Does having two networks on the same router cut the speed of each network?

I have successfully been using a FiOS and Time Capsule network for over two years. When I had it installed the FiOS service man set up a network without the Apple Time Capsule. I later set up an additional network that included the Time Capsule. My first question is, does that mean I have cut the speed potential in half? If so, can I safely delete the unsused network?

Answered on other post.

Similar Messages

There are two iMacs connected through same router in my house but one refuses to login to facebook and other logged in sites. local techies are bemused, I have just reinstalled OSX and still have the problem. Login page recycles and no errors reported.

There are two iMacs connected through same router in my house but one refuses to login to facebook and other logged in sites. Local techies are bemused, I have just reinstalled OSX and still have the problem. Login page recycles, I get no further and no errors reported. Safari, Opera and Firefox. Deleted cookies and chain but still no action.

If you have not already done so, read the router's user manual troubleshooting section and/or contact its customer service department/forums.
If still having problems, post back w/details of all you have tried to resolve the problems along w/the troubleshooting solutions that the "local techies" had you try.

Having two copies of the same report on the same page.

buddy.....I've tried urs suggestion,but now it is showing two quotations(easily adjustible in 2 pages) on 3 pages. I've tried Page Protect to set to No for all the repeating frames and fixed the horizontal & vertical length of all repeating frames.
plzzz let me to describe my report more deeply, it picks data from two tables,one master table containing quotation#,customer-id, date.2nd block contains details about repairing items. so all the data is in two
repeating frames which can be easily printed in half page. 2nd copy of this quotation will also print on the same page in the lower half portion of a page.
is it enough for u????
still if u peeps have any problem in understanding my problem then I think u peeps should have a look on my quotation report so that u may have a better idea of this problem.

hi gentlemen...I've solved this problem by doing a trick that I've create dual items in data-model i.e two queries and data group for each block and printed them on the same page,so it has solved my problem, is it the right way I've done the things or there is some other better idea???

Best way to go about having two people use the same form?

Hi guys,
Relativly new to livecycle and I need some help.
I've been asked to make a form that 2 different people will have access too, what I need to do is as followed:
Person 1
Only has access to the first 5 pages and is able to fill out the form
Person 2
Has access to the WHOLE document and can see what PERSON 1 has entered.
Can this be done with two different versions of the document, or will it have to be all as one?
Regards

Well I have done it before by using a button which the second person clicks and this brings up a messagebox which asks for a password. If the password is entered correctly the rest of the form (which is originally set to hidden) will become visible. The code in the click event of the button is something like (in formcalc):
var correctpassword = xfa.host.response("Password:","For office use only","",1)
if (correctpassword == "whateverYouWantYourPasswordToBe") then
restOfForm.presence = "visible"
$.presence = "hidden"
else xfa.host.messageBox("You have entered the wrong password","For office use only",1)
endif

I'm having two problems: a) the browser won't load unless I go through profile manager and at time it won't even load from there and b) the search bar won't search it does nothing as does some links like your link to live chat

This has only started happening after my last firefox update. I tried a reinstall as well with no luck

Wow that was really quick, thank you so much. Im not sure at all which version it was because i said it was around 4 years ago he bought it. I know it isn't under his username, since he's a PC person (ugh) so i know its probably registered to one of our actual names. isn't there some way to look it up since we did register it, because I'm not even sure where the disks are from when we bought it (we've moved a lot and also have two storage lockers, i know i would have kept it with other disks) but my cd rom drive is actually broken on my computer as well ( i think it got stepped on and is now squished and won't eject or run disks.)
So is there anyway they can look up that its registered to one of our names since we did register it when we bought and installed it, or do i really have to find the disk with some sort of proof of purchase (i know there would be no receipt after all this time)
either way, ill do what you suggested to the best of my abilities and thank you so much for answering my questions, i can't even open the program as its incompatible and find out the info from that) so I'm in a bit of a pickle and your response was so thorough and it didn't seem to be posted long enough to even write a well researched response, thanks, all the best,
sarucia

My Mac book pro is having two issues at the same time.

HI Guys, My Mac book pro ...touch pad is acting funny...going all over the screen, I have bare minimum control over it. and to make matters worse, the Battery of my mac book pro is not charging, the charger is showing green light (not Orange) - the battery icon on teh screen is showing 'Not Charging'.
as soon as I pull the battery charger out the whole sytem just shuts down.
Please assist.

mattw gx wrote:
This is a pretty common failure for MacBook Pros.
Perhaps you mean This is a pretty common failure for Sony batteries.

