Error -1074395975 occurred at IMAQ AVI Read Frame DirectX has timed out readin

When i run the "Read AVI Example" on every kind of AVI file, I get the error:
Error -1074395975 occurred at IMAQ AVI Read Frame DirectX has timed out reading or writing the AVI file. When closing an AVI file, try adding an additional delay. When reading an AVI file, try reducing CPU and disk load.

The forums search gives two threads talking about this error:
http://forums.ni.com/ni/board/message?board.id=170&message.id=392042&requireLogin=False
http://forums.ni.com/ni/board/message?board.id=170&requireLogin=False&thread.id=195832
Did you allready had a look at them?

Similar Messages

Error en IMAQ AVI Read Frame

saludos al foro...
alguien me puede ayudar con el error-1074395975 ocurred at imaq avi read frame.
tengo labview 2011
ni vision 2011
ni vision assistant 2011
directx11
adjunto una imagen del diagrama a bloques y el mensaje de error
gracias
¡Resuelto!
Ir a solución.
Adjuntos:
imagen.png ‏39 KB

vicbit ....tal vez se podría revisar un ejemplo para la versión 2013 que podría servir ...... llamado "Read AVI File.VI" que se encuentra en la ayuda..... como menciona Omar las funciones relacionadas con el manejos de archivos AVI, fueron cambiados en la ultimas versiones asi que saldrá un poco diferente o tal vez el ejemplo no se encuentre . Yo pienso que el truco radica en el uso adecuado de los " Frames per Second" ,"Number de frames" y el "time Delay".
Algo que observe en los códigos que han subido anteriormente es que no es necesario usar dentro del ciclo la funcion "Imaq Create" ya que va a crear un espacio en memoria cada vez que se ejecuta un ciclo (Cada frame) esto no es necesario y podria afectar , además no se estan liberando estos espacios con "Imaq Dispose VI".
A continuacion la imagen del ejemplo que se encuentra en la versión 2013
en la versión 2010 se puede encontrar ejemplos también-->https://decibel.ni.com/content/docs/DOC-14904
Jonathan Cruz
CHALLENGER
K U D O S __ B I E N V E N I D O S

IMAQ AVI Read Frame Trigger Error

I have an application that is creating avi clips of a process. This application is writing frame data which is read later in another application. It is at this point, during the reading of the data that an Error -1074396037 Trigger error is occuring. I am using IMAQ Vision 7.0 and Labview 7.0. Attached is an avi that was created. It consists of a total of 75 frames. Also attached is a simplified version of the frame read part of my application. When reading the frame data I get the error at frames 36 and 51.
I was hoping somebody could have a look and see why I am getting the error.
Terry Sopkow
Sr. Reseach Technologist
Oilphase-DBR
Attachments:
ReadFrame.zip ‏596 KB

Hi Terry,
I ran your program with your video and got error 1074395975 DirectX has timed out reading the avi file. I do not think there is anything wrong with your program because I ran your program with a different avi file and it worked perfectly. I also ran the shipping example Read AVI Example.vi with your video and got the same timeout error.
So there must be something wrong with your avi file. Perhaps frames 36 and 51 are missing or corrupt for some reason. Try creating the avi file again and see if you still have the same problem. If you do, then we'll have to investigate the problem with the creation of the file.
Christopher W.
Application Engineer
National Instruments

IMAQ AVI read frame error

Hello,
What does the IMAQ AVI read frame error "Trigger Time out" mean ?
Thank you.

Hello Vanessa,
In some applications, when a trigger occurs after several minutes or when integration takes several seconds, the timeout parameter may be too small to wait the amount of time it takes to acquire an image. If the image you request is not ready by the timeout parameter, the acquisition code generates a timeout error.
To prevent this problem, check the acquisition status and request an image only when you know one is ready. By just checking the acquisition status and not requesting an image, you could wait indefinitely for an image without receiving an error.
Sanaa TAZI
Application Engineer
National Instruments

IMAQ AVI Read Frame vs. IMAQ AVI2 Read Frame, no data terminal

Hi,
I just noticed when dropping a IMAQ AVI2 Read Frame vi in place of an older IMAQ AVI Read Frame vi, there is no "data out" terminal. I do make use of this feature to add data to the frames of the AVI. Is there supposed to be an alternative way to store this frame data, using the imaq image custom info perhaps?

