Does NET8 2-tier server have a simultaneous connection limit ?

Does NET8 2-tier server have a simultaneous connection limit ?
I came across one article that has a 100 simultaneous connection listing for 2-tier.
Please let me know
George

Yes, My WRT610N is currently using both 2.4Ghz and 5.0Ghz at the same time. I'm using WPA2 Private with AES on both frequencies. I'm currently getting 135mbps on both frequencies. Both are stable at 30 feet but the Actual throughput is better on the 2.4Ghz frequency and also range.
I think the reason that i'm restricted to 135mbps is the Intel wifi link 5100 can only transfer at a maximum of 150 mbps.
This router has always been stable although i did loose my network one night it dived to 6mbps for apparently no reason at all. But i believe that this issue was due to an update on my Laptop. I fixed this by removing the Wifi adapter drivers and reinstalling them.
5 G Network
Mode:   Wireless-N Only
Network Name (SSID):   N/A
Radio Band:   Wide - 40MHz Channel
Wide Channel:   38
Standard Channel:   36
Security:   WPA2-Personal
SSID Broadcast:   Enabled
2.4 G Network
Mode:   Mixed
Network Name (SSID):   N/A
Radio Band:   Wide - 40MHz Channel
Wide Channel:   8
Standard Channel:   6
Security:   WPA2-Personal
SSID Broadcast:   Enabled
** Note these settings are from the Status / Wireless Network page on the router, all wide channel / standard channels are actually set to Auto

Similar Messages

Does the socket implementation suport only 2 simultaneous connections?

Hi all,
I implemented this server the traditional way:
public void run() {
   while(state.isRunning()) {
      try {
         System.out.println("listening...");
         sourceSock = ssock.accept();
         System.out.println("new incoming connection");
         sourceSock.setSoTimeout(config.getHttpTimeout());
         new Thread(new ProxyHttpConnectionWorker(sourceSock, config)).start();
      } catch (IOException _ex) {
         config.out.trace(_ex.getMessage());
}It seems ok to me. I implemented it several times in a lot of situations.
However, this time I noted that after two simultaneous socket connections are opened (via accept()), all other connections I try to make from a client are blocking until one of the first two sockets close().
I mean, it seems to be blocking the incoming connections in the accept() method, because the string "listening..." was printed, but the string "new incoming connection" is only printed when one of the two initial sockets close()
Why is this happening? Is this correct?
I implemented it with J2SE 1.3.1 in a windows NT 4 workstation machine.
Is this an Operating System problem? A TCP/IP problem? Is the problem in the java socket implementation? Is there any flaw in my code?
Thank you all in advance,
Filipe Fedalto

Hi, Chuck
It could also be the case.
Actually, I am implementing a proxy server. All the major work is done and were it not this accept() problem it would be functioning very well.
The server is running in my machine and I am testing it by issuing 4 simultaneous HTTP requests from Internet Explorer 5.5 from my own machine itself. So, you see, this could be the problem, according to what you've just said.
I try to open the 4 browser connections simultaneously, but the servers' accept() method only seems to receive 2 of them at a time.
What do you think about it?
Just in case, I will try and test it using Netscape. Let's see if the number of simultaneous connections change...
Notwithstanding, why do the browsers limit the number of concurrent connections? I might think that this is because it is better to open a single page or two faster than trying to open 5 or 6 pages slowly... is this the point?
Thank you very much!
Filipe Fedalto

Does my iPod touch 4g have to be connected to wifi in order for me to find it on my computer via Find My Iphone or iCloud?

Does it have to be connected to wifi?

There is no way to know if the iPod has been restore and used with another Apple ID unless Apple is presented with a court order.

HT4864 How come when I use the automate iCloud setup, does the incoming mail server have a different address then specified by these instructions?

The IMAP sever that automatically set up is p08-imap.mail.me.com?

So I guess using Apple Token for authenication is OK, instead of the prescibed Name and Password per the http://support.apple.com/kb/HT4864?

