Error 4261 - really need some help from one of you pros!

I keep getting error 4261 when I try to burn CDs. I was able to do it for awhile just fine and suddently I can't anymore. Each time I try now I get partway through burning and it stops, the disk is ejected, and I get error 4261.
Here's what I have tried so far with no luck:
1. Decreased burn speed to 2x, on both iTunes and my CD burner
2. Turned off my virus scanning software (Live One)
3. Tried various makes of disks
4. Tried burning a new mix with just songs that I had ripped from my own CDs (i.e., no "protected" iTunes)
5. Updated to latest version of iTunes (7.3)
6. Tried going back to version 7.2
7. Ran diagnostics:
Microsoft Windows XP Professional Service Pack 2 (Build 2600)
Dell Inc. Dell DM051
iTunes 7.2.0.34
CD Driver 2.0.6.1
CD Driver DLL 2.0.6.2
LowerFilters: PxHelp20 (2.0.0.0), DRVMCDB (1.0.0.1), DLACDBHM (1.0.0.1),
UpperFilters: GEARAspiWDM (2.0.6.1),
Current user is an administrator.
Video Display Information:
RADEON X300 SE 128MB HyperMemory
RADEON X300 SE 128MB HyperMemory Secondary
Connected Device Information:
DiskDrive, WDC WD2500JS-75NCB1, Bus Type ATA, Bus Address [0,0]
CDROM, HL-DT-ST DVD+-RW GWA4164B, Bus Type ATA, Bus Address [0,0]
If you have multiple drives on the same IDE or SCSI bus, these drives may interfere with each other.
Some computers need an update to the ATA or IDE bus driver, or Intel chipset. If iTunes has problems recognizing CDs or hanging or crashing while importing or burning CDs, check the support site for the manufacturer of your computer or motherboard.
D: HL-DT-ST DVD+-RW GWA4164B, Rev D108
Audio CD in drive.
Found 13 songs on CD, playing time 56:25 on Audio CD.
Track 1, start time 00:02:00
Track 2, start time 04:20:25
Track 3, start time 09:03:00
Track 4, start time 12:43:17
Track 5, start time 16:09:07
Track 6, start time 20:03:02
Track 7, start time 24:53:57
Track 8, start time 29:09:72
Track 9, start time 33:22:52
Track 10, start time 38:01:52
Track 11, start time 42:28:17
Track 12, start time 47:01:25
Track 13, start time 52:02:35
Audio CD reading succeeded.
Get drive speed succeeded.
The drive CDR speeds are: 8 10 16 40 48.
The drive CDRW speeds are: 8.
The drive DVDR speeds are: 8.
The drive DVDRW speeds are: 8.
Force Optical Power Calibration before burn is turned on in the preferences.
The last failed audio CD burn had error code 4261(0x000010a5). It happened on drive D: HL-DT-ST DVD+-RW GWA4164B on CDR media at speed 16X.
Any suggestions???

There are a few points of interest on your Drivers and downloads page at Dell.
Dimension 5150/E510 (XP)
Check to see if the firmware on your HLDS GWA-4164B HH 16X DVD+/-RW is up to date. (That's the drive itunes is identifying as an HL-DT-ST.) at least one of the Dell firmware revisions to that was urgent and related to reading and writing to media.
Also,
Check to see if the Chipset drivers for your Intel Chipset are up to date.
Check to see if your Dell Dimension System BIOS is up to date.
Check to see if the video adapter driver for your ATI Hyper Memory PCI-Express X16 (DVI/VGA/TV out) Radeon X300 SE is up to date.
Once you're satisfied you're up to date, do you still get the 4261?

Similar Messages

  • I am the biggest "Newb" on this site,  and I really need some help please..

    Ok, the short of it.... I started training on Database programming about 2 weeks ago. I still don't really know a thing, or even understand the concepts. Now, my boss wants me to fix a bug in Oracle, and I haven't a clue. The ONLY help I've gotten was a link to this forum, and a speech about how I need to help myself. I told him I have the same chance of fixing anything, as monkeys typing hamlet. Anyone up for a challenge?
    When I go to Application System, then Application Entry and enter the password a dialog box appears.... "FRM-40039: Cannot attatch library Empower while opening from APPUSRAPP."
    That's what I have to fix. I have no clue. I don't even really know how to click around in this program. Please help, someone.
    UPDATE: I've been told that everyone's pretty much going to be a jerk to me for asking this, and I'm currently searching old threads and can't find a way to delete this one I posted. So, you could just ignore the post, or jump in and be the internet tough-guy and tell me what I already know.... I'm a newb.
    Edited by: user11033020 on Apr 14, 2009 11:41 AM

    As this appears to be a Forms error (the error begins with FRM) you might get a better response by posting this in the Forms forum:
    Forms
    The Community Feedback forum isn't meant for product-related questions (as it says in the title).
    Still, you should consider searching Metalink as well. If you've paid for support, you have every right to use it.