Vendor payment having two bank accounts in same branch, through APP

Hi,
I want to make payments to a particular vendor who has two bank accounts in the same branch.
Also his invoice says to pay 40% to one account and 60% of invoice amount to other account
How should i move forward especially when making payments through APP.
Kindly help.
Regards,
Parin Vadodaria

thanks,
It is allowing me to put the partner bank type in FBL1N but my query is:
If two line items generated during FB60 it should allow me to assign different Partner Bank for different line items on the screen of FB60....
Is that possible?
Thanking You,
Parin

HT4914 Does it bill you at the beginning of each year or one year from purchase

When you subscribe to the iTunes Match does it bill you every year on the same date or would it bill me now & again January 1st?

Welcome to the Apple Community.
On the same date (anniversary of subscription) each year.

Two users in the same Mac accessing one TimeCapsule

Hi,
How can i make two user accounts in the same Mac access simultaneously the same TimeCapsule?
I've tried setting them to use accounts to connect to TimeCapsule as well as using a single password for TimeCapsule.
But i keep having the same problem. When one user accesses the time capsule the other gets ejected or the TimeCapsule folder appears with a forbidden sign.
What do i have to do?
Please help.
Thanks in advance

I think i understand what is happening.
Leopard mounts the TimeCapsule disk using mount_afp command and any disk mounted with mount_afp will automatically have as owner <user>:staff and read and write permissions only to the owner. All other users have access denied.
(If anyone knows how to change the default permissions of mount_afp please reply!)
If like me, you have two user accounts in the same Mac (lets say user1 and user2) and use fast user switching a lot like i do, since it is a family computer, you'll have serious problems since what happens is the following:
1. Mount the Timecapsule in user1.
2. Fast user switching to user2.
3. The TimeCapsule will appear unmounted in user2
4. Mount the TimeCapsule in user2.
5. List the /Volumes folder and you'll see something like this
drwx------ user1:staff /TimeCapsule
drwx------ user2:staff /TimeCapsule-1
No problem... I can live with having two mounts for the same network disk.
The problem is the following...
6. Fast user switch to user1 again.
7. Open a finder window
8. On the left the TimeCapsule is listed as a network drive (as expected) and is shows as mounted!
However... The association has changed and once i click the TimeCapsule icon in the sidebar it now points to /Volumes/TimeCapsule-1 and therefore user1 has permission denied.
9. I opened a terminal window with user1 and went to /Volumes/TimeCapsule and everything was ok!.
So the conclusion is... the finder window sidebar TimeCapsule is pointing to a Volume it shouldn't be...
How is it possible to correct this situation???
Please help! I just want a way to have two users on the same machine using the same time capsule at the same time.
Thanks!

Two different Routers and same subnet, is it possible?

Hi i have been presented with a problem that a friend of mine is having.
There is two different Cisco routers on different location.
example:
router1 : 10.8.10.1 (has DHCP/FTP server)
router2 : 10.8.12.1 (needs to talk to DHCP/FTP server on router1)
the router2 has different ip configured but is it possible to change this to the same subnet as router 1? like 10.8.10.4?
The DHCP/FTP server have been defined with scope 10.8.12.0 and on the Cisco switch on router2 its been configured (ip helper address DHCP-IP)
this works, the clients connected to router2 gets ip from DHCP server ,but there is no FTP traffic.
i figure its because the DHCP/FTP server doesent understand the other IP, so if its possible to setup a kind of mulitVPN to get the same subnet on router2 as router1 the FTP server can "see" the other router2 because it has the same subnet and ip range.
Thank you for any experience, i really stuck on this one

John,
to simply put it having two routers on the same subnet is not possible as the purpose of a router is to route traffic between DIFFERENT networks. In order to accomplish this you will need routers and switches that understand VLANs and VLAN tagging.
Hope this Helps
Blake Wright
Cisco SBSC Network Engineer

Having Two different Servlet applications on one EJB applciation

Hi,
I am running two web applications on tomcat servlet engine
and one on orion servlet Engine both Access EJBs deployed on Orion application server which has the web app also.
what are the consequences of having two different webapps
accessing same EJB app in Real Time
Thanks
Jay

It's one of the expected usage models. You often see people doing wireless this way, as a separate webapp pointing to the same set of EJBs.

Responding to two user events with same name

LV 2013, Win 7, & LVRT 2013, PharLap OS
I have a situation where I create an ARRAY of User Events, one for each "domain" .
A "domain" is an area of DAQ: there is a SCXI domain, a CDAQ domain, an EtherCAT domain, several domains dealing with TCP instruments etc., about 25 domains all told. The name of the event is "New Channels This Domain".
When a new configuration comes to the PXI from the host, I sort out the channels by their domain and generate a user event for whichever domains have channels that have changed: more channels, fewer channels, differences. If a domain has no channels that have changed, I do not generate an event for it.
There is a handler for each domain: in that handler, I pick out the event for this domain from the array, and register to receive it. I have an event structure that responds to the NEW CHANNELS THIS DOMAIN event. Since it is an array, then no matter which domain I select, the name of the array is "New Channels This Domain".
All this works fine.
Now I have a situation where it makes sense to have one handler for TWO domains.
I can pick out TWO elements of the array just fine, and register them both. (See attached pic) But now, in the EDIT EVENTS FOR THIS CASE list, I have TWO events called "New Channels This Domain". I can select one for one case, and the other for the other case and it seems to work.
--- Is there any heartache ahead with this scheme?
--- If I change the events in the clusters before, is it going to confuse LabVIEW?
--- Is there something I can do to change the name of the event after I pick it out of the array?
--- Is there something I SHOULD do at that point?
Like I said, it seems to work, but I'm leery of it staying that way - I've had event structures disturbed before (LV2010) when changing cluster order.
Steve Bird
Culverson Software - Elegant software that is a pleasure to use.
Culverson.com
Blog for (mostly LabVIEW) programmers: Tips And Tricks

