Email in Inbox keeps dropping off.

EMail in Inbox keeps dropping off.

hi Robert,
thanks a lot for your reply.
here is the uplink port profile config:
port-profile type ethernet HostUplink
  vmware port-group
  switchport mode trunk
  switchport trunk native vlan 1
  switchport trunk allowed vlan 1-3967,4048-4093
  channel-group auto mode on mac-pinning
  no shutdown
  system vlan 803,832,900-901
  state enabled
803 is mgmt for both esx and vsm, 900 is control, 901 is packet.
my NC553i driver version is different from what you suggested, it is 2.102.518.0, any reason why you suggest to use the version you specified?
I have been trying to contact HP support, to be honest, not saying overall, but from my experience, they are much less helpful then Cisco support, I will keep trying.
thanks
ming

Similar Messages

  • Since I have downloaded IOS5 on my IPAD and synced to my IMac, Safari keeps dropping off before downloading the website, is slow, also an icon which accessed open safari windows is no longer available.  Apps trouble too.  Help?

    Since I have downloaded IOS5 on my IPAD2 and synced to my IMac, Safari keeps dropping off before site is downloaded and is slow.  There was an icon that showed how many windows were open on Safari and when pressed displayed them, that has disappeared and apps do not always download.  Sometimes by making several/many attempts, it eventually downloads the website or app, but this is not right.  When trying to dowload any lonks from an email, they simply do not open, it keeps going back to the home screen.  Does anybody have any suggestions?  I only bought the IPAD 2 in June! 

    Also the touch screen does not seem to be responding adequately.  Thank you for any help you can give.

  • 1131 LAP keeps dropping off

    Hi, folks.
    I have an 1131 LAP that keeps dropping off the network. I have plugged it directly in to the switch but it cycles the colours as if it can't find the controller.
    Any tips on where to start troubleshooting ?
    NM

    Here's some output from the access point, which appears to be constantly rebooting
    state to down
    *Mar  1 00:00:13.124: %LINEPROTO-5-UPDOWN: Line protocol on Interface FastEthernet0, changed state to up
    *Mar  1 00:00:24.230: %CDP_PD-4-POWER_OK: Full power - NEGOTIATED inline power source
    *Mar  1 00:00:24.298: %DOT11-6-FREQ_SCAN: Interface Dot11Radio0, Scanning frequencies for 29 seconds
    *Mar  1 00:00:30.308: %LWAPP-5-CHANGED: LWAPP changed state to DISCOVERY
    *Mar  1 00:00:30.326: %LINK-3-UPDOWN: Interface Dot11Radio0, changed state to up
    *Mar  1 00:00:30.335: %LINK-3-UPDOWN: Interface Dot11Radio1, changed state to up
    *Mar  1 00:00:30.343: %LINK-5-CHANGED: Interface Dot11Radio1, changed state to reset
    *Mar  1 00:00:30.430: %LINK-3-UPDOWN: Interface Dot11Radio1, changed state to up
    *Mar  1 00:00:30.437: %LINK-5-CHANGED: Interface Dot11Radio0, changed state to reset
    *Mar  1 00:00:30.544: %LINK-3-UPDOWN: Interface Dot11Radio0, changed state to up
    *Mar  1 00:00:31.430: %LINEPROTO-5-UPDOWN: Line protocol on Interface Dot11Radio1, changed state to up
    *Mar  1 00:00:31.544: %LINEPROTO-5-UPDOWN: Line protocol on Interface Dot11Radio0, changed state to up
    *Mar  1 00:00:41.786: %LWAPP-5-CHANGED: LWAPP changed state to JOIN
    *Mar  1 00:00:41.787: %LINK-5-CHANGED: Interface Dot11Radio0, changed state to administratively down
    *Mar  1 00:00:41.787: %LINK-5-CHANGED: Interface Dot11Radio1, changed state to administratively down
    *Mar  1 00:00:42.787: %LINEPROTO-5-UPDOWN: Line protocol on Interface Dot11Radio0, changed state to down
    *Mar  1 00:00:42.787: %LINEPROTO-5-UPDOWN: Line protocol on Interface Dot11Radio1, changed state to down
    flash:/env_vars.tmp: No space left on device
    *Mar  1 00:00:48.787: LWAPP_CLIENT_ERROR_DEBUG: spamHandleJoinTimer: Did not recieve the Join response
    *Mar  1 00:00:48.787: LWAPP_CLIENT_ERROR_DEBUG: No more AP manager IP addresses remain.
    *Mar  1 00:00:48.807: %SYS-5-RELOAD: Reload requested by LWAPP CLIENT. Reload Reason: DID NOT GET JOIN RESPONSE.
    *Mar  1 00:00:48.807: %LWAPP-5-CHANGED: LWAPP changed state to DOWN

  • Why does my generation 1 ipad keep dropping off

    Why does my ipad keep dropping off. It is generation 1.

