing:
Removing the Software Distribution Folder and restarting the Windows Update Agent
Removing the WindowsUpdate Registry folder in the HKLM\SOFTWARE\Policies\Windows section in the Registry and restarting the Windows Update Agent.
Tried to reset the WUAgent with wuauclt /Resetauthorization additionally to the steps above.
I also tried to manually set the WUServer and WUStatusServer Keys in the registry to the new Server, but as soon as the next Update Scan cycle runs, the value is set back to the URL of the Primary Sites SUP
Is someone having additional ideas? It seems to me older systems are more affected (which were configured for a standard WSUS before SCCM 2012 was deployed) than newer ones which were installed when SCCM was in place already. But I don´t know what else to
"reset" on those machines without reinstalling them.Thank you very much for your response. I must have missed that one by looking through numerous Logfiles. In this, there´s indeed a list of all available SUPs. So according to the LocationServices.log the machine should have a choice.
The WMI Key however, contains just one entry and this is the URL of the Primaries SUP which is not reachable in the untrusted forest. Is it OK that the WMI entry includes only one entry? If yes, what process is putting the results from the LocationServices
into WMI? It seems like the Windows Update Agent is feeded from the WMI Key then. If this is the case my problems seems to be the "communication path" between these two components.
Is this the job from the SCCM Agent, the Windows Update Agent or maybe some third component I´m not aware of? I wonder how I can fix this. -
Wake on Demand: Not working for some services, others OK
I haven't been able to figure this problem out... Wake on Demand for a previous generation Mac mini running Snow Leopard 10.6.8 works for things like a CrashPlan automated backup but does not work for things like remote SSH login or Screen Sharing. In all cases, the services are being originated on a latest generation iMac running Mac OS X Lion (10.7.2).
While it's not an earth-shattering event to get off my backside and walk over to the Mac mini across the house to press its Shift key to waken the thing, it gets rather old to have to keep doing so, especially since CrashPlan automated backups are taking place while the Mac mini is otherwise asleep (the sleep indicator is slowly pulsing).
I've been through the Apple tech notes regarding Wake on Demand for Snow Leopard 10.6 and have ensured that AirPort and its network are at the top-most position in their respective lists. Other than that, I'm not sure what else I can do. Wake on Network is enabled in the Snow Leopard Mac mini's network System Preferences and there doesn't seem to be any on/off option in the AirPort Extreme base station (just recently updated to 7.6 firmware).
Any thoughts... hints... suggestions?
One final note: this Mac mini is new as of July 2011; just days before the latest generation of Mac mini came out. It came pre-installed with Snow Leopard and, as soon as the users of this mini find software replacements for the old PPC style applicaitons they're used to using, will be upgraded to Lion. However, I feel a bit unsettled in making the move to Lion if I can't get a Snow Leopard feature to work properly. There's no telling if the Lion upgrade will actually fix this behavior or make it worse.
Thanks in advance.I don't think you can wake on network with a closed lid. Try keeping the lid open and putting the machine to sleep. Does it work?
-
Thunderbird Mission Control Desktop/AutoConfig not working for some users
I have the file: "C:\Program Files (x86)\Mozilla Thunderbird\defaults\pref\custom.js"
It contains:
pref("general.config.obscure_value", 0);
pref("general.config.filename", "TMcustom.cfg");
I have the file: "C:\Program Files (x86)\Mozilla Thunderbird\TMcustom.cfg"
It contains:
var promptService = Components.classes["@mozilla.org/embedcomp/prompt-service;1"]
.getService(Components.interfaces.nsIPromptService);
promptService.alert(null, "title", "testing");
For most of my users the alert pops up fine when I start Thunderbird, but for a few it doesn't. All of the machines where setup with the same install script. If I log into one of the machines where it's not working as a different user, then it works fine, so I know the files are in the right spot. So why would it not work for specific users? Is there something in the user's Windows profile that could cause it to not work? Or are there any other suggestions?As it turns out this was a known bug that was corrected in the recent release of Java 7_65 and Java 8_11. Here is a link to the bug description in the database.
Bug ID: JDK-8019274 RMI thread can no longer call out to AWT thread for webstart app -
After Upgradation BPF is not working for some users
Hi All,
We have recently upgraded from BPC 5.1 to 7MS SP7. we are having multi server setup with one application / reporting server (windows 2003 and one sql server 2008 (windows 2003 64 bit).
Intially before upgradation we don't have any issues with BPF and it worked fine for all users. But post upgradation tasks within the BPF does not work for other users except for the first two people who first used it. Other users have the same rights as the ones who can access the tasks.
when they click on the link it gets them to eExcel and the right application but doesnt open the package or report assigned to the task. It doesn't give us any errors, on the status bar we get a message finalising but does not getting any thing.
Any inputs ??Hi,
Are you sure that those users have installed BPC 7 SP7 clients on their machine? Meaning that you uninstalled 5.1 clients and installed the new client from http://servername/Osoft?
If yes, you should maybe run a client diagnostic on the machines and also check the Management Console for any error messages.
Hope this will drive you to a potential solution.
Best Regards,
Patrick -
Outlook Anywhere not working for some users
Hi All,
I am having a strange issue today with a customer -
Outlook Anywhere has been enabled on their Exchange 2010 environment, but it doesn't work for some users.