Hello David,
You are correct in that the data out terminal is no longer available in the AVI2 functions. However you can use the IMAQ Read Custom Data and IMAQ Write Custom Data functions. These allow you to write and read custom data to the IMAQ images using specified keys. In this way you can add miscellaneous data to your images for later use.
Earl C
Applications Engineer
National Instruments

Tried purchasing iTunes music. Put in my apple id and password then i was directed to a 'Terms and Conditions' page. I checked the box then clicked the 'accept' button next page read 'your Session has timed out ' try again with a Done button to click on

Tried purchasing music from the iTunes Store. When the window popped up I put in my apple id and password. Then I was directed to a 'Terms and Conditions' page. I checked the box next to the 'Yes I agree to these terms and conditions' - then clicked the 'accept' button next page read 'Your Session has timed out. Try again.' with a 'Done' button to click on. Oh the same thing happens when i try to download free iTunes. Yes I have tried & tried it again I even logged off and singed back in-- no joy
After accessing my iTunes account I was not able to change anything like my credit card number when I tried and was sent right to the 'Your session has timed out. Try again.'
The last time I purchased any anything was on September 25th 2011 and the 'terms & conditions' page was last updated on October 12, 2011
Does anyone have an idea to what is going on with my iTunes version 9.2.1 (5) and I can not upgrade to a higher version my iMac does not have the intel processor chip.Thank you for your time and help with this matter. You are greatly appreciated

I am having the same problem also! I posted on here about it, but no one has responded with ideas. I called technical support and e-mailed them, the only suggestions they gave was for the to turn off my firewall. But I didn't change anything, so it shouldn't suddenly stop working. Maybe this is just an iTunes issue? But it doesn't even recognize my account anymore, and I cannot log in now.
If you happen to get an answer, will you please let me know what works for you?
Thanks!

How do I fix this error: The iPad cannot be synced. The device has timed out?

Hello out there! Would someone be so kind as to point me in the right direction in fixing my little promblem? I can't seem to figure out how to get my syncing process to work properly. I've updated all my apps and I have even done the steps to configure. I've chosen to use "my iPad" back up feature and then the next step is to connect to iTunes and sync everything. It will do so and then it will say in the window box of iTunes "Finishing Sync". A minute or so later it will feature an error box presenting the statement: "The iPad, "my iPad" cannont sync. The device has timed out." Where do I go from here? Thanks to any with some good solutions. LJ

Oops! Shall I add that I have recently updated my iPad's iOS software to iOS 5.1.1 and this is when my troubles began. :-)

IMAQ AVI read frame performance

I've been playing around with the read AVI with buffer example in the Developer Community. It reads all the frames of an AVI into memory and then plays them back at the appropriate frame rate. This works ok with very small AVI files but with anything larger it gets slower and slower until it almost stops loading the AVI. At that point it seems to be loading less than 5 frames per second and is killing my cpu. I have plenty of free RAM during this.
https://decibel.ni.com/content/docs/DOC-8479
This is the case with the play AVI example that comes with Labview too (without a buffer) which just loads and plays one frame at a time. Can someone suggest a way to improve the performance of an AVI player in Labview? My ultimate goal is to read an AVI and detect changes in motion of objects by comparing two frames at a time. These AVIs are going to be at least 5 minutes in duration at a frame rate of 30 fps.
I'm using Labview 2009 with the Vision Developer installed.
Attachments:
image_png.png ‏77 KB

VTKim wrote:
Hi,
One thing we could implement is a compression filter that is on the IMAQ AVI Create VI used in conjunction with the IMAQ AVI Get Filter Names VI. Also, what is the RAM available on your computer and what size images are you acquiring and saving to AVI? Thanks!
Kim
Thanks for replying. I'm running labview 2009 on a dual core pentium 2.3 GHz with 4 Gigs of ram. It typically has 2 Gigs free while running the program.
I'm not tryingt write an AVI, I'm trying to read an AVI. The frames are 352 x 240 in size. I've tried several read AVI examples and they all act the same way. They slow down quickly and the hard drive and CPU are really cranking away.

Imaq erreur avi read frame

Voici l'erreur que j'ai sur mon VI si vous pouvez me renseigner se seraiat cool merci.
L'erreur -1074396010 s'est produite à : IMAQ AVI Read Frame
Solved!
Go to Solution.