Does any of linksyses routers have the ability to limit download speed

hi i have the e2500 and the Qos setting does not have the downloading limit setting on it,
i would like a way to limit other computers in my home network.
does anyone know of a good router with this ability?
thanks

Hi J.Runyon,
The main purpose is to prevent the Psiphone application running ,right ?
AppLocker has the ability to deny applications from running simply by excluding them from the list of allowed applications .
Here is a link for reference of using Scenarios.
AppLocker Policy Use Scenarios
https://technet.microsoft.com/en-us/library/ee424357(v=ws.10).aspx
We can refer to the following link to configure the group policy,please pay attention that the " Application Identity service " should be running .
How to configure AppLocker Group Policy to prevent software from running
http://social.technet.microsoft.com/wiki/contents/articles/5211.how-to-configure-applocker-group-policy-to-prevent-software-from-running.aspx
Best regards
Please remember to mark the replies as answers if they help, and unmark the answers if they provide no help. If you have feedback for TechNet Support, contact [email protected]

I have an IPad 2 and an Iphone4, but as it suggests that I can click a photo on my iPhone and the image will also reflect simultaneously on my IPad does not happen, though I have activated cloud on my iPhone. What could be the problem.???

I have an IPad 2 and an Iphone4, but as it suggests that I can click a photo on my iPhone and the image will also reflect simultaneously on my IPad does not happen, though I have activated cloud on my iPhone. What could be the problem.???
Also in my iPhone4 the photos that I have downloaded manually from my computer cannot be erased from the phone, how do i do this.???

Sounds like you are not running iOS 5 ..........
Update your iPad 2 to iOS 5............
I purchased an iPad 2 for my wife for Xmas and it did not come with iOS 5 so I had to update it......
http://www.apple.com/icloud/get-started/
http://support.apple.com/kb/HT4972

How can I install Firefox on a server that does not have an internet connection?

I run Firefox on a server to display graphs for a program. I was able to save, upload and install Firefox version 21 on my server because it used the executable installation program. Versions 22 and 23 use a stub program that goes to the internet and installs the program. My server does not have an internet connection, so the stub program does not work. Can I get a copy of the executable program that installs the program without having an internet connection?

hello pkautzman, the full install packets that are capable of an offline installation are available at https://www.mozilla.org/firefox/all/.

When trying to send E-mail via AOL i get the message "rejected by the server because it does not allow relaying" I have checked settings as per answers to similar question

When trying to send E-mail via AOL i get the message "rejected by the server because it does not allow relaying" I have checked settings as per answers to similar question

From which account does the email not send? When sending from an account, the iPad will first try to use the aoutgoing server for that account. If it can't it will try the other accounts listed.in the setting on the iPad for that account. It soulds like the server for the account is not working and that the alternate server is resjecting the messag since it did not originate ffrom the account associated with that server, That is to prevent sending spam.

Does Lion Server have bootcamp?

Does Lion Server have bootcamp? I'd like to ugrade my Mac Mini Server with Snow Leopard Server and my MacBook Pro with Snow Leopard to Lion but the install for the mac mini will be a pain to do Lion so I was thinking of doing Lion Server for both, so I don't have to pay for both Lion and Lion Server, but I'm wondering if I can do bootcamp since I couldnt' do bootcamp for Snow Leopard Server?

Hi
Have a look for yourself and compare the two:
http://www.apple.com/macosx/specs.html
Which is Lion and BootCamp is clearly listed:
http://www.apple.com/macosx/server/specs.html
Which is Lion Server. I don't see it so I doubt (just as in 10.5 and 10.6 Server) if Apple are going to make it part of OSX Server anytime soon? Still, you never know?
Prior to 10.7 you could download VirtualBox (it's free to download) and install 10.6 Server (and pretty much anything else but not OS X Client) quite happily:
http://www.virtualbox.org/wiki/Downloads
http://www.virtualbox.org/attachment/wiki/Screenshots/mac_os_x.png
This may still be the case with 10.7 Server? What you could try is install 10.7 Server, install VirtualBox and install 10.7 Server (again) as a virtualised server. Apart from licensing I can't see why this would not be possible? Why don't you give it a try and let us know how you get on?
HTH?
Tony

CSM(content switching module) supports the 2 tier server load balance ?

hi everyone,
Does any know the CSM support 2 tier server load balance ?
this means that CSM perform the server load balance for servers and the same servers require another time Server load balance. In the other word,
the CSM supports server port and client port for server load balance ?
thanks
fred.