Using the ExRCA I have been able to identify the following error on the users who are unable to connect:
"Testing the MAPI Mail Store endpoint on the Exchange server."
"Attempting to log on to the mailbox"
Mailbox logon returned ecLoginPerm 1010. You don't have the correct permissions to log in to the mailbox.
EMSMDB Status: ecLoginPerm 1010
Elapsed Time: 225 ms.
On users that are able to connect it goes through the ExRCA without any issues.
Any help would be much appreciated.
Cheers,
Jack
Testing the MAPI Mail Store endpoint on the Exchange server.
An error occurred while testing the Mail Store.
Additional Details
Elapsed Time: 333 ms.
Test Steps
Attempting to ping the MAPI Mail Store endpoint with identity: outlook.mg.com:6001.
The endpoint was pinged successfully.
Additional Details
Attempting to log on to the Mailbox.
An error occurred while logging on to the Mailbox.
Additional Details
Mailbox logon returned ecLoginPerm 1010. You don't have the correct permissions to log in to the mailbox.
EMSMDB Status: ecLoginPerm 1010
Elapsed Time: 225 ms.Hi,
I notice that this issue only impact "some users".
I suggest double confirm whether the Outlook Anywhere configuration set correctly on Outlook client. Pic as blow:
Thanks
Mavis Huang
TechNet Community Support -
Corporate connectivity not working for some users
Hi,
I'm having an issue that started about a month ago but is getting worse. A select group of users are no longer able to connect using DirectAccess, even though these users have been using their computers for a few months without issue.
BACKGROUND:
-Windows 2008 R2 DirectAccess server
-Windows 7 x64 enterprise clients
-Most clients experiencing the issue have a newer laptop (Lenovo T440 with Intel 7260AC wireless), but the issue is not limited to this model. Also, I have 25+ other Lenovo T440 units that connect without issue to this day.
TROUBLESHOOTING STEPS:
I have tried disabling the various interfaces used for directaccess on these problem machines and have not been able to narrow it down. Essentially- I've noticed the IP-HTTPS interface shows deactivated, so I'll disable Teredo. This
usually allows the IP-HTTPS to show activated, and connectivity is restored. However, after 30 seconds to a few minutes, connectivity will once again drop. So I'll re-enable teredo (default,client, or enterprise client) and connectivity will kick
on for another brief period, but drops again shortly after.
I have confirmed that during these short periods of connectivity working, the wf.msc shows connectivity using NTLM and Kerberos, but the clients just can't seem to stay connected on any interface.
However, in the wf.msc when the clients are not functioning, I only ever see one NTLM entry.LOGS:
Below is a directaccess client log pulled from a non-functioning client before making any changes or any testing. Feel free to ask for the rest of the log if needed-- I have put in place holders for information that may be sensitive. Thank you!!
RED: Corporate connectivity is not working.
Windows is unable to relocationve corporate network names. Please contact your administrator if this problem persists.
24/3/2015 18:21:43 (UTC)
Probes List
FAIL PING: location-dc.domain.local
FAIL PING: location-file.domain.local
DTE List
PASS PING: 2002:'mac':5a1c::'mac':5a1c
PASS PING: 2002:'mac':5a1d::'mac':5a1d
C:\WINDOWS\system32\LogSpace\{05471C14-7140-4651-84C2-230EC7D70628}>ipconfig /all
Windows IP Configuration
Host Name . . . . . . . . . . . . : c2075
Primary Dns Suffix . . . . . . . : domain.local
Node Type . . . . . . . . . . . . : Hybrid
IP Routing Enabled. . . . . . . . : No
WINS Proxy Enabled. . . . . . . . : No
DNS Suffix Search List. . . . . . : domain.local
domain2.ad
System Quarantine State . . . . . : Not Restricted
Wireless LAN adapter Wireless Network Connection 3:
Media State . . . . . . . . . . . : Media disconnected
Connection-specific DNS Suffix . :
Description . . . . . . . . . . . : Microsoft Virtual WiFi Miniport Adapter #2
Physical Address. . . . . . . . . : 2A-B2-BD-'mac2'-E5
DHCP Enabled. . . . . . . . . . . : Yes
Autoconfiguration Enabled . . . . : Yes
Wireless LAN adapter Wireless Network Connection 2:
Media State . . . . . . . . . . . : Media disconnected
Connection-specific DNS Suffix . :
Description . . . . . . . . . . . : Microsoft Virtual WiFi Miniport Adapter
Physical Address. . . . . . . . . : 2A-B2-BD-'mac2'-E6
DHCP Enabled. . . . . . . . . . . : Yes
Autoconfiguration Enabled . . . . : Yes
Ethernet adapter Bluetooth Network Connection:
Media State . . . . . . . . . . . : Media disconnected
Connection-specific DNS Suffix . :