    Dropping of of what - wifi? When you ask a question you need to provide enough info to get an answer.
    Some things to try first:
    1. Turn Off your iPad. Then turn Off (disconnect power cord for 30 seconds or longer) the wireless router & then back On. Now boot your iPad. Hopefully it will see the WiFi.
    2. Go to Settings>Wi-Fi and turn Off. Then while at Settings>Wi-Fi, turn back On and chose a Network.
    3. Change the channel on your wireless router (Auto or Channel 6 is best). Instructions at http://macintoshhowto.com/advanced/how-to-get-a-good-range-on-your-wireless-netw ork.html
    4. Go into your router security settings and change from WEP to WPA with AES.
    5.  Renew IP Address: (especially if you are droping internet connection)
        •    Launch Settings app
        •    Tap on Wi-Fi
        •    Tap on the blue arrow of the Wi-Fi network that you connect to from the list
        •    In the window that opens, tap on the Renew Lease button
    ~~~~~~~~~~~~~~~~~~~~~~~~~
    iOS 6 Wifi Problems/Fixes
    Fix For iOS 6 WiFi Problems?
    http://tabletcrunch.com/2012/09/27/fix-ios-6-wifi-problems/
    Did iOS 6 Screw Your Wi-Fi? Here’s How to Fix It
    http://gizmodo.com/5944761/does-ios-6-have-a-wi+fi-bug
    How To Fix Wi-Fi Connectivity Issue After Upgrading To iOS 6
    http://www.iphonehacks.com/2012/09/fix-wi-fi-connectivity-issue-after-upgrading- to-ios-6.html
    iOS 6 iPad 3 wi-fi "connection fix" for netgear router
    http://www.youtube.com/watch?v=XsWS4ha-dn0
    Apple's iOS 6 Wi-Fi problems
    http://www.zdnet.com/apples-ios-6-wi-fi-problems-linger-on-7000004799/
    ~~~~~~~~~~~~~~~~~~~~~~~
    Look at iOS Troubleshooting Wi-Fi networks and connections  http://support.apple.com/kb/TS1398
    iPad: Issues connecting to Wi-Fi networks  http://support.apple.com/kb/ts3304
    WiFi Connecting/Troubleshooting http://www.apple.com/support/ipad/wifi/
    How to Fix: My iPad Won't Connect to WiFi
    http://ipad.about.com/od/iPad_Troubleshooting/ss/How-To-Fix-My-Ipad-Wont-Connect -To-Wi-Fi.htm
    iOS: Connecting to the Internet http://support.apple.com/kb/HT1695
    iOS: Recommended settings for Wi-Fi routers and access points  http://support.apple.com/kb/HT4199
    How to Quickly Fix iPad 3 Wi-Fi Reception Problems
    http://osxdaily.com/2012/03/21/fix-new-ipad-3-wi-fi-reception-problems/
    iPad Wi-Fi Problems: Comprehensive List of Fixes
    http://appletoolbox.com/2010/04/ipad-wi-fi-problems-comprehensive-list-of-fixes/
    Fix iPad Wifi Connection and Signal Issues  http://www.youtube.com/watch?v=uwWtIG5jUxE
    Fix Slow WiFi Issue https://discussions.apple.com/thread/2398063?start=60&tstart=0
    How To Fix iPhone, iPad, iPod Touch Wi-Fi Connectivity Issue http://tinyurl.com/7nvxbmz
    Unable to Connect After iOS Update - saw this solution on another post.
    https://discussions.apple.com/thread/4010130
    Note - When troubleshooting wifi connection problems, don't hold your iPad by hand. There have been a few reports that holding the iPad by hand, seems to attenuate the wifi signal.
    ~~~~~~~~~~~~~~~
    If any of the above solutions work, please post back what solved your problem. It will help others with the same problem.
     Cheers, Tom

  • HT1338 wifi connection keeps dropping off on macbook pro

    hi, i just bought a Macbook Pro 13" and find that the wifi connection on my Macbook keeps dropping off every few minutes. i have tried numerous measures suggested that i could find on the net but the problem still persists. i don't know if it has anything to do with the Norton Internet Security that i installed on the laptop. pls help. thanks.

