DW CS3 preview issue after installing Vista SP2

I have DW CS3 installed on my desktop and laptop computers. One computer uses vista64 and the other vista32. After installing vista service pack 2, I now have the following issue previewing PHP pages under Apache: All browsers give me a "cannot display the webpage" error UNLESS I am connected to some kind of network--it could be the internet or my peer-to-peer network. My destop computer is attached to a printer via RJ45 cable. If the printer is turned on, I can preview webpages in DW. If the printer is turned off, I cannot! Or, if I am connected to the internet through my wireless internet card, I can preview pages, otherwise, not.
Previous to installing SP2, I was able to preview pages on both computers without the need to be connected to a network, so I am pretty sure that SP2 is involved in this new issue.
When Apache and MySQL start up in the XAMPP control panel, there are no errors, and I can go into PHPMyAdmin just fine.
Has anyone else run into this? Any thoughts?

I'm just following up here. I have not solved the issue, but I did figure out that the problem isn't with vista service pack 2 but with Kaspersky anti-virus 2009.

Similar Messages

  • No Sound After Installing Vista SP2

    I installed with Vista SP2 update yesterday and now I have no sound. It seems to be a driver problem but updating the driver does not fix it. There is a red "x" by the speaker icon on the task bar and the volume buttons on my keyboard dont work.
    The Conexant HD audio driver says that it is installed properly but I have no volume.
    Microsoft seems to be aware of this problems and has a few fixes out (like http://support.microsoft.com/kb/948481/) but nothing they have published is helping me.
    Please help as I really need to have my sound up.

    This message can be closed - though, not sure if I am able to do myself.  I uninstalled the IDT Codec, did a full shutdown, then started back up, let windows fully load, was prompted for installing of the Codec by Windows, clicked to allow the installation to occur and the codec/driver was successfully installed.  I have my sound back!   Fantastic!

  • Satellite L300 (PSLB9A) - No internet access after installing Vista SP2

    Just upgraded my Vista with Service Pack 2 and found that I cannot connect to any internet sites, have proved it is SP2 by rstoring to prior SP2 and all is OK, also reloaded the OS with my recovery disks and all works OK...... ....until I load SP2 then when I try to access the internet I cannot, getting "IE cannot display the webpage".
    Diagnostics report no problems found. This happens with either IE7 or IE8, firewall is disabled and I can reach any network device including my server but am unable to load the server web page, same issue..
    Any assistance would be appreciated.
    Pete

    Hi Sascha
    Yes I rolled it back to SP1 last night as I could find no way to fix the problem, I've never seen this before. Anyway all now works OK with SP1, before I rolled back I also rolled back IE8 to IE7 (no change) and removed, one by one the updates post SP2 install (also no change), as soon as I had rolled back to SP1 all worked fine, can get instant internet. I am going to load IE8 tonight and see if that works OK.
    As for Skype MSN, no did not try those while SP2 was loaded, should have tried my skype account.
    Any thoughts?

  • Issues after installing Classic on OS 10.4

    Background and System
    I have a Power Mac G3 350Mhz Rev 2 Blue and White, 512MB, 40GB, DVD ROM
    running 10.4.9 installed from Retail DVD. Firmware up to date. 2x 20 GB partitions formatted as Extended
    Prior to this issue OS X has been running well.
    Issue:
    After installing OS 9.2.1 to second partition OS X will now not boot up from DVD nor it's partition
    Solutions tried:
    I wanted to install a Classic environment so used a Retail OS 9.2.1 Bootable CD and did a full install to the second partition.
    After the install finished and the system restarted, set on the OS X (Partition1) for start up the system hangs right after the Apple "Chime". with no signal to video card
    Attempted to then boot from OS 10.4 DVD but this does not get detected when holding "c" down for boot up from CD option. This worked perfectly before.
    Have run OS 9.2.1 Disk Aid Verify and both partitions are ok. The system will boot from the 9.2.1 CD and partition but anything to do OS X now will not work. I also tried an Ubuntu 6.06 Live CD but this will not now boot either.
    Checked firmware and tried to re run firmware update and this advised my firmware was up to date.
    Any other suggestions?
    Thanks

    The only thing I can think of is that when you installed the 10.4.9 OS you didn't option to install OS 9 drivers.