  • Pulling out my Hair, need some help from experts out there

    Hi - I have been struggling with an issue for a week now and I was wondering if one of you can help me to solve my issue. I have done numerous searches on this topic which got me somewhat in the right direction but I'm still not getting the results I want. The end objective is simple, a non-stuttering video on YouTube. Sounds simple right?
    here is what I did:
    I have recorded some aerial footage with a GoPro 3+, added some effects in After effects, brought the results over in Premiere pro for some minor editing and then used Media encoder to get it to a format that youtube likes. My detailed steps are as follows:
    -Take GoPro footage (59.94 fps, 1920 x 1080 in H.264 codec) and transcode it through GoPro studio using the CineForm codec so it plays nice with AE (I keep my 59.94 fps and same dimensions (1920 x 180).
    -Load transcoded footage in AE (I checked if my composition settings are the same as the imported transcoded footage)
    -Apply effects (3d camera tracking, add some 3d text, some lights, environment layer) and render the clip out as a quicktime lossless file (PNG) – result is 3 clips from AE that I now want to bring into Premiere Pro for some editing
    -Import PNG file in Premiere Pro (I drag the clip to new sequence item so the sequence matches the clip I import in Premiere pro)
    -I make some minor edits in Premiere Pro (some transitions between clips, nothing fancy)
    -I then render out the footage using media encoder (or directly from Premiere, tried both) with the following settings:
    Format: h.264
    Preset: custom
    Export video and audio
    TV standard: NSTC
    Frame width: 1920
    Frame height: 1080
    FPs: 29.97 or 59.94 (results/problem is the same with both fps settings)
    Field order: progressive (greyed out – can’t change it)
    Pixel aspect ratio: 16:9 – widescreen
    Profile: main
    Level: 4.2 or 5.1 (same result for both settings)
    Render at maximum depth: checked
    Bitrate encoding: VBR, 2 pass
    Target bitrate: 8 or 20 (same result with both settings but obviously larger file with higher target rate)
    Maximum bitrate: 8 or 25 (same results for both settings)
    Use maximum render quality: checked
    Audio, multiplexer etc: standard settings, no change
    The rendered video runs smoothly on my mac but when uploading this video to youtube, the video stutters. I have tried multiple settings and can’t get the video to play smooth. Any tips or suggestions are welcome!
    You can watch the video here:
    Furnace lake edit 1 - YouTube
    Thanks.

    sanderx1 wrote:
    Hi - I have been struggling with an issue for a week now and I was wondering if one of you can help me to solve my issue. I have done numerous searches on this topic which got me somewhat in the right direction but I'm still not getting the results I want. The end objective is simple, a non-stuttering video on YouTube. Sounds simple right?
    Thanks.
    Rick has given you what you need, he always does.
    But the task you've described is not simple at all. It's not really an After Effects issue.
    There are many sites that offer good recommendations for maximizing your youtube workflow so your video looks the best and plays flawlessly. Youtube offers a good set of parameters. Some of this stuff is worthless, too. You've got to be selective.
    Starting out delivering a full 1080HD clip is not necessarily going to work out for you. Try rendering out to a 720 file. It's far smaller so it will be compressed much less by it's upload processor. The playback may be smoother and your audience is not going to be able to tell the difference between the 720 and a 1080 clip, most of the time. 
    Encourage you to drop back someday and let us know how you made out with Rick's advice.
    How to Make Professional Quality YouTube Videos: 6 Steps
    How to Make Good YouTube Videos for Video Marketing: 8 Steps
    How To Make Videos Look Great on YouTube - YouTube
    How to Make YouTube Videos Look Great
    Video quality - YouTube Help
    Tips of Getting Best YouTube Video Format for YouTube Uploading

  • Need some help from the management : A deeply dissatisfied customer

    Hi,
    I hope I am one of the very dissatisfied customers of you company. I bought a new T715 and it has already gone for a repair twice. I gave it for repair for the first time in october (ETA was 20 days and told by the service centre) and I got the phone after some 30days only after an intervention of a manager. Prior to that the customer care was saying that they do not have the parts and they have no idea about how much time the repair is gonna take. Surprisingly it took only 2day once the manager intervened.
    When I was submitting the phone on jan 14th 2011(work order number SE311MM110015), they again said that I'll get my phone back in 20 days. This time I expected that the service center guys will learn some thing from the past incidents and provide me a better service. But this time it was even worse. I did not hear from them for 35 days. So I called the customer care and had a long conversation with them on the service that is being provided but no-one including the floor supervisor(nishant) had a clue about what happening with my phone. I was startled by thier reply that they will start working on it as I have registered the complaint. Then I asked them what were they doing till now for which they had no idea. I asked for an escalation of this case to a manager which they refused. They said that I'll get an update after 48 working hours(5days).
    The episode continues. I called the help desk after 5days. Now their reply is that I will get my phone back on march 10 2011. So, it is some 57 days since the day i submitted the phone which is 3 times the ETA they promosed. Now when I ask them why is it taking so long I get the same reply as I got for the first time that they do not have parts. The I told them I cannot accept this kind of service from a company like sony erricsson for the second time. For this the floor supervisor harish said that If I want my phone back earlier they'll return the piece back to me without repairing and they are not responsible for this. This time I again asked for a managerial escalation which they again refused and asked me to call after 2 days. Can I atleast hope for a positive reply this time??
    I am perfectly okay with one device out of a lakh being defective. I understand this is the reason that you provide the customers a warranty. But I have some issues with the support which you are providing:
    1) Managerial escalations : I think I am entitled to talk to some one who can actually solve my issue when the lower level doesn't solve it in time. I do not understand why I am being denied the escalation which I did not find in any other support. They do not even provide me an email ID of a manager.
    2) Support process : What is the use of those processes in place where the people I am talking have no idea of what the next step should be. They do not have the database or knowledge of the previous cases. Even the floor supervisor have no aswers to the legitamate questions that the customer poses, they talk as if they are not responsible for these issues.
    3) Time taken: Taking some  days to provide the customer a mere update is not how a 21st century support should work.
    I hope you people agree with my ideas. And please I request all the managers who stumble upon this thread to reply and guide me about my next action.
    Thanks and Regards
    PRakash Josyula
    Work order number : SE311MM110015

    @management : Please help me... I did not get my phone back yet... this time they were saying that they will investigate into this case and this process can take 10 more days... When I asked for a manager escalation they dropped the call... And surprisingly they started dropping my calls which is not at all acceptable...
    Please managers... I need to talk to you... I need my phone back repaired....
    @others... Please lemme know a contact of a person in managerial cadre if you are ware of one...
    Plleeeeeeeeeeeeeeeeeeeeeeeeeese

  • GS60 2PE Hopeless really need some help here!!!