    Wi-Fi: How to troubleshoot Wi-Fi connectivity
    Wi-Fi Problems in OS X Yosemite
    Wireless Diagnostics
    Also try turning off Bluetooth.

  • Help! Broadband keeps dropping off

    I need some help.I rely on my infinity to work at home. Since beginning of the week the broadband has been constantly dropping off I suspect it may have happened prior to then as tablet would be offline in morning. Now it's dropping, at times, every 20 mins. Work are very annoyed. I have to connect the systems wireless( hence why chose "good" Infinity).I'm on hub5.  The internet only drops for few seconds but enough to kill everything in house. Once the hub went orange but usually blue. We have replaced the micro filter, reset hub with pin twice, changed channels, split the WiFi to 2.4 and 5Hz. Still dropping off
     They say nothing wrong with the line but with our previous supplier they said we had imbalance on copper wire. I'm now suspicious it was never fixed. Called bt today but got no answers to my questions. Right at end of one hour call was told that software is to blame but it's going to take a week to fix. What do I do about work? I can't connect wired and I'm going to lose my job. Obviously my questions were outside the script ...
    HOw can I be certain it's still software problem ? Is there any way I can connect to the main socket with my laptop wired to see if still dropping off rather than the hub? Can I use a different router? Is the hub less stable on an extension from master socket?
    Can the customer service people actually see if there has been a millisecond drop off? They said they can see I've only had two but it's more like 5 an hour. Even happened when on phone. I can be sat within metre of hub and it still drops off. How can I tell if someone is interfering with the WiFi connection in the house? What do I need to be asking them  to check regarding the copper resistance. One customer service representative said he'd reset the Cooper. Personally I can't see that happening as engineer previously picked it up by getting to the house only.
    Like I said I'm getting so worried as broadband is essential for my job.
    Thanks

    Apparently I said last post was solved but it's not. Can someone advise on my line info? Thanks 
    Product name:
    BT Home Hub
    2. Serial number:
    +068343+NQ41051489
    3. Firmware version:
    Software version4.7.5.1.83.8.204 (Type A) Last updated 23/01/15
    4. Board version:
    BT Hub 5A
    5. DSL uptime:
    0 days, 07:57:03
    6. Data rate:
    9999 / 39993
    7. Maximum data rate:
    24409 / 74218
    8. Noise margin:
    22.6 / 16.1
    9. Line attenuation:
    16.1 / 15.0
    10. Signal attenuation:
    15.8 / 15.1
    11. Data sent/received:
    72.7 MB / 3.7 GB
    12. Broadband username:
    [email protected]
    13. BT Wi-fi:
    Yes

  • Second External Drive Keeps Dropping Off

    I have two external G-Drives daisy chained together via firewire 800 and each have their own power plug.  They show up on finder as Drive A and Drive B.
    They normally spin down when not accessed and spin up as needed.  It appears that when I wake up the Mac from sleep mode, Drive B
    is dropped off and Drive A is still on finder.
    The only way to get drive B to show up again is to power it off then back on.  Is there anyway to correct this?

    Primary reason for electromagnetic devices to fail is the power surge at
    start up and the resultant warming up to a satisfactory operating
    temperature. Akin to light bulbs failing on startup, but not when
    constantly burning.
    Hmm, I've heard that one before, but I'm skeptical. And not sure the light bulg analogy is really suitable. Even shut down, if still connected to power, there's trickle current going to  the hardware, if I'm not mistaken. Anyway, there are posts from people who've shut down at night for ten years straight who've had no problems and then from users like you who swear by the opposite. A lot of this is just too anecdotal. I still need to see convincing statistics; and I don't think there are any.
    And even if you're right about the startup power surge and temperature jolt to the drive, you'd still have to weigh in the possible negative of too much heat, too much of a good thing by never allowing it to sleep. Must also depend on ambient room temp. It was just 103 here (90+ inside) and I don't think I would have been helping the hardware last by not allowing the computer to sleep under those conditions.
    Apple's recommendation to only shut down if the computer won't be used for a length of time and sleep otherwise is based more on the convenience  factor. There's nothing in there about what's better for hardware.
    Anyway, different strokes etc. Not something that will ever be settled definitively one way or the other. Probably a lot depends on the luck of the draw.
    Btw, Seagate's are getting a reputation lately for being pretty crappy.