Description . . . . . . . . . . . : Bluetooth Device (Personal Area Network)
Physical Address. . . . . . . . . : 28-B2-BD-'mac2'-E9
DHCP Enabled. . . . . . . . . . . : Yes
Autoconfiguration Enabled . . . . : Yes
Wireless LAN adapter Wireless Network Connection:
Connection-specific DNS Suffix . : attlocal.net
Description . . . . . . . . . . . : Intel(R) Dual Band Wireless-AC 7260
Physical Address. . . . . . . . . : 28-B2-BD-'mac2'-E5
DHCP Enabled. . . . . . . . . . . : Yes
Autoconfiguration Enabled . . . . : Yes
IPv6 Address. . . . . . . . . . . : 2602:304:'mac3':d370:5a1:c77:834:86a9(Preferred)
Temporary IPv6 Address. . . . . . : 2602:304:'mac3':d370:f9ce:db89:87ad:'mac4'(Preferred)
Link-local IPv6 Address . . . . . : fe80::5a1:c77:834:86a9%12(Preferred)
IPv4 Address. . . . . . . . . . . : 192.168.1.86(Preferred)
Subnet Mask . . . . . . . . . . . : 255.255.255.0
Lease Obtained. . . . . . . . . . : Tuesday, March 24, 2015 1:48:21 PM
Lease Expires . . . . . . . . . . : Wednesday, March 25, 2015 1:48:21 PM
Default Gateway . . . . . . . . . : fe80::21b:5bff:febf:4f21%12
192.168.1.254
DHCP Server . . . . . . . . . . . : 192.168.1.254
DNS Servers . . . . . . . . . . . : 192.168.1.254
NetBIOS over Tcpip. . . . . . . . : Enabled
Ethernet adapter Local Area Connection:
Media State . . . . . . . . . . . : Media disconnected
Connection-specific DNS Suffix . : domain.local
Description . . . . . . . . . . . : Intel(R) Ethernet Connection I218-LM
Physical Address. . . . . . . . . : 28-D2-44-C5-24-59
DHCP Enabled. . . . . . . . . . . : Yes
Autoconfiguration Enabled . . . . : Yes
Tunnel adapter isatap.attlocal.net:
Media State . . . . . . . . . . . : Media disconnected
Connection-specific DNS Suffix . : attlocal.net
Description . . . . . . . . . . . : Microsoft ISATAP Adapter
Physical Address. . . . . . . . . : 00-00-00-00-00-00-00-E0
DHCP Enabled. . . . . . . . . . . : No
Autoconfiguration Enabled . . . . : Yes
Tunnel adapter iphttpsinterface:
Media State . . . . . . . . . . . : Media disconnected
Connection-specific DNS Suffix . :
Description . . . . . . . . . . . : iphttpsinterface
Physical Address. . . . . . . . . : 00-00-00-00-00-00-00-E0
DHCP Enabled. . . . . . . . . . . : No
Autoconfiguration Enabled . . . . : Yes
Tunnel adapter 6TO4 Adapter:
Media State . . . . . . . . . . . : Media disconnected
Connection-specific DNS Suffix . :
Description . . . . . . . . . . . : Microsoft 6to4 Adapter
Physical Address. . . . . . . . . : 00-00-00-00-00-00-00-E0
DHCP Enabled. . . . . . . . . . . : No
Autoconfiguration Enabled . . . . : Yes
Tunnel adapter isatap.{FD31098B-E475-49A1-9AFA-8C43FF928F97}:
Media State . . . . . . . . . . . : Media disconnected
Connection-specific DNS Suffix . :
Description . . . . . . . . . . . : Microsoft ISATAP Adapter #2
Physical Address. . . . . . . . . : 00-00-00-00-00-00-00-E0
DHCP Enabled. . . . . . . . . . . : No
Autoconfiguration Enabled . . . . : Yes
Tunnel adapter isatap.domain.local:
Media State . . . . . . . . . . . : Media disconnected
Connection-specific DNS Suffix . :
Description . . . . . . . . . . . : Microsoft ISATAP Adapter #3
Physical Address. . . . . . . . . : 00-00-00-00-00-00-00-E0
DHCP Enabled. . . . . . . . . . . : No
Autoconfiguration Enabled . . . . : Yes
Tunnel adapter Teredo Tunneling Pseudo-Interface:
Connection-specific DNS Suffix . :
Description . . . . . . . . . . . : Teredo Tunneling Pseudo-Interface
Physical Address. . . . . . . . . : 00-00-00-00-00-00-00-E0
DHCP Enabled. . . . . . . . . . . : No
Autoconfiguration Enabled . . . . : Yes
IPv6 Address. . . . . . . . . . . : 2001:0:'mac':5a1c:342d:25dd:b4e1:12c8(Preferred)
Link-local IPv6 Address . . . . . : fe80::342d:25dd:b4e1:12c8%18(Preferred)
Default Gateway . . . . . . . . . :
NetBIOS over Tcpip. . . . . . . . : Disabled
Tunnel adapter isatap.{E1BE09BA-B38B-4F87-8893-E3D32A88EDFC}:
Media State . . . . . . . . . . . : Media disconnected
Connection-specific DNS Suffix . :
Description . . . . . . . . . . . : Microsoft ISATAP Adapter #4
Physical Address. . . . . . . . . : 00-00-00-00-00-00-00-E0
DHCP Enabled. . . . . . . . . . . : No
Autoconfiguration Enabled . . . . : Yes
Tunnel adapter isatap.{0C04B587-7861-4D8D-9DA9-6326AB71D701}:
Media State . . . . . . . . . . . : Media disconnected
Connection-specific DNS Suffix . :
Description . . . . . . . . . . . : Microsoft ISATAP Adapter #5
Physical Address. . . . . . . . . : 00-00-00-00-00-00-00-E0
DHCP Enabled. . . . . . . . . . . : No
Autoconfiguration Enabled . . . . : Yes
C:\WINDOWS\system32\LogSpace\{05471C14-7140-4651-84C2-230EC7D70628}>netsh int teredo show state
Teredo Parameters
Type : client
Server Name : 204.16.90.28 (Group Policy)
Client Refresh Interval : 30 seconds
