Dual boot Windows from Toshiba Recovery CD

Is it possible to dual boot Windows from a Toshiba Recovery CD?
I have a Satellite A45-S120 with a Toshiba Windows XP Recovery CD.
I have XP installed on one partition. I partitioned the hard drive using GParted, and installed Linux on several partitions. I want to install XP on a 2nd partition, so I can dual boot 2 versions of Windows from the same hard drive.
When I go to install Windows, the Toshiba Recovery CD says the entire hard drive will be deleted. Is this the case, or will it only reformat a partition? I went into GParted and was able to change the first Windows XP ntfs partition to hidden, and now successfully can not boot Windows from the Grub Boot Manager. However, I worry that if GParted can see the partition, then the Toshiba Recovery CD might be able to. In addition, the Linux ext partitions could not be set to hidden. Will the Toshiba Recovery CD overwrite all the partitions, or can it maybe only install itself on the one ntfs partition available?
I read at http://www.vistax64.com/general-discussion/193560-install-xp-toshiba-recovery-disk-d.html that there may be a way possible, any advice?
Specs are:
1.26 Ghz Celeron
1.256 GB Ram
40 GB HD

Satellite A45-S120
I want to install XP on a 2nd partition,
So far as I know, that recovery disc will install nothing. It will restore the entire hard drive (master boot record and all) by writing all the bytes that were on the original drive (byte-by-byte).
-Jerry

Similar Messages

Dual boot windows from USB via grub?

HI all:
I recently had a motherboard failure on an existing PC on which I dual-booted Windows XP and Gentoo. I replaced that box with a new HP PC preloaded with Vista. Wiped that immediately, and installed ARCH. But, I would like to also boot XP, and, since my old hard drive is still OK (I have it in an external USB adapter), I was thinking that I might configure grub to point at an external USB drive like this:
# Windows XP
title Windows XP
root (hd1,0)
makeactive
chainloader +1
where "hd1" (I hope) would point at my old drive, now connected via USB. In this way, I am really booting from my HDD (where grub lives), but "chain loading" from my USB external. Can this work??
-dvh

dvh wrote:
I configured as shown in the wiki, but when I try to boot XP, I get a message that says something to the effect of "missing or corrupted <windows root>\system32\ntoskrnl.exe". I checked the disk and it seems to be there and OK. I get the feeling that it is either NOT finding the hard disk (or partition) or it cannot interpret the NTFS file system (but grub was able to boot this before,...). So, two questions...
1) how do I know what the designator for the external USB hard disk will be? I have speculated that grub will find it at "hd1", but maybe not?
2) does the target disk NEED a windows boot loader? as I said earlier, I used to dual boot it, so there is a grub loader on that disk also.
...ok, three questions...
3) anything else that I should consider??
Thanks again for any help.
-dvh
1) i don'tknow a way to check this, but the
missing or corrupted <windows root>\system32\ntoskrnl.exe message comes from the windows boot process,
so it seems grub is configured correctly.
The main problem is that BOTH grub and windows boot need to have the correct settings.
Windows takes the settings for boot from the boot.ini file in the root of C:\ , and that probably needs to be changed.
You will need some way to get read/write access to the windows C-drive partition.
Install ntfs-3g in archlinux (see NTFS_Write_Support ) and post the contents of boot.ini .

Dual Boot Windows XP Downgrade Recovery

I purchased a Thinkpad R500 with XP preinstalled. It came complete with recovery CD's, but for Vista.
I would like to create two partitions, one with a minimal/cutdown XP (for audio production) and normal XP partiton for web browsing and working with office software.
From what I have read I should be able to create XP boot CDs in Rescue and Recovery (by pressing the Thinkvantage button). I have R&R 4 installed in German, but there is no option to create a boot CD.
As I do not have recovery disks for XP, or can not create them, how do I accomplish this?

Alphajuno, welcome to the forum,
in order to create recovery discs you need to go to; Start > Programme > ThinkVantage > Create Product Recovery Media.
Hope this helps
Andy ______________________________________
Please remember to come back and mark the post that you feel solved your question as the solution, it earns the member + points
Did you find a post helpfull? You can thank the member by clicking on the star to the left awarding them Kudos Please add your type, model number and OS to your signature, it helps to help you. Forum Search Option T430 2347-G7U W8 x64, Yoga 10 HD+, Tablet 1838-2BG, T61p 6460-67G W7 x64, T43p 2668-G2G XP, T23 2647-9LG XP, plus a few more. FYI Unsolicited Personal Messages will be ignored.
Deutsche Community Comunidad en Español English Community Русскоязычное Сообщество
PepperonI blog

I want to dual boot Windows 8 on my 20-inch, Mid 2007 iMac, from an external USB drive.

