Einstellungen von Airport Extreme übernehmen?

Kann man die Einstellungen einer Airport Extreme unkompliziert auf eine Time Capsule übernehmen?
Möchte meine Airport Extreme durch eine Time Capsule ersetzen und die Einstellungen übernehmen, da das Einrichten der Airport Extreme nicht gerade leicht war.

Ja. Kein Problem. 50 Mbps nicht übermäßig ist.

Similar Messages

  • Airport extreme verschwindet nach hinzufügen von Express

    Gestern neueste Extreme und Express gekauft und installiert. Zunächst Extreme und mit Express erweitert. Jedesmal wenn die Express hinzukommt, bringt die Extreme einen Fehler und das Netz (2,4 oder auch 5) sind nicht mehr erreichbar. 10.7.5, 6.2, 7.6.3 auf den Airports.
    Danke für die Hilfe

    German Apfel wrote:
    After that I looked in the System Profiler / Network / Airport (it is still listed) and there it shows only this:
    Softwareversionen:
    Menüerweiterung: 6.2 (620.24)
    configd Plug-in: 6.2 (620.15.1)
    System-Profiler: 6.0 (600.9)
    Netzwerkeinstellung: 6.2 (620.24)
    Airport-Dienstprogramm: 5.4.2 (542.23)
    IO80211-Familie: 3.1 (310.6)
    From the looks of this....you do not have the Airport Network adapter installed on your machine. If so, it would have another line just below the Software version that says:
    Interfaces:
    en1:
    Card Type: AirPort Extreme (0xXXXX, 0xXX)
    Firmware Version: Atheros 9280: 2.1.9.5
    Locale: FCC
    Country Code:
    Supported PHY Modes: 802.11 a/b/g/n
    Supported Channels: 1, 2, 3, 4, 5, 6, 7, 8, 9, 10, 11, 12, 13, 36, 40, 44, 48, 52, 56, 60, 64, 100, 104, 108, 112, 116, 120, 124, 128, 132, 136, 140, 149, 153, 157, 161, 165
    Wake On Wireless: Supported
    Status: Off
    You should contact the vendor and get it replaced or have the airport network adapter installed

  • Airport Extreme als Repeater oder zu Netzwerk hinzufügen

    Hallo,
    ich bin im besitz eines Würfels vom Anbieter 3 (DREI) und einer Airport Extreme.
    Ich würde gerne meine Airport Extreme als Repeater nutzen oder mit dem Netzwerk vom Würfel verbinden, nur keines von beiden funktioniert.
    Jedes mal wenn ich im Airport Dienstprogramm meine AE für "Netzwerk verbinden oder erweitern" konfigurieren will, sagt er mir ständig "Beim Konfigurieren der Airport Extreme ist ein Fehler aufgetreten" und dann findet er die AE nicht mehr. Dann muss ich jedes mal an der AE den Restart-Knopf drücken damit ich wieder von vorne anfangen kann.
    Ich kann leider auch im Internet nichts dazu finden, nur über Airport Express aber das bringt mich ja auch nicht weiter.
    Vl kann mir ja hier jemand helfen???
    ...mein Ziel: Würfel von 3 im Wohnzimmer > Airport Extreme als Repeater im Keller > Q-NAP NAS via LAN, Epson Drucker und Apple TV via WLAN mit Airport Extreme verbunden > alle angeschlossenen Geräte bei AE im Netzwerk und Internet für Fernzugriff freigeben
    nur bei mir scheitert es leider schon bei der Netzwerkverbindung
    Bitte um Hilfe!!

    Hab dafür eine Airport Express. Müsste daher auch mit einer aktuellen Airport Extreme gehen.
    Best Answer
    Yes, you can use the Airport Extreme as a repeater or a network Extender. When you're setting it up with the Airport utility software, simply put it into repeater mode. The Airport Extreme has a range of at least 250 meters, which is about 820 feet, which is pretty impressive!

  • Airport Extreme Telekom Zugangsdaten

    Hallo,
    ich habe eine Airport Extreme gekauft und möchte mit dieser über einen TELEKOM DLS Modem/Router ins Internet.
    Dazu müssen in der Konfiguration des Airport Extreme die Zugangsdaten zur Telekom hinterlegt werden.
    Diese werden von der Telekom wie folgt angegeben:
    Anschlusskennung:                                   111111111111
    Zugangsnummer (vorher T-Online Nummer:) 111111111111
    Mitbenutzer Nummer:                                 1111
    Persönliches Kennwort:                              11111111
    Wie und in welcher Reihenfolge müssen diese Daten im Airport-Dienstprogramm eingegeben werden?
    Hier stehen folgende Felder zur Verfügung:
    Account Name:
    Kennwort:
    Dienstname:
    Hat schon jemand dieses Problem besiegt?