    Hey MSIer, I just did a complete wipe on my hard drive and  now there's totally nothing left on the drive like really nothing so what I wanna ask is that how do I get back all the pre installed software including windows 8.1 itself, how?
    Does anyone out there don't mind taking some time to help list down a guide on how to get back to how the laptop originally was(all the pre installed software including windows 8.1 iitself)? Your help is really much much much muchhhh appreciated!!! T_T

    Quote from: Syrellaris;112053
    You should be able to restore using the Recovery Discs you made(if you made them..) or by pressing the F3 key during bootup.
    Though, if you wiped all partitions on the hard drive, including the normally hidden recovery partition you are kind of screwed.. in that case you need to send it in for repair, but it will not be fixed under warranty.(if you dont have Recovery disc's)
    Quote from: JakeSully;112055
    Yeah best option when getting a new laptop it is to create a recovery dic or USB recovery and atleast .iso recovery to that way incase you wipe everything on hard disk you can restore every partitions that was wiped including recovery partition that has copy of windows 8.1 64 bit that comes pre-installed.
    I didn't do any recovery disc and have yet to try the F3 button that you mention. So let say even if the F3 is not working I'm totally screwed right?

  • Storage:  I got a 32gig iPad for Christmas - I really need some help.

    Storage:  I got a 32gig iPad for Christmas, and literally I am already down to 2 gigs of storage left.  I believe my iPad is a 4th generation, and currently on my device I only have a 10 apps, 6 photos, 3 personal family videos 10mins in length each, and about 10 disney channel tv shows for my kids.  I also have my work email, but I set it to only go back two weeks. 
    I am not sure what I am doing to eat through this much space so quickly.  I realized after downloading 4 tv shows for my daughter I was getting HD, so I did change the other 6 to SD which I know takes less space.  However it hasn't really helped.  Recently I started using the camera to take a few short movies of my kids 3 videos about ten mins in length each and that ate through space in no time.
    My iPad is 32gigs but really only started with 28 gigs capacity. 
    Is there something I can do?  Am I doing something wrong?  Sorry I am not the most technically inclined, but a co-worker of mine has an older iPad with thousands of pics, hundreds of songs, plenty of movies, at least 20 apps, etc and her 32 gig iPad still has 12 gigs left.  She has WAY more stuff on hers than mine.
    I really appreciate any help someone can provide.  Thank You.  

    Ok. Do you know if I delete a show from iTunes on my device can I still redownload it for free?  Seems that 13.7 gigs taken up are those disney channel shows.  If I delete them I can always just redownload them no? 
    I appreciate your help.  Thanks.

  • Fried RAM slot?  Really need some help quick.

    Hi guys. I have a major problem on my hands, that I hope you may be able to help me solve...
    I have been working on a deadline for the production of a DVD that will be used as part of a mental health outreach program, and all had seemingly been going well, albeit slow with my OEM 512MB of RAM. I therefore decided to upgrade my RAM, first buying two 512MB DIMMS from macsolutuons, but these DIMMS produced crashes almost religiously after 5 or so minutes of uptime. After receiving a new shipment, ensuring they were from the same batch, all seemed to be well. The computer stayed up for days without crash - but when I put a load on it, namely video encoding to DV stream and to MPEG-2, poof - hard crashes.
    I decided the RAM from macsolutions looked generic and suspected if I bought some real RAM I'd be safe. I purchased Viking RAM form macmall, three 512MB DIMMS, overnighted so I can make this deadline.
    Here's the catch...
    If I use all three DIMMS, the computer crashes in less than 5 minutes of uptime religiously. If I use two of them, the computer seems to stay up without problems, but when it sees a load like video conversion places on the system, it locks up. When I remove all RAM, so only one 512MB DIMM is present, I can encode video, and I don't seem to get crashes.
    When I bought the machine from Apple some two years ago, it came with one 512MB DIMM. I'm only hypothesizing here, but is there a chance that I received a machine that has a RAM slot 1 that's fine, but there's something wrong with slot 2 (or even 2, 3, 4)? In theory, when just surfing or using standard apps, the first slot meets the RAM need, but when more RAM allocation is needed under hard processes, and the system feeds off of slots beyond #1, then I crash. MenuMeters is installed so I can monitor RAM use, and sure enough, I mainly get crashes as my used RAM approaches 480-500MB.
    It's really urgent that I get to the bottom of this issue sooner than later, so I can finish this project to meet my deadline. Assuming slot 2 and so forth are bad, could I use a single 1GB DIMM module?
    Any advice is greatly appreciated. If i can repay the favor in any way, I'd be glad to.

    I suspected the RAM as well, however when I use only one DIMM I get zero crashes. I have used each of the three DIMMS for one day each now, and no crashes, but the second I add another ino the configuration crashes occur. While I agree that cheap RAM is often the culprit, to me all signs point to a faulty slot 2.
    I think I'll try getting a 1G RAM DIMM and only use slot 1 and see how that goes. Too bad, because I could really use more than 1G.

  • HELP! I need some help from true Mac fans! What should I buy???

    So, I'm moving to Japan, which has a couple of implications (other than the fact that my wife's parents and my parents are looking for any legal recourse to stop us from taking their only grandchild out of the country). More importantly however, I have had to sell my B&O TV and music system (different signals from the UK where we now live). I also decided to sell our stereo (or rather my wife decided it was too bulky so as long as it was not in the living room or bedroom I could keep it...). Finally, I need a new laptop for personal use. I have some friends that are absolute mac fans, who have convinced me to go over to the other side (i.e. yours).
    The opportunity I now have is to create a complete system as I need a laptop, something to play my music, a TV, etc. Given I am starting from a clean sheet I was hoping somebody out there could help me 'design' a complete set-up. My wife and I are keen photographers (both photography and video), we like listening to music, and watching movies (we definitely need a region-free DVD player), so what should we buy?
    Any input would be hugely appreciated.

    OSX also supports IME right out of the box.
    日本語 ー わかりません
    It sets up pretty well, too; I like it more than Mircrosoft's implementation (language bar).
    Only thing to keep in mind is where you buy the MacBook; if you get it in Japan you'll get a Japanese keyboard, which displays most of the kana alongside the keys. You also get the conversion and switch keys on the keyboard itself, which is great.
    The MacBook Power Unit is multi-voltage, so no matter where you pick it up the worst you need is a plug adapter; although getting one from apple would be best. Just don't think you need to buy a new power unit, only the plug and cable.