Bonjour,
Cette erreur a été corrigé dans la version 2012 SP1 (12.1) du logiciel.
Je suppose que vous avez une version antérieure ?
Cordialement,
Maxime G. | Application Engineer
National Instruments France
#adMrkt{text-align: center;font-size:11px; font-weight: bold;} #adMrkt a {text-decoration: none;} #adMrkt a:hover{font-size: 9px;} #adMrkt a span{display: none;} #adMrkt a:hover span{display: block;}
LabVIEW Tour
Journées Techniques dans 10 villes en France, du 4 au 20 novembre 2014

ORABPEL-05002 - Message handle error - Session has timed out or was invalid

In our production environment we are facing this issue.
We are trying to find the root cause to fix the issue.
My Understanding:*
In the below error message,
we are able to see the Session has timed out or invalidated.
Also we are able to see the Non-fatal connection error. I believe that when the MDB trying to process the dispatched message, it will invoke the message from invoke_message table of dehydration store. At this point of time it gets non-fatal connection error so we are gettign this error.
I need to know the difference between fatal and non-fatal connection error. Is my understanding correct or not ?
ORABPEL-05002
Message handle error.
An exception occurred while attempting to process the message *"com.collaxa.cube.engine.dispatch.message.system.RemoveMessage"; the exception is: Session has timed out or was invalidated*
at com.collaxa.cube.engine.dispatch.DispatchHelper.handleMessage(DispatchHelper.java:207)
at com.collaxa.cube.engine.dispatch.BaseScheduledWorker.process(BaseScheduledWorker.java:70)
at com.collaxa.cube.engine.ejb.impl.WorkerBean.onMessage(WorkerBean.java:86)
at sun.reflect.GeneratedMethodAccessor36.invoke(Unknown Source)
at sun.reflect.DelegatingMethodAccessorImpl.invoke(DelegatingMethodAccessorImpl.java:25)
at java.lang.reflect.Method.invoke(Method.java:597)
at com.evermind.server.ejb.interceptor.joinpoint.EJBJoinPointImpl.invoke(EJBJoinPointImpl.java:35)
at com.evermind.server.ejb.interceptor.InvocationContextImpl.proceed(InvocationContextImpl.java:119)
at com.evermind.server.ejb.interceptor.system.DMSInterceptor.invoke(DMSInterceptor.java:52)
at com.evermind.server.ejb.interceptor.InvocationContextImpl.proceed(InvocationContextImpl.java:119)
at com.evermind.server.ejb.interceptor.system.SetContextActionInterceptor.invoke(SetContextActionInterceptor.java:44)
at com.evermind.server.ejb.interceptor.InvocationContextImpl.proceed(InvocationContextImpl.java:119)
at com.evermind.server.ejb.InvocationContextPool.invoke(InvocationContextPool.java:55)
at oracle.j2ee.connector.messageinflow.MessageEndpointImpl.OC4J_invokeMethod(MessageEndpointImpl.java:297)
at WorkerBean_EndPointProxy_4bin6i8.onMessage(Unknown Source)
at oracle.j2ee.ra.jms.generic.WorkConsumer.run(WorkConsumer.java:266)
at oracle.j2ee.connector.work.WorkWrapper.runTargetWork(WorkWrapper.java:242)
at oracle.j2ee.connector.work.WorkWrapper.doWork(WorkWrapper.java:215)
at oracle.j2ee.connector.work.WorkWrapper.run(WorkWrapper.java:190)
at EDU.oswego.cs.dl.util.concurrent.PooledExecutor$Worker.run(PooledExecutor.java:814)
at java.lang.Thread.run(Thread.java:619)
<2010-08-11 23:05:10,131> <ERROR> <WorkExecutorWorkerThread-129> <engine.dispatch> <DispatchHelper::handleMessage> failed to handle message
java.rmi.NoSuchObjectException: Session has timed out or was invalidated
at com.evermind.server.ejb.StatefulSessionEJBObject.throwPassivisationException(StatefulSessionEJBObject.java:335)
at com.evermind.server.ejb.StatefulSessionEJBObject.remove_X(StatefulSessionEJBObject.java:174)
at com.evermind.server.ejb.StatefulSessionEJBObject.remove_X(StatefulSessionEJBObject.java:159)
at com.evermind.server.ejb.LocalStatefulSessionEJBObject.remove(LocalStatefulSessionEJBObject.java:25)
at com.collaxa.cube.engine.util.EngineBeanCache.releaseMessageBean(EngineBeanCache.java:293)
at com.collaxa.cube.engine.dispatch.message.system.RemoveMessageHandler.handle(RemoveMessageHandler.java:36)
at com.collaxa.cube.engine.dispatch.DispatchHelper.handleMessage(DispatchHelper.java:142)
at com.collaxa.cube.engine.dispatch.BaseScheduledWorker.process(BaseScheduledWorker.java:70)
at com.collaxa.cube.engine.ejb.impl.WorkerBean.onMessage(WorkerBean.java:86)
at sun.reflect.GeneratedMethodAccessor36.invoke(Unknown Source)
at sun.reflect.DelegatingMethodAccessorImpl.invoke(DelegatingMethodAccessorImpl.java:25)
at java.lang.reflect.Method.invoke(Method.java:597)
at com.evermind.server.ejb.interceptor.joinpoint.EJBJoinPointImpl.invoke(EJBJoinPointImpl.java:35)
at com.evermind.server.ejb.interceptor.InvocationContextImpl.proceed(InvocationContextImpl.java:119)
at com.evermind.server.ejb.interceptor.system.DMSInterceptor.invoke(DMSInterceptor.java:52)
at com.evermind.server.ejb.interceptor.InvocationContextImpl.proceed(InvocationContextImpl.java:119)
at com.evermind.server.ejb.interceptor.system.SetContextActionInterceptor.invoke(SetContextActionInterceptor.java:44)
at com.evermind.server.ejb.interceptor.InvocationContextImpl.proceed(InvocationContextImpl.java:119)
at com.evermind.server.ejb.InvocationContextPool.invoke(InvocationContextPool.java:55)
at oracle.j2ee.connector.messageinflow.MessageEndpointImpl.OC4J_invokeMethod(MessageEndpointImpl.java:297)
at WorkerBean_EndPointProxy_4bin6i8.onMessage(Unknown Source)
at oracle.j2ee.ra.jms.generic.WorkConsumer.run(WorkConsumer.java:266)
at oracle.j2ee.connector.work.WorkWrapper.runTargetWork(WorkWrapper.java:242)
at oracle.j2ee.connector.work.WorkWrapper.doWork(WorkWrapper.java:215)
at oracle.j2ee.connector.work.WorkWrapper.run(WorkWrapper.java:190)
at EDU.oswego.cs.dl.util.concurrent.PooledExecutor$Worker.run(PooledExecutor.java:814)
at java.lang.Thread.run(Thread.java:619)
<2010-08-11 23:05:10,132> <ERROR> <WorkExecutorWorkerThread-129> <engine.dispatch> *<DispatchHelper::handleMessage> Not fatal connection error ... not retrying: class com.oracle.bpel.client.ServerException: Session has timed out or was invalidated*
<2010-08-11 23:05:10,132> <ERROR> <WorkExecutorWorkerThread-129> <engine.dispatch> *<BaseScheduledWorker::process> Failed to handle dispatch message ... exception ORABPEL-05002*
Message handle error.
An exception occurred while attempting to process the message "com.collaxa.cube.engine.dispatch.message.system.RemoveMessage"; the exception is: Session has timed out or was invalidated
-----