Client Port : unspecified
State : qualified
Client Type : teredo host-specific relay
Network : unmanaged
NAT : restricted
NAT Special Behaviour : UPNP: No, PortPreserving: Yes
Local Mapping : 192.168.1.86:55842
External NAT Mapping : 75.30.237.55:55842
C:\WINDOWS\system32\LogSpace\{05471C14-7140-4651-84C2-230EC7D70628}>netsh int httpstunnel show interfaces
Interface IPHTTPSInterface (Group Policy) Parameters
Role : client
URL : https://uag.webdomain.com:443/IPHTTPS
Last Error Code : 0x0
Interface Status : IPHTTPS interface deactivated
C:\WINDOWS\system32\LogSpace\{05471C14-7140-4651-84C2-230EC7D70628}>netsh dns show state
Name Relocationution Policy Table Options
Query Failure Behavior : Always fall back to LLMNR and NetBIOS
if the name does not exist in DNS or
if the DNS servers are unreachable
when on a private network
Query Relocationution Behavior : Relocationve only IPv6 addresses for names
Network Location Behavior : Let Network ID determine when Direct
Access settings are to be used
Machine Location : Outside corporate network
Direct Access Settings : Configured and Enabled
DNSSEC Settings : Not Configured
C:\WINDOWS\system32\LogSpace\{05471C14-7140-4651-84C2-230EC7D70628}>netsh name show policy
DNS Name Relocationution Policy Table Settings
(ENTRIES OMITTED TO SAVE SPACE)
Settings for .domain.local
Certification authority : DC=local, DC=domain, CN=HDT CA
DNSSEC (Validation) : disabled
DNSSEC (IPsec) : disabled
DirectAccess (DNS Servers) : 2002:'mac':5a1d::'mac':5a1d
DirectAccess (IPsec) : disabled
DirectAccess (Proxy Settings) : Bypass proxy
C:\WINDOWS\system32\LogSpace\{05471C14-7140-4651-84C2-230EC7D70628}>netsh name show effective
DNS Effective Name Relocationution Policy Table Settings
(ENTRIES OMITTED TO SAVE SPACE)
Settings for .domain.local
Certification authority : DC=local, DC=domain, CN=HDT CA
DNSSEC (Validation) : disabled
IPsec settings : disabled
DirectAccess (DNS Servers) : 2002:'mac':5a1d::'mac':5a1d
DirectAccess (Proxy Settings) : Bypass proxy
C:\WINDOWS\system32\LogSpace\{05471C14-7140-4651-84C2-230EC7D70628}>netsh int ipv6 show int level=verbose
Interface Loopback Pseudo-Interface 1 Parameters
IfLuid : loopback_0
IfIndex : 1
State : connected
Metric : 50
Link MTU : 4294967295 bytes
Reachable Time : 40000 ms
Base Reachable Time : 30000 ms
Retransmission Interval : 1000 ms
DAD Transmits : 0
Site Prefix Length : 64
Site Id : 1
Forwarding : disabled
Advertising : disabled
Neighbor Discovery : disabled
Neighbor Unreachability Detection : disabled
Router Discovery : enabled
Managed Address Configuration : disabled
Other Stateful Configuration : disabled
Weak Host Sends : enabled
Weak Host Receives : disabled
Use Automatic Metric : enabled
Ignore Default Routes : disabled
Advertised Router Lifetime : 1800 seconds
Advertise Default Route : disabled
Current Hop Limit : 0
Force ARPND Wake up patterns : disabled
Directed MAC Wake up patterns : disabled
Interface Wireless Network Connection Parameters
IfLuid : wireless_0
IfIndex : 12
State : connected
Metric : 25
Link MTU : 1472 bytes
Reachable Time : 1101000 ms
Base Reachable Time : 1805000 ms
Retransmission Interval : 1000 ms
DAD Transmits : 1
Site Prefix Length : 64
Site Id : 1
Forwarding : disabled
Advertising : disabled
Neighbor Discovery : enabled
Neighbor Unreachability Detection : enabled
Router Discovery : enabled
Managed Address Configuration : disabled
Other Stateful Configuration : disabled
Weak Host Sends : enabled
Weak Host Receives : disabled
Use Automatic Metric : enabled
Ignore Default Routes : disabled
Advertised Router Lifetime : 1800 seconds
Advertise Default Route : disabled
Current Hop Limit : 64
Force ARPND Wake up patterns : disabled
Directed MAC Wake up patterns : disabled
Interface isatap.attlocal.net Parameters
IfLuid : tunnel_4
IfIndex : 22
State : disconnected
Metric : 50
Link MTU : 1280 bytes
Reachable Time : 27500 ms
Base Reachable Time : 30000 ms
Retransmission Interval : 1000 ms
DAD Transmits : 0
Site Prefix Length : 64
Site Id : 1
Forwarding : disabled
Advertising : disabled
Neighbor Discovery : enabled
Neighbor Unreachability Detection : disabled
Router Discovery : enabled
Managed Address Configuration : disabled
Other Stateful Configuration : disabled
Weak Host Sends : enabled
Weak Host Receives : disabled
Use Automatic Metric : enabled
Ignore Default Routes : disabled
Advertised Router Lifetime : 1800 seconds
Advertise Default Route : disabled
Current Hop Limit : 0
Force ARPND Wake up patterns : disabled
Directed MAC Wake up patterns : disabled
Interface Wireless Network Connection 2 Parameters
IfLuid : wireless_5
IfIndex : 15
State : disconnected