  • Having issues after installing Essbase V9.3.1,configuring the SQL interface

    I am having issues after installing Essbase V9.3.1 and configuring the SQL interface. we are using UNIX/AIX box for our Essbase server and UDB DB2 9.1 SP6 as our SQL Interface.
    When tried to run an ESSCMD script to perform BUILDDIM operation on Essbase application using the load rule (with the SQL interface), got the error as recorded in the application log file and is attached at the bottom and the .odbc.ini file on the server looks as follows.
    Can somebody tell me whether .odbc.ini needs any correction or what else should I do to correct the issue and able to work thru using SQL interface? Appreciate any help provided in this regard. Thanks,
    .odbc.ini
    [ODBC Data Sources]
    DOLU003=IBM DB2 ODBC DRIVER
    [DOLU003]
    Driver=/home/db2inst1/sqllib/lib/libdb2.a
    Database=DOLU003
    [ODBC]
    Trace=0
    TraceFile=odbctrace.out
    InstallDir=/home/db2inst1/sqllib/odbclib
    [Mon Apr 20 15:16:29 2009]Local/New_Bud/Budget/Olapadm/Info(1021020)
    Cannot read SQL driver name for [] from [home/hyperion/.odbc.ini]
    [Mon Apr 20 15:16:43 2009]Local/New_Bud/Budget/Olapadm/Info(1013091)
    Received Command [SQLRetrieve] from user [Olapadm]
    [Mon Apr 20 15:16:43 2009]Local/New_Bud/Budget/Olapadm/Info(1021020)
    Cannot read SQL driver name for [] from [home/hyperion/.odbc.ini]
    [Mon Apr 20 15:16:43 2009]Local/New_Bud/Budget/Olapadm/Info(1021004)
    Connection String is generated
    [Mon Apr 20 15:16:43 2009]Local/New_Bud/Budget/Olapadm/Info(1021041)
    Connection String is [DSN=DOLU003;UID=...;PWD=...]
    [Mon Apr 20 15:16:43 2009]Local/New_Bud/Budget/Olapadm/Info(1021006)
    SELECT Statement [SELECT * FROM DB2OLADM.BD_DIMENSION_DEF_PC WHERE DIMENSION_ID
    = 12 ORDER BY TREE_NODE_NUM, PARENT_NODE, CHILD_NODE] is generated
    [Mon Apr 20 15:16:44 2009]Local/New_Bud/Budget/Olapadm/Info(1021013)
    ODBC Layer Error: [7] ==> [[DataDirect][ODBC 20101 driver]6013]
    [Mon Apr 20 15:16:44 2009]Local/New_Bud/Budget/Olapadm/Info(1021014)
    ODBC Layer Error: Native Error code [0]
    [Mon Apr 20 15:16:44 2009]Local/New_Bud/Budget/Olapadm/Error(1021001)
    Failed to Establish Connection With SQL Database Server. See log for more information
    --------------------------------------------------------------------------------------------------------------------------------------------

    I had similar errors when first setting up the SQL interface. Are you on a 64 bit operating system on the essbase server? If so Essbase needs to use the 32 bit odbc driver, not the default 64 bit driver.
    The 32 bit driver is still available here SysWOW64\odbcad32.exe <-----This is the 32 bit (Use)
    The Administrative tools by default uses system32\odbcad32.exe <----This is the 64 bit (Don't Use)
    Once I opened the 32 bit driver interface directly and set it up the errors went away.

  • Dreamweaver CS4 having issues after installing PS CS6 Beta

    Hi All,
    I'm having issues with Dreamweaver CS4 after installing Photoshop CS6 Beta. I'm getting the follwing erros when trying to open any html file (see attached image).
    Once I click OK, the file will open, also now; any copy and paste commands will not work. Anyone else experiencing any problems with other apps after installing this beta version?
    Any help and feedback is much appreciated, thanks!