I want to dual boot Windows 8 on my 20-inch, Mid 2007 iMac, from an external USB drive. The internal drive is completely dead, it doesn't even show up in Disk Utility. I'm running 10.8.2 from the external drive. When I start Boot Camp Assistant, at the Introduction page, when I press the continue button nothing happens. Do I have to have internal drive to run Boot Camp Assistant? Can anyone provide me with the steps to dual boot, with his setup? Thanks in advance!

Hi maczimillon,
Only follow these steps, it works for my:
Open "System Information" and note your "Boot ROM Version" (some like MBP51.007E.B06)
Navigate to "Utilities" in Finder and open the package contents of -BootCampAssistant.app- with right click. Duplicate the "Info.plist" file to the Desktop e.g. and open that with Text Editor.
You must locate the keys "DARequiredROMVersions"and "USBBootSupportedModels"
Add new strings with the information of your machine under booth keys (step 1), always respect the format, such as: <string>MBP51.007E.B06</string> for the frist key and <string>MBP51</string> for the second key.
Save changes and replace the original plist file (it may ask you to enter admin pass)
If you proceeded correctly you will see the checkbox "Create a Windows 7 USB install disk" enabled in Boot Camp Assistant.
Then you can follow the usual Boot Camp installation using your WIN8 DVD iso image . The assistant program will proceed resizing your disk partition and installing necessary drivers for your iMac.
I strongly recomends you to use thirld party's bootloaders like rEFInd (rEFIt) because of the Apple SMC versions of some old machines should not be able to boot properly from external devices like USB drives.

Dual boot Windows 7 and Arch from 2 seperate drives (UEFI)

Hello everyone, I've been working on installing Arch to a secondary hard drive for the past few hours, but I am trying to make sure I won't mess up my Windows 7 install. I have found several topics talking about dual booting Windows 7 and Arch, but not a whole lot on booting them from separate drives. My drives are currently setup as follows.
sda (120GB SSD for Windows 7)
sda1 (100MB System Reserved NTFS partition)
sda2 (Windows 7 install)
sdb (1TB HDD for Windows programs, files, etc)
sdb1 (1TB NTFS partition)
sdc (1TB HDD)
sdc1 (boot 512MB FAT32)
sdc2 (root 500MB ext4)
sdc3 (home 300GB ext4)
sdc4 (swap 10GB)
rest unallocated "free space"
I used Gparted to create the partitions. I ended up getting hung up on the "Create Filesystems" sections, specifically this line"
# mkfs.fat -F32 /dev/sdXY
Now that I am looking at it, I'm thinking the "Create Filesystems" section maybe isn't necessary because I've used Gparted?
If it isn't necessary, when I get to the "mount the EFI System Partition to /boot" section, would I simply use
# mount /dev/sdc1 /mnt/boot
instead of
# mount /dev/sdXY /mnt/boot ?
The way I had this setup with Ubuntu was 3 partitions on sdc (/, home, swap) and I set my PC to boot to the sdc drive on startup. The boot loader would then give me the option to boot into Ubuntu or Windows 7, and I never had to alter the sda or sdb drives at all. Is this possible through Arch? My thinking is that even if it isn't, I should still be able to enter the BIOS boot menu and select which drive to boot manually correct? That wouldn't be too big of a deal for me because I spend 90% of my time in Linux, and only use Windows for Photoshop and gaming occasionally.
Thanks for taking the time to read this. I would have just tested this out, but I am afraid of messing up my Windows install.