Metric : 5
Link MTU : 1500 bytes
Reachable Time : 24000 ms
Base Reachable Time : 30000 ms
Retransmission Interval : 1000 ms
DAD Transmits : 1
Site Prefix Length : 64
Site Id : 1
Forwarding : disabled
Advertising : disabled
Neighbor Discovery : enabled
Neighbor Unreachability Detection : enabled
Router Discovery : enabled
Managed Address Configuration : disabled
Other Stateful Configuration : disabled
Weak Host Sends : enabled
Weak Host Receives : disabled
Use Automatic Metric : enabled
Ignore Default Routes : disabled
Advertised Router Lifetime : 1800 seconds
Advertise Default Route : disabled
Current Hop Limit : 0
Force ARPND Wake up patterns : disabled
Directed MAC Wake up patterns : disabled
Interface iphttpsinterface Parameters
IfLuid : tunnel_5
IfIndex : 17
State : disconnected
Metric : 50
Link MTU : 1280 bytes
Reachable Time : 31500 ms
Base Reachable Time : 30000 ms
Retransmission Interval : 1000 ms
DAD Transmits : 1
Site Prefix Length : 64
Site Id : 1
Forwarding : disabled
Advertising : disabled
Neighbor Discovery : enabled
Neighbor Unreachability Detection : enabled
Router Discovery : enabled
Managed Address Configuration : enabled
Other Stateful Configuration : enabled
Weak Host Sends : enabled
Weak Host Receives : disabled
Use Automatic Metric : enabled
Ignore Default Routes : disabled
Advertised Router Lifetime : 1800 seconds
Advertise Default Route : disabled
Current Hop Limit : 0
Force ARPND Wake up patterns : disabled
Directed MAC Wake up patterns : disabled
Interface Local Area Connection Parameters
IfLuid : ethernet_6
IfIndex : 11
State : disconnected
Metric : 5
Link MTU : 1500 bytes
Reachable Time : 31500 ms
Base Reachable Time : 30000 ms
Retransmission Interval : 1000 ms
DAD Transmits : 1
Site Prefix Length : 64
Site Id : 1
Forwarding : disabled
Advertising : disabled
Neighbor Discovery : enabled
Neighbor Unreachability Detection : enabled
Router Discovery : enabled
Managed Address Configuration : disabled
Other Stateful Configuration : disabled
Weak Host Sends : enabled
Weak Host Receives : disabled
Use Automatic Metric : enabled
Ignore Default Routes : disabled
Advertised Router Lifetime : 1800 seconds
Advertise Default Route : disabled
Current Hop Limit : 0
Force ARPND Wake up patterns : disabled
Directed MAC Wake up patterns : disabled
Interface 6TO4 Adapter Parameters
IfLuid : tunnel_6
IfIndex : 19
State : disconnected
Metric : 50
Link MTU : 1280 bytes
Reachable Time : 39500 ms
Base Reachable Time : 30000 ms
Retransmission Interval : 1000 ms
DAD Transmits : 0
Site Prefix Length : 64
Site Id : 1
Forwarding : disabled
Advertising : disabled
Neighbor Discovery : disabled
Neighbor Unreachability Detection : disabled
Router Discovery : enabled
Managed Address Configuration : disabled
Other Stateful Configuration : disabled
Weak Host Sends : enabled
Weak Host Receives : disabled
Use Automatic Metric : enabled
Ignore Default Routes : disabled
Advertised Router Lifetime : 1800 seconds
Advertise Default Route : disabled
Current Hop Limit : 0
Force ARPND Wake up patterns : disabled
Directed MAC Wake up patterns : disabled
Interface isatap.{FD31098B-E475-49A1-9AFA-8C43FF928F97} Parameters
IfLuid : tunnel_7
IfIndex : 21
State : disconnected
Metric : 50
Link MTU : 1280 bytes
Reachable Time : 33000 ms
Base Reachable Time : 30000 ms
Retransmission Interval : 1000 ms
DAD Transmits : 0
Site Prefix Length : 64
Site Id : 1
Forwarding : disabled
Advertising : disabled
Neighbor Discovery : enabled
Neighbor Unreachability Detection : disabled
Router Discovery : enabled
Managed Address Configuration : disabled
Other Stateful Configuration : disabled
Weak Host Sends : enabled
Weak Host Receives : disabled
Use Automatic Metric : enabled
Ignore Default Routes : disabled
Advertised Router Lifetime : 1800 seconds
Advertise Default Route : disabled
Current Hop Limit : 0
Force ARPND Wake up patterns : disabled
Directed MAC Wake up patterns : disabled
Interface isatap.domain.local Parameters
IfLuid : tunnel_8
IfIndex : 39
State : disconnected
Metric : 50
Link MTU : 1280 bytes
Reachable Time : 36000 ms
Base Reachable Time : 30000 ms
Retransmission Interval : 1000 ms
DAD Transmits : 0
Site Prefix Length : 64
Site Id : 1
Forwarding : disabled
Advertising : disabled
Neighbor Discovery : enabled
Neighbor Unreachability Detection : disabled
Router Discovery : enabled
Managed Address Configuration : disabled
Other Stateful Configuration : disabled
Weak Host Sends : enabled
Weak Host Receives : disabled
Use Automatic Metric : enabled
Ignore Default Routes : disabled
Advertised Router Lifetime : 1800 seconds
Advertise Default Route : disabled
Current Hop Limit : 0