    If you have set up the AirPort Extreme again and the amber light is flashing......AirPort Utility will tell you why.
    Open AirPort Utility
    Click on the AirPort Extreme icon
    Look for the setting for Status
    Click on the amber dot there
    What does the message say?

  • Wie kann ich mit der AirPort Extreme speichern ?

    Wie kann ich mit der AirPort Extreme speichern ?

    Hallo PitOMally,
    Aperture bietet wenig Möglichkeiten den Raw Daten IPTC zuzufügen, da das raw format kameraspezifisch ist. 
    Wenn Du das Metadatenmenue verwendest -
         Metadata -> Write IPTC Metadata to Master (im deutschen Menu heißt das vermutlich: Schreibe IPTC Metadata in den Masterfile o.ä.)
    dann erzeugt Aperture eine Kopie des Raw-Masterfiles als Tiff-file in der Library, die ziemlich viel Speicher frisst, aber die IPTC tags enthält.
    Ansonsten ist die einzige Möglichkeit, beim Export
         File -> Export -> Master
    wieder einen Sidecar file auszugeben, aber den hast Du ja schon.
    Unabhängig von Aperture kann man versuchen mit exiftool, Automator oder AppleScript diese tags zu setzen, wenn man mit diesen Werkzeugen vertraut ist.
    Hummel Hummel aus Hamburg
    Léonie

  • Airport extreme fritz repeater

    hat jemand erfahrung wie man einen fritz repeater N/G mit einer airport extreme koppelt?

    Da die Flughäfen mit den meisten, wenn nicht alle, Wireless-Repeater, die nicht von Apple sind nicht kompatibel sind, gibt es kaum eine Chance, dass die Fritz-Repeater, die Sie erwähnen, werden daran arbeiten, die Funkreichweite verlängern.

  • Dt. Telekom Entertain Speedport Router W921V + Airport Extreme WLAN

    Hallo,
    seit kurzem habe ich einen Glasfaser Anschluß der Telekom. Wir Telefonieren, Surfen und beziehen unser Fernsehen (Telekom Entertain) über diese Verbindung. Die Telekom hat den dafür geeigneten Router Speedport W921V bereitgestellt. Wir haben zusätzlich einen Airport Extreme (APX)  für die WLAN Versorgung installiert. Dieser ist nicht verzichtbar.
    Der APX meldet bei seiner Einrichtung einen Konflikt (Double-NAT) der dadurch zu beheben ist, dass der APX im Bridge Modus betrieben wird. Obwohl der APX dann über eine grüne Statuslampe verfügt, klappt die Anmeldung unserer 2 iPhones und eines iPods nicht bzw. die Verbindung lässt keinen Datentransfer zu. In der Airport App wird der APX ohne Statuslampe angezeigt. Die Statuslampe des Internet leuchtet orange.
    Wenn kein TV läuft kommt jedoch eine Verbindung inkl. Datentransfer zu Stande. Läuft ein Fernseher oder auch zwei, funktioniert das APX-WLAN nicht mehr.
    Die kabelgebundene Ethernet-Verbindung, die auch über den APX an den Speedport W921V läuft, funktioniert problemlos.
    Kann mir jemand einen Weg aufzeigen, wie der APX zu konfigurieren ist, damit die WLAN-Verbindung klappt?
    Falls nicht hieße das, dass der APX nicht mit Entertain-Standardhardware funktioniert.

    Hallo,
    ich hatte gerade fast das gleiche Problem mit der Kombi Fritzbox 7390 + neueste = 6. Generation Airport Extreme und einen daran über Ethernet angeschlossenen Telekom Entertain Receiver. Das WLAN der APX ist abgeschmiert, sobald ich das IP TV Entertain angemacht habe. Den Grund hast Du oben ja schon genannt.
    Jetzt scheint es gelöst durch die Firmware 7.1.x oder neuer, die wohl seit letztem Herbst IGMP Snooping erlaubt!
    Dadurch erhält nur der Entertain Receiver die IP - TV - Datenpakete von der APX und nicht wie zuvor noch alle Clients im Netzwerk. Dadurch bleibt das WLAN der APX stabil. Ich weiss jedoch nicht, ob das bei den älteren APX auch funzt.
    Einfach im Airport Dienstprogramm 6.3.x unter dem Reiter "Netzwerk" die "Netzwerkoptionen" öffnen und dort "IGMP Snooping" mit Häkchen aktivieren.
    Just for Info.
    Grüße

  • How do I use my airport extreme with my FIOS router?

