Error in LSMW (BIPKO-PRFIDNETZ)

Hi Experts,
I am getting a error at step 13 while creating Batch input session using LSMW as "No Profile with entry tool task list N 1 session ROUTING".
I tried to use the default value for BIPKO-PRFIDNETZ = (default value tht i was given).still it says same error.
Daniel

Here is the message shown by SAP:
--START MESSAGE
No profile with entry tool for task list / / / in session C_INSP_PLAN
Message no. CP855
Diagnosis
You did not enter a routing profile with the entry tool in the input file.
You cannot copy any operation data in batch input without using the entry tool.
Procedure
Maintain a profile in which the entry tool is activated in field BIPKO-PROFIDNETZ of the input file.
You make settings for the entry tool in the control data for routings within Customizing under Production -> Basic Data -> Routing -> Control Data -> Define profiles with default values.
Activate the entry tool
--END MESSAGE

Similar Messages

  • Error in LSMW while specifying file for Material Cassification and Info Rec

    Hi Friends,
    I'm getting an error in LSMW while specifying file for Material Cassification and Info Record using batch input method.
    The error message i'm getting is:
    "Length of physical file name 'R2R_33_PURCH_INFR_1_PIR_CREATE.lsmw.conv' cannot be longer than 30 characters
    Message no. /SAPDMC/LSMW_OBJ_060049"
    I tried changing the file name but that is not working out. Please help.
    Thanks,
    Amit

    Hi,
    Just try this,
    Go to LSMW, Specify file option, use display/change (Ctrl+F1)
    Select the converted data and double click, change the file name there,
    You will be getting it as "'R2R_33_PURCH_INFR_1_PIR_CREATE"
    Just trim this to "'R2R_33_PUR_INF_1_PIR_CRE"  and try...
    Regards
    Merwyn

  • Error in LSMW for ME11

    Hi,
    I am getting error while creating LSMW for ME11, No QM info record exists for vendor xxxx.
    How will I know for vendor QM info record to be maintained.
    Smitha

    this problem has actually nothing to do with LSMW, you get the same error without LSMW
    In your material master QM view is a control key, and based on the cusotmizing of the control key it requires a Q-info record.

  • Error in LSMW getting return code 6

    Hi all,
                 i Am getting a  Error in LSMW getting return code 6 , after asign a file , in the read data step i am getting the error , please help me it is very urgent,
    sridhar

    Hi,
    If the Sy-Subrc is 0 then Success, if the Sy-SUBRC is 4 then failure, if the Sy-SUBRC = 6 then the user might be not access to read the file
    AUTHORITY-CHECK sets SY-SUBRC to 0 if the user has the necessary authorization, otherwise 4, 8, 12, 16, 24, 28, 32, or 36 depending on the cause
    Regards
    Sudheer

  • Errors in LSMW

    Hi Experts,
    How can we handle errors in LSMW..(Using Batch input recording method in LSMW)..If any error comes will it allow to craete session?..
    Regards

    hi
    good
    LSMW creates a file of all the input records that failed. Look at the error log and see why it failed. Fix the problem (config/data/etc.) then reprocess the records that failed.
    thanks
    mrutyun^

  • Error in LSMW : Enter a Valid Value

    Dear All,
    I am Creating a LSMW for MM01 Transaction using Direct Batch Input Method
    I got an error in LSMW while I start uploading saying "Enter a Valid Value" .
    I am selecting 14 Views in a single LSMW.
    Basic Data1 / Data2 , Purchasing , Foreign Trade : Import Data, MRP1,2,3 , General Plant 1/2 , Accounting 1 & 2 , Costing 1 & 2.
    Can anybody tell me why I am getting that error.
    Thanks in Advance.
    Tulasi

    Perform theses steps
    - In LSMW read and convert only one entry from file
    - go to SM35 -> select your session with that one entry
    - select process , option process/foreground
    - choose process
    You will have that batch input run in the foreground, so you can see all the values entered to certain input fields and all the actions which take place in that screens. This way you should see which step excatly creates the error.
    Regards
    Marcin