  • Broadband connection keeps dropping off

    Hi everyone, anybody having a problem with there broadband connection dropping off constantly with the new BT infinity broadband. I constantly have to switch my IPad off when I am on line and my laptop and wireless printer is also being affected by this. Can anyone suggest how I can correct this problem? Thanks in advance for any help. j

    If all of the connections are wireless it is probably an issue with that rather than the Infinity connection itself. Download Inssider 2 onto your laptop and check if another network is using the same channel as yours. 

  • Galaxy Note Edge Wifi Connection keeps dropping off

    My wifi connections keeps disconnecting even after many attempts to login and getting connected on my home wifi it disconnects within a few seconds. Checked my modem and router and all is good (up to date firmware) and no connection issues on other devices. I verified my Edge is up to date as well. I am at a loss as to why it keeps auto disconnecting from my wifi. I tested tethering to my other cell phone and it stayed connected to it. So where do I go from here?

    Cesmenow,
    Thanks for reaching out to us. We can assist you. To confirm, this is only happening on your home wi-fi connection or do you also experience it with all wi-fi's?
    We can try a couple of troubleshooting steps to resolve this: First, try resetting the app preferences by going to Settings>General>Application manager>Applications then press Settings>Reset app preferences. Tell us if this helps.
    If not, then please run your device in Safe Mode - http://tinyurl.com/oo54noe and try again. This turns off all 3rd party apps. Tell us if it helps. 
    Thank you,
    Samsung Support ^Kov

  • HP 2320 network printer keeps dropping off network

    I have a small home network, running off a current gen TimeCapsule. I have an HP Colorlaser CM2320 network laser printer connected to a 5-port switch on the network. Randomly, the printer disappears. When selected in a print dialog, the satus is offline. But of course, it's not offline. It's connected and powered on, the switch is connected and powered on. I have powered cycled the printer, the switch, and the TimeCapsule. No success. Later, the printer magically becomes visible again. Later still, is goes away. This is driving me and my family crazy. The most recent problem started a few days ago. I printed several documents with no problem. My wife later in the day tried to print, but nothing. I spent several hours power cycling all the devices, plugging and unplugging ethernet cables, but no success. The next day, all of a sudden it starts printing my wife's document. A few hours pass, and I want to print, but the printer has again disappeared. It has not come back in two days now.
    Thanks to anyhone who can help. Rick

    Betcha it is Lion on the computer.. I have a network HP laser and it never goes offline with SL.. and TC running good old reliable 7.5.2 firmware.
    The printer name and IP must be recognised by the Mac.. did you lock the values on the printer or are you using dhcp?
    I recommend for printer lock the IP and name in the printer setup.
    If you still have issues see if you can ping the printer.. by IP and by Name.. if it fails please post the details of what actually fails.. For Lion and latest TC firmware Apple have some way to go to fix networking issues.

  • My ipad keeps dropping off the internet unless it is beside the router.

    I have tried in a friend's house but it does the same there, so it is an ipad problem not my router.
    Tried turning everything off etc but no good.

    Hello there, phillippa272.
    Good job with testing on another network. The following Knowledge Base article offers some standard troubleshooting steps as well as some additional information, that you should find helpful:
    iOS: Troubleshooting Wi-Fi networks and connections
    http://support.apple.com/kb/ts1398
    Thanks for reaching out to Apple Support Communities.
    Cheers,
    Pedro.

  • History keeps dropping off.

    Hello,
    I'm having a problem with the SQL Devleoper version 2.1.1.64 history. I think I set it correctly in teh preferences. Tools > Preferences > Environment > Local History correct? I set "Days to Keep History" to 45 and "Maximum Revisions per File" to 45 as well. However when I view the history I have a week at best, right now it's only 3 days. The older version used to hold all the queries I did for at least a month. Am I doing something wrong? How do I fix this?
    Thanks,
    Adam
    Edited by: el duderino on Mar 25, 2010 2:23 PM

    El Dude,
    That is for the history of editing local files. It allows you to diff a file against your changes to the file from 2 hours ago.
    The one your looking for is Database->Worksheet. SQL History Limit This limits how many things are in the sql history.
    -kris

  • HT4437 My airport express worked over the past year since it was purchased. Recently it keeps dropping off my iPhone 4, my brand new 5s and my iPad. It does NOT drop off my windows based laptop.  It does not lose wifi connection. Help?