CoastalMaineBird wrote:
Thanks, Greg for that link. I gave kudos to the idea of the COERCE TO TYPE function, and it seems like it would do the trick, but as of LV2014 it's still not on the palette.
My question still remains: is it necessary? Will the event structure remember that it's supposed to use the SECOND event named "X", through all edits and recompiles? My guess is no, but I'll listen to alternative stories.
I've been using the Coerce to type for this and enums in versions 2011 through 2014 since learning about it. I've seen no issue using it in these cases. I'm guessing it doesn't behave in an expected way for extreame uses which is why NI doesn't release it yet.
As for would it always know to go to the second event if they are named the same? My guess is yes. They maybe named the same but they have different references. I would think it would be just like having two controls with the same label. You should never do this, but if you did, and made a local variables on one and wrote to it, it would always write to the correct control. It would never write to the different control with the same name. Now even if this is the case it could be confusing to a developer looking at the code, which is why I strongly suggest having unique names. But if you don't I suspect every thing would work fine, just have a bold comment or something explaining what each case actually is handling.
Unofficial Forum Rules and Guidelines - Hooovahh - LabVIEW Overlord
If 10 out of 10 experts in any field say something is bad, you should probably take their opinion seriously.

Is it possible to install two SAP system with same SID but different instance numbers on one host?

Is it possible to install two SAP system with same system ID (SID) but different instance numbers on one host?
If yes, then how?
If no, then why?
Thanks in advance.
Regards,
Sarim

Is it possible to install two SAP system with same system ID (SID) but different instance numbers on one host?
Yes, it is possible. If one is CI (PAS) and the second one is an AS (AAS). In this case there will be only one database.
If you are talking about two separate SAP systems with separate databases (Eg: A BI and an ECC) with the same SID then the problem will be with the database (Eg: Oracle)
The database will be installed under /oracle/SID/112_64 (ORACLE_HOME) unless one database is running on 10 G and in that case the ORACLE_HOME will be /oracle/SID/102_64
The next issue will be with the SAP file systems like /sapmnt/SID
The most important problem will be with the switch to the sidadm and orasid users and the conflicts there. If there is a need to stop one of the SAP systems and if you do a switch to sidadm and issue a stopsap command which system will be stopped ?
These are few of the many problems I can think of.
So if we are talking about two separate systems with their own databases I would rule out the possibility of having two systems with the same SID.
Regards
RB

An " " symbol at the top of each JavaHelp page?

Hello all,
I have generated JavaHelp off an imported Word 2007 document on a Windows 7 box. Interestingly, an unsightly ">" (the greater than sign) is appearing at beginning of each help page when ported to my Fedora 13/Linux box. The preview of the JavaHelp on the Windows 7 machine (where I generated the JavaHelp) does not show this ">" at the top of each help page.
Any idea why the unexpected ">" is showing up at the top of each help page on Fedora/Linux box?
Thanks.
- Arefin

I'm also using version 9. I didn't have to set the JAVA_HOME variable. After I reinstalled RoboHelp and compiled my JavaHelp project for the very first time, it asked me where my Java and JavaHelp were installed (in two separate prompts after I clicked Save and Generate). After that, the > at the top of each file went away. However, when I did a search, it was still displaying the title of each of my search results as:
10 > >
5 > >
2 > >
When I compiled to a clean directory, this was fixed and again displayed the actual page title instead of the > symbol.

How can I change the speed of slides for each song on the custom list?

Hello - I am working on an anniversary slideshow in iphoto on my Mac. It contains 145 photos. I have a custom playlist of two songs. I want to adjust the speed of the slideshow in the beginning to be slower because the song is slower. Then I want the photos to move faster at the end. I did notice I can specifically define the speed for each of the slides manually, but that would take forever. Does anyone have a recommendation of a trick for doing this in batches?

What is your iPhoto version?
In iPhoto '11 you can change the duration for several slides at once, if you are using the Classic Theme or the Ken Burns theme.
In that case do the following: SElect several slides at once and open the Settings. Click the "This slde" tab and change the "Show this slide for ..." setting.

Does having two networks on the same router cut the speed of each network?

Similar Messages

Maybe you are looking for