  • Where to fix errors in lsmw?

    where to fix errors in lsmw?

    hi sunil
    refer the following link
    it will give u full step by step process for lsmw
    http://www.scmexpertonline.com/downloads/SCM_LSMW_StepsOnWeb.doc
    In the field mappings and conversion rules,
    in the global section,define an internal table.
    data : begin of it_errors occurs 0,
    desc type string,
    end of it_errors.
    and where ever you have wrong or empty values for the fields,populate error there to the internal table.
    for example, if Material no is blank,i have to give err msg
    IF NOT MATMAS_MRPVIEW-MATNR IS INITIAL.
    BMM00-MATNR = MATMAS_MRPVIEW-MATNR.
    else.
    IT_ERROR-DESC = 'Material no is empty'.
    append it_error.
    SKIP_RECORD. "to skip further processing of this error record.
    ENDIF.
    like this you populate all the error records to that IT_ERRORS internal table.
    and finally download it using GUI_DOWNLOAD in the event
    '__END_OF_PROCESSING__'
    there is another way also, you can create a Session in the LSMW, and record the error records in the session then process the error records in the session
    regards
    navjot
    reward and close all ur threads
    Message was edited by:
            navjot sharma

  • Trap errors in lsmw tool

    hi all
      how can we trap errors in lsmw tool?

    hi,
    u can get the log after u process the session
    when u go to sm35 u will find the log there u will get the summery of the process in that if u choose only errors to display to then u will get only errors occured in it.
    u can refer this thread also, it will give an idea also.
    Re: errors record handling in LSMW
    Rgds
    Anver
    <i>if hlped pls mark points</i>

  • Hi all How take care of errors in LSMW..

    HI all,
       Can you people help where we are correcting errors in LSMW . How we have handle errors in LSMw.
    regards,
    anilreddy.

    Hi Anil,
    Please chk this thread. You will get the answer.
    ERROR HANDLING IN LSMW
    <b>Reward Points if Useful</b>
    Regards
    Gokul

  • Editing is terminated message when running batch input error using lsmw

    Any Idea why would I get the info message like
    "Editing is terminated message when running batch input error using lsmw"
    please suggest where to look at.
    Thanks,
    Edited by: mark_yellow mark on Jul 1, 2008 3:27 AM

    Hi Mark,
    Welcome.
    This is lsmw batch input error.while  uploading the G/L accounts using the Batch Input process (program name RFBISA00) in LSMW.this error mainly generates...
    Fix the error using logs.
    thanks
    karthik

  • Error in LSMW in Uploading Inspection Plan in QP01

    Hi All,
    I am facing problem when executing LSMW, I am Uploading Inspection Plan in QP01 transaction using Direct Input methos. The problem is on 13th step :Error that I get is 'No profile with entry tool for task list / / / in session INSPECTION_OBJ', here INSPECTION_OBJ is the name of the session. I have given the constant value of field profile (BIPKO-PROFIDNETZ) in mapping step and also activated check box 'entry tool' under profile to remove this error. But in  that case i can pass only the header data while processing the session and control does not get into Operation and characteristic screen.
    Can anyone pls help me..
    Thanks in advance...

    You might need to redo the recording all over again, BDC has plentty of scenario for screen selection to go wrong, so can't really tell what cause your problem based on your desc.  I have been stop using BDC to uplaod material since 5 years ago, I always use Direct input in LSMW and it works much better. I recomend you try the Direct input method instead of BDC if still getting problem.