  • Ok I REALLY need some help

    Please post anyhting you can to help me out, I've had this ipod for so long now... and recently itunes has just been being incredibly stupid for me. So here is how it all began, few days ago i connect my ipod... and it auto syncs it, even when that function was turned off... replacing all of my music with the ones in my library ( completely different) k few days later i turn it on again, i got a new HD recently since my old one busted and i redownload itunes v8 and i cant put songs on my ipod. I try and put one on and it automatically puts it in my normal Itunes library, then in the shuffle playlist all you see is this 1 song being duplicated 111 times.... so now this Itunes has deleted over 30 GB of info off my ipod... all movies and songs.. so its completely clean which really makes me angry. I can't fix this.. i dont know what this is.. please help me >< i have already tried reinstalling it, unless there is some sort of function in options to actually get my god dan songs on without them duplicated 100 times and get this ipod working agian please I need help... i've spent all my day trying to fix this.. thanks for your feedback

    I know this is a IPod forum
    Actually it's not. It's a forum for feedback about Apple's discussions forums, as the title implies. I suggest you post your message again here:
    http://discussions.apple.com/forum.jspa?forumID=800

  • Really Need Some Help with CME 8.6 using IOS as Firewall and Anyconnect VPN on Phones

    Hello,
    I have a 2911 Router with IOS Security and Voice enabled and we are using CME 8.6.  I am using a built-in Anyconnect VPN on 3 phones that are for remote users and thus I needed to enable security zones on the router which works because the remote phones will boot up, get their phone configs and I am able to call those remote phones from an outside line.
    The issue I am having is that when I try to dial a remote phone connected via the VPN through port g0/0 from and internal office phone, i.e., NOT involving the PSTN then there is no audio.  It's as if no audio is going back and forth.  When I take off the security zones from the virtual-template interface and the g0/0 interface then the audio works great and I can reach the phone from internal as I am supposed to.
    Could someone take a peek at my security config and see why audio would not be traveling through the VPN when I have my security zones turned on?
    clock timezone PST -8 0
    clock summer-time PST recurring
    network-clock-participate wic 0 
    network-clock-select 1 T1 0/0/0
    no ipv6 cef
    ip source-route
    ip cef
    ip dhcp excluded-address 192.168.8.1 192.168.8.19
    ip dhcp pool owhvoip
     network 192.168.8.0 255.255.248.0
     default-router 192.168.8.1 
     option 150 ip 192.168.8.1 
     lease 30
    multilink bundle-name authenticated
    isdn switch-type primary-ni
    crypto pki server cme_root
     database level complete
     grant auto
     lifetime certificate 7305
     lifetime ca-certificate 7305
    crypto pki token default removal timeout 0
    crypto pki trustpoint cme_root
     enrollment url http://192.168.8.1:80
     revocation-check none
     rsakeypair cme_root
    crypto pki trustpoint cme_cert
     enrollment url http://192.168.8.1:80
     revocation-check none
    crypto pki trustpoint TP-self-signed-2736782807
     enrollment selfsigned
     subject-name cn=IOS-Self-Signed-Certificate-2736782807
     revocation-check none
     rsakeypair TP-self-signed-2736782807
    voice-card 0
     dspfarm
     dsp services dspfarm
    voice service voip
     allow-connections h323 to h323
     allow-connections h323 to sip
     allow-connections sip to h323
     allow-connections sip to sip
     fax protocol t38 version 0 ls-redundancy 0 hs-redundancy 0 fallback none
     vpn-group 1
      vpn-gateway 1 https://66.111.111.111/SSLVPNphone
      vpn-trustpoint 1 trustpoint cme_cert leaf
     vpn-profile 1
      host-id-check disable
    voice class codec 1
     codec preference 1 g711ulaw
    voice class custom-cptone jointone
     dualtone conference
      frequency 600 900
      cadence 300 150 300 100 300 50
    voice class custom-cptone leavetone
     dualtone conference
      frequency 400 800
      cadence 400 50 200 50 200 50
    voice translation-rule 1
     rule 1 /9400/ /502/
     rule 2 /9405/ /215/
     rule 3 /9410/ /500/
    voice translation-rule 2
     rule 1 /.*/ /541999999/
    voice translation-rule 100
     rule 1 /^9/ // type any unknown plan any isdn
    voice translation-profile Inbound_Calls_To_CUE
     translate called 1
    voice translation-profile InternationalType
     translate called 100
    voice translation-profile Local-CLID
     translate calling 2
    license udi pid CISCO2911/K9 sn FTX1641AHX3
    hw-module pvdm 0/0
    hw-module pvdm 0/1
    hw-module sm 1
    username routeradmin password 7 091649040910450B41
    username cmeadmin privilege 15 password 7 03104803040E375F5E4D5D51
    redundancy
    controller T1 0/0/0
     cablelength long 0db
     pri-group timeslots 1-12,24
    class-map type inspect match-any sslvpn
     match protocol tcp
     match protocol udp
     match protocol icmp
    class-map type inspect match-all router-access
     match access-group name router-access
    policy-map type inspect firewall-policy
     class type inspect sslvpn
      inspect 
     class class-default
      drop
    policy-map type inspect outside-to-router-policy
     class type inspect router-access
      inspect 
     class class-default
      drop
    zone security trusted
    zone security internet
    zone-pair security trusted-to-internet source trusted destination internet
     service-policy type inspect firewall-policy
    zone-pair security untrusted-to-trusted source internet destination trusted
     service-policy type inspect outside-to-router-policy
    interface Loopback0
     ip address 192.168.17.1 255.255.248.0
    interface Embedded-Service-Engine0/0
     no ip address
     shutdown
    interface GigabitEthernet0/0
     description Internet
     ip address dhcp
     no ip redirects
     no ip proxy-arp
     zone-member security internet
     duplex auto
     speed auto
    interface GigabitEthernet0/1
     ip address 192.168.8.1 255.255.248.0
     duplex auto
     speed auto
    interface GigabitEthernet0/2
     no ip address
     shutdown
     duplex auto
     speed auto
    interface Serial0/0/0:23
     no ip address
     encapsulation hdlc
     isdn switch-type primary-ni
     isdn incoming-voice voice
     no cdp enable
    interface Integrated-Service-Engine1/0
     ip unnumbered Loopback0
     service-module ip address 192.168.17.2 255.255.248.0
     !Application: CUE Running on NME
     service-module ip default-gateway 192.168.17.1
     no keepalive
    interface Virtual-Template1
     ip unnumbered GigabitEthernet0/0
     zone-member security trusted
    ip local pool SSLVPNPhone_pool 192.168.9.1 192.168.9.5
    ip forward-protocol nd
    ip http server
    ip http authentication local
    no ip http secure-server
    ip http path flash:/cme-gui-8.6.0