Force ARPND Wake up patterns : disabled
Directed MAC Wake up patterns : disabled
Interface Bluetooth Network Connection Parameters
IfLuid : ethernet_9
IfIndex : 14
State : disconnected
Metric : 50
Link MTU : 1500 bytes
Reachable Time : 17000 ms
Base Reachable Time : 30000 ms
Retransmission Interval : 1000 ms
DAD Transmits : 1
Site Prefix Length : 64
Site Id : 1
Forwarding : disabled
Advertising : disabled
Neighbor Discovery : enabled
Neighbor Unreachability Detection : enabled
Router Discovery : enabled
Managed Address Configuration : disabled
Other Stateful Configuration : disabled
Weak Host Sends : enabled
Weak Host Receives : disabled
Use Automatic Metric : enabled
Ignore Default Routes : disabled
Advertised Router Lifetime : 1800 seconds
Advertise Default Route : disabled
Current Hop Limit : 0
Force ARPND Wake up patterns : disabled
Directed MAC Wake up patterns : disabled
Interface Wireless Network Connection 3 Parameters
IfLuid : wireless_9
IfIndex : 16
State : disconnected
Metric : 5
Link MTU : 1500 bytes
Reachable Time : 17000 ms
Base Reachable Time : 30000 ms
Retransmission Interval : 1000 ms
DAD Transmits : 1
Site Prefix Length : 64
Site Id : 1
Forwarding : disabled
Advertising : disabled
Neighbor Discovery : enabled
Neighbor Unreachability Detection : enabled
Router Discovery : enabled
Managed Address Configuration : disabled
Other Stateful Configuration : disabled
Weak Host Sends : enabled
Weak Host Receives : disabled
Use Automatic Metric : enabled
Ignore Default Routes : disabled
Advertised Router Lifetime : 1800 seconds
Advertise Default Route : disabled
Current Hop Limit : 0
Force ARPND Wake up patterns : disabled
Directed MAC Wake up patterns : disabled
Interface Teredo Tunneling Pseudo-Interface Parameters
IfLuid : tunnel_9
IfIndex : 18
State : connected
Metric : 50
Link MTU : 1280 bytes
Reachable Time : 14500 ms
Base Reachable Time : 15000 ms
Retransmission Interval : 2000 ms
DAD Transmits : 0
Site Prefix Length : 64
Site Id : 1
Forwarding : disabled
Advertising : disabled
Neighbor Discovery : enabled
Neighbor Unreachability Detection : enabled
Router Discovery : enabled
Managed Address Configuration : disabled
Other Stateful Configuration : disabled
Weak Host Sends : enabled
Weak Host Receives : enabled
Use Automatic Metric : enabled
Ignore Default Routes : disabled
Advertised Router Lifetime : 1800 seconds
Advertise Default Route : disabled
Current Hop Limit : 0
Force ARPND Wake up patterns : disabled
Directed MAC Wake up patterns : disabled
Interface isatap.{E1BE09BA-B38B-4F87-8893-E3D32A88EDFC} Parameters
IfLuid : tunnel_10
IfIndex : 20
State : disconnected
Metric : 50
Link MTU : 1280 bytes
Reachable Time : 41000 ms
Base Reachable Time : 30000 ms
Retransmission Interval : 1000 ms
DAD Transmits : 0
Site Prefix Length : 64
Site Id : 1
Forwarding : disabled
Advertising : disabled
Neighbor Discovery : enabled
Neighbor Unreachability Detection : disabled
Router Discovery : enabled
Managed Address Configuration : disabled
Other Stateful Configuration : disabled
Weak Host Sends : enabled
Weak Host Receives : disabled
Use Automatic Metric : enabled
Ignore Default Routes : disabled
Advertised Router Lifetime : 1800 seconds
Advertise Default Route : disabled
Current Hop Limit : 0
Force ARPND Wake up patterns : disabled
Directed MAC Wake up patterns : disabled
Interface isatap.{0C04B587-7861-4D8D-9DA9-6326AB71D701} Parameters
IfLuid : tunnel_11
IfIndex : 23
State : disconnected
Metric : 50
Link MTU : 1280 bytes
Reachable Time : 40000 ms
Base Reachable Time : 30000 ms
Retransmission Interval : 1000 ms
DAD Transmits : 0
Site Prefix Length : 64
Site Id : 1
Forwarding : disabled
Advertising : disabled
Neighbor Discovery : enabled
Neighbor Unreachability Detection : disabled
Router Discovery : enabled
Managed Address Configuration : disabled
Other Stateful Configuration : disabled
Weak Host Sends : enabled
Weak Host Receives : disabled
Use Automatic Metric : enabled
Ignore Default Routes : disabled
Advertised Router Lifetime : 1800 seconds
Advertise Default Route : disabled
Current Hop Limit : 0
Force ARPND Wake up patterns : disabled
Directed MAC Wake up patterns : disabled
C:\WINDOWS\system32\LogSpace\{05471C14-7140-4651-84C2-230EC7D70628}>netsh advf show currentprofile
Private Profile Settings:
State ON
Firewall Policy BlockInbound,AllowOutbound
LocalFirewallRules N/A (GPO-store only)
LocalConSecRules N/A (GPO-store only)
InboundUserNotification Enable
RemoteManagement Disable
UnicastResponseToMulticast Enable
Logging:
LogAllowedConnections Disable
LogDroppedConnections Disable
FileName %systemroot%\system32\LogFiles\Firewall\pfirewall.log
MaxFileSize 4096
Ok.
