Envy dv7-7250 will not load Windows 7

I tried to install an OCZ Vector SSD and Windows 7 OEM , I can't get it to load Windows 7, I try to get the bios to load from the internal dvd drive and I get "selected boot image did not authetnicate" any suggestions??

Hi,
Please read the following informtion re. BIOS:
http://h10025.www1.hp.com/ewfrf/wc/document?cc=us&lc=en&docname=c00034791
Regards.
BH
**Click the KUDOS thumb up on the left to say 'Thanks'**
Make it easier for other people to find solutions by marking a Reply 'Accept as Solution' if it solves your problem.

Similar Messages

K7N2G will not load windows xp with any type of dvd/cd drive installed?

This is on my old computer, the specs are as follows
k7n2g
athlon 2600+
radeon 9700 pro
Caviar SE wd800
1gb samsung ddr333
It does not matter if it is keyed as master or slave, primary or secondary my old k7n2g will not load windows with a cd drive installed. I have tried three different drives and everything that I can think of, changed cables, channels, drives, everything. Windows just hangs. I cannot even get into safe mode. Is this an IRQ problem? The drives keeps trying to eject themselves, no matter what kind I use. This has never happened before, but there was a point before this problem where the vga wouldn't kick on (at the login screen) until I hit eject on the cd drive. This is driving me crazy and I have a girlfriend who just has to play her stupid sims and will not stop bothering me about it. PLEASE PLEASE PLEASE help me!
Thanks
Chris
PS here is my NEW workstation (I couldn't be happier to get rid of the old system)
two Opteron 250 90nm
2gb 2-3-2-6 Corsair Reg/ECC DDR 400
Tyan Thunder K8WE
1x BFG 7800GTX OC (one for now)
Audigy 4 Pro
Seagate Cheetah U160 10k 73.4 gb
Atlas V U160 18.3 gb
Lite on Dual Layer burner

Your Tyan based hardware listing on the first post has no relevance to anything, and might only serve to confuse. Please remove it and put the hardware you are trying to troubleshoot in a signature. Look in your profile>Forum Profile Information and enter that in the Signature box. That way we wont have to scroll to hunt down your hardware specs
So let us get this straight.
This system used to work fine? Yes? Then what prompted you to reload the OS?
You mentioned that didn't happen when you owned it. Are we to assume that at some point you sold or gave parts of this system to someone else? If so, what changed?
A little more history might prove useful in helping us to give you better suggestions.
Look at the PSU and give the Amps for the +3.3, +5v, & +12v lines.
***Edit, from what I see on the net, that is a dual rail PSU and the amps are as follows:
+3.3V@22A, +5V@21A, +12V1@18A, +12V2@16A
Is this correct?
Both the 3.3 and +5v seem a little low to me, but I am not entirely convinced that would be your problem. However, the fact that the 12v rails are split, can lead to other problems such as overvoltage protection circuitry getting in the way. Especially if the 16amp 12v rail is overloaded.
This is something to consider. Just because it is supposedly capable of wattage over it's rated power output doesn't mean it can handle what you're throwing at it all at once. If you have a single rail PSU that has at least 18 amps on the 12v rail to test with, we could almost definitively rule out power as the sole problem or a contributing factor.
I have never had a CD rejected, but if you could be more detailed about what you have connected to the board while attempting to load the OS, and then a detailed description of at what point the OS installation fails, and the CD is ejected, that would be helpful as well.
The fact that you've tried several drives, cables, with the same result. And also had a blackscreen event, does point to at least one problem that could point to a power issue. The CD rejection issue is foreign to me since I usually use the same type of PSU in all my builds or ones that I know work with a particular set of hardware, so I can't attribut that to a power issue.
Did you try clearing the CMOS and then initialize the default settings?
Do you have a cheap AGP card to try instead of the 9700?

Itunes will not load windows 8.1

I updated to Windows 8.1 and subsequently the itunews crashed when trying to open itune store and after multiple reloading and subsequently will not load at all, displaying a dialogue box saying itunes has stopped working and then closing the programme. Any thoughts?