After several sleepless hours I had to give up and go to bed about 5 hours ago. The installation process went smoothly (or so I thought). I followed the tutorial closely and upon rebooting I was met with a blinking cursor. After some googling I found others who said I should press TAB, but nothing seemed to work.
I rebooted to the iso disk and found the "boot installed OS" option and noticed it said "Press TAB to edit". I then found the boot parameters and tried everything from hd0 0 to hd4 4. I believe I have Grub setup correctly because every option besides hd0 0 either says "Booting..." and then gets stuck, or says "That disk and partition combination does not exist". So yea, I think hd0 0 is the correct boot path, it just gets stuck with the blinking cursor.
silverhammermba wrote:
You have the right idea. You want to install a bootloader on sdc1 which will be able to boot both Arch and Windows.
Your best bet would be to use something like rEFInd. It has a "scanfor" option that should automatically detect your BIOS-configured Windows installation and add a boot option for it. Note that depending on your motherboard, you may have to switch to UEFI-only mode and Windows will be unbootable without the assistance of a UEFI program which is backwards compatible with BIOS (like rEFInd).
Thank you for the link. Considering I can't get into my install and the actual install only took about 30 minutes, I think I am going to just start from the beginning again with REFIndr. It seems much simpler. I only used Grub because I've used it before with Ubuntu, but my very limited knowledge is telling me Grub is probably the problem.
MoonSwan wrote:Just an idea: My bios has a "Boot-up Prompt" which I can invoke when it's POSTing by hitting F11. This brings me to a menu that allows me to choose which drive I want to boot up that day. I use it when Syslinux isn't working properly (Which is right now as a matter of fact ...) in order to boot Windows so I can do some SCII, for example. I, too, dual-boot but I have both OSes on different SSDs. So my 120GB Crucial SSD has Arch on it and the 240GB Kingston has Windows, SCII, Portable Apps, etc and nary the two shall meet. It makes dual-booting easier in the case of a corrupt OS or MBR or what-have-you. You may want to give your Bios a better look to see if you can do the F11 trick. It probably can and will usually tell you so at POST by printing that information on-screen along with your drives-detected and other messages (I hit Pause sometimes to read all the POST messages).
This is exactly what I was talking about doing when I mentioned:
My thinking is that even if it isn't, I should still be able to enter the BIOS boot menu and select which drive to boot manually correct?
That's good to know, because even if this next install doesn't work I think if I pull the other drives I should be able to get it working fairly easily.
Thanks again everyone.

Re: Tecra S11 - Dual boot Windows 7 and XP

I have installed Windows 7 (from the hidden recovery section of the hardrive) on my new Tecra S11. I would like to know whether I can use the Windows XP
recovery media provided by Toshiba to create a dual boot Windows 7/Windows XP rather than reverting to XP?

You can create dual boot but not using two recovery images. Recovery image can be used for first OS installation. You cannot define on which partition the recovery image will be installed. It will always be installed on first partition.
I recommend you to do follow:
-at first install WXP using original Toshiba recovery disc
-Windows 7 install using Microsoft installation disc
I have done the same on my Satellite A300.

Y500 dual boot windows 8 and fedora 19 problem

I bought a y500 two days ago and i wanted to dual boot windows 8 and fedora 19, so here's what i did
1. downloaded fedora 19 (x64) iso from the fedora website.
2.made a live USB using live usb creator.
4.opened disk management utility and shrunk the c drive (windows 8 was installed here) by 100 gb and kept the 100gb unallocated.
3. started the laptop with novo button, changed the bios config to boot from usb.
4.installed fedora from usb, selecting the 100gb unallocated memory for installation
5.restarted the laptop.
now the problem is fedora works perfectly but when i try to boot windows 8, the following error is shown.
windows failed to start
file:\BOOT\BCD
status: 0xc0000225
info:the boot configuration data for your PC is missing or contains errors.
i am guessing the fedora installation overwrote the boot files of windows and
i have not taken a backup. please help

hi,
I have a Y500 and I wanted to dualboot fedora 19 with windows 8, this proved to be unsuccessful. I had made a repair disk before the process (but not a set of recovery disks unfortunately >.< ). now I inserted the repair disk and selected the automatic repair option, it showed a message that auto recovery has failed. now when I pressed the NOVO button and selected the system recovery option, it does not go into the OKR menu but continues with the normal booting process. Can somebody guide me or give links where I can find step by step instructions to making OKR work and reset my laptop to factory settings? PLEASE help As Soon As Possible
NOTE: I did resize the windows 8 os partition but the recovery and the lenovo partition are still untouched