    Re :Re: Dreamweaver CS4 having issues after installing PS CS6 Beta
    Just a thought ...
    This may help!
    Uninstall the Beta Version of Photoshop CS6 now and then restart your computer and see if that works.
    Open the CS4 programs and see if that fixed the problem and it is all working as it should again.
    It is worth a try!
    All the best.

  • No Wireless or Ethernet Driver After Installing Vista Ultimate on New Mac

    After installing Vista Ultimate 32 bit on my 17" 2.6 GHz MacBook Pro (486 gb hard drive, 101 gb bootcamp partition), (4 gb ram) The Vista Installation has no Driver Listed (or connectivity) for either the Apple Wireless or Ethernet drivers.
    Any thoughts?

    Did you install the drivers from the computer's software install DVD?
    Please post further questions regarding Boot Camp in the Boot Camp forums:
    http://discussions.apple.com/category.jspa?categoryID=237

  • Issues after installing Mavericks

    I am having a ton of issues after installing macericks on wed evening, on my MBP 15" 2.5 GHz i7 with 8GB of memory,
    I have a task com.apple.internetaccouts, and com.apple.MailServiceAgent, taking upwards of 100% CPU at time and the fan will go full speed, and earlier today i had a msg come up that i had run out of usable memory and the sytem had paused programs, I have restarted a few times and still the same things are coming up and the system has become really slow.
    would think that with this system not being that old, that i should not be having these types of issues, if there is something that someone could lead me to ths casue i thnk you
    Thanks
    Doug

    Had this issue again today on my wife's iMac.  This was after the Mail.app update that was recently released.  I now have messed with this issue enough that I believe I have figured it out.
    I used to have a plugin for Mail called HTTPMail that was used to access Hotmail prior to them having POP/IMAP.  It seems that removing the account from Mail left some residual account details in the ~/Library/Mail/V2/MailData/Accounts.plist file.  Mavericks Mail.app chokes on this account detail and starts duplicating it numerous times.  That's why the Accounts.plist file grows so large.
    If you open the Accounts.plist file in a text editor (TextWrangler would be my suggestion), find any <dict> entry that points to services.msn.com in any way and remove all those <dict>...</dict> entries, it should resolve the issue.  Warning though - I had to delete hundreds of entries so it took a while to do.  Once I finished it though, my wife's e-mail has been working fine.

  • Anyone else having battery life issues after installing Lion?

    Anyone else having battery life issues after installing Lion?

    Blue Sun Wing wrote:
    I have 7.1
    I think I would like to uninstall Lion as well.  I'd rather have my battery life back.
    See if this is helpful: http://www.iphone-my.com/mac/downgrading-lion-snow-leopard/               

  • CSM 3.3.1 - deployment bug? after installing SP1&SP2

    Hi all,
    I've recently installed CSM 3.3.1 with SP1 and SP2 and I've encountered quite serious (for me) problem. Has  anyone met strange situations after installing service packs?
    When I discover new device (i.e. router with 15.1 ios version) and make changes in ZBF policy, CSM deploys new configuration and everything seems to be fine. I must stress that only seems.
    When for example I want to make only small changes to that device (by adding new username ans password) I make "preview configuration" and I see that CSM deletes part of ZBF policy - 10 of 12 zone-pair. For example for some reasons manager makes "no service-policy ...." in zone-pair. When I do another "preview configuration" (after adding another username) it deletes those empty zone-pairs. I thoung maybe naming doesn't suit it and I need to recreate all policy through CSM - nooooo. It did not help. Still it tried to delete some of policy.
    Even when I created all ZBF policies from CSM Ive got situation when in one preview config it removes security-policy from zone-pair and after deployment in second preview it adds these security-policies to previous zone-pair. Its happaning in a  loop.
    Or another strange behaviour is when I add new username it does sth like this:
    In "preview configuration" there is
    policy-map type inspect CSM_ZBF_POLICY_MAP_1
    no class class-default
    class class-default
        drop
    while in GUI in CSM there is action inspect defined.
    I've looked through bugtool, but with no success, so need any help.
    regards