I had moved my itunes app and the update had installed to the default directory

Will not load windows

trying to get comp. bootable or restored to factory
if i try to boot from hd in safe mode gets down to mup.sys and stops stays like there till i shut it down
i have the restore disks they will only load until setup says "setup is starting windows" then stops left it sit for hours it went no farther
this belongs to a friend no changes have been made that i know of
I've never seen anything like this before i took hd out and can access drive in my tower using usb adapter can see files
tried to boot it there in safe mode it get's to mup.sys and reboots machine over and over
tried load mini with no drive installed still does same thing
any help its like this thing is possessed
model: hp mini 1035nr
os: xp
thanks tom

you might have the rare instance of bad RCD's. You might wanna call HP tech support and explain to them that your disks will not load.
I work for HP.
Please click the White Kudos star on the left to say thanks.
Please mark Accept As Solution if this resolves your issue.

TPT2 will not load Windows 8, stuck on boot menu

Hello all,
It's my first post on this forum, and I'm having issues with a Thinkpad Tablet 2. I can power on the device but then it goes to the boot menu, which is empty. From here I don't know what else to do, as I cannot find any way to access Windows 8. I took it to a shop here in Toronto and they said that the boot menu being empty means that it isn't detecting any of the hardware that is connected to it and that it is most likely a hardware issue. They told me to go to Lenovo for assistance, but I wanted to check here first to see if you folks have got any advice for me. I've attached photographs of the empty boot menu anfd main screen of the Thinkpad setup, not sure if there is any relevant information in there. What should be my next step? Thanks in advance.

Hi there !!! I have exactly the same problem with my Thinkpad Tablet 2 (64MB). The only difference is that in my BIOS option UEFI safe boot is OFF. I tried to use recovery tool, Lenovo Diagnostic tool and even WindowsPE, but tablet simply cannot see any USB or any other devices. in startup/boot section is ONLY ONE POSITION: ! 1. Windows Boot Manager and I cannot boot from USB... I will be very grateful for any kind of suggestion (well, perhaps except suggestion to throw it out through a window). With kind regards Marco Polo

Will not load Windows XP on my Lenovo M58E but will load Windows 7 Help

I have a Lenovo M58E and i tried 3 diffrent XP Pro SP2 discs and it comes up with the Blue screen of death after it loads drivers off the cd and tries installing XP. If I put the windows 7 CD in it loads fine and will run. I need XP on this machine HELP

If you are running Windows 7 professional or Ultimate and want to run any legacy applications, I would suggest you try using Windows XP mode. More info here
http://windows.microsoft.com/en-us/windows7/install-and-use-windows-xp-mode-in-windows-7
Cheers and regards,
• » νιנαｿѕαяα∂нι ѕαмανє∂αм ™ « •
●๋•کáŕádhí'ک díáŕý ツ
I am a volunteer here. I don't work for Lenovo

Bootcamp will not load Windows installer - No bootable device, insert disk then press any key

Hello, I recently decided to install bootcamp onto my 2009 27" iMac, I have done this before for other people's computers and I thought it would be no different for my own. However, on attempt to install the Windows disk, instead of starting the installer it only gives me an error message saying No bootable device, insert boot disk then press any key. I have tried ejecting the disk and then putting it back into my disk driver but it still seems to give me the same error. I went back into my Mac using Alt(option) key on startup and then set the startup disk as the Windows installer disk but it doesn't seem to make a difference. I also tried booting the disk directly from the startup disk menu is the alt(option) key on startup but that didn't do anything different either.
Suggestions would be greatly appreciated!
Also if it helps my computer is a
2009 27" iMac running OSX 10.8.4
And my disk drive is an external drive because my internal SuperDrive went out.