    Can anyone help with this?  It is not wifi dropping the airport express. Wifi is connected. Music plays for 5 minutes or so and then goes silent.  It is as if the Apple iPhone and iPad is no longer recognizing the airport express. I need to open up the menu and. Lick on the airport express on iPhone and iPad to get it going again. Then it will drop over and over every 5 minutes or so. No problem with Apple TV. Also no problem with my windows laptop as all work s fine with no drops.  Crazy.

    What does any of this have to do with the Apple TV?

  • All my wireless Bluetooth devices (keyboard, mice) keep dropping off

    Do I need to replace a Bluetooth board or item in my 2009 MacPro? What should I order?

    BT in mac pro's leaves a lot to be desired.  Here's an ever growing thread on the topic:
    Poor Bluetooth reception and jerky mouse
    Bottom line, use a BT dongle or connect an external antenna to the BT board.  There are links to instructions there on how to do it. 

  • Why does my mac mini server keep dropping off the network?

    I have Verizon FiOS and use its router/wireless to connect all macbooks, macbook pros, etc. connect to each other and the snow leopard server, which runs the printers and time machine for one of the laptops.  I'm not using any other heavy duty server apps. I just want the mac mini to stay on the network and do its job.  Invariably when I go down stairs to the mac mini and ethernet to the router to share screen, I find some update that needs to be installed, which apparently is why the mac mini has gone on strike.  I usually can see the problem when I go to connect to server and see the other macbooks, but not the mac mini.  Then after much coaxing, I'm able to get the server back on line for a few days, until the next software update.  The server is set to auto restart, but why is it balking at rejoining the network?
    mac mini is running snow leopard, as are three of the four macbooks. router is an actiontec model.  wireless network is WPA2 and mac mini is ethernet connected to the router.

    I've just experienced this problem when using a Marantz SR4001 receiver between my Mac Mini and HD TV. I noticed that the problem didn't happen all the time and I have found a workaround solution.
    The problem is not a fault, but seems to be caused by the receiver defaulting the HDMI video properties. It's an old unit so I'm thinking that 720p is a default resolution for the receiver.
    I can make the problem happen if the receiver is turned on before the TV. Seems that without an output connection the receiver is telling the mac that it expects 720p.
    If I turn on the TV before the receiver, the TV seems to tell the receiver that it is expecting 1080p 25fps and the receiver obliges and the Mac retains those display properties.
    So it appears that the video output device dictates the output properties back to the receiver and the receiver in turn back to the Mac. In absence of an output device the receiver defaults to 720p.
    Solution: Turn on the TV before the receiver.

Maybe you are looking for

  • Problem while running Axis Service on JAxRPC Client

    hi, i have an axis service . I want to run it using JAXRPC client, but it was creating problem for simple primitive types like int,byte,short etc. on running it shows exception like deserialization error : java.lang.NumberFormatException: For input S

  • External monitor for 12" iBook G4 800MHz

    My iBook G4 800MHz has recently been promoted to being my main desktop computer. I am in the market for an external monitor that will work well with it. Does anyone who has direct experience with attaching external monitors to the iBook G4 have any a

  • J2me polish compilling in netbeans

    I'm trying to integrate netbeans with j2me polish but when rebuilding I get an error Buildfile: build.xml clean.tar.src: clean.resources: clean.devices: clean: build.tar.src:       [tar] Building tar: D:\projects\MobileClient1\CP_Phone_Backup-Src.tar

  • Suspected overheating issues

    Hey, everybody. I've had my PB for about 3 years now, and lately it's been freezing in the middle of graphics- or memory-intensive activities, like playing video games and watching movies stored on my hard drive. I've double-checked for viruses, corr

  • ISE 1.3 Guest API - using custom fields for guest creation?

    I am currently working with the new ISE 1.3 guest api, i have most everything working, i can create guests fine, with the basic information entered into the guest account like first name, last name, company, email, phone and so on. Now i need some mo