Lenovo C340 i3 System - Dual boot windows 7 / 8 cant load windows 7 please help

Hi there
I have a lenovo c340 all in one pc the i3 processor type which came with windows 8
I have purchased a new hard drive and would like to dual boot windows 7 and 8
I have tried to install windows 7 and the system hangs before I even get into any configuration however windows 8 loads fine
I have looked in the bios and the system is showing windows 8 . has lenovo locked the bios to allow windows 8 only ?
Is there a way to load windows 7 onto the system ?
I really want to dual boot and have downloaded all of the drivers for windows 7 but for the life of me I can not get past the initial boot screen of my windows 7 disc
Can anyone help please

hi botards01,
If you're planning to use linux occasionally (Ubuntu for example) and you don't want to risk losing the One Key Recovery functionality, try to install Ubuntu via Wubi as this doesn't repartition your HDD but creates a virtual disk on your current OS.
Check it out - Install Ubuntu in Windows With Wubi
Hope this helps
Did someone help you today? Press the star on the left to thank them with a Kudo!
If you find a post helpful and it answers your question, please mark it as an "Accepted Solution"! This will help the rest of the Community with similar issues identify the verified solution and benefit from it.
Follow @LenovoForums on Twitter!

How to best partition the HDD for dual boot: Windows 8 & Linux

Hi,
I'm a newbie in Windows 8, linux, Partition....
I would like to use my new laptop with windows 8 pre-installed to the following:
Create a Dual Boot Windows 8 / Ubuntu
Create on my C drive (unique drive on my laptop):
*a partition for the system
*one for Windows 8
*one for Data and
*last one for Ubuntu OS
My aim is :
-to install VmWare on Windows 8 and run Checkpoint Splat with virtual machines to perform CCSA labs.
to install GNS3 on Ubuntu for CCNP labs but with GNS3 accessing files in the Data partition
I have a Toshiba Satellite with 750Gb and 8 Go RAM.
According to you what's the best size for my partitions?
Is there a better way to partition my C drive regarding my aim?
Best Regards
***I don't know if it's the right section, sorry for that. Feel free to move this thread in the appropriate section***

Hi,
Thank you all,
Isn't it too much 200G for Windows as i will on ly install VMWARE Workstation 9 for lab purposes and possibly a few softwares.
VMWARE installed on Windows will require 2 GB + 1 GB per host (i will use approximatively 15 hosts).
Checkpoint products will be installed on VMWARE that is installed in Windows :
- disk space needed for 3 Checkpoint gateways: 3*37 GB
- disk space needed for 2 Checkpoint gateways management servers: 2*10 GB
On Linux I'll install GNS3 with 10 GB disk space required and a few softwares.
I've got a Toshiba stellite computer with Windows 8 pre-installed.
Processor: Intel(R) Core(TM) i5-3210M CPU @2.5 Ghz
RAM: 8 Go
64 bits OS, processor x64
See below the screenshot
I've taken screenshot of my partition (below).
* Don't take into account the disk 1 (E) partition
Can u confirm that in Disk o, partitions with 450 Mo, 260 Mo and 9.48 Go are for recovery system?
I am planning to let the recovery partition as it is and divide the TI30985500A (C) partition (688 Gb) into:
- 200 Gb windows partition
-100 Gb Linux partition
-388 Gb data partition
What do you think about this partionning regarding the informations i've provided above?
Greets

Dual boot Windows 7 partition help

I want to dual boot Windows 7 & arch but I need help with figuring out what partitions to make and where to put them because it seems the automatic partition-er won't do the trick for me.
I have two drives that I want to completely format for a fresh, clean install: a 60GB SSD & a 750GB hard drive. I want the end result to be that the SSD only has Windows 7 Pro x64 SP1 installed to it and I will point the 'My Documents', 'My Pictures', etc. to a NTFS partition on the hard disk drive ( I know how to do this folder pointing ). I don't want arch to touch the SSD if possible so I can reformat the SSD separately if I ever just want to reformat Windows. I only want arch to be on the hard disk for that reason. I don't think I care which one handles the OS switching at boot ( should I favor Windows MBR or syslinux? Please give advice. ) And I would assume I make the NTFS partition on the hard disk a primary partition so how do I split up arch for the 3 other primary partitions left since the auto partition from the arch boot CD uses 4?