    How do I use my AirPort Extreme base station with my FIOS Router to extend my network?  I have hard disks connected to my AirPort Extreme and would lik to access them.

    Probably can't answer all your questions - but.... I use a Linksys (wired and wireless) router as my primary entry point for FIOS. I use a Time Capsule and an Airport Express as a common wireless connection. So I have two visibile wireless networks and use them both depending on where I am in the house. Both the TC and AEx can be seen either wirelessly or wired from the entire network. Note - the Linksys provides all the DHCP - you set the apple routers as "bridge mode."

  • Help setting up Open DNS with new airport extreme

    I cant seem to get Open DNS to work with a new airport extreme. The status says I am not using Open DNS and its not filtering anything. I have followed the exact steps for set up listed on their website, checked the dns settings, cleared both caches and restarted the computer, modem and router with no success. I set the airport up in bridged mode, although I tried the other option under setup, but not sure what I was doing? I picked up this router because I wanted easy set up and the apple store assured me it would work with Open DNS. Oh, and I also downloaded the latest firmware update on the router. Can anyone help me with the settings or what else I need to check?

    Sorry, I am not familiar with this product, so I checked online to pick up some information.  Here I am referring to the information found here:
    http://www.dslreports.com/faq/6096
    I found that your device is mentioned as follows in the intro under Section 1 of this document:
    The BellSouth supplied Westell 2100, 2200 and 6100 models (Models A90-210030-04, B90-220030-04, and B90-610030-06/C90-610030-06, respectively) share many features and functions.
    Next, I am referring to the information under Section 2, under the heading of Standard Default Mode Connection (separate hub or switch present).  Unless you have changed the configuration on the Westell, this is how your device is operating. In this mode, the Westell device is acting both as a modem and router in one unit.
    So, an attached router (AirPort Extreme) must be configured as a switch to work correctly. That is what Bridge Mode is....the AirPort Extreme is operating as a switch when it is in Bridge Mode (which would be the correct setting to use when the Westell is set to its Standard Default Mode).
    Any changes that you want to make regarding DNS settings would need to be made on the Westell device, since it is acting as the main router on your network.
    In Bridge Mode, the AirPort Extreme simply passes that information through to its connected devices. You will not be able to make any DNS related changes on the AirPort Extreme since it receives that info from the Westel device. Some service providers force you to use their DNS servers, so you might want to check with Bell South or AT&T for more information in this regard.
    If you want to be able to configure the AirPort Extreme as the main router on your network, and instruct it to use the DNS information that you want, you will need to refer to the section under the heading of Bridged Ethernet Mode ( separate router present).
    Please note that the first item under this heading specifies that "This is the preferred configuration when using a separate external router..." (which would be the AirPort Extreme in your case)
    So, it appears to me that this would be the way that you must reconfigure the Westell device to allow the AirPort Extreme to function as the "main" router on your network. In this type of setup, you will be able to enter the DNS information that you want to use under the setup for the AirPort Extreme and it will act as you instruct.
    The AirPort Extreme would not be configured in Bridge Mode for this....it would be configured to "Share a public IP address".
    The next item in the article specifies that you "Must use a PPPoE client on the Router." This means that the AirPort Extreme would be configured to Connect Using = PPPoE as follows:
    AirPort Utility - Manual Setup
    Click the Internet icon
    Click the Internet Connection tab
    Connect Using = PPPoE
    You would enter your user name (probably your email address), password, etc in this area. Leave the Service Area box completely blank. Set Connection to Always On, and Disconnect if Idle to Never
    Click Update to save the new settings. Power off the Westell device after this and then restart it so that it will pick up the new information that you have programmed into the AirPort Extreme.
    I want to stress that this is how I would try to configure the Westell and AirPort Extreme. But, as I said, have not used a Westell device, so I cannot say that this will work correctly for you.
    It might be an excellent idea to contact Bell South or AT&T Support to ask for their opinion on this before you decide to change the configuration of the Westel device and the AirPort Extreme.
    This type of thing can be intimidating for users, so you might elect to use the services of someone like the Geek Squad at Best Buy, or a similar service from a local computer firm. Perhaps the Apple store could help as well.
    If it is not critical that you use Open DNS, you might want to simply leave things "as is", with the AirPort Extreme in Bridge Mode.

  • How do I open the same ports on an Airport Extreme Base Station for multiple computers at the same time?