That last point is your problem, Boot Camp doesn't really like booting from external drives.
You will have to do the following (assuming Boot Camp already partitioned your hard disk):
1. Use Disk Utility to make a CD/DVD Master of the Windows Install Disc.
2. Rename the resulting *.cdr file so it has an *.iso extension.
3. Insert a USB Flash Drive (8GB or more) into a USB port and start Boot Camp Assistant.
4. Make sure only "Create a Windows 7 or later version install disk" is checked.
5. Follow the directions, selecting the USB Flash Drive as the destination, and the *.iso as the source.
You should now be able to boot from and install Windows from the USB Flash Drive. It's annoying, but I had to do that.
You will need a second flash drive of 1GB or more, or 700MB or more extra space on the install disk to place the boot camp support files, which will need to be installed.

Envy DV7 laptop will not boot without the power cord being connected

My laptop won't boot on its own even when the battery indicator reads "fully charged (97%). If I have the power cord plugged into the computer (and the wall), it boots right away. Without the power cord, the "power indicator light" flashes once, the screen brightens to a lighter shade of gray, then it just shuts down.
I'm thinking I need to replace the battery but I thought it best to check with the experts first...................☺
Thanks!!
ETA..........I just saw the post about power cord failure. My power cord is one of those affected and I will be filling out the request for a replacement. Unfortunately my serial number is apparently located inside the battery compartment. I'm wondering if my cord has overheated and caused this boot problem with my computer.

Hello, @jksweeney
Welcome to the HP Forums.
I see that your having an issue with the power and your notebook. That you've applied to have the power cord replaced as it was part of the recall.
Please let me know when that has been taken care of if the issue remains. I will remain subscribe to this thread, so that I will be notified if you post again.
Thank you for posting on the HP Forums.
I worked on behalf of HP.

W540 will not load from SSD, need help

I just bought a W540 (windows 8) and extra SSD to replace the original HD in W540.
I have created a recovery image in windows 8 to my 16G USB flash and disabled intel rapid storage.
I put the new 512G Crucial MX100 SSD into the machine, and use USB flash drive to reset the laptop.
After the reset process was finished, I took out the USB flash drive, but the laptop will not load windows from my SSD, and the laptop did detect my SSD.
I am wondering if I did something wrong? I took out the SSD and put it in to my desktop, and I did see files were written into the SSD, but W540 will not load it,

The reason for your machine not booting might be found here:
Windows 8 Recovery Fails to Install on New Blank SSD
It does not give any info if the Recovery Media actually formats the drive in GPT mode, which is required for UEFI boot, in which case you might have to re-format your new SSD and re-install it with your recovery USB, which you're probably required to boot in UEFI mode as well. I have only installed Windows 8 in UEFI mode with an original retail DVD, and to achieve that I had to boot the DVD in UEFI mode.
HOW TO: Use the Diskpart.efi Utility to Create a GUID Partition Table Partition on a Raw Disk in Win...
ThinkPad W540 (20BG) - i7-4800MQ/24GB // ThinkPad T440s (20AQ) - i7-4600U/12GB
ThinkPad T440p (20AW) - i7-4800MQ/16GB // ThinkPad Helix (3698-6EU) - i5-3337U/4GB
ThinkPad W520 (4282-W4Q) - i7-2720QM/32GB // ThinkPad T400 (2767-W1C) - P9500/8GB
ThinkPad T61 (7665-CTO) - T7700/4GB // ThinkPad T60p (8741-C2G) - T7400/4GB

Windows 7 64 bit: Just installed firefox and pages will not load, or are very slow, IE explorer loads instantly

I installed windows ultimate 64 bit, Tried to install firefox for my default browser. Internet explorer loads everything like normal, no problem but firefox will not load or does after 5 mins +
I checked my firewall windows provides and Avira to see if they were blocking, Found nothing of anything being blocked.
This is a fresh installed windows 7, No viruses or malware

Start Firefox in <u>[[Safe Mode]]</u> to check if one of the extensions or if hardware acceleration is causing the problem (switch to the DEFAULT theme: Firefox (Tools) > Add-ons > Appearance/Themes).
*Don't make any changes on the Safe mode start window.
*https://support.mozilla.com/kb/Safe+Mode
A possible cause is security software (firewall) that blocks or restricts Firefox or the plugin-container process without informing you, possibly after detecting changes (update) to the Firefox program.
Remove all rules for Firefox from the permissions list in the firewall and let your firewall ask again for permission to get full unrestricted access to internet for Firefox and the plugin-container process and the updater process.
See:
*https://support.mozilla.com/kb/Server+not+found
*https://support.mozilla.com/kb/Firewalls