    ip route 192.168.17.2 255.255.255.255 Integrated-Service-Engine1/0
    ip access-list extended router-access
     permit tcp any host 66.111.111.111 eq 443
    tftp-server flash:apps31.9-3-1ES26.sbn
    control-plane
    voice-port 0/0/0:23
    voice-port 0/3/0
    voice-port 0/3/1
    mgcp profile default
    sccp local GigabitEthernet0/1
    sccp ccm 192.168.8.1 identifier 1 priority 1 version 7.0 
    sccp
    sccp ccm group 1
     bind interface GigabitEthernet0/1
     associate ccm 1 priority 1
     associate profile 1 register CME-CONF
    dspfarm profile 1 conference  
     codec g729br8
     codec g729r8
     codec g729abr8
     codec g729ar8
     codec g711alaw
     codec g711ulaw
     maximum sessions 4
     associate application SCCP
    dial-peer voice 500 voip
     destination-pattern 5..
     session protocol sipv2
     session target ipv4:192.168.17.2
     dtmf-relay sip-notify
     codec g711ulaw
     no vad
    dial-peer voice 10 pots
     description Incoming Calls To AA
     translation-profile incoming Inbound_Calls_To_CUE
     incoming called-number .
     port 0/0/0:23
    dial-peer voice 20 pots
     description local 10 digit dialing
     translation-profile outgoing Local-CLID
     destination-pattern 9[2-9].........
     incoming called-number .
     port 0/0/0:23
     forward-digits 10
    dial-peer voice 30 pots
     description long distance dialing
     translation-profile outgoing Local-CLID
     destination-pattern 91..........
     incoming called-number .
     port 0/0/0:23
     forward-digits 11
    dial-peer voice 40 pots
     description 911
     destination-pattern 911
     port 0/0/0:23
     forward-digits all
    dial-peer voice 45 pots
     description 9911
     destination-pattern 9911
     port 0/0/0:23
     forward-digits 3
    dial-peer voice 50 pots
     description international dialing
     translation-profile outgoing InternationalType
     destination-pattern 9T
     incoming called-number .
     port 0/0/0:23
    dial-peer voice 650 pots
     huntstop
     destination-pattern 650
     fax rate disable
     port 0/3/0
    gatekeeper
     shutdown
    telephony-service
     protocol mode ipv4
     sdspfarm units 5
     sdspfarm tag 1 CME-CONF
     conference hardware
     moh-file-buffer 90
     no auto-reg-ephone
     authentication credential cmeadmin tshbavsp$$4
     max-ephones 50
     max-dn 200
     ip source-address 192.168.8.1 port 2000
     service dnis dir-lookup
     timeouts transfer-recall 30
     system message Oregon's Wild Harvest
     url services http://192.168.17.2/voiceview/common/login.do 
     url authentication http://192.168.8.1/CCMCIP/authenticate.asp  
     cnf-file location flash:
     cnf-file perphone
     load 7931 SCCP31.9-3-1SR4-1S.loads
     load 7936 cmterm_7936.3-3-21-0.bin
     load 7942 SCCP42.9-3-1SR4-1S.loads
     load 7962 SCCP42.9-4-2-1S.loads
     time-zone 5
     time-format 24
     voicemail 500
     max-conferences 8 gain -6
     call-park system application
     call-forward pattern .T
     moh moh.wav
     web admin system name cmeadmin secret 5 $1$60ro$u.0r/cno/OD2JmtvPq4w9.
     dn-webedit 
     transfer-digit-collect orig-call
     transfer-system full-consult
     transfer-pattern .T
     fac standard
     create cnf-files version-stamp Jan 01 2002 00:00:00
    ephone-template  1
     softkeys connected  Hold Park Confrn Trnsfer Endcall ConfList TrnsfVM
     button-layout 7931 2
    ephone-template  2
     softkeys idle  Dnd Gpickup Pickup Mobility
     softkeys connected  Hold Park Confrn Mobility Trnsfer TrnsfVM
     button-layout 7931 2
    ephone-dn  1  dual-line
     number 200
     label Lisa
     name Lisa Ziomkowsky
     call-forward busy 500
     call-forward noan 500 timeout 10
    ephone-dn  2  dual-line
     number 201
     label Dylan
     name Dylan Elmer
     call-forward busy 500
     call-forward noan 500 timeout 12
    ephone-dn  3  dual-line
     number 202
     label Kimberly
     name Kimberly Krueger
     call-forward busy 500
     call-forward noan 500 timeout 10
    ephone-dn  4  dual-line
     number 203
     label Randy
     name Randy Buresh
     mobility
     snr calling-number local
     snr 915035042317 delay 5 timeout 15 cfwd-noan 500
     call-forward busy 500
     call-forward noan 500 timeout 12
    ephone-dn  5  dual-line
     number 204
     label Mark
     name Mark McBride
     call-forward busy 500
     call-forward noan 500 timeout 10
    ephone-dn  6  dual-line
     number 205
     label Susan
     name Susan Sundin
     call-forward busy 500
     call-forward noan 500 timeout 10
    ephone-dn  7  dual-line
     number 206
     label Rebecca
     name Rebecca Vaught
     call-forward busy 500
     call-forward noan 500 timeout 10
    ephone-dn  8  dual-line
     number 207
     label Ronnda
     name Ronnda Daniels
     call-forward busy 500
     call-forward noan 500 timeout 10
    ephone-dn  9  dual-line
     number 208
     label Matthew
     name Matthew Creswell
     call-forward busy 500
     call-forward noan 500 timeout 10
    ephone-dn  10  dual-line
     number 209
     label Nate
     name Nate Couture
     call-forward busy 500
     call-forward noan 500 timeout 10
    ephone-dn  11  dual-line
     number 210
     label Sarah
     name Sarah Smith
     call-forward busy 500
     call-forward noan 500 timeout 10
    ephone-dn  12  dual-line
     number 211
     label Janis
     name Janis McFerren
     call-forward busy 500
     call-forward noan 500 timeout 12
    ephone-dn  13  dual-line
     number 212
     label Val
     name Val McBride
     call-forward busy 500
     call-forward noan 500 timeout 10
    ephone-dn  14  dual-line
     number 213
     label Shorty
     name Arlene Haugen
     call-forward busy 500
     call-forward noan 500 timeout 10
    ephone-dn  15  dual-line
     number 214
     label Ruta
     name Ruta Wells
     call-forward busy 500
     call-forward noan 500 timeout 10
    ephone-dn  16  dual-line
     number 215
     label 5415489405
     name OWH Sales
     call-forward busy 500
     call-forward noan 500 timeout 12
    ephone-dn  17  dual-line
     number 216
     call-forward busy 500
     call-forward noan 500 timeout 10
    ephone-dn  18  dual-line
     number 217
     call-forward busy 500
     call-forward noan 500 timeout 12
    ephone-dn  19  dual-line
     number 218
     call-forward busy 500
     call-forward noan 500 timeout 12
    ephone-dn  20  dual-line
     number 219
     call-forward busy 500
     call-forward noan 500 timeout 12
    ephone-dn  21  dual-line
     number 220
     call-forward busy 500
     call-forward noan 500 timeout 10
    ephone-dn  22  dual-line
     number 221
     call-forward busy 500
     call-forward noan 500 timeout 10
    ephone-dn  23  dual-line
     number 222
     label Pam
     name Pam Buresh
     call-forward busy 500
     call-forward noan 500 timeout 12
    ephone-dn  24  dual-line
     number 223
     call-forward busy 500
     call-forward noan 500 timeout 12
    ephone-dn  25  dual-line
     number 224
     call-forward busy 500
     call-forward noan 500 timeout 12