Hi, this seems to describe a typical case of multi-tier design where the CSM needs to handle 2 types of connections:
1. clients->CSM->serverfarm1
2. serverfarm1->CSM->serverfarm2
We usually refer to the second type of connections as server-to-server load balanced traffic.
There is no problem in handling that scenario with the CSM and you have a few options.
In particular, each virtual server on the CSM can be configured to only accept incoming connections from a specific VLAN, so you can use that as an additional security measure or to distinguish connections based on which VLAN they come in from.
If you want to, you could even configure the CSM with 2 virtual servers with the same exact virtual IP and L4 port, but listening on 2 separate VLANs (the client-side VLAN and serverfarm1 VLAN) and use a different server farm based on that.
One important thing to keep in mind when handling server-to-server load balanced connections: if serverfarm1 and serverfarm2 are on the same VLAN, you have to configure "client NAT" for the server-to-server connections, to force the return traffic back to the CSM.

Control without client or middle tier server

Is it possible to remote control/view workstations without having the
client OR a middle tier server set up? We only want to be able to control
our workstations from inside our firewall, so the middle tier server
would not be needed.
Another question, is it also possible to run naldesk the same way to push
applications out to workstations without the client installed (with or
without the middle tier server). Thanks in advance.

Desktop4 can use any of the options.
It really is a bit cumbersome to use at the moment, but drop me a note at
my email address of craig_d_wilson at yahoo dot com in about 2 weeks.
I'm in the process of writing a small front-end program for use in
clientless environments. I should have something going by then.
Normally the Workstation Object gives rights to the local SYSTEM account
when the Novell Client is around to access NetWare shares.
In a Windows Domain Environment, you can use the Windows Domain workstation
object to do the same thing.
Otherwise you may have issues accessing system resources when process are
running in System mode.
FYI, you will 100% need a middle-tier server to get your App Objects.
It will not be needed to RC or transfer files, but you will need at least
one mid-tier server.
Craig Wilson
Novell Product Support Forum Sysop
Master CNE, MCSE, CCNA
http://www.ithowto.com
Editor - http://www.ithowto.com
<[email protected]> wrote in message
news:[email protected]...
>> Yes to all of your questions.
>>
>> In regards to remote control you have two options.....
>>
>> 1) Use Desktop4.exe with password based remote control to connect to
> the
>> remote PC.
>> 2) Have the remote PC use the option to Request a remote control
> session
>> from the support personnel.
>>
>> Search support.novell.com for desktop4.exe and there should be a couple
> tids
>> that go into detail.
>>
>> In regards to distributing applications.....................
>> 1) Are you in a Domain or Non-Domain environment. This controls what
>> options you have.
>>
>> --
>> Craig Wilson
>> Novell Product Support Forum Sysop
>> Master CNE, MCSE, CCNA
>>
>> http://www.ithowto.com
>>
>> Editor - http://www.ithowto.com
>
> Thanks for the response! We are currently strictly netware with no
> domain, but we were looking at moving towards a domain (we are testing
> both OES cores to act as a PDC to authenticate through edir, both of
> which we got to function correctly :-) So we were just looking at the
> rest of the stuff we may or may not lose by going that route. We
> currently use ZENworks mostly to remote view student workstations,
> control admin machines, and image all the machines. We also occasionaly
> push out small apps or registry changes with Nal, but not that often. Can
> you simply remote view the workstation (without the user knowing) or does
> desktop4.exe only control the machine? I will have to check it out.
> Thanks again

Reports Multi-tier server from Dev 2000:v 1.6.1 don't start on solaris 8

Reports Multi-tier server from Oracle Developer 2000:version 1.6.1 don't start on Sun Sparc Solaris 8, it writes:
Segmentation Fault (core dumped). What i have to do?