    As the title suggests...
    I have a mix of five Mac and PC's at home using an Airport Extreme Base Station as the router.   I need many ports opened on the AEBS for all of the computers- not just one computer.  (for example: three people want to play TF2 on Steam at the same time; each machine needs the correct ports open on the router).   Port forwarding  only allows me to forward a given port to a single IP, yet I need that port open for five differnt IP's, all at the same time. 
    How do I do that on an AEBS?
    In the same way, I have a small office of four iMacs using an old airport with the same exact issue.   I would like to be able to connect to all of them remotely with Apple Remote Desktop, but the port forwarding on the airport only allows a port to forward to a single IP.   I want to be able to tunnel into the office network and log onto any machine behind the Airport extreme... not just a single IP.    I currently have it set up where I can tunnel into the office from my house, I can find the one machine that the port forwarding has been assigned to, I can log on and everything is just fine... with one machine.    How do I open the firewall for the other machines? 
    TL,DR version:  How do you open ports on an Airport Extreme Base Station instead of forwarding ports?   Forwarding ports doesn't work for multiple IP's.  

    You can open a single or multiple ports to a single device or different ports to different devices, but you cannot open the same port to multiple devices via the AirPort Utility for the Apple routers.

  • How do I add an airport extreme to a cable modem with only one ethernet port, while keeping that port connected to my Mac?

    I have a mac pro connected by ethernet to a cable modem via ethernet.    There is only one ethernet port on the modem.   
    I want to keep the Mac connected via ethernet for speed.    Is there a way that I can add an airport extreme to this set up - for my ipad and roku, and for guests to use - or do I need to buy a router to put between the modem and the mac?
    If I need a router, what kind?
    Thanks.

    The modem connects to the WAN "O" port on an AirPort Extreme router.
    The Mac Pro connects to one of the three LAN <-> ports on the AirPort Extreme router.
    Or if you do not need the ability to connect a hard drive to the USB port on the router, you can save a bit by using an AirPort Express.
    The modem connects to the WAN "O" port, the Mac Pro connects to the LAN <-> port
    Either the AirPort Extreme router or AirPort Express router will allow up to 50 wireless device to connect.
    There are many other wireless modems offered by other manufacturers as well.

  • Airport Extreme no longer recognizes or provides internet to wired devices

    Not sure if it was the power outage or an update that is the problem; but, I had a 5th generation Airport Extreme as the center of my home network with a solid connection to the internet for both my wired and wireless components.  A few days ago, after a power flicker (all components on surge protectors) my wireless internet would not stay connected more than 45 seconds before dropping and oddly, none of my wired components we showing up on the network or getting an internet signal from the AEBS.  After two hours with my ISP technical support personnel we deduced that the problem was the AEBS and the modem was fine.  I bought a new AEBS yesterday (the new long cube one) to use until my appointment to have the 5th gen looked at.  Plugged that in and instantly my wireless network came back up - rock solid.  However, anything I connect directly to the AEBS via ethernet does not get an internet connection or show up in the network.  I searched for two days in these forums for a similar problem - but, have gotten nowhere.  I used my wired connections for internet phone service and really need to get this fixed soonest.  Much thanks for any help anyone can throw my way.

    I would find it odd that you would have a replacement AirPort and still not have Ethernet connectivity ... but, of course, anything is possible. The DHCP service on the AirPort provides IP addresses to both wired and wireless clients by default so it shouldn't work for either if there was something amiss with it.
    At this point, I would suggest that you try the following:
    Perform a "factory default" reset on the AirPort. After it resets it will default to its "out-of-the-box" configuration which is a wireless Internet router that will broadcast an unsecured wireless network with a Network Name of something like: Apple Network NNNNNN.
    Without making any changes to the AirPort, try connecting any of your wired devices to it. If it still does not get the proper IP address and network connectivity I would suggest that you try performing a complete power recycle of your networking hardware. Please check out the following AirPort User Tip for details.

  • Time machine can no longer see USB drive connected to airport extreme

    According to what I read, as of March, a year ago March, with update 7.3.1 Time Machine will see the USB hard drive connected to the Airport Extreme. This was working fine. It no longer does. I had the latest airport extreme software and firmware updates. I tried going back to 7.3.1.
    Does any one have any idea how to make Time Machine work again when connected to my airport extreme?

    bradleydad wrote:
    According to what I read, as of March, a year ago March, with update 7.3.1 Time Machine will see the USB hard drive connected to the Airport Extreme. This was working fine. It no longer does. I had the latest airport extreme software and firmware updates. I tried going back to 7.3.1.
    Does any one have any idea how to make Time Machine work again when connected to my airport extreme?
    what exactly do you mean when you say that TM doesn't see the drive? do you mean you can not choose it as the destination TM drive in TM system preferences? do you see the airport drive mounted in finder? if yes, connect it directly to your mac and repair the disk (not permissions) with disk utility. then move it back to AEBS. see if that helps. if not try the following terminal command
    defaults write com.apple.systempreferences TMShowUnsupportedNetworkVolumes 1
    it should not be necessary with drives connected to AEBS but it might work.