    ephone-dn  26  dual-line
     number 225
     label Elaine
     name Elaine Mahan
     call-forward busy 500
     call-forward noan 500 timeout 10
    ephone-dn  27  octo-line
     number 250
     label Shipping
     name Shipping
    ephone-dn  28  dual-line
     number 251
     label Eli
     name Eli Nourse
     call-forward busy 500
     call-forward noan 500 timeout 10
    ephone-dn  29  dual-line
     number 252
    ephone-dn  30  dual-line
     number 253
    ephone-dn  31  octo-line
     number 100
     label Customer Service
     name Customer Service
     call-forward busy 500
     call-forward noan 500 timeout 12
    ephone-dn  32  octo-line
     number 101
     label Sales
     name Sales
     call-forward busy 214
     call-forward noan 214 timeout 12
    ephone-dn  33  dual-line
     number 260
     label Conference Room
     name Conference Room
     call-forward busy 100
     call-forward noan 100 timeout 12
    ephone-dn  100
     number 300
     park-slot timeout 20 limit 2 recall
     description Park Slot For All Company
    ephone-dn  101
     number 301
     park-slot timeout 20 limit 2 recall
     description Park Slot for All Company
    ephone-dn  102
     number 302
     park-slot timeout 20 limit 2 recall
     description Park Slot for All Company
    ephone-dn  103
     number 700
     name All Company Paging
     paging ip 239.1.1.10 port 2000
    ephone-dn  104
     number 8000...
     mwi on
    ephone-dn  105
     number 8001...
     mwi off
    ephone-dn  106  octo-line
     number A00
     description ad-hoc conferencing
     conference ad-hoc
    ephone-dn  107  octo-line
     number A01
     description ad-hoc conferencing
     conference ad-hoc
    ephone-dn  108  octo-line
     number A02
     description ad-hoc conferencing
     conference ad-hoc
    ephone  1
     device-security-mode none
     mac-address 001F.CA34.88AE
     ephone-template 1
     max-calls-per-button 2
     paging-dn 103
     type 7931
     button  1:2 2:31
    ephone  2
     device-security-mode none
     mac-address 001F.CA34.8A03
     ephone-template 1
     max-calls-per-button 2
     paging-dn 103
     type 7931
     button  1:12
    ephone  3
     device-security-mode none
     mac-address 001F.CA34.898B
     ephone-template 1
     max-calls-per-button 2
     paging-dn 103
     type 7931
    ephone  4
     device-security-mode none
     mac-address 001F.CA34.893F
     ephone-template 1
     max-calls-per-button 2
     paging-dn 103
     type 7931
    ephone  5
     device-security-mode none
     mac-address 001F.CA34.8A71
     ephone-template 1
     max-calls-per-button 2
     username "susan"
     paging-dn 103
     type 7931
     button  1:6
    ephone  6
     device-security-mode none
     mac-address 001F.CA34.8871
     ephone-template 1
     max-calls-per-button 2
     paging-dn 103
     type 7931
     button  1:7 2:31 3:32
    ephone  7
     device-security-mode none
     mac-address 001F.CA34.8998
     ephone-template 1
     max-calls-per-button 2
     username "matthew"
     paging-dn 103
     type 7931
     button  1:9
    ephone  8
     device-security-mode none
     mac-address 001F.CA36.8787
     ephone-template 1
     max-calls-per-button 2
     username "nate"
     paging-dn 103
     type 7931
     button  1:10
    ephone  9
     device-security-mode none
     mac-address 001F.CA34.8805
     ephone-template 1
     max-calls-per-button 2
     paging-dn 103
     type 7931
     button  1:5
    ephone  10
     device-security-mode none
     mac-address 001F.CA34.880C
     ephone-template 1
     max-calls-per-button 2
     paging-dn 103
     type 7931
     button  1:14
    ephone  11
     device-security-mode none
     mac-address 001F.CA34.8935
     ephone-template 1
     max-calls-per-button 2
     paging-dn 103
     type 7931
     button  1:3
    ephone  12
     device-security-mode none
     mac-address 001F.CA34.8995
     ephone-template 1
     max-calls-per-button 2
     paging-dn 103
     type 7931
     button  1:8 2:31
    ephone  13
     device-security-mode none
     mac-address 0021.5504.1796
     ephone-template 2
     max-calls-per-button 2
     paging-dn 103
     type 7931
     button  1:4
    ephone  14
     device-security-mode none
     mac-address 001F.CA34.88F7
     ephone-template 1
     max-calls-per-button 2
     paging-dn 103
     type 7931
     button  1:23
    ephone  15
     device-security-mode none
     mac-address 001F.CA34.8894
     ephone-template 1
     max-calls-per-button 2
     paging-dn 103
     type 7931
     button  1:26
    ephone  16
     device-security-mode none
     mac-address 001F.CA34.8869
     ephone-template 1
     max-calls-per-button 2
     paging-dn 103
     type 7931
     button  1:28 2:27
    ephone  17
     device-security-mode none
     mac-address 001F.CA34.885F
     ephone-template 1
     max-calls-per-button 2
     paging-dn 103
     type 7931
     button  1:11
    ephone  18
     device-security-mode none
     mac-address 001F.CA34.893C
     ephone-template 1
     max-calls-per-button 2
     paging-dn 103
     type 7931
     button  1:27
    ephone  19
     device-security-mode none
     mac-address 001F.CA34.8873
     ephone-template 1
     max-calls-per-button 2
     paging-dn 103
     type 7931
     button  1:27
    ephone  20
     device-security-mode none
     mac-address A456.3040.B7DD
     paging-dn 103
     type 7942
     vpn-group 1
     vpn-profile 1
     button  1:13
    ephone  21
     device-security-mode none
     mac-address A456.30BA.5474
     paging-dn 103
     type 7942
     vpn-group 1
     vpn-profile 1
     button  1:15 2:16 3:32
    ephone  22
     device-security-mode none
     mac-address A456.3040.B72E
     paging-dn 103
     type 7942
     vpn-group 1
     vpn-profile 1
     button  1:1
    ephone  23
     device-security-mode none
     mac-address 00E0.75F3.D1D9
     paging-dn 103
     type 7936
     button  1:33
    line con 0
    line aux 0
    line 2
     no activation-character
     no exec
     transport preferred none
     transport input all
     transport output pad telnet rlogin lapb-ta mop udptn v120 ssh
     stopbits 1
    line 67
     no activation-character
     no exec
     transport preferred none
     transport input all
     transport output pad telnet rlogin lapb-ta mop udptn v120 ssh
    line vty 0 4
     transport input all
    scheduler allocate 20000 1000
    ntp master
    ntp update-calendar
    ntp server 216.228.192.69
    webvpn gateway sslvpn_gw
     ip address 66.111.111.111 port 443  
     ssl encryption 3des-sha1 aes-sha1
     ssl trustpoint cme_cert
     inservice
    webvpn context sslvpn_context
     ssl encryption 3des-sha1 aes-sha1
     ssl authenticate verify all
     policy group SSLVPNphone
       functions svc-enabled
       hide-url-bar
       svc address-pool "SSLVPNPhone_pool" netmask 255.255.248.0
       svc default-domain "bendbroadband.com"
     virtual-template 1
     default-group-policy SSLVPNphone
     gateway sslvpn_gw domain SSLVPNphone
     authentication certificate
     ca trustpoint cme_root
     inservice
    end