  • Error in LSMW, when creating Routing - QP01

    Hi All,
    I am facing problem when executing LSMW, I am creating Routing through standard Batch input method, the problem is that on 13th step when system asks for creating batch input session, system by default takes filename.lsmw.conv, 'filename' is basically the name of file being converted internally by the system.
    Error that I get is 'No profile with entry tool for task list / / / in session ROUTING_CREA', here ROUTING_CREA is the name of the session. I have given the value of field profile in 5th step when we map the fields and give some constants value for fields when required. I have given a constant value for field profile(BIPKO-PROFIDNETZ) in data maping. Profile basically contains some default values for routing when we create routing we can give the profile and routing will capture some default field values from the profile, under profile there is a check box which is 'entry tool' that must be in active mode if operation level data is required. I have done this setting going into SPRO. Now I do not know Whether the error that I got is due to the profile problem or am I missing something else. Kindly If someone before me has already been through this problem then suggest me how to fix this problem.
    Regards,
    Ashok

    hi,
    i think, the error is due to file naming convention in SPECIFY FILE step.
    There will be a set of types of files.
    1. Presentation server file name.
    2. Application   server file name.
    etc. just double clock on the application server file name & try to change & give some meaningfulname.
    try & let us  know.
    Thanks,
    Manjunath MS

  • Error in LSMW, when creating Routing.

    Hi All,
    I am facing problem when executing LSMW, I am creating Routing through standard Batch input method, the problem is that on 13th step when system asks for creating batch input session, system by default takes filename.lsmw.conv, 'filename' is basically the name of file being converted internally by the system.
    Error that I get is 'No profile with entry tool for task list / / / in session ROUTING_CREA', here ROUTING_CREA is the name of the session. I have given the value of field profile in 5th step when we map the fields and give some constants value for fields when required. I have given a constant value for field profile(BIPKO-PROFIDNETZ) in data maping. Profile basically contains some default values for routing when we create routing we can give the profile and routing will capture some default field values from the profile, under profile there is a check box which is 'entry tool' that must be in active mode if operation level data is required. I have done this setting going into SPRO. Now I do not know Whether the error that I got is due to the profile problem or am I missing something else. Kindly If someone before me has already been through this problem then suggest me how to fix this problem.
    Thanks
    Mahen

    Hi Mahendra,
    check the following links:
    http://www.sapgenie.com/saptech/lsmw.htm
    http://www.scmexpertonline.com/downloads/SCM_LSMW_StepsOnWeb.doc
    May be u can find some help.
    Hope this helps you.
    Regards,
    Anuradha.B

  • Runtime error in LSMW to create Material Master

    Hi all,
    I am trying to create Material No. using direct input method in lsmw. The program name is RMDATIND. But while executing the last step i.e Start Direct input program I am getting a runtime error
    "A RAISE statement in the program "SAPLMG25" raised the exception
    condition "NOT_FOUND".
    Since the exception was not intercepted by a superior
    program, processing was terminated."
    I have checked all the steps of lsmw. Any idea why this specific error is coming?

    Are you able to create the material manually with the data. If you have checked the basic data view then i would check to see if base unit of measure is mandatory and if its being passed/mapped properly for the material you are creating.

  • Error in LSMW for MM41 - "No batch input data for screen SAPLMGMW 0100"

    I'm trying to create an LSMW for MM41 to create new Retail articles en Mass. This will be used to only create the Basic view as other LSMW's already exist to maintain the other views. I've created the Recording and setup the LSMW already. My data is read correctly from the source file. When I execute the batch session it fails with the following error - "No batch input data for screen SAPLMGMW 0100".
    I assume the fields in MM41 screen are not setup for batch processing. Could someone with more knowledge or experience in SAP Retail please confirm my assumption and explain where this is setup or provide an alternative to creating new articles en Mass via MM41? The direct input method is more suited for MM01 and not MM41.
    Regards
    Fawaaz

    Hi Guys,
    Thanks so much for all the prompt responses. My issue is now resolved.
    The issue, I'm sure, was my default settings in the MM41 screen which the recording probably took into account or the batch program didn't like. I deleted my recording and created a new one but before I started the recording, I went into the MM41 screen and removed all default values AND view selections. I made my Basic view selection constant in my recording and also in my field mapping. My LSMW for MM41 is now working perfectly.
    Just to answer some of the questions above, my LSMW was Reading and Converting the data in my source file fine. When I display the Read and Converted data, it shows the data fields in the correct place.
    Thanks again.
    Regards
    Fawaaz

Maybe you are looking for