Reports Multi-tier server from Oracle Developer 2000:version 1.6.1 don't start on Sun Sparc Solaris 8, it writes:
Segmentation Fault (core dumped). What i have to do?

Spotlight or Find does not work with server

At work, anyone still using OS 10.3 can use find to find files on our server. Anyone using OS 10.4 in the office can't. When ever I search for something, it just spins forever while a coworker using 10.3 does the same search and if finds the file in a matter of seconds. Any thoughts on how to trouble shoot this problem?

Hi Preston,
Make sure users logging into the server have the correct permissions to read the folder, .Spotlight-V100, at the root level of the volume hosting the data on the server. OS 10.3 handles searching differently than 10.4 (Spotlight).
Best,
Sean

Google mail tells me that I have an outdated version of Firefox which it does not support. I have Firefox 8.0.1. Why is there a problem?

Google mail tells me that I have an outdated version of Firefox which it does not support. I have Firefox 8.0.1. Why is there a problem? I am using OSX 7.2
When trying to access the URL after startup or waking the computer, I get the following message
sec_error_ocsp_server_error
The I will get a message that my version of Firefox will not work with google mail.

You can check the OCSP settings.
*Firefox > Preferences > Advanced > Encryption: Certificates > Validation:
*[X] "Use the Online Certificate Status Protocol (OCSP) to confirm the current validity of certificates"
*[X] "Validate a certificate if it specifies an OCSP server"
*[ ] "When an OCSP server connection fails, treat the certificate as invalid"

Does Adobe Reader for iOS have the ability to open inbedded links to additional PDF docs? If not, then what would be the best way to use these already created PDF's?

Does Adobe Reader for iOS have the ability to open inbedded links created with Acrobat Standard to additional PDF docs? If not, then what would be the best way to use these already created PDF's on an I Pad?

driddy61,
As of June 2014, none of the Adobe Reader mobile products support the hyperlink action for opening a separate PDF document.
Adobe Reader for iOS
Adobe Reader for Android
Adobe Reader Touch for Windows 8
In addition, the Reader mobile products do not open multiple windows/documents simultaneously, which would make the navigation between PDF documents nearly impossible. (Once a hyperlink takes you to a different PDF document, you have no way to go back to the original PDF document.)
The only Adobe Reader product that fulfills your department's requirements is Adobe Reader XI (mostly for Windows/Mac desktop/laptop computers). Acrobat Pro and Standard are paid products.
Because you are in search of a less expensive device for your department, you could get a Windows tablet instead of a Windows desktop/laptop computer. Microsoft Surface Pro (that you've mentioned in your previous reply) is just one example. You can also find other less expensive Windows tablets.
Tablets
However, please keep in mind that there are two different types of Windows tablets running two different operating systems.
(a) A Windows tablet with an Intel-based processor running Windows 8.1 Pro
Example: Surface Pro 3
You can install and run traditional desktop apps (e.g. Adobe Reader XI) and new Windows Store apps ("Modern" or "Metro-style" apps).
(b) A Windows tablet with an ARM-based processor running Windows RT 8.1
Example: Surface 2
You can only install and run Windows Store apps (e.g. Adobe Reader Touch) but not traditional desktop apps like Adobe Reader XI.
In general, type (b) tablets are more affordable than type (a) tablets. However, if you want to run Adobe Reader XI, you do need to check the technical specification of each tablet and make sure the following conditions are met.
Processor: Intel
Operating system: Windows 8/8.1 or Windows 8/8.1 Pro, not RT
Hope this helps you choose the right device for your department. Please let us know if you have any questions about system requirements or supported features in the Adobe Reader products.

Does NET8 2-tier server have a simultaneous connection limit ?

Similar Messages

Maybe you are looking for