    I think your ACL could be the culprit.
    ip access-list extended router-access
     permit tcp any host 66.111.111.111 eq 443
    Would you be able to change the entry to permit ip any any (just for testing purpose) and then test to see if the calls function properly.  If they work fine then we know that we need to open som ports there.
    Please remember to select a correct answer and rate helpful posts

  • REALLY need some help with my problem (Netgear and...

    Hi everyone,
    Well... where to start really.
    This morning around 5am, I lost connection to the net, yet my Netgear (DG834 wired) showed an uptime of 117 hours, so it showed no reboot. It seems my IP profile was raised (As it was low before for my sync).
    I had no reboot it seems, but my noise margin went up to 9db from 6db. This is fine as it means I should be getting around 6.5meg IP profile going by the sync. Anyway (This is complicated to explain but bear with me).
    My current IP profile is now 7.15K. I know this will come down now to match my sync at 9db (Which should be 6.5meg).
    What is happening, is that any change made to my broadband (Like my IP profile being raised this morning) means that I cannot then connect to the net, and anything connected (Like Xbox Live etc) disconnects, even though the router shows no disconnect, and all the lights are green.
    The only way for me to reconnect to the internet then is to MANUALLY reboot the router, because no matter what website etc I try to view, it just says "Looking for..." in the bottom left corner of the browser, and I can't connect to anything like Xbox Live etc.
    Can anyone explain why this is happening with the Netgear router? Shouldn't any change, like an IP profile increase not affect my broadband connection? It seems whenever a change is made BT side, I have to then manually reboot the router to get online.
    I wondered if anyone with a netgear, or anyone with some knowledge on this could tell me why. This could save me a lot of headaches down the line and stop me having noise margin raised etc because I have to manually reboot the router to get it working again. I just thought that any change, like an increase in IP profile etc, shouldn't affect my connnection and force me to have to manually reboot the router to get it up and running again.
    I hope you understood what I was trying to explain, and thanks in advance for any responses.