I'm having the same problem. I posted to VSM sample and Pooled ApplicationModule Maximum Inactive Age
which seems to be a similar situation.
Does anyone have any information on where this time out parameter is set on either the app module or OAS and how to handle this error correctly?
Thanks,
Brian

Error - 1074397153 occurred at IMAQ Grab Setup.vi

The sensor we are using is Goodrich SU640KTSX. I can run SUI image Analysis 3.1 software, Measurement & Automation software, and MATLAB code on an XP machine with no errors when grabbing images. We are tying to build a newer PC;
Dell T7500 with Intel xeon CPU x5650 @ 2.67GHz
Memory; 12GB
OS Win7 64-bit
Camlink card is NI PCIe-1430
Nvidia QUADRO 4000
The error we get is "Error -1074397153 occurred at IMAQ Grab Setup.vi / Cannot detect recognizable video source" when using the SUI image Analysis 3.1 software or MATLAB code. When we use the NI-IMAQ i/o 2.3.1- Measurement & Automation I can snap, grab and record without any error.
Any help on this would be great
Thanks

Hi,
Let us know which standard your camera is following (whether it is cameralink or ethernet).
Check this link for error info: http://digital.ni.com/public.nsf/allkb/3434173630CBC97686256F8000536593.
If at all it is cameralink camera make sure that you are following proper trigger sequence for your camera. As u are grabbing frames in MAX and not in other acquisition softwares it might be triggering issue or cables problem.