Itunes 10 will not load on windows 7 64 bit. Error code 2324. Old Itunes is gone or not working. Cannot play anything although files are still there. What the ??? is error 2324. Seems like alot of people ar ehaving the same problem

Itunes 10 will not load on windows 7 64 bit. Error code 2324. Old Itunes is gone or not working. Cannot play anything although files are still there. What the ??? is error 2324. Seems like alot of people ar ehaving the same problem

I have had this problem with Windows 7 and iTunes updates for some time. Each time it takes hours to solve but with the over the air upgrade to IOS6 on my iPhone and iPad, I was determined to solve and remember what I did, So here it is:
http://www.care4pcs.co.uk/2012/09/pear-shaped-apple-ios-6-for-iphone-ipad.html
I hope this helps you and any other users.

Hi- I applied the iTunes up to my Windows 7 86bit PC last Wednesday and iTunes will not load due to a Runtime error r6034Access to C Runtime Library Incorrectly. Then I get an windows error code 1114. I have tried rollling back and reinstalling but no joy

Hi- I applied the iTunes up to my Windows 7 86bit PC last Wednesday and iTunes will not load due to a Runtime error r6034Access to C Runtime Library Incorrectly. Then I get an windows error code 1114. I have tried rollling back and reinstalling but no joy

Hi Keen itunes User,
Thanks for using Apple Support Communities. This article has steps you can take for the error you're seeing:
iTunes 11.1.4 for Windows: Unable to install or open
http://support.apple.com/kb/TS5376
Cheers,
- Ari

IPhoto will not load the iPhoto library. When I select "show all windows" the library does appear but cannot open it. I am on version 8.1.2 and using Maverick.

iPhoto will not load the iPhoto library. When I select "show all windows" the library does appear but cannot open it. I am on version 8.1.2 and using Maverick.

I was able to get it fixed. I had received some responses and they had me
recreate the library I believe. It's been a while so I cant remember
exactly what I did. I have since upgraded to the latest i photo version and
have had no problems with it.
Brian
On Friday, November 7, 2014, Apple Support Communities Updates <

Thumbnails will not load in elements 12 organizer, using windows 8.1

The thumbnails will not load (hourglass icon appears on each photo) on Elements 12 using Windows 8.1. I have updated the Elements to Core Version 12.1. Any ideas how to fix this?

I'm sure that when I close the browser in either OS before switching to the other, the following two conditions are true in the Advanced tab of the Firefox Preferences menu:
1) "Use autoscrolling" is enabled (with a check mark)
2) "Always check to see if Firefox is the default browser on startup" is disabled (no check mark)
The autoscrolling feature allows you to scroll by holding down the middle mouse button and moving the mouse up and down. The extension you linked to, ScrollyFox, enables scrolling by clicking a button in the Firefox UI, which is quite a different feature. So unfortunately the problems still remain.

After updating to windows 8.1 PSE will not load

After updating to windows 8.1 PSE will not load. I have uninstalled and downloaded a PSE and installed several times with no success.

sorry it's not my apple id. it's my icloud email/account. after i updated to ios 8.1.2 my icloud acct on my phone is wrong. it's using my old college email address instead of my current icloud account email. my old college email address *used* to be my apple id, but i changed my apple id to my gmail account a few months back. anyway i can't "sign out" or delete the icloud account bc it thinks my college email address is my icloud account and it keeps asking for the password. so i'll type in the current password for my icloud account and it says it's wrong and i need to retry or change the password, which i've already done twice and nothing changes. probably bc its asking for the password associated with the college email address it thinks is my icloud acct.
i can access icloud on my desktop without a problem... make any sense? do i have to restore my phone now or is there a solution? i've wasted the last 2 days trying to figure this out. i can't send or receive emails on my iphone bc of this. which really ***** for work.

Envy dv7-7250 will not load Windows 7

Similar Messages

Maybe you are looking for