C:\WINDOWS\system32\LogSpace\{05471C14-7140-4651-84C2-230EC7D70628}>netsh advfirewall monitor show consec
Global Settings:
IPsec:
StrongCRLCheck 0:Disabled
SAIdleTimeMin 5min
DefaultExemptions ICMP
IPsecThroughNAT Never
AuthzUserGrp None
AuthzComputerGrp None
StatefulFTP Enable
StatefulPPTP Enable
Main Mode:
KeyLifetime 60min,0sess
SecMethods DHGroup2-AES128-SHA256,DHGroup2-AES128-SHA1,DHGroup2-3DES-SHA1
ForceDH No
Categories:
BootTimeRuleCategory Windows Firewall
FirewallRuleCategory Windows Firewall
StealthRuleCategory Windows Firewall
ConSecRuleRuleCategory Windows Firewall
Quick Mode:
QuickModeSecMethods ESP:SHA1-None+60min+100000kb,ESP:SHA1-AES128+60min+100000kb,ESP:SHA1-3DES+60min+100000kb,AH:SHA1+60min+100000kb
QuickModePFS None
Security Associations:
Main Mode SA at 03/24/2015 14:21:44
Local IP Address: 2602:304:'mac3':d370:f9ce:db89:87ad:'mac4'
Remote IP Address: 2002:'mac':5a1d::'mac':5a1d
Auth1: ComputerCert
Auth2: UserNTLM
MM Offer: None-AES128-SHA256
Cookie Pair: 9398e38420480425:51071d5bae9eb503
Health Cert: No
Quick Mode SA at 03/24/2015 14:21:44
Local IP Address: 2602:304:'mac3':d370:f9ce:db89:87ad:'mac4'
Remote IP Address: 2002:'mac':5a1d::'mac':5a1d
Local Port: Any
Remote Port: Any
Protocol: Any
Direction: Both
QM Offer: ESP:SHA1-AES192+60min+100000kb
PFS: None
Thanks again, -
Search in library not working for some libraries (and for others it does work)
Dear SharePoint/Search adepts
As you all know, in SharePoint 2013 you have the
possibility to search from a library.
Today I encountered some strange behavior…
We've deployed a SharePoint 2013 environment, 4 SharePoint servers (2wfe +2app),
and an additional server dedicated to Search and all of its components. This with
a SQL cluster as a backend
everything works just perfect...
Except certain search boxes (above a library) do not
return results when trying to search within the library.
If we take the same query and execute it on the site
itself, it returns the desired result set.
The odd thing is, that it doesn’t affect all the libraries, in some it works,
in some it doesn’t.
no error messages or something like it, search just playing dumb
I’ve checked several times, all the desired documents
are crawled. (And can be found in the site search)
I’m quite confident and experienced with search, but
this blows my mind and I do not know where to look anymore ...
Does anyone have an idea?
Thx for helping out!
Daancheck for the scope for the search configured
Whenever you see a reply and if you think is helpful, click "Vote As Helpful"! And whenever
you see a reply being an answer to the question of the thread, click "Mark As Answer -
Lion Server network accounts not working on some computers.
Hello all -
I'm currently having an issue with network accounts working on some Macs but not others. I have a Mac Mini and a MacBook Pro. The Mac Mini works fine and I can login and sync my network account with the server just fine. However, I cannot connect to it from my MBP.
When I try and connect I get an error that says "You are unable to log in to the user account "xxxx" at this time. Logging in to the account failed because an error occurred."
If I login through console (by typing in ">console" in the username field) I get an error that says the user does not have a home directory...
I have searched numourous other forums but I have not found a solution that seems to solve this problem. I have unbound and re-bound my client to the open directory and I have restarted file sharing. Neither has solved the problem. I have a feeling the issue originates somewhere on the MBP since I can log in to the Mac Mini without any problems.
Anymore suggestions?Thanks for your suggestion, SolidWood. Unfortunately it didn't help.
After a 90 minute phone call with AppleCare, this issue has finally been resolved. Here is what the solution was. Turns out it was pretty simple but it took a while to find it.
First we created a test user and left the home folder set to Local Only in the Server App. I was successfully able to login with the test user on both clients but since there were no mobility preferences set, it was pretty basic.
Then, we removed the Users sharepoint from file sharing, turned off file sharing to disconnect any users, and restarted the server. Then we created a new folder on the Server HD with a random name. We chose Darron. We created a new sharepoint in file sharing (with it still turned off), and shared the new folder called Darron. Double click on the sharepoint and scroll to the bottom and check the box that says "Make available for home directories over AFP". Then we restarted file sharing.