Error -1074397038 occurred at IMAQ Start.vi for 64bit Labview 2011 SP1, Win7

Hello,
I am using a MC1362 camera from Mikrotron with a PCIe1433 framegrabber. I was using it with windows XP, 32 bit, labview 2010 SP1 32 bit, it was working perfectly fine. I just switch to windows 7 with labview 2011 SP1 64bit, and it is not working anymore with my custom routine in labview, though it works with MAX and camera file generator and I use the same camera file.
When I run my routine, I have this error message:
Error -1074397038 occurred at IMAQ Start.vi
Possible reason(s):
NI-IMAQ: The requested serial termination string was not found in the returned buffer.
Then, If I try to run the camera with MAX, it doesn't work anymore, I have to reboot the camera, and put it in the right mode with the Mikrotron control tool to obtain an image.
I have seen similar issue on a Basler camera on the forum, and it has been solved by using a camera file to set the different parameters. There is no camera file complete to set all the parameters of the camera, so I had to program them in serial to drive the camera with my Labview routine.
Could you help me to solve this issue please?
Thanks
Bests
David Dulin

This forum post is already handled --> SR 1154262.
Kind regards,
Corné Westeneng
Applications Engineer
NI-Netherlands

Hi, I am getting an 'Error 4810 occurred at Sound File Read Open.vi' for the attached wav file (plus many other wav files). Any ideas?

Hi,
I am getting an 'Error 4810 occurred at Sound File Read Open.vi' for the attached wav file (plus many other wav files).
Any ideas?

No attachment exists.
Rolf Kalbermatter
CIT Engineering Netherlands
a division of Test & Measurement Solutions

Error -1074395395 occurred at IMAQ Match Color Pattern after merge programs

Dear all
I have 2 separate programs that use same source image (red01a1.jpg). The first find location of color particles (color location 01.vi) and second find location of particles after threshold color image (particle location 01.vi). Both of them run good.
But when 2 programs were merged into one program (color sorter 01i.vi), that happened error . The error message is “Error -1074395395 occurred at IMAQ Match Color Pattern”. How can I fix it ?
Thanks
Solved!
Go to Solution.
Attachments:
color sorter 01i.vi ‏126 KB
Color -particle location.zip ‏86 KB
red01a1.zip ‏86 KB

Hi Xuan
Check it out the attached vi
Sasi.
Certified LabVIEW Associate Developer
If you can DREAM it, You can DO it - Walt Disney
Attachments:
color sorter 01i.vi ‏120 KB

Error -1074397150 occurred at IMAQ Snap.vi

Hi.
(Sorry if my English is wrong )
I want to snap a picture - from a camera that was designed in my lab - and save it in a BMP file.
I use the "IMAQ PCI-1428" to accomplish this task and the "HL snap&save to BMP.vi".
But, as I try to run the VI I'm getting this error - "Error -1074397150 occurred at IMAQ Snap.vi", afterward I'm getting
another massage - "ERROR(DMA Timeout): The system is unable to capture all of the incoming video data....".
What should I do, to resolve this problem?
ThanX.

Hi elbit,
Here is a link to Error
Codes with NI-IMAQ. You error is
addressed there and that information may be helpful to you.
I noticed you were using the PCI-1428 framegrabber card. This card supports Camera Link cameras. In order to tell the PCI-1428 how to
communicate with the camera, the NI-IMAQ driver uses a camera file that
contains camera specific information for configuration. You will need to have a properly configured
camera file for you camera that you have created.
NI has a large number of camera files that are created and
certified to support popular industrial grade cameras. In cases where a custom camera file is needed,
NI provides the NI-Camera
File Generator as a utility for camera file creation. Keep in mind that custom camera files are not
supported by National Instruments Applications Engineers.
Good luck with your camera design. Please let us know if you have any further
questions or concerns.
Regards,
Luke H

Error -1074395975 occurred at IMAQ AVI Read Frame DirectX has timed out readin

Similar Messages

Maybe you are looking for