    Hi John. Thanks for responding.
    I have been through the options on the router and can't find one that says auto connect at all.
    It seems the router is not disconnecting though (Like this morning when the IP profile raised), as the uptime on both WAN and LAN were showing 117 hours, and all green lights were on, on the router. It's just when a change on the BT side is made, it won't let me get on the net until I do a manual reboot. It's all very baffling to me really.
    I tried googling my problem to no avail also.

  • REALLY need some help with transparent background

    This is really starting to bug me now as I have searched the forums and the web for hours and still cannot get this to work.
    I am creating a simple one page site at http://freeselfhelpebooks.org/50ofTheBestPDProducts/
    I want the header and footer image to have a transparent background with only the text showing, so that the text shows on the background image.
    So far I have created the header image with a transparent background Modify > Canvas > Canvas Colour > Transparent all good so far.  I have added some text.  Then I save as file type PNG 32, however I still get the background as white as you can see above.
    I have tried PNG 8 with alpha transparency, no transparency but to no avail.  I have even downloaded Photoshop CS6 and have the same issues.  What am I doing wrong here?

    First of all, your header graphic is fine; it's a transparent PNG. Your footer is a JPEG, which does not support transparency, so you need to resave that file into a different format (like PNG32, or PNG8 w/alpha transparency).
    As I was trying to suggest, if you're confused about your graphics, check them in a graphics editor or viewer, not in a web page inside a web browser. Web development is a complex beast, and a lot can go wrong.
    In the HTML of your web page, there is a class called "content" being applied to tables and images. This class has a background image being applied to it, which is responsible for the white background on those elements.

  • I really need some help here....Please?

    Hey guys i have posted numerous threads regarding this issue but to no avail so im going to try one last time.
    Basically, Itunes works fine UNTIL i start to sync, Then it freezes up for a while then starts to sync a little bit...Then freezes and syncs a little bit..And so on..
    It took me 2 WHOLE days to sync 15 episodes of southpark.
    I transfered some movies and songs to my wifes laptop and it sync'd everything in around 50 seconds flat, So its now obvious that it must be my PC.
    I have USB 2 and i have 6 slots, I have tried ALL the different USB slots and it stays the same.
    Does anyone have ANY idea what this could be?
    I spoke to the guy who built my PC and he is changing the USB ports, He also said if that doesn't work he will change my motherboard..
    Is there a simple solution to this? Am i going to have to change Motherboard? ANY help would really be greatful.

    Hold your horses....
    Have you done some "rule out" testing? How do you know that the USBs are bad? How do you know that the MB is bad?
    1/ do all ports work when you plug a mouse in them?
    2/ what is a throughput when you plug a flash drive into these USBs (try 1 at a time) and copy a large file onto it? Test all the ports and compare speeds - are they at least 5-10 MB per sec? If yeah, then they are OK - system wise.
    If the USBs don't work and it's a PCI card, look for drivers and if no luck, buy a new card.
    If the USBs are built into the MB, then you have no other choice but to replace it, but only as the very last resort. Seems to me that he's trying ot hose you, my friend.....
    IN any case, it could be the drivers! Or..iTunes. Did you try to remove & reinstall?

  • Really need some help

    I am having trouble trying to delete Quick Times off of my computer. Everytime I go to control panel, add/remove programs, it will not let me do anything. I need help! I need to know how to go about fixing that problem and how to get it off my computer!!! If you can help at all please!!!!! I just need to delete the program and even when i try to open it up it will not let me, it keeps giving me some error message! Help me if you can!

    thank you! ok I am sorry that I am slow when it comes to computer porblems, but I installed the cleanup program and need help what to do next. I wne back and tried to delete the program and still the same problem. if you can help it would be great! thanks and have a great night, go bears!

  • Problems with the address book server! Really need some help here!

    Hello everyone!
    for about some time now, we're having some troubbles with the address book server located on our Mac Pro Server running SL Server. The connected clients somehow show multiple entries of groups, contacts and everything else address book can show. Sometimes you see one group or contact about 20-30 times or even more.
    How can the addressbook server on SL Server be configured that these faults won't show up again. With this present, using address book server is useless. As far as my knowledge goes, I've tried everything I can. I deleted the address book account set up on each client, readded it, but no help. I stopped the address book server on the Mac pro, but no help either.
    For your further information: we're connecting 14 clients. Moste of the rum Lion, three run ML and several iDevices connect via WiFi.
    Please help me, as this really is frustrating!
    Looking forward for your help.
    Regards,
    Moritz

    james211 wrote:
    I have been trying to convince my landlord for months to get Fios in the building.   
    If your landlord doesn't want FIOS in the building, then it's not going to happen.
    Vote with your wallet and move.

Maybe you are looking for

  • Java Heap Space Issues

    Greetings. I hope this is the right forum I have a project, a chess program, that makes use of some very large static arrays. As I experiment with increasing the size of the arrays, I eventually run into heap space out of memory errors when instantia

  • Dvd wont eject

    I have a mac pro I just had a replacement dvd drive installed the old one jammed up and the tray was stuck in open position. the new one was installed at my local apple store. It wont open when you press the eject button. But it only opens when you c

  • ORA-06502: PL/SQL: numeric or value error : Not able to run a script

    Hi All, I want to run a script like this: DECLARE I_so_status_dtl     RIB_SOStatusDtl_REC; BEGIN I_so_status_dtl := RIB_SOStatusDtl_REC('0'     --Cust Order No                ,'1000000014'     --Dest ID                ,'100010222'     --Item ID      

  • Runtime error "didn't find subcontext 'jdbc'."

    hi, what does it take to make this application run back on WebLogic? It's a bit boring testing applications on Glassfish... So i'd prefer all-stage-development in JDeveloper, then final deployment to Glassfish. I followed to Shay Shmeltzer blog's rec

  • Nexus galaxy

    I am having problems with the samsung nexus galaxy. It keeps resetting and I cannot do much. Every once in a while I can do something before it resets. Any ideas? Also when it resets, it resets to friday dec 31st at 4pm and it is only dec 27 like 10p