Then we opened Workgroup Manager, clicked on the problem user in the left sidebar, clicked on the Home option at the top, and there were three things listed:
(None)
afp://servername.com/Users
afp://servername.com/Darron
Then we removed the Darron sharepoint from file sharing, and found that it was still listed as a home directory under the problem user.
This was the root of the problem. The system didn't know which path to use as the home directory.
Sooooo...
In the server app, we opened the Directory Utility (Tools in the menubar, Directory Utility). Clicked on Directory Editor. Authenticate to the directory using the diradmin login. Changed view settings to match this below:
In the left column, there were two paths listed for home mounts. We deleted both of them, saved changes, and closed directory editor.
Then, we restarted workgroup manager and both paths had been deleted from the users home listings. This was begining to solve the problem.
In the Server App, we recreated the users sharepoint, made it available for home directories, and restarted file sharing and workgroup manager. Now only one path is listed for the home folder for all the users.
This solved my problem of not being able to login on the MBP. The system synced the home folder and all was well. On the Mac Mini, I had to delete the problem account, un-bind from the network server, re-bind, and recreate the account. Now both clients are sycning perfectly and all is well.
Thank God I bought AppleCare! Thanks to everyone else for their help and suggestions.
As a recap, the problem of not being able to login to the MacBook Pro was caused by having multiple paths to the multiple home folders. These rogue paths were added somewhere in the troubleshooting process to try and recreate the home directories before I called AppleCare. To solve this, we had to remove the directory listings from accounts using Directory Editor, remove and recreate the users sharepoint in file sharing. The syncing problem on the Mac Mini was also created when multiple paths were introduced. The system didn't know which files to use.
Taylor -
IOS 5 Notifications Not Working for Some Third Party Apps
Recently updated my iPhone 4 to iOS5. Notification center worked perfectly for a week, but then I noticed that certain apps (Beluga) would not show up in the notification center despite receiving new messages. The home page didnt update with a badge either. It seems as if push notifications for some third party apps are not working correctly.
I have already attempted all of these to correct the problem to no avail:
1. Confirming notification settings for each application
2. Turning notifications off and then on
3. Removing and reinstalling app
4. Restarting the iPhone
5. Shutting down and powering up the iPhone
6. Restoring the iPhoneHaving the same problem... Ipad 2 running iOS 5 working fine. My iPhone 4s gets the occasional Facebook notification but not much else. Got home today and had about 5 notifications on the iPad that never came through to the iPhone. Tried everything you tried and nothing....
-
Delete all files in a directory not working for some files
I have a requirement like wants to delete all the files in a directory. (These files got generated through some other program.)
Problem is file.delete() is returning false for some of the files..
(donno the reason .. could be bcoz of file closing issues/locking issues.)
Looking for a solution where i can delete a file forcefully irrespective of whether the file is opened or not.
Thanks
Sriniare you on windows? if so, it's almost impossible to delete something another process has open.
-
TS3274 audio dose not work for some apps on my ipad
For some reason my Ipad is choosing which apps to produce audio
If you have no sound at all, even in the Music App, try rebooting the iPad.
Reboot the iPad by holding down on the sleep and home buttons at the same time for about 10-15 seconds until the Apple Logo appears - ignore the red slider if it appears on the screen - let go of the buttons. Let the iPad start up.
If you lost sounds for keyboard clicks, games or other apps, email notifications and other notifications, system sounds may have been muted.
System sounds can be muted and controlled two different ways. The screen lock rotation can be controlled in the same manner as well.
Settings>General>Use Side Switch to: Mute System sounds. If this option is selected, the switch on the side of the iPad above the volume rocker will mute system sounds.
If you choose Lock Screen Rotation, then the switch locks the screen. If the screen is locked, you will see a lock icon in the upper right corner next to the battery indicator gauge.
If you have the side switch set to lock screen rotation then the system sound control is in the control center. Swipe up from the bottom of the screen to get to control center . Tap on the bell icon and system sounds will return.
If you have the side switch set to mute system sounds, then the screen lock can be accessed in the same manner as described above.
This support article from Apple explains how the side switch works.
http://support.apple.com/kb/HT4085
Maybe you are looking for
-
Cannot find oracle.portal.provider.v2 package ,
We are looking for PDK 10.1.2.0.2. and are unable to find anywhere , any ideas ? where can i find it
-
Executing Sql - whats happening on the server
Hi, I am using Oracle 8.17 on a AIX box. When i run queries that have to do full table scans of a large table it virtually cripples my system. (nmon shows lots of disk activity / paging) . Even when running Select count(col1) from large_tab; Im tryin
-
Why does my iTunes crash whenever I try to refresh my podcasts?
Whenever I press the "Refresh" button on my podcasts, I get the error message "iTunes has stopped working." No particular reason why or error code, it simply "stops working."
-
Post Depreciation to product cost
I want to include depreciation costs in product costing. Is there any way to post the depreciation costs other than using activity types
-
Apple ID and PW changes create problems on IPad ICloud
I changed my Apple ID and password on the apple website but changing it on Ipad to connect with Icloud using new parameters seems to be a problem, will not accept new pw for deleting old account. Please help