I'm no expert, but the way I would do it would be like this:
1. Create partitions on the HDD for /, /boot, /home and swap, along with one (or more) for your Windows personal files
2. Set the BIOS to boot from the SSD.
3. Install Windows on the SSD.
4. Right-click the "My Documents" folder, select "properties", then the "Location" tab and choose the new location for the folder.
5. Install Arch on the HDD partitions, and allow the boot manager to install itself in the MBR of the SSD.
Then the whole boot process will be on the SSD... If you ever need to get rid of the Linux bootloader, you can overwrite it with a "clean" Windows one using bootrec.exe (see here: http://support.microsoft.com/kb/927392).
Last edited by esuhl (2012-03-26 04:52:12)

How to dual boot window 8.1 64 bit with xp sp1?

Hello Hp PC Experts,
Sir i was bought HP 15-r119TU two week ago. So i face problem of dual boot with this HP note book. I need dual boot window 8.1 64 bit with XP SP1. Kindly help me at the earliest possible.

@mp56
‎Thank you for using HP Support Forum. I have brought your issue to the appropriate team within HP. They will likely request information from you in order to look up your case details or product serial number. Please look for a private message from an identified HP contact. Additionally, keep in mind not to publicly post ( serial numbers and case details).
If you are unfamiliar with the Forum's private messaging please click here to learn more.
Thank you,
Omar
I Work for HP

Dual Boot Windows 8 & 7 Help On HP Pavillion G9-1178CA

Hello Guys I Just Need Some Help From You Guys So when I Try To Dual Boot Windows 7 & 8 it says that this partion is dynamic or something like that
And i do not have ubuntu Dual booted so please help me thank
-Sam

Hi,
To rebuilt boot loader, I suggest we can try following command when you enter Windows 8.1.
Run cmd as administrator and type following command:
BCDboot [Partition Letter with windows 7 installed]:\windows
Note: if you installed Windows 7 on Partition F, the command can be write as: BCDboot F:\windows.
Then, restart and boot into Windows 7.
What’s going on?
Kate Li
TechNet Community Support

[SOLVED] dual booting windows 7 with btrfs on grub-bios -- core.img

I am trying to install arch in a dual boot configuration with an existing windows 7 partition. I have everything from the beginner's guide done but the bootloader. When I run grub-install it tells me that core.img is too big.
Some googling tells me that this is relatively common with btrfs, and it seems the only work around is to switch to gpt mode and use a grub bios partition. But the info I've seen indicates that I need to use MBR mode to dual boot windows.
Is it safe to do this with windows? Is there another workaround? Or will I have to settle for ext4?
Last edited by jorenko (2013-06-09 03:53:24)

Well there's your problem, your first partition starts at sector 63. With recent versions of windows and fdisk (and every other partitioning tool I can think of off the top of my head) things now align themselves correctly. Also because there is now GPT, the first partition typically starts later as the GPT partition table will typically sit between the MBR and the first partition.
On a MBR partitioned system, grub2 will actually use the first 446 bytes like normal, but will then also use the space that is empty where GPT would sit. This is why when you have a GPT partitioned system, it will require you to create a 1-2MB grub boot partition, as it needs somewhere else to put its bloat. GPT actually still uses the MBR section, but simply creates one large partition covering the whole disk. This is so that tools that are not GPT aware will not think that they have a whole free disk to use as they please.
For comparison, here is whe I get from fdisk:
# fdisk -l /dev/sda
sudo fdisk -l /dev/sda
[sudo] password for curtisshima:
WARNING: fdisk GPT support is currently new, and therefore in an experimental phase. Use at your own discretion.
Disk /dev/sda: 250.1 GB, 250059350016 bytes, 488397168 sectors
Units = sectors of 1 * 512 = 512 bytes
Sector size (logical/physical): 512 bytes / 512 bytes
I/O size (minimum/optimal): 512 bytes / 512 bytes
Disk label type: gpt
# Start End Size Type Name
1 2048 2099199 1G EFI System EFI System
2 2099200 252166798 119.2G Linux filesyste arch-btrfs-1
3 252168192 488397134 112.7G Linux filesyste arch-btrfs-3
Note that I do use GPT. But that is not the point here. What I am trying to show is where my first partition starts. This is also where fdisk will start partitions these days. This is to ensure compatibility with 4k advanced format disks.
If you are not dead set on Grub2, you could try using syslinux. I really like it much better, though if you are booting more than one Linux, you need to either employ chainloading to various partition boot records, or have a shared /boot. Having a windows partition doens't really matter, as you are simply chainloading to that funky reserved partition anyway.
The other option is to use grub-legacy, which can still be found in the AUR. I actually liked the orginal Grub, as it provided a nice feature set, but was still configurable by hand and it actually fit into the MBR.