    hi,
    thx for interest,
    I didn't open the TAC case casue I didn't have much time for it, however the issue is resolved. It occured that SP2 to CSM was problematic. Right now I've got 3.3.1 version with SP1 and everything works just fine. To make sure that it was it, I installed then SP2 and the problem started again.
    I don't have configuration saved but actually there wasn't much of it. It was a fresh system and only 1 or 2 devices ware added so I suppose it should be easy to restore the situation.
    if you got any new info please let me know
    regards
    Przemek

  • MANY issues after installing Windows XP Home Edition with Boot Camp

    I have been having a lot of problems after installing Windows XP Home Edition (2002).
    For one, after installing Windows using Boot Camp with Mac OS X 10.5.1, I opened Windows on my Mac Book, inserted the Mac OS X Disk 1 as in the instructions and got the message: "This package requires a newer version of the Windows installer. Do you want to update the version of the Windows Installer on your system?" When I clicked Yes (I had NO idea what it meant at the time), I got the message: "The required resource 'UPDATE' is missing" and the Installer quit.
    How do I fix this problem?
    Another problem I have is that there is no sound on the Windows XP, yet it works perfectly on Mac OS X. Is there any way to fix this problem?
    A third problem I have is that I can't wirelessly connect to the internet using Window XP, yet I can on Mac OS X. I have no idea on how to fix this, and it's really messing with me. D:<
    D: Some of these problems may not be specifically "Application" related, but the top one mainly is. (in my views)
    ~Twilight

    Twilight:
    Is it possible that you installed Windows XPSP1 instead of the required SP2? If yes then that is cause of all of your issues listed in your post. You have no sound and you cannot connect wirelessly because you still have been unable to install the boot camp drivers when you inserted the leopard disk.
    Please double check to see which version of windows XP did you install. Remember, you need windows XPSP2 for all this to work.
    Now, in the event that you installed XPSP1 then you will need to get to the microsoft windows site on a different computer and burn the Service Pack 2 for windows XP on a CD. After that boot your apple mac to XP side and insert the Service Pack 2 disk and install the pack. After that, it will ask you to restart the computer which you must and then once fully booted into XP then insert the leopard CD again and see if takes and installs all the necessary drivers.
    Axel F.

  • Why does Preview crash after install?

    Pretty smooth install of Lion - excpet for the Preview issue.  Immediately after launching, it crashes.  I've seen some comments that suggest going to the Library and adding the Root User to theSharing and Permissions - but I can't find the Root User...
    Would appreciate any help since I rely on Preview for a lot of my work.
    Thank you.

    Pretty smooth install of Lion - excpet for the Preview issue.  Immediately after launching, it crashes.  I've seen some comments that suggest going to the Library and adding the Root User to theSharing and Permissions - but I can't find the Root User...
    Would appreciate any help since I rely on Preview for a lot of my work.
    Thank you.

  • Dell Laptop Internet issue after installing HP software for the C309a

    We have a wireless network and I have the software and drivers for the C309a successfully installed on my Gateway (Vista) laptop without issue.  After installing all the drivers and software on my wife's Dell Inspiron 1525 (Vista) for  the printer, the laptop struggles to connect to the internet through the wireless router.  Any web site that is a https takes several attempts to log onto, others will connect after a refressh.  The HP Cue is also crashing and closing.  I uninstalled the HP software and the connection was back to being normal with no difficulty connecting to the net.  I re-installed the HP software and the same thing is occurring (even the HP Cue crashing) where you can not get on her AOL mail or even Facebook unless making several attempts (and even then no gurantee it will let you on).  I uninstalled the HP software and all is well again with the internet connection.  I have not installed the latest version of the HP drivers and software as this is version 12 and I see that version 13 is avalable.  Was this an issue in the past and does version 13 fix this or do I have another issue?
    Thank you for the advice.....
    Mike