  • USB HDD not ejected properly...no longer recognized by Airport Extreme

    I'm hoping someone can help.  I'm quite desperate as all of my DVDs are on this drive.
    I have a 2 TB WD USB harddrive that I connect to my airport extreme to use as my iTunes storage.  Up until 2 days ago there have never been any issues.  I was messing around, cleaning up around the router and hard drive and the USB cable was pulled out of the harddrive.  Now when I plug the USB cable back into the drive, it is not recognized in the Airport Utility.  I installed an older version of Airport Utility and it shows the volume, but I cannot do anything with it.  It is also not recognized in finder.  If I plug the drive directly into my MBP, it mounts fine and is totally accessible.  What could have meesed up with the drive?  I have another 1TB drive that I tried and this is recognizable in Airport Utility and finder along with a USB stick I have laying around.  It is only the drive that has all my stuff on that is no longer usable.
    If anyone has any suggestions I would be very greatful.
    For what it's worth, I've tried everything I can find on here and the web short of reformatting the entire drive.  I can't do this as I'll lose all my "stuff".
    Thanks in advance.
    Marc

    This is a user to user discussion area. So it is unpredictable as to when someone with a suggestion will respond to your post. An hour in the middle of a work day isn't a long time.
    Since the card is recognized, there isn't anything wrong with that side of the card. If the card isn't receiving a signal, either the RF side of the card has failed, the antenna wire isn't connected properly, or the antenna in the PowerBook has failed.

  • Airport Extreme Printing Problem with HP Deskjet.

    Hello ... I wonder if any helpful folks can assist me with my printing problem? I am using Tiger on a new Intel imac with a HP Deskjet 960C. This printer is listed as having the latest drivers included within Tiger and works perfectly when connected via USB so my problem I guess is not with the software....I have disconnected everything and plugged everything back together again. I also deleted the printer from the printer list within the Printer Setup Utility application.... The imac recognisies the printer and upon pressing the print button everything feels as though its just going to work. The blue barber shop scroll appears but the printer fails to kick into gear and I get the big red exclamation mark appearing in the status box .... I would really love to try and sort this annoying error ... Any ideas? Thanks. Book G4   Mac OS X (10.4.4)  

    Hello jds17. Welcome to the Apple Discussions!
    Unfortunately, not all USB printers are compatible with AirPort base stations.
    Take a look at one of these iFelix Unofficial AirPort Printer Compatibility links, depending on which AirPort base station you have:
    o 802.11g AirPort Extreme Base Station (AEBS) or AirPort Express Base Station (AX)
    o 802.11n AirPort Extreme Base Station (AEBSn)
    If your printer isn't listed, it doesn't necessarily mean it won't work, but simply that it has not been verified. iFelix also provides the following workaround for printers not on the list that would certainly be worth a try.
    Also, you may find the following Apple article helpful.

Maybe you are looking for

  • Clearing/Addressing GR/IR item that has been paid

    Hi All, I am soliciting input in trying to resolve an issue related to GR/IR clearing.  The GR/IR account was not regularly cleared using MR11 or F.13.  While trying to reduce the line items we have come across a few that have me puzzled. The followi

  • How do I install an earlier version of firefox than the download page recommends?

    I have a new PC and need to be able to use the delicious bookmark add-on for work. I loaded firefox 4 and the bookmark doesn't work so I need to load an earlier version and can't figure out how....only see an option to install firefox 4.

  • Setting the source-interface in a tcl script for email.

    So once again I am trying to figure this out and failing miserably. The only thin I can think of at the moment is that I need to tell it to source from a specific vrf interface. I've tried looking through possible enviornment variables. Hoping I coul

  • Issues distributing large content to pull DPs

    I am having issues trying to distribute big files to PULL DPs.  All other packages are going through fine.  But when I try to ditribute wim files over 4Gb, they never start downloading.  The pull site shows a bits.tmp stub file the size of the actual

  • Problems converting Robohelp 7 to Robohelp 9

    I recently upgraded to Robohelp 9, and tried to take my files with me. The first attempt ended with all of my Robohelp 7 files corrupted and unusable. I recovered from backup, and tried importing one by one. Each time, the system hangs and the files