[SOLVED] Dual boot windows 7 and arch Linux with seperate hard drives

Ok so I'm stuck trying to get my computer to dual boot windows 7 and arch. They are installed on different hard drives and I have grub 2 as the boot loader. I can't find any tutorials on how to do it with seperate hard drives I know how to do it if they are on the same hard drive. Also I want windows on the "first" hard drive how do I check to see which one it considers the first?
Last edited by bdawg (2012-09-21 23:15:37)

DSpider wrote:
drobole wrote:If you want to change it so that sda becomes sdb and sdb becomes sda, you should be able to do that in BIOS.
Not from the BIOS. He would need to physically open up the computer and switch the cables between them (or add another drive).
There's no actual performance increase in changing this order. Performance increase is when you have the partitions as close to the beginning of a HDD as possible, where the platters spin faster (basic mechanics, not to be confused with CD/DVD, which are being written from the inside-out to prevent errors after extended usage), and it especially doesn't apply to SSDs whatsoever.
You may be right about that. I remember I had to do this a while back but I probably switched the cables. It also messed up the drive mapping in Windows 98 if I remember correctly.

Dual booting Windows 8 and Arch Linux with UEFI

Hi all!
I'm trying to install Arch Linux on my computer where I already have Windows 8, and I'm getting a little stuck when it comes to the partitioning.
Following the beginner's guide and the method here: https://wiki.archlinux.org/index.php/Un … n_in_Linux for setting up the partitions properly, regarding UEFI. My problem is that when using cgdisk to set up a new EFI system partition (ef00), I get an error message when trying to write the partition table (just saying that something went wrong). I figure the problem is that I already have a partition like this (correct me if I'm wrong), but it really looks like it succeded (see info below). So my question is: How do I preceed to keep my Windows 8 installation happy, but installing Arch? Do I remove the old EFI system partition and create a new one, or is there some method that allows me to edit the already existing one, to allow me to dual boot Windows 8 and Arch?
My partition table now looks like this:
Part. # Size Partition Type Partition Name
1007KB free space
1 500MB Windows RE Basic data partition
2 300MB EFI System EFI system partition (this one was already present on my system)
3 128MB Microsoft reserved Microsoft reserved partition
4 63.5GB Microsoft basic data Basic data partition
8 512MB EFI System EFI System partition (this is the one I tried to create when I got the error message)
5 29.5GB Linux filesystem Arch (this is where I was going to put my Arch installation)
6 22GB Windows RE Basic data partition
7 1024MB Windows RE Basic data partition
615KB free space
Just for the record; I only created partition #8 and #5.
Any help is appreciated! And sorry for beeing a total noob, but I really suck at this.

sudo make sandwich wrote:If it is possible to share ESP between OSes, how do I do this (would it be sufficent to follow this section: https://wiki.archlinux.org/index.php/Beginners'_Guide#For_UEFI_motherboards)?
There's really very little to do to share an ESP between OSes. Most OS installers will auto-detect the ESP and use it. Problem solved. For Arch it may be a bit more effort just because Arch uses a more hands-on installation process, but I've only done a couple of Arch installations, and the last one was several months ago, so I don't recall the details clearly enough to comment.
And how big will the partition need to be? The beginner's guide says 512MB or higher.
I don't know what was in the mind of the author, but my guess is that's because that's roughly the cutoff point where mkdosfs starts creating FAT32 by default rather than FAT16. The ESP is officially supposed to be FAT32, not FAT16, although FAT16 usually works OK. It's also possible to create FAT32 on smaller partitions by using an explicit option to mkdosfs ("-F 32").
The optimal size of the ESP depends on the files stored on it. If you don't store your Linux kernels, something as small as 100MiB is usually adequate; but a few Linux kernels and their initrd files can consume twice that amount. My own recommendation is for the ESP to be 200-500MiB.
The only error message I got from cgdisk is "Problem saving data! Your partition table may be damaged!", however booting Windows again works fine. Parted did not complain about antything.
Use the "verify" function in cgdisk. That will reveal any problems with the data structures. If a verify turns up OK, then that means that cgdisk ran into some sort of disk problem. Running gdisk rather than cgdisk and using the gdisk "w" option (without making any changes) may produce a more helpful error message.

Dual boot Windows from Toshiba Recovery CD

Similar Messages

Maybe you are looking for