    Some of the HP software creates a lot of network traffic.  It can overwhelm some routers.  What kind of router and ISP do you use?
    Download 13 from here but do not subscribe to the Customer Participation Program (it creates a lot of traffic).
    Message Edited by PrintDoc on 11-13-2009 09:00 AM
    Say thanks by clicking "Kudos" "thumbs up" in the post that helped you.
    I am employed by HP

  • Issues after installing Hotfix Rollup 5 for SP3

    Hi,
    Last weekend we installed Hotfix Rollup Pack 5 for SP3 on our (single) Exchange 2010 Enterprise server.
    This was needed to fix the WebApp Light issue with IE11 and to fix the problem where users were unsable to delete mails sent from multifunctionals.
    These 2 issues were fixed by installing the hotfix rollup pack, but now our users have different problems...
    Some users (not all of them, haven't found a common denominator yet) report that they don't see new mails in their Outlook 2010 box, even though they got the envelope notifier.
    When they change folder and back to the Inbox the new mail is suddenly visible.
    Same sort of "delay" happens when users mark a message for follow-up or try to change a message from unread to read.
    Some users also report that they see delegated mailboxes (mailboxes from other users that they have full mailbox access to) twice in their Outlook 2010.
    Outlook 2010 is running in online mode (because it's running on terminal/citrix servers), so it's no issue with caching as far as I understand.
    I've already checked if there are any updates for Outlook available, but we've installed them all already.
    I though I'd found something:
    Noticed a lot of errors in the application log on the Exchange Server which pointed me to this:
    http://theintegrity.co.uk/2010/08/mapi-session-exceeded-the-maximum-of-500-objects-of-type-objtfolder/
    I've added the registry values now with a value of 1500, but unfortunately this didn't help.
    The errors in the eventlog are gone, but even after restarting the IS some users still have these problems.
    One user reported that it takes about 7 minutes for a read mail to actually switch to "read" when looking at his inbox.
    Did anyone else notice these problems? And maybe have a fix for them?
    I really don't want to roll back the update :(
    I even rebooted the Exchange Server after installing the rollup even though that wasn't even necessary
    Thanks in advance!
    Regards,
    Jeroen

    Correct - http://support.microsoft.com/kb/2925273 discusses this issue.
    If you do raise a support case to request this, please ensure that you review and understand the requirements for IU installation and removal.
    For example:   You *MUST* manually remove it prior to installing Exchange 2010 SP3 RU6.
    Cheers,
    Rhoderick
    Microsoft Senior Exchange PFE
    Blog:
    http://blogs.technet.com/rmilne 
    Twitter:   LinkedIn:
      Facebook:
      XING:
    Note: Posts are provided “AS IS” without warranty of any kind, either expressed or implied, including but not limited to the implied warranties of merchantability and/or fitness for a particular purpose.

  • CD Driver Issues after installing 11.1.4

    After installing Itunes 11.1.4, my HP computer, running Windows 7, could no longer find the CD drive.  Upon investigation, someone suggested I update my registry to remove some entries.  I did the following:
    Start, enter regedit in search bar,
    Open regedit
    Left hand menus click HKEY_LOCAL_MACHINE
    SYSTEM
    CURRENT CONTROL SET
    CONTROL
    CLASS
    Then need to find  {4D36E965-E325........... (are more figures but not needed)
    on right hand window see if there is an upper filter or lower filter.....right click and delete the values if either are there.
    RESTART...
    This worked, but now Itunes complains every time I open it, saying some registry settings are missing for my CD drivers.  I've used Itunes on this computer succssessfully for years, until this upgrade.  Apple, whatever you did, please undo it.  Horrible release...

    Solving the iTunes Installation Problems in Windows
    1. Apple has posted their solution here: iTunes 11.1.4 for Windows- Unable to install or open - MSVCR80 issue.
    2. If the Apple article does not fully resolve the problem for you, then try Troubleshooting issues with iTunes for Windows updates - MSVCR80.

Maybe you are looking for